Construction of office building of Thunag Division under Jal Shakti Circle Sunder Nagar Distt Mandi HP

Amount

Cutting in earth work and disposal of excavated earth in all kinds of soil in pick work 70%, Jumper work 30% complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Excavation in foundation trenches etc. in earth work upto all depth in all kinds of soil such as pick work jumper work blasting work chiselling of soft /hard rocks where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade excavated soil in 15cm layers when required into plinth side of foundation including consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed in all leads and lifts.

Providing and laying cement concrete 1:4:8(1cement:4 sand: 8 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs and removal of the same for in situ- reinforcement concrete and plain concrete work, in all leads & lifts in:-

Foundation footing and bases of columns and mass concrete including plinth beams and columns upto plinth including carriage of materials within all leads, lifts and other incidentals.

Beams, cantilevers girders and lintels, side of soffits of beams, beam haunchings cantilevers, bressumrers and lintels not exceeding 1.00 mtr. In depth in all height in floor.

Flat surfaces such as soffits of suspended floors,roofs, landings and the like.Floors etcupto 200mm in thickness including carriage of materials within all leadsm lifts and other incidentals.`

Columns, pillar posts and struts, square rectangular polygonal in plan

Stair cases with slopping or stepped soffits excluding landing.

Vertical surface such as walls(any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like

Edges of slabs and breaks in floors and walls under 20cm wide.

Randum rubble masonary polygonal rubble masonary (uncoursed brought to courses in walls with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1cement: 6 sand: 12 graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1cement: 6 sand) in breast wall sand retaining walls in all leads and lifts.

Providing and laying cement concrete 1:5:10 (1 cement: 5 sand: 10 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work in foundation and plinth complete in all respect and as per direction and to the entire satisfaction of the Engineer-in-charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per direction of the Engineer-in-charge.

Stone soling/boulder filling dry hand packed in under floor as per the direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidental.

Providing and laying damp proof course 38 mm thick with cement concrete 1:2:4 (1 cement :2 sand :4 stone aggregate 12.5mm nominal size) and curing complete in all respect in all leads and lifts.

Providing and laying cement concrete 1:2:4 (1cement:2sand : 4graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and re-inforcement for reinforced concrete work in

Foundatioins, footings bases of columns and the like and mass concrete

Suspended floors roofs, landings and shelves and their supports, balionies, beams, girders bressumers and cantilevers upto floor two level in all leads and lifts.

Columns, pillars posts and struts upto floor two level.

walls any thickness but not less than 0.1 mtrs. thickness attached pillasters , plinths and string courses etc.from top of foundation level upto floor two level in all leads and lifts .

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing Mild Steel/Tor steel reinforcement for reinforced cement concrete work including bending binding and placing in position complete including the cost of binding wire in all leads and lifts.

Providing and laying 20 cm thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6 (1cement :76 sand) and concrete backing with cement concrete 1:3:6 ( 1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) on inner face of walls including centring, shuttering and

Brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 ( 1 cement :4 sand) second class bricks in all leads and lifts.

Super structure above plinth level upto floor two level (Second Class Bricks)

Super structure above floor two level

Half brick masonry in common burnt clay building bricks in :- Cement motar 1:4 (1 cement :4 sand) Second class bricks.

Providing wood work in frames of doors, windows, clerestory, windows and other frames wrought framed and fixed in position, 2nd class deodar wood.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm 1:3:6 ( 1cement: 3 sand :6 graded stone aggregate 20mm nominal size complete in all respect in all leads and lifts.

Steel work welded in built up sections, trusses andframed work including cutting, hoisting fixing in position and applying a priming coat of red lead paint complete in all respect in all leads and lifts in:-

In trusses and trussed purlins in buildings.

In gratings fraqmed guard bars, ladders, railing, brackets and similar works.

Providing and fixing 75mmx60mm rounded hand rails in straight length complete in all respect in all leads and lifts (i) 2nd class Indian teak wood.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted Iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per direction of the Engineer-in-charge.

Providing and fixing ridges or hips 60cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating+ back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted Iron J or L hooks, bolts and nuts 6mm dia & prepainted GI limpet and bitumen washers complete with all accessories as required as per direction of the Engineer-in-charge.

