CA NO.CWE BLY/GE (W)/18 OF 2025- 2026SPECIAL REPAIR TO COMMUNITY HALL IN DAD RESIDENTIAL COLONY LEKHANAGAR BAREILLY UNDER GE (WEST) BAREILLY

Amount

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M & L Brick work with Fly ash bricks straight or curved on plan exc 6m mean radius built in cm 1:4 complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to on brick masonary wall surfaces or on other than fair faces of brick masonary fair finished without using extra cement with using water proofing liquid complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall internal surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 on concrete surface of ceiling and soffit & finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of old distempered surface of walls by brushing, scrapping down smoke soot mouldsby steel wire brush and applying Two coat of distemper oil emulsion distemper over 2 mm thick Plaster of Paris putty complete all as specified and directed

M&L for preparing of New Plaster surface of walls and applying Two coat of distemper oil emulsion distemper over 2 mm thick Plaster of Paris putty complete all as specified and directed

M&L for preparing of old distempered surface of ceiling by brushing, scrapping down smoke soot moulds by steel wire brush and applying one coat of oil bound distemper over 2mm thick Plaster of Paris putty complete all as specified and directed

M&L for preparing of New plaster surface of ceiling by brushing, scrapping applying two coat of oil bound distemper over 2mm thick Plaster of Paris putty complete all as specified and directed

M&L for applying two coats of white cement based putty including sand papering the puttied surfaces to form an even and smooth surface, and applying two coats of weather proof exterior emulsion paint over and including priming coat of exterior primer over new or untreated plastered surfaces to be applied with fully automatic airless spray machine with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI, by allowing 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.

M&L for applying two coats of white cement based putty including sand papering the puttied surfaces to form an even and smooth surface, and applying two coats of weather proof exterior emulsion paint over and including priming coat of exterior primer over Old or untreated plastered surfaces to be applied with fully automatic airless spray machine with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI, by allowing 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.

M&L for preparation of newly plastered or untreated surfaces and applying three coats of white wash to walls complete all as specified and directed.

M&L providing cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in benching, coping, bed blocks including necessary form work, weathering slightly rounded or chamfered angles and throating, complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc complete all as specified and directed.

M & L fo Mat finishr non- skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes even and rough with and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M & L for Mat Finish non- skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes even and rough with and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M & L for colour glazed ceremic coloured tiles in vertical surface 350x250x7 mm/350x450 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick screed bed or bedding layer of cement mortar 1:4 cement and dismantling of wall tile including cement mortar bedding complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25 mm thick and size exc 0.16 sqm over 20 mm thick screed bed in cm 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and treating the surface incl complete complete all as specified and directed.

M&L for 20-25mm thick Machine cut kota stone slab as in riser and steps, skirting in full length in single peice without joint, with groove cutting in double line of stair width laid over 20 mm thick cement screed in cm 1:4 and jointed with rubbing and treating the surface incl bull nosing complete all as specified and directed.

M & L for double charged vitrified ceramic light shade coloured tiles 10 mm thick (Square or Rectangular) polished, area of each tile exc. 0.42 Sqm but n. exc. 1.00 sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including screeding 15mm thick in CM 1:6 and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of rubbish from the permises of site to low lying area complete all as specified and directed.

M & L for double charged vitrified ceramic light shade coloured tiles 10 mm thick (Square or Rectangular) polished, area of each tile exc. 0.42 Sqm but not exc 1.00 sqm as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including plastering 10 mm thick in Cement Mortar 1:4 and dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), including removal of rubbish from the permises of site to low lying area complete all as specified and directed.

Taking down of chowkats of frames n.exc 1.5 Sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed.

Taking down of chowkats of frames exc 1.5 Sqm but n exc 4 sqm each with shutters (without taking of shutters from the frames) complete all as specified

Taking down shutter of any description not exc 1 sqm each complete all as specified and directed.

Taking down shutter of any description exc 1sqm and not exc 2 sqm each complete all as specified and directed

S&F Pressed steel frames of size 125 x 60 x1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.including one shop coat of red oxide primer including cutting holes and making good in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. Note : 10mm deformed bar shall be provided in bottom portion in each frame. The rate for the same is included in rate quoted against this item. , complete, as specified,

S&F Pressed steel frames of size 105 x 60 x 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,including one shop coat of red oxide primer including cutting holes and making good in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. Note : 10mm deformed bar shall be provided in bottom portion in each frame. The rate for the same is included in rate quoted against this item. etc., complete all as specified and directed.

S&F for 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed .

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs.The frame shall be covered with fiber glass from all sides M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and complete all as specified and directed.

