JJM CWSS to Ponnani and adjoining panchayaths- Phase II-Supply erection testing and commisioning of HT centrifugal clear water pumpsets and allied works at WTP site Nariparamba - Package 7

Amount

SUPPLY AND ERECTION OF HT-HCF MOTORS AND PUMPS

OD99378/2023-2024: Supply, erection, testing and commissioning of KWA prequalified reputed make Centrifugal pump sets with Bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolts & nuts etc. complete suitable for coupling the pump and motor above the base plate etc. complete including providing suitable concrete foundation including cost of cement sand and metal etc. complete The duty condition is as follows Discharge - 150 LPS Total head - 57 mtrs.

OD100185/2023-2024:Supply, erection, testing and commissioning of KWA pre qualified reputed make horizontal solid shaft foot mounted TEFC squirrel cage induction motor suitable for the above pump working 3 phase 50 Hz AC supply, working voltage 3300V. The motor shall confirm to EEF1/IS 325 including providing suitable concrete foundation including cost of cement sand and metal etc. complete For 3300v motors digital motor protection relay shall be included in starter as per present IE rules. Flexible coupling shall be used for coupling of pumps and motors.

OD99673/2023-2024:Supply of 8" cast steel gate valves cast steel ASTM A 216 wcb gate valves, bolted bonnet, rising stem, AISI 410 trims, renewable seat rings, gearwheel operated, flanged end to ASA 150#.

OD99688/2023-2024:Supply and fixing of ON-OFF TYPE 415V AC THREE PHASE ELECTRICAL ACTUATOR OPERATED RESILIENT GATE VALVE of 200 mm WITH INTEGRAL STARTER UNIT.

OD99689/2023-2024:Supply 8" cast steel check valve cast steel ASTM A 216 wcb wafer type

OD99718/2023-2024:Supply and erection of 3 Ton X 2.79 Mtrs Span, 6 Mtrs Lift height, Single Girder EOT Crane with 3T Hoist, 200 mm ismb 30 mtr for gantry custruction, projected bracket supporting for gantry girder ismb 200 x 10 nos, providing base plate 20 nos by injection mortar paste on concrete beam, 40 sq bar for rail 30 mtr, 3x10 sq.mm ug cable 60 mtr for electrification of E.O.T crane and allied works, etc. providing with 12 months warranty.

OD99704/2023-2024:Supply and erection of 3 Phase , 3 HP Monoblock Vacuum Pumps of reputed Make with Speed- 3000Rpm, providing with a warranty period of 12 months.

OD119126/2023-2024:Supply, Installation, Testing and Commissioning of 10 kVA Three phase UPS system with 30 Minutes backup for Motorised Valves (0.37kW) - 8Nos. with 24 months warranty and UPS change over panel and contactors Including control &Power cabling upto 25 Meters.

OD122077/2023-2024:Fabricating MS pipes of size 700 mm (ID) using 16 mm thick MS plate including cost and conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete: For pipes fabricated with 16 mm thick MS plates. Mild steel plates

OD122075/2023-2024:Fabricating M.S. flanges of diameter 700mm using 24mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 16mm thick M.S. plates.

OD122107/2023-2024:Cutting 700 mm (ID) MS pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc. complete: For pipes fabricated with 16mm thick MS plates.

OD122088/2023-2024:Grinding cut and weld edges of 700 mm (ID) MS pipes during fabrication work including all labour and hire charges of tools etc. complete: For pipes fabricated with 16mm thick MS plates.

OD122097/2023-2024:Welding 700 mm (ID) MS pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods ,all labour and hire charges of tools etc. complete: For pipes fabricated with 16mm thick MS plates.

CONSTRUCTION OF BRICK WALL, FLOORING AND OTHER ALLIED CIVIL WORKS

15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

50.6.1.2:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

11.36:Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

21.1.1.1:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

Electric Project Consultants

Bidder Name

Electric Project Consultants

SURAS AGENCIES