Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹20.0 LAccepted-AOC | ₹20.0 L Quoted ₹21.9 L | L1 | Accepted-AOC Lowest bidder |
| 2 | L2₹22.8 L+₹91,815 (4.20%)Rejected-Finance | ₹22.8 L+₹91,815 (4.20%) | L2 | Rejected-Finance Other than lowest |
| 3 | L3₹30.4 L+₹8.6 L (39.3%)Rejected-Finance RAM SHIV COLONY GALI NO 2 NAIKA CHATNAG ROAD JHUNSI PRAYAGRAJ UP 211019 | PRAYAGRAJ | UTTAR PRADESH | 211019 | ₹30.4 L+₹8.6 L (39.3%) | L3 | Rejected-Finance Other than lowest |
| Sl No | Description | Qty | Unit | M/s Sheetal Associates L1 | TARA ENTERPRISES L3 | M/S MALHI CONSTRUCTIONS L2 |
|---|---|---|---|---|---|---|
| 1.00Servicing of Diesel Engine Generating sets of different rating as is to be carried out as per schedule given as under). :- B-Check :- (i) Change lubricating oil (ii) Change lubricating oil filters (iii) Change fuel filters (iv) Change coolent (v) Check engine wiring for damage (vi) Drain fuel supply tank (vii) Change by pass lubricant filters (viii) Change air filters (ix) (x) Check oil pressure (xi) Change fuel water separator C- Check :- (i) Adjust valves (ii) Steam clean engine (iii) Replace hoses as reqd (iv) Check turbo charger mounting nuts (v) Check engine oil heater (vi) Clean radiator (vii) Inspect following parts & replace as required (Alternator, starter etc) (viii) Clean fuel tank from inside (ix) Change Engine oil Note : (i) Maintenance of Diesel Engine Generating Set as per maintenance schedule chart . (ii) Schedule of service, Diesel Gen set M/C No wise is attached in PS. (III) Servicing of DG set will be done by Authorised dealer of Kirloskar/Cummins only. (iv) B-Check and C-Check spare parts will be measured and paid separately under supply only and fixing charges included with the servicing of DG set items i.e Item No 1 (1.1 to 1.08). | ||||||
| 1.01 | All as per item No-1.00 above but DG Set 7.5 KVA | 1 | Each Job | 2,500 ₹2,500 | 1,000 ₹1,000 Lowest | 4,000 ₹4,000 |
| 1.02 | All as per item No-1.00 above but DG Set 40 KVA | 4 | Each Job | 3,000 ₹12,000 | 1,500 ₹6,000 Lowest | 4,000 ₹16,000 |
| 1.03 | All as per item No-1.00 above but DG Set 62.5 KVA | 3 | Each Job | 3,500 ₹10,500 | 1,500 ₹4,500 Lowest | 5,000 ₹15,000 |
| 1.04 | All as per item No-1.00 above but DG set 75 KVA | 1 | Each Job | 4,500 ₹4,500 | 2,000 ₹2,000 Lowest | 5,000 ₹5,000 |
| 1.05 | All as per item No-1.00 above but DG set 82.5 KVA | 1 | Each Job | 5,500 ₹5,500 | 2,000 ₹2,000 Lowest | 5,000 ₹5,000 |
| 1.06 | All as per item No-1.00 above but DG set 160 KVA | 1 | Each Job | 8,000 ₹8,000 | 2,500 ₹2,500 Lowest | 6,000 ₹6,000 |
| 1.07 | All as per item No-1.00 above but DG set 140 KVA | 1 | Each Job | 9,000 ₹9,000 | 2,500 ₹2,500 Lowest | 6,000 ₹6,000 |
| 1.08 | All as per item No-1.00 above but DG set 250 KVA | 1 | Each Job | 9,500 ₹9,500 | 2,500 ₹2,500 Lowest | 7,500 ₹7,500 |
| 2.00 | Supply only new Fuel oil filter elements with 'O' ring for 7.5 KVA DG Set complete all as specified and as directed. Make: Kirloskar/Fleetguard/Cummins | 1 | Each | 500 ₹500 | 300 ₹300 Lowest | 800 ₹800 |
Tender Value
Refer Docs
EMD Value
₹80,000
Closing Date
10 Jul 2025, 6:00 pmClosed
Major S N Gaikwad
Holta Cantt Palampur
REPAIR MAINT OF E M INSTALLATION STAND BY DG SETS MOTORS AND REPLACEMENT OF LIGHTNING PROTECTION SYS IN MAGZINES OTHER BLDGS AND SOLAR LIGHT HIGH MAST LIGHT ALONGWITH OTHER CONNECTED WORKS AT PALAMPUR MIL STN
