ALTERATION CUM SPECIAL REPAIRS TO CERTAIN OFFRS JCOS ORS MD ACCN AT GUNGHORA BIRPUR ANARWALA AT DEHRADUN

Amount

Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete as directed and specified.

Demolition of Stone slabs and tiles of any description or thickness in floors, and walls etc.Laid, bedded and pointed in any mortar complete as directed and specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.complete as directed and specified.

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of brick work in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling timber scantling 40 sq cm and over in section , in any position for unframed work complete all as specified and directed by Engr-in-Charge

Dismantling timber scantling 40 sq cm and over in section , in any position for framed work complete all as specified and directed by Engr-in-Charge

Dismantling Mild Steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge

Dismantling of asbestos cement sheets of any description (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed by Engr-in-Charge

Dismantling of steel/galvalume sheets of any description (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed by Engr-in-Charge

Dismantling wall and ceiling board,of any description complete all as specified and directed by Engr-in-Charge

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down shutter of any description exc. 1.0 Sqm but n.exc 2.0 Sqm each and removing from site complete all as specified and directed.

Taking down shutter of any description n.exc 1.00 Sqm each and removing from site complete all as specified and directed.

Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections complete all as specified and directed.

Dismantling of water tanks capacity exc 500 ltrs and n.exc 1000 ltrs complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair face of brick work surfaces in CM 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded crushed stone aggregate as in floors, to receive surface of tile complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 20 mm thick for kota stone , in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 300 X 300 X 7 to 8 mm thick on floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. MAKE Kajaria, Johnson, Somany, Orient Bell

M&L for non-skid coloured ceramic tiles 8 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. MAKE Kajaria, Johnson, Somany, Orient Bell

M&L for non-skid coloured ceramic tiles 8 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in Skiting, riser etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed. MAKE Kajaria, Johnson, Somany, Orient Bell

M&L Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed. MAKE Kajaria, Johnson, Somany, Orient Bell

M&L for vitrified ceramic tiles light shade coloured 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. MAKE Kajaria, Johnson, Somany, Orient Bell

M&L for vitrified ceramic light shade coloured tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , on vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed. MAKE Kajaria, Johnson, Somany, Orient Bell

M & L for 20-25mm thick machine cut kota stone slab as in flooring over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding complete all as specified and directed.

M & L for 14-16 mm thick machine cut pre polished kota stone tiles as in skirting over and including 15 mm thick rendering in CM 1:4 complete all as specified and directed.

M & L 18 to 20 mm thick granite (Zed Black) (as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /plateform counter top WHB in cluding cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed in 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

M& L for 75 mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection joint filled with bitumen and sand mixture complete all as specified and directed.

M&L cement concrete 1:5:10 type E-2 using 40 mm graded stone aggregates as in sunken portion etc complete all as specified and as directed

S&F for 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M&L for brick work with old size bricks sub class B, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

All as per S.No 36 above but except bricks.

M&L for 15mm thick rendering in cement mortar 1:6 on fair faces / other than fair faces of brick masonary finished even and fair without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 with mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. Note:- Water Proofing compound shall be measured and paid seprately.

M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and directed.

Taking down existing un-serviceable water proofing treatment from roof slab and cleaning the roof slab by wire brush and removing WPT felt and removing the material retrived exc 500 mtr but not exc 1.50 Km etc complete all as specified and as directed

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm incl mix with water proofing liquid @ 0.15 ltr per 50 kg cement bags as per manufactures instructions complete all as specified and directed.

M&L for rendering 10 mm thick, in cement mortar 1:4, over RCC roof slabs mixed with using water proofing liquid @ 200 ml per bag of cement complete all as specified and directed. Note:- Water proofing liquid shall be measured and paid separately.

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings,benching etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in roof padding finished even and fair and joint filled with mixture of sand and bitumen complete all as specified and as directed

M & L for water proofing treatment to RCC roof by APP based modified polymeric membrane (weight not less than 3.6 kg/sqm) as following step (a)The surface of roof,parapet and gutters,drain mouths etc over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,moss,dust etc by wire brushing and dusting.For cast iron drain outlets a grove shall be cut around to tuck in the treatment.Concrete angle fillets shall be provided at junctions between roofs and vertical faces of wall (parapet and other walls) around obstacles such as pipes chimney stacks, etc and other similar situation to ease up about corners. (b) Primer conforming to IS:3384-1965 @0.30 kg/sqm to be applied on prepared surface,till the surface is properly impregnated. (c) Apply a coat of bitumen 85/25 grade @1.20 kg/sqm over primer. (d) Over the coat of bitumen as above APP modified polymeric membrane ( weight not less than 3.6 kg/sqm) unrolled and bonded completely to the substrate with side over lap of 75mm or end over lap of 100 mm.The overlaps are then sealed/fused by flame or bitumen as per manufacture instruction. A coat of hot blown bitumen grade 85/25 @ 1.20 kg/sqm shall be applied on top of APP modified polymeric membrane and finally it will be finished with a coat of aluminium paint @ 0.20 kg/sqm as per manufacturer instructions.

