Installation of Fire Safety Equipment in Girls Hostel G8 at GADVASU, Ludhiana.

Amount

Fire Pump Room Work Electric Motor Driven Hydrant and Sprinkler Pumps (Location : Plant Room) :Pumps will be Factory assembled comprising of following:S/E, installing, testing and commissioning of Electrical motor driven fire pump suitable for automatic/ manual operation consisting of the following 'Horizontal end suction single/ double stage centrifugal fire pump capable of delivering 2280 LPM against a total head of 88m, 2900 RPM with multi spring mechanical seal, wearing ring complete with connection to suction and delivery line, and includeing bypass aggangement for testing of pumps. Pump shall have a name plate indicating, head discharge, stages, RPM and direction of rotation.Epoxy coated common base plate for mounting pump and motor fabricated of mild steel channel as per manufacturer's recommendation with required no. of heavy duty Anti Vibration pads. Technical Parameter Main Hydrant & Sprinkler Pumps:- Flow rate/Discharge : 2280 LPM , Head - 88 m, Motor HP - 75 HP (Approx.) or as per manufacturer recommendation.Material of construction:- Casing - CI, Impeller - Bronze, Shaft - SS 304, RPM - 2900 RPM, Seat mechanical seal ,Rate should be inclusive of foundation bolts, viberation elimination peds complete in all respect as desired by Engineer -In-Charge (Make Kirloskar,Crompton,KSB)

Diesel Engine Driven Fire Pump (Location - Plant Room) : Pumps will be Factory assembled comprising of following:Supplying, installing, testing & commissioning of Diesel Engine driven fire pump suitable for automatic/manual operations consisting of the following : 'Horizontal split case single/double stage centrifugal fire pump capable of delivering 2280 LPM against a total head of 88 M at 1800 RPM, Heat Exhanger cooled engine with two nos of 50 mm dia pressure reducing valves , 4 nos of ball valves, 2 nos strainers and 2 nos pressure guages, complete with proper connection to suction and delivery line, and including bypass arrangement for testing of pumps, mechanical seal, drain, etc. Pump shall have a name plate indicating, head, discharge, stages, RPM and direction of rotation.Common base plate for mounting pump & engine of required strength manufactured out of M.S. channels as per manufacture's recommendation with required no. of heavy duty Anti Vibration pads.Flexible Coupling & coupling guard for direct coupling of engine & pump.Suitable For Installation on reinforced cement concrete pump foundations as per manufacturer design including foundation bolts, washer as required.1 No. 6 hours capacity day oil storage tank (Minimum 200 Ltr) of welded steel construction conforming to IS : 2522 fabricated from 4 mm thick M.S. plates. Tank shall be provided with inlet, outlet, overflow, air vent, drain connections, filling connection & magnetic level indicator showing the level of fuel in the tank. Tank shall be mounted on a suitable mild steel structure (Painted with 2 coats of red oxide paint). Tank shall be provided with epoxy coat from inside & two or more coats of synthetic enamel paint outside over two coats of red oxide primer. Diesel storage tank shall be double skin. 12 volts lead acid battery with boost/Trickle charger for starting the engine automatically complete as required. Technical Parameter of Diesel Engine driven pump: Flow rate/Discharge : 2280 LPM ,Head - 88 m,Engine BHP - 105 or as per manufacturers.Material of construction,Casing - CI,Impeller - Bronze,Shaft - SS 304,RPM - 1800 RPM,Seat mechanical seal,Rate should include foundation bolts, vibration elimination pads, etc complete.Item as Described above complete in all respect as desired by Engineer -In-Charge (Make Kirloskar,Crompton,KSB)

Electrical Motor Driven Jockey Pump Location - Plant Room : Pumps will be Factory assembled comprising of following: Supplying, installing, testing & commissioning of electrical motor driven Jockey pump suitable for automatic/manual operation consisting of the following: Horizontal multistage jockey pump with cast iron body, Bronze impeller, stainless shaft with mechanical seal capable of delivering 180 LPM against total head of 68 M at 2900 RPM complete. The system shall be complete with pressure gauge with gun metal shut off cock on delivery side. The pump should meet the recommended requirement and must be approved by the local fire authority. Common base plate for mounting pump and motor fabricated of mild steel channel as per manufacturer's recommendation with heavy duty required Nos. Anti Vibration pads.Suitable reinforced cement concrete pump foundations as per manufacturer's design including foundation bolts, nuts and washers as required.Rate shall include inter connecting foundation bolts etc. complete.Technical Parameter of Jockey Pump :Jockey Pump :-Flow rate/Discharge : 180 LPM ,Pumping head: outlet-68 M head,Seat mechanical seal,Motor HP : 15 HP (Approx.) or As per manufacturer recommendation,Item as Described above complete in all respect as desired by Engineer -In-Charge. (Make Kirloskar,Crompton,KSB)

