Providing FSSM Co Treatment System Capacity 42.90 KLD along with existing STP for Mandi Town in Distt Mandi

Amount

Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work,blasting work,chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15 cm. layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing oof all surplus excavated soil as directed in all leads and lifts and soring/strutting timbering and dewatering where ever required to the entire satisfaction of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 cement : 3 coarse sand): 6 graded stone aggregate 40 mm nominal size) in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 cement : 3 coarse sand): 6 graded stone aggregate 20 mm nominal size) in all leads and lifts. Hand mixed concrete linning in bed : complete in all leads and lifts.

Hand mixed concrete linning on side slopes : complete in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand): 8 graded stone aggregate 40 mm nominal size) in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (1 cement : 5 coarse sand) : 10 graded stone aggregate 40 mm in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. complete in all respect.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform in all leads and lifts.

Extra allowances for form work in side slopes with in all leads and lifts

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Edges of slabs and breaks in floors and walls Under 20 cm wide in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand): 4 graded stone aggregate 20 mm nominal size) in all leads and lifts.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm in all leads and lifts.

in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, huttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm in all leads and lifts.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of entering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars in all leads and lifts.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1cement :3 sand )

Steel work welded in built up sections, trusses & framed work i/c cutting, hoisting & fixing in position & applying a priming coatof red paint :- In grating, framed, guards, bars, ladders, railing, brackets & similar works

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (i) Electric resistance or induction butt welded tubes

White washing with lime on undecorated wall surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt, dust and other foreign matters in all leads and lifts.

Boulder filling dry hand packed tightly under floors in all leads and lifts.

Providing and Fixing of Precast SFRC Manhole Cover with Frame conforming to IS-12592 (Part - I)-1998 with latest ammendments 560 mm dia in all leads and lifts. i) Medium Duty

Providing and laying Double Flanged (Screwed/Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 : complete in all leads and lifts. 250 mm dia

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement Mortar 1:4 within all leads and lifts.

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : within all leads and lifts.

20mm cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:4 (1 cement : 4 sand) within all leads and lifts.

Providing & fixing UV stabilised 6mm polycarbonate sheet, Multiwall polycarbonate sheets, bolts & nuts 8mmdia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc.The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured.They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. within all leads and lifts.

Providing and fixing 15 cm. wide 45 cm. overall semicircular G.I. Sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design within all leads and lifts.

Providing and fixing Ridges or Hips 60 cm overall with Poly Carbonate Sheet in roofing iron J or L hooks, bolts & nuts 6mm dia G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.

Providing and fixing galvanised M.S. wire gauge of I.S. gauge designation no. 85 g with wire of dia 0.56 mm complete with all accessories as required as per the direction of Engineer in Charges.

Laying, jointing and testing in trenches centrifugally cast (spun) ductile iron pipes 150 mm dia conforming to BIS 8329-2000 (latest with up to date amendments) in a length of 5.50 meters class K7 with cement mortor lining in side duty ISI marked including cost of Tyton (push or joints) fittings including testing of joints and rubber gasket (S&R quality) conforming to IS-92820-1989 (Earth work in trenches to be measured and paid for separetely) in all leads and lifts.

Providing and jointing tyton (Push on joints) to Ductile iron pipe 150 mm dia and fitting including testing of the joints, cost of rubber gasket (EDPM quality) conforming to IS 3382 latest edition/ ammendments complete in all respect within all leads and lifts and as per latest ammendments or edition

Providing and fixing all socket DI Tee/ Cross as per IS 8329 or letest additional amendments including carriage of material within all leads lifts complete in all respect. 150 mm dia

Providing and fixing of Cast Iron Sluice Valve of following dia mentioned below class PN 1.0 with Flange Table - 17 conforming to BIS : 14846-2000 or latest with upto date ammendments of BIR / KARTAR / PELICON make including cost of flanges with nut & bolts, rubber insertions washers (gasket) etc. as per specifications complete in all respect in all leads and lifts and to the entire satisfaction of Engineer - in - Charge.

250 mm diameter

150 mm dia

Providing and fixing Screen Gate (Manual Operation), MS with Epoxy Coated, MSEP Sluice Gate including all leads and lifts.

Providing and fixing Screen Channel (Manual Operation), screen inclined at 55 degrees, MS with Epoxy Coated, MSEP including all leads and lifts.

Providing, Supply and errection of Non Clog submersible pump as per the Curve chart & site conditions. The pumping machinery include automatice control pannel, main MCB, Voltmeter, Amperemeter, Power capacitor, Control MCB, Supply & motor side cable/NRV/Sluice valve/Common Header Job/Earthing and the all other required accessories/ components requirement as per latest IS code (latest edition and CPHEEO manual). with suitable application in all respects and to the entire satisfation of Engineer-in-Charge. Head 20 Mtr & Discharge :-1.5 LPS of (Single Phase)=6 Set

Providing and fixing of Sluice Valves and NRVs, Bends, 100mm, 150 mm, 250mm dia of Kirloskar/Leader make including all leads and lifts

Providing and fixing of Cables from motor to control Panel including all lead and lifts.

Errection and testing of all equipments i/c cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

Providing, Manufacturing, Supplying and Fixing of Fencing Panel of Size. 1.20 M X1.20 Meters fitted with Expended Metal Jali 25 X 25 mm mesh welded with M.S. angles for stand 40 x 40 x 5 MM including cutting, welding, painting with red oxide paint complete in all respect and as per with MS flat cover 25 X 5 MM M.S. hold fast made of M.S. angle 40 x 40 x 5 MM mesh panel of size 1.20 X 1.20 M fitting with expended metal mesh embended in cement concrete Pillars complete in all respect as per direction and to the entire satisfaction of the Engineer - in - Charge.

Dressing of bed and prepration of sub grade for linning in pick work complete in all respect.

Dressing of side slopes and prepration of sub grade for linning in pick work : complete in all respect.

Providing and fixing New generation energy saving & environmental friendly, long life, High-pressure die-cast aluminium housing Flood Light with toughened Glass cover. 50W LED of reputed make and other fittings etc.complete in all respect in all leads and lifts.

Providing and fixing Havells PVC insulated and PVC Round Sheathed, Multicore Annealed Bare Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 of 1.50 Sqmm complete in all respect in all leads and lifts.

GANTANTAR THAKUR (BID ID -591788)