Construction of Restaurant and Cottages at CIAL Golf Club SH Civil and Interior Works

Amount

SH: EARTHWORK Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared,including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 Sq.m on plan),including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, The rate quoted should be inclusive of dewatering. All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth.1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil, disposed earth to be levelled and neatly dressed within the site as directed by the Engineer-in-Charge.but for every additional lift of 1.5m to 3.00m or part there of. The rate quoted should be inclusive of dewatering. All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth 1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil, disposed of the earth to be levelled and neatly dressed within the site as directed by the Engineer-in-Charge. but for every additional lift of 3m to 4.5m or part thereof. The rate quoted should be inclusive of dewatering. All kinds of soil.

Earth work in excavation by means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth. and 1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil, disposed earth to be levelled and neatly dressed within the site as directed by the Engineer-in-Charge. but for every additional lift of 4.5m to 6m or part thereof.The rate quoted should be inclusive of dewatering. All kinds of soil.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual meansover areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.The rate quoted should be inclusive of dewatering. All kinds of soil

Extra rates for quantities of works, executed: In or under water and/or liquid mud, including pumping out water as required

Supplying and filling in plinth , or trenches, under floors, in areas with crusher sand including watering, ramming, consolidating and dressing including cost and conveyance of all materials, labour charges, lead, lift etc. complete at all levels as directed by the Engineer-in-Charge

Supplying and filling in plinth or trenches underfloors, foundations in areas etc with red earth in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5m including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Carriage of materials by mechanical transport including loading, unloading and stacking lead up to 5 km, including all lifts involved as directed by the Engineer-in-Charge. Excavated Earth

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 5 km for all lifts including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Shoring with sheet piles as per IS 2314 using sheet thickness not less than 6 mm and sufficient numbers of stiffness for supporting soil up to depth of 3 mtr including conveyance, labour, cost of all materials, machineries, driving and removal etc complete. as per specification & direction of Engineer-in-charge.(The method of Measurement shall be in Sq.Mtr in elevation area of the retained height). The Contractor has to submit design and shop drawing for the approval of Engineer in Charge prior to the execution.

Cutting and removal of 8 mm thick M.S. liners for piles of 450mm diameter as per detailed drawings and designs.The rate is including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Pile chipping and removing top excess lengths of RCC piles of 450m dia in same lines and levels as per structural details/instructions till sound concrete is met with, without damaging the remaining portion of pile, including chipping of the concrete, cutting of the ties reinforcement, conveying the cut bit of the reinforcement and stacking the same within the plot,straightening and bending the main reinforcement , removing debris away from the project site etc, complete including all labour charges and hire charges of tools and plants. but depth of cut pile up to 1.5 m, complete as per directions of Engineer-in-charge.

Pile chipping and removing top excess lengths of RCC piles of 450mm dia in same lines and levels as per structural details/instructions till sound concrete is met with, without damaging the remaining portion of pile, including chipping of the concrete, cutting of the ties reinforcement, conveying the cut bit of the reinforcement and stacking the same within the plot,straightening and bending the main reinforcement , removing debris away from the project site etc, complete including all labour charges and hire charges of tools and plants. but depth of cut pile up to 5m, complete as per directions of Engineer-in-charge.

Providing and applying Antitermite treatement by injecting chemical emulsion Imidacloprid emulsiable concentrate .075% for pre-constructional treatement and creating a chemical barrier as per IS 6313 (Part ll) 2001 for wall trenches, foundation, top surface of plinth filling, foundation of wall and floor, along the external perimeter of the building, etc. complete conforming to manufacturers specification and as directed by the Engineer-in-Charge.(Plinth area only to be measured for the payment ) (The above work shall be carriedout by an agency having sufficient experience and should ensure a warranty for a period of 10 years. Only skilled and experienced persons shall be employed for this purpose.)

SH: CONCRETE WORK Providing and laying in sunken floor autoclaved aerated cement brick bats filling with cement concrete 1:3:6 (1 Cement: 2coarse sand : 4 graded stone aggregate 20mm nominal size) ,cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete of specific grade properly mixed and consolidated and finished using power troweller, including cost and conveyance of all materials, labour, curing, lead lift, etc. complete as directed by Engineer-in-Charge at all levels. For screed concrete 1:2:4 (1 Cement: 2coarse sand : 4 graded stone aggregate 6mm nominal size) - All work up to plinth level

Providing and laying cement concrete of specific grade properly mixed and consolidated and finished , including cost and conveyance of all materials, labour, curing, lead lift, etc. complete as directed by Engineer-in-Charge at all levels. For screed concrete 1:2:4 (1 Cement: 2coarse sand : 4 graded stone aggregate 6mm nominal size) - All work above plinth

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification all complete as per direction of Engineer-in-Charge.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size) all complete including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Extra for laying concrete in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete.The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the P.C.C. under subsoil water with the quantity of P.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of 40 mm nominal size aggregate and 100mm crusher sand filling, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

SH: REINFORCED CEMENT CONCRETE WORK Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying, admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability but excluding the cost of centering, shuttering and reinforcement, as per direction of Engineer-in-charge. Note :- Cement content considered in this item is minimum @ 400 kg/cum. All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying, admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability but excluding the cost of centering, shuttering and reinforcement, as per direction of Engineer-in-charge. Note :- Cement content considered in this item is minimum @ 400 kg/cum. All works above plinth level upto floor V level

Providing and laying in position machine batched, machine mixedand machine vibrated design mix cement concrete of M30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying, admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability but excluding the cost of centering, shuttering and reinforcement, as per direction of Engineer-in-charge. Note :- Cement content considered in this item is minimum @ 410 kg/cum. All works upto plinth level

Providing and laying in position machine batched, machine mixedand machine vibrated design mix cement concrete of M30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying, admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability but excluding the cost of centering, shuttering and reinforcement, as per direction of Engineer-in-charge. Note :- Cement content considered in this item is minimum @ 410 kg/cum. All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more, all complete as per direction of Engineer-in-Charge. including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more, all complete as per direction of Engineer-in-Charge. including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Centering and shuttering including strutting, etc. and removal of form for: Foundations, footings, bases of columns, etc for mass concrete including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Centering and shuttering including strutting, propping etc. and removal of form for all heights :Suspended floors, roofs, landings, balconies and access platform including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Centering and shuttering including strutting, propping etc. and removal of form for all heights :: Columns, Pillars, Piers, Abutments, Posts and Struts including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Centering and shuttering including strutting, propping etc. and removal of form for all heights :Edges of slabs and breaks in floors and walls under 20 cm wide including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Stairs, (excluding landings) except spiral-staircases including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Centering and shuttering including strutting, etc. and removal of form for: Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Extra for laying reinforced cement concrete in or under water and / or liquid mud, including cost of pumping or bailing out water and removing slush etc., complete. The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions.

SH : MASONRY WORK Providing and constructing Solid concrete block masonry M-10 grade in C.M1:6 (1cement, 6 coarse sand) with Solid blocks of 30x20x10 cm size or nearest and approved quality including scaffolding, raking out of joints,curing, cost and conveyance of all materials,labour, lead, lift, etc. complete for all types of masonry works in super structure above the highest plinth level as directed by Engineer-in-Charge at all levels.

Providing and constructing Solid concrete block masonry M-10 grade in C.M 1:6 (1cement, 6 coarse sand) with Solid blocks of 30x20x15 cm size or nearest and approved quality including scaffolding, raking out of joints,curing, cost and conveyance of all materials,labour, lead, lift, etc. complete for all types of masonry works below plinth level as directed by Engineer-in-Charge at all levels.

Providing and constructing Solid concrete block masonry M-10 grade in C.M1:6 (1cement, 6 coarse sand) with Solid blocks of 30x20x15 cm size or nearest and approved quality including scaffolding, raking out of joints,curing, cost and conveyance of all materials,labour, lead, lift, etc. complete for all types of masonry works in super structure above the plinth level as directed by Engineer-in-Charge at all levels.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesivemortar all complete as per direction of Engineer-inCharge. (The payment of RCC band and reinforcement shall be made for seperately)

SH : STEEL WORK Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing structural decking panel of approved make of 960 mm effective cover width profile with 51 mm deep ribs, pitch of 316 mm centre-to-centre, with 3mm deep and 19 mm long embossment on either side of webs which are diagonally opposite to each other, the top embossment on is 1.5mm deep and 15.21mm wide providing the mechanical interlocking between the steel and concrete ensuring adequate composite action between steel and concrete. The panel shall have v” shape of 10mm deep on rib and pan as a stiffener and male and female interlocking at side lap. The feed material shall be 1.2mm Base Metal Thickness (i.e. excluding coating thickness) with zinc coating of Z275 (275g/m2 minimum coating mass), 550 MPa Yield strength grade confirming to IS513 or ASTM A653M. The required accessories (edge forms /flashing) shall be made of same material of decking panel. Shear studs of approved make shall be used with metal decking with steel beam structure or as per manufacture recommendation. The deck sheets shall be supplied in required sizes according to the cutting schedule.Cutting of sheets to length shall not be permitted at site.Cutting and trimming of small openings which were not finalized at the time of working drawings can be allowed at site. Power tools shall be used for cutting. No gas cutting shall be done on the sheet. Before installing decking sheet, it shall be ensured that the beam support is in true planes, correctly placed and securely fixed. The work shall be executed as per manufacturers specifications by a specialised agency having sufficient experience in similar work and should ensure a warranty for any defective installation, material for a period of 5 years from the date of completion of said work.

