Loading…
Loading…
Tender Value
₹1.9 Cr
EMD Value
₹2.4 L
Closing Date
30 Jan 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
GENERAL
24 conditions · 5 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) Attested Certificates(s) issued by Executive or Nominated Authority of the government Departments or Semi-Government/Public Sector Undertakings for the value of the work done for them during the qualifying period including current financial year certifying the bill amounts paid Agreement-wise and Date-wise or attested photo copy of such certificate. Such certificates will be accepted only from Govt. / Govt. bodies / PSUs authorities. Certificates issued by Private Bodies will not be considered.
NOTE: (i) Financial Year shall normally, be reckoned as 1st April to 31st March of the Next Year. However, for Turnover Criteria, the Financial Year as applicable to the Company /Tenderer is to be considered, if it defers from the above. (ii) Current Financial year is reckoned as the incomplete Financial year in which the date of tender submission falls. (iii) Chartered Accountant statements duly indicating yearly receipts will not be considered until and unless backed by Audited Balance Sheets or Provisional Balance sheet. (iv) (v) If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
If JV firms are allowed to participate; Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.2 of J.V guide lines of IRSGCC April - 2022 [with up to date correction slip].
Definition of similar work: Any Civil Engineering work involving Building work /Concrete work. Tenderer should have valid electrical contractor's license in his/their name or he should give an undertaking that he will engage capable agencies for electrical work who has the valid electrical contractor's license in his/their name.
78 conditions · 29 needing a document upload
Uploading of Proforma -18 attached with Tender document (Certificate signed by Tenderer and Chartered Accountant), w he n balance sheet for the first previous year is yet to be prepared/ audited.
Proforma-16 for self-certificate in regard to meeting the Minimum Local Content requirements as per Make in India Policy for Procurement order value less than of Rs. 10 Crores. OR Proforma-17 for Certificate from the statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of Local Content as per Make in India Policy for Procurement Order Value more than Rs.10 Crores. Provisions of Make in India Policy 2017 (revised during 2024 vide Department for Promotion of Industry and Trade, Ministry of Commerce and Industry's letter No. P-45021/2/2017-PP (BE-II)-Part(4)Vol.II dated 19.07.2024) issued by Govt. of India, as amended from time to time, shall be followed for consideration of tenders.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
(i) The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii) documents shall be submitted according to clause 14 of IRGCC 2022:
This tender complies with PUBLIC PROCUREMENT POLICY ORDER-2017 dated 15.06.2017. Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions. Provisions of Make in India Policy 2017 issued by Govt. of India, as amended from time to time, shall be followed for consideration of tenders.
The General Conditions of Contract governing the performance of the works covered by this tender are the Indian Railway Standard General Conditions of Contract [IRSGCC] as amended from time to time up to date. A soft copy of the Indian Railway Standard General conditions of Contract is uploaded in the attached documents to the tender for reference. Hard copy of IRSGCC (with up-to-date correction slip) may be perused in the office of the Principal Chief Engineer Officer/ South Western Railway / Hubballi - 580020. The tenderer/s is/are deemed to have kept himself/themselves fully Informed of the provisions of the IRS General conditions of Contract including all corrections and Amendments issued up to date while submission of offer and any claim that he/they is/are not aware of any amendment or correction slip to the IRSGCC shall not be entertained.
STUDY OF DRAWINGS AND LOCAL CONDITIONS: The drawings for the works can be seen in the office of the General Manager/Divisional Railway Manager. It should be noted that these drawings are meant for general guidance only and Railway may suitably modify them during the execution of work according to the circumstances without making the Railways liable for any claims on account of such changes. If there is any variation between the description in the tender and the detailed plans, the Engineer-in-Charge will operate the correct description and his decision is final and binding on the tenderer/ Contractor. The Tenderer/Contractor is required to inspect the sites of works and acquaint himself with the site conditions, availability of approaches for transporting of men and materials, space and other factors relating to the works, availability of labour, electricity and water, etc., before quoting his rates. The extent of lead and lift involved in the execution of works and any difficulties involved in the execution of work should also be examined before formulating the rates for complete items of works described in the schedule. The Tender submitted will be deemed to have been made after such inspection.
