Interior and renovation work for the office of SIDBI at Bhopal and Vadodara

Name of Work : Interior and Renovation Work for the office of SIDBI at

Vadodra and Bhopal

DETAILED SUMMARY

S.No. Sub-Head NDSR Amount (in Rs.)

Interior renovation work for the office of

Interior renovation work for the office of

TOTAL i/c GST 1,40,32,859.21

Digitally signed by AMIT

Name of Work : Interior and Renovation Work for the office of SIDBI at Vadodra

DETAILED SUMMARY

S.No. Sub-Head NDSR Amount (in Rs.)

1 Civil & Interior Works 5,82,524.08 18,65,664.98

2 Electrical/FA/PA 7,44,625.00 7,19,561.20

4 CCTV AND NETWORK 0.00 1,68,970.00

5 Furniture Work 0.00 15,74,289.00

Add GST Multipluing factor of 1.0633 on

8 TOTAL i/c GST 71,01,459.14

Digitally signed by AMIT

Civil & Interior Works

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

CIVIL AND INTERIOR

1 PARTITIONS AND WALL CLADDING - -

WALL PANELING :-Providing and fixing Paneling upto ceiling height consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick,

fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable

anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50

mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs

at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and

1.1 MR ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid - -

through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of

two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as per manufacture's specification and direction of

engineer in charge all complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Paneling with 12 mm thick HDHMR board to IS: 5509

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick,

fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable

anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50

mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs

at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and

1.2 MR ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid - -

through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of

two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as per manufacture's specification and direction of

engineer in charge all complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Both side 12 mm thick HDHMR board to IS: 5509 SQM 3,850.00 70.00 2,69,500.00

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective

1.3 9.127 surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. - -

Providing and fixing framedglass door/glass partition wherever required 12 mm thickness including all fittings, frames etc. as per direction of

EIC( Floor spring lock and handle paid seprately)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs

or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood cum 1,42,949.70 0.25 35,737.43

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm

1.6 12.62 thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in position by criss cossing GI wire SQM 322.50 80.00 25,800.00

etc. complete as per directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with

1.70 9.21 frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both - -

faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm 2,392.62 10.00 23,926.20

Providing and fixing aluminium extruded section body tubular type universal HS 3000 Slimline Concealed Door Closer (having brand logo with

1.80 MR ISi, IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and door widthfrom 701 mm to 1000 mm), with double speed adjustment each 6,200.02 4.00 24,800.08

with necessary accessories and screws etc. complete

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic AC 10 as per IS : 1868 ), transparent or dyed to

required colour or shade, complete:

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door

stopper with necessary screws, etc. complete.

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123 with Roses & Escutcheon in SS packaged with Mortice

1.11 MR lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all flush doors. EACH 2,750.01 4.00 11,000.04

1.12 MR Providing and fixing 600 mmx25 mm H Type handle for Doors approved make and designs as per engineer in charge EACH 5,505.38 3.00 16,516.14

1.13 MR Providing and fixing minimium 100 kg capacity flooor spring for Doors approved make and designs as per engineer in charge EACH 9,500.00 3.00 28,500.00

1.14 MR Providing and fixing Glass door lock approved make and designs as per engineer in charge EACH 2,650.00 3.00 7,950.00

2.00 CEILING - -

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S.

sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x

1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450

mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x

230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230

mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound ,

jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for

board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding

the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) sqm 1145.95

Providing and fixing mineral fiber falce ceiling With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6 tile m 595x595

2.20 MR moisture resistance frame made glavinised silhoute section as per approved make direction of engineer in-charge Sqm 2,950.00 48.00

CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwood framings hung from ceiling @1000mm

centre to centre with 1 nos of 12mm thk. fire retardant ply on vertical & 12mm thk. Commercial ply on horizontal surface (straight & curved).

Inclusive of finishing in Paint.

2.4 MR Providing the gypsum double sided cove of 150mm x 150mm having a facia of 75mm to macth the specifications same as above RMT 625.00 1.00 625.00

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum ceiling. In order to make the Mineral

2.5 MR Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm as per drawings. (visible surface of gypsum band to not exceed RMT 325.00 10.00 3,250.00

100mm) including plastic emulsion paint.

3.0 FINISHING WORKS - -

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/

litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. - -

3.3 13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. - -

13.85.1 With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre sqm 70.35 285.00 20,049.75

# Providing and fixing wall paneling and partition frame work made of 25x50 mm aluminium section 600x600mm c/c distance as per approved

4.0 MISCELLANEOUS WORKS - -

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

BLINDS Providing & supplying of Window Blinds as per the approved sample in required shade and style consisting, of ZEBRA BLINDS comprising

of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m, Thickness 0.67 mm, Yarn count 18-

19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-5659-2 .Thetear resistance should be complying to ISO4674 & breaking

resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe installation, moulded plastic with steel spring support and

inserted into the tube end. It shall be driven by a ball chain pulley with ball chain and can be positioned at right side or left hand side of the

Shade. The Shade when lowering or raising, shall be automatically locked in position upon release of the ball chain by means of a built in

friction lock.Universal clutch for left and right hand operation.Chain Gear Ratio of 1.75:1. The END PLUG shall be molded of plastic witha steel

location pin.The plug shall be inserted into the tube end.(Opposite to the Drive Unit) for ease of installation. The SUPPORT BRACKETS shall be of

4.1 M.R. coated steel & provided with covers and used in right hand or left hand positions differentiated by the acceptance of the of the rectangular SQM 3,150.00 5.00 15,750.00

drive unit support or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket should be

protruding outside maximum of 80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter & skin thickness of 1mm

and shall incorporate a key way integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom made up of

powder coated steel. The BALL CHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on 6mm pitch to

form an endless ball chain. It is used for raising or lowering action of the shades.

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface as approval of the Architect. (Only film surface area shall

4.2 M.R. be measured and paid). SQM 1,950.01 5.00 9,750.05

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm Laminate of matching, Shutters to be fixed to a frame. Rigidly fixed on

both sides and top finshed in laminate. No internal carcass required. All Hinges of hettich or equivalent. Internal Surface of the shutter in

4.3 MR balancing white laminate. All shutters to be provided with Stainless steel louvers at the top and bottom of the shutter as per the site SQM 13,342.01 2.00 26,684.02

requirements and instrcution of the Engineer In charge.

