PROVISION WORK OF GUARD ROOM OPEN SHED MT SHED AND CONNECTED WORKS ETC AT BINNAGURI MIL STN UNDER GE (N) BINNAGURI

Amount

Schedule 'A'

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out in Soft/loose soil complete all as specified and directed.

Returning filling in including spreading leveling watering and well ramming in layers n exc 25cm thick in soft/loose soil complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

M&L for earth filling under floors in layers n.exc 15cm thick,spread,levelled and rammed including watering complete all as specified and directed by Engr-In-Charge.

M&L for hard core of gauge n.exc 63 mm and deposited spread and levelled in layers n. exc 15 cm thick , watered and rolled / rammed to a true surface with broken stone or boulders complete all as specified and directed by Engr-In-Charge.

M&L for cement concreteType C2, 1:3:6 (40 mm graded aggregate) in foundations, filling and mass-concrete complete all as specified and directed.

M&L for RCC design mix M-25 with using 20mm graded aggregate as in foundation, footing, plinth beam under ramed pile bases for column etc complete all as specified and directed by Engr-In-Charge.

M&L for RCC design mix M-25 with using 20mm graded aggregateas in colums, posts and struts complete all as specified and directed.

Supply only integral water proofing compound of approved quality ISI marked complete all as specified and as directed.

M&L for brickwork with flyash bricks straight or curved on plan exc 6 m mean radius old size bricks built in Cement mortar 1:6, using old size brick complete all as specified and directed.

M&L for formwork to sides of concrete foundations rough finished surfaces of concrete, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc flat rough finished surface complete all as specified and directed by Engr-In-Charge.

S&F for 35mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and conforming to IS-2022-1993 (Part-I) and ISI Marked complete all as specified and directed by Engineer-in-charge.

S&F Factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail, MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; Panelling of plain colur PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, in the frame at site as per specification and drawings complete all as specified and directed.

All as per item No 14.00 here-in-above but partly glazed i.e. upper panel will be wire mesh fitted externally in the clear space & lower panel will be plain colour PVC sheet

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19x19mm MS square tube and 1.2mm wall thickness complete all as specified and as directed.

S&F of 150 mm length aluminium anodised, barrel tower bolts of extruded section (dia of bolt 12mm) and fixed complete all as specified and directed by Engr-In-Charge.

S&F 300 mm length of bolt aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-In-Charge.

S&F 75mm stainless steel butt hinges,anodised and fixed type C-21 complete all as specified and directed by Engr-In-Charge.

S&F of aluminium handles, cast type anodised of 125 mm size. complete all as specified and directed by Engr-In-Charge.

S&F for brass chromium plated tubular towel rail, 20 mm dia, D type 60 cm long between flange complete all as specified and directed by Engr-In-Charge.

S&F of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-In-Charge.

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engr-In-Charge.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-In-Charge.

All as per item No 24.00 here-in-above but 8mm dia and over TMT bars upto and including 10mm dia in stirrups, spacers and binders and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-In-Charge

M&L for mild steel structural members i.e. angle iron Tee etc cut to length and shape welded as in bracing conforming to Fe-410 W(Gde E 2500, quality A) complete all as specified and as directed.

M & L for framed work as in doors frame of angle or other section conforming to Fe 410-W(Gde-E- 250)quality-A with gusset plates, rails, braces, etc., and including fixing of steel hinges or other door fittings complete all as specified and directed. (door fittings like hinges, tower bolt etc shall be measured and paid seperately)

S&F factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded confirming to IS 1038-1998 complete all as specified and directed by Engr-In-Charge.

S&F factory made in repair steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay,complete without glazing bars, dovetailed or welded confirming to IS 1038 complete as specified and as directed.

S&F factory made steel ventilator with top hung shutter including box type hinges, peg stay confirming to IS 1038 specifications all complete as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified.

M&L 75mm thick PCC (1:3:6) type C2 using 40mm graded aggregate as in plinth protection/footpath, floors,sub base and to receive top layer or tiling using 40mm graded stone aggregate, finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for providing 75 mm thick cement concrete type D-2, 1:4:8 using 40 mm graded aggregate as in sub base of floor finished rough to receive floor topping including 150 micron polythelene sheet with laping over sand filling complete all as directed.

M&L for 25mm thick PCC (1:2:4) type B-0 with using 12.50 mm graded stone aggregates as in flooring, finished even and rough to receive the top layers all complete as specified and as directed.

