Providing Aluminium Partition wall with door at Newly Constructed Academic Block - II in SVU Campus, Tirupati

Providing, fabricated, assembling and fixing in position powder coated anodized aluminium partitions powder coated minimum of 60-70 microns Jindal/ Hindalco or equivalent make using sections in combination of plain, single grove and double grove as per requirements for the frames of over all size 101.6 mm x 44.45mm, 3.18 thick having section weight, plain sections 2.40 kg/m single grove section 2.541kg/m and double grove section 2.683 kg/m and bottom member 114.3mm x 44.45mm x 3.18mm thick and 2.6 46 kg/m, aluminium louvers of size 77.6mm x 27.6mm x 1.70mm thick section weight 0.483kg/m, bottom portions provided with 12 mm, thick prelaminated sheet both side of approved colour lamination exterior grade aluminium sections of matt finish or glossy finish using section, spacing of vertical member shall not exceed 0.6 m. c to c, sections are cut to the required lengths, joints metered and corners grinded subdividing frames tennoned and rivetted to the frames,the assembled frame should be stiffened with corner angles stripped and fixed with screws, rawl plugs and teak wood gutties to R.C.C.columns or masonry on sides, R.C.C.intels or beams at top and floor at bottomlintels or beams at top and floor at bottom, including cutting chiselling and making good with cement mortar to match the surface, providing and fixing bottom panel filled with the materials to a height of 0.9m from floor level and 5mm thick plain/ Pin headed glass for middle / Top portion viz., 0.9m to 2.13m and top panel with lower sections, the glass and panels fitted with glazing clips of 19mm x 17.3mm. With thickness of 0.9mm, weight 0.124 kg/m aluminium sections pre-treated for removal of any rust and prevention of further rust formation, and coated with greasy materials for non-adherence of mortars of any other sticky materials, vertical members embedded in the flooring by making suitable size holes and fixing with cement mortar, with necessary opening for fixing of doors of standard size (excluding cost of door opening). All the frame should be thoroughly cleaned free from rust, scale or dirt including cost of materials, fixtures, labour and HOM of machinery complete as per specifications.

Providing, fabricating assembling and fixing in position, anodized Aluminium doors powder coated minimum 60-70 microns Jindal/ Hindalco or equivalent make using following aluminium mat finish or glossy finish,Outer frame Plain section 101.60 x 44.45mm thickness .18mm, section weight 2.404 kg/m, door shutters vertical section 44.62 x 44.45mm thickness 3.18mm, section weight 1.505kg/m, top section 47.62 x 44. 45mm thickness 3.00mm, section weight 1.426kg/m bottom section 114.30 x 44.45mm thickness 3.18mm, section weight 2.646kg/m, door central section 49.91x44.45mm thickness 3.00mm, section weight 1.495kg/m glazing clips 19x17.3x11mm thickness 0.9mm section weight 0.124kg/m; aluminium sections cut to length joint metered corners grinded, the shutters pivoted opening arrangement with heavy duty aluminium alloy automatic door closures floormounted, providing and fixing standard approved accessories, such as aluminium handle for full width or length, tower bolts, lock, pivots: P.V.C. or rubber gasket with 5mm thick plain / pin headed glass for top and bottom panel; aluminium sections treated for removal of any rust and prevention of further rust formation, and coated with greasy materials for nonadherence of mortars or any other sticky materials; the assembled frame fitted with the corner angles, strips and fitted with screws, rawl plugs or teak wood gutties to R.C.C. columns or masonry on sides, beams and flooring in bottom including cutting, chiselling and making good with cement mortar to match the surface;all the frames thoroughly cleaned free from rust, scale or dirt including cost of materials, fixtures, labour and HOM of machinery, complete as per specification.