DRAWINGS FOR WORKS: The percentage rates for the schedule items and itemized rates for the non-scheduled items quoted by the tenderer as may be accepted by the railways will, hold good irrespective of any changes, modifications, alterations, additions, omissions in the locations of structures and detailed drawings, specifications and/or the manner of executing the work. It should be specifically noted that some of the detailed drawings may not have been finalized by the Railway and will, therefore, be supplied to the contractor as and when they are finalized on demand. No compensation whatsoever on this account shall be payable by the Railway Administration. No claim whatsoever will be entertained by the Railway on account of any delay or hold up of the works arising out of delay in approval of drawings, changes, modifications, alterations, additions, omission and the site layout plans or detailed drawings and design and/or late supply of such material as are required to be arranged by the Railway or due to any other factor on Railway Accounts.
Manual tenders, supporting documents etc., sent by Post/FAX/Courier or in Person SHALL NOT BE ACCEPTED.
All requisite documents are to be properly submitted online only and the bidders should ensure that the content of the documents uploaded is distinctly legible /readable.
CORRIGENDUM NOTICE ON IREPS: Railway may modify the tender document by issuing online corrigendum through "www.ireps.gov.in" 15 days prior to the tender closing date. For the purpose of CORRIGENDUM in the tender, NIT period is splitted as under: (a) ADVERTISEMENT PERIOD: The time during which all information pertaining to tender shall be available but offers cannot be submitted (b) OFFER SUBMISSION PERIOD: 15 days prior to closing of tender, during which tenderers can submit their offer.
If the Bid of a Tenderer is seriously unbalanced in relation to the Engineer's estimate of the cost of work to be performed under the contract, the Railways may require the tenderer to produce detailed price analysis for any or all items of the Tender Schedule, to demonstrate the internal consistency of those prices with the construction methods and schedule proposed.
No Technical and Financial credentials are required for tenders having value up to Rs 50 lakh. For tenders valuing more than Rs. 50.00 lakh: The offer of Tenderer(s) who do not enclose Experience Certificate & Turnover Certificate with requisite details, and supporting documents along with their Tender to establish their credentials shall be summarily rejected, even though they are working contractors or contractors on approved list.
The offer shall be evaluated only from the certificates/documents submitted along with the tender offer.
Any Certificate /Documents offered / submitted /received after the tender opening shall not be given any credit and shall not be considered.
Attestation of documents may be self attested or attested by a Gazetted Officer.
Railwayreservestherighttoverifythe authenticityofthe documents/information furnished.
IRSGCC para 6.0 of part-I (a)(ii) Tenderers will examine the various provisions of The Central Goods and Services Tax Act, 2017(CGST)/ Integrated Goods and Services Tax Act, 2017(IGST)/ Union Territory Goods and Services Tax Act, 2017(UTGST)/ respective state's State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt.& as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates. (a)(iii) The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/ UTGST /SGST Act to railway immediately after the award of contract, without which no payment shall be released to the Contractor. The Contractor shall be responsible for deposition of applicable GST to the concerned authority. (a)(iv) In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/ SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority. (b) When work is tendered for by a firm or company, the tender shall be signed by the individual legally authorized to enter into commitments on their behalf. (c) The Railway will not be bound by any power of attorney granted by the tenderer or by changes in the composition of the firm made subsequent to the execution of the contract. It may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.
Increase/decrease of TAXES: if rates of existing GST or cess on GST for Works Contract is increased or any new tax /cess on Works Contract is imposed by Statute after the date of opening of tender but within the original date of completion/date of completion extended under clause 17 & 17A and the Contractor thereupon properly pays such taxes/cess, the Contractor shall be reimbursed the amount so paid. Further, if rates of existing GST or cess on GST for Works Contract is decreased or any tax/cess on Works Contract is decreased / removed by Statute after the date of opening of tender, the reduction in tax amount shall be recovered from Contractor's bills/Security Deposit or any other dues of Contractor with the Government of India.