M&L for 300 x 450mm glazed ceramic coloured tiles in vertical surface not less than 6 to 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with including providing 10mm thick rendering in CM 1:3 complete all as specified and as directed.

M & L Non - skid Ceramic tiles(colour) 6 to 7 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L 25 mm thick pre-polished coloured chequred smooth finish exterior grade precast heavy duty shine finish paver tiles as approved set & jionted and pointed with grey cement and pigment complete all as spd and as directed.

M & L Machine cut kota stone slab in flooring 18-20 mm thick including 20mm thick cement mortar screed bed(1:6)CM laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete all as specified and as directed.

M&L for kota stone slab 18-20 mm thick in riser or steps, skirting, dado and pillar including 10 mm thick rendering in CM (1:3) CM laid over and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for rendering 15 mm thk (1:6) on fair faces of brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 20mm thick plaster of cement mortar (1:4) on fair faces of brick work in two layers (10mm thick each) mixed with water proofing compound in top layer as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed. Note : Integral water proofing compund shall be measured and paid separtely.

M&L for RCC M-25 Design Mix as in chajjas roof projection sun shed etc complete all as specified and as directed.

M&L for form work rough finished surface as in chajja, chullah hood etc complete all as specified and as directed

M&L for three coats of white washing on walls including preparing new plastered surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for two coats of colour wash on new plastered surfaces incl preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Supply & fixing of sheet glass 3mm thick , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing of figured glass 3mm thick, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coats of pink primer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coats of red oxide primer complete all as specified and directed by Engineer-in-charge.

S & F 15mm bore medium grade galvanised tube ISI marked with all fittings and fixed complete to walls and ceilings or laid in floors.

S & F 20mm bore medium grade galvanised tube ISI marked with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F 75 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 kgf/Sqcm fixed complete to floors, wall, ceilings etc. complete all as specified and as directed.

Suppy, hoisting and fixing of Rotational moulded PVC water storage tank, 1000 liters capacity ISI marked cylindrical vertical type multy layered with closed top including inlet, and necessary fittings outlet and wash out holes complete all as specified and as directed

S&F CP bib taps cast copper alloy with crutch or butterfly handle screwed for iron piipe or for brass ferrule of 15mm dia complete all as specified and directed.

S&F pillar taps, cast copper alloy, with heads, chromium plated, screwed down high pressure with or without lettered 'hot or cold' with long screwed shanks and flynuts screwed for iron pipe and fixed for 15mm.(complete all as specified and directed.

S&F CP angular stop valves cast copper alloy screwed down high pressure with crutch handle screwed both ends for iron pipes or for unions and fixed of 15mm dia. complete all as specified and directed.

S&F of 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed as required to use reduser and check nut etc complete all as specified and as directed.

S&F of PVC (SWR) nahani trap, plain with grating including jointing with solvent cement outer dia 75 mm cement concrete (1:2:4), type B1 including complete all as specified and as directed.

S&F of shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Min weight 300 gms ) complete all as specified and as directed by Engineer-in-chargecomplete all as specified and directed.

S&F Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe)includingUrinal spreader of PTMT any colour for fixing with 15 mm dia pipe. complete all as specified and directed.

S&F PVC connection 15mm dia with PTMT nuts of length 450mm complete all as specified and directed by

S&F 110mm bore PVC (SWR) pipes ISI marked single sockets in any length with rubber ring joints fixed to wall and floor complete all as specified and as directed.

S&F PVC(SWR) 110mm bore bends, diminishing pieces or tapers complete all as specified and as directed.

S&F 75mm bore PVC (SWR) vent cowl ISI marked complete all as specified and as directed.

S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed.

M&L for concrete type C-2, 1:3:6 using 20mm graded aggregate as in bed to drain pipes including packing under, and haunching against the sides of 150mm bore of pipes after they are laid and tested complete all as specified and directed.

M&L for 150mm bore salt glazed stone ware(SGSW) drain pipe,grade 'A' laid in trenches and jointed complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting new drains, for internal dia of 150mm pipe and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

Supply & fixed CP Stop valve (concealed type)(ISI Marked), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore and fixed in repair complete all as specified.

S&F 15mm bore chromium plated shower roses with arm (size of arm 195mm long with bend to 45 degree) complete all as specified and as directed.

S&F vitreous china wash down water closet pan European type(pedestral pattern), white including cplastic water closet seat,black,closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed

S&F of 10 ltrs capacity PVC valveless, syphonic action type flushing cistern, low level, white with inlet ball valve, float and handle including brackets & flush pipe of polythylene of low or high density or PVC 32mm dia complete all as specified and directed by Engr-in charge.

