REPAIR, PAINTING, POLISHING AND MISC ITEMS OF VARIOUS STEEL/ IRON/ WOODEN FURNITURE AT NHO AND CLEMENT TOWN UNDER GE CLEMENT TOWN

Amount

TABLE DINING ORS FD-165(M)

Removing old unserviceable top and S&F new table Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE with wooden edging and headless nails all round the edges all as specified and directed.

Removing of unserviceable long rail/stiffner and S & F new long rail/stiffner of conduit pipe 25 mm 1.6 mm thick as per drawing.

Removing of unserviceable short rail/stiffner and S & F new short rail/stiffner of conduit pipe 25 mm 1.6 mm thick as per drawing.

Removing of unserviceable legs rail and S & F new legs of conduit pipe 25 mm 1.6 mm thick as per drawing.

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M & L for welding to broken steel frame of Table Dining ORS.

M&L for preparation of old painted iron & steel surfaces of table dining ORs by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

ALMIRAH LARGE STEEL FD-67/104/1031 & /FD/E6/MAP/18

Removing of old unserviceable handle without damaging the adjacent parts of almirah large steel and S & F new steel CP handle 125 mm long of approved quality all as specified and directed

Removing of unserviceable lock without damaging the adjacent parts of almirah large steel and S&F new lock of size 65 mm with duplicate keys to almirah large steel (Make : Godrej/Hetich/Harrison) 6 lever complete all as directed and as shown in drg.

Removing unserviceable locking device and S&F new almirah large steel locking device of 10 mm dia including MS Rod and brass shackles complete with fixing accessories complete all as shown in drawing and as specified and directed

Adjustment/fixing of the existing loose shelves by providing new clamps, cleats, screws etc removing unserviceable clamps all as directed (Cost of cleats, clamps, screws shall deemed to be included in quoted rate)

Taking out unserviceable hinges S&F new hinges of reqd size as per drg.

Taking out unserviceable broken legs from Almirah large steel and S&F new legs made out of 1 mm MS sheet suitable for almirah large steel & welded accordingly complete all as directed and as shown on drg.

Taking out old unserviceable/damaged shelves of almirah large steel and S&F new shelves made out of 1mm MS sheet bent to required shape and fixing the same properly in position complete all as directed

Taking out unserviceable shutters/Covers and S&F almirah large steel new shutters/covers made out of 1mm MS sheet made to required size and shape as per drawing suitable for three way locking device and fixed with suitable size of MS Screws complete all as directed.

M & L for welding to broken steel frame of almirah large steel with shelves

M&L for preparation of old painted iron & steel surfaces (Externally and internally including shelves etc) of almirah large steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge. (Cost of paint shall deemed to be included in quoted rate)

ALMIRAH MEDIUM/SMALL STEEL WITH SHELVES FD-67/243/1032

Removing of old unserviceable handle without damaging the adjacent parts of almirah medium steel and S & F new steel CP handle 125 mm long of approved quality all as specified and directed

Removing of unserviceable lock without damaging the adjacent parts of almirah medium steel and S&F new lock of size 65 mm with duplicate keys to almirah medium steel (Make : Godrej/Hetich/Harrison) 6 lever complete all as directed and as shown in drg.

Removing unserviceable locking device and S&F new almirah medium steel locking device of 10 mm dia including MS Rod and brass shackles complete with fixing accessories complete all as shown in drawing and as specified and directed

Adjustment/fixing of the existing loose shelves by providing new clamps, cleats, screws etc removing unserviceable clamps all as directed (Cost of cleats, clamps, screws shall deemed to be included in quoted rate)

Taking out unserviceable hinges S&F new hinges of reqd size as per drg.

Taking out unserviceable broken legs from Almirah medium steel and S&F new legs made out of 1 mm MS sheet suitable for almirah medium steel & welded accordingly complete all as directed and as shown on drg.

Taking out old unserviceable/damaged shelves of almirah medium steel and S&F new shelves made out of 1mm MS sheet bent to required shape and fixing the same properly in position complete all as directed

Taking out unserviceable shutters/Covers and S&F almirah medium steel new shutters/covers made out of 1mm MS sheet made to required size and shape as per drawing suitable for three way locking device and fixed with suitable size of MS Screws complete all as directed.

M & L for welding to broken steel frame almirah medium/small steel with shelves.

M&L for preparation of old painted iron & steel surfaces (Externally and internally including shelves etc) of almirah medium steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge. (Cost of paint shall deemed to be included in quoted rate)

LOCKER STEEL FD-257/1029

Removing old unserviceable broken handle from locker steel without damaging adjacent parts of locker bed side steel and S&F new CP steel handle 100 mm long of approved quality complete all as specified and directed

Removing old unserviceable hasp and staple w/o damaging the adjacent parts of locker steel and S&F new hasp and staple chromiun plated of suitable size complete all as specified and directed by Engr in Charge.

Taking out old unserviceable broken hinges from locker bed side steel without damaging adjacent parts of locker bed side steel and S&F new hinges of reqd size of approved quality complete all as specified and directed.

Taking out unserviceable broken legs from locker steel and S&F new legs made out of 1 mm MS sheet suitable to locker steel & welded accordingly complete all as specified and directed.

