PROVN OF 01 X TOILET BLOCK NEAR SLITHERING HEPTR AT PT GRND 02X COVERD

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Add to (or deduct from) above item for every 3cm or part there of above or below 15 cm average depth complete all as specified and directed.

Excavation in trenches in soft & loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes,foundations,laying of cable, shafts, well, cesspits, manholes etc. complete all as specified and directed.

Excavation in post holes (or similar holes) not exceeding 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick as in soft / loose soil including watering & removing surplus soil material to a distance not exceeding 50 mtr & making good surface complete all as specified & directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers of not exceeding 25 cm thick after the cables & pipes etc. are laid, jointed & tested and foundations complete all as specified and directed by Engineer-in-Charge.

Spreading, leveling, watering and well ramming in layers of not exceeding 25 cm thick including watering as required complete all as specified and directed

Removal of surplus excavated spoil not exceeding 50 Mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified.

Removal of surplus excavated spoil exceeding 250 mtr but not exceeding 500 mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring, foundations,filling & mass concrete for fencing posts, foundation of pole ,struts & stay assembly etc complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in foundation including rafts, footings,plinth beams, and mass concrete etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use & waste of form work to sides of concrete foundation, base of coloumn ,rafts,footings, plinth beams, and plinth beam and similar work for rough finished flat surfaces of concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in columns,pillars,piers,popst and struts etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides of columns,pillars,piers,post and struts for rough finished surface of concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in lintels beam, floor/roof Beams, cantilevers, bressummers, , etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in chajja etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides of soffit of chajja,chullah hoods,troughs & similar items etc including for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to sides of soffit of suspended slab such as roof slab ,floor slab ,landing and similar work , not exceeding 200 mm thick for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to sides and soffit of lintel Beam,floor/roof Beams, etc for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor & roofs and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide rough finished surface of concrete complete all as specified and directed.

M&L for Brick work using fly ash bricks old size , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

M&L for half brick thick Brick work using fly ash bricks old size , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 etc complete all as specified & directed.

M&L for Brick work using fly ash bricks old size , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 etc complete all as specified & directed.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engr-In-Charge .

S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as fixing in the frame at site as per specification and drawing including 3 Nos stainless steel butt hinges 100 mm long for each door, complete all as specified and as directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed.

S & F 100mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed .

S&F 150mm aluminium alloy handles, cast type, anodised complete all as specified & directed.

M&L for framed work such as grills,gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railing; framework of water tanks and similar work conforming to Fe 290- Gde E -165 & for portions framed and hung as gates, including pintle hinges, stops,hand-made sliding bolts, etc.complete all as specified and as directed

S & F for steel ventilator with top hung shutter including hinges, steel peg stay, complete including prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

M&L for preparation of newely plastered surfaces of wall and applying three coat of white wash on new wall surface complete all as specified & directed.

M&L for preparation of newely plastered surfaces of ceiling and applying three coat of white wash on ceiling surface complete all as specified & directed.

S & F vitreous China urinals, bowl type angle back, size of 430 x 370 x 340 mm white (minimum),with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)(back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe etc.complete all as specified and as directed

S & F vitreous China half stall type (back to corner )urinals with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)(back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe etc.complete all as specified and as directed

M&L for preparation of newly plaster surface of wall and applying two coats of cement base paint over a coat of alkali primer including necessary scaffolding complete all as specified & as directed.

S& F for Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples windows complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over grade Fe-500, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to flooring/hard standing etc ,complete all as specified and directed.

M&L for mild steel TMT bars 08 mm dia and over grade Fe -500 , as in stirrups, spacers & binders ,cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for hard core of broken stone or boulder gauge not exceeding 63mm deposited, spread & leveled in layers not exceeding 15cm thick, watered and rammed to a true surface etc complete all as specified& directed.

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushed stone aggregate ) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 grade and sand in the ratio 1:3 including necessary form work , complete all as specified and directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

M & L glazed ceramic coloured tiles of size 375 mm x 250 mm x7mm/450 mm x 300 mm x7 mm thick ,as in dado/skirting etc ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles including 10 mm thick rendering in cement plaster in CM (1:4), complete all as specified and directed.

M&L for rendering 10 mm thick on brick masonry/concrete surface etc in CM (1:6) surface finished even & smooth using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair face brick masonry/concrete surface etc in CM (1:4) surface finished even & smooth using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in CM 1:4 on concrete surfaces as in ceiling finished even and fair complete all as specified and directed.