Fixed Deposit Receipts (FDRs) submitted after award of tender towards Security Deposit/Performance Guarantee should be with automatic renewal facility only.
CONSORTIUM AGREEMENTS AND MOUS SHALL NOT BE CONSIDERED FOR PARTICIPATING IN THIS TENDER.
Tenderer(s) shall note that conditional/alternate offer will not be considered and will summarily be rejected, even though such condition makes them as the lowest tenderer.
Shramik kalyan While processing payment of any 'On Account Bill' or 'Final Bill' or release of 'Advances' or 'Performance Guarantee / Security deposit', contractor shall submit a certificate to the Engineer or Engineer's representatives that "I have uploaded the correct details of contract labours engaged in connection with this contract and payments made to them during the wage period in Railway's Shramik kalyan portal at 'www.shramikkalyan.indianrailways.gov.in' till ____Month, ____Year.
Date of inviting tender shall be the date of publishing tender notice on IREPS website if tender is published on website or the date of publication in newspaper in case tender is not published on website.
Bangalore -Jolarpettai section: SW-I: Proposed construction of 4 units of Type-II quarters at Malur (MLO). SW-II: Proposed construction of Lobby at Running Room cellar at Sir M Vishweswaray Terminal - Bengaluru (SMVB) station. SW-III: Proposed construction of SM rest Rooms at Devangonthi (DKN), Malur (MLO), Bisanatham (BSM) and Varadapura (VRDP) stations including electrical portion. Maintenance period is 12 months. (Composite Tender)
01SBC26OF05-01-26Item-08~SWR
01SBC26OF05-01-26Item-08
Open
Works - General
12 Months
Dharwad, Karnataka
₹0
₹2.4 L
30 Jan 2026
6 Jan 2026
16 Jan 2026
605 items across 12 schedules · ₹1,24,35,954.34 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. | cum | 50 | 411.3 | 20,565 |
| 2 | All kinds of soil | cum | 60 | 205.45 | 12,327 |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | cum | 20 | 253.95 | 5,079 |
| 4 | Foundations, footings, bases for columns | Sqm | 35 | 307.95 | 10,778.25 |
| 5 | Concrete of M10 grade with minimum cement content of 220 kg /cum | cum | 10 | 8,033.2 | 80,332 |
| 6 | Concrete of M15 grade with minimum cement content of 240 kg /cum | cum | 35 | 9,797.15 | 3,42,900.25 |
| 7 | Shelves (Cast in situ) | Sqm | 20 | 766.55 | 15,331 |
| 8 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 500 | 89.65 | 44,825 |
| 9 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 5 | 10,306.2 | 51,531 |
| 10 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 35 | 6,653.45 | 2,32,870.75 |
| 11 | Area of slab over 0.50 sqm | Sqm | 5 | 4,425.35 | 22,126.75 |
| 12 | Granite work | Metre | 8 | 418.85 | 3,350.8 |
| 13 | Second class teak wood | cum | 1.2 | 1,31,576.95 | 1,57,892.34 |
| 14 | 4 mm thick glass pane (weight not less than 10kg/sqm). | Sqm | 40 | 1,897.1 | 75,884 |
| 15 | Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading | Sqm | 20 | 1,521.6 | 30,432 |
| 16 | Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). | Sqm | 40 | 148.5 | 5,940 |
| 17 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 30 | 3,086.1 | 92,583 |
| 18 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). | Sqm | 30 | 401.4 | 12,042 |
| 19 | Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm coir veneer board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete. | Metre | 40 | 626.55 | 25,062 |
| 20 | 20 mm dia | Metre | 40 | 375.25 | 15,010 |
| 21 | Fixed to openings /wooden frames with rawl plugs screws etc. | Kg | 1000 | 197.7 | 1,97,700 |
| 22 | 125 mm | Each | 10 | 205.1 | 2,051 |
| 23 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. | Each | 5 | 1,025.65 | 5,128.25 |