Supply and fixing 30 mm thick Fiberglass ReinforcedPlastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P.laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

M & L for 5.5 mm thick sheet glass, ordinary quality fixed with rubber beading and glazing clips in squares exceeding 0.5 sqm in each pane complete all as specified and directed.

M & L for 12 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work etc complete all as specified and directed.

S & F sheet glass ordinary quality 4 mm thick and glazing with oil putty/glazing clips of any description complete all as specified and directed.

S&F of Steel windows with pressed steel frame ( size 95x45x1.25mm) side hung shutter including box type hinges with steel handle, and steel peg steel complete with glazed openable shutter with glazing bar (open out side) and wire gauged openable shutter without glazing bar ( open in side) dovetailed or welded complete all as specified and directed and all as per Drg No TD/088 dt 07 Jan 2002 Note:- (i) Two shutter ie wire gauged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit. (ii) Rate for filling of PCC in frame deemed to be included in quoted rate. (ii) MS grill shall be measured and paid seperatly under relevant item of schedule

S&F powder coated aluminium sliding windows frame with movable shutter ( sliding on minimum two PVC roller of best quality) for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick tinted glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below, and following items deemed to include- (i) Window frame :68.4x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over (iii) Aluminium beading - 0.7mm thick (iv) Aluminium grill with Bulb height 4.5 mm square shape fixed on frame including necessary fixing arrangement like U-clip, flat Aluminium section maching with window & dia of grill as directed by Engr-in-Charge. (v) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (vi) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vii) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) fixed in vertical position with aluminium vertical members and specified thick tinted glass including rubber beading and aluminium glazing clips complete all as specified.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 all as specified and directed.

S&F for steel ventilators with top fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Glass shall be measured and paid for separately).

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-inCharge.

S&F 100 mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed.

S&F 75 mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm long Aluminium handles cast type anodised complete all as specified and directed.

S&F 125 mm long Aluminium handles cast type anodised complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasps staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed.

M&L for painting to steel surface exc 10 cm width or girth with two coats of synethic enamel paint over a coat of red oxide primer including preparation of newly or previously untreated surface complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames glazed with putty of fixed with beads as specified and directed by Engr-in-Charge.

S&F sheet glass of 3mm,ordinary quality and glazing with oil putty or wooden beading in squares n.exc 0.5 Sqm in each pane,complete all as specified and directed.

M & L for painting to wood and wood based surfaces of any description exc. 10 cm width or girth with two coats of synthetic enamel paint over a coat of pink primer including prepration of new or previously untreated surfaces complete all as specified and directed..

Dismantling water tanks and removing to store capacity exc 250 and not exc. 500 litres complete all as specified and directed.

S & F 500 ltrs capacity rotational moulded polythylene water storage tanks triple laye white in colour (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

S & F for 15mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed.

S&F for 20mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed.

Refixing old steel tubing and connection in new or old position (wall, ceiling,floor etc.) bore of pipe 20mm complete all as specified and directed

Refixing old steel tubing and connection in new or old position (wall, ceiling,floor etc.) bore of pipe 15mm complete all as specified and directed

S&F in repairs chromium plated fancy type long body bib taps with cast copper alloy screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore pipe complete all as specified and directed.

S&F in repairs chromium plated fancy type stop vlave /angle valves with cup cast copper alloy screwed down high pressure, screwed both ends for iron pipes or for unions for 15 mm bore pipe complete all as specified and directed.

S&F in repair 15 mm dia fancy type stop cock (concealed ), chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed complete all as specified. Make Jaquar, Cera, Kohler

S&F 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified or as directed.

S&F in repair PVC connection 15mm dia size with PTMT nuts of length 450mm complete all as specified and directed

S & F in repair PTMT grating size 125 mm fixed with white cement complete all as specified or as directed.

S&F in repairs 6 x 6 inches ultra slim shower head with 12 inches arm of Chromium plated brass for fixing 15 mm pipe with bend of 45 degree with flange complete all as specified and directed.

S&F in repair for 15 mm dia concealed stop cock fancy type, cast copper alloy chromium plated long shank and cup washers, crutch or butter fly handle, screwed down, screwed for iron pipe of 15mm bore all as specified or as directed.

S&F in repairs tubular, towel rail brass chromium plated 20mm dia D type 60 cm long between flanges complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as spd and directed

M & L for PVC (SWR) floor trap/Nahani Trap, dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F32 mm Waste coupling of PTMT (half or full threaded) weight 40 gm as specified and directed

S&F PVC (SWR) vent cowl 75 mm dia complete all as specified and directed.