Providing and fixing M.S. B.P. sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of the Engineer-in-charge (Base members of steel work shall be measured and paid separately)

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5kg/Sqm including filling the joints with approved adhesive complete 100mm dia pipe

Providing and fixing wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete PVC Plain Bend 100mm dia

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. flats, square or round bars with round headed bolts and nuts or by screws Plain grill.

6mm cement plaster to ceiling (a) in cement mortar 1:3 (1cement :3 sand) complete in all respect in all leads and lifts.

15mm cement plaster in single coat on rough side of brick/ concrete/ stone walls for interior plastering upto floor two levels including arrises internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) in all leads and lifts.

15mm cement plaster in single coat on fair side of brick/ concrete/ stone walls for interior plastering upto floor two levels including arrises internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) in all leads and lifts.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows including black enamelled iron butt hinges with necessary screws etc complete as directed in all leads and lifts and to the entire satisfaction of Engineer-in-charge. 40mm thick 2nd class deodar wood.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56mm for doors, windows and clerestorey windows including black enamelled iron hinges with necessary screws etc. complete as directed in all leads and lifts and to the entire satisfaction of Engineer-in-charge. (a) 40mm thick 2nd class deodar wood.

Providing and fixing 12mm thick 150mm wide palment with 25mm dia wooden curtain rods and brackets including fixing 25x3mm MS flat at 10cm long and plugs etc. coomplete

Providing and fixing anodized aluminium sliding door bolts with nuts and nuts screw etc. complete in all leads and lifts.

Providing and fixing Aluminium tower bolts (barrel type) with screws etc. complete in all leads and lifts (i) 250x10mm

Providing and fixing Aluminium handles with necessary screws etc. complete in all leads and lifts (i) 125mm

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete.

Providing and fixing bright finished hard drawn hooks and eyes 200mm dia

Providing and fixing oxidized M.S. single acting spring hinges with necessary screws etc. complete (i) 150mm

Providing and fixing 10mm thick anti skid water proof stain and impact resistent heavy duty vetrified tiles Nitco or equivalent 600x600x10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

Providing and fixing full body vetrified tile 600x600mm with V.C . shield technology Nitco or equivalvent manufactured of approved shade and colour in skirting riser of steps and dados laid over 12mm thick cement mortar 1:3 ( 1cement : 3 sand) joined with cement slurry mixed with pigment to match the shade of tiles as required complete as per direction of the Engineer-in-charge.

Providing and fixing 8mm digital ceramic tile of digital series size 300x600mm of Somany/Kajaria/Nitco or its equivalent of approved shade and colour in Skirting risers of steps and dados on 8mm thick cement mortar 1:3 ( 1cement : 3sand) laid over and jointed with neat cement slurry finished with flush pointing with white cement mixed with pigment of required shade to match the shade of tiles complete as per direction of the Engineer-in-charge

Providing and laying granite stone in flooring 20mm ( average) thickness base of cement mortor 1:3(1cement:3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete 20mm thick

Providing and fixing 19mm (nineteen millimeter) thick termite resistant water proof commercial board box including shelves and shutter, the back side of cupboard/cabinet of 8mm (eight millimeter) thick ply and cut portion of shelves shall be finished with 6mm (six millimeter) hard board edging. The cut portion of shutter from all the sides shall be finished with 12mm thick hard wood edging the shutter from out side shall be finished with 1mm thick laminated or approved shade including piano hinges and magnetic catcher with all accessories as per detail drawings.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Applying one coat of Acrylic primer (Spectrum or equivalent of superior quality) on new concrete/masonry/plastered surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar dropings and other foreign matters, sand papering the surface smooth complete.

Distempering ( two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign mater and also including preparing the surface even and sand papered smooth, priming coat with distemper Primer for distempering with oil bound distemper on ceiling and/or sloping roofs complete.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface.

Varnishing two coats( excluding priming coat) on new wood and wood based surfaces, under coating, with flatting varnish and finishing coat with varnish to give an even surface including cleaning the surfaces of all dirt, dust and sand papering so as to produce a smooth, dry and matt surface.

Polishing two coats wih French polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil, grease,dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead, Red-Oxide/Zincoxide chrome.

Painting two coats ( excluding priming coat) on new steel and other metal surfaces either enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters (i) Enamel paint other than white

(ii) Enamel paint white

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease , dirt and other foreign matters, sand papering and knotting ready mixed paint brushing wood primer pink in all leads and lifts.