2025_MES_713983_1
GEP-35/2025-26
Open Tender
Civil Works
Item Rate
180 days
Palampur Mil Stn
As per tender documents
8 documents required · 8 mandatory
₹500
GE Palampur
₹80,000
1 Sept 2025
12 Jun 2025
17 Jul 2025
12 Jun 2025
10 Jul 2025
26 Jun 2025
Amount
Servicing of Diesel Engine Generating sets of different rating as is to be carried out as per schedule given as under). :- B-Check :- (i) Change lubricating oil (ii) Change lubricating oil filters (iii) Change fuel filters (iv) Change coolent (v) Check engine wiring for damage (vi) Drain fuel supply tank (vii) Change by pass lubricant filters (viii) Change air filters (ix) (x) Check oil pressure (xi) Change fuel water separator C- Check :- (i) Adjust valves (ii) Steam clean engine (iii) Replace hoses as reqd (iv) Check turbo charger mounting nuts (v) Check engine oil heater (vi) Clean radiator (vii) Inspect following parts & replace as required (Alternator, starter etc) (viii) Clean fuel tank from inside (ix) Change Engine oil Note : (i) Maintenance of Diesel Engine Generating Set as per maintenance schedule chart . (ii) Schedule of service, Diesel Gen set M/C No wise is attached in PS. (III) Servicing of DG set will be done by Authorised dealer of Kirloskar/Cummins only. (iv) B-Check and C-Check spare parts will be measured and paid separately under supply only and fixing charges included with the servicing of DG set items i.e Item No 1 (1.1 to 1.08).
All as per item No-1.00 above but DG Set 7.5 KVA
All as per item No-1.00 above but DG Set 40 KVA
All as per item No-1.00 above but DG Set 62.5 KVA
All as per item No-1.00 above but DG set 75 KVA
All as per item No-1.00 above but DG set 82.5 KVA
All as per item No-1.00 above but DG set 160 KVA
All as per item No-1.00 above but DG set 140 KVA
All as per item No-1.00 above but DG set 250 KVA
Supply only new Fuel oil filter elements with 'O' ring for 7.5 KVA DG Set complete all as specified and as directed. Make: Kirloskar/Fleetguard/Cummins
All as per item No-2.00 above but DG Set 40 KVA
All as per item No-2.00 above but DG Set 62.5 KVA
All as per item No-2.00 above but DG set 75 KVA
All as per item No-2.00 above but DG set 82.5 KVA
All as per item No-2.00 above but DG set 160 KVA
All as per item No-2.00 above but DG set 140 KVA
All as per item No-2.00 above but DG set 250 KVA
Supply only new Lubricant oil filter cartridge element with 'O' ring for 7.5KVA DG Set complete all as specified and as directed. Make : Kirloskar/Cummins/Fleetguard/Asoka /Mahindra
All as per item No-3.00 above but DG Set 40 KVA
All as per item No-3.00 above but DG Set 62.5 KVA
All as per item No-3.00 above but DG set 75 KVA
All as per item No-3.00 above but DG set 82.5 KVA
All as per item No-3.00 above but DG set 160 KVA
All as per item No-3.00 above but DG set 140 KVA
All as per item No-3.00 above but DG set 250 KVA
Supply only new By pass Lubricant Oil filter cartridge element with 'O' ring for 7.5 KVA DG Set complete all as specified and as directed. Make : Cummins/Fleetguard
All as per item No-4.00 above but DG Set 40 KVA
All as per item No-4.00 above but DG Set 62.5 KVA
All as per item No-4.00 above but DG set 75 KVA
All as per item No-4.00 above but DG set 82.5 KVA
All as per item No-4.00 above but DG set 160 KVA
All as per item No-4.00 above but DG set 140 KVA