S&F factory made 35mm thick 100% Solid WPC (Wooden Polymer Composite) Solid Plain Flush Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade) Calcium Carbonate and natural fibers (wood powders/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single Extruded (Inner) with density not less than 650 Kg / cum an ISO 9001-2015 cretified company, having good screw holding capacity (Screw withdrawl strength of 2000 N (Fac) & 1100 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of Elasticity 850 N/mm2 and resistance of spread of flame of class A category with prperty of being Termite / Borer Free, Water / moisture proof, fire retardant and fixing with stainless steel butt hinges of required size with necessary full bodt threaded star headed counter sunk SS screws. All as per direction of Engineer in charge. Material Test certificate and authentication should be compulsory provided by the manufacturing company complete all as specified and directed. Make Kumar Arch Tech Pvt Ltd / Rajshree / Fiber Techno Products / Eco Cell / TVL Engineering Pvt Ltd (Floresta)

S & F 30 mm thick factory made plain wire mesh solid PVC door shutter consisting of frame made out of MS tubes of 19 gauge thickness and size of 19 mm X 19 mm for stiles and 15 mm X 15 mm for top, lock and bottom rails. M.S. frame shall have a coat of metal primer of approved make and manufacturer. 19 mm X 19 mm M.S. square tubes shall be covered with heat molded plain sheet “C” channel made from 5 mm (± 0.25) thick PVC sheet of density 600 kg per Cbm manufactured by an ISO-9001-2015 certified company, of size 30 mm thickness, 115 mm width out of which 100 mm shall be flat and 15 mm shall be bent in 90 degrees angle on either side forming stiles, one of the 90 degrees edge is cut from stiles as well as rails to nail from inner side of door to hide wire mesh fixing steel screws. 5 mm (± 0.25) thick 140 mm wide PVC sheet out of which 125 mm shall be flat and 15 mm shall bent in 90 degrees on the inner side to form top and bottom rail and 155 mm wide PVC sheet out of which 125 mm shall be flat and 15 mm shall be bend in 90 degrees on both side to form lock rail. 4An additional 5 mm (±0.25) thick PVC strip of 20 mm width is to be stuck on the interior side of the “C” channel using PVC solvent cement adhesive. Panel will be of SS wire mesh of 24 gauge to be fitted inside area of stiles & rails. The wide mesh in top, bottom & lock rail is sealed with 15 mm X 15 mm tube with steel screw of size 13/6 mm. 10 mm (5mm X 2Nos) thick PVC strip of 25 mm width is to be stuck & nails on both side of G.I. wire mesh interior at the top, bottom & lock rails. 10 mm thick (5mm X 2 Nos), 20 mm wide cross PVC sheet as gap insert for top rail & bottom rail door to be fixed to frame with 3 nos. M.S. powder coated butt hinges size 100 mm X 25 mm X 2 mm and 32 mm long steel screws drilled suitable to pass through both the walls of the M.S. tube. Other hardware should be fixed with 19 X 6 mm size steel screws etc complete etc as per direction of Engineer-in- Charge, manufacturer’ s specification & drawings. Make : Kumar Arch Tech Pvt ltd / Rajshree / Fiber Techno Products / Eco Cell / TVL Engineering Pvt Ltd (Floresta)

S & F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick pre laminated moulded shutter for kitchen cupboard. The laminated shutter should be 10 mm deep mould on the pre laminated side with different design and other side plain white of density not less than 600 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed. Make Kumar Arch Tech pvt ltd / Rajshree / Fiber Techno Products / Eco Cell / TVL Engineering Pvt Ltd (Floresta)

Supply & fixing factory made WPC door frame 100% Solid (wood polymer composite) Size 100mm x 50 mm Single Rebated ,made from wpc material comparising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as per specifications drawings complete all as specified and directed. Make : M/S Kumar tech , M/s Raj shree ,M/s syntex,Eco cell,TVL Engg Pvt Ltd (Floresta)/Fiber Techno products)

S & F factory made 30mm thick 100% Solid WPC ( Wood polymer Composite ) Solid Plain Flush Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cum an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company.

S&F for mild steel framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

S&F factory made steel windows (Box type) with side hung shutters precoated (colour coated / powder coated) with double shutters (glazed and gauged shutter both) with frame complete all as specified and directed and shown on TD 158 sheets 1/2 & 2/2. Note : Measurements shall be taken and paid compositely for frame, glazed and gauged. Grill shall be measured and paid separately under respective item. No extra claim shall be entertained on this ground.

BLANK

S & F for steel ventilator fixed box type powder coated with glazing bars complete welded including a shop coat of red oxide zinc chrome primer complete all as specified and directed and shown on TD 158 sheets 1/2 & 2/2. Note : Glass shall be measured and paid separately.

Supply only sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. .5 sqm each pane all corner of glass to be fixed complete all as specified and directed.

Supply only 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed

S&Faluminium Anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F Mild steel sliding door bolts 300 mm long , plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as per specified and directed.

S&F 150 mm long aluminium handle, cast type anodised complete all as per specified and directed.

S&F double legged floor door stopper 150 mm long aluminium alloy with rubber etc complete all as specified and as directed

S&F bal catches with 8 mm dia steel ball magnet catches for cuboard shutter including strking plate as approved etc complete all as specified and as directed

S&F continous (piano) hinges, stainless steel with of flap (when open) 30 mm etc complete all as specified and as direced

S&F in repair mild steel helical door spring 150 mm long ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed

S&F in repairs stainless steel decorative curtain rod of 25 mm bore with including brakets 02 nos finalie 02 nos) etc complete all as specified and as directed

S & F glossy finished SS 125 mm hasp and staple including bolt to hinge plate and fixed with S S screws complete all as specified and directed.