Taking out unserviceable shelves and S&F new shelve made out of 1mm MS sheet as per drawing including fixing of existing loose shelves by providing new cleats, clamps, screws etc. Rest all as specified and directed.(Cost of cleats, clamps, screws shall deemed to be included in quoted rate)

Taking out unserviceable shutters and S&F new shutters made out of 1mm MS sheet as per drawing.

Taking out unserviceable conduit pipe and S&F new CP conduit pipe 20 mm dia of 1.6 mm thick as per drawing.

M & L for welding to broken steel frame of locker steel wherever required.

M&L for preparation of old painted iron & steel surfaces (Externally and internally including shelves etc) of locker steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TABLE 3'x2' STEEL FD-1007,1008

Removing old u/s broken top and S&F new table Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE with wooden edging and headless nails all round the edges all as specified and directed

Taking out unserviceable leg and S&F new leg made out of MS conduit pipe 25 mm dia of 1.6 mm thick as per drawing.

Removing of unserviceable short rail/stiffener and S & F new short rail/stiffener of conduit pipe 25 mm 1.6 mm thick as per drg.

Removing of unserviceable long rail/long stiffner and S & F new short rail/stiffner of conduit pipe 25 mm 1.6 mm thick as per drg.

Removing the existing unserviceable locks of drawer of table 3' X 2' with drawer and S&F new lock (Make : Godrej/Hetich/Harrison) 5 lever of suitable size with duplicate keys complete all as specified and directed

Removing of old broken unserviceable drawers from existing table 3' X 2' with drawer and S&F new drawers as per drawing complete all as specified and directed

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M & L for welding to broken steel frame of table 3'x2' with drawer

M&L for preparation of old painted iron & steel surfaces of table 3' X 2' steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TABLE STEEL FD-1006/1010/1011/1012/1013/1016/1019

Removing old u/s broken top and S&F new table Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE with wooden edging all around and headless nails all round the edges all as specified and directed

Taking out unserviceable leg and S&F new leg made out of MS conduit pipe 25 mm dia of 1.6 mm thick as per drg.

Removing of unserviceable short rail/stiffner and S & F new short rail/stiffner of conduit pipe 25 mm 1.6 mm thick as per drg.

Removing of unserviceable long rail/long stiffner and S & F new short rail/stiffner of conduit pipe 25 mm 1.6 mm thick as per drg.

Removing of unserviceable shoe and S & F new hard rubber shoe as per drawing.

M & L for welding to broken steel frame of table steel

M&L for preparation of old painted iron & steel surfaces of table steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TABLE 3'x3' STEEL FD-1009,1014

Removing old u/s broken top and S&F new table Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE with wooden edging all around and headless nails all round the edges all as specified and directed

Taking out unserviceable leg and S&F new leg made out of MS conduit pipe 25 mm dia of 1.6 mm thick as per drawing.

Removing of unserviceable rail and S & F new rail of conduit pipe 25 mm 1.6 mm thick as per drg.

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M & L for welding to broken steel frame of table 3'x3' steel

M&L for preparation of old painted iron & steel surfaces of table 3' X 3' steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TABLE OFFICE CLERK STEEL FD-84/1004

Removing old u/s broken top of table office clerk steel and S&F new table Top of suitable size shall be made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa/) ISI marked confirming to IS-14587 Grade-I one side with approved shade and balancing white lamination on other side with wooden edging all around and headless nails all round the edges all as specified and directed and as per drawing

Taking out unserviceable leg and S&F new leg made out of MS conduit pipe 25 mm dia of 1.6 mm thick as per drawing.

Adjustment of drawers where ever reqd as directed by Engr in Charge

Removing unserviceable locks of drawer and S&F lock (Make : Godrej/Hetich/Harrison) 5 lever as per drg.

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M & L for welding to broken steel frame of table office clerk steel.

M&L for preparation of old painted iron & steel surfaces of table office clerk steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TABLE OFFICE OFFICER STEEL FD-1002/1003

Removing old u/s broken top of table office officer steel and S&F new table Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE with wooden edging all around and headless nails all round the edges all as specified and directed

Taking out unserviceable leg and S&F new leg made out of MS conduit pipe 25 mm dia of 1.6 mm thick as per drawing.

Removing the existing unserviceable locks of drawer of table office officer steel and S&F new lock (Make : Godrej/Hetich/Harrison) 5 lever of suitable size with duplicate keys complete all as specified and directed

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M & L for welding to broken steel frame of table office officer steel

M&L for preparation of old painted iron & steel surfaces of table office officer steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TEAPOY VERANDAH FD-383, FD/E6/MAP/17

Removing old u/s broken top and S&F new Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE with wooden edging all around and headless nails all round the edges all as specified and directed

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M & L for preparation of old steel surface of teapoy verandah and welding loose points, if any including de-rusting the surface and painting with two coat of synthetic enamelled paint (1st grade quality) complete all as specified and directed

BOOK CASE STEEL FD-1028

M&L for removing old worn out Shelf from the Book Case Steel Supply and S&F new shelf made out of 1 mm thick MS Sheet . Rest all as specified on drg and as directed by Engr in Charge.