S&F in repairs Vitreous china wash basin white flat back of size 550mm x 400mmx excluding tap, waste, chain & plug but including brackets complete all as specified and directed.

S&F vitreous China Urinal half stall type white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar 1:3 including PTMT spreader, PTMT waste coupling, PVC waste pipe complete all as specified and directed.

Supply and Fixing in repairs Vitreous China Ware Urinal partition slabs 310x700 terminating about 40 cm above floor line complete all as specified and directed.

S&F Pillar taps in repairs fancy type cast copper alloy, with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and screwed for pipe and fixed basin mixture 15 mm dia complete all as specified and directed.

S&F in repair for PVC low level flushing cistern 10 Ltrs capacity with all internal accessories and fixed to wall including provision of PVC connection pipe 15mm bore with brass union and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC etc complete all as specified and directed.

S&F in repair for A Vitreous china wash down water closet (Pedestal Pattern) EWC white (excluding flushing cistern & flush pipe) complete in all respect all as specified. or as directed..Make Jaquar CNS-WHT- 551SSPP/CERA -S1053101/HINDWARE-20044/Approved Make and sample approved by GE

S&F in repair for vitreous china squatting pan 'Orissa' pattern of size 580mm x 440mm white with integral foot rest with 'P' or 'S' trap, front or back inlet and connection to trap with cement mortar etc complete all as specified and directed.

Taking up or down AC/PVC rain water pipe, soil/waste/vent pipe of any size with fittings etc. complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floorl complete all as specified and directed.

S&F 110mm PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 75mm PVC (SWR) bends any radius complete all as specified and directed.

S & F framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw including bending and welding angles as necessary gusset plates, riveting etc, n.exc 10 Kg each brackets conforming to Fe-290 Gde E-165 (Brackets over 10 Kg each to be measured under Structural steel.

M & L for Plain Cement Concrete 1:2:4 in surface chanel and drain work etc complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

S&F 25mm dia stainless steel decorative curtain rods of any pattern, design & colour with end fittings and brackets complete all as specified and directed.

Demolition of Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

M&L for RCC type B1, 1:2:4 (20 mm graded aggregate) as slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection 75 mm thick finished even and fair or as specified or as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 sectiion) in cement concrete 1:2:4 (type B1) smooth finished, and reforming benching as required of pipe 100mm dia complete

Concrete bed to drain pipes of 100mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 complete all as specified

M & L for precast reinforced concrete 1:2:4 type B1 using 20 mm graded stone aggregate for cover slab set in and pointed in CM 1:6 including necessary formwork complete all as specified and directed.

Demolition of cement concrete(unrinforced), in any position and paving n.exc. 15 cm thickness( below or above ground level) including tile/ terrazzo floor complete all as specified and directed.

M & L for plain cement concrete 1:2:4 type B-0(using 12.5mm graded stone aggregate) in sub base 25 mm thick as specified or as directed.

S & F in repairs floor door stopper of aluminum alloy body and tongue, overall length of cover plate 140mm, anodised with hard drawn steel spring, overall length suitable for aluminium door/ wooden door complete all as specified and directed.

S & F second class hardwood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including repairs to disturbed existing surfaces complete all as specified and directed

S & F aluminum wire cloth of 0.45 mm nominal dia of wire and average width of aperature 1.4 mm, fixed with aluminum wire staples complete all as specified and directed.

S & F in repair alumimum die cast body door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters of 801 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F mild steel spring for doors 300 mm long, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as specified

S & F in repairs 100 mm cast iron sanitary connection socket to fit WC out let complete all as specified and directed.

M&L Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position coomplete all as specified and directed.

S & F for glass corner shelf in Bathroom 225 x 225 mm with chromium brackets and fixed with screwed in bathroom corners as spd and directed

M&L 2nd class hard wood 100x75 mm Handrails rounded or shaped with splayed faces in straight length and fixed with sunk to receive iron core including dismntling old wooden rail all as specified and directed

M&L for painting to steel surface exc 10 cm width or girth with two coats of synethic enamel paint over a coat of red oxide primer including preparation of old pained surface complete all as specified and directed.

M & L for painting to wood and wood based surfaces of any description exc. 10 cm width or girth with two coats of synthetic enamel paint over a coat of pink primer including prepration of old painted surfaces all as specified or as directed.

M & L for French polishing to wood and wood based surfaces of any description, width or girth including cleaning and preparing the surfaces including a coat of wood filler on new works with two or more coats all as specified or as directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation complete all as specified & directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M & L Formwork to sides of concrete foundations, footings, bases of columns, raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or batter, finished rough surfaces of concrete, complete all as specified and directed.

