SPECIAL REPAIR TO ROOF TREATMENT OF A WING AND PARAPET RCC JALI WALL OF MAIN BLDG AT PM KV NO. 2 AND OTHER SANCTION WORK UNDER THE AREA OF AGE B/R-II OF GE (ARMY) No. 1 JODHPUR

Amount

Demolition of brick / block or stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L for precast cement concrete Type C-0 1:3:6 (12.5mm graded aggregate) as in louvres and jallies, cement grill any type model of Zafri , 35mm thick (measured solid), set in cement mortar 1:6 fixed with PCC post, incld. all mouldings complete all as specified and directed.

Supply & laying of precast cement concrete1:3:6, type C-1 (by using 20mm graded stone aggregate) as in pillars (size 150 x 150 mm and 75-100 cm height) to provide support of RCC jallies, jointed with neat cement slurry, in CM 1:6, and including demolition of existing jallies and removed from MOD land, complete all as specified and as directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface even and smooth without using extra cement , complete all as specified and as directed. Note -Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures.

M&L Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over & including M&L single coat of chalk white complete all as specified and as directed.

Demolition of cement conc padding of water proofing treatment from padding taking down bituminious polythene sheets plaster ect overall thickness n.exc 200mm , cleaning of conc surface by wire brushes scrubbing down water and removing the dust debris etc. to a distance 50m but not exc 250m from site, complete all as directed

M&L for plain cement concrete 1:2:4 type B-0 (using 12.50mm graded stone agg) over roof for making good depression/ undulation to match the existing as filling in depression of roof slab etc, complete all specified and directed.

M&L for carrying out water proffing treatment for roofs in the following stages:- (i) Rendering 10mm thick in cement mortar (1:4), mixed with integral water proofing liquid allas per manufacturer's insturctions over concrete surfaces finished even and smooth with out using extra cement Note (WPC shall be measured separately and paid for under respective item of schedule) (ii) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied water proofing membrane having solid content of 55% formulated with PU hybrid polymers and reinforcing acrylic fibers and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat 6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and wate r3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/ 10 sqft in two coats (10-12) hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongational break of 350% crack bridging ability of 2.5mm @650 microns thickness resists positive hydrostatic pressure of up to 10 bars. The material shall be applied with bursh or roller, Also proper surface preparation along with covingat corners is must etc, complete all specified and directed. Note : The work shall be executed by the authorized applicator of the manufacturere only. Note: 1 The authorized applicator of manufacturere shall be approved by GE. 2. The color of final finish shall be decided by the GE.

Supply only integral water proofing compound (ISI marked).

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or credited to contractor complete all as specified and directed.

All as per item No 12.00 here-in-above, but size of pipe 20 mm bore, complete all as specified and directed.

S&F GI tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

All as per item No 14.00 here-in-above, but size of pipe 20 mm bore, complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 (using 20mm graded stone agg) as in bed for OH tanks, roof kerb rounded or chamfered on edges to match the existing , complete all as specified and directed.

S&F in replacement 1000 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed, including dismantling old u/s existing tank, complete all as specified and as directed.

Surface excavation n. exc. (not exceeding 30 cm deep and avg 15 cm deep) and getting out in sof/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil, complete all as specified and as directed .

M&L for Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in soils complete all as specified and directed.

M&L for Removal of excavated material soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Excavation over areas n. exc.1.5m deep and getting out in hard/dense soil complete all as specified and as directed.

Excavation over areas exc.1.5m deep and n.exc 3.00m deep and getting out in hard rock complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 type D-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed .

M&L for 40 mm thick cement concrete type B-0 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in damp proof course to horizontal or vertical surfaces including nessary formwork (using WPC paid seperately in respective item) etc complete all as specified and as directed.

Use and waste Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat, complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) and similar works fair finished surfaces of concrete complete all as specified and as directed.

M&L for formwork to Edges of concrete flats, treads, breaks in floors.concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC band in walls, sloping and similar work for fair finished surfaces. Rough finished surfaces of concrete flat, complete all as specified and as directed.

Use and waste for formwork to faces of walls,retaining walls, abutments,parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and as directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as Beams, cantilevers, roof beam, floor beam, bressummers, lintels over 1.5m span, complete all as specified and as directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as in footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as walls, retaining walls, basement walls, ballast walls and the like, any thinkness , above top of footing, including attached pilasters and buttresses etc, complete all as specified and as directed.