M&L for removing old worn out Shutters from the Book Case steel Supply and S&F new Shutter made out of 1 mm thick MS Sheet with 3mm plane glass . Rest all as specified on drg and as directed by Engr in Charge.

M&L for removing old worn out lock from the Book Case steel Supply and S&F new lock (Set of four lock with one set of key)(Make : Godrej/Harrison/Link). Rest all as specified on drg and as directed by Engr in Charge.

M&L for removing old worn out handle from book case steel supply and S&F new handle of best quality . Rest all as specified on drg and as directed by Engr in Charge.

M & L for welding to broken steel frame of Book Case Steel.

M&L for preparation of old painted iron & steel surfaces of book case steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

BOOKSHELF OPEN /RACK STEEL (ANY TYPES) FD-69(M)/129/106 /1038 /1039

M&L for removing old worn out Shelf from the Rack Steel (Any Types) and S&F new shelf made out of 1 mm thick MS Sheet . Rest all as specified on drg and as directed by Engr in Charge.

M&L for removing old worn out angle iron from the Rack Steel (Any Types) and S&F new slotted angle iron of of required size and length with suitable nuts and bolts . Rest all as specified on drg and as directed by Engr in Charge.

M&L for removing old worn out sides from the Rack Steel (Any Types) and S&F new Sides made out of 1 mm thick MS Sheet . Rest all as specified on drg and as directed by Engr in Charge.

M&L for removing old worn out back from the Rack Steel (Any Types) and S&F new back made out of 1 mm thick MS Sheet . Rest all as specified on drg and as directed by Engr in Charge.

M&L for preparation of old painted iron & steel surfaces of rack steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

CHAIR REVOLVING/CHAIR EXECUTIVE TP & FD/E6/MAP/01

Removing the existing old unserviceable seat and back from the chair and re-upholestering with new fabric containing material like Acrylic polyester, poly viscose, poly propylene of colour as approved by GE on PU foam of 50 mm 50 density fixed over 12 mm BWR plywood all as specified on drg and as directed by Engr in Charge. (Fabric shall be as per sample kept in yard)

Removing the existing unserviceable or broken castor wheel and S&F New Castor wheel to the chair in suitable pattern/model to match the original all as specified on drg and as directed by Engr in Charge.

Removing the existing broken/ unserviceable handle from the chair and S&F new handle made out of Black Integral Skin Polyurethene reinforced with MS insert scratch and weather resistant to the chair in suitable pattern/model to match the original all as specified on drg and as directed by Engr in Charge.

Removing the existing unserviceable or worn out bottom base from the Chair. Supply and fix new Base to the chair in suitable pattern/model to match the original all as specified on drg and as directed by Engr in Charge.

M & L for welding to broken steel frame of Chair revolving/Chair Executive.

Gas lifting Hydraulic System : Removing the existing unserviceable Gas lifting Hydraulic System of various types from the Chair. Supply and fix new maintenance free, environmental friendly, chrome free cylinder tube fixed in a M.S. black powder coated with outer central column tube 38 mm dia and 2 mm thick having 100 mm storke length with gas pressure of 300 n force Gas lifting Hydraulic System to the chair in suitable pattern/model to match in original all as specified on drg and as directed by Engr in Charge.

CHAIR WRITING FD/E6/MAP/12

Removing the existing old unserviceable seat and back from the chair and re-upholestering with new fabric containing material like Acrylic polyester, poly viscose, poly propylene of colour as approved by GE on PU foam of 50 mm 50 density fixed over 12 mm BWR plywood with PVC lipping all around all as specified on drg and as directed by Engr in Charge. (Fabric shall be as per sample kept in yard)

Removing the existing broken/ unserviceable armrest from the chair and S&F new armrest made out of Black Integral Skin Polyurethene reinforced with MS insert scratch and weather resistant to the chair in suitable pattern/model to match the original all as specified on drg and as directed by Engr in Charge.

Removing old u/s rubber stopper and S&F new rubber stopper superior quality as approved by GE shall be provided.

M & L for welding to broken steel frame of Chair revolving/Chair Executive.

M&L for preparation of old painted iron & steel surfaces of Chair writing by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

BED HARD FD/E6/MAP/08(R)

Removing old u/s top and S&F new top of plywood (Make: Greenply/Century/Archidply) top 12mm thick BWR Grade ISI Marked confirming to IS-303 of Bed plywood (Make: Greenply/Century/Archidply) made to shape & size as shown on drawings, complete all as specified and directed by GE.

Removing old u/s headrest and S&F new headrest made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE. All as directed by GE and shown on drawing.

Removing old u/s footrest and S&F new footrest made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE. All as directed by GE and shown on drawing including dismatling of old unserviceable top without disturbing the other parts.

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M & L for welding to broken steel frame of Bed Hard.

M&L for preparation of old painted iron & steel surfaces of bed hard by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TABLE BED SIDE FD/E6/MAP/15(R)

Removing old u/s broken top of table bed side and S&F new Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE including all round wooden beading fixed with fevicol and headless nails complete all as specified and directed.

