SPL REPAIRS ADDL ALTN AND IMPROVEMENTS TO CERTAIN BUILDINGS AT AF STN SAMANA UNDER GE (AF) JAMNAGAR NO 1

Amount

M&L for complete removal of existing treatment of any thickness laid over RCC roof / chajja, cleaning and washing of roof / chhajja with water to remove dust etc as preparation to receive treatment, brooming down or steel wire brushing, scraping down smoke soot, mouls, moss and efflorescent salts and treating oil and greasy spots complete all as specified and directed

M&L for brushing neat cement slurry with 3.0kg of cement per square metre complete all as specified and directed.

M&L for cement concrete in roof pading, coving, filling and mass concrete type B-0, 1:2;4 (using 12.5mm graded stone aggregate) complete all as specified and directed

M&L for screed bed 10mm thick on concrete surface in CM 1:4, finishing the surface even and smooth without using extra cement, including mixing only liquid water proofing compound as per manufacture instruction complete all as specified and directed Note : liquid water proofing compound will be measured & paid separately.

Supply only integral water proofing chemical @ 200ml/Bag of cement complete all as specified and directed. Make : Fosroc, Dr Fixit or equivalent as specified.

M&L for water proofing treatment to RCC roof slab all as specified below and as directed:- (a) Apply one coat of glass fibre base bitumen felt primer, grade 2 @ 0.25 Kg/Sqm. (b) Laying APP based ploymeric membrane 3mm thick, minimum wt 3.00 kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150gms/Sqm ) laid on primed roofs & flashing by forced application having side overlap 100mm and at the end 150mm using Butane torch, and sealing all joints and overlaps

Dismentling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F 600x600mmx4mm thick false ceiling of non asbetos fibre cement building boards (E Board) and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25mm x 25mm x 1.5mm thick in squre pattern of grid size 605 x 605mm. The aluminum work will be suppoted on side wall with the use of aluminium 'L' section of size 25mm x25mm x1.5mm angles etc. Snap grid shall be supported with hangers of 4mm dia galvanised iron wire adjusting level fixed to roof slab/truss etc by means of ceiling cleats made out of galvanised iron flat of size 40x3mm size 60mm long and expansion hold fastners 12.5 mm dia 40mm long complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise specifically provided for complete all as specified & directed.

S&F for Framed work such as Chhaja frame , grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks , and similar work con- forming to Fe.290.Gde-E-165

M&L for preparation of new steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old painted steel surfaces over 10 cm in width or girth and applying one coat of synthetic enamel paint

M&L for preparation of old painted wooden surfaces, exc 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed by Engineer-In-Charge.

Taking down chowkats or frame with shutter of any description (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site complete all as specified and directed Engineer-in-Charge

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters of any description (W/out taking off shutters from the frames) and removal from site complete all as specified and directed Engineer-in-Charge

Taking down shutter any description area exc 1 Sqm but n.exc 2 Sqm each, complete all as specified and directed

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including 0.9mm thickness decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as directed.

S&F for powder coated Anodised aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F for powder coated aluminium sections (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ handles/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. ( Note - Weight of aluminium sections and fittings / fixtures of aluminium shall be measured and paid for under this item. Quoted Rrtes are deemed to be inclusive of EPDM / rubber / neoprene gasket and fittings / fixtures other tahn aluminium)

S&F for sheet glass 4mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane

M&L for 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & fixed with aluminium frame work

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

M&L 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

S&F for Door closer die cast hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

S&F for brass 4 lever mortice lock, vertical type, size 100 mm brass 4 lever complete all as specified& directed

S&F for 200mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified & directed.

S&F 125 mm in size aluminium handles cast type anodized complete all as specified & directed.

S&F 300 mm long aluminium alloy anodized sliding door bolts with hasp and staple (bolt type and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy) complete all as specified & directed.

S&F for over all length of cover length 140mm, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

Demolition of brick /stone /PCC block masonary in cement mortal including all quoins, pillars, arches etc. complete all as specified and as directed.