Providing & fixing of external grade wooden finished powder coated non polish SS 304 grade handrail.Top & vertical members are ss square tubes of size 50x50x2.5mm supported by the base plate of 5mm thick fixed to the floor using anchor fasteners & intermediate horizontal members are ss square tubes 40x40x2 mm .The members are connected by welding.Top & Bottom members connected with synthetic hemp rope of 1cm dia as per the design and approved architectural drawing.Rate is inclusive of all material,assembling, errection, welding, curvaturing, grinding, buffling,anchor fasteners, etc ,other accessories etc complete.-Railing Height – 1000mm from FFL-Stair and Ramp Handrail

Providing and fixing railing with bottom aluminium channel of size 120 mm x 42 mm (5.35 KG/Mtr) of approved brand and Top Rail with SS304 Grade of size 40 x 40 x 2 mm (IM055T/equivalent)and 12 mm thick Toughened clear glass is fixed to the groove with EPDM gasket, The bottom section is fixed to the floor using Hilti/Fischer or Equvalent Chemical Anchor Bolt, The rate is including welding, grinding, buffing, polishing and fixing the railing with necessary accessories of required size, all complete as per the approved design and approval of Engineer-in-charge.Railing Height – 1000 mm from FFL-Balcony Rail

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. Electric resistance or induction butt welded tubes

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete s directed by Engineer-in-Charge at all levels.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying protective coating on steel structures two coats of aliphatic polyurethene of 35 microns each per coat with not less than 45% volume solids and DFT of 35 micron each over a base coat of fast drying, high solids two pack epoxy coating not less than 80% volume solids of DFT 130 microns with primer coat of two pack epoxy not less than 71% volume solids and a DFT of 50microns or equivalent. All areas to be blast cleaned to Sa 2.5(ISO8501- 1:2007) before applying primer The rate shall including cost and conveyance of all materials, labour charges, lead, lift etc complete as directed by Engineer-in-Charge at all levels. (Protective coating including primer coat on external steel structure shall be measured and paid separately)

Providing and fixing high-performance galvanized steel M20 anchor rod of 300 mm lenght, 8.8 grade strength of approved make including cost and conveyance of all materials, labour charges, lead, lift, etc complete as directed by Engineer-in-Charge at all levels.(The above work shall be carried out by an agency having sufficient experience.

Providing and fixing of electrically operated perforated Rolling Shutter with powder coated finish of approved shades and standards, constructed of galvanized steel slats 1 mm thick , guide rails and bottom profile,Mild steel roller cage assembly,side brackets with bearings, Automation system hardware and accessories shall have 2 hour Fire Rating. The Slat Curtain with High Grade Special quality galvanized steel interlocked slats as per BS standards and designed edge end lock to achieve maximum holding strength.Bottom Plate with Structured galvanized steel L-shaped section welded with angle stiffener/heavy tubes 35 x 35 x 5 mm. Side Guides with Specially designed box type galvanised steel side guides 3.0mm thk surface mounted type should guide the slat curtain smoothly.Mild Steel bracket plate shall have minimum of 3.0 mm thickness of required dimension .Bracket plate dimensions vary as per size of shutter. Load of shutters transfers through brackets.Roller Shaft shall be of Heavy-Duty with inbuilt reductiongears, In built mechanical limit units and thermal protector.Manual override shall also be added in case of power failure.The rate is including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. Size of the opening: 380 cm x 410 cm

Providing and fixing aluminium work for wood finish 2-Track 2-Shutter sliding glazed Doors comprising of aluminium multi- chambered frame with in-built roller track and sash extruded profiles of 55 mm x 41 mm Sliding Track,37 mm x 62 mm Shutter (1.2 mm thickness) using (1,2) 21 MM Dgu Toughened Glass-(5 MM Tg+10 MM Airgap +6 MM Tg) or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24. including cost and conveyance of all materials, labour charges etc as per drawing. complete at all levels as directed by Engineer-in-charge Size : 230x240cm

Providing and fixing aluminium work for wood finish 2-Track 2-Shutter sliding glazed Doors comprising of aluminium multi- chambered frame with in-built roller track and sash extruded profiles of 55 mm x 41 mm Sliding Track,37 mm x 62 mm Shutter (1.2 mm thickness) using (1,2) 21 MM Dgu Toughened Glass-(5 MM Tg+10 MM Airgap +6 MM Tg) or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24. including cost and conveyance of all materials, labour charges etc as per drawing. complete at all levels as directed by Engineer-in-charge Size : 280x240cm

Providing and fixing aluminium work for wood finish Open windows with extruded outer frame section 60 mm x 50 mm, Shutter 100 mm x 60 mm, 73 mm x 51 mm (1.2 mm thickness).Using, 6 mm Toughened clear glass or required thickness . Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24. all complete as per architectural drawings and the directions of Engineer-in-charge. Size : 60x90cm

Providing and fixing aluminium work for wood finish ventilator extruded profiles of Outer Frame 60 mm x 50 mm, 51 mm x 73 mm Mullion (1.2 mm thickness) . Using, 6 mm Toughened clear glass or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24.including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Size : 90x60cm

Providing and fixing aluminium work for wood finish Ventilator extruded profiles of Outer Frame 60 mm x 50 mm, 51 mm x 73 mm Mullion (1.2 mm thickness) . Using, 6 mm Toughened clear glass or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24.including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Size : 120x60cm

Providing and fixing aluminium work for wood finish fixed windows extruded profiles of Outer Frame 60 mm x 50 mm, 51 mm x 73 mm Mullion (1.2 mm thickness) .using (1,2) 21 MM Dgu Toughened Glass-(5 MM Tg+10 MM Airgap +6 MM Tg) required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24.including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Size : 200x180cm

Providing and fixing aluminium work for wood finish 2-Track 2-Shutter sliding glazed Windows comprising of aluminium multi- chambered frame with in-built roller track and sash extruded profiles of 55 mm x 41 mm Sliding Track,37 mm x 62 mm Shutter (1.2 mm thickness) using (1,2) 21 MM Dgu Toughened Glass-(5 MM Tg+10 MM Airgap +6 MM Tg) or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24. including cost and conveyance of all materials, labour charges etc as per drawing. complete at all levels as directed by Engineer-in-charge W4- 1200X1200 mm

Providing and fixing aluminium work for wood finish fixed windows extruded profiles of Outer Frame 60 mm x 50 mm, 51 mm x 73 mm Mullion (1.2 mm thickness) . Using, 6 mm Toughened clear glass or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24.including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge W2- 900X3350 mm

Providing and fixing aluminium work for wood finish fixed windows extruded profiles of Outer Frame 60 mm x 50 mm, 51 mm x 73 mm Mullion (1.2 mm thickness) . Using, 6 mm Toughened clear glass or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24.including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge W3- 1200X3350 mm

Providing and fixing aluminium work for wood finish fixed windows extruded profiles of Outer Frame 60 mm x 50 mm, 51 mm x 73 mm Mullion (1.2 mm thickness) . Using, 6 mm Toughened clear glass or required thickness .Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24.including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge W5- 3450X3350 mm

Providing and fixing aluminium work for wood finish Open windows with extruded outer frame section 60 mm x 50 mm, Shutter 100 mm x 60 mm, 73 mm x 51 mm (1.2 mm thickness).Using, 6 mm Toughened clear glass or required thickness . Fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.The gap, if any between the frame and RCC / Masonry wall shall be filled and finished with Silicon weather sealant.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / stainless steel screws,G.I zinc plated Hilti screw 8X80 mm size for fixing frame to finished wall and necessary stainless steel screws 8X9,8X19,8X24. all complete as per architectural drawings and the directions of Engineer-in-charge. W1- 900X1200 mm

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring - floor spring BTS 75 90*W/D, Handle 600x32mm SS 304 Grade , Xlc -7058 Glass to glass Lock One Key One Knob, fixing arrangement and making necessary holes etc. The rate shall includes cost and conveyance of all materials, all structure if any to support the patch fitting door,all hardwares, labour charges, lead, lift, cleaning and clearing the debris from all levels and disposing complete as directed by Engineer-in-Charge and as per drawing at all levels. The Patch Fittings & Floor Spring fittings shall conform to EN 1154 Standards with adjustable spring strength (EN1-4) All SS material shall be Mirror finish and glass shall be heat soaked (Double leaf)

Supply and installation of ABS Door (Acrylonitrile Butadiene Styrene Doors) with frame made of Foamed PVC Polystyrene Frame of 110x40mm. The Frame would be fixed to masonry wall using Anchor fastners The gap between wall and frame to be filled with Silicone Sealant with 35 mm thick shutter fabricated with front and back panels consisting of imported korean made ABS SHEETof thickness 1.35mm fused with deco film of thickness 0.15mm . The shutter frame is made with solid PURPLE PVC BAR of section size 32/35mm and thermally bonded with high temperature on all four corners. The internal portion is filled with Tubular core board (GERMANY) and pressed with high pressure ABS SHEETS on both sides with Architraves 58x15mm/6x12mm on external and internal sides respectively including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge D (Size - 80 x 240 cm )

