Buildings

Drilling of Bore well by down the hole hammer drilling to a finished dia of 112/165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc., and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suoit insertion of casing pipe with couplings, caps any other relevant materials up to required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development ( Flushing of Bore well at an average pressure of 150 PSI) conducting yield test consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction ofthe department and including all labour charges but excluding all taxes, the cost of casingpipe, couplings, cap eytc., The entire work should be carried out as per IS-2800 Part I&II 1979 and amended from time to time. 165mm dia bore

Supply and Delivery of PVC Casing pipe of dia 250 mm/6Kg/Cm2 with one end socket as per ISI 1239/part-1/79 for casing purpose.

Supply and Delivery of PVC Casing pipe of dia 180 mm/6Kg/Cm2 with one end socket as per ISI 1239/part-1/79 for casing purpose.

Supply and Delivery of PVC Casing pipe of dia 125 mm/6Kg/Cm2 with one end socket as per ISI 1239/part-1/79 for casing purpose.

Supply and transportation of 1.00 HP-10stage star rated submercible motor pump set, conforming to IS 8034 and motor confirming to IS 9283 with water proof winding, pump shall be suitable for various delivery head and discharge with stainless steel shaft. Mpotor suitable for working on 415 V + 10% , Three Phase 50 HZ AC supply, etc, complete for 4" Bore well. Makes :: EKKI

Manufacture, Supply, & Delivery of HDPE Pipes conforming to IS 4984 - 2016 including transportation to anywhere in A.P, excluding all taxes (Supply up to 90 mm dia. in coil & above 90 mm dia. straight length.) (8.0 kg/sqcm)

Supply and Delivary of Specials in cluding all type of charges etc 40 mm dia SS Nipple

25 mm dia SS Nipple

20 mm dia SS Nipple

20 mm dia Non Return Valve

20 x 15 mm Dia Reducer

15 mm dia Nipple

Fabrication ,transportation and supply of wall mounted panel board of size 600x600x250 mm made of 18 SWG mounting plate for cable entry fabricated, painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T /Finolex copper FRLS Cables of suitable size and capacity and cable clamp etc complete for 3 Phase motor pump sets.

Supply and Delivary of MS Clamp set

Supply of 3 core 6.0 mm Flat Copper Cable of ISI for submersible Motors confirming to IS:694:1990. Makes : Finolex/RR Kabel/KEI / Polycab / Havells/Gloster / Gold Medal / GM

Engaging JCB for jungle clearance including cost and conveyance of all kind of labour charges etc.,

Augoring and boring of holes in site for Bored cast-in-situ R.C.C. Piles for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils without under reams as per IS 2911 as per approved designs including all operations, incidental, labour charges, hire charges of machinery, augur bore drill and shell equipment, etc, complete for all depths and for finished item of work for piles of following diametres. 450mm dia Double Under Reamed pile Bores

Under - reaming for BORED CAST-IN-SITU R.C.C PILES for building foundation in loamy, clayey soils like black cotton soils and ordinary soils without under reams as per is 2911-1980 as per approved designs including all operations, incidental, labour charges, hire charges of machinery ,augerbore drill and shell equipment, etc, complete for all depths and finished item of work for piles of following diameters.(450 mm dia - DOUBLE UNDER REAMING)

Providing High Yield Strength Deformed (HYSD)/ Thermo Mechanically Treated (TMT) / Mild steel (MS) steel bars (Fe 415/ Fe 500 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Supply and placing of the M25 Nominal Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, pouring concrete by tremmy, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including tremmy pumping, laying concrete, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work..