S&F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 6 to 8mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 5 dia and over upto and including 10 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M&L for 20mm dia MS rod as in steps/rungs etc complete including cutting,bending to shape as required.complete all as specified and directed.

M&L for Brickwork with fly ash old size burnt bricks, straight or curved on plan exc 6m mean radius, built in and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) in foundation, above plinth level upto two stories in all shapes and sizes all as specified and as directed by Engr-in-charge.

M&L for 15 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed. Note -Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures.

M&L for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM (1:4) surface finished even and smooth without using extra cement complete all as specified and directed. Note -Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures.

M&L for 10 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM (1:4) surface finished even and smooth with WPC ( without using extra cement) etc, complete all as specified and directed. Note -(i) Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures. (ii) WPC shall be paid and measured sapartively.

M&L for 5 mm thick rendering in cement mortar 1:4 on concrete ceiling surfaces / sunsheds / facia / RCC chajja, finished even and smooth without using extra cement, complete all as specified and directed. Note -Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures.

M&L for preparation of new plastered or unplastered surfaces of wall and applying with 1.5-2.0 mm thick wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper (shade or tint as approved by GE) over & including one coat of primer on walls complete all as specified and as directed Note -i)- Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures. ii)- Paint shall be in one or more colours/ shades all as approved by GE.

All as per item No. 43.00 here-in-above, but as on ceiling

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces over and including 1.5-2 mm thick wall care putty etc, complete all as specified and as directed.

Earth filling under floors or in foundations including watering and consolidation, spreading and levelling in layers n.exc. 25cm thick and well ramming including watering as rerquired etc, complete all as specified and directed.

M&L for 100mm thick Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L Hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, compacting with power roller, complete all as specified and as directed.

M&L for 100mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate), as in sub base of floor, complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-1 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L for non-skid coloured ceramic tiles joint free 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.16 Sqm but n exc 0.72 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:6) for laying in floors finishing ,complete all as specified and directed.

M&L for glazed colour ceramic tiles (premium quality) of area of each tile exc. 0.36 sqm but n. exc. 0.72 sqm on wall of thick 8-10mm as per IS 13712 grade II , as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L for 15 to 18 mm thick udaipur green marble machine cut on cill, shelves, cooking plateform (table rubbed and polished) best quality as per sample, including & over 10 mm thick screeding in CM1:4 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed.

M&L for 18-20mm thick Black Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, slabs for oval type WHB, sink, cooking platforms and like including & over 15 mm thick screeding in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, providing suitable dia hole in the slab for the gas pipe / water supply pipes etc, complete all as specified and as directed.

M&L Machine cut kota stone slab flooring using 20 to 25mm thick slabs,as in shevles (single piece), shelf, cub board, almira, partation etc and other places, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including rounding to edges of kota stone fixed with cement mortar 1:4 complete all as specified and as directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantFactory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length etc, complete all as specified and as directed. Note: (a)-For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (b)- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc, complete all as specified and as directed.

S&F 40mm thick 2nd class hardwood ,Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats etc, complete all as specified and as directed.

M&L for Plain, solid, straight, chowkats and frames of 2nd class hardwood, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc, complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surface of any description, over 10cm width or girth, not otherwise described and applying french polishing including a coat of wood fillet on new works with two or more coats etc, complete all as specified and as directed.

S&F anodised aluminium frame powder coated (minimum thickness of powder coating 50 micron) for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified & as directed.

S&F anodised aluminium door / window / ventilator shutters powder coating of any colour (Thickness of powder coating not less than 50 micron) , aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

S&F pre powder coated aluminium decogrill all as per sample fixed to aluminium framework of windows & ventilators, complete all as specified and directed.

S&F 5.5 mm thick tinted plan / forsted / back glass exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading, complete all as specified and directed.

S&F mortice latch with two loovers (Vertical type) mild steel body 100mm long and fixed, complete all as specified and directed.

S&F of Box type steel ventilator with top hung shutter including hinges with steel handle, and steel peg stay, complete with glazing bars, complete all as specified and as directed.

All as per item No. 66.00 here-in-above, but without glazing

Supply and fabrication of Mild steel guard bars, grills, grating, and similar work and welded to window frames, door frames (made up of angle), balcony railing confirming to FE 290, gde E-165 etc , complete all as specified and directed. Note :- Guard bars shall be factory welded & given one shop coat of red oxide or zinc chromate primer. Cost of factory welding & Shop coat of primer is deemed to be included in quoted rates.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm, complete all as specified and as directed.