All as per item No-4.00 above but DG set 250 KVA
Supply only new air filter (both outer & inner) element with 'O' ring for7.5 KVA DG Set complete all as specified and as directed. Make : Kirloskar/Cummins/Fleetguard
All as per item No-5.00 above but DG Set 40 KVA
All as per item No-5.00 above but DG Set 62.5 KVA
All as per item No-5.00 above but DG set 75 KVA
All as per item No-5.00 above but DG set 82.5 KVA
All as per item No-5.00 above but DG set 160 KVA
All as per item No-5.00 above but DG set 140 KVA
All as per item No-5.00 above but DG set 250 KVA
Supply only of fuel water separator filter complete with benjo bolt and washer for 7.5 KVA capacity DG Sets complete all as specified and as directed. Make : Cummins/Fleetguard
All as per item No-6.00 above but DG Set 40 KVA
All as per item No-6.00 above but DG Set 62.5 KVA
All as per item No-6.00 above but DG set 75 KVA
All as per item No-6.00 above but DG set 82.5 KVA
All as per item No-6.00 above but DG set 160 KVA
All as per item No-6.00 above but DG set 140 KVA
All as per item No-6.00 above but DG set 250 KVA
Supply only of Engine oil 15W40 grade in DG Set complete all as specified and as directed. Make : K OIL SUPER BY KIRLOSKAR/Castrol/Servo.
Supply only of Coolent of DG Set complete all as specified and as directed. Make-K COOL BY KIRLOSKAR/Castrol/BOSCH
Supply only V-Belt off sizes, complete all as per site requirement complete all as specified and as directed.
Supply only of Oil pressure gauge ISI mark complete all as specified and as directed.
Supply only of oil temperature gauge ISI mark complete all as specified and as directed.
Supply only of Fuel gauge meter ISI mark operated on 24V DC complete all as specified and as directed.
Supply only of high temprature diesel Hose pipe of 1000 PSI of size 12.5mm dia for connecting from diesel tank outlet to Engine complete with banjo bolt & washer.
Supply only of high temprature diesel Hose pipe of 1250 PSI of size 10.3mm dia for connecting from engine to diesel tank complete with banjo bolt & washer.
Supply only of distilled water for battery complete all as directed
Dismantling /taking down complete radiator assy from DG set form diffrent capacity and transport to workshop for cleaning of the same with suitable cleaning reagent to remove rust & scaling , plugging of any water leakage by brazing and refixing including replacement of rubber hose pipe complete with jupiter clamps for any capacity of DG Sets, complete all as specified and as directed.
M&L for dismantling of Exhaust pipe of silencer, cleaning of silencer to remove carbon deposit inside exhaust pipe and refixing including replacement of worn out rubber gasket packing and nut,bolts including replacement of asbestos rope 20mm complete all as specified and as directed.
Dismantling of defective dynamo from engine, supplying and fixing new dynamo 24 Volt DC Make- TVS Lucas,inclding replacement of worn out nuts bolts mounting clamp etc. complete all as specified and as directed.
Dismantling of self starter 24V DC by disconneting battery connection , taking out to civil workshop for carrying out following reapair work and refixing including testing complete:- (i) Rewinding of armature & Field coil.(ii) Replacement of Carbon brush and solenoid switch (iii) Replacement of gear assembly .