S&F vitreous china wash basin, white flat back, size 550 x 400 mm excl taps, waste chain and plug and porcelain stopper but incl brackets, waste pipe & CP waste coupling.

S & F 28 mm dia fancy type drapery rod of mild steel duly powder coated wood finished with fixing brackets and fancy type, stopers etc complete all as specified and directed.

S&F health faucet with one meter tube and hook complete all as specified and directed.

S&F CP toilet paper holder complete all as specified and directed.(make: Cat part No BA-08 of Make-Prayag or its equivalen ).

S&F 605x605mm Anodised aluminum snap grid frame work including 6mm thick AC 'E' classic board decoreative of size 600 x 600mm as use in false ceiling fixed as per manufacturer's instructions complete as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-In-Charge.

M&L PCC 1:3:6 type C1 using 20mm graded agg as in bed block or for embeding of holdfast including necessary form work as specified and directed.

M&L for RCC M25 (Design Mix) as in slabs supported on walls, beams, columns in floors, roofs , landings, balconies, canopies, deckslabs, shelves & the like complete all as specified and directed by Engr-In-Charge.

M&L for RCC M25 (Design Mix) in beams,cantilevers, bressumers, lintels over 1.5 m span etc complete all as specified and directed by Engr-In-Charge.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat rough finished surface of concrete complete all as specified and directed by Engr-In-Charge.

M&L for formwork to chajjas including edges rough finished surface of concrete flat complete all as specified and directed by Engr-In-Charge.

M&L for formwork to sides of pillars, posts, struts, piers, columns etc rough finished surface square, rectangular on plan or polygonal complete all as specified and as directed.

M&L for Formwork to edges of rough finished surface of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

M&L for mild steel TMT bars 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-In-Charge.

S&F mild steel welded mesh not exc 4 Kg per sqm, welded to mild steel frame and fixed to steel members complete all as specified and directed.

S & F flat iron clamps, hold fasts, wall ties, hooks for hanging fans and other similar small steel article confirming to Fe – 290 Grade – E 165 with and including necessary nut-bolts, washers, screws etc. as required complete all as specified and directed

M&L for 5mm thick plaster rendering on fair faces of concrete surfaces as in ceiling in CM(1:3) finished even and smooth (without using extra cement) complete all as specified and as directed by Engineer-in-Charge.

M&L for three coats of white washing on ceiling including preparing new plastered surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for providing and applying single component acrylic polymer modified, fibre reinforced waterproof coating brushbond Roof Guard in 3 coats (white, grey and terracotta) of application @ 0.5 litre /sqm coat, including sprinkling of clean sand (300 microns - particle size).The product should have following properties solid content : 70%, tensite strength (ASTM D 412): 1.10 MPs, elongation (ASTM D12) : 100% Resistance to ageing due to UV radiation . 1000 hours no change rapid chloride penetration : very low resistane to algae growth passes, zero rating / permeability (mm): 5.0 water vapour transmission : 6.0gm/sqm h No of coats : 3 (minimum) adhesive bond strength : > 0.92 N/mm2, complete all as specified and directed.

M&L for applying two coats of weather proof all guard exterior emulsion paint over a coat of primer including necessary putty to new plastered surface of wall including preparation complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in Soft/loose soil complete all as specified and directed by Engr-In-Charge.

M&L PCC 1:2:4 type B2 using 20mm graded of aggregate with using 20mm graded stone aggregated in roof kerbs or mud stops, rounded or chamfered on edges, in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including using necessary formwork complete all as specified and directed.

S&F steel work in tubular trusses vertical pipes in columns, MS plate including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161 1979 grade st 240 with one shop coat complete all as specified and directed by Engr-In-Charge.

S&F Pre- painted galvalume aluminum zinc coating coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M&L for 60 mm thick machine pressed precast conctete interlocking paver block with grery cement and pigment, any shape and size confirming to IS 15658-2006, M-40 Grade with grey cement and pigment including 25mm thick sand cushion complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm (nominal cross-sectional area) PVC insulated unsheathed single core copper cable working voltage 1100 volts grade conforming to IS-694 with stranded copper conductor in and including PVC conduit of adequate size with all accessories (including cutting chases & making good the disturbed surface to its original specification) including MS sunk box, 3mm thick hylum sheet top cover fixed by means of brass machine screw and cap washer including size 1.5 sq mm (nominal cross sectional area) PVC insulated unsheathed single core multistranded copper conductor cable as earth continuity conductor connected to main switches/DB's or common earth dolly complete all as specified and directed for the following :- (a) One light point controlled by one way switch 5/6 amps.