M&L for prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

M&L for rendering 15 mm thick on brick masonry/concrete surface etc in CM (1:4) in two layer ,mixed with water proofing compound , trowelled to fair finished even & smooth without using extra cement complete all as specified and directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

M&L for rendering 15 mm thick on brick masonry/concrete surface etc in CM (1:4) surface finished even & smooth without using extra cement complete all as specified and directed.

S &F aluminium work for doors, windows, ventilators shutters(fixed/sliding track two or three track) and partitions frames with extruded built up standard sections of approved make fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions with sealent with wall, i.e. at top, bottom and sides including cleat angle, C.P. brass/ stainless steel screws, all complete all as specified and directed.

S&F anodised aluminium doors, windows, ventilators shutters ,aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips rubber packing anodised aluminium, snap beading screws, powder coated aluminium fittings such as peg stays 150mm long (1No.),100mm long hinges type B-21 (2Nos), suitable handle(02 Nos.) in each door top rail guide rail etc. complete all as specified and directed.

S&F 3.0 mm thick figured glass pin headed type in squares/ rectangular not exceeding 0.5 Sqm in each pane glazing with oil putty or aluminium frame/shutters with rubber neoprene beading complete etc all as specified & directed.

Taking up or down steel tubing and connections of 15 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

Taking up or down steel tubing and connections of 20 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chasees for brick walls and making good the surfacein cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls /laid in trenches and ceiling or laid in floors including cutting chasees for brick walls and making good the surfacein cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 25 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls /laid in trenches and ceiling or laid in floors including cutting chasees for brick walls and making good the surfacein cement mortar 1:3 complete all as specified & directed.

Refixing for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)complete all as specified & directed.all as specified & directed.

Refixing for 20 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)complete all as specified & directed.all as specified & directed.

S&F rotational moulded polythene water storage tank of capacity 1000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed.

S&F rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed.

S&F bib taps , cast copper alloy with capstan head or butter fly handle,chromium plated screwed down with high pressure screwed for iron pipe and fixed 15 mm bore complete all as specified & directed.

S&F in repair bib taps , cast copper alloy with capstan head or butter fly handle,chromium plated screwed down with high pressure screwed for iron pipe and fixed 15 mm bore complete all as specified & directed.

S&F stop valve 15mm bore chromium plated fancy type cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall etc complete all as specified and directed.

S&F in repair stop valve 15mm bore chromium plated fancy type cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall etc complete all as specified and directed.

S&F angle stop valve chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15 mm bore complete all as specified & directed.

Supply only pillar taps fancy type, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed.

S&F stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 20 mm bore for oron pipe or unions complete all as specified & directed.

S&F stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 25 mm bore for oron pipe or unions complete all as specified & directed.

S&F 20 mm bore ball brass valves,high pressure,with polythene float and flynut ,screwed for iron pipe or brass ferrule and fixed complete all as specified & directed.

M & L for 50 mm thick damp proof course PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate )mixed with integral water proofing compound (as per manufacturer’s instructions) or @ 3% by weight of cement)conforming to IS: 2645 including covered with 100 micron thick polythene film complete all as specified & directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

S&F for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F 75 mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches ,floor or in wall complete all as specified and directed.

S&F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches ,floor complete all as specified and directed.

S&F 150 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches ,floor complete all as specified and directed

S&F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F 75 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F 75 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 110 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F in repair 110 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F in repair 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110mm PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed.

S&F 75 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F for 150 mm X 150 mm ,Salt-glazed stoneware gully traps, square or round mouthed, type 'P' complete all as specified and directed.

S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement with chromium plated grating with or without hole complete all as specified and directed.

S&F WC squatting pan " Orissa Pattern" of size 580 mm X 440 mm white with integral foot rest including cast iron "P" or "S" trap, front or back inlet and making connection to trap & to flushing cistern complete all as specified & directed.

S&F WC squatting pan " Orissa Pattern" of size 580 mm X 440 mm white with integral foot rest including cast iron "P" or "S" trap, front or back inlet and making connection to trap & to flushing cistern complete including taking down existing pan & making good disturbed surface complete all as specified & directed.

M&L for 50 mm thick plain cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in sub-base of floor/hardstanding etc surface finished even and rough to receive the topping etc complete all as specified & directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in cover slab for manhole, chullah,hoods, chajjas, water troughs,mangers, shelves and similar articles with plain faces & drain including setting in cement mortar 1:6 including necessary formwork etc complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately)

S & F PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S & F in repair PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S & F vitreous China wash basin, any colour, flat back size 550 mm X 400mm including 32mm brass chromium plated waste coupling ,PVC 32 mm bore waste pipe, chromium plated Grating including bracket , fixing of pillar tap & PCC 1:2:4 ,type B-1 (using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed. Note : Pillar tap as supply only will be measured & paid seperately under respective item of BOQ.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) in kerbs or mud stops, rounded or chamfered on edges water troughs and the like including necessary form work complete all as specified and directed.

