SPECIAL REPAIR TO 11 X TOILETS (DEPOT AREA) OD TALEGAON, SPECIAL REPAIR TO BLDG NO T-78 AND T-79 AT 915 LT AD REGT (COMP) WKSP AND PROVN OF UNDERGROUND DRAINAGE FOR OR MESS AT 915 LT AD REGT WKSP (COMP) UNDER GE DEHU ROAD

Amount

Dismantling of wall & floor tiles, incl cement mortar bedding (but not backing) complet all as specified and directed by Engr-in-Charge.

M&L for glazed coloured ceramic tiles 300mm X 450mm x 7 mm thick as in vertical surfaces set & jointed in neat cement slurry & pointed in coloured cement incl backing coat 10mm thick in CM 1:4 finished even and fair to receive tiles all as direced.

M & L non skid coloured ceremic tles 7 to 8 mm thick area of each tiles exceeding 0.11 sq.m but not exceeding 0.18 sqm, in floors, etc.set and jointed in cement slurry and pointed in white or coloured cement to match. Including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc any type on any surfaces of wall and ceiling complete all as specified and directed by Engr-in-Charge.

M&L for rendring 10mm thick in CM 1:6 on fair faces of brick/ concrete ,wall surface is to be finished even and smooth (without using extra cement) with thin layer of sagol complete all as specified and as directed.

M&L for 15mm thick cement plaster on concrete/ brick surfaces in CM 1:4 and finished top surfaces even and smooth with using extra cement with water proofing compound complete all as specified and as directed. (Note : water proofing compound shall be measured and paid saperately)

M&L for 5mm thick cement plaster on concrete/ brick surfaces in CM 1:6 and finished top surfaces even and smooth with using extra cement complete all as specified and as directed.

M&L two coats of cement base paint to new plastered surfaces of walls including preparation of surfaces over a coat of cement primer complete all as specified & directed by Engineer-in-Charge.

M/L for three coat of white wash over a coat of chalk whiting on new surfaces of wall including necessary preparation of new surfaces etc complete all as specified and as directed.

M&L three coats of white wash to new plastered surfaces on ceiling including preparation of surfaces complete all as specified & directed by Engineer-in-Charge.

M&L for applying two coats of white wash on old decorated surfaces on walls including preparation of surfaces complete all as specified & directed by Engineer-in-Charge.

M&L for applying one coat of cement base paint on old decorated surfaces on walls including preparation of surfaces complete all as specified & directed by Engineer-in-Charge.

M&L for applying one coat of white wash on old decorated surfaces of ceiling including preparation of surfaces complete all as specified & directed by Engineer-in-Charge.

Taking down chowkats or frame with shutter (w/o taking off shutter from the frame) of area not exc 1.5 Sq.m complete all as specified and directed by Engr-in-Charge.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

Taking down steel window / ventilator of any size and making good the disturbed surface in CM 1:4

S & F louvered aluminium ventilators including frame with adjustable luvers with provision of fixing exhaust fan fixed with and incl 4mm thk frosted glass louvers and sall be fly proof with stainless steel wire gauge of 0.36mm dia and 1.18mm aperture fixed to frame with aluminium beading and following aluminium powder coated sections conforming of `JINDAL' or of equivalent make and rubber beading etc all as directed. (a) SP20048 (b) Glazing clipa 19352 and Decogrill DG 104 10mm tkNote : Cost of glass louvers and wire cloth shall be incl in the quoted rate of the items

S&F Aluminium alloy anodised sliding door bolt with hasp staple (bolt type) hand fixing clips of sheet cast or extruted section & fixing bolts & sliding blots of extruted sections of cast aluminium alloy & fixed 300mm long

S/F 150mm length Aluminium anodised barrel tower bolt of extruded section

S/F Aluminium handles cast type anodised 150mm long

Taking up or down steel tubing and connections including cleaning for refixing of 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing of 20mm bore of pipe complete all as specified and as directed.