Providing and fixing of Fully Insulated Non Metalic Fire cum Acoustic Wooden fire doors as per IS 3614:2021, for 120 min integrity & insulation. The door is manufactured made out of thoroughly seasoned hard wood. The moisture content of wood material used at the time of construction of wooden composite fire door sets comprises of both frame and shutter shall not be more than 15% approx.in accordance with IS 287. The offered door must carry acoustic properties certification test evidence.To achieve Acoustic properties, the shutter thickness should be minimum 77mm. Door and frame should be factory finished with fire retardent primer FR880. All accressesories like hardware, vision panel, fire seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS 3614:2021. Every door must carry a label confirming to type of door & its fire rating.Door frame shall be Single rebate profile of section 140 x 90 mm made out of Ivory Coast Teak wood ( 2nd Class )having density of 550- 600 kg/m3 with factory made groove of suitable size so as to accomodate Fire seal of size 20x4mm An EPDM seal also to be provided in the frame to checkspread of smoke.The frame must be primed with Fire retardant primer FR880 .Wooden shutter must be of minimum 77mm of thickness finished with 6mm thick commercial ply on both faces. The Shutter should be provided with 6mm thick commercial ply along with 1mm thick laminate on both faces . The composite thickness of the core insulation will be 63mm consists of minimum 10mm thick Calcium Silicate boards of Hilux / Pamtech make and treated wool Insulation material . The calcium silicate board must have Density not more than 900kg/m3, having thermal conductivity 0.15W/mK . The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealedwooden lipping . The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges of size 100 x89x3 mm with SS screws along with all suitable hardware.The NABL accredited lab certificate shall be produced.The rate shall include cost and conveyance of all materials,labour charges etc. complete at all levels as directed byEngineer-in-charge D6 (Size : 100 x 240 cm)

Providing and fixing of Fully Insulated Non Metalic Fire cum Acoustic Wooden fire doors as per IS 3614:2021, for 120 min integrity & insulation. The door is manufactured made out of thoroughly seasoned hard wood. The moisture content of wood material used at the time of construction of wooden composite fire door sets comprises of both frame and shutter shall not be more than 15% approx.in accordance with IS 287. The offered door must carry acoustic properties certification test evidence.To achieve Acoustic properties, the shutter thickness should be minimum 77mm. Door and frame should be factory finished with fire retardent primer FR880. All accressesories like hardware, vision panel, fire seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS 3614:2021. Every door must carry a label confirming to type of door & its fire rating.Door frame shall be Single rebate profile of section 140 x 90 mm made out of Ivory Coast Teak wood ( 2nd Class )having density of 550- 600 kg/m3 with factory made groove of suitable size so as to accomodate Fire seal of size 20x4mm An EPDM seal also to be provided in the frame to checkspread of smoke.The frame must be primed with Fire retardant primer FR880 .Wooden shutter must be of minimum 77mm of thickness finished with 6mm thick commercial ply on both faces. The Shutter should be provided with 6mm thick commercial ply along with 1mm thick laminate on both faces . The composite thickness of the core insulation will be 63mm consists of minimum 10mm thick Calcium Silicate boards of Hilux / Pamtech make and treated wool Insulation material . The calcium silicate board must have Density not more than 900kg/m3, having thermal conductivity 0.15W/mK . The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealedwooden lipping . The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges of size 100 x89x3 mm with SS screws along with all suitable hardware.The NABL accredited lab certificate shall be produced.The rate shall include cost and conveyance of all materials,labour charges etc. complete at all levels as directed by Engineer-in-charge D6 (Size : 120 x 240 cm)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing & fixing compact laminate toilet front partition of following standard dimension which includes 600mm door size width made of 12mm thick compact laminates made out of urea free, thermosetting phenolic resins treated Kraft papers as core material and amino plastic resin treated decor papers on the finish surface. This includes providing and fixing in position necessary hardware made out of stainless steel (Grade 316) as per manufactures specification like (1) Door knob, (2) Spring loaded hinges (3) Slide Bolt with occupancy indicators (4) Coat hooks. Toilet front partition with dimension of 2050 mm height x 1000 mm width which includes 600 mm door size width.The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Proving and fixing urinal partition made of 10 mm thick frosted curved glass of 450mm(D) x 900mm(H) Fixed on wall with the help of SS grade 316 brackets including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. Purchase Price :Rs. 2100 Each (Excluding GST) . Any deviation plus or minus in the purchase price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor.

Providing and fixing Toilet Cubicle with dimension of 1800 mm width x 1950mm Height which includes 75mm door size width, 8/10mm thickness tempered glass by heating 690° C with international standards frow jaquars own plant, An Anti Lime scale coating applied on glass, Hydrophobic chemical coated in glass for prevention of all kind of stains on the glass 2 years warranty for this application. This includes providing and fixing in position necessary hardware made out of brass , stainless steel (Grade 316) and treated aluminium channels as per manufactures specifications. Solid hinges coming in brass with chrome coated stabilizer rod and towel rod coming in stainless steel, sliding rail in treated aluminium profile. Floor clamps stainless steel. All hardwares are covered 5 years Replacement warranty.

Providing and fixing Toilet Cubicle with dimension of (1400+1200)mm width x 1950 mm Height which includes 75mm door size width, 8/10mm thickness tempered glass by heating 690° C with international standards frow jaquars own plant, An Anti Lime scale coating applied on glass, Hydrophobic chemical coated in glass for prevention of all kind of stains on the glass 2 years warranty for this application. This includes providing and fixing in position necessary hardware made out of brass , stainless steel (Grade 316) and treated aluminium channels as per manufactures specifications. Solid hinges coming in brass with chrome coated stabilizer rod and towel rod coming in stainless steel, sliding rail in treated aluminium profile. Floor clamps stainless steel. All hardwares are covered 5 years Replacement warranty.

Providing and fixing Toilet Cubicle with dimension of 2500mm width x 1950 mm Height which includes 75mm door size width, 8/10mm thickness tempered glass by heating 690° C with international standards frow jaquars own plant, An Anti Lime scale coating applied on glass, Hydrophobic chemical coated in glass for prevention of all kind of stains on the glass 2 years warranty for this application. This includes providing and fixing in position necessary hardware made out of brass , stainless steel (Grade 316) and treated aluminium channels as per manufactures specifications. Solid hinges coming in brass with chrome coated stabilizer rod and towel rod coming in stainless steel, sliding rail in treated aluminium profile. Floor clamps stainless steel. All hardwares are covered 5 years Replacement warranty.

SH: FLOORING WORK Providing and laying Polished Granite stone flooring of approved colour, design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing,cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Purchase price : Rs.2627 / Sq.mtr (Excluding GST ).Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing,cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Purchase price : Rs.1460 / Sq.mtr (Excluding GST ).Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Extra for fixing granite stone, over and above corresponding basic item,in facia and drops of width upto 150 mm with epoxy resin based adhesive,including cleaning,cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge .Purchase price : Rs.2627 / Sq.mtr (Excluding GST ).Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 600x600 mm, Purchase price :Rs. 990 / Sqm Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and fixing fully vitrified tile skirting in risers of steps and dado up to 2 m height with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile600x600 mm, Purchase price :Rs. 990 / Sqm (Excluding GST ) Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and fixing fully vitrified tile skirting in risers of steps and dado up to 2 m height with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980,complete inlcuding cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 1600x800 mm, Purchase Price :Rs. 1045 Per Sqm (Excluding GST) Any deviation plus or minus in the purchase price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 1600x800 mm, Purchase price :Rs. 1045 / Sqm (Excluding GST ) Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Size of Tile 1200x600 mm, Purchase Price :Rs. 1163 Per Sqm (Excluding GST) Any deviation plus or minus in the purchase price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and fixing fully vitrified tile skirting in risers of steps and dado up to 2 m height with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 1200x600 mm, Purchase Price :Rs. 1163 Per Sqm (Excluding GST) Any deviation plus or minus in the purchase price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Size of Tile 58 x 250 mm, Purchase price :Rs. 3172.4 / Sqm Any deviation plus or minus in the purchase price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying Calibrated Matt finish Kota stone slab of size 600x600x20mm over 25 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand). The rate is inclusive of all operation material and required pattern ,cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge.The purchase price (excluding GST) of tile shall be as mentioned below in basic price and any deviation plus or minus in the purchase price will be adjusted (paid extra/deducted) at the time of billing. The work shall be carried out by an agency having good experience with the skilled labours on the specified work mentioned above. Purchase price :Rs. 1097.52 per Sqm Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and fixing fully vitrified tile skirting in risers of steps and dado up to 2 m height with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 1200x600 mm, Purchase price :Rs. 818 / Sqm (Excluding GST ) Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile1200x600 mm . Purchase price : Rs.926 per Sqm (Excluding GST ).Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully Vitrified matt tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in dadoing, with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 1200x600 mm .Purchase Price : Rs.883 per Sqm(Excluding GST ).Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 198 x198 mm, Purchase Price :Rs. 2193.65 per Sqm (Excluding GST) Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and fixing fully vitrified tile skirting in risers of steps and dado up to 2 m height with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile1200x600 mm . Purchase Price : Rs.926 per Sqm (Excluding GST ).Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.50 Sq.m,including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Purchase price :Rs. 2440 per Sqm Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying fully vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 3mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack, abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Size of Tile 398 x 800 mm, Purchase Price :Rs. 1356 per Sqm (Excluding GST) Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing nosing for pre finished granite treads of steps. The rate is inclusive of cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge

Providing edge moulding to 18 mm thick granite work, including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work (Excluding GST ).Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in flooring and only skilled and experienced persones shall be employed for this purpose.