(b) One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps.

(c) One socket out let 5/6 amps point on the independent board.

(d) One socket out let 5/6 amps point on the same board

All as per item No 101.00 here-in- above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board

S&F of switch piano flush type 5/6 amps single pole one way complete all as specified and directed.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and directed by Engr-in-Charge.

S&F switch piano flush type 15/16 amps single pole one way all as specified.

S&F of ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

S & F of deluxe fan Electronic regulator AC 50 Hzs rotary step white/ivory finish complete all as specified and directed.

S & F of lamp holder, insulated body, with back plate suitable for batten/angle fittings omplete all as specified and directed.

S&F of LED tube light fittings 1 x 18/20 watts energy efficient T5, 230 V incl 1x18/20 watt LED tube, epoxy powder coated CRCA sheet bipin holders, connector block etc, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable.

S&F of LED street light luminaires 35/36 Watts IP 66 type incl standard fittings pressure die cast aluminium housing with heat reistant toughened glass housing with epoxy powder coated finsh and , complete with Electronic driver and all accessories duly prewired and connecting to cealing Rose with and including GI Pipe 40 mm dia light grade bend to required shape, clamps, bolts and washers complete all as specified and as directed.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole and neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/lsolators complete all as specified and as directed.

S&F RCCB with MCB, Single pole & neutral, 32 Amps with sensitivity of 30 mAmp suitable for 240 volts, complete all as specified and as directed.

S&F of MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete all as specified and as directed.

M&L for Earthing complete with galvanised steel plate electrode of size 600x600x6mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 4 mm dia earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 15mm bore (Light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I 2009 including testing on completion all as specified and directed.

M&L for LED retrofit Lamp 1x14 Watt (white) 230V B-22 holder base with polycarbonate body and aluminium heat sink complete all as specified and directed by Engineer-in-Charge.

Supply & fix of fans ceiling with all accessories 230 V,1200 mm sweep. BEE 5 star rated complete with pre wired with 3 core cable all as specified and directed by Engineer-in-charge.

Supply and fixing of Sheet metal enclosures with socket two pin and earth plug top and MCB SP-20Amp 230 volt including taking down the old one complete all as specified and directed by Engr-in-Charge. Make: Havells/Standard/Legrand or of equivalent.

Supply & fix of Exhaust fans AC single phase 230 Volt of size 380 mm sweep with louver and ,wall cutting dia should be 25mm more than the sweep diameter complete all as specified and directed.

Supply, laying, jointing and testing in trenches or passing through pipe 1100 volt grade, XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured LT electric power UG cable heavy duty with stranded aluminium conductor of cross-section area 25sqmm 3.50 core witrh all fixing and connecting accessories such as aluminium cable lugs, cable glands nbut, bolt, washer etc complete all as specified and as directed. (Note : (i) Earth work and excavation GI pipe etc shall be required and paid separately. (ii) Specification of cable are as under :- (a) Inner sheathing shall be extruded PVC. (b) Cable shall be supplied with sequences hall marking at every metre on the inner sheeting. (c) Ultra violet radiation resistance compound comprissing to ASRM-2863 flame retarded as per EIV specification. (d) Anti roddent and antitermite compound added. (e) PVC compound of various grade as IS-5831. (f) Compaction conductors shall be shaped and arrangement to the same will be onthe cable.

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / laying under ground electric cable including taking out old bricks from trenches and separating serviceable bricks and set aside for reuse complete all as specified and as directed.

Returning, filling in, including spreading levelling watering and well rammming in layers not exceeding 25 cms in depth complete all as specified and as directed.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed.

Supply and laying sub class B bricks of size 25cmx15cmx7.5cm for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed.

M&L for 25 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified and as directed.Make: Tata/Jindal/Bansal

Dismantling of LT Panel/ Feeder pillar box/ Junction box from its position after demolition of foundation, disconnecting of all incomming/outgoing electrical cable connections and Shifting and Refixing of LT Panel/ Feeder pillar box/ Junction box of any type and size where as directed with and including painting with two coats of synthetic enameled paint over a coat of red oxide primer by using spray machine, including PCC (1:3:6) type C-2 as in foundation including necessary excavation, earth work and connecting all incomming and outgoing LT UG cables complete all as specified

M&L for point wiring with 1.5 Sqmm (nominal cross-sectional area) PVC insulated unsheathed single core FRLS copper cable working voltage 1100 volts grade conforming to IS-694 with stranded copper conductor in and including concealed In stove enamelled steel conduit of adequate size having a wall thickness not less than 1.5 mm with all accessories (including cutting chases & making good the disturbed surface to its original specification) including size 1.5 sq mm (nominal cross sectional area) PVC insulated unsheathed single core multistranded copper conductor cable as earth continuity conductor connected to main switches/DB's or common earth dolly, including wiring from DB to switch board with 2.5 Sqmm FRLS multistranded copper cables, complete all as specified and directed (a) One flameproof light point controlled by one rotary type switch 15/16 amps.