Providing High Yield Strength Deformed (HYSD)/ Thermo Mechanically Treated (TMT) / Mild steel (MS) steel bars (Fe 415/ Fe 500 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Supply and placing of the VRCC M-25 Grade Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. (BLD-CSTN-2-14) For Pile caps

For Coloumns GF Roof Beam

For Coloumns FF Roof slab

For Plinth beam

Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost of all materials and labour charges for curing and scaffolding charges etc., complete)

Collection, supply and filling of Stone crusher dust finer than 3mm with not more than 10% passing 0.075 sieve including cost and conveyance of all materials, labour charges, watering and compacting etc., complete as per ss under bed concrete

Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixture including cost and convayance of all materials, labour charges, machine mixing and curing charges etc., complete as per S.S.

Providing High Yield Strength Deformed (HYSD)/ Thermo Mechanically Treated (TMT) / Mild steel (MS) steel bars (Fe 415/ Fe 500 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Supply and placing of the VRCC M-25 Grade Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. (BLD-CSTN-2-14) Gorund Floor - For Staircase

Ground floor Roof Beam

Ground floor Roof Slab

Ground floor lintel beam

Ground floor Sunshade

First Floor - For Staircase

First floor Roof Beam

First floor Roof Slab

First floor lintel beam

First floor Sunshade

Providing Impervious coat to exposed RCC Roof Slab surface ith C.M.(1:3) 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost of all materials, seigniorage charges, excluding conveyance charges of materials and including charges all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junction of wall and slab etc, complete for finished item of work as per S.S. Ground Floor

Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost of all materials and labour charges for curing and scaffolding charges etc., complete) Ground Floor

Plastering with CM (1:4), 20 mm thick including cost & conveyance of all materials and labour charges curing etc., complete out Side Ground Floor

In Side First Floor

White washing three coats with whiting of approved quality to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials, labour charges and incidental such as scaffolding, lift charges etc., complete for finished item of work, but excluding conveyance charges of materials. as per plastering quantity Ground Floor

as per plastering quantity First Floor

Painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, inlcuding cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for Internal walls.

Painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, inlcuding cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for External walls. as per plastering quantity -Ground Floor -External Walls

as per plastering quantity -First floor - External Walls

Flooring with Non-skid ceramic tiles of size 600 x 600 mm thick between 8-10 mm, set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete for finished item of work as per directions of the departmental authorities. Ground Floor

Providing skirting to internal walls to 15 cm height/risers of steps with vitrified tiles length equal to flooring stones, set over base coat of CM (1:5) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete for finished item of work. Ground Floor Skirting

Supply and fixing of Doors as per Drawing with medium Teak wood frame of secion 100mm x 65mm and ISI marked flush door shutter of 30 mm thick single shutter with bond wood solid block board type Core having cross bands and face veeners, hot pressed bonded with water proof phenol formal dehyde synthetic resin factory made conforming to IS 2202 - 1991 ( Part-1) both sides commercial ply with internal lipping on all sides including cost and conveyance to site of medium teak wood door frame, flush shutter, including supply and fixing 6Nos. MS Z hold fasts of size 300 mm x 40 mm x 5 mm including ISI marked Aluminium fixtures 3 Nos Butt hinges (IS:205) of 150 mm long, 1 NO.Aldrop (IS:2681) 300 mm long 1 No Tower bolt ( IS 204) of 200mm x 10 mm dia, 2 Nos. 150 mm long handles (IS208), 1 No. Door Stopper , Rubber/Nylon door stop bushes including fixing the fixtures to door with required number of screws, bolts and nuts including labour chrges for fixing the frame in position, fixing the shutter to the frame etc., including including overheads & contractors profit complete for finished item of work as per APSS 1001 & 1002. ( THe Vertical frame of door shall be embedded in flooring for depth of not less than 10 mm ( 1550mmX 2500mm).