Providing & fixing MS pipe Class ‘c’ diesel engine exhaust pipe (including all fittings, clamps, steel support thick glass wool isulation with 24 guage aluminium cladding, bird proof cowl, etc.) of suitable dia for the engine. The pipe shall be provided with 12 mm thick supercera ceramic fibre rope. 80mm dia Exhaust Pipe.complete in all respect as desired by Engineer -In-Charge. (-make: Jindal Hisar/Tata/SAIL/Ispat)

Air Vessel for Fire Pump:Providing, fixing, testing and commissioning of air vessel (size 450mm dia & 2100mm height) fabricated from 8mm thick shell & dished end 10 mm thick M.S. Plate for hydrant/ Sprinkler system complete with 25mm dia sockets for pressure switches and pressure gauges, duly painted from inside the epoxy paint and outside with enamal paint complete as required along with 450mm high supporting legs (including duel type pressure switch for each pump) Note: Contractor should submit general arrangement drawings before fabrication of vessel and ultrosonic test report to be submitted on supply of vessel complete in all respect as desired by Engineer -In-Charge.

Providing & fixing and painting steel pipes to I.S. 3589(6.35 mm thick) or IS 1239 heavy class including all fittings, like, fasteners, structural supports, clamps, couplings, bends, elbows, tees,offsets etc. welded or flanged joints as required, Painted MS pipe structural support, fasteners as directed complete the work as per the requirement at site including painting with two coats of synthetic enamel paint, over two coat of primer after surface preparation, cutting holes and chases in brick or RCC walls and making good complete for pump suction and delivery piping. complete in all respect as desired by Engineer -In-Charge.(MAKE :- TATA ,JINDAL,HISAR) 100mm dia

Providing & fixing and painting steel pipes to I.S. 3589(6.35 mm thick) or IS 1239 heavy class including all fittings, like, fasteners, structural supports, clamps, couplings, bends, elbows, tees,offsets etc. welded or flanged joints as required, Painted MS pipe structural support, fasteners as directed complete the work as per the requirement at site including painting with two coats of synthetic enamel paint, over two coat of primer after surface preparation, cutting holes and chases in brick or RCC walls and making good complete for pump suction and delivery piping. complete in all respect as desired by Engineer -In-Charge.(MAKE :- TATA ,JINDAL,HISAR) 150mm dia

Providing & fixing and painting steel pipes to I.S. 3589(6.35 mm thick) or IS 1239 heavy class including all fittings, like, fasteners, structural supports, clamps, couplings, bends, elbows, tees,offsets etc. welded or flanged joints as required, Painted MS pipe structural support, fasteners as directed complete the work as per the requirement at site including painting with two coats of synthetic enamel paint, over two coat of primer after surface preparation, cutting holes and chases in brick or RCC walls and making good complete for pump suction and delivery piping. complete in all respect as desired by Engineer -In-Charge.(MAKE :- TATA ,JINDAL,HISAR) 200mm dia

Providing and fixing bucket type suction strainer with M.S. flanged connection suitable for 2280 lpm discharge fabricated from 8 mm thick M.S. plate and stainless steel 60 mesh with SS stiffner complete including companion flanges etc. suitable for 200 dia inlet and 300 dia outlet including inside with rubbersied paint and outside with two coats of enamel paints of approved shades after surface preparation necessary stainless steel butterfly nuts, bolts, washers etc.complete in all respect as desired by Engineer -In-Charge. Make JINDAL /TATA/RAVINDRA

Supplying, Installation, Testing and Commissioning of CI butterfly valve ISI marked with SS-316 grade disc following sizes tested for a minimum pressure of 16 Kg/cm² complete suitable for pad locking arrangement including supply and fixing of pad lock with universal key with rubber insertion, nuts, bolts and washers, matching flanges of required thickness, etc. complete as per specifications. and desired by Engineer -In-Charge (MAKE :- ZOLOTO,HONEYWELL,U FLOW OR EQUIVALENT ) 100 mm dia

Supplying, Installation, Testing and Commissioning of CI butterfly valve ISI marked with SS-316 grade disc following sizes tested for a minimum pressure of 16 Kg/cm² complete suitable for pad locking arrangement including supply and fixing of pad lock with universal key with rubber insertion, nuts, bolts and washers, matching flanges of required thickness, etc. complete as per specifications. and desired by Engineer -In-Charge (MAKE :- ZOLOTO,HONEYWELL,U FLOW OR EQUIVALENT ) 150 mm dia