S&F 500 litre rotational moulded tripple layer polyethylene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed

S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and as directed

M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases not exc 10cm girth for concealed water tubing etc and making good complete all as specified and as directed

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F vitreous China wash hand basin, size as per manufacturer any design approved by GE, CP brass waste coupling, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed. Make Cera / Hindware / Johnson

S & F Brass CP wall mixer 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make Cera Cat Part No F1016401 / Johnson Cat Part No T5322C / Hindware Cat Part No F570018

S & F Brass CP sink mixer 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed Make Cera Cat Part No F1016501 / Johnson Cat Part No T3420C / Hindware Cat Part No F470023

S & F in repair fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed. Make Cera Cat Part No F7010213AB / Johnson Cat Part No C1709C / Hindware Cat Part No F160006

S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed Make Cera Cat Part No F1016151 / Johnson Cat Part No T3506C / Hindware Cat Part No F130041

S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed Make Cera Cat Part No F1016201 / Johnson Cat Part No T3110C / Hindware Cat Part No F320006

All as per sr item no 79 above but fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and as directed Make Cera Cat Part No F2002362 / Johnson Cat Part No T2515C / Hindware Cat Part No F340006

S & F Brass CP basin mixer 15 mm bore for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed Make Cera Cat Part No F1016451 / Johnson Cat Part No T3517C / Hindware Cat Part No F280010SCP

S&F in repair tubular towel rail 600mm long and 20mm dia D type Brass CP fixed with and including Chromium plated brass screws and wooden/plastic cleats. complete all as specified and as directed

S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

S&F fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S&F fancy type glass corner 300mm radius of 6-8 mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed. Make Parryware Cat Part No T6010A1 / Cera Cat Part No F5005102

S&F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed Make Cera / Hindware / Johnson

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern & flush pipe) and including seat cover complete all as specified and directed. Make Cera / Hindware / Johnson

S&F in repair for Toilet paper holder of brass, chromium plated complete all as specified and directed.

S&F in repair for Hand Shower (Health Faucet) chromium plated with 1.20 Meter long flexible tube and wall hook complete all as specified and directed. Make Cera Cat Part No - F8030107AB / Johnson cat part No S0030C / Hindware Cat part No F160013

S&F in repair for wall mounted PVC bath room cabinet mirror box 400x600x160 mm complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed.

S&F in repair for 75 mm bore out let cast iron floor trap (conforming to IS 3989) incl cockroach trap with gratings including jointing to waste pipe fixed in cement concrete tpe B-1 (1:2:4) etc complete all as specified and as directed

S&F in repair 50 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F in repair for 75 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F in repair for 100 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or vertically cast, complete all as specified and as directed

S&F 75mm bore cast iron Bends , spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 100 mm bore cast iron Bends , spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 75mm bore cast iron Tee, spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 100 mm bore cast iron Tee , spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 50 mm bore cast iron cowls spun pipe (conforming to IS 3989) complete all as specified and as directed

S&F in repair stainless steel sink with drainage board 1.00mm thick for kitchen with plug/waste pipe washers including cantiliver bracket or, connecting unions etc over all size 915 x 460mm with bowel size 410mm x 330mm x 160mm complete all as specified and as directed

S&F for kitchen plate rack stainless steel 1 mm thick of size 90cmx75cm complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed

M & L for ATT post construction Treatment of soil under existing floors using emulsion as per manufacturer instructions @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified.

M & L for ATT post construction along the external wall below concrete or masonry apron using chemical emulsion as per manufacturer instructions @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified

M&L at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface

M&L for PCC 1:2:4 type B-2 using 40mm graded stone aggregates as in foundation, posts filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

S&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

BLANK

M&L for 75 mm thick PCC B-1 1:2:4 (20mm graded aggregate) in floors finish complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge Make JSW Colouron Plus (ISI certified) / TATA Dura Shine ISI Mark

S & F pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge Make JSW Colouron Plus (ISI certified) / TATA Dura Shine ISI Mark

M & L for (595 mm X 595mm) false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI powerd coated tee and cross tee of size 24x32mm & 24x27mm having 0.27mm gauge at every 600mm c/c interval and wall angle of size 19x19mm having 0.35mm gauge fixed to the wall. The above grid is tobe suspended at every 1200mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595x595 mm and ant ine of the design (cascadev or electra) , back of the tile duly sanded and finished with a coat of protective paint over the formed grid etc complete all as specified and directed by Engineer-in-Charge. (Make Everest or equivalent)

S&F framed work as in doors or gates of angle or other section Fe 410 W Gde E 250 with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F 1.00 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete including cutting out of existing sheet if required complete all as specified and directed.

S&F 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate including necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

S&F 1.25 mm thick pressed steel frame of size 105 X 60 mm for door with one ore more rebate including necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

M & L for PCC 1:3:6 Type C-0 using 12.5 mm graded stone aggregate for backing of door chawkhats complete all as specified and directed by Engr-in Charge.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint etc complete all as specified and as directed

M&L for preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

M&L for preparing new wooden surface of any description, not other wise described over 10 cm widht or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed

M&L for preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for three coats of white wash on ceiling on new plastered surfaces including preparation of surfaces complete all as specified and as directed

M&L for two coats of white wash on ceiling on Old plastered surfaces including preparation of surfaces complete all as specified and as directed

M&L for applying two coat of oil bond distemper white or any tint over a coat of primer incl 2 coats of wall care putty on new plastered surfaces complete as specified and directed

M&L for applying two coat of oil bond distemper white or any tint over a coat of primer incl 2 coats of wall care putty on old plastered surfaces complete as specified and directed

M&L for brick work with sub class ‘B’ bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed

M&L for two coats of black bituminous paint on surfaces of any description wood, concrete and brick etc complete all as specified and directed .