Removing old u/s top drawer of table bed side and S&F new Top drawer of suitable size. The front of drawers shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE. The sides and back of drawer shall be made with 12mm thick BWR grade plywood (Make: Greenply/Century/Archidply). The bottom of drawer shall be made of 6mm thick BWR plywood (Make: Greenply/Century/Archidply)

Removing old u/s bottom drawer of table bed side and S&F new bottom drawer made of suitable size. The front of drawers shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE. The sides and back of drawer shall be made with 12mm thick BWR grade plywood (Make: Greenply/Century/Archidply). The bottom of drawer shall be made of 6mm thick BWR plywood (Make: Greenply/Century/Archidply)

Removing old u/s handle from table bed side and S&F new CP handle 100 mm long (approved by GE) to table bedside. Rest all as specified, directed and shown on drawing.

Replacement of old u/s channel and S&F new telescopic channel of make Godrej/Hettich all as specified, directed and shown in drawing.

Removing old u/s side of table bed side and S&F new Side of suitable size made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa)) ISI marked confirming to IS-14587 Grade-I one side with approved shade and balancing white lamination on other side complete all as specified and directed

Removing old unservicable front leg of table bed side and S&F new front leg made of 18 mm (18 Gauge) MS sq pipe as per drawing complete all as specified and directed.

Removing old unservicable rear leg frame of table bed side and S&F new rear leg made of 18 mm (18 Gauge) MS sq pipe as per drawing complete all as specified and directed.

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M&L for preparation of old painted iron & steel surfaces of table bed side by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

CHARPOY WITH HARD TOP FD/MAP-II/01

Removing old u/s top and S&F plywood (Make: Greenply/Century/Archidply) top of suitable size 12mm thick BWR Grade ISI Marked confirming to IS-303 of Charpoy with Hard top made to shape & size as shown on drawings, complete all as specified and directed by GE.

M & L for welding to broken steel frame of Charpoy with Hard Top.

Removing of unserviceable shoe and S & F new hard rubber shoes as per drawing

M&L for preparation of old painted iron & steel surfaces of charpoy IP Hard top by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TABLE COMPUTER FD/E6/MAP/03,TP

Removing old u/s broken top and S&F new table Top of suitable size shall be made of 18 mm thick Prelaminated MDF Board exterior grade (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade approved by GE with 4 mm half round teak wood beading with fevicol duly polish with a coat of high glossy french polish complete and headless nails all round the edges all as specified and directed

Removing old u/s Shelves/bottom and S&F new shelves/bottom made of 18/19 mm thick prelaminated MDF Board (Make: Green Ply /Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I,Type-II of shade as approved by GE along with powder coated telescopic channel (make Godrej/hettich) as directed by Engr-in-Charge

Removing old u/s side/partion and S&F new Side/partion made of 18/19 mm thick prelaminated MDF Board (Make : Greenlam/Century/Action Tesa) ISI marked confirming to IS-14587 Grade-I,Type-II of shade as approved by GE.

Removing old u/s shoe and S&F new PVC adjustable shoe superior quality as approved by GE shall be provided.

M&L for preparation of old painted iron & steel surfaces of table computer by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint(1st grade quality) (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

DESK FOR SENIOR STANDARD 2 SEATER FD-166(M)

Removing old u/s top and S&F new top made out of plywood (Make: Greenply/Century/Archidply) top 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as directed by Engr-in-Charge and shown in drg.

Removing old u/s bottom and S&F new bottom made out of plywood (Make: Greenply/Century/Archidply) top 18/19mm thick BWR Grade ISI Marked confirming to IS-303 with 4mm dia 50mm long semi circular nut and bolts with washers drilling holes including seat and conduit frame all as directed by Engr-in-Charge and shown in drg.

Removing unserviceable sides and S & F new sides made out of plywood (Make: Greenply/Century/Archidply) sides 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as specified and shown in drg.

Removing unserviceable back and S & F new back made out of plywood (Make: Greenply/Century/Archidply) sides 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as specified and shown in drg.

M & L for welding to broken steel frame of Desk for Senior Standard 2 Seater complete all as specified and directed.

Removing unserviceable shoes and S & F new rubber shoe best quality all as directed by Engr-in Charge.

M&L for spray painting of repaired Desk for senior standard 2 seater completer on all surface applying two coats of synthetic enamel paint (Colour Shade as approved by GE) over a coat of red oxide primer on iron surface and white primer on wooden surfaces complete after preparation of surface by scraping complete removal of existing paint complete and removing of dust dirt etc from wooden/iron surface including denting as as required on iron surface all as specified and shown on drg and directed by GE/Engr-in-charge.

DESK FOR SECOND STANDARD 2 SEATER FD-167(M)

Removing old u/s top and S&F new top made out of plywood (Make: Greenply/Century/Archidply) top 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as directed by Engr-in-Charge and shown in drg.

Removing old u/s bottom and S&F new bottom made out of plywood (Make: Greenply/Century/Archidply) top 18/19mm thick BWR Grade ISI Marked confirming to IS-303 with 4mm dia 50mm long semi circular nut and bolts with washers drilling holes including seat and conduit frame all as directed by Engr-in-Charge and shown in drg.

Removing unserviceable sides and S & F new sides made out of plywood (Make: Greenply/Century/Archidply) sides 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as specified and shown in drg.

Removing unserviceable back and S & F new back made out of plywood (Make: Greenply/Century/Archidply) sides 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as specified and shown in drg.