Supplying, Installation, Testing and Commissioning of cast iron wafer type dual plate Non return valves with SS-316 grade disc of following sizes conforming to relevent IS specifications and tested for a minimum pressure of 16 Kg/cm² for sheet and 24 Kg/cm² for shell including companion flanges providing and fixing nuts, bolts, washers, gaskets etc. complete as required. (MAKE :- ZOLOTO,HONEYWELL,U FLOW OR EQUIVALENT ) 100 mm dia

Supplying, Installation, Testing and Commissioning of cast iron wafer type dual plate Non return valves with SS-316 grade disc of following sizes conforming to relevent IS specifications and tested for a minimum pressure of 16 Kg/cm² for sheet and 24 Kg/cm² for shell including companion flanges providing and fixing nuts, bolts, washers, gaskets etc. complete in all respect as desired by Engineer -In-Charge (MAKE :- ZOLOTO,HONEYWELL,U FLOW OR EQUIVALENT ) 150 mm dia

Supply & fixing of 4 nos. G.I. round bottom heavy quality fire buckets of 9 liters capacity filled with sand including proper supporting / mounting arrangements in MS angle iron frame, painted by fire red colour over two coats of red oxide paint and written with white paint "FIRE" complete in all respect as desired by Engineer -In-Charge.

Supply and Laying of 1000 mm wide and 5 mm thick insulated mat dame from highly electrical resistant elastomer of tested quality to withstand 30 KV dielectric strength as per IS:15652 complete in all respect as desired by Engineer -In-Charge.

Providing and Fixing of Danger Notice Plate of 200x 150mm made of 2mm thick MS Plate.

Providing and Fixing of Shock treatment chart written in English and Hindi both properly framed and glass covered as required.

Electrical Panel and Electrical work For Fire Pumps- Supply, installation, testing and commissioning of following fire fighting Automatic control panel for three pump sets suitable for 415 V, +/- 6% Volts, 3 phase, 4 wires, 50 Hz power distribution system. The panel shall be free standing floor mounting sheet metal enclosed dust and vermin proof conforming to IP-52, compartmentalized design, fabricated out of 14 SWG sheet steel, painting, earthing numbering, danger plate as per specifications and drawings , flush front with Aluminium busbars, separate earth bus bars to be provided throughout the length of the panel. The incoming and outgoing feeder breakers, fuses, indicating lamps etc shall be accommodated in a modular multitier arrangement. The painting shall done as per relevant IS codes/as specified in the specifications. Adequate size cable alley shall be provided all round the panel and in the back for each cable bending and termination. The panel shall be fabricated by TAC/Fire authority approved vendor. The outgoing feeders inside the panel shall be connected through solid bus bars. Flexible cable links are not acceptable. Bus bars shall be provided with heat shrinkable sleeves and shall be colour coded. The panels shall be suitable for cable entry from top. The panels shall be fabricated after the approval of fabrication drawings.All wires and cables used will be FRLS. 2 Nos. earthing terminals shall be provided for 3 phase, 415 V, 50 HZ supply system. M Lifting hooks shall also be provided in case of large panels. Cadmium plated hardware shall be used in fabrication of Panels.Including foundations/hanging arrangement if any, complete in all respect as desired by Engineer -In-Charge.

FIRE HYDRANT SYSTEM Providing and fixing stainless steel fire hydrant valve 80 mm inlet with matching flanges.single outlet with control and fitted with 63 mm dia instantaneous female coupling on the outlet complete with orifice flange as required, blank cap and chain locations as per drawings (inlet flanged to I.S. 5290-1969 Type A Class C) of superior make complete in all respect as desired by Engineer -In-Charge.

Providing and fixing brass fullway valve with C.I. wheel, screwed female ends conforming to I.S. 778-1971, Class III of superior make complete in all respect as desired by Engineer -In-Charge. a) 25mm dia

AUTOMATIC SPRINKLER SYSTEM S/L/J/T of following sizes of Heavy grade 'C' class mild steel pipe, flanges and fittings such as bends, tees, reducers, rubber insertions ,dash fastners and galvanized nuts and bolts, Heavy Class confirming to IS:1239-1974 Part-I and Part-II with fitting steel has M.T. S. of 320N mm ². upto-date amendments including fixing the pipe on wall/celing with suitable galvanized M.S. strip/clamps/bracket and painting with one coat of anti-corrosive paint/primer and two or more caots of synthetic enamel paint etc. complete as required ,Structral support shall be paid in relevant item complete in all respect as desired by Engineer -In-Charge. a) 25 mm nominal bore