Supplying and replacement of Digital meter square type 96x96mm suitable for measuring 3-ph combined voltage, ammpere & frequency simultaneously in three independent windows with ultra LED display complete . Make Neptune/AE
Supply and fixing 440Volt DC 24 V relay suitable for 140KVA/250 KVA DG Set complete all as specified
Supply and fixing 220Volt AC 24 V relay suitable for 62.5 KVA/100 KVA DG Set complete all as specified
Supplying and replacement self starter 12 Volts DC suitable for DG Set 63/82.5/100 KVA Make -LUCAS/BOSCH
Supplying and replacement self starter 24 Volts DC suitable for DG Set 160/200/250 KVA Make -LUCAS/BOSCH
M&L for spray painting to Panels, Enclosure of DG sets, fire stand post duct plates etc at DG installations with two coats of synthetic enamel paint of approved colour after making the suface free from oil/grease/rust and applying a coat of red oxide primer complete all as specified and as directed.
Supply and fixing Battery 12V, 180 AH with 25 Nos Electro plates including battery lead positive & negative battery terminal complete duly charged . Make Exide (Brand : Exide Express) or equivalent in Amron/Prestolite
Supply and fixing Battery 12V, 150 AH with 25 Nos Electro plates including battery lead positive & negative battery terminal complete duly charged . Make Exide (Brand : Exide Express) or equivalent in Amron/Prestolite
M & L for Door joint and handle locks arrangement for any size/capacity DG set complete all as specified and directed.
Opening the coupling of DG set of capacity 160KVA /250 KVA the outer cover and taking out the fly wheel ring and shifting to workshop for repair in and including replacement of fly wheel ring by prressing machine and reinstalled the same after repair to make it fully functional complete all as specified.
Opening the coupling of DG set of capacity 40KVA /82.5 KVA the outer cover and taking out the fly wheel ring and shifting to workshop for repair in and including replacement of fly wheel ring by prressing machine and reinstalled the same after repair to make it fully functional complete all as specified .
Supply and replacement of compact type panel mounted battery charger suitale for charging 02 Bty, 12 V 180 AH Each complete all as speified and directed with 2m copper leads -02 Nos & brass clamps.
Supply and replacement of compact type battery charger unit suitale for charging 01 Bty ,12 V 180 AH complete all as speified and directed with 2m copper leads -02 Nos & brass clamps.
Taking out FIP from DG set , of cap 63 /250KVA transportation to authorised service centre for repair /maintenance and refixing to DG set including replacement of necessary spare parts such as Plunzers, governer kit with pin , Nozzels , Head ball guide kit, Head sheet , Rock rod, Rollar bearing , oil seal, piston & rings pin, jain kit and sleeves complete all as directed and specified.
M&L cleaning of diesel tank of DG set of any capacity including replacement of worn out pipe line and measuring scale and fixing in original position and make it leak proof with necessary clamps complete all as specified and directed.
Supply of Battery Terminal Copper (Positive & Negitive) complete
Supply fixing in repairs battery lead (Red colour), PVC insulated multistranded , copper conductor 70sqmm, each 1.25 mtr long, duly fixed with brass clamps, copper lugs complete all as specified
Supply fixing in repairs battery lead (Black colour), PVC insulated multistranded , copper conductor 70sqmm, each 1.25 mtr long, duly fixed with brass clamps, copper lugs complete all as specified
M&L for earthing with steel earth plate electrode of size 60x60cmx6mm thick buried directly in ground to a depth not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to GI strip of size 32x6mm as earthing lead by means of nuts, bolts and washers of galvanized iron or steel after welding of GI strip to earth electrode to the full lenght of earth plate, 40mm dia GI tubing light grade protection pipe upto test point, 20mm dia GI watering pipe med grade with funnel and wire mesh, PCC pit 1:3:6 with pit cover of size 30X30cm made of RCC 1:3:6 with suitable handle,angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling in all as required at site including test point made out of steel plate of size 75x75x6mm fixed to wall all as specified in plate No 3 of SSR Part-I and directed by Engr-In-Charge.
M&L for provn of Earthing complete with Copper earth plate electrode 600 x 600 x 3 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the plate not less than 1.50 M below normal GL, connected to copper earth strip 25 x 3.15 mm upto 7.5 mtr protection pipe by means of copper bolts, nuts, check nuts & washers incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 40mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No.3 of SSR Pt-I specification. Note :- (i) The excess requirement (if more than 7.5 Mtr) of copper strip, GI protection pipe 40 mm dia and their joints for connecting upto the test point will be measured and paid separately) (ii) The excavation exceeds if any of the above will be deemed to be included in the item rate.