M&L for providing precast cement concrete (1:5:8) (using 20mm graded stone aggregate) solid building blocks exc 10 cm thick, in width (with plain or inter locking joints as directed) setting in CM 1:6 complete in wall or pillars all as specified and directed.

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for, including removing excavated/ demolished material outside MD land, all as specified and as directed.

Demolition of cement concrete in ground floor and pavings not exc 15cm thickness below or above ground level, including removal excavated / demolished material outside MD land.

M&L for 75 mm thick Cement concrete type C- 2, 1:3:6 (40mm graded aggregate) as plinth protection/hardstanding etc complete all as specified and as directed

M&L for hardcore broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in sub base of flooring, finish the surface fair & even and fair all as specified & directed.

M&L for Rubber moulded chequered cement concrete tile with white cement and pigment (of approved tint) of size 30 cm x 30 cm x 25 mm thick , set, jointed and pointed in neat cement slurry complete.

Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to a distance exc 1.5 km but n.exc 2 Km complete all as spd and directed.

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as spd and directed

M&L for light shade virified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all specified and as directed.

M&L for 2mm thick linoleum, plain coloured, laid on floors, linoleum is sealed down with an approved adhesive including stretching, cutting and fitting, cplete all as specified and directed.

M&L Green Marble work 15 to 18 mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as spd and directed

Dismantling and disconnecting of existing cast iron or reinforced concrete drain pipes, jointed in cement mortar 75/100 mm dia bore fixed to wall,laid in trenches complete all as specified and directed Engineer-in-Charge

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed on walls including clamp complete all as specified and directed

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed

S & F 110 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes in repair complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries outside MD land, complete all as specified and directed

M&L for rendering 15 mm thick on stone masonary/brick / concrete surface of walls in cement mortar 1:4 finished even & smooth without extra cement complete all as specified and directed Note- WPC will be measured and paid separately

M&L for rendering 15 mm thick on stone masonary/brick / concrete surface of walls in cement mortar 1:6 finished even & smooth complete all as spd and directed Note:- Quoted rate deemed to carryout wk at height upto 5.00 m

M&L for rendering 10 mm thick in patches on fair faces of brick or concrete surfaces in CM 1:3 as on ceiling, facia roof projection etc finished even and smooth as directed by Engineer-in-Charge.

M&L for Preparation of old distempered / decorated surfaces of ceiling, washing, rubbing down and stopping of distempered and painted surfaces and applying Two coat of Distemper oil emulsion complete as specified and directed.

S&F in repair Curtain rod, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified & directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

S&F anodised aluminium three track podwer coated of any colour (thickness of powder coating not less than 50 micron) sliding window with three sliding shutter, the size of outer frame three track 92 x 31.5 x1.20mm ( using two track for glazed window shutter and one track for wire gauged ), the section shutter size 37x18x1.2mm) and glazing with 4mm thick glass (plain/floated) including all around suitable rubber gasket and MS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminium flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2numbers slidings rollers of nylon with including all necessary fittings comlete all as specified and directed.

S&F for sheet glass 4mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

S&F for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

M&L Rendering 10mm thick in CM 1:4 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing for skirting/dado etc complete all as spd and directed

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as spd and directed

M&L for Non skid, coloured ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc laid over and pointed with coloured cement to match the tiles complete all as spd and directed

Dismantling water tanks exc 250 & n exc 500 and removing to store complete all as specified and as directed.

S&F 500 litres capacity triple layer, any coloured rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc complete.

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Cutting chases, pinning in, making good to facings on stone concrete, block or slab wall, where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as spd and directed

S&F 20mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

S&F 32mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

S&F in repair 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S&F CPVC ball valve for 32mm outer dia pipe complete all as specified.

S&F in repair vitreous china wash basin, white, flat back, size 550 mm x 400 mm fixed on and including cast iron cantilever bracket 32 mm dia brass waste coupling, waste pipe and including waste fitting and union complete all as specified and directed by Engineer-in-Charge

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white with CI 'P' or 'S' trap incl water closet seat cover of plastic,jet etc.complete incl necessary PVC waste pipe fitting, complete all as specified and directed by Engineer-in-Charge

S&F 10 Litre capacity PVC symphonic action type flushing cistern, duel flush type (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting complete.