Providing and fixing factory made UPVC White colour sliding glazes window comprising of UPVC multi chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.6 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length ( Shape & size acording to UPVC profile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy ( white powder coated ) touch locks with hook, zinc alloy with single nylon rollers weight bearing capacity to be 40 kg), G I fasteners 100x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc., . Profile of frame & sash shall be mitred cut and fusion welded at all cornerssss including drilling of holes for fixing hardware and drainage of water etc., after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-charge inclusive of cost of single/double glass panes, wire mesh and silicon sealant. Note: For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this acount shall be made. Three track three panels sliding window with fly proof SS wire mesh ( Two nos. glazed & one no. wire mesh panels) made of frame 92 x 44 mm & sast 32 x 60 mm both having wall thickness of 1.9 +/- 0.2 mm and single glazing bead of appropriate dimension.(1500mmX1500mm)

Supply and Fixing of 25mm dia 1.80mm thick PVC pipe (ISI MARK) concealed in Slab with all required accessories including masonary work and labour charges etc., complete..

Supply and fixing of Anchor fastener with fan hook / Providing MS Fan hook with grouting and cement plastering.

Supply and fixing of 25 mm outer dia medium grade (1.8 mm thick ) confirms to IS:9537 part 3 FRLS rigid PVC pipe (ISI marked) concealed in wall with all required MS junction boxes and all accessories including masonry work forlight, bell, fan and seperate plug point with hot dip galvanized 20/18 SWG MS modular metal switch box with earthing terminal includingalllabourchargesetc.,completeMakes::Precision/Universal&Marudhar/VIP/Goldmedal/Millionplast/GM/Sudhakar/Anchor/Polycab.

Wiring with 2 runs of 22/0.3 mm (1.5 Sq mm ) FRLS/ FRLSH /HFFR /ZHFR P.V.C insulated 1100 V grade as per IS: 694 / 1990 specification flexible copper cable (ISI marked) in existing pipe with 6A Modular switch (ISI marked) with cover plate, ceiling rose/BH/SBH, including all labour charges etc., complete Light, BEll, Fan and exhaust Fan points etc., complete .Makes Wires :: Finolex/RR Kabel/Havells/KEI/Polycab/Gloster/V-Guard/HPL/GM/Million/Goldmedal/Anchor.Makes of Switches :: Legrand Myrius /Crabtree verona /L&T/HPL/Schneider Livia/ GM/(Zicono/Four Five) /C&S/Gold Medal ( Curve) Million Mway/Logus Platina/Panasonic Vision/Salzer S90 Series /Anchor-Roma.

Supply and fixing of 16A/6A, 2 in one Modular type socket with 16A Switch ( ISI Marked) Modular type with Cover plate on existing modular metal switch box including all labour chrges, giving all connections etc., complete. Makes of Switches :: Legrand Myrius /Crabtree verona /L&T/HPL/Schneider Livia/ GM/(Zicono/Four Five) /C&S/Gold Medal ( Curve) Million Mway/Logus Platina/Panasonic Vision/Salzer S90 Series /Anchor-Roma.

Supply and fixing of 16A/6A, 2 in one, modular type power socket outlet with 16A switch (ISI Marked) modular type and 1 No of 6A modular type and 1 No of 6A modular type sockets with 6A modular type (ISI marked) switch control with front cover plate on existing modular metal switch box including all labour charges, giving all connections etc., complete with following configurations. 1) 16A Socket - 1 No. 2)16A Switch - 1 No. 3) 6A Socket - 1 No. 4) 6A Swithc - 1 No. Makes of Switches :: Legrand Myrius /Crabtree verona /L&T/HPL/Schneider Livia/ GM/(Zicono/Four Five) /C&S/Gold Medal (Curve) Million Mway/Logus Platina/Panasonic Vision/Salzer S90 Series /Anchor-Roma.

Supply and fixing of Single Phase DB in sheet steel enclosure as per IS 8623, IS 13032,IEC 61439-3 with metallic plug nd socket with 1 No. 20/32A,10KA "c" curve SPMCB control including labour charges and giving connections etc., complete on wall. Makes for DBs:: Legrand (Ekinox 3) /Schneider - Acti /Hager- Novello+/Seimens/L&T-Newrange and Makes for MCBs: Legrand-DX3 /Schneider-Acti/Hager-h3/Siemens-5SX4/Crabtree-Xpro/L&T-AU.