M & L for 10 mm thick screed bed in cement mortar 1:4 mixed with using liquid water proofing compound as per manufacturers instructions over roof top surface finished even and smooth using extra cement and application of water proofing treatment using APP modified roof membrane over non accessible/ non approachable RCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface)to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying approved bituminous based primer @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface & hot blown grade bituminen 85/25 @ 1.2 Kg/Sqm over primer . (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Applying two coat of bituminious based Aluminium Paint @ 0.3 Kg /sqm over APP Membrane. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

Supply only liquid water proofing compound complete all as specified and directed.

M&L for 60mm thick factory made machine pressed pre-cast concrete coloured interlocking paver block of approved shade of any shape and size conforming to IS-15658-2006 of M-35 grade laid over & including cleaned dry sand cushion bed 50mm thick over & including 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as sub-base, surface finished even and rough over and including 75mm thick Hardcore of broken boulder of gauge n exc. 63mm, deposited, spread and levelled, watered and rammed to a true surface, etc complete all as specified and directed.

M & L for 100 mm thick Concrete bed to 150 mm bore drain pipe including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate )complete all as specified & directed.

M & L for 150 mm thick Concrete bed to 150 mm bore reinforced concrete drain pipe ,class NP-3, laid and jointed in trenches complete all as specified & directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in base of PVC tank etc including necessary form work complete all as specified and directed.

Supply and fixing 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F rolled mild steel sections as in framed structure with main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and fixed with angle cleats or other connecting plates, mild steel angle, flat iron ,Z- sections(ISI mark) conforming to Gde Fe-410-0 or Fe 310-0 complete all as specified & directed.

S & F fo Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,in kerb/benching/copings including weathering, slightly rounded or chamfered angle and throating including use & waste of necessary form work etc complete all as specified and directed

M&L for plain cement concrete 1:2:4 ,type B-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and directed

M&L for Conventional type of Septic Tank for 25 users including necessary earth work in excavation in any type of soil, plain cement concrete 1:2:4 type B-2 ( using 40 mm graded crushed stone aggregate ) as in foundation , brick work in cement mortar 1:4 , ,reinforced cement concrete M-25 ( design mix) as in slab cover including pre-cast man hole cover slab having 8 mm dia TMT bar reinforcement @ 75 mm c/c & 6 mm thick mild steel plate embedded all around of cover slab , 15 mm thick plaster in cement sand mortar in 1:4 on wall, vent shaft, sludge chamber , form work to sides and soffits, 150 mm dia SGSW inlet & out let pipes up to 3 m from outer face of wall, CI vent pipe, sludge chamber, RCC baffle wall, returning filling & removal etc, complete all as shown on drawing No.TD CEJZ/TD/57/2000 , Sheet No. 01 as specified.

M&L for Construction of Soakage well for 1.80 dia( internal dia ) & 3.0 m (effective depth) including necessary excavation in earth work in any type of soil , plain cement concrete 1:3:6 type C-2 ( using 40 mm graded crushed stone aggregate ) as in foundation , brick work in cement mortar 1:4 in walls & honey combed brick wall , reinforced cement concrete M-25 ( design mix) as in slab cover including pre-cast cover slab having 8 mm dia TMT bar reinforced,plain cement concrete band and dwarf wall, form work to sides and soffits of RCC slab & filling with brick bats loose filling including interconnecting pipes of RCC /DWC complete all as specified and shown in drawing No.TD- CEJZ/TD/58/2000 Sheet No. 01 complete all as specified.

M & L for 40mm thick (measured solid),providing precast cement concrete 1:2:4 ,type B-0 ( using 12.5 mm graded crushed stone aggregate ) as in louvres and jallies, including all mould- ings but excluding frame including setting in cement mortar 1:4 including necessary formwork etc complete all as specified and directed.

S & F 150 mm (overall length of cover plate) floor door stopper with rubber shoes aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) in for inserting hold fast of doors & window & similar work etc. including necessary form work complete all as specified and directed

S&F brass chromium plated shower rose with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specifed & as directed.

S&F vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device complete all as specified and directed. Note : Plastic seat cover shall be measured separately as Supply only as considered under respective items.

Supply only plastic water closet seat closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F towel rail brass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flanges fixed with and including chromium plated brass screw & wooden /plastic cleats complete set all as specified and directed.

