Additional Ticket Counter work at Transit Camp Rishikesh (Dehradun) Uttarakhand

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete 1:4:8 (1cement :4 coarse sand:08graded brick aggregated 40mm .nominal size.) excluding the cost of centering and shuttering - All work upto plinth level

Centering shuttering including strutting, propping etc. and removalof form work Foundations, footings, bases of columns, etc. for mass concrete

Centering shuttering including strutting, propping etc. and removalof form work Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, cantilevers

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1.5:3 (1 Cement: 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-mechanically treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm ANTI SKID

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion.Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).Powder coated aluminium (minimum thickness of powder coating 50 micron)

ACP Sheet 3.5 mm thick for Partation

Providing Fabricating ,Assembling, painting, Hosting and Erecting in position including detailing of primary Steel Structure M.S RHS/SHS/CHS/Plates of thicknesses as per static analysis conforming to IS 4923/1161/2062 Grade 250MPA in profile . Fabrication of structural elements shall be done using ARC/SAW/MAW/welding process, including transportation, cutting , threading, machining, all leads and lifts up to all height. tools and plants and necessary scaffolding etc. required for all operation, The structural members shall be painted with first coat of Epoxy Primer DFT 30 micron, Final Coat Epoxy Paint 80 microns thick (to be applied in two coats) of which first coat shall be at ground and second coat after erection including touch -up of damaged area of already painted Surfaces if any, uptp all heights including. Designing, Detailing, Providing Fixing including Favrication, Assembling and Erection of roofing material as per Non Linerar Analysis Maintaining a min Safety Coefficient of 4. Roofing Material Should be PES PVC Coated Fabric (Make-Serge Ferrari) with both side PVDF Lacquered/Coated, Weight min 900 gsm, Tensile Strength as per Non Linear Analysis with Safety Coefficient of min 4 and FR retardant. This work shall including raw material , patterning, forming, cutting Seaming(Welding), Fixing and installation with GI cables thickness as per Analysis, flashing, SS Swage End Grade 304 (if any), Galvanized membarane plate with Paint as per Specification etc. Complete as per direction of the Engineer-in- charge. Clamping &Fixing Plate should beAluminium Flat min 4 mm and 4mm thick or as per design requirement. Seam width should be single stroke & minimum 40mm wide. Standard Reducing Warranty on Roofing Material should be 15 year from Roofing Material Manufacturer/ Supplier. Make Serge Ferrari.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P.brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

Providing and Laying of Interlocking Concrete Block Pavements of M-40 Grade having thickness 80 mm as per drawings and Technical Specification Clause 1504. All work Complete as per direction of Engineer - in - charge

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes.

12mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar including drip course/ groove as required as directed by Engineer-in-charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, with pressure 6kg/CM2. 110 MM

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 15 mm

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group (B)

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

3 pin 5/6 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12way , Double door

Providing and fixing circular/ Hexagonal GI box for ceiling fanclamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mmthick GI sheet with its top surface hacked for proper bonding, top lid shall be screwed into the GI box by means of 3.3 mm diaround headed screws, one lock at the corners, clamp shall bemade of 12 mm dia M.S. bar bent to shape as per standard drawing

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.

1 run of cable

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

speaker cable Single pair, 2-core, 1.5 sqmm

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required

Supply of Wall mounted LED 1x20W batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver. as approved by Engineer in charge complete in all respect.

Supply and Fixing of wall fan 400 mm

supply & Installation of Unintedrruptible power Supply type Inverter 2550 VA/2040 W, 220V AC,50Hz, 1 Ph, 12 A,

supply & Installation of Tall Tubular Battery 150Ah, 12 Volt

supply & Installation of Invertor and Tall Tubular Battery Plastic trolly

Supply, installation, testing and comissioning of Digital Video recorder NVR 10 channel, with 1 sata port: video mode: NTSC/ 8MP/6MP/5MP/4MP/3MP/108OP,support 1 SATA port up to 108 TB each HDD support, HDMI video out put 4K(3840x2160) resulation Network, Network: ASDL, Cable Modem, Lan (ethernet), power Supply: DC 12V/5A, power consumption: 40W,

Supply, installation, testing and commissioning of 2 MP,fixed straight BULLET DAY NIGHT WEATHER PROOF IP ,IR with Audio CAMERA,2.8 mmup to 1920x1080@30fps H+265/H.265/H.264 min iSmart IR,IR range : up to 30 M built in mic. Support POE , IP67 POE support, with audio -

Supply, installation, testing and commissioning of 2 MP,fixed straight Dome DAY NIGHT WEATHER PROOF IP ,IR with Audio CAMERA,2.8 mmup to 1920x1080@30fps H+265/H.265/H.264 min iSmart IR,IR range : up to 30 M built in mic. Support POE , IP67 POE support, with audio -

Supply, installation, testing and comissioning of hard disc 4 TB SURVILLANCE HARD DISC

Supply, installation, testing and comissioning of Back Box

S/F of 8+2 SFP port poe 10/100/1000 Gigabite switch

Supply & instalation of Net working 4U rack

Supply & instalation of Net working 9U rack

Supply, installation, testing and comissioning of 32" LED TV Monitor for Observation and reviewing of CCTV display

SITC of HDMI cable 5 mts long

Supply & installation of Cat-6 I/O WITH FACE PLATE & full termination complete

Supply & fixing of Patch cord on rack & 3 mtr. full termination complete

Supply and fixing of 24 port switch with fiber port all accessories with complete

Supply and fixing of 16 port switch with fiber port all accessories with complete

Supplying, installation, testing & commissioning of loud speaker,50 Watt in Horn Type enclosure complete as required

Supplying, installation, testing & commissioning of table top Gooseneck Voice command keypad with microphone assembly complete as required.

Supplying, installation, testing & commissioning of Voice command microphone wire less assembly complete as required.

Sushil Prasad (BID ID -388925)