S&F powder coated aluminium anodised tower bolt 100 mm size, complete all as specified and directed.

S&F 75 mm size powder coated aluminium handle fixed to windows, complete all as specified and directed.

S&F of Stainless steel butt hinges medium weight, cold rolled of size 100 mm size, complete all as specified and directed.

S&F 200 mm long aluminium anodised tower bolt of extruded section, complete all as specified and directed.

S&F 150mm long aluminium alloy anodised handle extruded section, complete all as specified and directed.

S&F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed.

S&F of stainless steel peg set of five fixing with wall complete all as specified and directed.

M&L Figured glass 4.00 mm thick, pin head type and glazing with putty in square not exceeding 0.50 Sqm in each pane etc, complete all as specified and as directed.

S&F of vitreous ware wash down water closet [Pedestal Pattern], white [ETWC] including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap connecting to drain pipe and flushing pipe etc.,& provision of cement concrete making good to as existing floor etc, complete all as specified and as directed.

S&F of vitreous china squatting Pan, Orissa Pattern of size 580X440mm white with integral foot rests and cast iron `P' or `S' trap front or back fixed in repairs Including connection to trap etc and provision of cement concrete bedding and making good to floor etc, complete all as specified and as directed.

S&F of PVC valve less, syphonic action type, cistern, low level of 10 ltrs capacity, white with inlet, ball valve, float and handle including brackets, pipe of 32 mm dia including cuttings of floor / wall and making good in CM (1:3) and fiishig the surfaces to match with existing complete all as specified and as directed.

Supply, laying, testing & commissioning of 20 mm outer dia CPVC pipe,SDR-11, with all fitting (eblow, socket,tee with internal thread of brass) fixed to wall, ceiling or laid on floor / trenches, with CPVC solvent, complete all as specified and directed.

All as per item No. 81.00 here-in-above, but size 25 mm bore

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing , etc. and making good, cutting exceeding 20cm girth, complete all as specified and directed.

S&F of 15mm bore PVC connection for 600 mm long best quality with PTMT nuts at both ends with rubber washers, complete all as specified and as directed.

S&F of Wash Basins,Vitreous China pedestal Ivoery,flat back,size 550 x 400mm including brackets and cutting for and pinning in ends of brackets or erecting stand and fixed including fixing and supply of Waste fittings, brass, chromium plated etc, complete all as specified and as directed.

S&F 15mm bore swan nake pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified.

S&F of flush pipe polythylene of low or high density or PVC 32mm dia, for WHB etc, complete all as specified and as directed.

S&F Vitreous china urinal half stall type with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified and as directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed.

M&L for 5-6 mm thick bevelled edges high quality looking mirror fancy type fixed to wall with chromium plated screw with cup washers etc., complete all as specified and as directed.

S&F of CP bib taps 15mm dia, cast copper alloy fancy type, long body screwed for iron pipe or for brass ferrule , complete all as specified and directed.

S&F stop valve, 15 mm bore, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

S&F for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1000 mm long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed.

S&F of two way angle cock chromium plated fancy type 15 mm bore /size complete all as specified & directed.

S&F angle / stope valve, 15 mm bore, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

S&F of Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms) complete all as specified and as directed.

S&F coloured toilet paper holder, vitreous China, box type complete all as specified and as directed.

S&F of brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Supply & laying 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches of suitable size complete all as specified and as directed .

Supply & laying 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches of suitable size complete all as specified and as directed .

S&F of 75 mm outlet dia. of PVC (SWR) floor / nahani trap plain with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregates etc, complete all as specified and directed.

S&F of 110 mm outlet dia. of cast iron floor / nahani trap plain with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregates etc, complete all as specified and directed.

M&L for 150mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregates as in platform for water tank on roof, finished the surface even and smooth with WPC complete all as specified and directed.

Supply & laying jointing and testing 150mm bore reinforced conctete pipes class NP-2 laid and jointed in cement mortor 1:1 complete with collars or socket/spigot type laid jointed and haunching at side in cement complete all as specified and directed.

M&L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for 150 mm dia pipe complete all as specified and directed.

Supply & laying jointing and testing 150mm dia Salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and as directed.

M&L 50 mm thick PCC 1 : 3 : 6, type C1, (by using 20mm graded stone aggregate) for plinth pretection finishing even and smooth without using extra cement, Including expansion joint every three metre and change in direction and joint to be filled with sealing compound Gde A complete all as specified and directed.