Providing and Fixing Logo & Signage in 3D ,as per the approved Design/ pattern with Mat /Gloss Finish Brass Letters with Mettalic/ Acrylic Base,

complete as required at site with the direction of the Enginner In Charge

Providing and Fixing of floor tiles with wear layer is of 0.5mm, made upof Stone Polymer composite, 100% Water & Termite proof, Scratch/

Flame/ UV resistant, anti-microbial, 100% recyclable Green product having click system with suitable skirting. Classification of abrasion

4.5 MR resistance (Abrasion wheelfromH-18 Calibrade, loadApplied 1000 grams, No. of Cycles 14,400). " ( Along with Matching Profiles) SQM 3,750.00 80.00 3,00,000.00

OUTER AREA 3D ACRYLIC SIGNAGE

4.6 Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of required size and shape with arrangement of screws in the letters itself for mounting on the

walls or pasting using 3M VHP Tape. Fixing complete as per directions of the engineer. The Sizes would be calculated in Sqft as per Logo Design provided.

MR Tentative Size 42"X180" Each 215650 1.00 215650.00

Digitally signed by AMIT

Electrical/FA/PA

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

1.0 DISTRIBUTION BOARDS.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess,

complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles

1.2 in the existing MCB DB complete with - -

connections, testing and commissioning etc. as required.

2.15 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a

1.4 sensitivity current 30 mA in the existing MCB DB - -

complete with connections, testing and commissioning etc. as required.

2.0 CABELS / MAINS - -

Supply ,laying,testing and commissoning of 1100V grade armoured cable having sector / circular shaped aluminium / copper

conductor PVC insulated cores under ground PVC tape wrapped inner sheathed, GI strip / wire armoured and overall extruded PVC

sheathed confirming to IS: 1554, laid on wall or ceiling using GI clamps and spacers as per route shown at site and further as directed by - -

Engineer-in charge

2.1 MR 16 Sq.mm 4 core copper cable mtr. 725.00 20.00 14,500.00

2.1 MR 25 Sq.mm 4 core copper cable mtr. 1,250.00 50.00 62,500.00

4.0 WIRING - -

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable

in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq.

mm FRLS PVC insulated copper

4.2 1.54 conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper - -

conductor single core cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core

4.3 1.7 cable in surface/ recessed steel conduit as required. - -

a 1.7.1 2x1.5sqmm+1x1.5sqmmearth wire Per mtr. 327.00 150.00 49,050.00

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for twin control point wiring using 1.5 sqmm copper conductor FRLS PVC insulated copper conductor cable drawn through 25

4.4 1.4 dia MS conduit laid in surface/concealed over false ceiling or in slab/wall chases including ,2way modular switches,modular plate Per Pts 1,981.00 20.00 39,620.00

,suitable GI box and earthing the point with 1.5 sqm FRLS PVC insulated copper conductor single core cable as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding

modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 122.00 60.00 7,320.00

d 1.24.5 6 pin 15/16 A socket outlet Each 197.00 20.00 3,940.00

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as

4.7 1.28 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. - -

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

4.9 MR Supplying and laying HDMI Cable with connector on both ends upto 15m length or as per site requirement Each 2,565.59 2.00 5,131.18

5 LIGHTING FIXTURES - -

Supply, Installation, Testing and Commisioning of pre-wired round shape Surface Mount 15Watt LED Down Lighter fitting complete with

all accessories, housing made of Aluminium Die-cast, System Efficasy >100 LPW, CRI >80, CCT of 4000K. suitable for 220 V, 50 Hz, The

luminare rated life (L70) >50000 Hours with High efficiency driver with inbuild surge protection, over voltage protection, short circuit

5.2 MR protection and operating at >0.95 PF., BIS approved Driver including connection with 1.5 sq. mm FR PVC insulated, copper conductor, NOS 1,270.91 60.00 76,254.60

single core cable and earthing etc as required.

Supply, Installation, Testing and Commisioning of 600X600 36-40Watt LED fitting complete with all accessories, housing made of

Aluminium Die-cast, System Efficasy >100 LPW, CRI >80, CCT of 4000K. suitable for 220 V, 50 Hz, The luminare rated life (L70) >50000 Hours

5.5 MR with High efficiency driver with inbuild surge protection, over voltage protection, short circuit protection and operating at >0.95 PF., BIS NOS 2,650.00 20.00 53,000.00

approved Driver including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc as

6 WIRING FOR DATA AND VOICE OUTLETS - -

Supply and fixing the following sizes of PVC medium duty ISI marked conduits (IS : 9537 Part-III) complete with accessories such as

6.1 bends, junction boxes, pull boxes etc., in recess or on surface including cutting chases in the walls/floors and making good the same - -

complete as required.

Supplying and drawing of CAT 6A U/UTP cable, white jacket, 4 pair LAN Cable in the existing surface/ recessed Steel/ PVC conduit as

Supply & fixing of Plug in type information outlet (campatible with data cables) in existing faceplate/ GI Box in wall/furniture/floor

6.3 MR complete as required. Nos. 482.51 60.00 28,950.60

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding

modular plate etc. as required.

1.24.6 Telephone socket outlet Each 148.00 40.00 5,920.00

6.5 Supply and fixing of the following types Face Plates complete with all accessories. - -

Supply & Fixing of Dual Faceplate, Duplex Port (for data and for voice) or as required square plate having spring shuttered front access

a. MR for preventing ingress of dust, dimension as per commercially available modular office furniture. Nos. 90.04 40.00 3,601.58

Supply ,laying ,installing , testing and commmissioning of the 50 pair multi core 0.61 mm annealed copper conductor PVC insulated and

6.6 MR PVC sheathed armoured telephone cables generally conforming to ITD S/WS-11-C and IS 1554 part I direct in ground /surface and / or mtr. 380.57 50.00 19,028.50

in existing pipe as required and includig making terminal joints, complete as required.

Supplying, installing, testing and commissioning of 24 port Cat 6A patch panels available with block of four equipped with tool less IO,

6.7 MR Rack Mountable. 19" Modular Patch Panel, loaded CAT6A U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool EACH 14,491.19 1.00 14,491.19

less connector U/UTP unit in a block.