Demolition of cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed. Note:- Reinforcement to be measured & paid under respective items.

M&L for form work to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed.

M & L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

S&F 1000 litre ISI marked rotational moulded tripple layer polyethylene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

M & L for Two coats of weather proof exterior emulsion paint over a coat of primer on old prepared surface all as specified in SSR Part I and directed. (Note : The work will be carried out upto triple storey builing the rate of scafolding is included for this item also. Applying coat after completion of preparation of surface and stage has to be passed by Engr-in-charge before complete all as specified and directed) Note The entire work shall be carried out by authorized applicator only with minimum guarantee period in writing.

M & L for Two coats of weather proof exterior emulsion paint over a coat of primer on new plastered surface incl preparation of surfaces all as specified in SSR Part I and directed. (Note : The work will be carried out upto triple storey builing the rate of scafolding is included for this item also. Applying coat after completion of preparation of surface and stage has to be passed by Engr-in-charge before complete all as specified and directed) Note The entire work shall be carried out by authorized applicator only with minimum guarantee period in writing.

M&L for forming letters, figures etc. of 15 cm by cutting 'V grooves in new lime, cement-lime or cement plaster complete all as specified and directed.

M&L for complete removal of existing treatment of wall complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm and getting out in any type of soil complete all as specified.

Removing excavation material surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified & directed.

M& L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed.

M&L for exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick (as approved GE) set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. including 15 ,mm thick cement screed bed in CM 1:6 etc complete all as specified and as directed complete all as specifed and as directed Make Tulip / NTC / Nitco

S&F machine pressed precast concrete interlocking rubberised mould anti fungus paver block any shape and size confirming to IS-15658-2006 of 60 mm thickness M-30 Grade with grey cement and pigments complete all as specified and directed. Make Tulip / NTC / Nitco

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

Returning filling in, incl spreading levelling watering and well ramming in layers n exc 25cm (after the pipes have been laid and tested) in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

Removing excavated material exceeding 250M but not exc 500m and depositing where directed. Complete all as specified and directed by Engineer-In- Charge.

M&L for providing plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed by Engr-In- Charge.

M&L for brick work with old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:4) as in manhole complete all as specified and directed.

M&L for providing precast cement concrete coping with plain fair faces incl chamferes, weathering, throating etc type B0, 1:2:4 using 12.5mm graded stone aggregate complete all as specified and directed by Engineer-In- Charge.

M & L for cement concrete 1:4:8 type D-2 for 150 mm dia in concrete bed to drain pipes including packing under and haunching against the sides of pipes etc complete all as specified and directed by Engineer-In- Charge

M & L for reinforced concrete pipes, 150mm dia class NP-2 laid and jointed complete with collars complete all as specified and directed by Engineer-In- Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge. (Water proofing compound shall be measure and paid separately).

M&L for 10 mm thick rendering on other than fair faces of brick work in CM 1 : 6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipes complete all as specified and directed by Engineer-In- Charge.

M&L for providing factory made precast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab and man hole covers etc complete all as specified and directed by Engineer-In- Charge.

S&F MS Flats, joist channel (Fe 410-W Gde E-250 Quality A), fixed indepently or framed without connecting plates confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

M & L for Construction of septic tank 50 users capacity with excavation and earth work in any type of soil, PCC 1:2:4 type B2 in foundation, old size brick masonry in CM (1:4), RCC M-25 using 20 mm graded crushed aggregate as specified, duly reinforced with 8mm TMT bar @ 120mm c/c manhole covers, angle iron frame, vent shaft and sludge chamber etc. complete all as specified, directed and shown on drawing No TD - 217 sheet 1/7 to 7/7.

BLANK

M&L for soakage well with size 3.0 m dia x 4.5 m effective depth including excavation in any type of soil, foundation in PCC 1:3:6, walls of honeycombed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of old size brick masonry in CM (1:4), RCC cover slab in M-25, interconnecting pipes of RCC complete filled with brick bats complete all as specified and directed.and shown on drawing No TD -309 sheet 1/4 to 4/4.

M & L PCC 1:2:4 type B-0 (using 12.5 mm thick graded stone aggragate) as in surface channel drain. Complete all as specified and directed

Desludging/desilting of 150 mm dia sewage lines including manholes, up to 2.0 m depth by removing blockage if any by means of rodding manually or mechanically by pumping out water where required and removing residual silt/mud/peat/sludge out side of defence land complete all as directed by Engr-in-charge. Note: for item no 148 to 165 the work has to be carried under foul condition, hence the rate to be deemed included.Nothing extra shall be paid to the contractor on this account

BLANK

BLANK

BLANK

BLANK

M&L for PCC 1:3:6 type C-2, (40 mm graded stone aggregate) as in surface channels and drains. (Saucer Drain) complete all as specified and directed

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement incl forms, moulds, mi-tred/stopped ends etc. complete all as specified and directed by Engineer-In- Charge

M&L PCC 1:2:4 type B-2 using 40mm graded stone aggregates as in foundation, posts filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M & L applying two coats of cement based paint over a coat of primer on new plastered surface incl preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

S&F mild steel angles, tees, flats, C section, MS square bars, MS Tubes etc as in steel gates, steel posts and struts in fencing, grills including embedding in concrete and screwing etc. including cut to shape as directed, drilling holes, notching for wire etc including all necessary drilling, bolting, welding or riveting and similar work conforming to FE-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new surface of any description and applying two coats of black Japan paint over a coat of red oxide primer on steel surface over 10cm width or girth complete all as specified and directed by Engineer-in-Charge.