Providing and laying 5mm thick tile protection sheet ( a closed cell, polymer based micro cellular foam, reinfirced with high performance polymerson finished) vitrified tile/ engineered stone/ Laminated wooden / vinyl and other flooring for protection and removal of the same after completion of all other works, including cost and conveyance of all materials, labour charges, lead, lift, curing , till handover etc, complete as directed by Engineer in charge at all levels

SH : CEILING WORKS Providing and fixing Gypsum false ceiling (12.5 mm) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/Sq.m (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings,trap doors,grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks) The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing and fixing 12.5 mm thick tapered edge gypsum moisture resistant board at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/Sq.m (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks).The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing and fixing partition upto ceiling height consisting of G.I. frame and calcium silicate board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 66mm overall thickness Partition with 8mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./ sq.cm

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Providing & Fixing horizontal level suspended ceiling comprising of Galvanized steel Lay-in Plain metal ceiling consisting of 600x600mm (Nominal Size) 120 gsm galvanized steel as per IS 277 (2003) suitable for architectural finishes in 0.5 mm thickness as per IS:513 (1994) in approved color with Square Tegular/Microlook 90 degree edge having 8mm drop and 5.5mm flange. The difference between the 2 diagonal dimensions of the tile to be less than 1mm. Tiles shall be flattened by precision leveller to minimize sag to less than 1/400mm. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 Hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level 25±5% at 60˚ as per ASTM D523. The tile shall have a Light Reflectance of ≥ 63% in accordance to ASTM 1477-98 and Fire Performance of Class 0/1 as per BS 476 Part 6 & 7 in module size of 600x600mm..The tile shall be laid on 15 mm wide T - section flanges colour global white (matching to tile colour) having double stroke rotary stitching on all T sections i.e. the Main Runner at a spacing of 1200 mm & Cross Tees at a spacing of 600 mm with a web height of 32mm (all sections). The deflection loading of the system shall be 7.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 8.5kg/m. The end details of the cross tee shall be made of pre hardened steel clip fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel 90 gsm and pre-painted steel with baked polyester paint of 0T bending capability. Suspension System consist of accessories manufactured and supplied by Manufacturer consisting of M6 Anchor Fasteners with hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs connected to RC C Slab /structural steel system. Additionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners.The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Contractor should submit detailed design and corresponding calculations of design of all structural suspension system of metallic false ceiling, structural steel support and shop drawings vetted by a consultant in accordance with design parameters specified by the consultant and the codal requirements of BIS (Bureau of Indian Standards) latest version, all relevant safety codes, National Building Code and DIN ISO 9001, LEED & DGNB, EN 13964, EN 13501-1 building material class A2-s1, do Class A tested to ASTM E 84 class 0 tested to BS 476 part 6/7, E DIN EN ISO 354, ASTM C 423 etc to the Engineer-in-Charge.Vetting shall be in the scope of the Contractor. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for installation, ceiling panels and supporting system for & a period of 10 years from the date of completion of the said work. The measurement shall be taken along the girth on the bottom side of the ceilings, in square meters and deduction shall be made for all openings exceeding 0.4 Sqm in area.

Providing and fixing 1 layer magnesite bonded wood wool acoustic panel of approved make. 1mm thick fibre, exquisite surface structure, building biology recommended, size 600 x 1200 x 25mm, having edge detail SK-04, weight 11.30Kg/Sq.m, fire protection class B-s1,d0 as per EN 13501-1 & Humidity Resistance of 95%. Thickness Tolerance T2 (± 1 mm) according to EN 13168. Ceiling Installation : The wood wool panels to be laid in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanized @ 90 gsm/Sq.m) consisting of Main "Tee", size 24W x 38H x 3600L mm made from 0.30 mm thick sheet spaced at 600mm centre to centre and Cross "Tee", size 24W x 38H x 600L mm made of 0.30 mm thick sheet to be interlocked between the main T runners at the distance of 1200mm centre to centre to create 1200x600mm module to lay ceiling tiles of approved surface pattern in the grid including, wherever required, cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. The perimeter trims to be of 24W x 24H x 3600L mm and 0.30 mm thick. Main "Tees" to be suspended from ceiling using M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs suspended from the RCC Slab/ structural steel system. Adj ustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners. The first suspension from the perimeter trim should not exceed 300mm. The bottom exposed width of 24mm of all T-sections shall be factory pre-painted with polyester paint. Wall Installation: UD profile of width 28mm and 0.60mm thick is fixed to the wall, such that the base of the UD profile is 25mm above the planned finished ceiling level / 25mm less than the finished wall level. The ends of the CD profile is to be inserted into the UD profile and placed at a distance of 600mm centre to centre and is to be secured to the soffit/wall using the Universal Bracket. The Universal brackets are to be fixed to the soffit/wall at a distance of 900mm using 6mm dia anchor fasteners (for ceilings) and wall screws (for walls). Wood wool boards to be screw fixed to the CD profile using 6 screws (per board) 50/4.50mm dia screws. The wood wool board should be backed by 40mm thick glass wool slabs packed in 1200 x 600mm polythene bags having a gross density of 50kg/m3. The finished face of wood wool panels have to be installed at a distance of 300mm from the soffit to achieve a NRC of 0.90 as per ASTM C423. Panels can be spray painted on site (before installation) under supervision of manufacturer. The wood wool board should be backed by 40mm thick rock wool slabs packed in 600 x 600 polythene bags having a gross density of 50kg/m3. The finished face of wood wool panels have to be installed at a distance of 300mm from the soffit to achieve a NRC of 0.90 as per ASTM C423. Panels to be spray painted on site under supervision of manufacturer.The rate is including spray painting , cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.Contractor should submit detailed design and corresponding calculations of design of all structural suspension system of false ceiling, structural steel support and shop drawings vetted by a consultant in accordance with design parameters specified by the consultant and the codal requirements of BIS (Bureau of Indian Standards) latest version, all relevant safety codes, National Building Code and DIN ISO 9001, LEED & DGNB, EN 13964, EN 13501-1 building material class A2-s1, do Class A tested to ASTM E 84 class 0 tested to BS 476 part 6/7, E DIN EN ISO 354, ASTM C 423 etc to the Engineer-in-Charge.Vetting shall be in the scope of the Contractor. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for installation, ceiling panels and supporting system for & a period of 10 years from the date of completion of the said work. The measurement shall be taken along the girth on the bottom side of the ceilings, in square meters and deduction shall be made for all openings exceeding 0.4 Sqm in area.

Providing & Fixing Wooden finished Suspended Ceiling System with Microlook edge tiles and edge profile in exposed grid. The 18mm thick Plain Tile shall be made of Medium Density Fibre of density 700+ Kgs/m3. The tile shall have melamine laminate finish of approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut) on visible side and backing laminate (same shade) on the reverse with 0.8mm matching PVC edge banding in module size of 600mm x 600mm. The edges of the tile shall be Square Tegular/Microlook 90˚ having 8mm drop using 3mm thick compact board spline. The tile shall have Humidity Resistance (RH) of 70%, with sag limited to 1/300mm. The tile shall have a Fire Performance of class 1 according to BS 476 part 7. The tile shall be laid on 15 mm wide T - section flanges having double stroke rotary stitching on all T - sections i.e. the Main Runner at a spacing of 1200 mm and cross tee at a spacing of 600 mm with a web height of 38 or 43mm (all sections) as per manufacturers reccomendation. The deflection loading of the system shall be 12.5-15.6 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360 within suspension points) with deflection loading of 15.5 - 18.6kg/m2. The end details of the main beam and cross tee shall be made of pre hardened steel clip fixed to the ends. The cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T - Sections shall be made of hot dipped galvanized steel of 100 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. Suspension System consist of accessories manufactured and supplied by Manufacturer consisting of M6 Anchor Fasteners with hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs connected to the RCC Slab /structural steel system. Additionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners.The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Contractor should submit detailed design and corresponding calculations of design of all structural suspension system of metallic false ceiling, structural steel support and shop drawings vetted by a consultant in accordance with design parameters specified by the consultant and the codal requirements of BIS (Bureau of Indian Standards) latest version, all relevant safety codes etc as per the direction of the Engineer-in-Charge. Vetting shall be in the scope of the Contractor. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for installation, ceiling panels and supporting system for & a period of 10 years from the date of completion of the said work. The measurement shall be taken along the girth on the bottom side of the ceilings, in square meters and deduction shall be made for all openings exceeding 0.4 Sqm in area.

Supply and fixing of Exterior PVC Ceiling of panel sizes of 250mmx 2950mm or nearest, durable and resistant to moisture, water and borer-fungus-termite attack complies with IS 875 part 3 1987 on wind loading, the same should be tested for and complying to a wind Ibad resistance of minimum 1.2 kpa (as tested by an independent and competent authority) as per prevalent and in practice wind loading norms and procedures. Panels to be installed with Aluminium sections of suitable gauge as per the installation of planks & size according to site conditions . Panels with suitable trims for edge profiles, Connecting profiles, starter and ventilation profile, interior and exterior corner profiles shall be used . Panels must be maintenance free , rust proof and are 100% Water proof. 10 years warranty for colour & finish of the panels.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. Contractor should submit detailed design and corresponding calculations of design of all structural suspension system of false ceiling structural steel support and shop drawings vetted by a consultant in accordance with design parameters specified by the consultant and the codal requirements of BIS (Bureau of Indian Standards) latest version, all relevant safety codes, etc as directed by the Engineer-in-Charge.Vetting shall be in the scope of the Contractor. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for installation, ceiling panels and supporting system for & a period of 10 years from the date of completion of the said work. The measurement shall be taken along the girth on the bottom side of the ceilings, in square meters and deduction shall be made for all openings exceeding 0.4 Sqm in area.