7 CABLE TRAY.& RACE WAY. - -

7.2 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only) - -

MR Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with internal partition/compartmentized of the

following sizes including providing removable 3 mm thick GI cover, knock out holes and fixing accessories earthing with 8 SWG copper

earth wire complete as required including floor supports, bends, access boxes, tap off boxes and cross over as per specification and - -

site requirement. (overhead / wall mounted recovery & function boxes shall be 1.6 mm thick)

c) MR 150 mm wide x 38 mm deep raceway or as per site RM 1,503.10 10.00 15,031.00

d) MR 100 mm wide x 38 mm deep raceway or as per site RM 1,150.00 10.00 11,500.00

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

MR Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as

per specification.

A. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : - -

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base Pcs

complete as required.

2 17.2.14 Supplying, installation, testing & commissioning of addressable manual call point complete as required. Pcs 3871.00 1.00 3,871.00

3 17.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. Pcs 3506.00 1.00 3,506.00

4 17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required. Pcs 3270.00 1.00 3,270.00

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover Pcs

complete with all connections etc as required.

Supply onstallation testing and commissioning of 2 loop conventional fire panel as per direction of engineer in charge

Two loop panel Each 26550.00 1.00 26,550.00

B CABLES & ACCESSORIES FOR FAS : - -

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, RM

600/1000V rated with annealed copper conductor having

XLPE insulation, steel wire armouring & FRLS outer sheath

complete as required.

C SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES : - -

SUB HEAD (H) : UPS SYSTEM - -

Supplying, installation, testing and commissioning of (N+1) 10 kVA/27KW online double conversion fully microprocessor based ,indoor

type, compact UPS system of mentioned rating with designed output PF .9 at 40 degree and IGBT based PWM technology to achieve

THD < 5% and input power factor of greater than 0.95 at 50% loading, Efficiency >= 93% at 50 % load, suitable for three phase AC input

13 MR voltage 320 V to 480 V, 50 Hz +3% / - 3 % and three phase AC output voltage 415 ± 1% volts & frequency 50 ± 0.5 Hz with all components - -

as mentioned in BOQ, specifications and schedule, complete as required and as per technical specification. Each unit shall be

comprising of the following: Total 2 no.s (In parallel)

125% rated Rectifier cum charger unit +100% rated Invertor, Integrated in UPS module - -

100% rated Inbuilt static switch at the invertor output + 2 Nos. 100% rated Inbuilt static switches at the static bypass line. - -

100% rated Inbuilt Maintenance Bypass. - -

Web-enabled Monitoring and Management through SNMP protocols for multi-OS environments. - -

Inbuilt feature required for input phase seq protection and automatic change. UPS should work on mains and should not go to battery

mode in case of input phase sequence change

Supplying, unloading, installing testing and commissioning of necessary VRLA batteries of suitable size having 15 minutes back up time

to 30KVA UPS for full load (75Ah Batteries X 20 No.) to be provided. 1 No spare batteryof same AH to be provided and cost to be added.

Total VAH = 18000VAH

Note : Concerning vendor needs to furnish the battery sizing calculations at the time of GA approval and battery size has to be as per

the approved GA drawing.

Run the battery diagnostic test. - -

Automated unattended shutdown of computers. - -

Local notification through audible alarm. - -

Software should support :

latest version of Microsoft Windows/ Server, AIX, HP-UX, Sun Solaris, Linux, Novell Netware, MAC

Total DSR & Total Non DSR 7,44,625.00 7,19,561.20

Digitally signed by AMIT

VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable

Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP

modules, microprocessor based Controller, top discharge type condensing unit(s), with R410A

1.0 1.1 Refrigerant, vibration isolators, with suitable foundation etc. complete as required.The unit shall Per HP 16415 20.00 3,28,300.00

deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without

tripping.The unit shall be suitable to work on 400V+/-10%, 3 Phase, 50Hz AC power supply.The unit

shall be filled with first charge of the refrigerant and ready for use as required.The COP at AHRI

conditions shall not be less than 3.1 and IEER not less than 6.5 .

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following minimum capacity 4-wayflow VRV/ VRF

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan

section with low noise fan/ dynamically balanced blower, multi speed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports,

vibration isolation, cordless remote control etc., suitable for operation on single phase 230V±10%, 50

HzAC supply, complete, as required. The unit shall have automatic force shut down provision in case

of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inl et

conditions of 27 Degree CD Band 19 Degree CWB temperature.

4-Way Cassette type - -

3.0 REFRIGERANT PIPING - -

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete

with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including

3.0 VRF/VRV - -

accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid

lines, all accessories as per specifications etc. as required :

3.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 331.0 180.00 59,580.00

3.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 466.0 40.00 18,640.00

3.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 588.0 90.00 52,920.00

3.5 5.5 19.2 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 707.0 40.00 28,280.00

3.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 865.0 40.00 34,600.00

Digitally signed by AMIT

VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

3.8 5.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation Rmt 1230.0 30.00 36,900.00

4 CONDENSATE DRAIN UPVC PIPE - -

Supply, installation, testing and commissioning of uPVC Pipe ,complete with fittings, supports,U trap

arrangement,Clean Plug with 6mm nitrile insulation and accessories as per specifications, drawings.

4.3 MR Imported fittings Y-joints and headers etc. Nos 3281.4 8.00 26,251.20

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper in suitable conduits between indoor

and outdoor unit.