M & L for welding to broken steel frame of Desk for Second Standard 2 Seater.

Removing unserviceable shoes and S & F new rubber shoe best quality all as directed by Engr-in Charge.

M&L for spray painting of repaired Desk for second standard 2 seater complete on all surfaces applying two coats of synthetic enamel paint (Colour Shade as approved by GE) over a coat of red oxide primer on iron surface and white primer on wooden surfaces complete after preparation of surface by scraping complete, removal of existing paint complete, and removing of dust, dirt etc from wooden/iron surface including denting as required on iron surface all as specified and shown on drg and directed by GE/Engr-in-charge.

DESK FOR KG STANDARD 2 SEATER FD-168(M)

Removing old u/s top and S&F new top made out of plywood (Make: Greenply/Century/Archidply) top 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as directed by Engr-in-Charge and shown in drg.

Removing old u/s bottom and S&F new bottom made out of plywood (Make: Greenply/Century/Archidply) top 18/19mm thick BWR Grade ISI Marked confirming to IS-303 with 4mm dia 50mm long semi circular nut and bolts with washers drilling holes including seat and conduit frame all as directed by Engr-in-Charge and shown in drg.

Removing unserviceable sides and S & F new sides made out of plywood (Make: Greenply/Century/Archidply) sides 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as specified and shown in drg.

Removing unserviceable back and S & F new back made out of plywood (Make: Greenply/Century/Archidply) sides 18/19mm thick BWR Grade ISI Marked confirming to IS-303 all as specified and shown in drg.

M & L for welding to broken steel frame of Desk for Second Standard 2 Seater.

Removing unserviceable shoes and S & F new rubber shoe best quality all as directed by Engr-in Charge.

M&L for spray painting of repaired Desk for second standard 2 seater complete on all surfaces applying two coats of synthetic enamel paint (Colour Shade as approved by GE) over a coat of red oxide primer on iron surface and white primer on wooden surfaces complete after preparation of surface by scraping complete, removal of existing paint complete, and removing of dust, dirt etc from wooden/iron surface including denting as required on iron surface all as specified and shown on drg and directed by GE/Engr-in-charge.

CHAIR FOR SENIOR/MIDDLE STANDARD FD-169(M)

Removing old u/s seat and S&F new seat made out of plywood (Make: Greenply/Century/Archidply) 12mm thick BWR Grade ISI Marked confirming to IS-303 with 4mm dia 50mm long semi circular nut and bolts with washers drilling holes including seat and conduit frame all as directed by Engr-in-Charge and shown in drg.

Removing old u/s back and S&F new back made out of plywood (Make: Greenply/Century/Archidply) 12mm thick BWR Grade ISI Marked confirming to IS-303 with 4mm dia 50mm long semi circular nut and bolts with washers drilling holes including seat and conduit frame all as directed by Engr-in-Charge and shown in drg. in drg.

Removing unserviceable shoes and S & F new rubber shoe best quality all as directed by Engr-in Charge.

M & L for welding to broken steel frame of Chair for Senior/Middle Standard.

M&L for spray painting of repaired Chair for senior/middle standard 2 seater complete on all surfaces by applying two coats of synthetic enamel paint (Colour Shade as approved by GE) over a coat of red oxide primer on iron surface and white primer on wooden surfaces complete after preparation of surface by scraping complete, removal of existing paint complete, and removing of dust, dirt etc from wooden/iron surface including denting as required on iron surface all as specified and shown on drg and directed by GE/Engr-in-charge.

CHAIR SCHOOL WITH HAND BOARD FD/E6/MAP/05

Removing old unserviceable seat/back of Chair and S&F one piece PVC Seat and back virgin quality as approved by GE all as specified and shown on drg.

Removing old unserviceable hand board of Chair and S&F new hand board top openable fixed on right hand side made of 18/19 mm thick Prelaminated MDF Board exterior grade (make: Greenply/century/action tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with standard PVC edging/wooden edging as specified and shown on drg.

M & L for welding to broken steel frame of Chair School with Hand Board.

M&L for preparation of old painted iron & steel surfaces of chair school with hand board by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel black paint over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

CHAIR VERANDAH FD/MAP-II/06, FD/MAP-II/15

M & L for Welding to broken steel frame of chair varandah by welding complete all as directed

S&F 4 mm thick PVC sheet for seat (Make:- Classic,Amko,cello) of Chair Verandah complete all as shown on drawing and as directed by the Eng - in - Charge.

S&F 4 mm thick PVC sheet for back (Make:- Classic,Amko,cello) of Chair Verandah complete all as shown on drawing and as directed by the Eng - in - Charge.

Taking down old unserviceable shoes and S & F rubber/PVC shoes to to leg of chair varandah complete all as specified and directed.

M&L for preparation of old painted iron & steel surfaces of chair verandah by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel white paint over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

RACK SHOE STEEL FD/E6/MAP/02(R)

Removing old u/s broken 3 mm dia MS rod (fitted along width direction) and S&F new 3 mm dia MS rod of length approx 300 mm all as shown on drawing. Rest all as specified and directed by Engr in Charge

Removing old u/s broken 3 mm dia MS rod (fitted along length direction) and S&F new 3 mm dia MS rod of length approx 700 mm all as shown on drawing. Rest all as specified and directed by Engr in Charge

M&L for preparation of old painted iron & steel surfaces of rack shoe steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel black paint over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

TRESTLE STORE ROOM STEEL FD-1043

M&L for preparation of old painted iron & steel surfaces of trestle store room steel by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel black paint over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge.