S&F in repair 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as spd and directed

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as spd and directed

S&F in repair 15mm dia size Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as spd and directed

S&F 15mm size angular Stop valves but fancy type, chromium plated , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as spd and directed

S & F in repair Tubular towel rail, 20mm dia, D type, 600mm long between flanges chromium plated complete all as spd and directed

S&F in repair chromium plated soap tray any type and fixed to plugs on wall with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge

M&L for 75 mm dia of PVC (SWR) floor trap plain with grating incluing jointing with solvent cement , in repairs, complete all as specified and directed by Engineer-in-Charge

S&F for PVC (SWR) 75mm pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed.

S & F 75 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes provided in repair complete all as specified and directed by Engineer-in-Charge

S & F 110 mm bore of pipe PVC (SWR) junction single,(Single T) equal or unequal fixed to PVC pipes with access door in repair complete all as specified and directed by Engineer-in-Charge

S & F 110 mm bore of pipe PVC vent cowl fixed to PVC pipes in repair complete all as specified and directed by Engineer-in-Charge

Dismantling mild steel rolling shutter of any description not otherwise specifically provided for complete all as specified & directed.

S&F 1.25mm thick steel rolling shutters, with ball bearing, including top cover, safety lever locks mild steel with 4 levers for rolling shutters as specified, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: push pull or manual type

Finishing to kota stone flooring jointed with grey cement slurry mixed with pigment to match the shade of the floor inluding rubbing and polishing complete all as specified and directed.

M&L for rendering in cement mortar (1:4), 10mm thick as dubbing out coat on brick work other than fair face or on cement concrete surface including 10mm thick floating coat in CM (1:3) over dubbing out coat mixed with water proffing compound finished even and smooth.complete all as specified and directed Note :- water proofing compound will be measured and paid separately.

S&F welded steel wire fabric wt n. exc. 4 kg per sqm supplied and fixed complete to wood or steel members, conrete/ stone wall surface complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces walls/fins/facia/soffit etc complete all as specified and directed Note:- Quoted rate deemed to carryout wk at height upto 5.00 m

M&L for preparation of newly plastered wall surface and applying 2mm thick wall care putty for making smooth surface and applying two coat distemper oil emulsion complete all as specified. Note:- Quoted rate deemed to carryout wk at height upto 5.00 m

M&L for preparation of newly plastered ceiling surface and applying 2mm thick wall care putty for making smooth surface and applying two coat distemper oil emulsion over a coat of alkali resistant primer complete all as specified. Note:- Quoted rate deemed to carryout wk at height upto 5.00 m

Taking down carefully any aluminum /copper point wiring (light,fan,socket or power) complete including conduits/casing caping with f the materials/debris and making good the disturbed surface of walls & floors etc to match with the original existing finish complete all as specified and as directed.

Taking down carefully any aluminum /copper point wiring (light,fan,socket or power) complete including conduits/casing caping including fixture and fittings such as switches,ceiling rose pendants,regulator sockets light fittings etc removing material/debris for taking credit and making good the disturbed surface of walls & floors etc to match with the original existing finish complete all as specified and as directed.

Taking down sub main wiring of three core PVC cable PVC insulated 2.5 Sqmm / 4 Sqmm / 6 sqmm / 10 Sqmm including casing & caping or wooden batten and remove from the site of work and making good the disturbed surfaces of wall or floor etc. as directed and specified by Engineer-in-Charge.

Taking down carefully by unscrewing from fitting and fixtures as switches,ceiling roses, pendents,regulators,bells, sockets, tube light fittings,DB,MCB etc, for reuse at site or carrying to the store( To be found measured only when found serviceable in all rspect for reuse) and refixing the same all as specified and as directed

Material & Labour for point wiring with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn and including PVC casing capingor conduit not less than 25mm Diaor width, including all accessories like bend, tees, junction boxes etc. including 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable as a earth wire connected to common earth dolly, etc excluding sheet metal flush box suitable for modular switches complete for following:

One Light point/ fan / exshaust fan point controlled by one switch

One 3 pin socket out let 5 Amps on the independent board.

