Recast estimate for the Fabrication and erection of one No Lock

Amount

Formation of sand bund for the fabrication and erection Lock Gate ,bailing out of water, as per the direction of departmental officer at site

od32372/2020_2021/MH : Forming and removal of Straight earth bund across the river of bund size 3.2m bottom width and 1.7m top width and 3.00m height using two rows of sand filled bags (60 cm) on either sides stacking in line and row and filled in between with good quality earth, driving casuarina poles driven 60cm centre to centre on outer sides including all cost and conveyance of materials, compaction of earth and maintaining the bund till the completion of the work and dismantling and cleared off after completion

60.2.3 : Bailing out water using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete

Supply, Fabrication, Painting, Erection, and commissioning of 1 No. Cross Regulator Shutter of Size 5.25m x 2 m with structural steel confirming to IS-2062 Gr.B etc. complete as per approved specifications, drawings

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.110 : Fabrication and supply of Structural steel wheel gate and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

od32374/2020_2021/MH : Erection of the gates safely in the grooves , assembling and aligning including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

85.109 : Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track,Seal seat etc as per approved specifications, drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

Supplying and fixing in correct position with Flat type rubber seal at bottom, bulb nose rubber seal at vertical upstream sides of the one no.Regulator shutter at SM Lock, complete as per approved specification and drawing

85.116 : Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.118 : Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

Supplying and fixing cast steel thrust roller assembly having 200 mm dia. 80 mm tread width, SS(304) shaft and 22312E self aligning spherical roller bearing and accessories as per approved specifications and drawing

od32373/2020_2021/MH : Supplying and fixing cast steel thrust roller assembly having 200mm Dia, 80mm tread width, SS(304) shaft and 22312E self aligning spherical roller bearing and accessories as per approved specifications and drawings including cost of all materials, machineries, labour , all lift and lead, incidental and conveyance charges etc complete

Supply, Fabrication, Painting, Erection, Commissioning of Hoist bridge with structural steel, Aluminium Chqd. plate for platform, hoist unit cover, hand rails, ladder,support structure, etc complete as per approved spec. and drawings

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.104 : Supply of Al checquered plates including cost of conveyance charges

od32375/2020_2021/MH : Supply of 32 NB Pipe

od32376/2020_2021/MH : supply of bolt and nut upto 300 mm length

od32377/2020_2021/MH : supply of M.S.bolt and nut above 300 mm length

85.106 : Supply of MS flats including cost of conveyance charges

85.124 : Fabrication and supply of Hoisting bridge unit in structural steel confirming to IS2062Gr including ladder, covers for hoisting unit etc as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, incidental and handling charges for fixing handrails and allied works etc complete but excluding material already supplied and weight of pipes for hand rails etc

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od32378/2020_2021/MH : Erection of the hoisting bridge unit including handrails , ladder and platform etc. in correct alignment and anchoring it ; setting and aligning the covers of the hoisting unit etc complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

od32379/2020_2021/MH : Supply of Twisted steel/ deformed TMT bars confirming to Fe-500D including cost of conveyance charges for the reinforcement for the concrete works

od32426/2020_2021/MH : Supply of S.S.Bolts and nuts

Supplying & stacking of 7.5 Tonne Capacity rope drum hoisting unit having a speed of 74mm/min including manual operating mechanism and brake drum unit, dog clutch etc

od32369/2020_2021/MH : Supply ing and stacking of 7.5 Tonne capacity rope drum hoisting unit having 3 m lift at a hoisting speed of about 74mm/min(+/-10%) through pulley arrangements with two numbers of falls on either side with 16mm tested galvanized wire rope 6/36 construction, fibre core having breaking capacity 18081Kg and driven by manual operating system driven through self locking worm reducer and open gear reduction unit excluding the cost of line shaft but including 2 nos. of plummer blocks with bearings for line shaft supported at proper intervals and including cost of thruster brake assembly manual operating systems, and other safety equipments as per drawings specifications and statutory requirements etc complete but excluding cost of wire rope.

Cost of supplying and stacking including conveyance charge of 16 mm tested steel wire rope 6/36 construction, fiber core,minimum breaking strength 18.081 T. confirming to IS2266-1989

od32368/2020_2021/MH : Supply of 16mm dia Steel wire Rope 6/36 fibre core confirming to IS: 2262 having a break load of 18081Kg with the grade of 1770N/mm2

Conveying and erecting in position the already supplied rope drum hoisting units on the hoisting bridge and correcting the alignment as far as possible manually

od32371/2020_2021/MH : Conveying and erecting in position the already supplied rope drum hoisting units 7.5T capacity on the hoisting bridge and correcting the alignment as far as possible manually as per the direction of departmental officer at site including cost of all labour, machinery, lead and lift and all incidental and conveyance charges etc complete

Conveying & Fixing wire rope already supplied to the new gates and Hoisting unit safely and in correct alignment and taking ssatisfactory trail run of the whole system by both manual operating system and driven by the primemover already provided

85.135 : Conveying and Fixing wire rope already supplied to the new gates and Hoisting unit safely and conducting Trial run

Reinforced cement concrete work in the grooves, sill beam and reinforcement with 1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

od32425/2020_2021/MH : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

Providing and laying in position specified grade of reinforced cement concrete,includes the steel re inforrced concrete for footing and foundation work for columns base plates for supporting the hoist structure .

5.1.3 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Site clearance by removing of silt, debris and organic wastes from the Proposed site using Pontoon JCB, the labour for Loading,unloading,disposal and clearing the site etc..

od32414/2020_2021/MH : Hire charge of Pontoon JCB (Grab Dredger) including fuel charge,operator, etc. for the removal silt, debris and organic wastes from the working site

od32424/2020_2021/MH : Loading the excavated wastages and debrises, removal and disposal of these from the site and which have to unloaded to the allotted place within a distance of 5km radius in the tractor-trolley and the Labour charges for loading and clearing the site

Bidder Name

RAJEEV K