Painting two coats ( excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including clearing of all dirt dust and other foreign matter, sand papering & stoping with enamel paint other than white in all leads and lifts.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregate 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground complete

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement : 3 sand :6 graded stone aggregate 20mm nominal size complete.

Constructing course rubble hammer dressed 'U' shape open surface drain with side wall 15x22cm in cement mortar 1:6 (1cement :6 sand) and inside plastering with cement plaster 1:3 (1cement : 3 sand) including earth work and laying 10cm cement concrete in 1:5:10 ( 1cement : 5 sand : 10 graded stone aggregate) of 40mm nominal size and 7.5cm cement concrete 1:2:4 ( 1 cement : 2 sand : 4 graded stone aggregate of 20mm nominal size) and finished with a floating coat of neat cement complete as per standard design.

Providing and fixing 15cm wide 45cm overall semicirular plain GI sheet gutter with iron brackets 40x3mm size bolts, nuts and washers etc. including making necessary connections with rain water pipe complete as per design 0.80mm thick sheet.

Excavation in drain and channels etc. in all kinds of soil such as pick work, jumper work, ballast work soft or hard blasting saturated soil or other mixed soil including lip cutting after dressing and compaction of sides and beds & disposing of excavated materials in all leads and lifts disposed material to be levelled and neatly dressed including compaction as per instruction of the Engineer-in-charge.

Providing and laying 20mm (twentty millimeter) nominal bore in trenches, galvanised mild steel tubes (Medium grade) tube fittings (earth work in trenches to be measured and paid separately) as per direction of the Engineer-in-charge.

Providing and fixing to wall ceiling and floor galvanized mild steel tube (Medium grade) tube fittings and clamps including making good the wall ceiling and floors in all leads and lifts in:-

15mm (fifteen millimeter) nominal bore.

20mm (twenty millimeter) nominal bore.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm (twenty millimeter) to 40mm (forty millimeter) nominal bore by providing and fixing including cutting and threading the pipes complete 25mm dia (twenty five millimeter) complete.

Providing and fixing P.V.C. storage tank complete 40mm nominal bore galvanised mild steel scour filling 25mm nominal bore galvanised mild steel over flow tube with fitting and mosquito proof approved municipal design 15mm nominal bore ball valve and mosquito proof coupling PVC locking arrangement including providing pads of size as required for inlet and outlet tubes including hoisting upto all height above ground level 1000 liters net capacity

Providing and fixing PVC 110mm (one hundred ten millimeter) size "P" or "S" trap for water closet (squatting pan) including jointing the trap with the pan and soil pipe with approved adhesive as per direction of the Engineer-in-charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor etc. complete 110x90mm (one hundred ten x ninety millimeter) as per direction of the Engineer-in-charge.

Providing and fixing high pressure PVC spigot and socket vest and ventilating pipes ISI marked including fixing with approved adhesive etc. complete as per direction of the Engineer-in-charge (a) 110mm (one hundred ten) dia

150mm (one hundred fifty ) dia

Providing and fixing 110mm (one hundred ten millimeter) dia PVC single equal branch with over cess door, ISI marked intersection washer 3mm (three millimeter) thick bolts and nuts complete including fixing with approved adhesive etc. complete as per direction of the Engineer-in-charge.

Providing and fixing 110mm (one hundred ten millimeter) dia PVC door bend with oval access door, ISI marked intersection washer 3mm (three millimeter) thick bolts and nuts complete including fixing with approved adhesive etc. complete as per direction of the Engineer-in-charge.

Providing and fixing 110mm (one hundred ten millimeter) dia, PVC collar ISI marked including fixing with approved adhesive etc. complete as per direction of the Engineer-in-charge

Providing and fixing 110mm (one hundred ten millimter) dia, PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of the Engineer-in-charge.

Providing and fixing 110mm (one hundred ten millimter) dia, PVC clamp ISI marked approved design with steel screws and rowel plugs etc. complete as per direction of the Engineer-in-charge.

Providing and fixing vitreous china water closet squatting pan (Indian type W.C. pan) size 580mm (earth work, bed concrete footrest and trap to be measured and paid for separately) Orissa pattern as per direction of the Engineer-in-charge.

Providing and fixing vitreous china down water closed (European type W.C. pan) with integral "P" or "S" trap including the trap with soil pipe in cement mortar 1:1 ( seat and cover to be measured and paid for separately) Anglo Indian (Universal closet) as per direction of the Engineer-in-charge.