Wiring with 2 runs of 22/0.3mm (1.5 Sq.mm) FRLS/FRLSH/HFFR/ZHFR P.V.C. insulated 1100V grade as per IS: 694/1990 specification flexible copper cable (ISI marked) in existing pipe with 6A Modular switch (ISI marked) with cover plate, Ceiling rose/BH/ SBH, including all labour charges etc., complete for Light, Bell, Fan and Exhaust Fan points etc., complete. (for Non Residential Building) Makes of wires :: Finolex/RR kbel/ Havells/KEI/Polycab/Gloster/V-Guard/HPL/GM/Million/Goldmedal/Anchor.

Supply ad run of 2.5 sq.mm (phase neutral and earth) FRLS /FRLSH/ HFFR / ZHFR /P.V.C. Insulatedd 1100 v grade as per IS ; 694/1990 speification flexible copper cable in existing MS conduit pipe for individual lighting circuits including labour charges etc., complete as required for switch boards. Makes of wires :: Finolex/RR kabel / Harvells/KEI/Polycab/Gloster/V-Guard/HPL/GM/ Million/Goldmedal/Anchor.

Supply and 3 runs of 4.0 sq.mm (phase neutral and earth) FRLS/FRLSH/HFFR/ZHFR/P.V.C. Insulated 1100 V grade as per IS:694/1990 specification flexible copper cable in existing conduit pipe for run of mains including labour charges etc., complete as required including labour charges for 16A sockets. Makes of wires :: Finolex/RR kabel / Harvells/KEI/Polycab/Gloster/V-Guard/HPL/GM/ Million/Goldmedal/Anchor.

Supply and runs of 5 of 6.0 sq.mm (phase neutral and earth) FRLS/FRLSH/HFFR/ZHFR/P.V.C. Insulated 1100 V grade as per IS:694/1990 specification flexible copper cable in existing M.S conduit pipe for circuits including labour charges etc., complete as required for run of mains from Lighting panel board to TPN DB's with pin type lugs and connections. [ for (LDBs)]including labour charges for 16A sockets. Makes of wires :: Finolex/RR kabel / Harvells/KEI/Polycab/Gloster/V-Guard/HPL/GM/ Million/Goldmedal/Anchor.

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of >=100 lumens/watt , PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warrantyMakes : a) LUMINAIRE : Philips/GE-Venture /Crompton/Wipro/Bajaj?Havells b) LED Make : Philips Lumileds / Cree/Nichia/Osram/Samsung.

Supply of 48" (1200mm) Sweep 5 star rated BLDC (Brush less Direct Current) Ceiling Fan with double ball bearings, input voltage 230V AC converted to 24 V DC, power input not more than 32W , air delivery 210/220 cubic meter/min with remote and without Regulator. Makes : Atomberg(Gorilla GV2 )/ Halonix(Plasma) /Havells(Efficiencia)

Supply and erecting 19/20mm steel tube down rod of 0.75 mts length with bolts & nuts duly painted with matching colour of fan complete.

Supply, Transportation and fixing of 60W LED Street light Luminaire made of pressure diecast aluminium body with powder coated haing protective toughned glass, supply input voltage 120-270V AC, P.F>0.90, high power LED's having system efficacy>100lm/W and junction temperature<70C, with ingress protection 4KV, external Surge protection 10KV with Optics distribution. THD<10% at 110 Volts AC, driver efficiency>90%,CCT:3000K-5700K, minimum CRI>70 etc., complete including fixing of luminaire on wall/Pole with 1.0 mts of 40 mm dia G.I pipe bracket and nti/tilting MS flat, 3 core 1.5 Sq.mm shethed flexible round copper cable including all labour charges and giving connections et., complete. a) Luminaire make : Wipro(Skyline)/Philips (green line) / GE-Venture / Crompton (Nexus star )/ Bajaj (Edge) /Havells (Endura Pearl). b) LED make : Philips Lumileds /cree/Nichia/Osram/Samsung/LG LEDs

Fixing of LED street light on wall with 1.0sqmm 40 mm dia GI pipe bracket and MS flat with 2.5 Sqm flexible copper wire etc., including labour charges for Mason work and giving connections etc., complete.