Supply only Chain link MS Galvanised fencing any size or type complete all as specified and directed by Engineer-in-Charge

S & F factory made built in steel cupboard with pressed steel frame of size 75 x 45 x 25mm thick with pressed steel shutter 1mm thick Godrej Pattern fixed to masonry wall by holdfast out of 25 x 3mm flat iron including MS hanging rod of 10mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of MS peg set of 3 pegs, locking arrangement including spray painting with two coats of synthetic enamel paint over a coat of red oxide primer to all around on steel surface of frame and shutter and making good disturbed portion in CM 1:3 or PCC 1:2:4 type B0 using 12.5mm graded stone aggregate complete all as specified and directed.

S & F 1.25mm thick MS Sheet as in cupboard shelf including necessary fixing arrangements complete all as specified and directed.

M & L for chipping of unsound weak concrete / cover of reinforcement over RCC member up to 50mm maximum or as per site requirement by chiseling and disposal of rubbish from site and apply for rust remover cum passivator to remove rust from existing reinforcement and then applying a cement based polymer modified rebar corrosion protection system to existing reinforcement as per instruction of engineer in charge. Make Sika / Fosroc / Dr Fixit

S & F 2mm thick fibre glass reinforced translucent corrugated / plain sheeting with two corrugated side lap fixed with coach screws and washers in roof, wall etc complete all as specified and directed.

M & L for two coats of elastomeric compound on concrete surface after cleaning of sunken portion (vertical or horizontal) by chisel, hammer, wire brush, jute, brush and air blower complete all as specified and directed. Make super latex of Dr Fixit Pidilite-302 super latex / Fosroc Brush Crete / Cico Tapecrete

S & F Stainless steel (AISI 304 grade) non magnetic multilayer nickel chrome plated for multipurpose utensils container including frame work, telescopic channels, handles etc required & complete all as specified and directed, utensils sample, design & pattern of each basket to be approved by GE of following size in each kitchen:- (a) Plain basket of size 510 x 470 x 100mm or 520 x 485 x 100mm or 486 x 500 x 100mm -01 nos Make Sleek Elnora (Asian Paint) Code 600, size 530 x 505 x 150 mm / Godrej Code 6126 baan code LKY2PB214 / Evershine size 520 x 485 x 90mm. (b) Multi size plate basket of size 510 x 470 x 150mm or 520 x 485 x 150mm or 436 x 500 x 200mm (clear depth-500mm) – 01 nos (c) cutlery basket with perforated bottom & side of compacted slots for holding cutlery of size 510 x 470 x 100mm or 520 x 485 x 100mm or 144 x 468 x 50mm (clear depth 500mm) – 01 nos Make Sleek Elnora (Aisan Paint) Code 600, Size 530 x 505 x 100mm / Godrej Product Code 6134 baan code LKY2PC214 / Evershine size 520 x 485 x 95mm Note : Quoted rate for item No. 154 shall be deemed to include the quoted rates for item No. 155. (d) Plain basket of size 510 X 470 X 200 mm or 520 X 485 X 200 mm or 486 X 500 X 200 mm - 02 Nos. (e) Pull out with 02 baskets each of size 150 X 485 X 80 mm or 100 X 485 X 80 mm – 01 Nos Make : Sleek Elnora (Asian paint) Code – 250, size : 180 X 500 X 590 mm / Godrej product code No. 6141, BAAN Code – LKYNS2SP6 / Evershine size 610 X 485 X 90 mm. (f) Dust bin as required – 01 Nos (g) Telescopic channels, handles etc as required incl framework handles complete all as specified and as directed. Note : Sample and design to be approved by GE.

M&L for Udaipur green marble work 18-20 mm thick in single piece without joint, with groove cutting in triple line of stair width, as in staircase and landing, platforms and like, laid over screed bed including pointing in coloured cement with admixture of pigment to match with marble shade incl edge bull nosing, grinding and polishing completely all as specified and directed.

M&L for Udaipur green marble work 18-20 mm thick in riser of steps, skirting incl 15 mm thick rendering in CM (1:4) including pointing in coloured cement in CM (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

Cutting of small trees, bushes including site clearance and removal of debris away from site upto 500 mtr complete all as specified and as directed.

M&L cement concrete tiles 25 cm X 25 cm X 22 mm thick rubber pressed set jointed and pointed in neat cement slurry fixed with grey cement and no pigment over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Fixing only Chain link fencing including line wires,any mesh,size and type to any type of standard, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed by Engineer-in-Charge

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge

M&L in replacement in existing point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in existing concealed PVC conduit 20 mm dia or higher and conduit fittings and all accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of Modular switches, sockets, fan regulator etc with modular white cover plate as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed. Note: (a) Colour code shall be maintained as per IE rule (b) Modular Metal flush box,plate and frame shall be measured and paid seprately.