MR Supply and fixing IP-55 based outdoor MCB box with 1 NOS 65 amp RCCB Nos 12650.0 1.00 12,650.00

MR Supply and fixing MS base frame for VRV outdoor stand as per approved size NOS 4500.0 1.00 4,500.00

SITC of individual 1.5 tr split ac for server room as per approved Nos 78550.0 1.00 78,550.00

Supply installation testing and commissioning Treated Fresh Air HRV capacity 800 CFM for Fresh Air Ventilation as per approved

2 MR-2 Providing and fixing of 24 gaze GI Ducting rectangular as per required SQFT 330.00 200.00 66,000.00

3 MR-3 Providing and fixing of Aluminium flexible Duct NOS 6,844.00 4.00 27,376.00

4 MR-4 Providing and fixing powder coted louver and birdscreen for fresh air wall opening LOT 19,500.00 1.00 19,500.00

5 MR-5 Providing and fixing of canvas connection NOS 8,210.00 1.00 8,210.00

6 MR-6 Providing and fixing Grill NOS 2,200.00 8.00 17,600.00

Digitally signed by AMIT

Sr. No. Item Description Unit Rate Qty Amount

1 Supply, Installation, Testing & Commissioning of 24 PORT Managed Network Switch Unit 42,650.00 1 42,650.00

Supply, Installation, Testing & Commissioning of 2.5MP IR IP H.265 Vandal Proof Dome camera with 2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple streams,3-Axis, IP67,

IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Crossing line,

Motion detection, Object left, Missing object,Intelligent Identification Face detection, Defocus, Scene Change,PoE (IEEE802.3 af) Power consumption: Max

7.2W,Edge Storage Micro SD Card, Up to 256GB, ANR Support,Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-condensing),Compatible

Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing and Commissioning of 16Ch Embedded Network Video Recorder with 4 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,

RAID, Redundant power supply, Smart Analytics and ONVIF

3 SITC of SSD Hard Disk Drive 4TB, 24/7 surveillance category Only complete etc as required.etc.all complete. Nos 19,500.00 1 19,500.00

C. 20 Pair MDF Box -

1 20 Pair MDF Box with mounting Frame Nos. 5,500.00 1 5,500.00

Digitally signed by AMIT

Specifications Rate Qty Amount

DGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made out of 25mm thick pre -laminated particle board of approved shade. The

working and non working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported with MS powder coated "C" shape leg of

size 50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table

shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & one

1 open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18mm thick pre laminated 55,803 1.00 55,803.00

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension (L)1800mm X (D) 900mm X

(H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

DGM High Back Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically

Chair design contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The chrome plated loop

armrest with padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star

chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/-2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

DGM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X (H)990mm.A contemporary design with an all black finish, . Material &

Back Chair subtype:Premium Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever,

Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35

3 kg/m3. The backrest has a foam of 28kg/m3. 17,640 3.00 52,920.00

2 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft cushioned backrest and seating. Material & subtype:Premium Leatherette,

Colour & Colour Family:as per requirement, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech solid wood have

used for framing construction of sofa .The seat cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The

4 thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater Dimension(L)1390mm X 38,250 2.00 76,500.00

AGM/BMO Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made out of 25mm thick pre -laminated particle board of approved shade. The

working and non working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported with MS powder coated "C" shape leg of

size 50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table

shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & one

5 open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18mm thick pre laminated 50,085 3.00 1,50,255.00

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site requirement. Main Table Dimension (L)1800mm X (D) 900mm X

(H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

AGM High Back Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water

Chair proof plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it.

The chair shall be provided with self tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height

6 adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed plywood upholstered with 20,322 3.00 60,966.00

PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Conference Supplying and placing in position of conference table of required size as per image/drawing. The work surface top should be of thickness 42mm top prelaminated particle board

Table with 2mm thick PVC edge banding. The side panel are made up of 36mm thick prelaminated particle & modesty panel are made out of 25mm thick prelaminated particle board

7 with 2mm thick PVC edge banding. The wire carrier should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a provision of 6 module flip top box & 85,500 1.00 85,500.00

metal raceway for wire flow.

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be

chair ergonomically design contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The chair shall be

8 provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 14,850 28.00 4,15,800.00

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg /m3) The backrest has a foam of 28kg/m3.

lenior Dimesnion: 1200mm(L)x 600mm(D) x 750mm(H) Modular Workstation With 1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side laminated

Workstation and upper tile inside side fabric, White Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end 18mm thick MDF board., and 3Drawer top

9 supported Pedestal unit Size 400W x 400D x 725H made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For drawer Facia-Honkong Blue, Fabric- 23,850 12.00 2,86,200.00

F 161 Dolphin Blue, Powder Coating-Munshel Gray. and White Tinted Glass( mobile vanity paid sepretly)

Mobile vanity 3Drawer top supported Pedestal unit Size 400W x 400D x 725H made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For drawer Facia-

10 Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-Munshel Gray. and White Tinted Glass 8,800 12.00 1,05,600.00

Digitally signed by AMIT

Specifications Rate Qty Amount

Reception Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made out of 25mm thick pre -laminated particle board of approved shade. The

working and non working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported with MS powder coated "C" shape leg of

size 50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table

shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & one

11 open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18mm thick pre laminated 34,740 1.00 34,740.00

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site requirement. Main Table Dimension (L)1350mm X (D) 900mm X

(H)750mm overall Side Runer Dimension (L)1200mm X (D) 450mm X (H) 675mm

Pantry Table Providing & Installation of Pantry table of size 1.2m x .9m x 1.05m (ht) made out of 19mm thk. Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as

per design. The Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above table. One (1) number Drawer pedestal with 3 drawers to be

12 provided under the table. 16,695 2.00 33,390.00

13 Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC 2,205 12.00 26,460.00

14 TABLE CENTRE TABLE WITH GLASS TOP 16,500.00 1.00 16,500.00

15 TABLE SIDE TABLE WITH WOODEN STRUCTURE 11,250.00 1.00 11,250.00

Openable Shutter The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made of 09mm thick MDF of approved shade. All the edges of storage surface shall

storage be provided with machine pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle and suitable lock. All exposed area PVC edge

DGM back side 1050WX450DX750H 14,850.00 2.00

Total Amount 15,74,289.00

Total Amount 15,74,289.00

Digitally signed by AMIT

Name of Work : Interior and Renovation Work for the office of SIDBI at BHOPAL

DETAILED SUMMARY

S.No. Sub-Head NDSR Amount (in Rs.)

