CONSTRUCTION OF BRTS BUS SHELTER ON UDHANA TEEN RASTA TO DINDOLI-KHARVASA (MADHURAM CIRCLE) IN SURAT CITY.(3RD ATTEMPT) (WORK-3)

e-Tender Notice No.:ACE(Ele./Mech.)/Traffic BRTS Pro. Cell/04/2026-27, Work No.3

NAME OF WORK :- CONSTRUCTION OF BRTS BUS SHELTER ON UDHANA TEEN RASTA TO DINDOLI-KHARVASA

(MADHURAM CIRCLE) IN SURAT CITY. (3rd Attempt)

Item Quantity Rate Unit

1 Providing and installing barricades including supplying, paiting

with flourscent paint/white paint and fixing CGI sheet 24 SWG of

required height as per site condition and M.S. angle of required

size to restain at 2.5 mt. c/c and dismantalling the same after

completion of work and allowing for movement of traffic as per 540.00 124.72 S.M.

drawing and as per instruction from engineer in charge

2 Reuse of the above barricades in item 1 for traffic safety purpose

without procuring new barricades. 540.00 28.32 S.M.

3 Provision of Solar Blinkers For barricading for limited period at

suitable locations as per requirement during the construction in

construction zone comprising of warning zone, approach

transition zone, working zone and terminal transition zone Etc. 10.00 248.00 Nos.

4 Demolition including stacking of serviceable materials with all

lead and lift. (i) RCC Work 10.00 1110.75 C.M.

5 Demolition and disposal of unserviceable materials with all lead

and lift (ii) Unreinforced cement concrete

6 Demolition and disposal of unserviceable materials with all lead

and lift (i) Paver Block

7 Excavation for foundation includ.sorting out & stacking of useful

materials & disposing of the excavated stuff upto 50 mt. Lead &

all lift, watering etc. Comp. (A) Loose or Soft soil Executed With

8 Boring holes 3.5 mt.deep in ordinary soil ( for cast in situ piles) &

disposal of the surplus excavated soil as directed within a lead of

50 M. For following diameter of piles.

9 Providing & laying C.C 1:3:6 (1cement : 3 coarse sand : 6 Crushed

stone agg 20m.m Nominal size) &curing comp. excl. cost of form 56.00 3095.25 C.M.

work in :(a) foundation & Plinth

10 Providing & laying cement concrete 1:1.5:3 (1 cement:1.5 sand:3

graded stone agg. 20 mm nominal size)& curing comp.

Includ.cost of form work but exclu. Cost of reinforcement for

reinforced concrete work in : (A) Foundation, footing, Base of

columns and Mass concrete.

Item Quantity Rate Unit

11 Providing & laying ordinary cement con. 1:1.5:3

(1cement:1.5sand: 3 graded stone agg. 20 mm nominal size)

finishing smooth curing etc. comp. Incld. Cost of form work but

excl. Cost of reinforcement for R.C.C. Work in : Up to G.L./P.L. (B)

(1)Having c/s area up to 0.08s.mt 0.00 9102.61 C.M. -

(2) Having c/s area more than 0.08 sq. mt. & upto 0.12 sq.mt

(3) Having cross sectional area more than 0.12 sq. mt. 0.00 7086.88 C.M. -

12 Providing & fixing IS Mark TMT Bar FE 500D reinforcement for

R.C.C. work incl. bending, binding & placing in position etc. comp. 16550.00 77.29 Kg.

13 Filling available excavated earth (excluding rock) in trenches.

plinth, sides of foundations etc. in layers not exceeding 20 cm. in

depth consolidating each disposited layer by ramming and

14 Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar

1:4 (1- Cement : 4 -coarse sand ) in foundation and plinth (C)Fly

15 Providing 20 mm thick double coat mala cement plaster on brick

/ concrete work for plastering comprising of base coat 12 mm

thick cement plaster in cement mortar (1 Cement : 4 coarse sand)

in rough finishing and 8 mm thick top coat of cement mortar 1:2 592.00 286.10 S.M.

(1 Cement : 2 Coarse sand) finished with trovel including

scaffolding curing etc. complete.

16 Providing and laying polished Kota stone slab flooring over 20mm

(Average) thick base of cement mortar 1:6 (1-cement : 6-coarse

sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and

jointed with grey cement slurry mixed with pigment to match the

shade of slab including rubbing and polishing etc. complete. (A)

17 Providing and laying chequered precast concrete tiles 22mm

thick with aggregate of sizes upto 6mm in floors treads of steps

and landing on 20mm thick bed of C.M. 1:6 (1 cement : 6 sand) or

L.M. 1:1.5 (1 Lime putty : 1.5 sand) jointed with neat cement

slurry with pigments to match the shade of the tiles.