Providing and fixing white glazed fire clay stall urinal with automatic C.I. flushing cistern of approved made with fittings R.S. or C.I. brackets standard size, C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) C.I. trap with outlet grating and coupling in C.P. brass including painting of cistern and fittings, cutting and making good the walls and floors where required.

Providing and fixing C.P. brass flush pipe/spreader for urinal with fitting such as union clamp etc. (all in C.P. brass) including cutting holes and making good the same 32mm (thirty two millimeter) dia, nominal bore as per direction of the Engineer-in-charge.

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting (a) Flat back (i) 630mmx450mm

Providing and fixing vitreous china pedestal for wash basin complete recessed at the back for the reception of pipe and fittings as per direction of the Engineer-in-charge.

Providing and fixing 32mm (thirty two millimeter) dia, C.P. brass waste for wash basin and sink for approved brand and manufacture as per direction of the Engineer-in-charge.

Providing and fixing M.I. union for wash basin or sink 32mm (thirty two millimeter) dia, size as per direction of the Engineer-in-charge.

Providing and fixing 32mm (thirty two millimeter) dia, C.P. brass bottle trap for wash basin and sink as per direction of the Engineer-in-charge.

Providing and fixing 600mmx450mm beveled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers

Providing and fixing C.P. brass towel rail complete C.P. brass brackets fixed to wooden plugs with C.P. brass 750mmx20mm

Providing and fixing 600mmx120mm glass shelf with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws

Providing and fixing toilet paper holder C.P. brass as per direction of the Engineer-in-charge.

Providing and fixing chromium plated brass soap dish with C.P. brackets fixed to wooden cleats with C.P. brass screws

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. bracket painted white including cutting holes and making good the same but excluding fitting 610x510mm with bowl depth 200mm

Providing and fixing division plate for urinals 600x330mm (six hundred x three hundred thirty millimeter) size vitreous China as per direction of the Engineer-in-charge.

Providing and fixing plastic seat (solid/hallow type) and cover for wash down water closet with C.P. brass hinges and rubber buffers: Solid type (a) White plastic seat and cover.

Providing and fixing C.P. jet with flexible C.P. connection pipe as per direction of the Engineer-in-charge.

Providing and fixing 15mm (fifteen millimeter) dia, C.P. brass bib tap with capstan head as per direction of the Engineer-in-charge.

Providing and fixing 15mm (fifteen millimeter) dia, C.P. brass pillar tap with capstan head as per direction of the Engineer-in-charge.

Providing and fixing 15mm (fifteen millimeter) dia, C.P. brass top cock with capstan head as per direction of the Engineer-in-charge.

Providing and fixing 15mm (fifteen millimeter) dia, C.P. brass angle valve without nut and pipe as per direction of the Engineer-in-charge.

Providing and fixing Mixer for kitchen sink with casted swingling spout at top

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap.

Providing and fixing PVC connection pipe with brass unions 300x450x600mm (three hundred x four hundred fifty x six hundred millimeter) length 15mm (fifteen millimeter) nominal size as per direction of the Engineer-in-charge.

Providing and fixing brass full way valve with wheel as per direction of the Engineer-in-charge.

15mm (fifteen millimeter) nominal bore.

20mm (twenty millimeter) nominal bore.

Providing and fixing brass ball valve (Horizontal plunger type) high pressure with polythene plastic float

15mm (fifteen millimeter) nominal bore.

20mm (twenty millimeter) nominal bore.

Providing and fixing PTMT coloured/white automatic flushing cistern with a pair of PVC/CI or MS bracket complete with fittings including PVC symphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (over flow pipe to be measured and paid for separately) (i) 10 liters net capacity

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 liters capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and overflow pipe, 40mm dia, C.P. flush bend including cutting holes and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for separately)

Providing and fixing PTMT waste coupling of approved quality and colour as per direction of the Engineer-in-charge.

Providing and fixing PTMT urinal waste coupling of approved quality and colour as per direction of the Engineer-in-charge.

Constructing manhole with RCC top slab in !:2:4 ( 1cement : 2sand : 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 (1 cement :4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement :3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement :2 sand :4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing complete.

Inside size 800mmx800mm and 1.00 mtr, deep including CI cover with frame ( light duty single (seal) pattern I) 450mmx610mm internal dimensions total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg and weight of frame 15 kg).

With 300mm thick walls of squared rubble masonary coursed with hard stone of approved quality in cement mortar 1:3 (1cement :3 sand) .