Taking out unserviceable asbestos rope from the exhaust pipe cleaning the exhaust pipe supply and wraping new asbestos rope of suitable size and wrapping with wire mesh and plasterig withplaster of paris /white cement for smooth finishing including replacement of gasket and tightening of all nut and bolts all as directed by the Engineer-in -Charge
Supply & Fixing in replacement water pump assembly complete all as specified and directed.
Supply & Fixing in replacement Lubrication oil pump assembly complete all as specified and directed.
Supply & Fixing in replacement Lubrication oil pipe complete all as specified and directed.
Supply & Fixing in replacement lever forstopping of engoine as per site requirement for DG set complete all as specified and directed.
Supply and fixing in repairs automatic voltage regulator up to 82.5 KVA as per sample complete all as specified and directed.
Supply and fixing in repairs automatic voltage regulator suitable for 100 KVA to 250 KVA as per sample complete all as specified and directed.
Supply and fixing in repairs automatic voltage regulator suitable for 250 KVA as per sample complete all as specified and directed.
Supply & Fixing in replacement MCCB 125 Amp 16 KA, 3 pole, adjustable type all as specified and directed.
Supply & Fixing in replacement MCCB 160 Amp 36KA,3 pole, adjustable type all as specified and directed.
Supply & Fixing in replacement MCCB 200 Amp 36KA, 3 pole, adjustable type all as specified and directed.
Supply & Fixing in replacement MCCB 250 Amp 36 KA, 4 pole, adjustable type all as specified and directed.
Supply & Fixing in replacement MCCB 400 Amp 36KA, 4 pole, adjustable type all as specified and directed.
Supplying and fixing of On-load type Changeover switch 250 Amp, 4-pole, 415 volt, open execution type complete all as specified and as directed. Make: Havells/L&T/BCH/Schneider
Supplying and fixing of Off-load type Changeover switch 100 Amp, 4-pole, 415 volt, with enclosure type complete all as specified and as directed. Make: Havells/L&T/BCH/Schneider
Supplying and fixing of Off-load type Changeover switch 125 Amp, 4-pole, 415 volt, with enclosure type complete all as specified and as directed. Make: Havells/L&T/BCH/Schneider
Supplying and fixing of Off-load type Changeover switch 200 Amp, 4-pole, 415 volt, with enclosure complete all as specified and as directed. Make: Havells/L&T/BCH/Schneider
Supplying and fixing of Off-load type Changeover switch 250 Amp, 4-pole, 415 volt, with enclosure complete all as specified and as directed. Make: Havells/L&T/BCH/Schneider
Excavation in trenches in any type of soil not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for laying of cables, erection of poles,struts, stays etc and getting out all as specified and as directed by Engr-In-Charge.
Returning, filling in including spreading, levelling,watering and well ramming excavated soil in layers not exceeding 25 cm thick each , filling back in trenches after cables have been laid and tested, poles,stays,struts hane been erected and tested complete all as specified.
Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified.
M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed by Engr-in-Charge.
M&L for laying in trenches burnt brick sub class 'B' for cable protection laid adjacent to each other length wise perpendicular to the central axis of cable complete all as specified.
Taking down old unserviceable underground cable and type and size
Supply & laying of UG cable XLPE insulated armoured heavy duty elect cable with stranded aluminium conductor 1100 volts grade cross section area 95 Sqmm 3.5 core laid in trenches/ fixing on panels/walls/poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing complete all as specified and directed.
All as per item No. 65 above but of cross sectional area 70 Sqmm, 3.5 core complete all as specified and directed.
All as per item No.65 above but of cross sectional area 50 Sqmm, 3.5 core complete all as specified and directed.
All as per item No. 65 above but of cross sectional area 35 Sqmm, 3.5 core complete all as specified and directed.