M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to for concealed water tubing and making good, cutting not exc 10 cm girth

S & F 15 mm dia GI pipes medium grade galvanised with al fitting and fixed complete to walls and ceiling or laid in floors

All as per item No. 25 above but 20mm

S&F in repairs vitreous china squatting pan "Orissa pattern" size 580x 440mm white wash integral foot rest with provn of lime concrete bedding & jointing to flush pipe & socket of WC including 'P' or 'S' trap

S&F in repairs viterous china white wash basin counter top flat back or size 550 x 400mm pipe PVC connection 15mm dia x 450mm long with PVC down take pipe

S&F for virtreous china wash down water closet, pan white (pedestal pattern ) inlcuding plastic water closet black/white closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device excluding fixing bolts flushing cistern and flush pipe complete all as specified .

S&F in repairs vitreous China urinals half stall urinal (back or corner wall type), complete inlcuding providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including urinal spreader of PTMT any colour for fixing with 15mm dia pipe, PVC connection 15mm x 600mm long, waste coupling of PTMT (Half or full threaded) 40mm dia

S&F in repairs 15mm dia pillar taps cast copper alloy with capston head chromium plated screwed down high pressure wlth or without letter "Hot" or "cold" with long screwed shanks and flynuts

S & F in repairs 15 mm dia bib taps chromium plated fancy type , screwed down for iron pipes or for brass ferrule.

S & F in repairs 15 mm dia stop/angle valves fancy type , chromium plated with ,screwed high pressure with crutch or butterfly handles screwed both ends for iron pipe. Etc.

S& F in repairs PVC flushing cistern white colour 10 ltr capacity with inlet, ball valve, lever & bracktes etc.

S & F in brass chromium plated anodised tubular towel rail, 20 mm D type 60 cm long between flanges.

S & F in repairs 75 mm dia outlet long arm cast iron nahani trap with grating incl jointing to waste pipe fixed in cement concrete etc.

Dismantling of CI 110/75 mm pipes fixed to walls and floor with all fittings/ accessories complete all as specified and directed.

S & F PVC (SWR) pipes single sockated in any length with rubber ring joints fixed on walls dia 110 mm.

All as per item No.39 above but 75 mm dia

S&F PVC (SWR) bend 110mm dia with acess door

S&F PVC (SWR) bends 75mm dia with access door

S&F PVC (SWR) vent cowl 110mm dia

Dismanling water tanks exc 250 & n exc 500mm and removing to strore

M&L rotational moulded polythelene water store tank, cylindrical vertical with closed top hoisted and fixed in position all as specified capacity of tank 500 ltrs

S&F PVC ball valves, high pressure with apaxy coated aluminium rod and high dencity plaster ball screwed for iron pipe 20mm

Demolition of cement concrete ( unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone agg) as in plinth protection 75mm thick finished top surface even and smooth with using extra cement

Demolition & breaking up drain pipe (salt glazed, AC or reinforced concrete ) set in cement mortar for 200 mm dia pipe.

M&L for PCC ( 1:4:8) type D2 (using 40 mm graded stone aggregate ) as in bed to drain pipes, incl packing under & hauching against the sides of pipes after they are laid and tested for 150 mm bore RCC Pipe.

S&F of 150mm dia RCC pipe class NP-2 laid and jointed in trench after testing the joint with collars complete all as specified and directed.

Taking out existing water proofing treatment including cement plaster(any no of layers) on roof surfaces, cleaning the surfaces and removing the debris outside MOD land complete all as specified and as directed.

Supply only Liquid water proofing compound .

M/L for cleaning the plastered / concrete surfaces with wire brushes and applying water proofing treatment as under :- (a) Provide 10 mm thick plaster in CM (1:6) even and smooth without using extra cement. (b) Apply one coat of oil bituminous primer @ 0.20 kg/Sqm over concrete surface. (c) Laying APP Polimerised modfied membrane not less than 3 mm thick and weighing not less than 3.5 kg per Sqm by torch applicaton method. (d) The overlap for APP membrane shall be 75 mm on longitudinal direction and 100 mm on transverse direction (e) Finally applying a coat of solar reflective bitumiious aluminium paint @ 0.15 Kg/Sqm over the membrane. (f) The make / treatment shall be from the one of the following manufacturer:- (i) 'Moply FP' of M/s Texsa (I) Pvt Ltd. (ii) 'Hyperplast' pf IWL India Ltd. (iii) 'Super thermpay' manufactured by M/s Shalimar tar product. (iv) 'Hydroflame' of M/s Hydrotech Ltd.

M & L for 75mm thick cement concrete type D-2 1:4:8 (40mm graded aggregate) in sub base complete all as specified and as directed.