CHAIR PLASTIC WITH CUSHION TP

Removing old worn out fabric/tapestry including foam from the seat of the chair and S&F new seat including new foam and tapestry/fabric (as approved by GE) to match in original,all as specified and directed. The quoted rates must include the replacement of nut and bolts.

Removing old worn out fabric/tapestry including foam from the backrest of the chair and S&F new backrest including new foam and tapestry/fabric (as approved by GE) to match in original,all as specified and directed. The quoted rates must include the replacement of nut and bolts.

TABLE BED SIDE FD-276/FD-248

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and as shown in drg.

Replacement of old/us sides and S&F new sides made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and as shown in drg.

Replacement of old/us shelves and S&F new shelves made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and as shown in drg.

Replacement of old/us back ply and S&F new back ply made of 6mm thick plywood (Make: Greenply/Archidply/Century) of BWR Grade ISI Marked confirming to IS-303.

M&L for applying two or more coats of french polish on all exposed wooden surfaces of table bed side including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

SIDE BOARD/BIN LINEN MULTIPURPOSE

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and as shown in drg.

Replacement of old/us shutters and S&F new shutter made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE complete all as specified and as shown in drg.

Replacement of old/us sides and S&F new sides made of 18/19 mm thick Prelaminated MDF Board exterior grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE completed all as specified and as shown in drg.

Replacement of old/us drawers and S&F new drawers all as specified and shown in drg.

Replacement of old/us handles and S&F new Chromium Plated handles/knob (Approved by GE) of 100mm long fixed to shutters/drawers complete all as specified and as shown in drg.

Replacement of old/us shelves and S&F new shelves made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE.

Replacement of old/us back ply and S&F new back ply made of 6mm thick plywood (Make: Greenply/Archidply/Centuryply) of BWR Grade ISI Marked confirming to IS-303.

Replacement of old/us base support and S&F new Base support made of 1st Class TW all as specified and shown in drg.

M&L for applying two coats of french polish on all exposed surfaces of side board including cleaning and preaparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

HAT STAND WITH MIRROR

Replacement of old/us Mirror of Hat stand and S&F new mirror 5 mm thick as per drg. (Make: Modiguard/Atul/Saint Gobbain) complete all as specified and as directed.

Replacement of old/us pegs and S & F new brass pegs approved by GE of superior quality complete all as specified and as directed.

Replacement of old/us front sides ply and S&F new ply made of 4mm thick face plywood (Make: Greenply/Century /Archidply) of BWR Grade ISI Marked confirming to IS-303 complete all as specified and as directed..

Replacement of old/us back ply and S&F new ply made of 6mm thick plywood (Make: Greenply/Century /Archidply) of BWR Grade ISI Marked confirming to IS-303 complete all as specified and as directed..

M&L for applying two or more coats of french polish on all exposed surfaces of hat stand with mirror including cleaning and preparing the surface including a coat of wood filler on wooden surface as well as on teak face ply complete all as specified and as directed.

TABLE DRESSING LADIES WITH MIRROR

Replacement of old/us Mirror of Table dressing ladies and S&F new mirror 5 mm thick as per drg completed all as specified and shown in drg (Make: Modiguard/Atul/Saint Gobbain)

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm thick wooden beading with fevicol and headless nails all round the edges complete all as specified and shows in drg complete all as specified and as directed.

Replacement of old/us drawers and S&F new drawer complete all as specified and shown in drg.

Replacement of old/us knob/handle and S&F new CP handle 100 mm long complete all as specified and shown in drg.

Replacement of old/us sides and S&F new sides made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE.

Replacement of old/us Sliding glass and new Sliding glass shutters plain glass as specified and shown in drg

M&L for applying two or more coats of french polish on all exposed surfaces of table dressing ladies including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

TEAPOY WOODEN

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 6mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and as directed.

Replacement of old/us legs support and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails support and S&F new short rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us long rails support and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us bracket/corner and S&F bracket/corner made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of Teapoy wooden including cleaning and preparing the surface including a coat of wood filler on wooden surfaces.

TABLE PEG

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and shown in drg complete all as specified and as directed.

Replacement of old/us legs and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us long rails support and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails support and S&F new short rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us centre stiffener and S&F new centre stiffener made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of Peg Table including cleaning and preparing the surface including a coat of wood filler on wooden surfaces.

TABLE CENTRE

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm th wood beading with fevicol and headless nails all round the edges complete all as specified and shown in drg.

Replacement of old/us legs support and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us long rails support and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails support and S&F new short rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us bracket/corner and S&F new HW bracket/corner between leg and side rail all as specified and directed

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of table center including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

BED PLYWOOD

Replacement of old/us plywood top and S&F new plywood top made of 12 mm thick Plywood (Make: Greenply/Century/Archidply) of BWR Grade ISI Marked confirming to IS-303 complete all as specified and shown in drg.