All as per item No. 65 above but of cross sectional area 25 Sqmm, 3.5 core complete all as specified and directed.
All as per item No. 65 above but of cross sectional area 16 Sqmm, 4 core complete all as specified and directed.
M&L for demolition concrete of any description and any position not otherwise specifically provided for floor plinth protection or hard standing complete.
M&L Plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete for stays foundation and platform for transformer installation complete all as specified and directed.
M&L Plain cement concrete 1:4:8, Type D-2 by using 40 mm graded granite stone aggregate for base (bottom of pit for Bed Concrete) including necessary form work and finishing exposed surfaces fair & even complete all as specified and as directed.
M&L Plain cement concrete 1:2:4, Type B-1 by using 20 mm graded granite stone aggregate in coping including necessary form work and finishing exposed surfaces fair & even complete all as specified and as directed.
M&L for providing cement concrete in surface of ground and making good disturbed surfaces as it was existing by using the PCC 1:2:4 type B2 with 40 mm graded aggregate on cutting areas/ disturbed surfaces complete.
Supply and fix power contactor 3-pole, 150Amp, 440V rating MCX41 type all as Cat Part No LC1D150M7 Make : Schneider or equivalent in L& T ,C&S/Havells make.
Supply and fix coil suitable for MCX41 power contactor all as Make : L&T or equivalent in C&S/Havells make.
Supply and spread graded stone aggregate of 40mm to 63 mm nominal size around outdoor transformer and two/four pole structure /panel complete all as specified and directed
M & L for GI Pipe medium grade 100mm bore for cable protection in floor/road crossing/along pole complete all as specified and as directed.
M & L for GI Pipe medium grade 80mm bore for cable protection in floor/road crossing/along pole complete all as specified and as directed.
M&L for removal green vegetation and dressing around the plinth/PCC hardstanding up to 1.5 mtr of sub stations and 2/4 pole structure etc including disposal of vegitation /material up to 50 mtr distance from the site and levelling/surfacing the ground all as specified and as directed by Engr-in-Charge.
Supply and fix MS Chequred plate 6.0 mm thick sheet having with Hook, and painting it with one coat of black paint suitable for cable duct cover in pump house and sub stn complete all as specified and directed
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material (Epoxy Based) and accessories suitable for 3½/ 4 core XLPE armoured Al conductor cable of size 70 to 95 sq mm complete all as specified and as directed.Make : Denson/M-seal
S&F bus bar chamber TPN suitable for 63A TPN Copper bus bar with four outgoining ways complete allas specified and directed
S&F bus bar chamber TPN suitable for 100A TPN Copper bus bar with four outgoining ways complete allas spoecified and directed
S&F DG Set control panel display suitable for 40 to 63.5 KVA DG set complete all as specified and directed
Supply & Fixing Air termination, single pointed aluminium rod 12mm dia and 300mm long, complete all as specified and as directed.
Supply and fixing Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw, complete all as specified and as directed.
Supply and fixing for Aluminium strip of size 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground., complete all as specified and as directed.
Supply and fixing of Galvanised iron strip of size 32 x 6mm buried in ground., complete all as specified and as directed.
M&L Checking of Earth Resistance of GI/Copper /Chemical/Normal Earthing and maintaining the the resistance as required Earth Resistance Tester will be provided by the Contractor. and will be recorded in Register, same will be put up to the Engineer-in-Charge . Contractor will be responsible for pouring of water in the Earth Pits at his own arrangement with Water Tanker, etc. However, Water will be provided by the Department. complete all as specified and directed by Engr in Charge.
M&L Taking out loose/displaced Serviceable Aluminium Strip/ Copper Strip/ GI Strip of any size and any description with Accessories and refixing the same with necessary Fixing Arrangement like Screws, Saddles, Nuts and Bolts, complete all as specified and as directed. NOTE : Cost of Screws, Saddles, Nuts and Bolts, etc. will deemed to be included in the Quoted Unit Rate.