1 Civil & Interior Works 7,62,857.13 19,34,771.63

2 Electrical/FA/PA 6,41,728.00 2,77,602.42

4 CCTV AND NETWORK 0.00 2,02,970.00

5 Furniture Work 0.00 17,10,056.50

Add GST Multipluing factor of 1.0633 on

8 TOTAL i/c GST 69,31,400.06

Digitally signed by AMIT

Civil & Interior Works

S No. Description Unit Rate Total Qty DSR Amount NDS Amount

CIVIL AND INTERIOR

1 PARTITIONS AND WALL CLADDING - -

WALL PANELING :-Providing and fixing Paneling upto ceiling height consisting of Aluminium frame and required board, frame

work made of Aluminium section made of 50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges

of 25 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5

mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having

one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and

placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of

partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to

centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at

1.1 MR the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through - -

cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal

joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as per

manufacture's specification and direction of engineer in charge all complete.(Cost of Aluminium framing 600X600mm Paid

Paneling with 12 mm thick HDHMR board to IS: 5509

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of Aluminium frame and required board, frame

work made of Aluminium section made of 50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges

of 25 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5

mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having

one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and

placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of

partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to

centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at

the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through - -

cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal

joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as per

manufacture's specification and direction of engineer in charge all complete.(Cost of Aluminium framing 600X600mm Paid

Both side 12 mm thick HDHMR board to IS: 5509 SQM 3,850.00 70.00 2,69,500.00

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density

1.3 9.127 protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive - -

of approved quality.

Providing and fixing framedglass door/glass partition wherever required 12 mm thickness including all fittings, frames etc. as

per direction of EIC( Floor spring lock and handle paid seprately)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position

1.5 9.1 with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). - -

9.1.1 Second class teak wood cum 1,42,949.70 0.25 35,737.43

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48

1.6 12.62 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in SQM 322.50 80.00 25,800.00

position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.

Digitally signed by AMIT

S No. Description Unit Rate Total Qty DSR Amount NDS Amount

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board

1.70 9.21 construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross - -

bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm 2,392.62 10.00 23,926.20

Providing and fixing aluminium extruded section body tubular type universal HS 3000 Slimline Concealed Door Closer (having

brand logo with ISi, IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and door widthfrom 701 mm to 1000 mm),

1.80 MR with double speed adjustment with necessary accessories and screws etc. complete each 6,200.02 5.00 31,000.12

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic AC 10 as per IS : 1868 ),

1.90 9.97 transparent or dyed to required colour or shade, complete: - -

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door

1.10 9.82 stopper with necessary screws, etc. complete. EACH 121.65 5.00 608.25

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123 with Roses & Escutcheon in SS packaged

1.11 MR with Mortice lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all flush doors. EACH 2,750.01 5.00 13,750.05

1.12 MR Providing and fixing 600 mmx25 mm H Type handle for Doors approved make and designs as per engineer in charge EACH 5,505.38 4.00 22,021.50

Providing and fixing minimium 100 kg capacity flooor spring for Doors approved make and designs as per engineer in charge

Providing and fixing Glass door lock approved make and designs as per engineer in charge

2.00 CEILING - -

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power

pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of

angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange

fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5

mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,

shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230

mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and

30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry

2.1 12.45 wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry - -

wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of

the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto

150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably

fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) sqm

Providing and fixing mineral fiber falce ceiling With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6

2.20 MR tile m 595x595 moisture resistance frame made glavinised silhoute section as per approved make direction of engineer in- Sqm 2,950.00 65.00

charge 1,91,750.00

CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwood framings hung from ceiling

2.3 MR @1000mm centre to centre with 1 nos of 12mm thk. fire retardant ply on vertical & 12mm thk. Commercial ply on horizontal RMT 860.00 5.00 4,300.02

surface (straight & curved). Inclusive of finishing in Paint.

Providing the gypsum double sided cove of 150mm x 150mm having a facia of 75mm to macth the specifications same as

Digitally signed by AMIT

S No. Description Unit Rate Total Qty DSR Amount NDS Amount

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum ceiling. In order to make

2.5 MR the Mineral Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm as per drawings. (visible surface of gypsum RMT 325.00 10.00 3,250.01

band to not exceed 100mm) including plastic emulsion paint.

3.0 FINISHING WORKS - -

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and

smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less

3.2 13.83 than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve - -

even shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound )

13.85.1 With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre sqm 70.35 380.00 26,733.00

Providing and fixing wall paneling and partition frame work made of 25x50 mm aluminium section 600x600mm c/c distance as

per approved make

4.0 MISCELLANEOUS WORKS - -

BLINDS Providing & supplying of Window Blinds as per the approved sample in required shade and style consisting, of ZEBRA

BLINDS comprising of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m,

Thickness 0.67 mm, Yarn count 18-19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-5659-2 .Thetear

resistance should be complying to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy

and safe installation, moulded plastic with steel spring support and inserted into the tube end. It shall be driven by a ball chain

pulley with ball chain and can be positioned at right side or left hand side of the Shade. The Shade when lowering or raising,

shall be automatically locked in position upon release of the ball chain by means of a built in friction lock.Universal clutch for

left and right hand operation.Chain Gear Ratio of 1.75:1. The END PLUG shall be molded of plastic witha steel location pin.The

plug shall be inserted into the tube end.(Opposite to the Drive Unit) for ease of installation. The SUPPORT BRACKETS shall be of

coated steel & provided with covers and used in right hand or left hand positions differentiated by the acceptance of the of

the rectangular drive unit support or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame (d) in

Recess. The Bracket should be protruding outside maximum of 80mm.The ROLLER TUBE shall be of extruded aluminum with

37mm internal diameter & skin thickness of 1mm and shall incorporate a key way integral with the tube to accommodate the

spline. The BOTTOM RAIL shall be a Flat Bottom made up of powder coated steel. The BALL CHAIN shall be 2mm diameter cord

with 4.5mm diameter acetal balls moulded co-axially to it on 6mm pitch to form an endless ball chain. It is used for raising or

lowering action of the shades.

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface as approval of the Architect. (Only film

4.2 M.R. surface area shall be measured and paid). SQM 1,950.01 20.00 39,000.19

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm Laminate of matching, Shutters to be fixed to a frame.

Rigidly fixed on both sides and top finshed in laminate. No internal carcass required. All Hinges of hettich or equivalent. Internal

Surface of the shutter in balancing white laminate. All shutters to be provided with Stainless steel louvers at the top and bottom

of the shutter as per the site requirements and instrcution of the Engineer In charge.