M & L for precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment over 25 mm thick sand cushion complete all as specified and as directed.

M & L PCC 1:2:4 type B1 (20 mm graded aggregate) as in bed blocks,copings,benching , kerb stone etc.

Taking down carefully copper/aluminium point wiring (light/exhaust fan) complete,(fittings such as switches, ceiling roses,pendants etc. to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc.

Taking down unserviceable main switches,DBs alongwith teak wood boards etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified.

M&L for point wiring complete including single core PVC insulated and unsheathed type flexible bright unsheathed multi stranded 1.5 sqmm copper conductor FR PVC casing caping and surface/concealed PVC Conduit & accessories having ISI mark to be fixed with proper screws including all accessories/ fittings/ junction boxes /inspection covers etc including hard PVC board of required size fixed with wall surface including 1.5 sqmm 1100 V grade PVC insulated, unsheathed flexible muliti stranded copper conductor FR cable as continuous earthwire connected to metallic bodies of luminaries/fans etc. at one end and to common earth dolly at other end.

One light point controlled by one one way switch

One exhaust fan point controlled by one one way switch

One switch socket 5 pin 5 Amps flush type on same board.

S&F submain wiring with 2 single core PVC insulated multistranded flexible copper conductor 1100 Volts grade cables 4 Sqmm and 1 run 1.5 Sq mm Earth Wire PVC insulated multistrand cupper conductor cable (FR) drawn through PVC casing caping of suitable size and with all accessories all as directed and specified by Engr-In-charge.

S & F Switch piano flush type single pole one way 230V 6Amps

S & F ceiling rose surface three terminals ,230 Volts

S & F socket outlet 2-in-1, 3 pin 5 Amps.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply & fix LED tube light along with fixture, 20 W

Supply and fix LED building security light 35/36 W IP 65

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m

M & L in repair MCB DB SPN sheet metal double door enclosure mounted on teak wood board of suitable size for mounting MCB 230 Volts , 4 way

S & F MCB SPN 10-40 amps, 240Volts 10KA

S & F MCB SP 5-40 amps, 240Volts 10KA

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core

M & L for earthing complete with galvanised steel earth plate electrode 60cm ×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel,earth wire protected by GI pipe 15 mm dia 'light grade' including charcoal dust, common salt, excavation & earth work, PCC Pit with 1:3:6 type C-1, 40 mm thick RCC cover in 1:2:4 type B-1 reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with MS handles 12 mm dia, PGI funnel & GI watering pipe 'light grade' 20 mm bore all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Supply and laying GI galvanized, “Medium class” Pipe including fittings of following size.

25 mm dia

40 mm dia

S&F Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe of 20 mm dia.

S&F stop Valve, screwed both end for iron pipe or for unions and fixed, 25 mm fancy type.

Demolition of brick work or stone boulders masonary built in cement mortar including all quoins,arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles.

Dismantling plain or corrugated steel sheeting any gauge, any thickness including Nainital or similar pattern roof covering , in wall clading and valley gutters complete all as specified and directed.

Demolition of reinforced cement concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for .

Dismantling unframed timber in fillets,rafters,purlins etc. under 40 sqcm in section unframed work

M&L for brick work in burnt bricks with sub class 'B' bricks (old size) straight or curved on plain exc. 6m mean radius built in CM 1:6 allas specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

S&F Pre- painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

M&L for vitrified ceramic tiles 8-10mm thick, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36sqm in floors etc. set and jointed in neat cement slurry and pointed in white or cloloured cement to match incl screed bed of mortar 15 mm thick for laying floor finishes in CM 1:6 complete

All as per item No 90 but on skirtings incl 10 mm th rendering in CM (1:4) complete all as specified and as directed.

M & L for providing reinforced cement concrete Type B1 in 1:2:4 , using 20 mm graded stone aggregate, as in chajjas and the like complete all as specified and directed.

M & L for providing reinforced cement concrete Type B1 in 1:2:4 , using 20 mm graded stone aggregate, as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per item No 94 above but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders

M & L 75 mm thk Cement conc type C-2, 1:3:6 (40 mm gr agg) as in plinth protection finished even and fair .

M&L rolled sections as in main and cross beams, hip rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed witjh angle cleats or other connecting plates Fe 410 W (gde E 250 ) quality A including a shop coat of zink chromate primer complete all as specified and as directed.