Supply and Fixing of Batten Holder/aangle holder on existing block wth 5W LED Lamp with input voltage 90 to 300v, colour temperature 3000k -6500k, Beam angle 170 -220 degrees , B22 base and all labour harges etc., complete. In lieu of ceiling Rose.Makes: Philips/Crompton/Bajaj/Havells/GM/HPL/Syska/Gold Medal.

Labour charges for fixing of ceiling fan including transportation and giving connections with 3 core wire leads etc., complete.

Supply and Run of 25 mm x 6 mm G.I Strip including cost of all accessories and labour charges etc., complete.

Providing independent earthing for important equipment with 40 mm dia 'B'Class 2.5 m long G.I pipe and 19 mm dia 'B'Class G.I pipe of 0.3 mtr. Long connected with reducer providing G.I funnel with mesh enclosed in C.Cchamber of 400mx400mx400mm with RCC slab cover duly providing staggered holes filling with salt and harcoal from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6 mm x 200mm length with all accessories and labour charges complete. as per IS Specifications 732/1982 (Part II)

Supply and fixing of Ashirvad/ Ajay/ Astral Flowguard or equivalent CPVC Pipes and Fittings SDR 11 to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" to 2") for hot and cold water (IS 15778:2007) including cost and conveyance of all materials to site, labour charges for fixing, overheads & contractors profit complete for finished item of work at all floor levels. a) 1" dia ( 28.60 mm OD pipe ) - SDR 13.5 North side Toilets In side

a) b) 1 1/2" dia ( 41.30 mm OD pipe - SDR 13.5) Tank to

Supplying and fixing of SWR PVC pipes (Prince/Sudhakar/Kisan/Supreme or any ISI brand) 4 Kg/Sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges, overheads & contractors profit complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326) 75 mm dia

Supplying and fixing of SWR PVC pipes (Prince/Sudhakar/Kisan/Supreme or any ISI brand) 6 Kg/Sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges, overheads & contractors profit complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326) 75 mm dia

Supplying and fixing of 4" (101.6mm) multi floor trap with jali - UPVC/SWR pipe fittings as per site requirements with standard practice for all floors including cost and conveyance of all materials to site, labour charges , overheads & contractors profit etc., complete for finished item of work.

Supply and fixing Indian make Flat Back Wash Hand Basin ( HSW/Parryware/Neycer) ist quality conforming to IS: 2556-part-4:1972 with waste fittings like rubber plug, chain, 32 mm nominal size C.P Fittings with parallel pipe tread conforming to IS:2963-1979 and fitted with 15 mm nominal bore chromium plated pillar Tap of ist quality Indian make 400 grams Seiko/Senior/Nice?Esso or equivalant complete with standard CI brackets including wooden block: 550 x 400 mm - Single C.P Pillar cock.

Supplying and fixing NP bib taps of Indian make heavy duty (long body) as approved by the Engineer-In-Charge including cost and conveyance of all materials, labour charges , overheads & contractors profit complete for finished item of work in all floors.

Providing and placing on Terrace (at all floor levels) polyethylene water storage tank with Double layer approved brand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlet and over flow pipes but with out fittings & base support for tanks

Supplying and fixing Gunmetal Gate ( GM peet ) valve as per IS-778 Class - I , Indian make heavy type including cost and conveyance of all materials , labour charges , overheads & contractors profit complete for finished item of work. 11/2" Dia Gate valve

1' Dia Gate Valve

Supply and fixing of MS Grill to windows using 25 x 6 mm MS Flat alround nd 10 mm MS square Horizontally @ 125 mm cenre to centre and vertically 300 mm c/c including fixing with 4 Nos Z hold fasts 2 on each side duly making.