Providing and Fixing Logo & Signage in 3D ,as per the approved Design/ pattern with Mat /Gloss Finish Brass Letters with

4.4 MR Mettalic/ Acrylic Base, complete as required at site with the direction of the Enginner In Charge sq inch 20.00 3500.00 70000.00

Providing and Fixing of floor tiles with wear layer is of 0.5mm, made upof Stone Polymer composite, 100% Water & Termite proof,

Scratch/ Flame/ UV resistant, anti-microbial, 100% recyclable Green product having click system with suitable skirting.

4.5 MR Classification of abrasion resistance (Abrasion wheelfromH-18 Calibrade, loadApplied 1000 grams, No. of Cycles 14,400). " ( SQM 3,750.00 80.00 3,00,000.00

Along with Matching Profiles) incuding leveling , civil repair as per site condition.

OUTER AREA 3D ACRYLIC SIGNAGE

Digitally signed by AMIT

S No. Description Unit Rate Total Qty DSR Amount NDS Amount

4.6 Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of required size and shape with arrangement of screws

in the letters itself for mounting on the walls or pasting using 3M VHP Tape. Fixing complete as per directions of the engineer.

MR The Sizes would be calculated in Sqft as per Logo Design provided. Each 215650 1.00 215650.00

Tentative Size 42"X180"

4.7 Dismentaling of bricks/tiles/ false ceiling/pcc/rcc/ electrcial points,/wires/cables /DB/ duct etc as per site conditions and

dispose of malba as per direction of engineer in charge as per site condition.

Digitally signed by AMIT

Electrical/FA/PA

DSR-2022 Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

1.0 DISTRIBUTION BOARDS.

2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution

board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/Isolator)

2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for

1.2 inductive load of following poles in the existing MCB DB complete with - -

connections, testing and commissioning etc. as required.

2.15 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current

1.4 circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB - -

complete with connections, testing and commissioning etc. as required.

2.0 CABELS / MAINS - -

Supply ,laying,testing and commissoning of 1100V grade armoured cable having sector / circular

shaped aluminium / copper conductor PVC insulated cores under ground PVC tape wrapped inner

sheathed, GI strip / wire armoured and overall extruded PVC sheathed confirming to IS: 1554, laid on - -

wall or ceiling using GI clamps and spacers as per route shown at site and further as directed by

Engineer-in charge

2.1 MR 16 Sq.mm 4 core copper cable mtr. 725.00 20.00 14,500.00

2.1 MR 25 Sq.mm 4 core copper cable mtr. 1,250.00 30.00 37,500.00

4.0 WIRING - -

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed medium class PVC conduit, with modular

switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

4.2 1.54 conductor single core cable in surface/ recessed medium class PVC, and earthing the point with 1.5 - -

sq. mm FRLS PVC insulated copper conductor single core cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated

4.3 1.7 copper conductor, single core cable in surface/ recessed medium class PVC as required. - -

a 1.7.1 2x1.5sqmm+1x1.5sqmmearth wire Per mtr. 327.00 120.00 39,240.00

c 1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Per mtr. 428.00 120.00 51,360.00

Digitally signed by AMIT

DSR-2022 Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

Wiring for twin control point wiring using 1.5 sqmm copper conductor FRLS PVC insulated copper

conductor cable drawn through 25 dia medium class PVC laid in surface/concealed over false

ceiling or in slab/wall chases including ,2way modular switches,modular plate ,suitable GI box and

earthing the point with 1.5 sqm FRLS PVC insulated copper conductor single core cable as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box

including connections but excluding modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 122.00 60.00 7,320.00

d 1.24.5 6 pin 15/16 A socket outlet Each 197.00 80.00 15,760.00

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular

switches in recess etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated,

4.8 1.19 shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed Meter 47.00 40.00 1,880.00

steel/ PVC conduit as required.

Supplying and laying HDMI Cable with connector on both ends upto 15m length or as per site

5 LIGHTING FIXTURES - -

Supply, Installation, Testing and Commisioning of pre-wired round shape Surface Mount 15Watt LED

Down Lighter fitting complete with all accessories, housing made of Aluminium Die-cast, System

Efficasy >100 LPW, CRI >80, CCT of 4000K. suitable for 220 V, 50 Hz, The luminare rated life (L70) >50000

5.2 MR Hours with High efficiency driver with inbuild surge protection, over voltage protection, short circuit NOS 1,270.91 46.00 58,461.67

protection and operating at >0.95 PF., BIS approved Driver including connection with 1.5 sq. mm FR

PVC insulated, copper conductor, single core cable and earthing etc as required.

Supply, Installation, Testing and Commisioning of 600X600 36-40Watt LED fitting complete with all

accessories, housing made of Aluminium Die-cast, System Efficasy >100 LPW, CRI >80, CCT of 4000K.

suitable for 220 V, 50 Hz, The luminare rated life (L70) >50000 Hours with High efficiency driver with

inbuild surge protection, over voltage protection, short circuit protection and operating at >0.95 PF.,

BIS approved Driver including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single

core cable and earthing etc as required.

6 WIRING FOR DATA AND VOICE OUTLETS - -

Supply and fixing the following sizes of PVC medium duty ISI marked conduits (IS : 9537 Part-III)

complete with accessories such as bends, junction boxes, pull boxes etc., in recess or on surface

including cutting chases in the walls/floors and making good the same complete as required.

Digitally signed by AMIT

DSR-2022 Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

Supplying and drawing of CAT 6A U/UTP cable, white jacket, 4 pair LAN Cable in the existing surface/

6.2 1.53 recessed Steel/ PVC conduit as required. - -

Supply & fixing of Plug in type information outlet (campatible with data cables) in existing faceplate/

6.3 MR GI Box in wall/furniture/floor complete as required. Nos. 482.51 60.00 28,950.56

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box

6.4 1.24 including connections but excluding modular plate etc. as required. - -

1.24.6 Telephone socket outlet Each 148.00 40.00 5,920.00

6.5 Supply and fixing of the following types Face Plates complete with all accessories. - -

Supply & Fixing of Dual Faceplate, Duplex Port (for data and for voice) or as required square plate

a. MR having spring shuttered front access for preventing ingress of dust, dimension as per commercially Nos. 90.04 40.00 3,601.58

available modular office furniture.