M&L for replacement Maintenance Free UL approved Copper Bonded Earth Rod of 10 Feet length 17.2mm dia made of High Tensile Low Carbon Steel Rod, molecularly bonded with 99.9% Electrolyte Grade Copper on outer surface (minimum copper bonding thickness-250 microns) jointed with Copper Bus Bar of size 50x6x200mm with Exothermic joint, complete all as specified and as directed by Engr in charge
M&L for supply and pouring of RoHS tested Earth Enhancement Compound after mixing with water tested by NABL accredited lab in compliance to IEC 62561-7 with a resistivity < 0.12 ohm-m. It shall be free from bentonite and other hazardous substances. It shall be a permanent, non-corrosive material and will not leach any chemicals into the ground. It shall retain moisture even in high soil resistivity areas. complete all as specified and as directed. Note: Measurement of Chemical will be done in Powder form.
Supply and fixing of Copper Strip 20x3.15mm with Saddles and fixing Screws for Roof/ Earth Conductors and Down Conductors above Ground, complete all as specified and as directed.
Supply & Fixing porcelain insulator of required size not exceeding than 10 cm long with two nos hole each on both end for fixing properly with fastner, nuts & bolts on wall & roof of buildings for separated earthing stirp from building all as required at site & directed by Engineer in Charge. Note : (i) Water leak protection has to be ensured, Pure Resin based Chemical anchoring system.
Material and labour for overhauling of existing 16 /20meters height high mast lighting system by degreasing and cleaning of double drum winch, gear box, wire rope, clamp, bobbin arrangement, power tool motor, mechanical torque limiter, lowering the high mast head assembly, degreasing and cleaning the pulley, docking arm etc and applying new grease / lubricating oil for all mechanical moving / rotating parts, checking all the electrical parts such as timer panel, cable connections in control panel, motor, junction box, flood light fittings and aviation obstruction light fitting including testing for proper functioning complete all as specified and directed by Engineer-in-Charge. Note: Defective spare parts shall be measured and paid seperatelly. The servicing/Maintanance of the system will be carried out through authorised dept.
M&L for Painting to the existing solar street light system including pole, battery box, bracket etc complete with two coats and painted in silver ash hammer tone colour all as specified and directed by Engineer-in-Charge.
Supply and fix in replacement of unservicable battery 12.5 volt, 30Ah lead acid battery type duly charged complete all as directed by Engr-in charge
Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp
S&F surge protection device sitable for LED flood light fitting complete all as specified
M&L for repair to suspension system of high mast light servicing , greasing and cleaning and testing for proper functioning of suspension system complete all as specified and directed by Engr in Charge
M&L for dismentling motor from high mast light and bring it to civil workshop for servicing and overhaulling of motor and replacement defective parts including testing and efixing the same at site complete all as specified and directed by Engr in charge.
Supply and fix in replacement of Integral LED aviation light 6watt , 500 mmwith IP 65 protection fitting comprising of aluminium housing with polycarbonate enclosure including taking down existing unserviceable aviation light of any description complete all as specified and directed by Engineer-in-Charge.
M&L for repair to suspension system of high mast light servicing , greasing and cleaning and testing for proper functioning of suspension system complete all as specified and directed by Engr in Charge
Supply and fixing outdoor type control with Photo Sensitive smart sensor LED street light fitting 90 Watt 230 V AC outdoor type & high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impactand corrosion resistant including thermal management in multiple optics & suitable connection with photoelectric sensor complete with IP 65/66 protection complete all as specified
Supply & Fixing LED driver suitable for LED street light fittings of 90 watt complete
Supply and fixing LED driver suitable for LED street light fittings of 120 watt complete
Supply and fixing PCB Card suitable for Multi LED Light Fitting of capacity 90 Watt complete all as specified and as directed.
Supply and fixing PCB Card suitable for Multi LED Light Fitting of capacity 120 Watt complete all as specified and as directed.