Supply & fixing of Suspended Aluminum sections of 50x75mm and 0.5mm thick powder coated with wood finish with U shaped profiles in varying grid dimensions as per drawing detail. The section is suspended from RCC Slab / Structural system with plywood backing supported on aluminium sections / structural frame work. Aluminium section , Structural frame work, and Plywood shall be measured under relevant items. Powder coated aluminium section to be fixed to plywood backing using anchor fastners each at anchorage ends.and all required accessoriers at all levels & all heights of building all complete as per the 3D views and architectural drawings. The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. The work shall be executed as per manufacturers specifications by a specialised agency having sufficient experience in similar work and should ensure a warranty for any defective installation, material for a period of 10 years from the date of completion of said work.

SH : ROOFING Providing and laying pressed clay tiles including top ridges and end ridges (as per approved pattern 20 mm nominal thickness of approved size) on rough surface of roof laid over concrete battens . Concrete battens are made up of cement mortar 1:4 (1 cement : 4 coarse sand)of size 100x75mm thick are laid at intervals @380mm c/c.Battens require 3-5 days curing .Tiles are fixed on battens using the legs provided in the tiles, finished and completed as per the approved architectural drawing.The rate shall include cost and conveyance of all materials including end and top ridges, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. (The above work shall be carriedout by an agency having sufficient experience. Only skilled and experienced persons shall be employed for this purpose.)

Providing & fixing on roof pressed clay tile of 20 mm nominal thickness and of approved size , make and as per approved pattern on steel frame work complete (steel frame work to be paid separately).The rate shall include cost and conveyance of all materials including end and top ridges, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. (The above work shall be carriedout by an agency having sufficient experience. Only skilled and experienced persons shall be employed for this purpose.)

Providing and fixing of UPVC (Unplasticized Poly Vinyl Chloride) rain water eave gutter of width 200mm , 100 mm depth and 3 mm thickness of approved make and colour with center joint,corner , end drop , center drop and GI clamp complete including cost and conveyance of all mat erials, scaffolding, lead, lift, labour charges etc. complete at all levels as directed by Engineer-in-Charge

Supply and installation of rainwater gutter at any roof level using 1mm thick SS 304 grade Stainless steel sheets including finishing joints with tig argon welding as approved by the Engineer in Charge. The gutter shall be supported on MS brackets and M.S brackets shall be measured and paid under relevant item. Gutter shall receive the downspouts at designed intervals and all joints with downspouts shall be welded and made water space tight. Gutter shall be fixed in lines and levels including cost and conveyance of all materials, labour charges, scaffoldings etc. complete as per standards and as directed by Engineer-in-charge at all levels Note: Water tightness shall be ensured by ponding water for 7 days and got approval from Engineer in charge

SH : FINISHING WORKS 12mm cement plaster of mix 1:4 (1 cement : 4 fine sand)including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

12 mm cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 fine sand) including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

15mm cement plaster of mix 1:4 (1 cement : 4 fine sand)including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing control joints in 6mm Width X 10 mm depth at 3M X 4M panels. along the length and breadth of the entire screed area. The joint can be provided by using a saw cutting machine attached with a 3 mm blade within 18-24 hrs of application of the screed. 28- 30 days later, these joints can be filled with one-part moisture-curing Polyurethane Sealant.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two or more coats to acheive an even coat.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 Sq.m over and including priming coat of exterior primer applied @ 2.20 kg/10 Sq.m).The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Finishing walls with textured exterior paint of required shade (Two or more coats applied @ 3.28 ltr/10 Sq.m) over and including priming coat of exterior primer applied @ 2.20kg/10 Sq.m.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing and applying protective coating on external steel structures two coats of aliphatic polyurethene of 35 microns each per coat with not less than 45% volume solids and DFT of 35 micron each over a base coat of fast drying, high solids two pack epoxy coating not less than 80% volume solids of DFT 130 microns with primer coat of two pack epoxy not less than 71% volume solids and a DFT of 50microns or equivalent.All steel surface to be cleaned throughly withstrong detergents and high pressure fresh water to remove oil, grease, salt and contaminations.All areas to be blast cleaned to Sa2.5(ISO8501-1:2007) before applying primer . The rate shall including cost and conveyance of all materials,labour charges ,lead,lift etc complete as directed by Engineering- Charge at all levels. The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Finishing walls with textured interior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 Sq.m) over and including priming coat of exterior primer applied @ 2.20kg/10 Sq.m.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

SH: WATERPROOFING AND MISCELLANEOUS WORK Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying (a) First layer of slurry of cement @ 0.488 kg/Sq.m mixed with water proofing cement compound @ 0.253 kg/ Sq.m. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/Sq.m mixed with water proofing cement compound @ 0.126 kg/Sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.,leakage testing by ponding etc complete.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing and applying waterproofing treatment with a 3mm thick polymer-modified Bituminous membrane of Approved make. Atactic Poly-Propylene (APP) based with UV resistant, ground chemical resistant, high melting points, flexible and elastic with high adhesive strength. The membrane shall be reinforced with nonwoven polyester reinforcement of a minimum of 160 gm/Sq.m including carving the corner by torch welding over the primer with the overlap of 100 mm and appropriately pressing the membrane to remove any entrapped air. The termination of the membrane at 30 cm above the vertical wall.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing ,supplying and applying Chemical crystalline of approved make for waterproofing of water tank.The chemical should be mixed with mortar made of fine aggregate and cement on the concrete floor/Surface. Precautions should be taken such that there is no water or wetness seen on the slab while applying the mix. The mix has to be applied on the wall and the water tank has to be left to curing for a minimum of 24 hrs without any activities. After curing, water has to be filled in for observation for a minimum of 24 hrs to assure a leak proof finish as per the manufacturer specifications approved by the engineer in charge , including cost and conveyance of all material to site, lead, lift, and hire charges for scaffolding, labour charges etc....

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing rebar.Embedment depth as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed in hammer drill, diamond coring holes , including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. (The above work shall be carriedout by an agency having sufficient experience. Only skilled and experienced persons shall be employed for this purpose.) For fixing 8mm Dia bar with a hole dia of 10-12 mm. (Excluding the cost of reinforcement )

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing rebar.Embedment depth as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed in hammer drill, diamond coring holes , including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. (The above work shall be carriedout by an agency having sufficient experience. Only skilled and experienced persons shall be employed for this purpose.) For fixing 10mm Dia bar with a hole dia of 12- 14 mm. (Excluding the cost of reinforcement )

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing rebar.Embedment depth as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed in hammer drill, diamond coring holes , including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. (The above work shall be carriedout by an agency having sufficient experience. Only skilled and experienced persons shall be employed for this purpose.) For fixing 12 mm Dia bar with a hole dia of 14-16 mm. (Excluding the cost of reinforcement )

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing rebar.Embedment depth as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed in hammer drill, diamond coring holes , including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. (The above work shall be carriedout by an agency having sufficient experience. Only skilled and experienced persons shall be employed for this purpose.) For fixing 16mm Dia bar with a hole dia of 20mm. (Excluding the cost of reinforcement )

Providing and supplying heavy duty injection adhesive for rebar / anchor rod fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing rebar.Embedment depth as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed in hammer drill, diamond coring holes , including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels. (The above work shall be carriedout by an agency having sufficient experience. Only skilled and experienced persons shall be employed for this purpose.)For fixing 20mm Dia rebar / anchor rod with a hole dia of 25mm. (Excluding the cost of reinforcement/ anchor rod )

SH: INTERIOR WORKS Providing and fixing 20mm thick stone cladding of approved,quality and material over finished surfaces of walls using approved qulaity adhesive in all heights and levels as per the approved drawings and direction of Engineer-In-Charge. The exposed surface shall be finished with 100% Aliphatic Polyurethane (PU) coating. Sample shall be approved prior to procurement. The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Purchase Price : Rs. 1484 Per Sqm (Excluding GST ) Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor

Providing and Fixing of approved colour & design, Vinyl mix wall covering with paper backing,220 to 250 gsm- with recommended adhesive of approved make with fire retardant properties .Cladding on the partition wall or any recommended surface with base preparation as per the instrutions of Engineer in charge. The wall paper has to be approved by the Engineer-in-Charge before executing the work. The rate shall include all in fibre tape, proprietary make jointing compound, cutout for electrical sockets and all required materials, providing & removing of necessary scaffolding work etc. complete as per standards, specification and as directed by Engineer-in-charge. Warrenty - 2 years after installation. The purchase price of wallpaper Rs. 376/ Sqm . (excluding GST) .Any deviation plus or minus in the purchase (excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor. The above work shall be carried by an agency having sufficient experience in installation of wall paper and only skilled and experienced persons shall be employed for this purpose.

Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood.50x50 mm (base and height)

Supply and Installation of Exterior HPL 6mm thick Exterior grade F- Quality panels of make, shade , standard size with both side decor as approved by Engineer in charge. Exterior panels shall high-pressure be laminates (HPL) as per EN 438-6, type EDF ); Panels shall be [double hardened including acrylic polyurethane resin which is thermally cured under high pressure conforming to European norms with CE Mark on each and every Panel as per EN 438-7 with proven 3rd party certification with weather protection and excellent sustainability against UV, weathering, working in Heat Resistance range of -80 to Installation panels for 180. of Exterior facades and also soffils, shall be done by approved Rivets (with Fixed and Sliding Points) with minimum recommended, Aluminum T sec tion of 75x37x2.8 mm thick and L section 30x30x2.8mm thick held by Wall Bracket with Wind load and Dead load slot as per design, anc hored by standard equivalent fasteners Thermal or make anchor along with Separator. Installation of Exterior Panels shall be done us ing Rear Ventilated Principles only, which is to be ensured by providing ventilation gap minimum 200 cm2 per Meter (for free flow of air behind the taçade) for the façade and using the framework with no horizontal section. The rate shall include cost and conveyanc e of all materials, labour charges, lead, lift As per standards, specification and directed by the Engineer-in-charge. Price: Basic 3875/Sqm, The purchase price (excluding GST) of HPL panel is mentioned in basic price and any deviation plus or minus in the purcha se price will be adjusted ( paid extra or deducted) at the time of billing. The work shall be executed as per manufacturers specifications by a specialised agency having sufficient experience in similar work and should ensure a warranty for any defective installation, material for a period of 5 years from the date of completion of said work.