Providing synthetic enamel paint two coats over primary coat total three coats to MS Grill including cost and conveyance of all labour and materials at site of work complete.

Melamine Polish Glossy/Matt finish to the wood work duly cleaning the surface and pplying emery paper, sand the wood with 180 No. Emery paper and then with 320 No. Emery paper, clean & wipe off loose dust, appying suitable knifing paste filler/wood filler by putty knife/muslin pad , air dry for 2-3 hours, sand with 180 nd 320 No. emerypaper, apply two componenet wood sealer, air dry for 24 hours, sand with 320 No. emery paper, applying one coat of approved spraying thinner ( for spraying)/applying one coat of approed brushing thinner or general purpose thinner ( for brushing) and apply 9either with spray or brush) two coats of approved brand melamine including cost & labour charges, emery papers, cost of thinner & melamine polish, over heads and contractors profit etc., complete for finished item of work.

Providing High Yield Strength Deformed (HYSD)/ Thermo Mechanically Treated (TMT) / Mild steel (MS) steel bars (Fe 415/ Fe 500 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Supply and placing of the VRCC M-25 Grade Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. (BLD-CSTN-2-14) Raising Coloumns

Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost of all materials and labour charges for curing and scaffolding charges etc., complete)

Providing Plasteing with CM (1:3), 12 mm thick including Cost & Conveyance of all materials and labour charges for mixing and curing etc., Complete as per S.S.

Painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, inlcuding cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for External walls.

Manufacture, supply, delivery and fixing of Window grills, Compound wall grills, Iron Doors, Windows made with MS flats etc including welding, finishing, applying red oxide paint as primary coat etc complete unit 1.00 kgs

Painting to new iron work with synthetic enamel paint two coats over pirmary coat with red oxide paint including cost and conveyance of all materials and labour charges etc., complete

Augoring and boring of holes in site for Bored cast-in-situ R.C.C. Piles for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils without under reams as per IS 2911 as per approved designs including all operations, incidental, labour charges, hire charges of machinery, augur bore drill and shell equipment, etc, complete for all depths and for finished item of work for piles of following diametres.

Providing High Yield Strength Deformed (HYSD)/ Thermo Mechanically Treated (TMT) / Mild steel (MS) steel bars (Fe 415/ Fe 500 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Supply and placing of the M25 Nominal Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, pouring concrete by tremmy, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including tremmy pumping, laying concrete, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work..

Supply and placing of the VRCC M-25 Grade Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. (BLD-CSTN-2-14) Above G.L Coloumns

Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost of all materials and labour charges for curing and scaffolding charges etc., complete)

Providing Plasteing with CM (1:3), 12 mm thick including Cost & Conveyance of all materials and labour charges for mixing and curing etc., Complete as per S.S.

Painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, inlcuding cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for External walls.

Flooring with vitrified tiles of 1st quality, set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, etc., complete for finished item of work, but excluding the cost of conveyance of all materials..

Dadooing to walls with Glazed red or white full body ceramic wall tiles of size 200 x 300mm and thickness 6mm 1st quality set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete for finished item of work.

Providing and fixing 30mm thick Solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5mm thick heat moulded PVC ‘C’ channel of size 30 x 50mm forming stiles, and 5mm thick, 75mm wide PVC sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with 30mm wide x 5mm thick PVC sheet beading on either side, and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive. Complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing for finished item of work.

Collection, supply and filling of Stone crusher dust finer than 3mm with not more than 10% passing 0.075 sieve including cost and conveyance of all materials, labour charges, watering and compacting etc., complete as per ss under bed concrete

Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixture including cost and convayance of all materials, labour charges, machine mixing and curing charges etc., complete as per S.S.