M&L for MS work as in wind tie or any other work incl cutting , drilling holes etc.

Taking down chowkats or frames with shutters ( without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 sqm each.

Taking down steel window of any size compelte all as specified and directed.

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 125 X 60mm.

M&L for PCC 1:3:6 type C1 in door frame filling all as specified and directed.

S & F for 35mm thick 2nd class hard woodplain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

Cutting holes in stone walls built in cement mortar for inserting hold fast/lugs & making good disturbed portion in CM 1:3 or cement congrete 1:2:4, type B-1 as required (Depth of embedded portion of hold fasts orings measured from the face of the jamb into wall exc half brick but no exc one brick.

Supply and fixing three track sliding window including frame with two shutters with 4mm thick tinted glass and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips etc; fabricated using following aluminium anodised sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engineer-in-Charge. (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352. (Note:- Cost of Tinted glass & wire cloth shall be included in the quoted rate of the item).

S & F Aluminium powder coted decogrill 7.5mm width and 6mm thk of design DG 102 having weight 3.131kg/Sqm fixed to and including powder coated aluminium U type frame with CP brass/SS screws @ 200 c/c, including cutting the grill to proper opening size for fixing and operation of handle and fixing powder coated aluminium section around the opening all as per requirement and direction of Engr-in-Charge

M&L for Marble work green marble 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade incl screed bed or bedding layer of mortar 15m thk in CM 1:6 complete all as specified.

S&F stainless steel wirecloth 0.36 mm nominal dia of wire and average aperture 1.40 mm and fixed with stanless steel wire staples.

S&F 4.0 mm th sheet glass ordinary quality plain and glazing with oil putty in square n'exc .5 sqm in each pane.

S & F of 150 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and directed.

S&F 125 mm MS, Butt hinges,medium weight cold rolled fixed with screw or welding complete.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L for rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick work or conrete wall surfaces finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound.

M&L Rendering 10 mm thick in cement mortar (1:6) on concrete surfaces/brick wall surface, finished even and smooth without using extra cement complete all as specified.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.complete all as specified and directed. Make of Arcylic emulsion weather coat paint :- Asian (Apex Ultima) ,Berger (Super coat ) or ICI Dulux (weather shield) .Make of primer :- Asian (X2) or Equivalent . Note:- (a) Each stage i.e. preparation of surfaces, application of primer, application of first coat, application of second coat will be got passed from Engr-in -Charge.(b)Written Warranty for four years or as per manufacturer's instructions, whichever is more is required to be furnished by contractor for this item.

M&L for preparation of new plastered surfaces & applying two coats of oil bound Distemper over a coat chalk whiteing on walls.

M & L for preparation of new wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth & applying 2 coats of synthetic enamel paint over a coat of red oxide primer.

S&F in repairs stainless steel curtain rod 25 mm dia complete with bracket and side knobs all as specified and directed.

Dismantling wall & ceilling boards(fibre pulp insulation etc) or insulation boards/ slabs/blankets, any thickness including cover fillets complete all as specified and as directed.

S & F Aluminium anodised snap grid false ceiling, for insulation and acoustic purpose, using standard aluminium sections of size 35.60mm 23.60mm x 1.6 mm as in wall angle, 23.60 mm x 23.60 mm x 1.60mm as in main/cross tees and 26.00mm x 26.00 mm x 1.60mm angles for grid of size 605 x 605mm suspended wth 4mm dia GI wire at intervals n exc. 600 mm centre to centre and fixed to roof truss with sitable size MS hooks and fastening bolts etc from sloping flat roof including 12mm thk Gypsum ceiling boards of size 600 x 600mm fixed with clips to aluminium snap grid including preparation of exposed surfaces of ceiling boards and applying two coats of acrylic emulsion distemper over a coat of primer all as specified and as directed

M & L for Chequered cement concrete tiles of 20 cm x 20cm x 25 mm thick with grey cement and pigment,set and jointed in neat cement slurry in floors including 15 mm thick screed bed or bedding layers in cement mortar 1:6 for laying tiles complete all as specified and as directed.