All as per item No.97 above but with 4.0 sqmm multistranded copper multistranded conductor FRLS cable with 4 sqmm earth wire for one 6 pin socket outlet 15 Amps on independent board

S & F in repair switch 6 Amps flush button type, SP, one way, 230 Volts, AC

S & F switch 6 Amps , flush button type, SP, one way, 230 Volts, AC

S & F switch socket combination 6 Amps , flush type 2 in 1, 230 / 250 volts , AC with ISI marked

S & F switch socket combination 16 Amps 3 pin, flush type, multipurpose, 230 / 250 volts , AC with ISI marked

M & L ceiling rose polycarbonate body 6 Amps, 250 volts AC three Terminals complete all as specified.

S & F in repair switch socket combination 6Amps , flush type, multipurpose, 230 / 250 volts , AC with ISI marked

S & F in repair switch socket combination16 Amps , flush type, multipurpose, 230 / 250 volts , AC with ISI marked

M & L in repair ceiling rose polycarbonate body 6 Amps, 250 volts AC three Terminals complete all as specified.

Supply and fix in repair sheet metal enclosure MCB DB, triple pole and neutral,8 ways double door 415 volts having 200 Amps double door rated bus bar with blanking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fix in repair sheet metal enclosure MCB DB, single pole and neutral, 8 ways double door 240 volts having 200 Amps rated bus bar with balnking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fix in repair sheet metal enclosure MCB DB, single pole and neutral, 12 ways double door 240 volts having 200 Amps rated bus bar with balnking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fix in repair sheet metal enclosure MCB DB, triple pole and neutral,6 ways double door 415 volts having 200 Amps double door rated bus bar with blanking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fixing repair MCB single pole 240 volts 6 to 32 Amps (to be fixed as per load requirement) 220V with 'C' curve complete as including all connectionsas directed by engineer in charge

Supply and fix in repair MCB Single pole Neutral 240 volts 40- 63 Amps (to be fixed as per load requirement) 220V with 'C' curve complete as including all connectionsas directed by engineer in charge

Supply and fix in repair MCB’s triple pole & neutral, 63 Amps, 415 volts with ‘C’ curve, fixed in sheet metal board complete including connecting items as directed by engineer in charge

Supply & Fix energy efficient LED tube light fitting with built in LED & integral LED driver 20 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge

Supply & Fix energy efficient LED tube light fitting with built in LED & integral LED drive 10 watt, channel housing & diffuser of length 800 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

Supply and fix Energy Efficient recessed mounted LED luminarie 600x600 false celing light 36 watt complete including connection. Make Phillips complete or equivalent in Wipro/Crompton

Supply and fix Industrial Exhaust Fan 230V Single Pole 450 mm 1400 RPM sweep with louvers metal body fixed as per manufacturer instruction connecting with and including 1.5 Sqmm copper conductor,PVC insulated and PVC seathed 3 core cable including making suitable size hole in brick/PCC block masonary wall built in CM and making good disturbed surface complete. Make: Havells or equivalent of make Bajaj/crompton/usha.

Supply and fix Exhaust Fan 230V Single Pole 250 mm 1400 RPM sweep with louvers plasticl body fixed as per manufacturer instruction connecting with and including 1.5 Sqmm copper conductor,PVC insulated and PVC seathed 3 core cable including making suitable size hole in brick/PCC block masonary wall built in CM and making good disturbed surface complete. Make: Havells or equivalent of make Bajaj/crompton/usha.