M&L for plain cement concrete 1:2:4 ,type B-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains & benching including finishing the top of benching even & smooth using extra cement complete all as specified and directed

M&L Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, etc (inner girth only to be measured) complete all as specified and directed.

Add or deduct for each 25mm girth or part thereof over or under 30cm -ditto-

Dismantling old Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified & directed.

S&F roof trusses (framed), trussed, purlins, crane guntries, rail, fastening ,heavy bracket ,rafter,framing (beam, tee, angle, channel or flat sections) distance pieces, cleats including fabrication and fixing conforming to Fe-410-W(Gde E-250) quality-A complete all as specified & directed.

M&L for demolition of cement concrete (un reinforced)in ground floor & paving of any thickness (aboveorbelow ground level )by mechanical tools and removing excavated material exceeding 1.50 km and not exceeding 5.0 km complete all as specified and directed

M&L for 100 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to flooring/hard standing etc ,complete all as specified and directed.

M&L for 50 mm thick plain cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in floor/hardstanding etc surface finished even and smooth without using extra cement complete all as specified & directed.

Taking down cement plaster of brick or stone masonry etc including raking out joints , hacking for key & scrubbing down with water etc complete all as specified & directed.

Taking down chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) etc including builders hardware etc complete all as specified & directed .

Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out off MOD land etc complete all as specified and directed.

S & F health faucet(ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connection & fixed in position complete all as specified & directed.

S & F for Bib taps two way with wall falnge cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15 mm bore fixed complete.MAKE : Jaquar or equivalent all as specified and approved by Accepting Officer.

M & L for Loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified & directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified & directed.

Demolition and breaking up rain water pipes (SGSW/PVC/ AC/ RCC) of internal dia 150 mm, set in cement mortar including removal of debris out off the MOD land complete all as specified and directed.

M&L for drilling in existing water pipe, taking new tapping from existing pipe,proper welding to the pipe surface complete all as specified and directed

Taking down carefully unserveciable/damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets ,light fittings etc) and removing material from site and making good to the disturbed surface to match with existing finish etc complete all as specified and directed.

M&L for point wiring for one light/fan/exhaust fan point /exhaust fan/ bell /buzzer point controlled by one way switch with using with FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 1.5 Sq.mm nominal cross sectional area for phase & neutral and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steel sheet terminal box made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminated cover make sheet for housing/fixing switches etc., complete all as specified and directed. Note: Proper colour coding to be adopted.

All as per item No 143 here-in-before but 5 Amp socket outlet on same board.

All as per item No 143 here-in-before but for 5 Amp switch socket on independent board.

M&L for point wiring with FRLSH PVC insulated PVC sheathed electric cable confirming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 2.50 Sq.mm nominal cross sectional area for phase & neutral & including non metallic rigid PVC conduit ISI marked medium grade not less than 25 mm dia with all conduit accessories in concealed wiring system & 2.50 Sq.mm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including pressed steel anodized sunken boxes 60 mm deep & 1.6 mm thick duly painted inside & anticorrosive outside with Bakelite hylem sheet 2.80 mm thick complete for one six pin switch socket outlet combination ,15 Amps & 5 amp socket point on independent board controlled by one ,one way switch complete all as specified and directed.

S & F switch piano flush button single pole one way 5 Amp, complete all as specified and as directed.

S & F socket outlet 2 in 1, 3 pin, 5 Amp, flush type, universal, complete all as specified.

S & F Switch socket combination 2 in 1, 3 pin, 5Amp and 15 Amp flush type, universal, complete all as specified.

Supply and fix ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified.

S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified.

S & F ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified.

S & F LED light fitting 1 x 20watt , 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S&F 1X9 W/1X10 W watt LED Bulkhead fitting with IP 65 environmental frendly, ultra modern, energy saving mounted decorative oval bulk head edge lit LED luminaire comprising of high brightness LED 230 Volts AC circuit complete all as specified and as directed. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S & F LED bulb of capacity 10 watt , lumen out put (950)lm ,length 102 mm dia 56 mm , base cap B22 (ISI mark) complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S & F steel body Exhaust fan of 300 mm sweep blade with louvers shutter , frame single phase ,230 V,50 Hz,1200 RPM AC ,copper winding , including provision of hole, mounting frame, nut, bolts, washer, fasteners etc and connecting exhaust fan to ceiling rose including provision of three core flexible copper cable of size 1.5 sqmm not less than 0.5 mtr long for connection complete all as specified & directed.

S & F sheet metal enclosures for DBs when MCBs to used single pole and neutral (SPN) double door 240 volts, 4 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F in repair sheet metal enclosures for DBs when MCBs to used single pole and neutral (SPN) double door 240 volts, 4 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F amp rating 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

S&F in repair miniature circuit breaker (MCB) SP 6 to 32 Amps ('C' Series) having current rating 10 KA complete all as specifed and as directed .