18 Providing and fixing 40 mm thick polished granite stone slab of

approved colour and make for platform in ticket cabin area,

machine cut to required size with edges machine polished and

chamfered as directed. The granite slab shall be laid over cement

mortar bed (1:4) of average 20 mm thickness over prepared base,

properly aligned, levelled and jointed with matching shade

epoxy/cement slurry. The joints shall be neatly finished and the 20.00 6190.80 S.M.

top surface shall be properly cleaned and made ready for use.

The item shall include cutting, handling, laying, curing, polishing,

labour, materials and all incidental charges complete in all

respects as per directions of the Engineer-in-charge.

19 Steel work welded in built up sections, framed work including

cutting, hoisting, fixing in position and applying a priming coat of

red lead paint (A) in beams & joists channels angles, tees, flats

with connection plates or angle cleats as in main & cross

beams,hip & trussed purlins connected to common raffers & the

Item Quantity Rate Unit

20 Providing and Fixing Hollow steel Sections Framed Work including

Cutting, Hoisting, Welding & Fixing in position Purlin, Main Chord

etc. as per Engineer- in-charge.TATA / JINDAL / ASIAN Make.

21 Fabricating, supplying, cutting, bending, fixing and assembling

frames etc using aluminium sections of JINDAL/HINDALCO make

or equivalent of thickness and fixed to MS framing, concrete

members etc with S.S.screws in counter sunk/ S.S. rivets, S.S

washers, SS anchor bolts, cleats, hangers etc and other necessary

accessories and hardware complete as per detailed drawing and

design. (Only finished measurements will be paid for, M.S.

framing shall not be part of this item.) The rate shall include

micron annodising of approved shade. The sheet type will be 918.00 535.00 Kg.

finalised by the consultant. The rates shall be inclusive of rubber

gaskets and all other hardware. Cutting and making of framing

etc shall be done by experts. The rates shall be inclusive of all

mechanized tools, cutters, bending machine work, grinders etc.

22 Providing and fixing stainless steel ( Grade 304) railing made of

Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories &

stainless steel dash fasteners , stainless steel bolts etc., of

required size, on the top of the floor or the side of waist slab with

suitable arrangement as per approval of Engineer-incharge, (for 450.00

payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts,

fasteners etc.).

23 Providing & fixing Aluminium Composite panel of alum decor,

Indobond & Flexibond make to all Sufaces 4mm thick in required

colours of exterior consisting of two layers of aluminium skins of

0.25mm thick sandwiching a thermo plastic core in continuous

lamination process with PVDF coating of exterior grades ensuring

long life colour and fungal resistance. Base frame work with

aluminium sections shall be fixed over the all surfaces, ACP shall 944.00 1310.98 S.M.

be fixed to the frame work as cladding it includes cost of labour

,Materials, accessories, adhesive, scaffolding, wastages,

transport, taxes, fixing into a neat finish in aesthetic point of

view, without any undulations in facias all complete as per

drawing and instruction of engineeer in-charge.

Item Quantity Rate Unit

24 Providing and fixing in position as per designs 10mm thick

toughened glass of required size with diamond polished edges of

Asahi, Modiguard make or equivalent. The glass shall be firmly

fixed to the base surface using structural silicon of Dow Corning

or Wacker make. The contractor shall ensure that the base

surface is thoroughly cleaned prior to fixing of glass and the 35.00 4082.44 S.M.

assembly shall be made completely water tight. The contractor

shall check for water tightness and provide a certificate for the

same. The work shall be executed to the complete satisfaction of

the Engineer in charge and the work area shall be made totally

clean on completion of the work.

25 Providing and fixing factory manufactured PUF (Polyurethane

Foam) insulated sandwich roof panels of 50 mm thickness having

pre-painted colour coated GI sheet of minimum 0.45 mm

thickness on both sides with injected rigid polyurethane foam

core of density not less than 40 ± 2 kg/m³, suitable for roofing

application. The panels shall be laid over MS purlins with proper

alignment and slope, fixed using self-drilling screws with EPDM

washers to ensure complete water tightness. The joints shall be

interlocked and sealed with approved sealant to prevent leakage.

The work shall include cutting to required size, lifting, placing,

fixing, finishing edges, ridge/side flashing where required and

making the entire roof assembly fully weatherproof. The

contractor shall ensure proper slope for drainage and provide

water tightness certificate after completion. The work shall be

executed to the complete satisfaction of the Engineer-in-charge.

26 Providing and fixing terracotta blocks of size 8" × 8" × 2.5" in

approved pattern using polymer modified adhesive / chemical

mortar system, properly aligned and levelled to form ventilated

screen wall of required height. The item shall include cutting, 3525.15 S.M.

alignment, temporary bracing, adhesive application, curing,

scaffolding and all labour, materials and incidental works

complete as per approved drawings and directions of the

Engineer-in-charge.