(a) One light point point / bell buzzer point controlled by one,one way switch.

(b) One ceiling fan/ Exhaust fan point controlled by one,one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two way switch

All as per item No 179 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

M&L for new point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed PVC conduit 20 mm dia or higher and conduit fittings with cutting chases making good to facings where required and pointing in cement mortar 1:3 and all accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of Modular switches, sockets, fan regulator etc with modular white cover plate as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. Note: (a) Colour code shall be maintained as per IE rule (b) Modular Metal flush box,plate and frame shall be measured and paid seprately

(a) One light point point /bell buzzer point controlled by one,one way switch.

(b) One ceiling fan/ Exhaust fan point controlled by one,one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No 186 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

S&F Modular switch 1 way 6A,1 Module SP 230 V AC complete all as specified & directed. Make Legrand / Crabtree / Anchor / Indoasian / Cona

S&F Modular switch 1 way 16A,1 Module SP 230 V AC complete all as specified & directed. Make Legrand / Crabtree / Anchor / Indoasian / Cona

S&F Modular switch 2 way 6A,1 Module SP 230 V AC complete all as specified & directed. Make Legrand / Crabtree / Anchor / Indoasian / Cona

S&F Modular Socket, 6A-2/3 pin combined,2 Module 230 V AC complete all as specified & directed. Make Legrand / Crabtree / Anchor / Indoasian / Cona

S&F Modular socket outlet two in one three pin 6 Amp and 16 Amp flush type complete al as specified. Make Legrand / Crabtree / Anchor / Indoasian / Cona

S&F Modular Bell switch 6 Amp,1 Module complete all as specified. Make Legrand / Crabtree / Anchor / Indoasian / Cona

S&F ding dong bell AC 230 V single pole complete all as specified and directed . Make Legrand / Havells / Wipro

S&F modular fan step type electronic fan regulator two module 100 / 120 Watt complete all as specified and directed . Make Crompton / Bajaj / Havells / Usha

S&F ceiling rose, 3 terminal / PVC / polycarbonate, isolated body 230 V AC complete all as specified and directed . Make Crabtree / Plaza / ESS ESS KAY

S&F lamp holder PVC / polycarbonate type with back plate suitable for batten fittings.230 V AC complete all as specified and directed . Make Crabtree / Plaza / ESS ESS KAY

M&L in replacement sub main wiring with 2 Single core PVC insulated unsheathed FRLS-H cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings with chasing/ cutting and Insulated unsheathed FRLS-H cable copper conductor multistranded of size 6.0 Sq. mm. as earth wire upto common earth and connected to earth dolly complete all as specified & directed including taking down old sub main wiring . Note:- Two runs of 6 Sqmm wire, one run of PVC Conduit and one run of 6 Sqmm Earth wire shall be measured as one unit.

Supply & fixing in replacement and Testing TP & N Vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DB's IK-09 flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable management including Provision of MCCB 63 Amps,ICs=100%ICu, 16KA four pole as in comer including connecting terminal strip complete and SP MCBs as out going etc complete pre wired with suitable size copper conductor. The DB's shall hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Eng-in-charge including taking out old unserviceable DB and removing from site. (Note :- MCB/ MCCB shall be measured and paid separately)

S&F in replacement sheet metal enclosures 240 volt with 200 amps rated copper bus bar for double door 8 way IP-43DB's lk-09suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed by Engr-in-charge ,including taking down old unserviceable DBs . (MCBs shall be measured and paid separately).

S&F MCB double pole 240 Volt 10 KA 40-63 Amp 'B' series conforming to ISI marked complete all as specified & directed .

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed .

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

S&F MCCB 415 Volt 16 KA 4 pole 100 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

Supply & fix in replacement LED light fitting 1x20 W,220V AC decorative box type with driver ,holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: 1) Bajaj Cat Part No - a) BC150 20W WH(For Batten) b) BLRB 20W LED(For Tube) 2) Crompton Cat Part No - a) DIJB12LT.8.20(For Batten) b) LT 8.20-865(For Tube) 3) Havells Cat Part No - a) REGAL BATTEN BUPT01X20W JSBS(For Batten) b)PHOTONULTRAE2.01213T118WLED 865 PC(For Tube)

Supply & fix new LED light fitting 1x20 W,220V AC decorative box type with driver ,holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: 1) Bajaj Cat Part No - a) BC150 20W WH(For Batten) b) BLRB 20W LED(For Tube) 2) Crompton Cat Part No - a) DIJB12LT.8.20(For Batten) b) LT 8.20-865(For Tube) 3) Havells Cat Part No - a) REGAL BATTEN BUPT01X20W JSBS(For Batten) b)PHOTONULTRAE2.01213T118WLED 865 PC(For Tube

S&F LED light fitting mirror type with high out put diffuser 2 feet ,10 watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make: 1) Havells Model - E-LITE LED PRIDE PLUS 2) Polycab Model - INTENSO LXS LED 3) Wipro Cat Part - LL20-111-XXX--65AL1

S&F LED light fitting decorative wall mounting cast aluminium Polycarbonate paint bracket suitable for 5 watts LED bulbwith frosted glass with and including One No 5 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size. Make: 1) Havells Model - FLORETTE WL1LS E14 SS 2) Phillips Model - E27 LED Oval Shape Wall Mount Light 3) Polycab Model - LED WALLMOUNT-2

S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed. Make:-1) PHILIPS Model-Stellar Bright High wattage 15000 life Hrs 2) Bajaj Model No-.LEDZ PLUS BULB 12 Watt 3) Wipro Model - WIPRO TEJAS 12 W B22

Taking down & Refix ceiling Fan 1200 mm sweep single phase 230 volts with down rod , canopy, blades etc including painting of ceiling fan connecting with twisted three cord flaxible copper conductor cable (23/.0076 ) from ceiling rose to connector of fan and writing MES NO on fan complete all as specified and directed.