M & L Formwork to sides of pillars, posts, struts, piers, columns complete all as specified and directed.

M & L formwork to sides and soffits of lintels,lintel bend, roof beams etc finished rough surfaces of concrete complete all as specified.

M & L for Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and directed.

M & L Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in foundation, footing, plinth beam, base of columns etc complete all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in columns, pillars, piers, post and structs etc complete all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in roof Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in slab, shelves etccomplete all as specified and directed.

M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in chajjas, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed.

M&L for 20 mm thick granite (of any type and shade) work (table rubbed and polished) in floors, steps, jambs, pillars, window cills, cooking plateforms and like in CM 1:4 incl pointing in white cement(1:2) using marble dust with admixture of pigment to match the shade of granite stone including grinding and polishing, moulding of edges complete over and incl 15 mm thick screed bed or bedding layer of mortar in cement mortar 1:4 complete incuding hole for gas pipe complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and 1.5m deep for foundation etc in soft/loose soil and getting out complete all as specified and directed.

Returning, filling including spreading, levelling and well ramming in layers not exceeding 25 cm in each layer as in hard / dense soil complete all as specified and directed.

Removing excavated soils n.exc 50mtrs and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

S&F Stainless steel railing with horizontal pipe of 32mm dia , vertical pipe of 50mm dia and nosing of 75mm dia at spacing of 200mm horizontal and 300mm c/c of vertical including embedding in steps/ walls with necessary holdfasts, PCC 1:2:4 bed blocks etc complete all as specified and directed.

M&L for 4mm thick E-Board classic (everest or equivalent) tiles for insulation and accoustic purpose 60cm x 60cm with and including powder coated galvanised iron snap grid with 32x25x1.5mm thick Tee section and 32x25x1.5mm thick algle section with all hanging/supporting arrangements as in false ceiling and making good disturbed surface complete all as specified and directed.complete all as specified and directed.

M & L for plain cement concrete 1:2:4 type B-0(using 12.5mm graded stone aggregate) in roof top and floor 25 mm thick complete all as specified and directed.

S&F Steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections ) including distance pieces, cleats, nut bolts etc complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / clading to wall, fixed with self tapping screws as specified. Complete all as spd and directed.

S&F prepainted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / clading to wall, fixed with self tapping screws as specified. Complete all as spd and directed.

S & F stainless steel plate rack not less than 5 Kg (size 900mm x 600 mm) in repair complete all as specified and as dirrected.Make : SSKPR-315 Blue Star/Nirali/Equivalent Make approved by GE

S&F in repairs stainless steel glossy finish kitchen sink with double bowl over all size 1100mmx545mm and bowl size 460mmx460mmx230mm) without drain board made of 1 mm thick 304 grade stainless steel with plugs,washers and waste pipes & coupling, round strainer including bedding in cement mortar to dwarf wall/granite slab including necessary fitting required and connecting union to pipe including chromium plated waste fitting and PVC flexible waste pipe of approved quality complete all as specified and directed.

S&F in repairs chromium plated wall mixture 3 in 1 of 15 mm bore dia of pipe with connection for shower arragement complete all as specified and directed. Make Jaquar SOL-CHR-6281/KohlerK-98754-IN-4-CP/Grohe-32211001, approved Make and sample by GE

S&F in repairs chromium plated WHB/Sink basin mixture 2 in 1 of 15 mm bore dia of pipe with connection for shower arragement complete all as specified and directed.

M&L for cutting chases,for concealed water tubing and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F Prelam PVC sheet wall panelling of thickness 5mm consisting panels of desired size stuck on inner frame work of 35mm wide strips of 5mm thick PVC sheet. The PVC strips shall be fixed to the wall using 65mm long MS screws through the groove in the strip by using PVC fastners. The distance between two screws shall not be more thant 200 mm. The strips shall be fixed to wall vertically at an equal interval of 10" between two PVC strips. A strip of 5mm thick PVC sheet of width 75mm feathered at edges shall be stuck at the places where two panels are jointed, using solvent cement and including taking down existing PVC wall paneling complete all as specified and directed.

Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surfacecomplete all as specified and directed.

Taking down carefully UNSV main switch DBs of any description of an size in any position complete all as specified and directed.

Taking down submain wiring including all accessories complete all as specified and directed.

Material and labour for point wiring with single core FRLS 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with all conduit accessories, screws (concealed conduit wiring in walls and casing capping on ceiling or roof) including metal box suitable for modular fittings and covered with modular plate and cover of suitable size with new brass screws for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:-

(a) One light / fan/ exhaust fan point controlled by one switch.