27 Providing and installing in position HDPE synthetic Fiber carry

rollers of 100mm dia as per the design drawings of the

Consultant. The rollers shall have seals which are with labyrinth

seal components, non-rubbing polymer seal and attached with

dust and water deflectors. The rollers shall be such that they shall

have good rolling during impact and shall not damage the body of

the bus nor shall get damaged during impact and shall act as a

protecting mechanism for the bus and the surface of the bus

shelter. The installation of the rollers shall be as per the 140.00 929.00 Nos.

instructions of the manufacturers. Samples shall be approved

prior to installation. Roller shafts shall be made of stainless steel

and multi labyrinth seals shall be filled with high grade lubricants.

Item Quantity Rate Unit

28 Providing & applying two coats of weather shield max paint (3

coats may be required in case of darker colours.)of ICI Dulux or

Apex Ultima of Asian Paint including applying exterior acrylic

primer coat as per manufacturers specification and directions in

shade and colour approved by architects, on exterior surfaces of

the building including scaffolding, preparing the surface,

watering, curing etc. complete and as directed by the architects

and manufacturers.

Surface Preparation :

surface is thoroughly clean, dry and free from all loose dirt, chalk,

grease, fungi, algae and flaking paint. This can be achieved by brushing

with a wire/ stiff coir brush, followed by water jetting if required. Fill

up all minor cracks and defects with white cement and sand mixture in

the ratio 1:3. For application on previously painted wall, previous

coatings of paint must be thoroughly scraped off and Clean the surface

thoroughly using wire brushes.

Apply a liberal coat of exterior acrylic primer and allow it to dry for 4-5

hours. Application of putty is not recommended.

Minimum 4-6 hours duration is required between each coat of weather

shield max paint

29 Applying Priming coat over new steel and other metal surface

after over and including preparing the surface by throughly

cleaning oil, grease dirt and other foreign matter and scoured 732.00 36.74 S.M.

with brushed fine steel wool, scrapers and sand paper with ready

mixed priming paint brushing red lead.

30 Painting two coat (excluding priming coat) on new steel and

other metal surface with synthetic enemal paint, burshing to give

an even shade including cleaning the surface of all dirt, dust and

other foreign matters.

Total Civil Work

ELECTRIFICATION WORK

Internal Wiring & Light Fixture

31 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on

PVC / Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (f) with medium

class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

Item Quantity Rate Unit

32 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length, in below

type of pipe erected complete with Modular type switch & 5 pin

Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per

pipe erected with following type of accessories.[I] For 6A Plug

and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby 20.00 510.05 Pt.

switchboard/mcb db board.(f) with medium class Rigid PVC

pipe and accessories erected concealed in wall/ceiling

complete Cat. III

33 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length, in below

type of pipe erected complete with Modular type switch & 5 pin

Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per 10.00 745.38 Pt.

pipe erected with following type of accessories.[II] For 16A Plug

and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db

board.(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

34 Wiring for the UPS / Comp. / Raw Power outlet with 2 nos. of

250 volts single phase and neutral 16 amps switched socket

outlet with 4 sq mm x 3 core FRLS Round flexible copper

conductor 1100 volts grade wires of approved make in

concealed or surface mounted Prelaid 25 mm dia medium guage

PVC Conduit / Race ways including providing and fixing of 2 no.s

of 16 amps 5 pin switch socket outlet of approved quality colour 20.00 1333.20 Nos

make & design in 2 mm thick GI box and earthing of fixtures

and the outlet box . ( Maximum 2 nos. of Plugs can be looped in

35 Providing following type of Modular Type Accessories mounted

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge. (4) TV Co-axial Socket outlet Cat. III

36 Providing & erecting Switch board for Computer or electric

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with single

mounting base frame covered with textured/metallic /white front

plate,modules erected with necessary connections as directed.

1 no. 6A/16A universal plug-switch combined. 10.00 1133.22 Each

3 nos. 6A Switch

3 nos. 6A 5 pin Plug Cat.III

37 Supplying & erecting approved make LAN cable of following size

in existing pipe as per direction [C] CAT -

38 Providing and fixing 350 x 350 x 40 mm deep 2 mm thick GI

sheet junction box including providing 3 mm thick stainless steel 30.00 914.05 Nos

cover as per specification.

Item Quantity Rate Unit

39 Supplying and erecting LED street light / Flood light fittings with

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown 20.00 3345.12 Each

ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.) (A)

Street Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection.