S&F ceiling fans complete with blades ,down rods ,electronic regulator and accessories ,230 V ,1200mm sweep.Min air delivery 210 CFM with service value 6.00 BEE Five Star Rated with Brushless Direct Current(BLDC) Motor. complete all as specified and directed. Note:(1)Rate for hanging arrangements of Ceiling Fan deemed to be included. (2) Old ceiling fan shall be deposited in E/M storeyard . Make:-1) Bajaj Model No -ENERGOS 35 2) Crompton Model No-.ENERGION HS 1200mm 3) Havells Model No - HAVELLS GLAZE 1200mm BLDC

Supply and fix water heater ,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre,BEE 5 Star rated complete with all accessories such as safety valve ,thermostate ,NRV,connection pipe. complete all as specified and directed. Note:(1) Old Water Heater of any capacity shall be deposited in E/M storeyard. Make:-1) Bajaj Model No -CALENTA 25L 2) Crompton Model No-.ARNO NEO 25L 3) Havells Model No - MONZA EC 25L

Supply & fix exhaust fans steel body AC single phase 230 V of size 300 mm sweep with blades ,frame and louvers.M&L for making Holes of suitable size and making good disturbed surfaces as directed by Eng-in-charge deemed to be included in the quoted rate. complete all as specified and directed. Note: (1) Old Exhaust fan of any capacity shall be deposited in E/M storeyard . Make:-1) Bajaj Model No -MAXX AIR 300mm 2) Crompton Model No-.TRANS AIR 300mm 3) Havells Model No - VENTIL AIR DB 300mm

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm.M&L for making Holes of suitable size and making good disturbed surfaces as directed by Eng-in-charge deemed to be included in the quoted rate complete all as specified and directed. Note: (1) Old Exhaust fan of any capacity shall be deposited in E/M storeyard . Make:-1) Bajaj Model No -MAXIMA DXI 250mm WHITE DOM EX FAN 2) Crompton Model No-.BRISK AIR 250mm 3) Havells Model No - VENTIL AIR DX 250mm

M&L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mmx 6 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15 cm all round the plate using 4 mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead protected in and including 15 mm dia GI ‘medium grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘medium grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as per electrical plate No.3 of SSR Part-II 2010 and testing on completion all as specified and directed. Note (i) If the desired earth resistance is not found within permissible limit (not more than 10 ohm), item shall be re-done by contrcator at no extra cost. (ii) Cost of GI wire 4 sqmm and 15mm dia pipe medium grade upto 7.5m is deemed to be included in the quoted rate for this item.

Supply and Fixing in replacement Integral LED Street Light Luminaire comprising of high pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 36/40 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours including GI brackete made out of 25 mm GI pipe medium grade and MS clamps for fixing of light fitting complete and connected with twin core PVC insulated copper flexible cable with existing point all as specified and directed. Make:-1) Bajaj Cat Part No -ENXT P 36L WH PO PC SD 2) Crompton Model No-.FREEDOM NEO 3) Wipro Cat Part No - LR02-451-XXX-57-G1

Supply and Fixing in replacement Integral LED Street Light Luminaire comprising of high pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 25 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours including GI brackete made out of 25 mm GI pipe medium grade and MS clamps for fixing of light fitting complete and connected with twin core PVC insulated copper flexible cable with existing point all as specified and directed. Make:-1) Bajaj Cat Part No -ENXT P 25L WH PO PC SD 2) Crompton Model No LSTS-25-CDL-M (Astra Neo) 3) Wipro Cat Part No - LR02-291-XXX-57-XX

S&F LED light fitting 1x9W / 1x10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make:-1) Bajaj Cat Part No -BIBWP 10W LED 2) Crompton cat Part No LBHE-10-CDL 3) Wipro Cat Part No - LW07-141-XXX-57-G1

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver,holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make:-1) Bajaj Cat Part No -BZRSQL 43L LED GX PRO WH 2) Crompton Cat Part No LDTLBK-36W-CDL 3) Wipro Cat Part No - LM10-451-XXX-40-G2

Taking down and refixing energy meter fixed in walls/panels of any capacity/any type after carefully disconnecting electrical connections all as specified and directed by Eng-in-charge. Note:- Quoted rate shall deemed to be inclusive of following parameters:- (a) Meter reading shall record shall be submitted before and after replacement duly signed by the contractor rep and MES rep. (b) Old meter should be handed over to MES rep/or in written custody of the Contractor. (c) Any rejoining wires/cables shall be done using suitable ferrule/cable connectors after removal of meter.

S&F post top lantern LED type 40 watt 230 volts AC outdoor type with decorative post top for 360 degree indirect light IP-65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. Make:-1) Bajaj Cat Part No -BGCT W4 LED WH 2) Crompton Cat Part No-LPT0-40-CDL-M 3) Wipro Cat Part No - LP07-431-XXX-57-CL

S&F Single pole and neutral enclosure with a two pin,20 Amp and earth plug and socket complete with one single pole MCB complete all as specified and directed.