S&F of framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

M&L for 7.5cms thick machine cut Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all as specified and as directed.

M&L for connecting 25 mm bore GI pipe from existing water supply line including necessary excavation , clamping making holes to existing pipe line, complete all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore and fixed, complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

M&L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLSH cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces as per existing finishes) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLSH PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, suitable for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed. Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates

All as per Sr. item No. 117.00 here-in-above, but suitable for One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per Sr. item No. 117.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable (FRLSH)including 2.5 sq mm PVC insulated unsheathed stranded copper conductor(FRLSH) for common earth wire for 5 pin 15 Amp socket outlet on independent board .

M&L for modular point wiring complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FR-LSH cable (RYBN) 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FR-LSH cable (Green) 1100 Volts grade as earth continuity wire connected to earth dolly and including modular sunken galvanized terminal boxes of same make of switch/ socket/ regulator with sleek and curvy cover plates, for mounting of modular switches, sockets, fan regulators etc, complete all as specified abd as directed.

All as per Sr. item No. 120.00 here-in-above, but suitable for One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per srl item no.120.00 here-in-before but with 2.5 sq mm FRLSH copper wire with 2.5 Sqmm FRLSH copper earth wire for indpendent 15 Amp point.

S&F Switch piano, flush type, single pole, one way,5/6 amps, 230 volts, complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way,15/16 amps, 230 volts, complete all as specified and directed.

S&F Socket, two-in-one, 3 /5 Pin, 5/6 Amp, flush type, 230 volts, complete all as specified and directed.

S&F Socket, two-in-one, 3/6 Pin, 6/16 Amp, flush type, 230 volts, complete all as specified and directed.

S&F Modular switch flush type single pole one way 6 Amp ISI Marked,1 module, complete all as specified and directed.

S&F Modular switch flush type single pole one way 16 Amp ISI Marked,1 module, complete all as specified and directed.

S&F Modular socket outlet 2 in 1, 3 pin, 6 amp flush type, 230 Volts ISI Marked,1 module, complete all as specified and directed.

S&F Modular socket outlet 2 in 1, 6 pin, 5 and 16 amp flush type, 230 Volts ISI Marked,1 module, complete all as specified and directed.

S&F of Lamp holder, metal cased, bakelite body, 230 volts, including 9 watt LED lamps (ISI Marked) etc, complete all as specified and directed.

S&F Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including AC decorative box type with driver, holder including,copper conductor cable of suitable size from ceiling rose complete complete, 4 ft long, complete all as specified and as directed.

S&F bldg security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and as directed.

S&F in LED COOL White light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by the Engineer-in-Charge.

S&F MCB, C Curve type, 10 kA, 40 Amp to 63 Amp, SPN with over load and short circuit protection, complete all as directed and directed by the Engineer-in-Charge.

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed and directed by the Engineer-in-Charge.

Supply and fixing as MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall all as specified and directed by the Engr-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed by engr-in-charge.

M&L for earthing complete with galvanised steel earth electrode 60cmx60cmx6mm buried directly in ground vertically to depth not less than 2.25m below normal ground level with top edge of the earth plate at a depth not less than 1.5m below ground level connected to and including GI earth lead wire 4 mm dia by means of nuts, bolts, check nuts and washer etc, made of GI and connected to test point and earth dolly all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC (1:3:6) Type C1 in chamber, precast RCC 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 mm dia with cast iron frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed. Note:- (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead.

Supply, laying testing, in trenches/on wall / in duct/ through protection pipe LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 16 sqmm 2 core etc. complete all as specified and directed. Note : Earth work and brick work measured and paid separately

Supply, laying testing, in trenches/on wall / in duct/ through protection pipe LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 16 sqmm 2 core etc. complete all as specified and directed. Note : Earth work and brick work measured and paid separately

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 2, flat, size 300x180mm x40 mm, complete all as specified and as directed.

Supply and lay sand for sand cushioning for cable protection in trenches all as directed and specified in SSR Part - 1.Note:. for the purpose of payment punned thickness will be measured etc, complete all as specified and directed. .

Supply and fix GI tubing medium grade of 40 mm dia for cable protection etc, complete all as specified and directed.

Note:- (i)- Qty's have been clubbed from 3 Nos sanction Job's, whose details as per appx NOTE:- (i)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

Ashwani Associates (BID ID -3470468)

M/S KAUTILYA GARG (BID ID -3480526)