(i) above 36 to 48 watts Cat-lll

40 Supplying and erecting Street light pole bracket comprising main

B Class GI pipe of 4.2 cm/require outside dia. complete with

suitable B Class G.I. sleeve tubing of approx. 45cms.length and

suitable for 76.5mm/80mm/require size of pole top having nuts

and bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable welded

stiffener reducer and nipple with check nut complete painted with 20.00 491.87 Each

one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms. [A] Single

Arm bracket 0.5 Mtr

41 Supplying and erecting approved make Bracket fan of 230 volt,

A.C. 50 Cy/s., 400/450 mm sweep complete erected on wall or

with lead Cores and connections complete. Cat.II

42 Supplying and erecting LED indoor fittings with LEDs of wattage

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %, CCT

3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED

driver efficiency > 85 % ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may 80.00 758.51 Ea.

select any wattage capacity between the ranges shown.) (A)

Square/ Circular shaped Surface/Recessed Mount Downlight

with provision for spring loaded mounting clips

complete.IP65 (iv) 22-24 watts, Surge-2 KV Cat-III

Item Quantity Rate Unit

43 Supplying and erecting LED indoor fittings with LEDs of wattage

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/ aluminium die cast powder coated and high

U.V. & corrosion resistance with diffuser with company

mark/name 120 to 300 V,Power Factor more than 0.9, THD <

%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt

,LED efficiency110 lumens/watt LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA / 80.00 112.11 Each

SEOUL/Bridgelux make LED used for luminaire. ( fitting required

LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges

shown.) (A) LED Lamps integral type,cool white with PC

diffuser suitable for B22 LAMP holder (b) 5 to 8 watts cat-III

LT Switchgear, Distribution Boards & LT Panel

44 Providing and erecting Miniature circuit breaker single pole 6A to

25A suitable to operate on 240 V A.C. system and having

breaking capacity 10 KA to be erected in existing box. confirming 30.00 112.11 Each

to IS 8828/1996 with ISI Mark Cat.III (for lighs + fans + Tv)

45 providing and erecting Approved make RCCBs conforming

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance

feature & do not incorporate any electronic component. for 10.00 1969.50 Each

following Max. rating erected as directed (i) 25 Amps.DP

46 Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following capacity (A)

6 to 32 Amp. Cat.III (for AFSC)

47 Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 &

IEC 61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to be

used) suitable for

(A) single phase incoming and horizontal single phase outgoing

(a) single door (IP-30)

48 Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following capacity

49 25 A / 100 mA DP ELMCB 20.00 2323.00 Each

Cables and Wires

Item Quantity Rate Unit

50 Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following size.(A) with 300.00 82.82 Mtr

medium class Rigid PVC pipe and accessories.(b) 2 wire

51 Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following size 600.00 46.46 Mtr

(E) in existing pipe

(a) 2 wire 1.5 sq. mm

52 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road 300.00 676.70 Mtr

crossing or floor of following size of cables. (A) 4 core 10 Sq.

53 Providing and, fixing heavy duty flange type brass cable gland

with rubber ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of cables. (C)

2 to 4 core 10 Sq. mm

54 Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with 40.00 13.13 Each

brass/cadmium plated nut bolts in an approved manner. (B)

55 Making trench in soft soil of suitable width of 90 cm deep for

laying cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

56 Providing & laying approved make Double walled corrugated

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth in existing trench for laying of cable. below ground / road

surface for enclosing cable (A)50 mm outer dia

Earthing and Automatic sliding Doors & MISC

57 Providing and erecting HOT deep Galvanized iron strip wire 8 to

Item Quantity Rate Unit

58 Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound

with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover. (A)(approved

make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing resistane

mentioned in test Certificate) & having back filling compound of

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm /

meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at

no load & dry form, Sulphar content:- <2%(C) Back fill Compound

:- Earthing compound should be capable to retain moisture for

long time Necessary test report must be submitted by Agency.

(b)For Electrical installation up to 11 KV in normal

soil.Length of Pipe : 2.00 mtrs Back filling Compound :1 no.

59 Providing and fixing 01 units Automatic sliding Doors (2 leafs) of

size as per drawing for items to be fitted onto the Bus Station

excluding any other RF component.) with Four Door RF Controller

with 3 RFID Reader with weatherproof Stainless-Steel enclosure

to be fitted near the bus door with Emergency Door operations

Switche in Ticket office (inclusive of two-year warranty period) +

Four Door RF Controller (inclusive of two-year warranty period) +

RFID Reader with weatherproof Stainless-Steel enclosure to be

fitted near the bus door (inclusive of two-year warranty period) +

Emergency Door operations Switche in Ticket office (inclusive of

two-year warranty period) ( SD unit Per Station .Each Unit

comprise two leafs)

Total Electric Work

SIGNATURE OF THE CONTRACTOR.

EXECUTIVE ENGINEER

TRAFFIC BRTS PROJECT CELL

SURAT MUNICIPAL CORPORATION