AUTOMATIC SPRINKLER SYSTEM S/L/J/T of following sizes of Heavy grade 'C' class mild steel pipe, flanges and fittings such as bends, tees, reducers, rubber insertions ,dash fastners and galvanized nuts and bolts, Heavy Class confirming to IS:1239-1974 Part-I and Part-II with fitting steel has M.T. S. of 320N mm ². upto-date amendments including fixing the pipe on wall/celing with suitable galvanized M.S. strip/clamps/bracket and painting with one coat of anti-corrosive paint/primer and two or more caots of synthetic enamel paint etc. complete as required ,Structral support shall be paid in relevant item complete in all respect as desired by Engineer -In-Charge. c) 80 mm nominal bore

AUTOMATIC SPRINKLER SYSTEM S/L/J/T of following sizes of Heavy grade 'C' class mild steel pipe, flanges and fittings such as bends, tees, reducers, rubber insertions ,dash fastners and galvanized nuts and bolts, Heavy Class confirming to IS:1239-1974 Part-I and Part-II with fitting steel has M.T. S. of 320N mm ². upto-date amendments including fixing the pipe on wall/celing with suitable galvanized M.S. strip/clamps/bracket and painting with one coat of anti-corrosive paint/primer and two or more caots of synthetic enamel paint etc. complete as required ,Structral support shall be paid in relevant item complete in all respect as desired by Engineer -In-Charge. d) 100 mm nominal bore

Providing and fixing 15 mm dia gunmetal sprinkler head with quartz bulb and set to operate at specified temperature. Sprinkler head shall carry UL-USA approval complete in all respect as desired by Engineer -In-Charge. Temperature of operation 68 deg.C., K-80 a)Pendent type (conventional/upright)

Providing and fixing 15 mm dia gunmetal sprinkler head with quartz bulb and set to operate at specified temperature. Sprinkler head shall carry UL-USA approval complete in all respect as desired by Engineer -In-Charge. Temperature of operation 68 deg.C., K-80 b)Sidewall type (normal throw)

Providing and fixing Cast Iron butterfly valve as per IS: 13095 of Class PN 16, having epoxy coated disc, carbon steel shaft,EPDM / nitrile rubber field replacible body lining and of approved make. including a set of MS flanges, required nos. of nut & bolts complete in all respect as desired by Engineer -In-Charge.(MAKE :- ZOLOTO,HONEYWELL,U FLOW OR EQUIVALENT ) a) 80 mm dia

Providing and fixing Cast Iron butterfly valve as per IS: 13095 of Class PN 16, having epoxy coated disc, carbon steel shaft,EPDM / nitrile rubber field replacible body lining and of approved make. including a set of MS flanges, required nos. of nut & bolts complete in all respect as desired by Engineer -In-Charge.(MAKE :- ZOLOTO,HONEYWELL,U FLOW OR EQUIVALENT ) b) 100 mm dia

Providing and fixing electrically operated flow indicating flow switches with threaded connection for indicating water flow in sprinkler branch line oneach floor with necessary junction box installed in accessible place including provision of suitable socket in pipe line complete in all respects. complete in all respect as desired by Engineer -In Charge . (MAKE :HONEYWELL, BOSCH, NOTIFIER) a) Pipe dia 80-150 mm, Water flow upto 2850 lpm

FIRE EXTINGUISHERS Providing and fixing Mono Ammounium Sulphate 90% type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, Trolley mounted, conforming to IS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges as desired by Engineer -In Charge.(Make :-SAFEX/Minimax/Ceasefire) a) Capacity 25 kg-trolley mounted

Providing and fixing stored pressure vessel Mono Amounium Sulphate 90% Powder type fire extingushers consisting of seamless cylindrical body, squeeze lever dischange valve fitted with pressure indicating guage internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS : 15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. as desired by Engineer -In Charge (Make :-SAFEX/Minimax/Ceasefire). a) Capacity 6 Kg.

Main Fire Alarm Panel - UL Listed INTEGLEX MULTICREST N3060, 2 Signal line cuircuit analogue addressable fire alarm control panel, expandable upto 12 Loop with 10.4 inch Colar Touch Screen LCD display. Panel shall show the addrese map of at least 50% of devices of each loop on single window display on built in touch screen. Each loop shall have capacity to accomodate maximum 255 input devices in any combination along with output devices. max 6 nos of inbuilt programmable relay controls, max 8 nos of inbuilt NAC output controls, 230 volts AC power supply, automatic battery charger, Network option for 64 panels. Panel shall have capability to play pre recorded voice message announciation upon occurance of event like fire alarm, supervisory, trouble, device activation/failed etc. Panel shall have Inbuilt Telephone Circuit to work as Talkback system by connecting the telephone handset through telephone jack form the field Make: Bosch/honeywell(gamewell)/Siemens(fire finder)