Wiring for light point/fan point/exhaust fan/call bell point with 1.5Sq.mm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core ( flexible) copper conductor cable in surface/recessed steel conduit and earthing the light point with 1.5Sq mm HRFRLS/PVC insulated single core copper conductor cable as required Group-C complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Wiring for light plug with 2x1.5Sq.mm PVC insulated heat resistant flame retardant ( HRFR)and low smoke single core ( flexible) copper conductor cable in surface/ recessed PVC conduit along with 1 No.1.5Sq.mm HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Wiring for power plug with 2x4Sq.mm PVC insulated heat resistant flame retardant ( HRFR) and low smoke single core ( flexible) copper conductor cable in surface/ recessed PVC conduit along with 1 No. 4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Supplying & fixing metal box of following sizes ( nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required complete in all respect

200mmx150mmx75mm deep

180mmx100mmx60mm deep

Providing and fixing 5 pin 5/ 6 Amps socket outlet porcelain base/piano type.

Providingm and fixing 6 pin 15 Amps socket outlet porcelain base/ piano type

Supplying and fixing following rating Piano type swtich/socket on the existing switch board/cover including connections etc . as required.

S.P. 5/6 Amp. One way switch, piano type

Bell push, piano type

S.P. 15/16 Amps of one way switch, porcelain base/piano type

Providing, Installation, testing and commissioning of ceiling fan 1200mm sweep, (Category-A) with regulator, including wiring the down rods of standard length ( upto 30cm) with 16/0.20mm twin twisted flexible, cotton braided, copper cable, including, providing and fixing phenolic laminated sheet cover on the fan box and earthing etc as required complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and installation of stationary storage type Electric water heater ( Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of nonreturn valve, dead weight safety valve 2Nos. C.P connection rods 18" long, making good the damages, electrical connections,safety valve connections,testing and commissioning etc. as required complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

25 litre capacity water heater Cat.B.

6 Litres capacity water heater ( instant geyser).Cat.B.

Providing and installation of exhaust fan of following sizes in the existing opening including making the hole to suit the size of the above fan, making good the damages connections,testing and commissioning etc as required:- Exhaust fan, Heavy duty 300mm sweep complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing, installation, testing and commissioning of pre-wired, fluorescent light fitting/compact fluorescent fitting of all types. Complete with all accessories and tubes etc directly on ceiling/ wall including connections with 16/0.20mm twin twisted flexible, cotton braided, copper cable and earthing etc as required complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Supplying and fixing of bulk head fitting of all sizes and shapes, containing one No. thread type CFL lamp holder(s), complete with all accessories but excluding CFL lamp including making connections testing etc. as required complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Bulk head fitting, CFL type ( Category-A)

Supplying and fixing fancy wall bracket containing threaded type CFL lamp holder (s) of all sizes and shapes, complete with all accessories but excluding CFL lamp and including making connections testing etc. as required:-

Fixed type wall bracket 150mm dia single lamp ( Category-A)

Mirror light 460mm, single lamp ( category-A)

Supplying and fixing bakelite batten/angle holder including connections etc as required complete.

Supplying and fixing Ding-Dong/Electronic musical bell, suitable for DC/AC single phase,230volts complete as required complete.

Supplying and fixing of 20mm diameter PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required complete.

Supplying and fixing following rating double pole ( single phase & neutral) 240volts, residual current circuit breaker ( RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections,testing and commissioning etc as required complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge:-

25Amps Cat-A.

Earthing with GI earth pipe 4.5mtr long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc ( but without charcoal or coke and salt) complete as required.

Extra for using salt and charcoal for pipe earth electrode complete as required complete in all respect.

Supplying and laying 6 SWG GI wire at 0.50mtr below ground level for earth electrode conductor including soldering etc as required complete.

Wiring for circuit/ Sub-main with following size PVC insulated heat resistant flame retardant ( HRFR) and low smoke single core ( flexible) copper conductor cable in surface/ recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete:-

2x10 Sq.mm

2x6.0 Sq.mm

2x4.0 Sq.mm

Supplying and fixing of single door 8 way single pole and neutral sheet steel MCB distribution board, 240 volts on surface/ recess complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar detachable gland plate, blanking plate, cable indentification labels inter connections, phosphatized and power painted, including earthing etc as required complete.

sanjeev govt cont

Tek Singh Raghav

gagan ohri