Supply ,laying ,installing , testing and commmissioning of the 50 pair multi core 0.61 mm annealed

copper conductor PVC insulated and PVC sheathed armoured telephone cables generally

6.6 MR conforming to ITD S/WS-11-C and IS 1554 part I direct in ground /surface and / or in existing pipe as mtr. 380.57 50.00 19,028.28

required and includig making terminal joints, complete as required.

Supplying, installing, testing and commissioning of 24 port Cat 6A patch panels available with block of

four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6A U/UTP 24 port

LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less connector U/UTP unit in a block

with wall mounted Rack

7 CABLE TRAY.& RACE WAY. - -

7.2 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only) - -

MR Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with internal

partition/compartmentized of the following sizes including providing removable 3 mm thick GI cover,

knock out holes and fixing accessories earthing with 8 SWG copper earth wire complete as required - -

including floor supports, bends, access boxes, tap off boxes and cross over as per specification and

site requirement. (overhead / wall mounted recovery & function boxes shall be 1.6 mm thick)

c) MR 150 mm wide x 38 mm deep raceway or as per site RM 1,503.10 10.00 15,031.00

d) MR 100 mm wide x 38 mm deep raceway or as per site RM 1,150.00 10.00 11,500.00

MR Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet junction box including providing 3

mm thick stainless steel cover as per specification.

A. FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) - -

a) 17.1.1 Supplying, installation, testing & commissioning of heat detector operating at 542C/572C with rate of No.

rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection 1,071.00 1.00

etc. as required.

b) 17.1.2 Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base No.

complete with all connections etc. as required. 1,153.00 10.00

Digitally signed by AMIT

DSR-2022 Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

d) 17.1.4 Supplying, installation, testing & commissioning of manual call box of ABS type in surface/recess with No.

stainless steel chain & hammer assembly complete with glass and push button etc. as required. 408.00 1.00

e) 17.1.5 Supplying, installation, testing & commissioning response indicator on surface/recess MS box having No.

two LEDs metallic cover complete with all connections etc. as required.

g) 17.1.7 Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, No.

mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching 491.00 1.00

transformer etc. complete as required.

i) Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with

visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities

as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections,

interconnections as required.

B CABLES & ACCESSORIES FOR FAS : - -

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, RM

600/1000V rated with annealed copper conductor having

XLPE insulation, steel wire armouring & FRLS outer sheath

complete as required.

C SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES : - -

Total DSR & Total Non DSR 6,41,728.00 2,77,602.42

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/ Variable Refrigerant Volume air cooled Outdoor units suitable for cooling

and heating, having all hermetically sealed inverter type Scroll Compressor(s),

minimum two compressors for above 14 HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R410A Refrigerant,

1.0 1.1 vibration isolators, with suitable foundation etc. complete as required.The unit Per HP 16415 20.00 3,28,300.00

shall deliver the rated capacity at AHRI Conditions and work even at 50°C

ambient temperature without tripping.The unit shall be suitable to work on 400V+/-

10%, 3 Phase, 50Hz AC power supply.The unit shall be filled with first charge of the

refrigerant and ready for use as required.The COP at AHRI conditions shall not be

less than 3.1 and IEER not less than 6.5 .

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following minimum capacity 4-

wayflow VRV/ VRF Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre-filter, fan section with low noise fan/ dynamically

balanced blower, multi speed motor, coil section with DX Copper coil, electronic

expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

isolation, cordless remote control etc., suitable for operation on single phase

230V±10%, 50 HzAC supply, complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from BMS System. The

cooling capacity of indoor unit will be at air inl et conditions of 27 Degree CD

Band 19 Degree CWB temperature.

4-Way Cassette type - -

3.0 REFRIGERANT PIPING - -

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

Supply, Installation, testing and commissioning including vaccumiazation and

Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant

DSR 2019 piping for VRV/VRF system, complete with fittings, with suitable adjustable ring

3.0 VRF/VRV type hanger supports, jointing/brazing including accessories, insulated with XPLE - -

Item No 5 Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber

tubular sleeves sections of specified thickness as given below for Suction and

Liquid lines, all accessories as per specifications etc. as required :

3.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 331.0 60.00 19,860.00

3.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 466.0 40.00 18,640.00

3.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 588.0 90.00 52,920.00

3.5 5.5 19.2 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 707.0 40.00 28,280.00

3.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 865.0 40.00 34,600.00

3.8 5.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation Rmt 1230.0 30.00 36,900.00

4 CONDENSATE DRAIN UPVC PIPE - -

Supply, installation, testing and commissioning of uPVC Pipe ,complete with fittings, supports,U

trap arrangement,Clean Plug with 6mm nitrile insulation and accessories as per specifications, - -

4.3 MR Imported fittings Y-joints and headers etc. Nos 3281.4 8.00 26,251.26

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper in suitable

conduits between indoor and outdoor unit.

MR Supply and fixing IP-55 based outdoor MCB box with 1 NOS 65 amp RCCB Nos 12650.0 1.00 12,650.00

MR Supply and fixing MS base frame for VRV outdoor stand as per approved size NOS 4500.0 1.00 4,500.00

Supply installation testing and commissioning Treated Fresh Air HRV capacity 800 CFM for Fresh Air

Ventilation as per approved make

2 MR-2 Providing and fixing of 24 gaze GI Ducting rectangular as per required SQFT 330.00 240.00 79,200.00

3 MR-3 Providing and fixing of Aluminium flexible Duct NOS 6,844.00 5.00 34,220.00

4 MR-4 Providing and fixing powder coted louver and birdscreen for fresh air wall opening LOT 19,500.00 1.00 19,500.00

5 MR-5 Providing and fixing of canvas connection NOS 8,210.00 1.00 8,210.00

6 MR-6 Providing and fixing Grill of required size NOS 2,200.00 8.00 17,600.00

Digitally signed by AMIT

Sr. No. Item Description Unit Rate Qty Amount

1 Supply, Installation, Testing & Commissioning of 24 PORT Managed Network Switch Unit 42,650.00 1 42,650.00

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265 Vandal Proof Dome camera with 2.8 to 12mm Motorized

Lens,Smart IR, up to 30M IR distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise Reduction),H.265+,

H.265, H.264, MJPEG,Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux

with IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Crossing line, Motion detection,