S&F Switch flameproof rotary type with termination box in LM6 16A, double pole 250V. complete all as specified and as directed

S & F LED tube light fittings 1x16/20W flameproof type made of aluminium alloy LM6,with electronic ballast,bipin holders,connector block,gland,etc. Complete with all accessories prewired and including connecting up with twin core twisted flixible copper conductor cable with suitable size andt complete all as specified and as directed.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Tripple pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/lsolators complete all as specified and directed

S&F MCB, Tripple pole & neutral, 63 amps, 415 volts, ‘C’ curve, 10 KA all complete as specified and as directed

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed

Supply and fixing aluminium strip of size 25x3.15 mm for earth continuity conductor fixed on PCC block complete all as specified as directed complete all as specified and as directed.

Supply and fixing porcelain insulator of size 65x31 mm and height 30mm with three nos hole including GI bolts and nuts of required size and two nos washer on PCC, fixing strip complete all as specified and as directed.

Supply and fixing air termination single pointed aluminium rod 12mm dia and 300 mm dia complete all as specified and as directed.

M&L 20 mm bore steel tubing light grade ISI marked for lightining protection including necessary joints complete all as specified and as directed.

S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 nos 8 mm dia 25 mm long hex.head screw complete all as specified and as directed.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cables, heavy duty with aluminium conductor of cross sectional area 50 sq. mm,3.5 core with all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc all complete as specified and as directed. (Note : (i) Earth work and excavation GI pipe etc shall be required and paid separately. (ii) Specification of cable are as under :- (a) Inner sheathing shall be extruded PVC. (b) Cable shall be supplied with sequences hall marking at every metre on the inner sheeting. (c) Ultra violet radiation resistance compound comprissing to ASRM-2863 flame retarded as per EIV specification. (d) Anti roddent and antitermite compound added. (e) PVC compound of various grade as IS-5831. (f) Compaction conductors shall be shaped and arrangement to the same will be onthe cable.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cables, heavy duty with aluminium conductor of cross sectional area 10 Sqmm,4 core with all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc all complete as specified and as directed. (Note : (i) Earth work and excavation GI pipe etc shall be required and paid separately. (ii) Specification of cable are as under :- (a) Inner sheathing shall be extruded PVC. (b) Cable shall be supplied with sequences hall marking at every metre on the inner sheeting. (c) Ultra violet radiation resistance compound comprissing to ASRM-2863 flame retarded as per EIV specification. (d) Anti roddent and antitermite compound added. (e) PVC compound of various grade as IS-5831. (f) Compaction conductors shall be shaped and arrangement to the same will be onthe cable.

M&L 40 mm bore steel tubing light grade ISI marked for protection of cable laid in horizontal bore including necessary joints complete all as specified and as directed

Supply and fixing LED luminaire with high power LED and unique peanut lens to ensure uniform light distribution ,higher spacing between poles and maintence free system of not less than 25 Watts IP 65 type incl standard fittings pressure die cast aluminium housing, heat reistant toughened glass, epoxy powder coated finsh complete with Electronic driver, 1.2 Mtr long 25mm dia light grade GI pipe, two MS clamps, nut, bolt and washers and all accessories duly prewired complete all as specified and directed.

M&L for Single piece aluminium deep drawn street lighting luminaire with acrylic cover Rediance new for B22 CFL/LED Bulbs Type with and including LED lamp B22 15 Watt, 1.2 Mtr long 25mm dia GI pipe, MS clamp, nut, bolt and washers complete all as specified and directed by Engineer-in-charge

S&F of Sheet metal enclosure for 6 way Distribution Boards (DB’s), Double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/lsolators complete all as specified and directed

S&F of MCB, Single pole & neutral,5 to 32 amps, 240 volts, ‘C’ curve, 10KA all complete as specified and as directed

M/S SARKAR BROTHERS

L. B. SHARMA

SG ENTERPRISE