C/o Mukhya Mantri Lok Bhawan in Vill. Sehri, G.P. Adhwani, Dev. Block Dehra, Dsitt Kangra H.P.

Amount

Excavation in foundations, trenches etc., in earth work,in all kinds of soil , stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing form work with steel plates 3.15 mm.thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Foundation, footings basis of columns etc. and mass concrete.

Beams, cantilever, girders and lintels Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors etc.upto 200mm. In thickness.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like

Providing and laying cement concrete 1:6:12(one cement : six sand : twelve graded/crushed stone aggregate 40mm (Forty milimetres) nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth, and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and laying cement concrete 1:4:8 (one cement : four sand : eight graded/crushed stone aggregate 40 mm (Forty milimetres) nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth, and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and laying cement concrete work 1:1.5:3 (1 Cement:1.5: Sand: 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Foundations,footings bases of columns and the like and mass concrete.

Suspended Floor roofs, landing and shelves and their support balconies,beams,girders,bressumers and cantilever upto all floor level

Columns, pillars posts and struts upto all floor level.

Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (1 cement:2 sand:4 stone aggregate 12.5 mm nominal size) and curing complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:6 (1 Cement : 6 Sand) Second Class Bricks and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Brick work using common burnt clay building bricks in superstructure in Cement Mortar 1:6 (1 Cement : 6 Sand) Second Class Bricks and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Half brick masonry in common burnt clay building bricks in superstructure in Cement Mortar 1:4 (1 cement: 4 sand) Second Class Bricks and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to coureses ) with hard stones of approved quility in foundation and plinth icluding leveling up with cement concrete 1:6:12 (1 cement:: 6sand: 12 graded stone aggregate 20 mm nominal size) at plinth level in cement mortar 1:6 (1 cement :6 sand) within all leads and lifts of matirials and other incidentals as per approved drawing and desigen and as directed by the Engineer -in-charge.

Providing second class deodar wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

P/F 12 mm thick prelaminated board both side bwp phenol bonded exterior / interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm thick frame and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing panelled glazxed or panelled glazed shutters for doors, windows and clerestory windows including balck enaelled iron but lhinges with necessary screws 35mm thick (second class deodarWood) and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing aluminium tower bolts (berrel type) anodized transparent or dyed to required shade and colour with screws etc. complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals. (125 mm)

Providing and fixing wire gauge shutters using galavanised M.S. wire gauge of I.S. gauge designation 85-G with wire of dia 0.56mm for doors windows and clerestory windows including bright finished black enamelled iron hinges with necessary screws 40mm thick second class deodar wood and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Supplying and fixing 4mm thick plain glass panes with putty and nails including removal of broken glass panes wherever necessary and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

25 mm thick Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 10 mm. thick anti skid proof stain and impect resistent heavy duty vetrified tiels Nitco or equivalant 600 x 600 x10 mm manufacturaed of approved shade and colour in flooring, treads of steps and landings laid over 12 mm thick cement mortar 1:3 (1 cement :3 sand) jointed with cement slurry mixed with pigment to much the shade of tiles as required complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Kota stone slab 25 mm thick in risers of steps,skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and laying marble work (Table rubbed and polished) in flooring 20 mm. thick base in cement mortar 1:3 (1cement:3sand) including jointing with cement mortar 1:2 (1 white cement:2 marble dust) with an admixure of pigment to match the shade of the marble. 20 mm thick White makrana marble and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge within all leads, lifts of materials and other incidentals.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charge within all leads, lifts of materials and other incidentals.

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge within all leads, lifts of materials and other incidentals.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg /sqm including filling the joints with approved adhesive complete 100mm dia pipeswithin all leads and lifts of matirials and other incidentals as per approved drawing and desigen and as directed by the Engineer -in-charge within all leads, lifts of materials and other incidentals.

5 mm thick Providing and fixing plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately) and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint. and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

In gratings framed guard bars,ladders,railling,brackets and similar works.

Providing and fixing M.S. BP Sheet 1.66 mm to 2mm thick in eaves board / facia /soffits /ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separtely) and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting readymixed paint brushing wood primer pink and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping with enamel paint other than white and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brush in to give an even shade including cleaning the surface of all dirt,dust and other foregin matters enamel paint other than white. and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with ready mixed primer and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Painting two coats(excluding priming coat on new concrete masonry/plaster surfaces with readymixed paint brushing for use on floors to give an even shade including cleaning the surface of all dirt,dust and other foreign matter and sand papering as required with paint other than white and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1:6 (one cement: six sand). and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1:6 (one cement: six sand) and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/ masonry/ plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete. and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Applying one coat of AcrylicWashable emulsion Spectrum quartz king or equivalent finish for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat i/c necessary putty to give smooth even surface, sand papered smooth complete and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing under layer of plinth protection 75mm (Seventy five milimetres) thick (Un-consolidating) bed of dry brick stone aggregate 40mm (Forty milimetres) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground. and as per direction of Engineer in charge within all leads, lifts of materials and other incidentals.

Providing plinth protection 50mm (Fifty milimetres) thick cement concrete 1:3:6 (One cement: three sand : six graded)crushed stone aggregate 20mm (Twenty milimetres) nominal size including finishing the top surfaces of concrete smooth, within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in charge.

Providing and fixing Orissa Pattern vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580 mm (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing Anglo Indian Universal closet vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately) as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers white plastic seat and cover as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing vitreous China squatting plate pattern urinal of size 450 mm x 350 mm with integral longitudinal flush pipe as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing PTMT coloured/white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately)and other incidentals, as per approved drawing, design and as directed by the Engineer-in charge.

Providing and fixing 5 litre net capacity PTMT Coloured / white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately) as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting flat back 550 x 400 mm as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 32mm dia C.P. Brass waste for wash basin or sink as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 600mm x 450 mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 600mm x 20mmm C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screwsas per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15mm dia C.P. brass bib tap with capstan head. as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15mm dia C.P. brass Pillar tap with capstan head as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15 mm dia C.P. stop cocks as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 300/450mm length 15 mm dia P.V.C connection with brass unions as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 32 mm dia PVC waste pipe for wash basin or sink as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 1000 litre net capacity PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15 mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm X 90 mm PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 110 mm dia PVC collars ISI marked including fixing with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 90 mm dia PVC collars ISI marked including fixing with approved adhesive etc. complete., as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 100 mm dia PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 610 x 510 mm with bowl depth 200 mm stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 15 mm nominal bore to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and laying 15 mm nominal bore in trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately), as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Providing and fixing 100mm nominal size diameter M.S. stay and clamps for sand cast iron / cast (spun) iron pipes, as per approved drawing, design and as directed by the Engineer-in charge within all leads, lifts of materials and other incidentals.

Karnail Singh Govt. Contractor

TARAN DEEP SINGH