Supply and fix in repairs, flexible stranded copper conductor cable PVC insulated and PVC sheathed twin core of size 1.5 Sqmm
S & F 12 Volt 75 Wp solar panel module complete suitable as per site all as specified and directed by Engr-in Charge
S & F in replacement of solar/street light bracket arm fabricated out of 40 mm dia GI tubing light grade 1.2 mtr long bend to shape fixed to pole with 2 pair of clamps of fitted with suitable size nuts, bolts washers incl one coat of paint all as specified and directed
Supply , fixing and testing of LED solar street light complete set including 30 watt LED luminair with inbulit solar charge controller and PIR motion sensor for motion detection , 75 Wp solar photovoiletic module , 30 Ah battery LMLA tubular low discharge long life battery , battery box with pole 6 meter long made of GI with adequate thickness corresion free with IP 65 protection with complete wiring and other accessories required complete all as specified and directed by Engr -in-charge
M&L for replacement of PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) with Cast iron cover 10mm thick hinged, Cast Iron Frame, MS Rod 6mm, Funnel as shown in Electrical Plate No 3 of MES Schedule Part-I including excavation work required at site, complete all as specified and as directed.
M&L for replacement of Pre-cast RCC Cover with Handle 2 Nos and hole of dia 40mm in Cement Concrete 1:2:4 (20mm graded stone aggregate) of size 540x540x60mm, reinforced with and including 10mm dia TMT Bars @ 250mm Centre to Centre in both ways, complete all as specified and as directed.
M&L for lightening conductor assembly made out of GI pipe light grade of size 50 mm bore along with welded flange, fixed on the RCC roof of the bldgs with drilling/making hole and provide fastners, rubber washer 6 mm thick of suitable size at one end & GI reducer socket 50 x 40mm at another end connected with GI pipe light grade of size 40 mm bore with one end GI reducer socket to connect air termination & connector for earth strip duly fixed with necessary fastners, nuts bolts & washers in PCC 1:2:4 type B0 45cm x 45cm x45cm complete all as directed by Engr-in-charge. Note : GI pipe 50mm (1.5 RM for each)/40MM (1.0 RM for each) & air temination shall be measured & paid separately under relevant items. (ii) Water leak protection has to be ensured.
M&L for lightening conductor assembly fixed on the AC Sheet roof with drilling/making hole and provide rubber washer 6 mm thick of suitable size to connect air termination & connector for earth strip duly fixed with necessary nuts, bolts, washers making leaking proof to roof complete all as directed by Engr-in-charge. Note : Air temination shall be measured & paid separately under relevant items
Suppl and fix lightening conductor protection rod with followng spacification :- (a) Height of primary terminal =1000mm (b) Diameter of Rod = 22.25mm (c ) Tip of Rod = Tapered tip/sharp tip (d) Secondary terminal - Shall attached to bowl ( e) Dimension of bowl - 125 mm wide x 4 mm thick (f) Direction = Facing the primery terminal on 4 sides ( g) Electrolyte = Copper (h) Additional protection = Nickel plated tie for corrosion resistance and side flash capture (j) Confirmation = IEC 62305 (k) Construction = Protection system shall consist of one primary and four secondary air terminal . The primary air terminal is a vertical conductive rod having a sharp tip at one end the secondary air terminal (04 Nos) formed on a bowl shaped circular disc are fixerd on vertical rodes further the actual points of the scecondary terminals are spaced and placed in such a way to receive the maximum side flashes work shall be executed complete all as specified and directed by Engr -in -charge (l) ISO certification = ISO 9001:2015 (m) Current capacity (Tested) = 40 KA (n) Dia of SFCH = 125mm (o) Base plate dimension (mm) = 150 x150 x6 complete all as specified and as directed
M&L for boring in loose/soft soil upto 200mm dia, by means of hand/ machine drill, upto 3 Meter depth from ground level and pouring of sufficient water for at least 3 times per day for two days and making hole under reference ready for pouring of chemical complete all as specified and as directed.
Supply & Fixing HDPE DWC pipe for DG Set cable of 50 to 95 Sqmm for protection all as specified and directed
M/S MALHI CONSTRUCTIONS (BID ID -3354059)
TARA ENTERPRISES (BID ID -3349937)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .