REPAIR TO DRAIN, FOOTPATH, BOUNDARY WALL, SEWAGE SYSTEM ETC AT CG JETTY, ICGAE AND CGDHQ-1 AT PORBANDAR UNDER GE I CG PORBANDAR

Amount

SCHEDULE 'A'

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 deep and getting out in soft/loose soil.

Excavation in trenches not exc 1.5m wide and not exc 1.50m depth and getting out in soft/loose soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm as in soils.

M & L Sand filling under floors or in foundations including watering and consolidation for interlocking paver blocks complete all as specified and as directed by Engr-in-Charge

Removal of excavated soils to a distance n exc. 50m and depositing where directed at level exc. 1.5 km above the starting point, all as specified.

M&L Hardcore with broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L PCC type C2 (1:3:6 using 40mm graded stone aggregated) as in foundations, filling and mass concrete all as directed by Engineer-in-Charge.

M&L PCC type C-2 (1:5:10 using 40 mm graded stone aggregate) as in foundations, filling and mass concrete and sub base for paver block complete,all as specified.

M&L PCC type B2 (1:2:4 using 40mm graded stone aggregate) as in foundation / surface channel and all as specified.

M&L Plain Cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in coping, bed block benching, kerbs, mud stop, rounded or chamferred on edges and including use and waste of necessary formwork and finishing all exposed surfaces of concrete even and fair without using extra cement including weathering slightly rounded and chamfered angles and throating as directed.

M&L Pre-cast RCC 1:2:4 type B1 (using 20mm graded aggregate) as in cover slabs set in cement Mortar 1:4 and finished all exposed surfaces of concrete even and fair without using extra cement.

M & L block in course stone masonry (porbandar stone), built in CM 1:6 complete all as specified.

S&F Mild steel work as in posts/struts in fencing including cutting, tops to shape as directed, drilling holes notching for wire etc, complete conforming toFe-290 Grade E-165 complete all as specified.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered/welded or riveted, or forged into spikes; framed guard bars; Square Bar, Flat Iron, barred iron doors; ladders; framed balusters; walk ways; railings; cutting, welding , framework of water tanks and similar work con-forming to Fe.290.Gde-E-165 in Existing grill work complete all as specified and as directed by the Engineer-in-Charge.

S&F Galvanised angle Iron steel work as in posts/struts in fencing including cutting, tops to shape as directed, drilling holes notching for wire etc, complete complete all as specified.

M&L Mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to

Dismantling of GI barbed wire fencings fixed in RCC/Steel fencing posts complete all as specified & as directed.

S & F Epoxy coated (pre-painted) Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed

M & L 100 mm thick cement concret type C-2 (1:3:6, 40 mm gaded stone aggregate) as in floor repairs, sub base similar work complete all as specified

M & L 75 mm thick cement concret type B-2 (1:2:4, 40 mm gaded stone aggregate) as in floor finishes, plinth protection finished fair and even complete all as specified

M & L 40 mm thick cement concret type B-1 (1:2:4, 20 mm gaded stone aggregate) as in floor finished even and smooth with out using extra cement etc complete all as specified and as directed by Engineer in Charge.

M & L Machine pressed precast concrete interlocking paver blocks 80mm thick any shape and size conforming to IS 15658-2006 of M-40 Grade with grey cement and no pigment complete and interstices filled with sand complete all as specified and directed by Eng-in-Charge.

All as per item No.20 above, but 60mm Thick, M35 Grade

M & L 15mm thick Rendering on brick ,concrete surfaces in cement mortar 1:4 finishing even and smooth without using extra cement and similar likes at any height including necessary scafolding etc complete all as specified & directed by Eng-in-Charge.

M & L 15mm thick Rendering on brick ,concrete surfaces in cement mortar 1:4 finishing even and smooth without using extra cement and similar likes including taking down cement plaster of any description racking out joints hacking for key scrubbing down with water etc complete all as specified & directed by Eng-in-Charge.

M&L Preparing of newly plastered surfaces and applying two coats of cement based paint (of approved tint) over a coat of primer complete all as specified

M & L Preparation of new plastered/concrete surfaces of walls applying two coats of exterior acrylic emulsion (weather proof treatment) over one coat of primer, complete all as specified and as directed by the Engineer-in-Charge. ( The tint and shade be as approved by the GE)

M&L Preparing of old plastered surfaces and applying one coats of cement base paint (of approved tint) complete all as specified

M & L Preparation of old plastered/concrete surfaces of walls applying one coats of exterior acrylic emulsion (weather proof treatment) complete all as specified and as directed by Eng-in-Charge. ( The tint and shade be as approved by the GE)

M & L Preparation and applying two coats of synthetic enamel paint over a coat of Red oxide primer on new steel surfaces of any description over 10cm in width or girth, not otherwise described

S&F 150mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars in repair, complete all as specified and as directed by Eng-in-Charge. (NOTE : Excavation and Earth work shall be measured and paid separately)

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls in repairs (rate quoted includes for making good disturbed surfaces) complete all as specified and as directed by Eng-in-Charge.

All as per item No 31 above, but 75mm dia,.

S&F PVC (SWR) bends any radius of 75mm bore.

All as per item No 33 above, but 110mm bore.

S&F PVC (SWR) branch piece, single(Y) equal or unequal of 75mm bore.

S&F PVC (SWR) branch piece, single(Y) equal or unequal of 110mm bore.

S&F PVC (SWR) junction single (single T) equal or unequal of 75mm bore as specified.

All as per item No 37 above, but 110mm bore.

S&F PVC(SWR) vent cowl as specified of dia 75mm bore.

S&F PVC(SWR) vent cowl as specified of dia 110mm bore.

Cleaning of water tank of capacity not exc 250 ltrs removing all scale and dirt etc. by brushing with iron brushes, removing green algae etc. by using bleaching powder, all from tanks and from mouths of circulating pipe etc. complete all as directed by Engineer -in- Charge. (Note : The Contractor will write date of cleaning on tank as directed by Engineer-in-Charge.)

All as per item No.41 above, but exc 250 ltrs and not exc 500 ltrs capacity.

All as per item No.41 above, but exc 500 ltrs and not exc 1000 ltrs capacity.

All as per item No.41 above, but exc 1000 ltrs and not exc 2000 ltrs capacity.

M&L PCC 1:3:6 type C2 (using 40mm graded stone aggregated ) for 150mm dia pipe bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement mortar 1:2:4 type B1, (using 20mm graded stone aggregate) smooth finished and reforming, benching as required , internal dia of pipe 150mm.

Demolition and breaking up drain pipes (salt glazed stone ware) AC or reinforced concrete, set in cement mortar; internal dia of pipe 150mm.

Demolition of stone masonry built in cement mortar of any description all as specified and as directed by EIC.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

Dismantling of mild steel work as in angle iron frames/grills mild steel bars etc complete all as specified and as directed..

Taking down out (desilting) silt, brick bats debris liquid waste sludge in solid/semi solid state from Manholes including pumping out sludge wherever necessary plugging diverting the flow in the drain if necessary and staking the removed silt/sludge in deposit away from the edge of manholes as directed including use of safety belt dry cells torch for lighning in side the manholes as directed including use of safety belt dry cells torch for lightning in side the manholes and taking down similar precautionary measures and removing the sludge etc to out side MD land and cleaning the manholes with clean water etc all as specified and directed by Engineer-in-Charge.

(a) Manholes not exc depth of 1.0m

(b) Manholes depth exc 1.0m but not exc 2.0m

Taking out silt, liquid waste, sludge etc. in solid/semi solid state from septic tanks and suitably disposed off outside MD land for the following capacities :-

(a) 100 users capacity.

(b) 150 users capacity.

(c) 250 users capacity.

M&L cleaning of underground sump of the following capacity by bailing out the water in the sump below foot valve level, removing the sludge and scale out the floors, walls etc. removing green algae, with wire brush by applying bleaching powder, washing the surfaces with fresh potable water including removal of sludge and other materials to a distance not exceeding 50m complete all as directed by Engr-in-charge.

(a) Underground sump of capacity 10000 Glns.

(b) Underground sump of capacity 20000 Glns.

Cleaning of Overhead Reservoir of capacity 20000 Glns on 18Mtrs staging by scraping the inside walls by wire brush complete including removal of all sludge / silt and dirty water inside and cleaning the sump with fresh water by adding bleaching powder for infection and removing the chlorinated water afterwards including white washing with one coat of lime and writing the details of tank cleaning as directed by Engr-in-Charge.

Opening and Cleaning of obstruction/blockage in water closet, including trap, soil waste pipe, upto Ist manhole in case of ground floor or uptoTee junction for other floors complete all as specified and as directed by Engineer - in - charge.

Opening and Cleaning of obstruction/blockage in floor trap for urinal or wash hand basin or sink incl waste pipe and gully trap in case of of ground floor and Tee cross junction for other floors complete all as specified and as directed by Engineer - in - charge.

Desiliting of the existing drain/sewage line of any size such as removal of clay/ mud, junk material , plastic or biological waste , vegitation & soil etc & removal of the same from the site to a distance n.exc 500m & depositing where directed the material colleted from the drains incl muck has to be dumped in near by excavated pits & covered with soil & made good, complete all as specified and as directed by Engr-in-Charge.

M&L preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of epoxy paint over a coat of red oxide primer complete all as specified and as directed.

S&F for Epoxy coated (pre-painted) punch tape concertina coil of 610mm dia using high tensile spring steel wire 2.60 mm dia as per IS-4454 and steel tape in 19mm width as per IS-513 with and including 18 micron zink coating (Each coil is to be expanded upto 6 mtr length only) placed over U shape MS angle all as specified and directed.

M&L PVC coated 4mm dia galvanised steel wire mesh ofapparture 100 x 100mm made up into mattresses or cages, lapped, wired and laid in position, incl closing after filling complete all as specified and as directed by Engr-in-Charge.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 15 mm dia complete all as specified and as directed by Engr-in-Charge

Supply and laying of CPVC pipes, of 20mm dia SDR -11 including plain CPVC SDR fittings for Hot/cold water for sizes (outer dia ) mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all asper manufacturers recommendations and complete all as specified and as directed by Engr-in-Charge

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 20 mm dia complete all as specified and as directed by Engr-in-Charge

Supply and laying of CPVC pipes, of 25mm dia SDR -11 including plain CPVC SDR fittings for Hot/cold water for sizes (outer dia ) mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all asper manufacturers recommendations and complete all as specified and as directed by Engr-in-Charge

S&F in repaires 15mm bore Bib Cock with wall flange quarter turn, Make :Gem/Soma/Parko/Seiko) or equivalent as approved by the GE. complete all as specified and as directed by Engr-in-Charge

S&F in repaires 15mm pillar taps, cast copper alloy with captain heads chromium plated screw down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed Make : Gem/Soma/Parko/Seiko)

Supply & fix in repairs Hand Shower (health faucet) 15 mm bore with 1 meter long easy flex tube in chrome finish and wall hok with NRV (Back Flow Preventer) as approved by the GE. Make- Gem/Soma/Parko/Seiko) or equivalent. complete all as specified and as directed by Engr-in-Charge

S&F WHB of vitreous china counter sunk any size of 440x525x195 including cutting for and pinning in ends of brackets or erecting stand Make -Gem/Soma/Parko/Seiko) complete all as directed and as approved by the GE. complete all as specified and as directed by Engr-in-Charge

S&F 38mm dia PVC (flexible) waste pipe, 800mm long for Kitchen sink complete.

S&F 32mm dia PVC (flexible) waste pipe, 800mm long for WHB complete.

S&F EWC bowl for extended wall hung-WC with soft closing seat cover, size 635 x 365 x 770 including cistern with cistern fittings Make - Gem/Soma/Parko/Seiko) complete all as specified and directed by GE.complete all as specified and as directed by Engr-in-Charge

M&L Vitreous water closet (Squatting pan, Orissa pattern, size 580 x 440 white, with integral foot rests and 'P' or 'S' trap (excluding flushing cistern and flush pipe) including provision of lime concrete bedding complete fixed in repairs. any pattren complete fixed in repairs complet all as directed.

S&F Brass chromium plated swivel shower rose 450mm size including shower arm 450mm Make : Gem/Soma/Parko/Seiko) or equivalent as approved by GE. complete all as specified and as directed by Engr-in-Charge

S&F Tubular towel rail CP Brass, 60cm long between flanges complete all as specified and as directed by Engr-in-Charge

S&F Toilet Roll Holder with flap, Make : Jaquar (Cat Pat No AQN-7753) or equivalent as approved by GE. complete all as specified and as directed by Engr-in-Charge

S&F Soap Dish Polycarbide, Make : Jaquar (Cat Pat No AQN-7733) or equivalent as approved by GE. complete all as specified and as directed by Engr-in-Charge

S&F Cabinet Mirror 400 x 500 mm, Make : Prayag (Cat Pat No 554) or equivalent as approved by GE. complete all as specified and as directed by Engr-in-Charge

Supply only kitchen plate rack of stain less steel 1.00 mm thick of size 90 x 90 cm with suitable shelves/rack complete all as specified and directed by Engineer-in-Charge.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minium weight 300 gms) complete all as specified complete all as specified and as directed by Engr-in-Charge

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed by Engr-in-Charge

S & F in repair sinks drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engr-in-Charge

S&F 50mm bore High density polyethylene (LDPE) pipes of pressure rating 6kgf/sq.cm laid in trenches or in any position complete all as specified and as directed by Engr-in-Charge

S&F 25mm dia ball valves high pressure of PTMT epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed complete all as specified and as directed by Engr-in-Charge

Dismantling water tanks cpacity exc 500 and n exc 1000 ltrs and removing to store

S&F 1000 litre capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in positionall specified in SSR Part-I. complete all as specified and as directed by Engr-in-Charge

S&F Gun-metal, globe or gate valves 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge

S&F 20mm dia aluminium decorative type powder coated curtain rod or similar articles complete all as specified and as directed by Engineer in Charge

S&F aluminium decorative type powder coated brackets suitable for 20mm dia curtain rod or similar articles complete all as specified and as directed by Engineer in Charge

M&L for Polished granite stone slab 16 to 18mm thick (table rubbed and polished) in steps, jambs, pillar, window cills, cooking platform and like in cement mortar 1:4 incl pointing in white cement 1:2 using marble dust with admixture pigment to match with shade of granite including moulding at front edge all as specified and as directed as in platforms Note : Quality of granite all as approved by GE.

Vijay Construction Co

K B N TRADERS