S & F in repair amp rating 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

S & F 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

Supply, laying , jointing & testing LT under ground cable XLPE insulated, screened ,PVC bedded, galvanised steel strip or wire armoured, electric power cable ( heavy duty) with standard aluminium conductor , 1100 Volts grade of cross sectional area 10 Sq mm 2.0 core complete all as specified and directed.

Supply, laying , jointing & testing LT under ground cable XLPE insulated, screened ,PVC bedded, galvanised steel strip or wire armoured, electric power cable ( heavy duty) with standard aluminium conductor , 1100 Volts grade of cross sectional area 6 Sq mm 2.0 core including taking down existing cable complete all as specified and directed.

Material & labour for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed by Engineer-in-Charge. NOTE:- For measurement purpose punned thickness shall be considered as per clause 19.75 of SSR Part-I.

Supplying & Laying un-reinforced pre-cast flat concrete cable protection cover of class LV, type- 2, size 250 mm x 150mm x 40mm, factory made, complete all as specified and directed by the Engineer-in-Charge.

S & F 20 mm bore GI tube, light grade for cable protection with all necessary fitting, complete with all fittings laid as in floor etc., complete all as specified and as directed.

S & F 50 mm bore GI tube, light grade for cable protection with all necessary fitting, complete with all fittings laid as in floor etc., complete all as specified and as directed.

M&L ,for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts check nuts & washers of galvanised iron or steel, protected by GI pipe 15 mm bore (light grade) and watering pipe 20 mm bore GI pipe (light grade) and PCC of chamber and coping shall in 1:3:6 type C-1 using 20 mm graded stone aggregate including excavation and earth work and removal of surplus soil and filling with black cotton soil upto ground level complete all as shown in electrical plate No 3 of SSR Pt-I, 2009 with CI cover 10mm thick of size 300x300mm with charcoal dust and common salt complete and earth lead connected to panel including testing complete all as specified and directed. Note : Earth test reports shold be submitted by the contractor duly tested in the presence of Engineer-in-Charge.

M&L ,for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts check nuts & washers of galvanised iron or steel, protected by GI pipe 15 mm bore (light grade) and watering pipe 20 mm bore GI pipe (light grade) and PCC of chamber and coping shall in 1:3:6 type C-1 using 20 mm graded stone aggregate including excavation and earth work and removal of surplus soil and filling with black cotton soil upto ground level complete all as shown in electrical plate No 3 of SSR Pt-I, 2009 with CI cover 10mm thick of size 300x300mm with charcoal dust and common salt complete and earth lead connected to panel including testing including taking down existing earthing complete all as specified and directed. Note : Earth test result should not less than one ohm.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing bweinching for and forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required in 150mm internal dia pipe complete all as specified and as directed.

S&F energy saving new generation environmental frendly long life versatile pressure die cast aluminium IP 66 ,for security light fitting luminarie with high power LED as light source and electronic driver of capacity 25/35 watts with necessary mounting arrangements including provn of three core cable of copper conductor of size 2.5 Sqmm, PVC insulated in white colour from ceiling rose to fitting terminal for making connection and all necessary fixing accessories such as bracket of GI pipe light grade Suitable bore as per fitting 1.20 mtr long bend in required shape, MS clamp 40x3mm thick fixed on wall including bolts & nuts all as specified and directed Make- Crompton Greaves cat No- LSTS-45-CDL-M or equivalent or Bajaj or C&S

S & F LED mirror type light fittings 1 x 10 watts with high out put diffuser 2 feet ,220 volt ,AC decorative type with driver holder & LED lamp & all other accessories duly pre wired and making connection with and including three core copper flexible wire from connector to ceiling rose not less than 1 mtr fixed on wall with plastic gutties complete all as specified & directed.

S&F switch socket combination 2 in 1 ,5 pin , 5 Amp flush type , universal , complete all as specified

M &L for point wiring for one light point controlled by ne switch 1100 volt grade PVC insulated unsheathed 1.5 sqmm multi stranded FRLSH copper conductor cable with continuos earth wire of 1.5 sq mm multi stranded copper conductor cable PVC insulated unsheathed , drawn in & including rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia & PVC board bakelite sheet , covered with 2.8 mm thick laminated insulated cover make sheet for housing /fixing switches etc complete all as specified and directed.

S & F gun metal globe or gate valve with iron wheel head srewed at both ends for iron pipe for size 20 m dia complete all as specified and directed

M/S Parmar Construction