1 Object left, Missing object,Intelligent Identification Face detection, Defocus, Scene Change,PoE (IEEE802.3 af) Power Nos 7,500.00 8 60,000.00

consumption: Max 7.2W,Edge Storage Micro SD Card, Up to 256GB, ANR Support,Working Environment -40°C ~ +60°C,

Humidity ≤ 90% RH(Non-condensing),Compatible Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing and Commissioning of 16Ch Embedded Network Video Recorder with 4 Sata Supports 1 × RJ45

2 1000M ,4K Cameras, HDMI, VGA, RAID, Redundant power supply, Smart Analytics and ONVIF, including wall mounted rack Nos 65,320.00 1 65,320.00

3 SITC of SSD Hard Disk Drive 8TB, 24/7 surveillance category Only complete etc as required.etc.all complete. Nos 29,500.00 1 29,500.00

C. 20 Pair MDF Box -

1 20 Pair MDF Box with mounting Frame 5,500.00 1 5,500.00

Digitally signed by AMIT

Specifications Rate Qty Amount

DGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and

non working edges shall be finished with machine pressed with 2mm PVC egdge banding. The

table top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three

1 equal drawer unit and two openable shutter & one open storage with shelf in it. The Side unit 55,803 1.00 55,802.50

top shall be made out of 18mm thick pre laminated particle board and rest all storage to be

made out of 18mm thick pre laminated particle board. Provision of Junction box, wire raceway

and 6 module fliptop box for wire passing or as per site requirement.Main Table Dimension

(L)1800mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X

DGM High Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-

Back Chair (W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design

contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and

back) upholstered with leatheritte and cut foam. The chrome plated loop armrest with padded

2 upholstery is provided for extra comfort. The chair shall be provided with pneumatic height 22,185 1.00 22,185.00

adjustment which shall have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/-

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

DGM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X

Back Chair (D)505mm X (H)990mm.A contemporary design with an all black finish, . Material &

subtype:Premium Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm

X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever, Maximum

3 Seating Height:19".The Seat & back are made up of 12mm thk hot pressed plywood upholstered 17,640 3.00 52,920.00

with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest

has a foam of 28kg/m3.

Digitally signed by AMIT

Specifications Rate Qty Amount

2/1 seater Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to

sofa the soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour &

Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech

solid wood have used for framing construction of sofa .The seat cushion is made of multi

4 layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 38,250 3.00 1,14,750.00

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch

strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2

seater Dimension(L)1390mm X (D)750mm X (H)710mm

AGM AND Supplying and placing in position of main table as per photograph/drawing .The table shall be

BMO Table made out of 25mm thick pre -laminated particle board of approved shade. The working and

non working edges shall be finished with machine pressed with 2mm PVC egdge banding. The

table top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three

equal drawer unit and two openable shutter & one open storage with shelf in it. The Side unit

5 top shall be made out of 18mm thick pre laminated particle board and rest all storage to be 50,085 2.00 1,00,170.00

made out of 18mm thick pre laminated particle board. Provision of Junction box, wire raceway

and 6 module fliptop box for wire passing or as per site requirement. Main Table Dimension

(L)1800mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X

AGM High Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

Back Chair 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof

plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood

(IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be

provided with self tension single locking mechanism and pneumatic height adjustment which

shall have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height adjustment shall have

6 adjustment stroke of 100 mm and shall be operated at 30kgs extension force.The Seat & back 20,322 2.00 40,644.00

are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam,

chair seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable

arm rest and head rest

Digitally signed by AMIT

Specifications Rate Qty Amount

Conference Supplying and placing in position of conference table of required size as per image/drawing.

Table The work surface top should be of thickness 42mm top prelaminated particle board with 2mm

thick PVC edge banding. The side panel are made up of 36mm thick prelaminated particle &

modesty panel are made out of 25mm thick prelaminated particle board with 2mm thick PVC

7 edge banding. The wire carrier should be made from 0.6mm thick CRCA & powder coated 40- 85,500 1.00 85,500.00

50 microns. Also having a provision of 6 module flip top box & metal raceway for wire flow.

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair

chair of Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically

design contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat

and back) upholstered with leatheritte and cut foam. The chair shall be provided with

8 pneumatic height adjustment which shall have stroke of 10.0 +/- 14,850 35.00 5,19,750.00

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg

/m3) The backrest has a foam of 28kg/m3.

Modular Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side

Workstation Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht.

1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side

laminated and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end

9 18mm thick MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H 29,385 8.00 2,35,080.00

made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For

drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-Munshel Gray. and

White Tinted Glass

lenior Dimesnion: 1200mm(L)x 600mm(D) x 750mm(H) Modular Workstation With 1200mm, Double

Workstation Raceway systems Skirting label and below the table top . lower tile both side laminated and

upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end

10 18mm thick MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H 23,850 8.00 1,90,800.00

made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For

drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-Munshel Gray. and

White Tinted Glass

Digitally signed by AMIT

Specifications Rate Qty Amount

Reception Supplying and placing in position of main table as per photograph/drawing .The table shall be

Table made out of 25mm thick pre -laminated particle board of approved shade. The working and

non working edges shall be finished with machine pressed with 2mm PVC egdge banding. The

table top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three

11 equal drawer unit and two openable shutter & one open storage with shelf in it. The Side unit 34,740 1.00 34,740.00

top shall be made out of 18mm thick pre laminated particle board and rest all storage to be

made out of 18mm thick pre laminated particle board. Provision of Junction box, wire raceway

and 6 module fliptop box for wire passing or as per site requirement. Main Table Dimension

(L)1350mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)1200mm X (D) 450mm X

Pantry Table Providing & Installation of Pantry table of size 1.2m x .9m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per

design. The Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to

be provided above table. One (1) number Drawer pedestal with 3 drawers to be provided

under the table.

Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC

14 SIDE TABLE WITH WOODEN STRUCTURE 11,250.00 1.00 11,250.00

Openable The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel

Shutter is made of 09mm thick MDF of approved shade. All the edges of storage surface shall be

storage provided with machine pressed imported PVC lipping glued with hot melt EVA glue free from

any VOC with free groove handle and suitable lock. All exposed area PVC edge lipping

Total Amount 17,10,056.50

Total Amount 17,10,056.50

Digitally signed by AMIT