S&F of modular Telephone socket RJ11 complete with modular plate fitted on modular GI metal box of 1 module complete all as specified and directed.

S&F rigid ,non-metallic PVC conduit of 20mm external dia, exclusive of boxes(Junction/terminal) but inclusive of all tees,bends,elbows,reducers,bell mouth tube ends and fixing of accessories such as couplers,lock nuts,saddles,pipe hooks etc complete all as specified and directed.

S & F Junction box (1 to 4 way) complete all as specified and directed.

Supply and fixing of GI Metal flush box 1 module, Complete all as specified and directed .

Supply and fixing of 1 Module metal frame with polycarbonate white cover plate ,Complete all as specified and directed .

Supply and fixing of GI Metal flush box 2 module, Complete all as specified and directed .

Supply and fixing of 2 Module metal frame with polycarbonate white cover plate ,Complete all as specified and directed .

Supply and fixing of GI Metal flush box 3 module, Complete all as specified and directed .

Supply and fixing of 3 Module metal frame with polycarbonate white cover plate ,Complete all as specified and directed .

Supply and fixing of GI Metal flush box 4 module, Complete all as specified and directed .

Supply and fixing of 4 Module metal frame with polycarbonate white cover plate ,Complete all as specified and directed .

Supply and fixing of GI Metal flush box 6 module, Complete all as specified and directed .

Supply and fixing of 6 Module metal frame with polycarbonate white cover plate ,Complete all as specified and directed .

Supply and fixing of GI Metal flush box 8 module, Complete all as specified and directed .

Supply and fixing of 8 Module metal frame with polycarbonate white cover plate ,Complete all as specified and directed .

Supply and fixing of GI Metal flush box 12 module, Complete all as specified and directed .

Supply and fixing of 12 Module metal frame with polycarbonate white cover plate ,Complete all as specified and directed .

Supply and fixing of Blank 1 module, complete all as specified and directed.

Supplying, laying in replacement, jointing and testing LT underground cable of size 16 sqmm 4 core heavy duty, 1100 Volts, PVC insulated and sheathed, armoured with multi-stranded aluminium conductor cable conforming to latest IS , laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts duly protected in galvanised steel pipe of suitable sizes all bare conductor of cable duly insulated 1.1 KV grade heat shrinkable sleeve including cable gland and lugging etc at both ends all complete all as specified and directed. Note : Excavation, earth work, cable sand cushioning & cable protection shall be measured separately under relevant items of this schedule.

Supplying, laying in replacement, jointing and testing LT underground cable of size 25 sqmm 4 core heavy duty, 1100 Volts, PVC insulated and sheathed, armoured with multi-stranded aluminium conductor cable conforming to latest IS , laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts duly protected in galvanised steel pipe of suitable sizes all bare conductor of cable duly insulated 1.1 KV grade heat shrinkable sleeve including cable gland and lugging etc at both ends all complete all as specified and directed. Note : Excavation, earth work, cable sand cushioning & cable protection shall be measured separately under relevant items of this schedule.

Supplying, laying in replacement, jointing and testing LT underground cable of size 10 sqmm 2 core ,heavy duty, 1100 Volts, PVC insulated and sheathed, armoured with multi-stranded aluminium conductor cable conforming to latest IS , laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts duly protected in galvanised steel pipe of suitable sizes all bare conductor of cable duly insulated 1.1 KV grade heat shrinkable sleeve including cable gland and lugging etc at both ends all complete all as specified and directed. Note : Excavation, earth work, cable sand cushioning & cable protection shall be measured separately under relevant items of this schedule.

M & L for laying local dry clean sand filling for cushioning in trenches around underground cable complete all as specified and directed.

M&L for laying well burnt brick, old size in trenches, as protection of under ground cable complete all as specified and directed.

Supply and lay in replacement pipe galvanized, “Medium class”, including fittings 40 mm dia complete all as specified and directed. Make Jindal / TATA / Prakash

Supply and lay in replacement pipe galvanized, “Medium class”, including fittings 25 mm dia complete all as specified and directed. Make Jindal / TATA / Prakash

Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 40 mm dia pipe complete all as specified and directed. Make Zolota / Leader / Kirloskar / Venus

Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 25 mm dia pipe complete all as specified and directed. Make Zolota / Leader / Kirloskar / Venus

M&L for construction of brick masonry valve pit of following internally size 600mm x 600mm x 600mm with angle iron 25mm x 25mm x 4mm frame and 2mm thick mild steel plate cover painted with two coats of synthetic enameled paint over a coat of red oxide primer after preparation of surface including locking arrangement, including necessary excavation and earth work 75 mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate over 100 mm thick hard core using broken in foundation/base floor, brick work in cement mortar (1:6) in one brick thick wall and 15mm thick cement plaster in cement mortar 1:4 on internal surface of walls and outside upto 150 mm deep below ground level complete all as specified and directed at site.

Drilling and tapping CI/DI water mains (in position) for branch connections of 15mm internal dia. complete all as specified and directed.

Cutting of existing GI pipe any size for service connection including materials (Tee,bends,reducers etc.) complete all as specified and directed.

Note : Tenderers may note that amount of credit Rs 9,57,395.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

m/s gupta construction