S/E of 4" Detector Base (UL) with RI terminal Make:Bosch /honeywell (gamewell)/Siemens(fire finder)

Addressable Manual Fire Alarm Box: Addressbale MCP Pull type along with the Telephone Jack to connect the Telephone handset for talk back. MCP and Telephone jack should be mounted on the surfacemounted box.Make; Bosch/Jbl/Tannoy

Surface Mounting Adaptor for Manual Fire Alarm Box

Telephone Handset for Manual Fire Alarm Box for Talkback with FACP center by connetcing the handset with telephone jack

UL Listed Horn / Hooter (Adjustable sound level) complete with MS Powder coated Junction Box for mouting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling. MakeHoneywell/Bosch/ Notifier /Simplex/LST/Ceasefire

Addressable Monitored Output Module (UL) for connecting UL lisyted Hooter/Horn.MakeHoneywell/Bosch/ Notifier .

Addressable Twin Relay Module (UL)MakeHoneywell/Bosch/ Siemens)

Cable: 2x1.5 sqmm Armoured cable make Polycab/Havells/Finolex

Fire Suit TECHNICAL SPECIFICATION - Standard : European Standard - CE Certified to EN 469 : 2014 Outer Shell - Made from original Dupont 60z Nomex III A fabric. Moisture Barrier-Aramid/Kevlar non-woven Laminated with PTFE membrane for maximum. breathability & hydrostatic head (waterproof) performance. (EN 343 protection against foul weather) Thermal Barrier - Constructed using non-woven ARAMIDE KEVLAR fibers laminated with Nomex/Viscose innermost ling fabric for maximum protection. Reflective Tape- 2" Wide Fire Retardant - Lime Silver Lime Reflective Trims  Single Strip at chest area.  Double strips at bottom of jacket.  Double strips on sleeves of jacket.  Double strips on bottom of pants. ACCESSORIES:- 1.Firefighter Helmet: CE Certified to EN 443-1997 / EN 443-2008. 2.Firefighter Hood: CE Certified to 13911. 3.Firefighter Gloves: Certified to NFPA 1971. 4.Firefighter Boots: Certified to EN ISO 20345 & EN 15090 Complete suit set consists of the the following;Jacket & trouaer - EN 469:2014 Balaclava Hood - EN 13911 Fireman Helmet - EN 443 Fire Fighting gloves - EN 659 Fire Fighting Boots - EN 15090 Make- Nomex or equivalent.

SCABA SET CYLINDER:- MS STEEL TYPE, DURATION :-45 MINS,BAR :-300 BARS, CAPACITY :- 6 LTRS , PRESSURE TYPE :- POSITIVE PRESSURE, APPLICATION :- FIRE FIGHTING , CONFINED SEARCH ,RESCUE ,ESCAPE SCENARIO, PROTECT AGAINST ALL GASES. No Objection certification(NOC) as well as Fire Evacuation Plans/Exit Plans from every respective department of Government and Non Govermental Organisations (where ever necessary) related to Environmental and Disaster Management complete in all respect signed and attested by apropriate authority will be provided by the Contractor.

Supply of Powder Coated Door galvanized steel Flush Fire doors of Kindle Make . 2hrs Fire rating (Haryana Govt Lab.)and tested in accordance with IS 3614 Part 2, & BS 476 Part 22: FRAME: - Door frames to be Double rebate profile of 143 x 57 mm manufactured from 18 gauge galvanized steel, profile to have bending radius of 1.4 mm supplied in assembled form ready to install at site. SHUTTER: - Door Shutter in 46 mm thick manufactured from two 20gauge galvanized steel sheets lock seam jointed at stile edges to form a double skin fully flush shell. Infill of Properitory insulation material to be provided for structural rigidity & additional reinforcements & sound Insulation for all hardware fixtures as required Size :-2000*2000 mm Supply of SS Ball Bearing Hinges(04nos par leaf) - CE Marked, Supply of Fire Rated Door Closer, Supply of 6.8mm Thick Fire Rated Clear Wired Vision Panel size of :- 200x300mm, Supply of CE Marked Fire Rated Dead Lock, Supply of SS D Type Back to back D Type Handle 300x19mm, Supply of Dash Fastner 08nos. Per door with PVC Caps, Installation Charges for Double Leaf, Installation Charges for Single Leaf, Cartage and Packing, Supply of Flush Bolt.

PATHAK CONSTRUCTION CONSORTIUM

SECURED ENGINEERS PRIVATE LIMITED