Providing and fixing Designer fluted veneer of 4mm thckness over 6mm marine ply screwed and supported over aluminium frame work formed out of 50x25mm 1.2mm thk sections at 600mm c/c. The fluted veneer must be polished with melamine finish to match the interior finishes. The cost to include making of groove, cutouts for electrical, data etc. as detailed. Basic rate of veneer shall be Rs. 1076/Sqm of finish Ash

Providing and fixing Wash counter unit made of 17mm multiwood for boxing and shutter works finished with 1 mm laminate for shutters and outer surfaces , inside to be lined with 0.8mm liner laminate .Top to be laid with granite 20mm thick, edges to be champhered. All neccessary hardwares and accessories like Soft close hinges, handles and other fittings should be provided as per the design and drawings DFI/CIAL-G/01/TEN/INT/COT-A/302 .The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Purchase Price (Excluding GST ) for 1mm laminate :Rs.470 per Sqm , 0.8mm laminate : Rs. 303 per Sqm Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor

Providing and fixing Wash counter unit made of 17mm multiwood for boxing and shutter works finished with 1 mm laminate for shutters and outer surfaces , inside to be lined with 0.8mm liner laminate .Top to be laid with granite 20mm thick, edges to be champhered. All neccessary hardwares and accessories like Soft close hinges, handles and other fittings should be provided as per the design and drawings DFI/CIAL-G/01/TEN/INT/COT-B/303 .The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge. Purchase Price (Excluding GST ) for 1mm laminate :Rs.725 per Sqm , 0.8mm laminate : Rs. 303 per Sqm Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor

Supplying and fixing wall to wall shower enclosure (Width 2500mm & Height 2100mm) with fixed toughened glass and door of size 750 x2100mm . Glass partitions using 10mm thick Toughened glass with necessary with silicon magnetic glass beading ,hardware fittings in Chrome finish with 1 Top Channel, 1 Wall Profile, 2 Magnet Profile, 1 Damn strip on the bottom, 1 fixed panel glass as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware.The rate is inclusive of all material ,labour,accessories ,hardwares, scaffolding etc all complete. as approved by Engineer in charge.

Supplying and fixing L shape WC enclosure (Width 1200+1500mm & Height 2100mm) with fixed toughened glass and door of size 750 x2100mm . Glass partitions using 10mm thick Toughened glass with necessary with silicon magnetic glass beading ,hardware fittings in Chrome finish with 1 Top Channel, 1 Wall Profile, 2 Magnet Profile, 1 Damn strip on the bottom, 1 fixed panel glass as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware.The rate is inclusive of all material ,labour,accessories ,hardwares, scaffolding etc all complete. as approved by Engineer in charge.

Providing and fixing in position mirror panelling with 6mm thick BWP ply backing fixed to a framework consisting of plywood sections as required. It shall have appropriate edge framing as required. The cost to include all materials, labour, wastages, lead, lifts, necessary staging/scaffolding, cutting, necessary hardware, tools and machinery, other related works, including provision for all services works complete as per drawings, specifications and as directed by the Engineer in charge

Providing & fixing 9 mm thick BWP grade ply confirming to IS- 710 on existing framework using approved size screws at every 600 mm center to center at all levels as per drawing.The ply shall be fixed in correct line and level as per drawing. The rate shall include the cost & conveyance of all materials, labour charges,levelling, lead, lift , cutting any shapes , provisions for electrical, networking fixtures wherever required, etc complete as directed by Engineer in Charge at all levels. Framework will be paid under revelant item.

Supply and fixing of Main/Sheer curtain and sttitch it as pleated style , install it in a Heavy Duty M track(Brand-Slide Impex) with side cap,Noice less wheel Runner,First Quality PVC pull batten.(The purchase price of material - Rs. 500 / Mtr for 1.4 m wide cloth )( Pleates per meter- 14 and GSM -225).The rate is inclusive of cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Any deviation plus or minus in the Purchase Price (Excluding GST) will be adjusted (paid extra / deducted ) while making payment to the contractor

Providing and fixing in-position laminate finish ledge made of 18mm thick sandwiched plywood to profile and shape as per the detail drawing. The ledge shall be supported with necessary framework as per the detail drawing.

Providing and fixing in position medium duty FRP manhole cover and frame of size 90 cm x 60 cm and class B-125 of required shape and approved quality for inspection chamber / manhole / gulley trap / and other required places as per the design and drawings.The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineerin-charge.

Providing and fixing in position medium duty FRP manhole cover and frame of size 60 cm x 60 cm and class B-125 of required shape and approved quality for inspection chamber / manhole / gulley trap / and other required places as per the design and drawings.The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineerin-charge.

Providing and fixing in position medium duty FRP manhole cover and frame of size 60 cm x 60 cm and class C 250 of required shape and approved quality for inspection chamber / manhole / gulley trap / and other required places as per the design and drawings.The rate shall include cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineerin-charge.

SH : SANITARY FIXTURES & FITTINGS Providing and fixing white vitreous china wall mounted type water closet (European type) with soft close duroplastic seat and lid of approved make and model, etc. complete, including cost and conveyance of all materials, labour charges, lead, lift, fixing to the frame of concealed flush tank, cutting and making good the walls and floors wherever required, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose. (The Purchase Price of WC pan with soft close seat and lid including all acessories shall be taken as Rs. 15250/- ( Excluding GST ) and any deviation plus or minus in the Purchase Price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor).W.C. pan with white soft closing duroplastic seat and lid

Providing and fixing white vitreous china wall mounted type water closet (European type) with soft close duroplastic seat and lid of approved make and model, etc. complete, including cost and conveyance of all materials, labour charges, lead, lift, fixing to the frame of concealed flush tank, cutting and making good the walls and floors wherever required, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. (The purchase price of WC pan with soft close seat and lid including all acessories shall be taken as Rs. 21413/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.W.C. pan with white soft closing duroplastic seat and lid

Providing and fixing Concealed Flushing Cistern with full frame for EWC with dual flushing system 3 / 6 litres with all accessories, actuator plate of approved make and model etc. complete including cost and conveyance of all materials, labour charges, lead, lift, cutting and making good the walls wherever required, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. (The purchase price of flushing cistern including all acessories shall be taken as Rs. 4140/- ( Excluding GST ) and purchase price of actuator plate including all acessories shall be taken as Rs. 3600/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing white vitreous china Wall Hung Urinal with built-in sensor (DC Type), of approved size with all accessories to provide satisfactory functioning, including necessary wall cutting / chasing and making good, waste connection and clamps, including all fittings as required for urinal flushing etc. complete, cost and conveyance of all materials, labour charges, lead, lift, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. (The purchase price of Wall Hung Urinal with built-in sensor (DC Type) including all acessories shall be taken as Rs. 51370/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing Counter Top Wash Basin 600 x 380 x 70 mm, or approved size and quality, 32 mm CP Brass waste assembly, 15 mm C.P. brass mixer taps, including cutting and making good the walls and floors wherever required, cost and conveyance of all materials, labour charges, lead, lift, etc. complete, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. (The purchase price of counter top wash basin including all acessories shall be taken as Rs. 10944/-,( Excluding GST ) waste coupling Rs. 1955/- ( Excluding GST ) and 15 mm CP bras mixer taps Rs. 8242/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.White Vitreous China Counter Top Wash Basin rectangular size with single 15 mm C.P. brass mixer tap

Providing and fixing Counter Top Wash Basin 600 x 380 x 70 mm, or approved size and quality, 32 mm CP Brass waste assembly, 15 mm C.P. brass mixer taps, including cutting and making good the walls and floors wherever required, cost and conveyance of all materials, labour charges, lead, lift, etc. complete, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. (The purchase price of counter top wash basin including all acessories shall be taken as Rs. 15670/-( Excluding GST ) , waste coupling Rs. 1955/-( Excluding GST ) and 15 mm CP bras mixer taps Rs. 19850/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.White Vitreous China Counter Top Wash Basin rectangular size with single 15 mm C.P. brass mixer tap