M&L for consealed point wiring for One Light/Bell point controlled by one switch, complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 V grade confirming to IS 694 drwan through PVC conduit of suitable size heavy grade ISI marked including necessary conduit accessories, sunken type pressed steel terminal boxes with plastic laminated sheet of approved shade 3mm thick including 1.5 mm PVC insulated FRLSH copper conductor as in continious earth wire for:

All as item No 124 here in before but one ceiling / Exhaust fan point controlled by one switch

All as item No-124 here in before but one 3 pin 5 Amps socket outlet on independent board

All as item No 124 here in before but one 3 pin 5 Amps socket outlet on same board

All as item no-1 here in before but one but with 4 Sqmm wire for 15 Amp socket outlet on independent board.

M&L for submain wiring with 2 single core PVC insulated multistranded flexible copper conductor 1100Volts grade (FRLSH) cables 4.sqmm and 1 run 4 Sq mm PVC insulated multistrand copper conductor cable (FRLSH) of green colour for continious earthing drawn through PVC concealed PVC conduit of suitable size and with all accessories all as directed and specified by Engr-In-charge.( Note: Two runs of 4 sqmm, one run of 4 sqmm copper conductor and one run of surface/concealed PVC conduit of suitable size and with all necessary fixing accessories and making good disturbed surface area shall be measured as one length.)

S & F Switch modular type single pole one way 230V 6Amps

S & F Socket outlet 2 in 1 , 3 pin 5 Amps modular type 230V S.P. multipurpose type

S& lamp holder PVC/Polycarbonate type with back plate suitable for battern fittings

S & F ceiling rose surface PVC 50 mm dia three terminals including PVC mounting block, white/lvoury /Urea finish.

M&L in repair for stepped type electronic fan regulator flush type on the existin phenolic laminated sheet etc as required for ceiling fan 230 volt AC supply, 50HZ 1200/1400 mm sweep

M & L MCB DB SPN sheet metal double door enclosure mounted on teak wood board of suitable size for mounting MCB 240 Volts with 200 Amps rated bus bar 8 way

S & F MCB SP 6-32 amps, 240Volts 10KA

S & F MCB SPN 32 amps, 240Volts 10KA

Supply & fix LED tube light along with fixture, 30 W

Supply & fix LED lamp fittings along with fixture, 12 W

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor alongwith hanginghook/clamp.

M & L for earthing complete with galvanised steel earth plate electrode 60cm ×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel,earth wire protected by GI pipe 15 mm dia 'light grade' including charcoal dust, common salt, excavation & earth work, PCC Pit with 1:3:6 type C-1, 40 mm thick RCC cover in 1:2:4 type B-1 reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with MS handles 12 mm dia, PGI funnel & GI watering pipe 'light grade' 20 mm bore all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Supply, laying, jointing, testing and commisioning XLPE cable 1100 Volts grade PVC insulated armoured and PVC sheathed with stranded aluminium conductor heavy duty ISI marked incl cable glands lugs bolts nuts washers etc to suit the cable size to be laid in trenches fixed along pole, LT panel floor bore or through GI pipe laid under floors, fixed, concealed in wall encased in GI pipe etc complete of following sizes incl taking down old unserviceable over head conductors and insulators channels carefully as directed by Engr-in-Charge:-

16 Sqmm x 2 Core

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out

(a) Soft/Loose Soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M & L for High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 size of 40mm dia

Earth work in excavation all kind of soil by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

M & L Plain Cement concrete in sub bases/pavings Type D2 1:4:8 (40mm graded aggregate) all as specified and directed.

M&L for PCC (1:3:6) Type C-2 (40mm graded aggregate) as in surface channels and drains complete all as specified.

M&L for brick with fly ash brick old size straight of curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 including finishing the surface even and smooth without using extra cement complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

M&L for Removing excavated soils n.exc50m and depositing where directed at a level n.exc 1.5m above the starting point.

Extra for forming fair finished drain or channel 70 cm inner grith in cement concrete with using extra cement incl. forms moulds, mitred / stoped ends

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate as in coping including weathering throating and necessary formwork complete all as specified.

M&L for pre cast cement concre type B1, 1:2:4 (20mm graded stone agg) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete.

M&L 300 mm Dai cement concrete 1:3:6 type C-2 Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested;

M&L 300 mm Dia Salt-glazed stoneware drain pipes laid in trenches and jointed as specified

S Y Itkar Construction and Company (BID ID -3510997)

KARPE AND SONS CONSTRUCTION (BID ID -3506193)