(b) One 5 pin 5 Amp switch socket out let point on an independent board complete all as specified and directed.

(c) One 5 pin 5 Amp socket out let point controlled by one switch on same board complete all as specified and directed.

(d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent complete all as specified and directed.

(e) One light point controlled by two 2 - way switches , on indepndent board complete all as specified and directed.

All as per item 144 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded incl 2.5 sq mm FRLS PVC copper conductor single core used as earth continuity conductoe complete all as specified and directed.

S & F Modular switch one way 10 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular switch Two way 10 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular switch one way 16 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular bell push 6 Amp, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular fan regulator Step up type, 120 Watt, 2 Module complete all as specified and directed by the Engr-in-Charge.

Supply and Fixing ceiling rose PVC / Poly carbonate, Isolated body, three terminal AC 230 volts complete all as specified and directed.

M & L for replacement of lamp holder, PVC / Poly carbonate, insulated body modular type with back plate batten/angle type for batten fittings complete all as specified and & directed

S&F in replacement LED mirror light fitting of 1 x 20 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

S&F in replacement LED mirror light fitting of 1 x 10 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection complete all as specified and directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing surface mounting LED slim square down lighter made of PDC Al with high efficint LEDs and glare free opal diffuser, IP 20 12 watt 220 volts AC complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and Fix LED lamp 12 Watt, 230 V , AC integrated circuit complete all as specified and directed.

Supply and fixing Buzzer, Ding Dong AC. 230 volts,single pole complete all as specified and directed.

Supply & Fixing Bldg security light fitting, LED type, 25 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed.

Supply and fixing post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

M&L for sub main wiring with two single core 4.0 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. ( Note :- Two runs of 4.0 sqmm (FRLS) and one run of 4.0 sqmm (FRLS) copper conductor shall be measured as one unit length.)

M&L for sub main wiring with two single core 6.0 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. ( Note :- Two runs of 6.0 sqmm (FRLS) and one run of 6.0 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Taking down carefully ceiling fan from existing site and depositing in MES yard complete all as directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed by the Engr-in-Charge.

S&F MCB SPN 40 Amp 240 volt complete all as specified and directed by the Engr-in-Charge.

S&F MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed by the Engr-in-Charge.

S&F MCCB Triple pole and neutral 100 Amps 415 Volt curve 10 KA complete all as specified and directed by the Engr-in-Charge.

Supply and fix flush sheet metal enclosure SPN DB 8 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete including taking down old unsv complete all as specified and directed.

Supply and fix flush sheet metal enclosure SPN DB 12 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete including taking down old unsv complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

Taking down carefully electric/electronic meter and fixing the same after bldg repair all as directed by Engineer-in-Charge.

Supply and fix TPN DB -VTPN DB 4 way with provn of MCCB 160 Amps , 415 Volt, 3 Phase, 4 wire AC 50 Hz having aluminium Bas Bar phase and the neutral insulated with PVC sleeves, connected with appropriate size copper thimbles.complete all as specified and directed.

M&L for earthing and testing complete with galvanized iron earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 M below normal ground level with top edge plate at adepth not less than 1.5M below normal ground level connected to and including earth lead GI wire 4 mm dia, by means of bolts and nuts,check nuts and washers etc.,made of GI and connected to panel/distribution board and earthing test point and earth dolly all as shown in elect plate No.3 of SSR Part-1 including necessary earth work,excavation PCC chamber cover with handle (PCC 1:2:4) incl 20mm dia GI pipe of medium grade for watering and 15mm dia GI pipe of light grade for protection of earthing lead ,wire mesh, funnel, charcoal dust,common salt,copper lugs etc all as specified and directed .

Taking down carefully service connections of any dsecription from pole, wall or service brackets etc including making good disturbed surface to match with the existing surface complete all as specified and directed.

Supply and laying & testing UG cable XLPE, insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor , of size 50 Sqmm 3.5 core complete all as specified and directed.

M & L for sand cushioning, laid in trenches for laying LT UG Cable complete all as specified and directed.

M & L for old size bricks common burnt clay building bricks, sub class 'B' designation -75 for LT UG Cable protection complete all as specified and directed.

S & F for GI tubes, light grade, of 80 mm dia, with all fittings and fixed complete for protection of LT UG Cables, laid in flooor or fixed on walls or along with poles etc complete all as specified and directed.

RIYASAT ALI KHAN (BID ID -3354107)