Replacement of old/us long rails support and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails support and S&F new short rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us legs and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Head Board and S&F new Head Board made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Foot Board and S&F new Foot Board made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Stiffeners support and S&F new stiffeners made of 2nd class teak wood all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

Replacement of old/us Steel bent clamp for corner and S & F new Steel bent clamp for corner all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of Bed Plywood including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

SOFA SET 4/5 SEATER FD/MAP-II/02, FD-281

Replacement of old/us Side rail and S&F new Side rail made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us front or Back Plywood of 3 seater and S&F new front or Back Plywood made of 12mm thick plywood (Make: Greenply/Century /Archidply) of BWR Grade ISI Marked confirming to IS-303 complete all as specified and shown in drg.

Replacement of old/us front or Back Plywood of single seater and S&F new front or Back Plywood made of 12mm thick plywood (Make: Greenply/Century /Archidply) of BWR Grade ISI Marked confirming to IS-303 complete all as specified and shown in drg.

Replacement of old/us Stiffeners support and S&F new stiffeners made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Back strip of three seater and S&F new Back strip made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Back strip of single seater and S&F new Back strip made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

Replacement of unserviceable cushion for seat/back with new cushion of sofa set 4/5 Seater comprising single piece of seat/back each made of foam 40D of size 22”X21”X100/95mm Make: Sleep Well (Featherfoam)/ Kurlon(Gold) duly covered with tapestry cloth stitched with fine standard thread complete all as directed by GE and shown on drg no.FD/MAP/II/02. Note : Rate of tapestry cloth shall not be less than Rs 550/-per RM and colour and texture of Tapestry shall be approved by GE.

M&L for applying two or more coats of french polish on all exposed surfaces of sofa set 4 seater including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

M&L for applying two or more coats of french polish on all exposed surfaces of sofa set 5 seater including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

CHAIR DINING FD-279/228

Taking down old u/s Rear leg and M&L for new leg made out of 1st class teak wood all as specified in drg and directed by Engr-in-Charge.

Taking down old u/s Front Leg and M&L for New leg made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Side Rail and M&L for New Side Rail made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Front or Back Rail and M&L for New Front or Back Rail made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Bottom Stiffener and M&L for New Bottom Stiffener made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Back Strip and M&L for New back strip made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

M & L for removing old/worn out rubber shoes and S & F new Rubber/PVC shoe of superior quality with steel plated screws of suitable size complete all as directed by Eng - in - Charge

Removing old/unserviceable cane from chairs and M & L Re-canning of Chair Dining in Godrej pattern with oval shape 2 mm wide new white plastic cane and 4 mm wide at the edge including taking out old canning complete all as shown on drawing and as directed by the Eng - in - Charge.

M& L for Polishing two coats to new and old surfaces of Chair Dining after repair with french polish of approved quality including preparation of all surfaces complete all as specified and as directed.

CHAIR WRITING/CB OFFICE FD-202,250,280

Taking down old u/s Rear leg and M&L for new leg made out of 1st class teak wood all as speicified in drg and directed by Engr-in-Charge.

Taking down old u/s Front Leg and M&L for New leg made out of 1st class teak wood complete all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Side Rail and M&L for New Side Rail made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Front or Back Rail and M&L for New Front or Back Rail made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Bottom Stiffener and M&L for New Bottom Stiffener made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Taking down old u/s Back Strip and M&L for New back strip made out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

M & L for removing old/worn out shoes S & F new Rubber/PVC shoe of superior quality with steel plated screws of suitable size complete all as specified and as directed.

Taking down old u/s Arms Rest and M&L for New Arm rest out of 1st class teak wood all as specified in drg and as directed by Engr-in-Charge.

Removing old/unserviceable cane from chairs and M & L re-canning of Chair wrting in Godrej pattern with oval shape 2 mm wide new white plastic cane and 4 mm wide at the edge make as approved by GE including taking out old canning complete all as shown on drawing and as directed by the Eng - in - Charge.

M& L for Polishing two coats to new and old surfaces of Chair wrting after repair with french polish of approved quality including preparation of all surfaces complete all as specified and as directed.

CHAIR VERANDAH FD-359,256

M & L for Welding to broken steel frame of chair Verandah by welding complete all as directed

Taking down old unserviceable cane and Re- -canning of Chair Verandah with oval shape 4mm wide new plastic cane make as approved by GE. Rest all as shown on drawing and as directed by the Eng-In- Charge.

Taking down old unserviceable shoes and S & F rubber/PVC shoes to to leg of chair Verandah complete all as specified and directed.

M&L for spray painting two coats of synthetic enamel white paint complete ater prepartion of surface by scrapping and removing dust dirt etc including denting as required complete all as specified and as directed.

TABLE DINING 6/8 PERSONS

Replacement of old/us top 8 person and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and shown in drg.

Replacement of old/us top 6 person and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and shown in drg.

Replacement of old/us legs support and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us long rails support and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails support and S&F new short rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us bracket/corner and S&F bracket/corner made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of table dining 6/8 persons including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and directed.