Supply & Fix energy in repair efficient LED tube light fitting with built in LED & integral LED drive10 watt, channel housing & diffuser of length 800 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

Supply and fix in repair Energy Efficient recessed mounted LED luminarie of 35/36 wat 600x600mm false celing light complete including connection. Make Phillips complete or equivalent in Wipro/Crompton

M&L for sub main wiring with four runs (3 Phase + 1 Neutral) of single core PVC casing caping fixed unsheathed 1100V grade multistranded copper conductor cable 10 Sqmm size inclusive fixed in wall incl two runs of 6 Sqmm PVC insulated unsheathed copper conductor cable as earth wire complete all as specified and as directed.

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLS type cable drawn through and including casing and caping com including PVC casing caping not less then 25 mm wide with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire and connecting to tbe BD with proper size of lugs/thimbles etc comnplete all as specified and directed.

Material & Labour for sub main wiring with 2 run single core multistranded copper conductor cable, of size 4 Sqmm, PVC insulated, unsheathed, fire retardant low smoke, drawn through and including PVC casing caping not less then 25 mm wide with all necessary fitting and including one run single core multistranded copper conductor cable, of size 4Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling, complete all as specified and directed.

Taking down and re- fixing , testing fire alarm system with , smoke detector, heat detector, alarm, manual call point ,conventional sounder, Response indicators with its wiring and acessories and necessary connections complete in working condition

Material and labour in replacement for provision of earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to galvanised earth lead 4mm dia by means of bolts, nuts, check nuts and washer of galvanized steel, watering pipe of 20 mm bore galvanised iron medium grade and 40 mm bore galvanised iron light grade for earth strip protection including.....

S&F in repair LED building security light fitting 35 Watt, system efficiency not less than 100 lumen / Watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment , Heat resistance toughened glass fitted in cast aluminium housing with SS screws, pipe, bracket on building,

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 2.50 sqmm with multi stranded copper conductor , FRLS type cable drawn through and including PVC conduit 25 mm complete with all accessories along with provn of 2.50 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire and connecting to tbe BD with proper size of lugs/thimbles etc comnplete all as specified and directed.

Taking down Existing AC with Indoor and outdoor units and deposit to store safely and refixing it with making suitable hole in wall for outdoor pipe and wire and making the surface good as specified and directed by engineer in charge.

Taking down and refixing wall mounted fans of any type on wall as specified and directed by engineer in charge.

Supply and fix in repair Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of rating 20 amps.

Taking down Ceilling fan/exhaust fan with cover plate , sealing cable end, dismantling blades and removing fan and blad for painting of ceiling fan/Exhaust fan complete with synthetic enamel paint black/ white by spraying including filling of cavities with filler, one coat after cleaning all rust and dust etc complete and refixing the same with 0.5 sqmm , flexible ,three core wire, copper conductor cable all as directed by Engineer-In-Charge. all as specified and directed.

supply and fix wall mounted fans 400 mm sweep 1400 RPM 100% copper motor winding on wall as per manufacturer instruction connecting with and including 1.5 Sqmm copper conductor,PVC insulated and PVC seathed 3 core cableas specified and directed by engineer in charge Make Havells platina or equivalent

Supply and fix in repair triple pole and neutral enclosure with a two pin and earth plug and socket complete with one three pole MCB of rating 32 amps.

Supply and fixing, wall mounting fans 230Volts single phase 600mm sweep, 1440 rpm ,5mfd capacitorhigh performance motor, with Metal, jerk free oscillation, aerodynamically designed & balanced blade including grouting on wall with fastners & provision of 1.0 Sqmm copper conductor of three core flesible cable from fan to connector/ceiling rose complete all as specified and directed. Make -Model No Airboll HS speed of Havells or equivalent Model of Crompton vortex Make Havells equvellent of Make Bajaj, Crompton, Usha

Supply and fix ceiling fan five star rated of 1200 mm sweep compete with blades, down rod conopy electronic type regulator etc including hanging in position and connecting with 3 core, 0.50 Sqmm copper conductor PVC insulated and PVC sheathed round cable from ceiling rose to fan complete all as specified and directed by Engg -in-Charge. Make Havells equvellent of Make Bajaj, Crompton, Usha

Sagathiya Builders (BID ID -3131663)

Jagdamba Engineering (BID ID -3137583)