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality and make including, cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP Brass 32mm size Bottle Trap including all acessories shall be taken as Rs. 840/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing C.P. Brass Health Faucet with chrome plated flexible tube 1.0 metre long with SS cup and wall hook etc, of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of C.P. Brass Health Faucet with chrome plated flexible tube including all acessories shall be taken as Rs. 2745/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing gloss white cast acrylic construction reinforced marble freestanding bath tub 1700 x 800 x 565 or nearest size with slip resistant surface, of approved quality and make, waste coupling, bath tub over flow with floor flange accessory pack, pop up waste, masonry / concrete supports, etc. complete including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of gloss white cast acrylic construction reinforced marble freestanding bath tub including all acessories shall be taken as Rs. 63894/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing gloss white cast acrylic construction reinforced marble freestanding Jacuzzi 1700 x 750 x 420 or nearest size with slip resistant surface, of approved quality and make, waste coupling,over flow with floor flange accessory pack, pop up waste, masonry / concrete supports, etc. complete including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of gloss white cast acrylic construction reinforced marble Jacuzzi including all acessories shall be taken as Rs. 105000/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing superior quality 15mm dia CP concealed diverter 4 way, of approved make and model, including cost and conveyance of all materials, labour charges, lead, lift, cutting and making good the walls and floors wherever required, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP concealed diverter 4 way including all acessories shall be taken as Rs. 9625/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing superior quality 15mm dia CP bath tub spout, of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP bath tub spout including all acessories shall be taken as Rs. 5160/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing superior quality CP Bath & Shower mixer set for Bathtub, of approved make and model, including cost and conveyance of all materials, labour charges, lead, lift, cutting and making good the walls and floors wherever required, testing and commissioning to the satisfaction of the Engineer-in-Charge as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP Bath & Shower mixer set including all acessories shall be taken as Rs.7950/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing C.P. brass Ceiling Mounted Over Head Shower with 15 or 20 mm inlet of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of C.P. brass Ceiling Mounted Over Head Shower including all acessories shall be taken as Rs. 4740/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.220 mm diameter

Providing and fixing CP Brass towel rail complete with brackets fixed to grips with CP brass screws with concealed fittings arrangement etc, of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP Brass towel rail including all acessories shall be taken as Rs. 2240/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.600 mm long towel rail with CP cup

Providing and fixing CP Brass towel ring complete with brackets fixed to grips with CP brass screws with concealed fittings arrangement etc, of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP Brass towel ring including all acessories shall be taken as Rs. 1350/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.CP towel ring with CP cup

Providing and fixing CP Brass towel rack complete with brackets fixed to grips with CP brass screws with concealed fittings arrangement etc, of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP Brass towel rack including all acessories shall be taken as Rs. 2600/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.600 mm long towel rack with CP cup

Providing and fixing CP brass toilet paper holder and accessories etc. complete of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP brass toilet paper holder including all acessories shall be taken as Rs. 305/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.C.P. brass

Providing and fixing CP Brass 120x120 mm size soap Dish Holder with CP concealed fittings and accessories etc. complete of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP Brass soap Dish Holder including all acessories shall be taken as Rs. 1400/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing glass shelves 8 mm thick with CP Brass frame of size 600x100 mm with all neccesary fittings and accessories etc. complete of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP Brass soap Dish Holder including all acessories shall be taken as Rs.1850 /- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing Liquid Soap Dispenser, aluminium / ABS body with chrome / black finish etc. complete with brackets fixed to grips with CP brass screws with concealed fittings arrangement etc. complete of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of Automatic Liquid Soap Dispenser including all acessories shall be taken as Rs. 2800/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing CP brass twin coat hook with concealed fittings arrangement etc. complete of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of CP brass twin coat hook including all acessories shall be taken as Rs. 600/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing and fixing C.P. brass long nose bib cock conforming to IS standards and weighing not less than 810 gms of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of C.P. brass long nose bib cock including all acessories shall be taken as Rs. 583/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points conforming to IS:8931 of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of C.P. brass angle valve including all acessories shall be taken as Rs. 1720/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points conforming to IS:8931 of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of C.P. brass angle valve including all acessories shall be taken as Rs. 712/-( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.15mm nominal bore

Providing and fixing Frame less mirror of superior glass complete with 6 mm with all four edges machine polished /bevelled and back side protected with safty filim and 4 mm thick BWP grade on walls with mirrorscrew(spacer) of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of 600x450 mm beveled edge mirror including all acessories shall be taken as Rs. 542/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose..

Providing and fixing uplasticised PVC connection pipe with brass unions : with C.P. brass screws and washers of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels.45 cm length,15 mm nominal bore

SUB HEAD - II : COLD / HOT / FLUSHING WATER SUPPLY (INTERNAL / EXTERNAL): Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.20 mm nominal inner dia Pipes

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.25 mm nominal inner dia Pipes

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.32 mm nominal inner dia Pipes

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.40 mm nominal inner dia Pipes

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.50 mm nominal inner dia Pipes

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.65 mm nominal inner dia Pipes

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.80 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.20 mm nominal outer dia Pipes Concealed work, including cutting chases and making good the walls etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.25 mm nominal outer dia Pipes Concealed work, including cutting chases and making good the walls etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.32 mm nominal outer dia Pipes Concealed work, including cutting chases and making good the walls etc.

Supplying,fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (Hot water) 22 mm dia

Supplying,fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (Hot water)28 mm dia

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal inner dia Pipes External work

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal inner dia Pipes External work

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 32 mm nominal inner dia Pipes External work

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 40 mm nominal inner dia Pipes External work

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm nominal inner dia Pipes External work

Providing and fixing UPVC ASTM Sch 40 pipes, for cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 65 mm nominal inner dia Pipes External work

Providing, fixing, jointing and testing, heavy quality Brass ball valve single piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: as per direction of Engineer in Charge.20 mm nominal bore

Providing, fixing, jointing and testing, heavy quality Brass ball valve single piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: as per direction of Engineer in Charge.25 mm nominal bore

Providing, fixing, jointing and testing, heavy quality Brass ball valve single piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: as per direction of Engineer in Charge 32 mm nominal bore

Providing, fixing, jointing and testing, heavy quality Brass ball valve single piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: as per direction of Engineer in Charge 40 mm nominal bore

Providing, fixing, jointing and testing, heavy quality Brass ball valve single piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: as per direction of Engineer in Charge 50mm nominal bore

Providing, fixing, jointing and testing, heavy quality Brass ball valve single piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: as per direction of Engineer in Charge 65mm nominal bore

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from PVC pipes-10 KGF/CM2 & uPVC sheet (600 mm long) 4” (110mm) dia PVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from PVC pipes-10 KGF/CM2 & uPVC sheet (600 mm long) 6” (160mm) dia PVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) with one end astm flange 1" (25 mm) dia UPVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) with one end astm flange 1.5" (40 mm) dia UPVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) with one end astm flange 2” (50mm) dia UPVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) with one end astm flange 2 ½” (65mm) dia UPVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) with one end astm flange 3 " (80 mm ) dia UPVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) with one end astm flange 4” (100mm) dia UPVC

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-80 pipes & uPVC sheet (600 mm long) with one end astm flange 6” (150mm) dia UPVC

Providing material and labour for fixing in position PVC pipe sleeves - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam before concreting. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while laying reinforcement and shuttering, sleeves shall not get displaced while concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Measurement shall be taken up to two decimal. (minimum 0.01 mt.). Rate shall be inclusive of removal of sleeves before water proofing or grouting. For all floors/ all levels/ all heights. Location of sleeve shall be approved by Engineer in charge. 160 MM DIA

Providing material and labour for fixing in position PVC pipe sleeves - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam before concreting. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while laying reinforcement and shuttering, sleeves shall not get displaced while concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Measurement shall be taken up to two decimal. (minimum 0.01 mt.). Rate shall be inclusive of removal of sleeves before water proofing or grouting. For all floors/ all levels/ all heights. Location of sleeve shall be approved by Engineer in charge. 110 MM DIA

Providing material and labour for fixing in position PVC pipe sleeves - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam before concreting. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while laying reinforcement and shuttering, sleeves shall not get displaced while concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Measurement shall be taken up to two decimal. (minimum 0.01 mt.). Rate shall be inclusive of removal of sleeves before water proofing or grouting. For all floors/ all levels/ all heights. Location of sleeve shall be approved by Engineer in charge. 90 MM DIA

SUB HEAD - III : INTERNAL DRAINAGE (SOIL, WASTE & VENT) Providing, jointing, testing and fixing UPVC Soil, Waste & Vent pipework conforming to IS : 13592 Type B and UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offset and other specials, jointing done with solvent cement for fittings and specials, fixing inside sunken slab / suspended below RCC slab for concealed soil and waste lines, making proper connection and also pipes may be laid / fixed in sunken floors, under hung from ceiling. The pipes laid in sunken floor shall be supported with cement concrete (1:2:4) blocks and under hung lines shall be supported from slab with universal clamps. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. (All GI pipe supports to hold the pipes is included in this item). 75 mm dia Type B

Providing, jointing, testing and fixing UPVC Soil, Waste & Vent pipework conforming to IS : 13592 Type B and UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offset and other specials, jointing done with solvent cement for fittings and specials, fixing inside sunken slab / suspended below RCC slab for concealed soil and waste lines, making proper connection and also pipes may be laid / fixed in sunken floors, under hung from ceiling. The pipes laid in sunken floor shall be supported with cement concrete (1:2:4) blocks and under hung lines shall be supported from slab with universal clamps. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. (All GI pipe supports to hold the pipes is included in this item). 110 mm dia Type B

Providing, jointing, testing and fixing UPVC Soil, Waste, Vent & Rain Water pipework conforming to IS : 13592 Type B and UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offset and other specials, jointing done with solvent cement for fittings and specials, fixing at wall / ceiling level supported by galvanized steel slotted rails, threaded rods, clamps, hangers etc., making proper connection etc for duct and ceiling suspended soil and waste lines. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. (All major MS / GI supports to hold the stack is included in this item). 75 mm dia Type B

Providing, jointing, testing and fixing UPVC Soil, Waste, Vent & Rain Water pipework conforming to IS : 13592 Type B and UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offset and other specials, jointing done with solvent cement for fittings and specials, fixing at wall / ceiling level supported by galvanized steel slotted rails, threaded rods, clamps, hangers etc., making proper connection etc for duct and ceiling suspended soil and waste lines. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. (All major MS / GI supports to hold the stack is included in this item). 110 mm dia Type B

Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 of class 3 ( 6kg/cm2) as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation for cocealed drain lines. (All major MS / GI supports to hold is included in this item) 25 mm dia 6 kg/cm2 (Class III ) -Spout point

Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 of class 3 ( 6kg/cm2) as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation for cocealed drain lines. (All major MS / GI supports to hold is included in this item) 40 mm dia 6 kg/cm2 (Class III )

Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 of class 3 ( 6kg/cm2) as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation for cocealed drain lines. (All major MS / GI supports to hold is included in this item) 50 mm dia 6 kg/cm2 (Class III )

Providing, fixing, jointing, testing and commissioning UPVC (Class III) Rain water downtake pipe conforming to IS:4985 cut to required lengths including all necessary fittings and specials.UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offsets and other specials. Fixing at wall/ceiling level supported by galvanized steel slotted rails, threaded rods, clamps, hangers etc. Making proper connection with cement solvent joint as per BIS / manufacturer. Cutting, chases / holes in floors / walls / slab and making good wherever required. (All major MS / GI supports to hold the stack is included in this item). 110 mm dia. 6 kg/cm2 (Class III)

Providing, fixing, jointing, testing and commissioning UPVC (Class III) Rain water downtake pipe conforming to IS:4985 cut to required lengths including all necessary fittings and specials.UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offsets and other specials. Fixing at wall/ceiling level supported by galvanized steel slotted rails, threaded rods, clamps, hangers etc. Making proper connection with cement solvent joint as per BIS / manufacturer. Cutting, chases / holes in floors / walls / slab and making good wherever required. (All major MS / GI supports to hold the stack is included in this item). 160 mm dia. 6 kg/cm2 (Class III)

Providing and fixing UPVC/SWR trap (Multi trap) of self cleaning design as per IS:13592 : 1992 complete including cost of cutting and making good the cutouts in walls and floors etc.including cutting and making good the walls and floors wherever required complete. 100 mm inlet and 75 mm outlet.

Providing and fixing Heavy Class cockroach free SS floor grating of approved design and make, including setting in floor with cement mortar / tile adhesive / epoxy joint filler to match with floor finish, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. (The purchase price of Heavy Class cockroach free SS floor grating including all acessories shall be taken as Rs. 500/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose. Size 125 mm X 125 mm or nearest size

Providing, fixing, jointing, testing andcommissioning at site in position Concealed floor trap (4” UPvc fabricated Multi Trap, with Stainless Steel Square frames (150x150mm) SS (304), Rubber Seal and flat round cover with screw. etc. complete in all respects. (The purchase price of Heavy Class cockroach free SS floor grating including all acessories shall be taken as Rs. 775/- ( Excluding GST ) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose.

Providing, fixing, jointing, testing and commissioning at site in position SS 304 grade Floor Drain (30x30x8 cm ) .The purchase price of floor drain including all acessories shall be taken as Rs. 6100/-(Excluding GST) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). Trough using 1.2 mm thick SS 304 grade ,Grating using 2 mm thick SS 304 grade,per specifications and as directed by the Engineer in Charge

Providing, fixing, jointing, testing and commissioning at site in position SS 304 grade Floor Drain (60x30x8 cm ) .The purchase price of floor drain including all acessories shall be taken as Rs. 11650/-(Excluding GST) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor). Trough using 1.2 mm thick SS 304 grade ,Grating using 2 mm thick SS 304 grade,per specifications and as directed by the Engineer in Charge

Providing, Supply, installation,testing and commissioning of UPVC Oil Waste system conforming to DIN-EN-12056 & DIN-1986-100 fittings.The pipes, fittings and seals can operate continuously at 90°C / 194°F (95°C/203°F Intermittently). They are suitable for the drainage of chemically aggressive wastewater with pH value of 2 (acidic) to 12 (basic) (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offSet and other specials. Jointing shall be done with pushfit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with pushfit rubber joints. Pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. 50 mm Dia

Providing, Supply, installation,testing and commissioning of UPVC Oil Waste system conforming to DIN-EN-12056 & DIN-1986-100 fittings.The pipes, fittings and seals can operate continuously at 90°C / 194°F (95°C/203°F Intermittently). They are suitable for the drainage of chemically aggressive wastewater with pH value of 2 (acidic) to 12 (basic) (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offSet and other specials. Jointing shall be done with pushfit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with pushfit rubber joints. Pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. 75mm Dia

Providing, Supply, installation,testing and commissioning of UPVC Oil Waste system conforming to DIN-EN-12056 & DIN-1986-100 fittings.The pipes, fittings and seals can operate continuously at 90°C / 194°F (95°C/203°F Intermittently). They are suitable for the drainage of chemically aggressive wastewater with pH value of 2 (acidic) to 12 (basic) (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offSet and other specials. Jointing shall be done with pushfit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with pushfit rubber joints. Pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. 110mm Dia

Providing, Supply, installation,testing and commissioning of UPVC Oil Waste system conforming to DIN-EN-12056 & DIN-1986-100 fittings.The pipes, fittings and seals can operate continuously at 90°C / 194°F (95°C/203°F Intermittently). They are suitable for the drainage of chemically aggressive wastewater with pH value of 2 (acidic) to 12 (basic) (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offSet and other specials. Jointing shall be done with pushfit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with pushfit rubber joints. Pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. Multi floor trap/ P trap-110 mm Dia

Supplying, Installing, Testing and Commisioning at site in position PVC Vent cowl with SS jali proper supports for vertical and horizontal drainage lines complete in all respects. 160 mm dia

Supplying, Installing, Testing and Commisioning at site in position PVC Vent cowl with SS jali proper supports for vertical and horizontal drainage lines complete in all respects. 110 mm dia

Supplying, Installing, Testing and Commisioning at site in position PVC Vent cowl with SS jali proper supports for vertical and horizontal drainage lines complete in all respects. 75 mm dia

SUB HEAD - IV : EXTERNAL SEWAGE/ STORM WATER DRAINAGE. Providing, fixing, jointing, testing and commissioning UPVC (Class III) Soil, Waste & Rain Water Drainage pipes conforming to IS:4985 cut to required lengths including all necessary fittings and specials. UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, reducers and other specials including trenching, refilling (Up to 1.5 mtr depth)& testing of joints etc. Making proper connection with cement solvent joint as per BIS / manufacturer, complete as per direction of Engineer in Charge. External work 75 mm dia 6 kg/cm2 (Class III )

Providing, fixing, jointing, testing and commissioning UPVC (Class III) Soil, Waste & Rain Water Drainage pipes conforming to IS:4985 cut to required lengths including all necessary fittings and specials. UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, reducers and other specials including trenching, refilling & testing (Up to 1.5 mtr depth)of joints etc. Making proper connection with cement solvent joint as per BIS / manufacturer, complete as per direction of Engineer in Charge. External work 110 mm dia 6 kg/cm2 (Class III )

Providing, fixing, jointing, testing and commissioning UPVC (Class III) Soil, Waste & Rain Water Drainage pipes conforming to IS:4985 cut to required lengths including all necessary fittings and specials. UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, reducers and other specials including trenching, refilling (Up to 1.5 mtr depth)& testing of joints etc. Making proper connection with cement solvent joint as per BIS / manufacturer, complete as per direction of Engineer in Charge. External work 160 mm dia 6 kg/cm2 (Class III )

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 110 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 160 mm dia

Supplying, fixing, testing and commissioning to the satisfaction of the Engineer-in-Charge of PVC gully trap of size 160 x 110 mm and CI grating 150 x 150 mm size and water tight C.I. cover with frame of 300 x 300 mm size (inside), the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg (CI MH cover and frame as per IS:1726) single sealed of size conveying to size the above mentioned items and constructing 30cm x 30cm internal size gully trap shamber and depth upto 60cms, 115 thick brick wall in CM 1:6 on a foundation of PCC 1:4:8, 100 mm thick, plastering inside with CM 1:3, 12mm thick with a neat flushing coat and conveying to site, cleaning, installing and testing approved make PVC Gully Trap with 110mm outlet, surrounding with CC 1:1.5:3, 150x150mm, top with CI Grating, above the PVC Gully Trap, and light duty CI cover and frame over the chamber, including cost of all materials, etc. complete as per approved drawing and as directed by the Engineer-in-Charge. 160 x 110 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supply, installation and commisioning of Grease separator made of polyethylene as per EN 1825 and DIN 4040-100, proven Stability of 50 years; for below ground installation; overall dia. of 1320 mm.; with ventilation provision; emptying via suction line DN 65 PN 10; counter Hinge with fire hose quick coupling 758 and 2½" blank cap; filling device with solenoidal valve for automatic refiling; with automatic hydromechanical internal cleaning with high pressure pump of nominal pressure 175 bar and flow volume 11.6 1/min. with storage tank for indoor installation; with grease level sensor with alarm device having cable length of 20 metres, with high pressure hose for connecting the high pressure pump to high pressure cleaning head inside the grease separator and satisfy reaction to fire class A.. The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced person shall be employed for this purpose. Standard odour tight top cover of 600 mm dia. clear opening; frame made of concrete material and cover made of cast iron; without raising tube; for a load class A15 according to EN 124 Inlet and outlet dia.: DN 150 Nominal Size: NS 5.5 Grease Storage: 230 litres, Sludge Storage: 570 litres, Overall Capacity: 1465 litres

Ravindranath Constructions Pvt Ltd (BID ID -2213807)