TABLE DRESSING GENTS WITH MIRROR FD-230,379

Replacement of old/us Mirror of Table dressing gents and S & F new Mirror 5 mm thick as per drg. Complete all as specified and shown in drg ( Make: Modiguard/Atul/Saint Gobbain)

Replacement of old/us top and S & F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE complete all as specified and shown in drg complete all as specified and as directed

Replacement of old/us drawers and S&F new drawers all as specified and shown in drg.

Replacement of old/us knobs/handles and S&F new CP handles 100 mm long all as specified and shown in drg.

Replacement of old/us Bottom and S&F new Bottom made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as apprvd by GE.

Replacement of old/us sides and S&F new sides made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as appvd by GE.

M&L for applying two or more coats of french polish on all exposed surfaces of table dressing gents including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

TABLE DINING 4 PERSONS (1200x900)

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/ Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and shown in drg.

Replacement of old/us legs support and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us long rails support and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails support and S&F new short rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us bracket/corner and S&F bracket/corner made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of table dining 4 persons including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and directed.

TABLE WRITING

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm thick wood beading with fevicol and headless nails all round the edges complete all as specified and shown in drg.

Replacement of old/us legs and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us long rails and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails and S&F new short rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us back ply and S&F new ply made of 6mm thick plywood (Make: Greenply/Century /Archidply) of BWR Grade ISI Marked confirming to IS-303.

Replacement of old/us Stiffeners support and S&F new stiffeners made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us drawers and S&F new drawers all as specified and shown in drg.

Replacement of old/us shutters and S&F new shutters all as specified and shown in drg.

Replacement of old/us handles/knobs and S&F new CP steel handle 100 mm long all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of Table writing including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

TABLE 3'x2' WOODEN

Replacement of old/us top and S&F new top made of 18/19 mm thick Prelaminated MDF Board exterior Grade (Make: Greenply/Centuryply/Action Tesa) ISI marked confirming to IS-14587 Grade-I of shade as approved by GE with 4 mm th wooden beading with fevicol and headless nails all round the edges complete all as specified and shown in drg.

Replacement of old/us legs support and S&F new leg made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us long rails support and S&F new long rails made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us short rails support and S&F new short rails made of 1st class teak wood all as specified and shown in drg

Replacement of old/us drawers and S&F new drawers all as specified and shown in drg.

Replacement of old/us bracket/corner and S&F bracket/corner made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

M&L for applying two or more coats of french polish on all exposed surfaces of table 3'x2 wooden including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

CHAIR DINING CUSHIONED FD/E6/MAP/10(R) , TP

Replacement of old/us Rear legs and S & F new Rear legs made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Front legs and S&F new Front legs made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Side rail and S&F new Side rail made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us front or Back rail and S&F new front or Back rail made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us Bottom Stiffeners support and S&F new Bottom stiffeners made of 2nd class teak wood all as specified and shown in drg.

Replacement of old/us Back strip and S&F new Back strip made of 1st class teak wood all as specified and shown in drg.

Replacement of old/us bracket/corner and S&F new wooden corner/bracket to provide support to legs

Replacement of old/us PVC shoe and S&F new PVC shoe superior quality all as specified and shown in drg.

Replacement of old/us Seat and S&F new Seat made made of foam 40D Make: Sleep Well( Featherfoam), Kurlon(Gold) duly covered with tapestry cloth with fixed over 12 mm Plywood (Make: Greenply/Centuryply /Archidply) of BWR Grade ISI Marked confirming to IS-303 complete all as specified and shown in drg complete all as specified and directed. Note : Rate of tapestry cloth shall not be less than Rs 550/-per RM and colour and texture of Tapestry shall be approved by GE.

M&L for applying two or more coats of french polish on all exposed surfaces of chair dining(MAP) including cleaning and preparing the surface including a coat of wood filler on wooden surfaces complete all as specified and as directed.

Repair & Removing following old wornout/broken/unservicable parts of hospital furniture and S&F new parts best quality (approved by GE) to match the original in all respect and fixing in position properly :

Adjustment of drawers of cabinet filing

Channel of Cabinet filing

Cloth of Screen movable 3 fold

Castor/wheel of table bedside steel

Complete leathrerite seat & back assembly of chair invalid wheeling

Adjustment of wheel of Chair invalid wheeling for smooth running

M&L for preparation of old painted metal surfaces of following hospital furniture by scraping & rubbing down with sand paper, removing dents & scratches, if any filling the same with paste fillet and spray painting two coats of synthetic enamel paint (Colour shade as approved by GE ) over a coat of red oxide primer complete after preparation of surface all as specified and directed by Engr-in Charge

Bed Stead Iron/fowler (Drg : TP)

Cabinet Filing (Drg : TP)

Couch Examination (Drg : TP)

Screen Movable (Drg : TP)

Table Bedside Steel (Drg : TP,HFD-2005)

NOTE : (Applicable for all items):- (i) The bidders/contractors are advised to read relevant Contract drawings and Particular specifications, Key specifications, Special conditions and General conditions of Contracts before entry/quoting the rates. (ii) The items are to be manufactured as per relevant drawings and specifications and supplied to the Department.

M/SDoon furnishers (BID ID -3409276)

VARAROHA BUILDERS (BID ID -3393604)

Raghav supplier & contractor (BID ID -3397488)

avtarsinghchaddha (BID ID -3401787)