| 24 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. | Each | 5 | 817.5 | 4,087.5 |
| 25 | Size 75 mm | Each | 8 | 355.9 | 2,847.2 |
| 26 | 300x16 mm | Each | 10 | 260.3 | 2,603 |
| 27 | 250x10 mm | Each | 10 | 104.4 | 1,044 |
| 28 | Double strip (horizontal type) | Each | 8 | 34.15 | 273.2 |
| 29 | Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 +/- 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) | Sqm | 1.5 | 7,249.9 | 10,874.85 |
| 30 | Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). | Sqm | 40 | 9,642.6 | 3,85,704 |
| 31 | Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in- charge.(Payment of providing and fixing auto closing hinges shall be paid separately) | Sqm | 15 | 2,563.75 | 38,456.25 |
| 32 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 2000 | 111.95 | 2,23,900 |
| 33 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 75 | 612.25 | 45,918.75 |
| 34 | Size of Tile 600 x 600 mm | Sqm | 60 | 1,359.2 | 81,552 |
| 35 | Size of Tile 600 x 1200 mm | Sqm | 180 | 1,612.75 | 2,90,295 |
| 36 | Size of Tile 600 x 600 mm | Sqm | 15 | 1,311.05 | 19,665.75 |
| 37 | 110 mm diameter | Metre | 10 | 319.75 | 3,197.5 |
| 38 | 1:6 (1 cement: 6 fine sand) | Sqm | 600 | 282 | 1,69,200 |
| 39 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 450 | 214.3 | 96,435 |
| 40 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | Sqm | 150 | 166.85 | 25,027.5 |
| 41 | Two or more coats on new work | Sqm | 450 | 137.85 | 62,032.5 |
| 42 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | cum | 10 | 2,007.1 | 20,071 |
| 43 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 15 | 2,928.1 | 43,921.5 |
| 44 | W.C. pan with ISI marked black solid plastic seat and lid | Each | 2 | 5,426.8 | 10,853.6 |
| 45 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap | Each | 2 | 1,913.75 | 3,827.5 |
| 46 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. | Each | 2 | 1,500.05 | 3,000.1 |
| 47 | 610x460 mm bowl depth 200 mm | Each | 1 | 3,337.85 | 3,337.85 |
| 48 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. | Each | 2 | 299.35 | 598.7 |
| 49 | 40 mm dia | Each | 3 | 104.35 | 313.05 |
| 50 | Rectangular shape 453x357 mm | Each | 2 | 1,158.95 | 2,317.9 |
| 51 | 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms | Each | 2 | 573.6 | 1,147.2 |
| 52 | 25 mm nominal dia Pipes | Metre | 30 | 408.55 | 12,256.5 |
| 53 | 20 mm nominal dia Pipes | Metre | 20 | 513.75 | 10,275 |
| 54 | 15 mm nominal bore | Each | 2 | 434.2 | 868.4 |
| 55 | 15 mm nominal bore | Each | 2 | 594.75 | 1,189.5 |
| 56 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. | Each | 2 | 61.7 | 123.4 |
| 57 | 100 mm nominal dia | Each | 2 | 33.2 | 66.4 |
| 58 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. | Each | 2 | 96.75 | 193.5 |
| 59 | 300 mm dia. R.C.C. pipe | Metre | 15 | 902.05 | 13,530.75 |
| 60 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 250 | 466.3 | 1,16,575 |
| 61 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 75 | 564.8 | 42,360 |
| 62 | Pre-laminated particle board with decorative lamination on both sides | Sqm | 75 | 951.05 | 71,328.75 |
| 63 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | Sqm | 150 | 1,019.8 | 1,52,970 |
| 64 | Upto 5 mm depth and 5 mm width | Metre | 100 | 130.2 | 13,020 |
| 65 | With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles | Sqm | 180 | 2,055.65 | 3,70,017 |
| 66 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 50 | 8,086.6 | 4,04,330 |
| 67 | Cement mortar 1:4 (1 cement : 4 coarse sand) | Sqm | 140 | 913.6 | 1,27,904 |
| 68 | 30 mm thick | Sqm | 6 | 4,327.7 | 25,966.2 |
| Schedule total | ₹43,77,218.19 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .