Construction of Sub Zonal office at Bhat Village, Gandhinagar, for Gandhinagar Municipal Corporation.(2nd Trial)

Name of Work : - Estimate For Construction of Sub Zonal office Bhat Village, Gandhinagar, for Gandhinagar Municipal Corporation

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials

Rupees One Hundred Twenty

1 and disposing of the excavated stuff upto 50meter lead any kind of soil. Cumt 497.00 123.13

Three and Thirteen Paise Only

Excavation for foundation 1.5 to 3.0 m depth including sorting out and stacking of useful

Rupees One Hundred Seventy

2 materials and disposing of the excavated stuff upto 50meter lead any kind of soil. Cumt 497.00 170.50

and Fifty Paise Only

Filling available excavated earth (excluding rock)in trenches, plinth, sides of foundations etc. in

layers not exceeding 20cm in depth consolidating each deposited layer by ramming & watering. Rupees One Hundred Thirty Six

and Ninety Two Paise Only

Disposing of the surplus excavated earth and/or debris etc. including loading at site, transporting

& disposal, unloading, spreading and dressing etc. complete with all leads & lift, as directed

anywhere out side plot boundary. Site for disposing (non objectional place) to be found and Rupees One Hundred One and

selected by the contractor all as per specifications and direction of Engineer-in-charge. upto any Forty Four Paise Only

lead any kind of soil. A) upto 5km

Filling in foundation and plinth with murrum or selected soil in layer of 20cm thickness including

Rupees Two Hundred Seventy

5 watering ramming and consolidating etc. complete. Cumt 952.00 277.14

Seven and Fourteen Paise Only

Filling in plinth with sand under floors including watering ,ramming , consolidating and dressing Rupees Four Hundred Eighty

6 etc. complete. Cumt 37.00 481.70

One and Seventy Paise Only

Providing and laying controlled cement concrete work M150 and curing complete including the Rupees Four Thousand Four

7 cost of form work but excluding the cost of reinforcement of reinforced concrete work in Cumt 85.00 4458.14 Hundred Fifty Eight and

foundation and plinth. Fourteen Paise Only

Providing and laying cement concrete 1:3:6 (1 cement : 3coarse sand :6 graded stone aggregates

20 mm nominal size) and curing complete excluding cost of formwork in(A) Foundation and plinth Rupees Three Thousand Eighty

Four and Eighty Nine Paise Only

Providing and laying controlled cement concrete work M250 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Rupees Four Thousand Nine

9 foundation, footings base of column and mass concrete. (A) Footing (Design Mix or RMC can be Cumt 236.00 4931.83 Hundred Thirty One and Eighty

use as directed by EIC/PMC. No Extra Rate can be paid) Three Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and laying controlled cement concrete work M250 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Column Rupees Eight Thousand Two

10 ( B) Column up to all floor level (Design Mix or RMC can be use as directed by EIC/PMC. No Extra Cumt 66.00 8246.65 Hundred Forty Six and Sixty

Rate can be paid) Five Paise Only

Providing and laying controlled cement concrete work M250 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Beams. Rupees Five Thousand Nine

11 (C) Ground Beams and plinth beams. (Design Mix or RMC can be use as directed by EIC/PMC. No Cumt 52.00 5989.30 Hundred Eighty Nine and Thirty

Extra Rate can be paid) Paise Only

Providing and laying controlled cement concrete work M250 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Floor Rupees Six Thousand Four

12 Beams. (D) Floor Beams. up to all floor level (Design Mix or RMC can be use as directed by Cumt 35.00 6482.90 Hundred Eighty Two and

EIC/PMC. No Extra Rate can be paid) Ninety Paise Only

Providing and laying controlled cement concrete work M250 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Slabs. (E Rupees Six Thousand Six

13 ) Slab up to all floor level (Design Mix or RMC can be use as directed by EIC/PMC. No Extra Rate Cumt 83.00 6666.72 Hundred Sixty Six and Seventy

can be paid) Two Paise Only

Providing and laying controlled cement concrete work M250 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Rupees Eight Thousand Forty

14 Staircase. (F ) Staircase up to all floor level (Design Mix or RMC can be use as directed by Cumt 10.00 8042.99

Two and Ninety Nine Paise Only

EIC/PMC. No Extra Rate can be paid)

Providing and laying controlled cement concrete work M200 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Lintel or Rupees Six Thousand Three

15 Copping. (G ) Lintels up to all floor level (Design Mix or RMC can be use as directed by EIC/PMC. Cumt 30.00 6371.80 Hundred Seventy One and

No Extra Rate can be paid) Eighty Paise Only

Providing and laying controlled cement concrete work M200 and curing complete including the

cost of form work but excluding the cost of reinforcement of reinforced concrete work in Chajja. ( Rupees Six Thousand Two

16 H) chhajja up to all floor level (Design Mix or RMC can be use as directed by EIC/PMC. No Extra Cumt 6.00 6206.16 Hundred Six and Sixteen Paise

Rate can be paid) Only

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing

in position complete upto all floor level. Rupees Seventy Eight and

Thirty Four Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and constructing brick work using common burnt clay building bricks having crushing

Rupees Four Thousand Four

strength not less than 35 kg/sqcm. in cement mortar 1:5 (1 cement :5 fine sand) etc. comp.(B)

18 Cumt 354.00 4492.97 Hundred Ninety Two and

Conventional up to all Floor Level

Ninety Seven Paise Only

Half brick masonary in common burnt clay building brick having crushing strength not less than

kg/sq.cm. In cement mortar 1:4 ( 1 cement : 4 coarse sand ) (B) Conventional up to all Floor Level Rupees Six Hundred Seventy

Six and Fifty Two Paise Only

Providing 15mm. thick cement plaster in single coat on rough (similar) side of single or half brick

walls for interior plastering up to floor two level finished even and smooth in cement mortar 1:4 Rupees One Hundred Eighty

[1 cement: 4 sand) etc. complete up to all floor level Nine and Fifty Nine Paise Only

Providing & laying 10 mm. thick cement plaster in single coat on fair side of brick concrete walls

& ceilings for interior plastering upto floor two level and finishing with smooth mala plaster.(i) Rupees One Hundred Eighty

Cement mortar 1:3 (1 cement : 3 sand) up to all floor level Five and Ninety Two Paise Only

Providing 20 mm thick double coat mala cement plaster on interior brick/ concrete work for

plastering comprising of base coat of 12 mm thick cement plaster in cement mortar (1 Cement : 4 Rupees Three Hundred

22 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 ( 1 Cement : 2 Sqmt 1383.00 314.16 Fourteen and Sixteen Paise

coarse sand) finished with trovel including scaffolding curing etc. complete. up to all floor level Only

20mm. thick sand faced cement plaster on walls upto 10 meters above ground level consisting of

12mm thick backing coat of c.m. 1:3 (1 cement :3 sand ) and 8mm thick finishing coat of c.m. Rupees Three Hundred Fifteen

1:1(1 cement :1sand)etc. complete. and Sixty Nine Paise Only

Providing 20mm deep finished groove . etc.comp Rupees Forty Three and

Seventy Four Paise Only

Providing & Fixing the Chikenmesh - 20 guage(Crimp Jali) of approved size applying between the

RCC and masonry junction in proper line, level and plumb with all material, labour, tools, tackles Rupees Seventy Seven and

and equipment. Including providing and fixing the jali with nails, etc complete as directed by the Seventy Seven Paise Only

Applying two coats of Birla or Asian acrylic lappy (putty) and two coats of primer of approved

brand and manufacture on new wall surface to give an even shade including thoroughly brushing

the surface free from mortar dropping and other foreign matter and sand prepared smooth. and

Rupees One Hundred Twenty

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on

26 Sqmt 2628.00 123.78 Three and Seventy Eight Paise

undecorated wall surface to give an even shade including throughly brushing the surface free

from mortar droppings and other foreign matter and sand papered smooth.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an

required shape even shade after thoroughly brushing the surface to remove all dirt, and remains Rupees One Hundred Twenty

of loose powdered materials.etc complete and Twenty Six Paise Only

Texture paint :Wall painting two coats with Stucco of Asian or equivalent approved brand in any

shades and colour as directed on wall surface to give an even shade including applying of a one

coat of Penetrating prmer or equivalent and two coats of paint, scaffolding to at any height with

all labour and material thoroughly brushing the surface free from mortar droppings and other

foreign matter and sand prepared smooth etc. complete. The substrate must be sound, clean,

dry, free from dust, oil, grease and laitance etc. All traces of release agents must be removed. On Rupees One Thousand Six

28 chalky and dusty surfaces, all loose material must be removed by stiff bristle brushing. The primer Sqmt 1383.00 1644.28 Hundred Forty Four and

/ paint application is to be done with the rollers. rate shall be including crack filling and levelling Twenty Eight Paise Only

as per manufacturers specfication. Top coat should have. 1) Low VOC content. 2) Crack Bridging

ability upto 2.6 mm. 3) 100% pure acrylic emulsion 4) Anti-Carbonation concrete protection 5)

Very Low Flame spread 6) Superior Washability

Providing and laying Granite Slab 18mm thick thick in flooring treads of steps and landing laid on

Rupees Two Thousand Seven

a bed of 12mm thick cement mortar 1:6 (1-Cement : 6-Coarse Sand) finishing with full molded

29 Sqmt 59.00 2797.70 Hundred Ninety Seven and

round edges, flush pointing in white or colour cement.

Seventy Paise Only

Providing and laying polished Granite Slab 18mm thick in Risers of steps Dedo, window sill, jembs

and pillars laid 10mm thick Cement Mortar 1:4 (1-Cement : 4-Coarse Sand) and jointed with Grey Rupees Three Thousand One

30 Cement Slurry including full molded round front edges , rubbing and polishing etc. complete. Sqmt 166.00 3145.14 Hundred Forty Five and

Fourteen Paise Only

Proving and fixing 18mm th. Both side Mirror Polished black granite of approved quality full

molded round front edge as urinal partition and wash basin counter fixed with wall in cement

Rupees Two Thousand Eight

mortar 1:3 including rubbing and polishing with necessary bonding with adhesive etc. complete.

31 Sqmt 17.00 2824.97 Hundred Twenty Four and

(Both edges are round in shape with polishing)

Ninety Seven Paise Only

Providing and laying polished kota stone slab flooring over 20 mm.(average) thick base of

cement mortar 1:6 (1 cement : 6 coarse sand) or L.M. 1:1.5 laid over and jointed with gray Rupees One Thousand

32 cement slurry including rubbing & polishing etc. complete. [A] 25mm Sqmt 27.00 1019.39 Nineteen and Thirty Nine Paise

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and laying polished kota stone slab 25mm thick in risers of steps,skirting Dedo and

pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray Rupees One Thousand Two

33 cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. Sqmt 3.00 1226.46 Hundred Twenty Six and Forty

complete. Six Paise Only

Providing & Laying 600x600mm/ 800 x800mm/ 600 x1200mm/ 800 x1600mm vitrified 8 mm to

10 mm thick tile flooring over 40 mm bedding(average ) base of cement mortar 1:6 (1 cement : 6 Rupees One Thousand Five

34 Coarse sand) or L.M 1:1.5 laid on new surface flooring and jointed with white cement slurry Sqmt 671.00 1531.82 Hundred Thirty One and Eighty

including finished with flush pointing & cleaning the surface etc.completed for light shed/ Dark Two Paise Only

Providing and laying vitrified tiles 8mm to 10mm thick in skirting,risers of steps and dedo on Rupees One Thousand One

35 10mm thick cement plaster 1:3 (1 cement : 3 Coarse sand) & jointed with white cement Sqmt 29.00 1114.09 Hundred Fourteen and Nine

slurry for light shed satin finish/Semi glossy. Paise Only

providing and laying coloured vitrified tiles of the size 300x 600mm/ 300x 450mm / 600x 600mm

/ 600x 1200mm/ 800x800mm/ 800x 1600mm 8-10mm Thick in skirting, risers of steps and dedo Rupees One Thousand Five

36 on 10mm. Thick cement plaster 1:3 (1 cement : 3 coarse sand) & joined with white and color Sqmt 224.00 1513.28 Hundred Thirteen and Twenty

cement slurry. Eight Paise Only

Spacer/Groove in Flooring and Dedo/ skirting Approved Quality 5mm Th & Filled Approved epoxy

Grout, Providing and applying epoxy Grout in the tiles joint of size 6mm width and 10mm depth.

The grout is in the powder form to be mixed in the ratio of : each one kg of grout requires 175 ml Rupees Eighty Five and Eighty

of water and 100 ml of Ardex Endura Admix GT1, polymer additive to enhance the strength of Five Paise Only

Providing & Fixing toilet partition with 45mm round ss bar or square ss tube 304 & 12mm hpl

Rupees Six Thousand One

(High Pressure Laminates) sheet both side plain surface and with all standard fittings. incuding SS

38 Sqmt 44.00 6140.80 Hundred Forty and Eighty

make all hardwares, first quality locks, stopper, handles etc. complete.

Providing and fixing flush door both sides laminated shutter fabricated from 35 mm thick solid

core malemine faced three layered pre laminated flat pressed wood based exterior grade bonded

BWP/BWR synthetic resin having stamped IS 12823 grade I type II including three coats of Rupees Five Thousand Five

39 lacquer polishing to exposed wooden surfaces and Stainless steel decorative type designs Sqmt 53.00 5513.59 Hundred Thirteen and Fifty

fixtures / fastening Cylindrical/ Mortise Locks, towerbolt etc.including I.T.W. triangular batten Nine Paise Only

patti of size 30m.m.x30m.m.etc. as per architectural detailed drawing and as directed by engineer

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and fixing FRP FRAME size 100 x 50mm and 28mm thick FRP depress pannel shutter

having extra reinforcement on sides and edges and in gel coat finish. The core of the shutter is to

be filled up with injected fire retardent grade polyurethane foam done in situ along with

embedded wooden places for stiffening and also for tacking hinges and fixture. The hole FRP Rupees Two Thousand Three

40 frame and shutter is to be water proof, water proof, termite proof and resistance to mild Sqmt 7.00 2377.76 Hundred Seventy Seven and

acid/Alkali. Rates are to be inclusive of S.S hinges with necessary screws and Alluminium fixture Seventy Six Paise Only

and fastening.Product should have 3 years prefomance guarantee and company have ISO 9001-

2000 certificate.

Window Two Track:Supply & Fixing of Aluminium Sliding window With side fix glazing using

partition profile & top partition sliding Domal series section - Shutter 66 x 26x 1.4 mm , Track 45 x

45x 1.5 mm , Interlock clip - 37 x 37x 1.4 mm , Intermediate frame - 47.5 x 44.5 x 1.4 mm . LAVAL

or equivalent brand bearing with 2 point locking system with projected handle with 5mm Thick Rupees Five Thousand Five

41 Toughned glass (glass with good quality EPDN gasket of good quality(i.e. osaka,maharastra Sqmt 22.00 5555.00

Hundred Fifty Five Only

Rubber over back type ) with silicon lining on prephery. as per sample approval by Architect. work

complete including all type of hardware, fittings , fixtures etc complete as per detailed drawings,

sample mock and specifications.

Window Three Track:Supply & Fixing of Aluminium Sliding window With side fix glazing using

partition profile & top partition sliding Domal series section - Shutter 66 x 26x 1.4 mm , Track 65 x

45x 1.5 mm , Interlock clip - 37 x 37x 1.4 mm , Intermediate frame - 47.5 x 44.5 x 1.4 mm . LAVAL

or equivalent brand bearing with 2 point locking system with projected handle with 5mm Thick

42 Toudged glass (glass with good quality EPDN gasket of good quality(i.e. osaka,maharastra Rubber Sqmt 52.00 6060.00 Rupees Six Thousand Sixty Only

over back type ) with silicon lining on prephery. as per sample approval by Architect. work

complete including all type of hardware, fittings , fixtures etc complete as per detailed drawings,

sample mock and specifications.

Providing, fabricating and fixing in position aluminium section for doors, windows, vent, sun

breakers, facade etc. as per approved shop drawings and aluminum sections of approved make

like Jindal or equivalent of 20microns colour anodize approved shade sections all floors, all levels,

all heights, all shapes and for all sizes as per the drawing, specification or as directed by Architect

or Engineer - in - Charge . Rate shall be inclusive of providing aluminium sections (conventional or Rupees Five Hundred Thirty

43 Euro-profile), Rate should include complete finished item with necessary assessories, hardware Kg 88.00 534.29 Four and Twenty Nine Paise

and other requirements. Work shall have to be carried out as per the approved shop drawings Only

and approved sample. All the aluminium section will be considered under this item with all the

necessary assessories, hardware only shall be paid extra. Payment shall be done as per

drawing/laid at site, glass, panels shall be paid in relevant tender items.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Fabricating, supplying and fixing in position SS daso for staircase and balcony with brush finish

and 304 grade as per Indian Standrd and detailed drawing including grinding, cleaning and filling Rupees One Thousand Nine

44 the welded spots with SS finish (Only Length will be paid for payment ). The Work to be executed Rmt 40.00 1901.83 Hundred One and Eighty Three

as per consultant drawing . Paise Only

Providing and fixing M.S. ORNAMENTAL GRILLS of required pattern with at required spacings and

frame alround, square or round bars, in columns, beams and joists, channels, MS flat, Angles,

Pipes, tees flats with connecting plates or angle cleats Steel work welded, in built up sections

Rupees One Hundred Fifty

45 framed work including cutting, hoisting, fixing in position and with one coat primer & two coat oil Kg 2270.00 157.56

Seven and Fifty Six Paise Only

paint as per detail drawings etc. complete. at any lead and lift etc. complete. As directed by EIC.

Fabricating, supplying and fixing in position SS railing for staircase and balcony with brush finish

and 304 grade as per Indian Standrd and detailed drawing including grinding, cleaning and filling Rupees Three Thousand Four

46 the welded spots with SS finish (Only Length will be paid for payment heigth max.1.0 mt.). The Rmt 35.00 3415.82 Hundred Fifteen and Eighty

Work to be executed as per consultant drawing . Two Paise Only

Supply & fixing and bending of Aluminium Composite Panel (ACP), 4 mm thick of brand Aludecor,

aulomax, Alstrongetcin required colours for exteriors consisting of two layers of aluminium skins

of 0.50 mm thick sandwiching a thermo plastic core in continuous lamination process with PVDF

coating for exterior grades ensuring long colour and no fungal attacks. With Base frame work

with aluminium sections of 50mm X 25mm of 1.5 mm thk and should be of Jindal / Hindalco or (IS

spec) brand,shall be fixed over the fabricated grid of 75 X 75 X 4 mm HSS pipe with not less than

thickness of 4 mm as per drawing, and the above aluminium panels shall be fixed to the frame Rupees Two Thousand One

47 work as cladding with material:- 3M tape and silicone dowcorring 789weather silicone in 995 Sqmt 50.00 2121.00

Hundred Twenty One Only

dowcorring.Also provide the Cantex Jali behind the elevation treatment. Rates includes cost of

labour,Bending of ACP, accessories, adhesives, scaffolding, wastages, transport, taxes, fixing into

a neat finish in aesthetic point of view, without any undulations in facias all complete and some

other miscellenous items not mentioned shall be as per the Instruction of engineer in-charge.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and fixing Structural Glazing with using the 17 Micron anodised of approved colour

alluminium section as transium, mullium of size 63.5mm x 38.1mm x 2 mm and sub frame of size

25mm x 50mm 1.6mm thick all coloure anodized of 15 microns. with using 5 mm thick toughened

super silver grey or. equivalent glass and fixed with silicone sealant and spacer tap and at corner Rupees Four Thousand Six

sealed neoprene foam dust and Air sealed gasket mirred including scaffolding etc.complete with Hundred Forty Six Only

all necessary fitting and fixtures for openable window as per Architectural drawing.

Wet Area Waterproofing : 1.Surface Preparation 1. Remove all loose material, grease, oil, dust

etc. from the surface on which the treatment is to be done.,2. All Vertical pipe penetrations must

be firmly grouted and an angle fillet must be formed around it. 3. Spilled concrete or other

material should be cut back to sound concrete and made good with suitable cementitious repair

mortar (Deucrete CWP or equivalent).2 : 3 Coat Cementitious Waterproofing System (Primer +

Coats) (Deucrete CWP, Pidilite , Bal Endura or Equivalent) Once the surface is prepared as per the

requirement, Damp down the concrete surface with clean water. 2. Whilst damp, but free from

standing water, apply using a short, stiff bristle brush or roller. For heavy 6-10 mm depressions,

etc. use less gauging liquid and mix to the desired consistency. 3. A first primer coat of

waterproofing chemical Deucrete CWP (or Equivalent), mixed with water, cement and sand in the Rupees Seven Hundred Fifty

ratio of 1:1:1:1 is applied to the floor and walls. 4. After the primer coat dries, a second coat with Seven and Fifty Paise Only

the ratio of 1:1:1 (Deucrete CWP/Pidilite/ Bal Endura : Cement: Sand) is applied at an average

consumption of waterproofing material at 2 Kg/M². 5. Once the second coat is dry, Third coat is

applied at the same rate and ratio. Ponding Test 1. Once the Waterproofing work is finished and

dried (confirmed by the site supervisor), ponding test must be conducted by filling the entire wet

area with water. 2. Once ponding test is certified with absence of any kind of leakage or

dampness, further work must be commenced.Work complete including all type of tools , tackles,

scaffolding etc complete at any level and height. work complete as per the instuction of

EIC/Client/Architect.

IPS : Providing and laying cement concrete flooring 1:2:4 (1- cement : 2-coarse sand : 4-graded

stone aggregate 20mm nominal size) laid in one layer and finished with a floating coat of neat Rupees Three Hundred Sixty

cement. (B) 50mm thick. Nine and Thirteen Paise Only

Terrace Tiles Work : Providing and laying Lapato/ Matt / Non skid,/Rustic finish/ Vitrified tiles in

using minimum 12 mm thick tiles as per approved make list by architect /client (size 400 mm

X400mm) fixed in Floor on 20 mm th. Cement Mortar 1:3 (1 cement: 3 coarse sand) All surfaces

must be dimensionally stable according to IS 1443-1972, level, cured, undamaged,

compact,rigid,resistant, dry and free from any debonding agents tiles fixed by approved tile Rupees Nine Hundred Fifty

51 adhesive and all application shall be done under instruction of manufacturer guideline and Sqmt 271.00 959.50

Nine and Fifty Paise Only

specification , and jointed with 4m thick epoxy grouting as per approved make of approved shade

and colour in proper line and level as per detailed drawing / instruction all complete as per

approved sample by Architect, drawings and instruction of EIC. at all floors / all levels / all heights

and all shapes . Basic rate of tile is Rs. 80/Sq.ft

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

providing and laying brocken chine mosaic flooring for terrace using 12mm to 20mm brocken

pieces of glazed tiles to be laid over cement mortar 1:3 to plin or slope and to be tempered to

Rupees Seven Hundred Forty

bring mortar crème out up to surface using white cement including rounding of juctions and

52 Sqmt 40.00 747.29 Seven and Twenty Nine Paise

extending them up to 15 cm along the wall clearing with water and oxalic acid etc. directed.

Constructing of Under Ground water tank with Providing and laying controlled cement concrete

M250 mix for R.C.C. work including rainforcement, boxing, centering, vibrating, curing and mixed

with approved water proofing cement compound or "CEMWET" or "PIDICRETE LW" integral

water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall be as

recommended by the manufacture of the water proofing material, concrete work for top, bottom

slab & side pardi for under ground water tank item incl. Necessary excavation & refilling the Rupees Twelve and Sixty Five

53 available earth, 15 cm thk 1:3:6 for bedding of concrete, 20 mm thk. water proofing cement lit 50000.00 12.65

plaster in C.M. 1:3 with smooth finishing & Glazes tile Dedo, vata, watering etc. Comp. to all face

of tank . including locking arrengement outlet, inlet, overflow and washout outlet pipe

arrengement as necessary & C.I. Cover 0.60 x 0.45 weight not less then 35 kg with locking

arrengment. etc. comp as per structural drawing Including Steel & as directed by Eng-in-charge.

Signages : Providing and fixing signages comprising form ss plate with Vinyl film letter , MDf finish

or SS plate with 12 mm thick coloured glass as per instruction of Archiect/EIC. Contractor shall Rupees Eight Hundred Ninety

submit mock up sample. Eight and Ninety Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Logo Work : Providing and fixing standard Logo using virgin acrylic or other material like Colored

HDF/cementsheet /SS plate with CNC work complete as per architect selection , letters as per Rupees Five Thousand Six

55 detailed drawings and fixed with approved adhesive with necessary fittings and provision shall be Sqft 18.00 5635.80 Hundred Thirty Five and Eighty

made for conceal LED light as per detail drawing. Paise Only

Name work: Providing & Fixing of SS box type letters with CNC Cutting and thickness of 50mm

border supported with MS angle inside latter & fixing the angle in RCC or brickwork with

necessary clamps nut bolts SS must be 304 grade, powder coated and 2mm thickness letter size Rupees One Thousand Five

56 of 45cm height and approprite width illumination with liner lights in background etc completed Sqft 113.00 1530.15 Hundred Thirty and Fifteen

with all labour and material as per directed by architect and engineer incharge. Paise Only

WATER SUPPLY & SANITATION

Providing and fixing wash down water closet wall hung type pan ( CERA make COMPACT WITH

CARONA SEAT COVER 490 x 350 x 330 mm Cat No. : S1043152 Wall hung EWC with Twin flush Rupees Eleven Thousand Seven

57 cistern (Cat No. : B1020106) with P or S trap jointed with C.I. pipe in C.M 1:1 including C.I chair Each 16.00 11778.62 Hundred Seventy Eight and

bracket , matching seat cover , jet spray with all accessories ( Cera, Nycer, Hindware) etc. comp. Sixty Two Paise Only

as directed by engineer incharge.

Providing and fixing white colour Wall Hung washbasin(CANON Cat No. : S2040102 Wash basin

without pedestal 450 x 350 x 195 mm) with Cl or MS brackets painted white including cutting

holes, ranking bolts for fixing and marking good the same, including fixing C.P. Brass waste

coupling 32mm dia & 32mm dia rigid p.v.c. waste pipe & 15mm dia Pillar Cock (Jaguar make Rupees Five Thousand Seven

58 model no. COP-011PM) capstan head C.P. screwed dowen high pressure with screw shank and Each 10.00 5723.67 Hundred Twenty Three and

back nuts & rubber plugs, Angular Stop Cock with Wall Flange ( COP-057PM) with p.v.c. Sixty Seven Paise Only

connection pipe and testing the same for leak proof etc...., completed as per directed by E.I.C.

Providing and fixing CERA brand Urinal For Gents Toilet (CHRYS Cat No. : S4020103 Urinal 340 x

280 x 470 mm) & 15mm Angular Stop Cock with Wall Flange ( COP-057PM) of approved brand of Rupees Four Thousand Five

59 cera including connection the urinal with waste pipes in trap etc. complete as directed by Each 15.00 4590.45 Hundred Ninety and Forty Five

engineer in charge ( A) Urinal Flat Back 265 x 335 x 695 mm Paise Only

Providing and fixing C.P.towel ring of JAQUAR model no.ACN-1121N of approved ISI brand

Rupees One Thousand Six

quality, complete with C.P. brackets fixed to wooden pluges with C.P. screws testing the same…

60 Each 6.00 1664.48 Hundred Sixty Four and Forty

etc.,completed as per directed by E.I.C.

Eight Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing, and fixing Angular Stop Cock with Wall Flange (COP-057PM )of approved ISI brand Rupees One Thousand Two

61 quality, including fixing in Pipeline and testing the same… etc., completed as per directed by E.I.C.. Each 23.00 1220.08 Hundred Twenty and Eight

Providing and Fixing Long Body Bib Cock with wall flange (Jaquar Model No. COP-107PM or

Rupees Two Thousand Twenty

62 equivalent) etc., completed as per directed by E.I.C Each 24.00 2026.06

Six and Six Paise Only

Providing and fixing Soap dish holder of JAQUAR model no.ACN-1131N of approved ISI brand Rupees Nine Hundred Eighty

63 quality, complete with fixed to wooden pluges with C.P. screws testing the same… etc.,completed Each 6.00 987.78 Seven and Seventy Eight Paise

as per directed by E.I.C.. Only

Providing and fixing Soap Dispenser with Glass Bottle of JAQUAR model no.ACN1135N of Rupees One Thousand Seven

64 approved ISI brand quality, complete with fixed to wooden pluges with C.P. screws testing the Each 6.00 1737.20 Hundred Thirty Seven and

same… etc.,completed as per directed by E.I.C. Twenty Paise Only

Providing & fixing 600 mm. x 450 mm. bevelled edge mirror of superior glass at all floor levels,

mounted on 6 mm. th. A.C. sheet or plywood sheet & fixed to wooden plugs with C.P. brass Rupees Eight Hundred Fifty

screws and washers etc. for all floor Nine and Forty One Paise Only

Providing and fixing PVC SWR Nanhi trap IS 14735 for drain -100 mm diameter with jali of the

following nominal diameter of self cleaning design with C.I scead down or hinged grating Rupees Five Hundred Ninety

including the cost of cutting and making good the wall. Nine and Sixty Four Paise Only

Providing laying and jointing in true line and level following diameter U.P.V.C. SWR Type B pipe

conforming to IS 13592-1992 with one end plain and other end socketed with rubbering, & fitting

conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of Rupees Eight Hundred Seventy

67 the size 160 mm diameter x 210 mm length x 196 mm high at every 2000 mm center to center or Rmt 72.00 876.90

Six and Ninety Paise Only

shall be concealed in walls as directed including necessary fittings such as bends, shoes etc.

including testing of pies and joints and jointed with adhesive solvent cement including cost of all

materials A) 110mm Dia

Rupees Eight Hundred Thirty

Four and Thirty Eight Paise Only

providing & Fixing to wall ceiling and floor 10. kg F/Cm2 working pressure polythene pipes of the

following out side dia. Low densidy, complete with special falnge compression type fitting, wall Rupees Two Hundred Eighty

clipstec. Including making good the wall ceilling and floor (A) 75mm Dia and Twenty Three Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and fixing to wall ceiling and floor 10.0 Kg. /Sqcm working pressure polythelene pipes of

the following outside diameter, low density , complete with special flange compression type Rupees Three Hundred Thirty

fitting wall clipsetc. Making good wall ceiling and floor .(A) 110mm Dia Nine and Five Paise Only

Providing laying and jointing in true line and level following dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

help of clamp at every two metre C/C or shall be concealed as directed including necessary Rupees Seventy Two and Sixty

fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, Five Paise Only

including cost of all materials. (i) 15mm Dia.

(ii)25mm Dia Rupees Ninety One and Eighty

Four Paise Only

(iii) 40mm Rupees One Hundred Forty

Eight and Twelve Paise Only

Rupees One Hundred Ninety

Five and Sixty Seven Paise Only

Supplying & installing Brass Handle Ball Valve conforming to IS 778, of RB, Italy or equivalent. Ball

valve must be having screwed ends. The ball valve should be with stand with maximum pressure Rupees Two Hundred Five and

up to 16 Kg/cm2. Complete job as specified & directed. A) 15 mm Fifty Four Paise Only

Rupees Three Hundred Fifty

Eight and Eighty Five Paise Only

C) 40mm Rupees Eight Hundred Ninety

71.2 Each 12.00 893.24 Three and Twenty Four Paise

D) 50mm Rupees One Thousand Three

71.3 Each 2.00 1356.53 Hundred Fifty Six and Fifty

Three Paise Only

Providing and Fixing S.W. Gully trap with C.I. grating brick masonry chamber & water tight C.I Rupees One Thousand Two

72 Cover with frame of 300 mm x 300 mm size (inside) with standard weight. [1] square Each 5.00 1246.92 Hundred Forty Six and Ninety

mouth trap (B) 150 mm x 100 mm. size P or R -type Two Paise Only

Constructing Brick Masonry Chamber for underground C.I inspection chamber and bends with

bricks having crushing strength not less than 35 kg/sqm in CM 1:5 C.I cover with frame (Light

Duty) 455mm x 610mm internal dimension total weight of cover with frame to be not less than

38 kg (Weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab with 1:2:4 mix ( 1 cement : Rupees Two Thousand Nine

73 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:5:10 inside Each 4.00 2932.93 Hundred Thirty Two and Ninety

plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of Three Paise Only

neat cement on walls and bed concrete on walls and bed concrete, excavation etc. complete. (I)

Inside dimension 455mm x 610mm x 450mm deep for single pipe

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

(II) Inside dimension 500mm x 700mm x 450mm deep for pipeline one or two Rupees Three Thousand Six

74 Each 4.00 3660.76 Hundred Sixty and Seventy Six

Supplying and fixing reinforced concrete heavy duty nonpressure pipes with collars for culverts

including setting and joining the pipes in C.M. 1:2 watering and laying (to level or slope) of I.S. Rupees Six Hundred Seventy

class NP2 of following internal diameters.(i) 300mm dia. Five and Thirty Six Paise Only

supplying and fixing double coated PVC waer tank of syntex or ISI equivalant make including

delivery at site, supply and fixing of inlet,outlet,air vent overflow,ball cock,drainage sleeves of the

specified size, with necessary neo-prene gasket/ packing/ washer, GI washer & check nuts etc. Rupees Three and Ninety Five

76 complete as directed on terrsce, loft in bathrooms etc in any height. the rate shall include for lit. 11000.00 3.95

fixing additional accesories supplied by the accessories.

Providing & fixing Handicap toilet set (SKU: S1013200) with European Closet & wash basin & all

handicap requirement with dual flush tank, seat & lead (heavy duty) including C.I. Brackets, C.P.

brass hinges, M.S. / C.I. painted brackets, Waste Coupling, 32mm size bottle trap etc. all Internal

fittings complete with grab rails etc. rubber buffers, C.P nuts, bolts etc making holes in walls &

floors, & finishing for ready to use.The rate includes all necessary connection charges as per Rupees Fifty Nine Thousand

77 product detail to the satisfaction of engr. incharge where required & the final handing over etc. Nos 1.00 59963.70 Nine Hundred Sixty Three and

complete as per specifications, drawings and as directed by the Engineer-in-charge. (Make: Cera Seventy Paise Only

CRUSE SET - EWC 710 x 370 x 770 mm, Cat. No. S1013200, B1520118 Soft close seat cover,

S2040159 CRANE Wall hung wash basin 665 x 545 x 190 mm, F9030453 Single lever clinical

faucet, B2210106 Wall mounted grab bar 600 mm long 2nos, 2210108 Wall mounted hinged

hand rail 750 x

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling

and trees girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable Rupees Twenty Eight Thousand

78 materials (C) By mechanical means in area of light jungle 0.17 28455.09 Four Hundred Fifty Five and

Nine Paise Only

Boring hole 3.5m Deep in ordinary soil (for cast in situ piles)and getting out tosoil and disposal of

Rupees One Thousand Five

the surplus excaveted soil as directed within a lead of 50mtr for following diameter of pipes

79 Each 88.00 1561.19 Hundred Sixty One and

(iii)300mm Dia.

Nineteen Paise Only

Providing and fixing M.S. ORNAMENTAL GRILLS (entry gate/compoundwall grill) of required

pattern with at required spacings and frame alround, square or round bars, in columns, beams

and joists, channels, MS flat, Angles, Pipes, tees flats with connecting plates or angle cleats Steel

Rupees One Hundred Fifty

80 work welded, in built up sections framed work including cutting, hoisting, fixing in position and Nos 24800.00 157.56

Seven and Fifty Six Paise Only

with one coat primer & two coat oil paint as per detail drawings etc. complete. at any lead and lift

etc. complete. As directed by EIC.

Box cutting the road surface to proper slope and camber for making a base for road work

including removing the excavated stuff and depositing on the road side slope as directed upto Rupees One Hundred Nine and

50Mt.lead. Twenty Four Paise Only

Providing and laying Compacted WBM (Grade II) with BT crushed metal of size 40mm to 63mm)

including using 20% stone Screening grit 0.16 cum and stone dust 0.08 cum as filler including for Rupees Two Thousand Nine

82 Spreading, watering & consolidation by vibrator power road roller 8 tone to 12 tone etc complete Cumt 120.00 2988.59 Hundred Eighty Eight and Fifty

as per morth clause 404. Nine Paise Only

Providing & laying M-250 controlled cement concrete road using Trimix vaccum dewatering

system with providing and fixing & removing of "C" channel as per required level slope and

thickness of concrete and leveling and finishing the concrete using surface vibrator, power floater Rupees Six Thousand Eight and

and trowel light brooming on as directed including making joint Every using concrete cutter Forty Nine Paise Only

machine and Filling Joint with Bitumen etc. complete.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm

length,30cm height and 15cm thick of M250 grade concret as per approved design and including Rupees Three Hundred Seventy

84 excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc Rmt 427.00 374.92

Four and Ninety Two Paise Only

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with

grade of concrete M300 pnumatic compressed / vibrated mechanically and as per approved

design Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and filling the joint Rupees Seven Hundred Six and

with sand in proper line and level as per guidlines of IRC : SP 63-2018 etc. Complete. Ninety Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing, Laying & Spreding Good garden soil for Softscape works and plantation good earth at

site including royalty and carriage upto 5km etc completed as per direction by engineer in charge. Rupees Seven Hundred Fifty

Seven and Fifty Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Grassing: Grassing with selection No. 1 grass including watering and maintenance of the lawn

for 60 days or more till the grass forms a thick lawn, free from weeds and fit for mowing

Rupees Eighty Five and Eighty

87 including supplying good grass saplings, (if needed earth shall be paid for separately). In rows 5 Sqmt 150.00 85.85

Five Paise Only

cm apart in both directions

Plantation of Shrubs, and Hedge, bamboo, climber etc. at site i/c watering and removal of

unserveiceable material’s as per direction of officer in charge (excluding cost of plant ) Rupees Seven and Twenty Two

Plantation of Trees, at site i/c watering and removal of unserveiceable material’s as per

Rupees Twenty Three and

89 direction of officer in charge (excluding cost of plant ) Nos 70.00 23.11

Eleven Paise Only

Providing and stacking of Hibiscus rosasinensis, Hymenocallis littoralis, Ixora singaporensis,

Jasminum sambac, Nerium oleander (kaner) dwarf, Pandanus variegated dwarf,

Tabernaemontana coronaria dwarf, Vinca different colour and other varieties etc.... height 30-60 Rupees Ninety Five and Ninety

cm. multibranched in p.bag of size 25 cm as per direction of the officer-in-charge. Five Paise Only

Providing and stacking of Caesalpinia pulcherrima, Galphimia glauca, Jatropha pandurifolia,

Nerium oleander (kaner) white, Tecoa gaudichaudi, Thevetia peruviana and other varieties etc... Rupees One Hundred Twenty

91 height 60-75 cm. multibranched in p.bag of size 25 cm as per direction of the officer-in-charge. Nos 1500.00 126.25

Six and Twenty Five Paise Only

Providing and stacking of Champa Hybrid, Bambus, elonix regia (Gulmohar) , Plumeria acutifolia,

Tabebuia Rosea sp., Erythrina indica, assia fistula (Amaltash) , Cassia siamea, Lagerstroemia

flosreginae, Nauclea cadamba (Kadam) , Mimusops elengi (Maulsri) and other Tree veriety 25in Rupees One Hundred Eighty

x25in, well branched, established & free from disease at site as per direction of the officer-in- One and Eighty Paise Only

Providing and Displaying Bismarckia Palm & Washingtonia palm and other 4-6 ft ht., well

developed 12 and above good color fresh and healthy leaves in bag as per direction of the officer- Rupees Two Thousand Twenty

in-charge. Only

Providing and Displaying Bottle palm, Foxtail palm, Champion palm and other 10-12 ft ht., well

94 developed 12 and above good color fresh and healthy leaves in bag as per direction of the officer- Nos 0.00 606.00 Rupees Six Hundred Six Only

Interior and Furniture work

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

False Ceiling: Gypsum Board

Providing and Fixing Single Layer gypsum board 12.5mm thick of the make Newgood group Co

limited or equivalent & section using board of size 1220mm x 1830mm x 8mm suspended by GI

suapander of size 25mm x 3mm with intermidiate channle of size 18mm x 40mm x .8mm at

Rupees Six Hundred Six and

95 1220mm center to center ceiling section of size 40mm x 35mm x 0.55mm at 457mm center to Sqmt 100.00 606.95

Ninety Five Paise Only

center and perimeter chanel A of size 20mm x 27mm x 30mm x 0.5mm edges & drops including

paper tap sand sofit cleat, anchor fastener, soch bolt connecting cleant joining compound top

coat on ceiling including making necessary opening for light fitting, diffuser etc. complete as per

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular edge &

mmThick Densified edges on the Tile Periphery for Extra Strength The Light weight calcium silicate ceiling

tiles shall have , light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity resistance and

also having thermal conductivity0.043° w/m KC.for the best thermal Insulation. The Light weight calcium

Silicate tile shall be of approved texture Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & Globe

having NRC value of 0.75 NRC or equivalent of size 595 X 595 mm to be laid on true horizontal level

suspended inter locking metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm

including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and size of

24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size

24X28mm made out of 0.33mm(Minimum) sheet spaced 1200mmalong spaced between main ‘T’ at 600mm

centre to centre to form agrid of 1200X600mm and secondary cross ’T’ of length 600mm and size 24x28mm

made of 0.30 mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid

of size 600X600mm resting on periphery walls/partitions on a perimeter wall angle pre-coated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to

centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges light

weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the grid Rupees One Thousand Six

96 including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors Sqmt 56.00 1674.15 Hundred Seventy Four and

etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size Fifteen Paise Only

25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mmlong dash fasteners, 4mmG.I. adjustable rods with

galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to centre long main ‘T’ bottom

exposed with 24mm of all T-sections shall be prepainted with polyester baked paint, for all heights, as per

specifications, drawings and as directed by engineer-in-charge.Note:- Only calciumsilicate false ceiling area

will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs)

having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. Value of 0.50 (Minimum) for

Fine fissured/Spintone/Cosmos and 0.75 NRC for Globe, light reflection 85% noncombustible as per B.S.

part IV, 100% humidity resistance and also having thermal conductivity. 0.043° w/m KC.for the best thermal

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and fixing 12 mm thick grooved macro accoustic wall panelling of Ecotone or equivalent

with solution SR998 or silicone as required and approved as per manufacturer's specifications.

The accoustic board shall have high NRC value, Class A Fire rating, Fire Hazard classification of I or Rupees Three Thousand Eight

97 A in accordance with ASTM E-84 or UL - 723 testing parameters and shall be of colour as Sqmt 46.00 3832.95 Hundred Thirty Two and Ninety

approved by the architect. The rate shall be inclusive of all necessary material, labour, tools, Five Paise Only

tackles, accessories, hardware, loading - unloading, freight etc. for a completed item as instructed

by the EIC. a) Thickness 12 mm

Providing and fixing 9 mm thick grooved macro accoustic wall panelling of Ecotone or equivalent

with solution SR998 or silicone as required and approved as per manufacturer's specifications.

The accoustic board shall have high NRC value, Class A Fire rating, Fire Hazard classification of I or Rupees Three Thousand One

98 A in accordance with ASTM E-84 or UL - 723 testing parameters and shall be of colour as Sqmt 46.00 3166.35 Hundred Sixty Six and Thirty

approved by the architect. The rate shall be inclusive of all necessary material, labour, tools, Five Paise Only

tackles, accessories, hardware, loading - unloading, freight etc. for a completed item as instructed

by the EIC. a) Thickness 9 mm

Roller Curtain:

Providing and fixing roller mounted curtains of approved make and shade as directed by the

Architect/EIC. Rate to be inclusive of requisite mechanism and chain sprocket locking Rupees Three Thousand Three

arrangement for the blinds per one blind. The rate shall be applicable for all floors and for all Hundred Thirty Three Only

heights. Size of blinds shall not exceed 1.80m along width of the opening.

Providing and Fixing in position bought out/ Loose furniture as sample approved by EIC/Architect

as per below specifications. The work shall be measured and paid in Nos. The rates shall be

inclusive of linsead oil / lacquer finish polishing, plywood, veneer, fabric, MS and all material,

labour, wastages, taxes, transportation, loading, unloading, fixing in position including protecting Rupees Fifty Five Thousand

the same against any dents and skretched etc. at all heights, all floors, all levels complete to the Five Hundred Fifty Only

satisfaction of the Architect and EIC.

TWO SEATER SOFA : WIPRO MAKE ALISIYA : AL12 OF BEIGE COLOUR OR EQUIVALENT

Providing and Fixing in position bought out/ Loose furniture as sample approved by EIC/Architect

as per below specifications. The work shall be measured and paid in Nos. The rates shall be

inclusive of linsead oil / lacquer finish polishing, plywood, veneer, fabric, MS and all material,

labour, wastages, taxes, transportation, loading, unloading, fixing in position including protecting Rupees Sixty Six Thousand Six

the same against any dents and skretched etc. at all heights, all floors, all levels complete to the Hundred Sixty Only

satisfaction of the Architect and EIC.

THREE SEATER SOFA : WIPRO MAKE ALISIYA : AL12 OF BEIGE COLOUR OR EQUIVALENT

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Full Height Storage:

Providing, making, polishing and fixing full-height storage of size 450 mm depth as per reference

Material of Construction:

1) Top: 19 mm thick BWR ply finished with 1 mm thick laminate sheet of approved shade, finish

and make. Ply shall confirm to IS

2) Storage Base: The table legs shall be made by 19 mm thick BWR ply confirming to IS 303 to be

finished with 1 mm thick laminate of approved make, shade and texture as per reference drawing.

3) Sides: The sides shall be made by 19 mm thick BWR ply confirming to IS 303 to be finished with

1 mm thick laminate of approved make, shade and texture as per reference drawing.

4) Partitions: Horizontal and vertical partition shall be made of 19 mm thick BWR ply and shall be

finished with 0.8 mm thick laminate of approved make, shade and finish.

5) Lipping: 6 mm thick lipping of ghana teak wood shall be applied on all exposed edges of veneer

and ply as per reference drawing.

6) Polish: Monocoat polish shall be done on all exposed faces of wood and veneer. Rupees Eighteen Thousand

102 8) 0.8 mm thick balancing laminate of approved make, shade and finish to be applied on all inner Sqmt 87.00 18465.83 Four Hundred Sixty Five and

faces of top, bottom, sides, shutters, drawers, shelves and partitions as per the instruction of Eighty Three Paise Only

9) Hardware: Hinges: L Hinges of size 75 mm x 18 mm shall be used in requisite quantity as

approved by the engineer-in-charge; Magnet Lock: 2 Nos. per active shutter; Shutter stop chain:

no. per shutter; Handles: G - profile handles of approved.

The work shall be done as per the approved shop drawing (to be prepared by contractor),

specifications, sample approved and as directed by the Architect and Engineer-in-charge. The rate

shall be for complete item inclusive of all material, labour, wastages, necessary tools &

tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of

approved make (if applicable) for all floors, all heights, all levels and all places within campus.

Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims

will be entertained for this. The unit shall be manufactured in parts and these parts shall be

assembled at site.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Modular Tables: (Non-sharing partition)

Providing and fixing modular table with under storgae of size 1500 mm x 600 mm x 760 mm as

per reference drawing provided by the architect.

Material of Construction:

1) Table Top: 25 mm thick laminated finish of approved make shade and texture table top with

post foam method.

2) The table peripheral aluminum frame shall be of 65 mm thick finished with powder coating of

50-55 micron. Rupees Eighteen Thousand

103 3) Under table unit shall be comprising of 1 drawer unit The drawer shall be provided with Nos 4.00 18091.12 Ninety One and Twelve Paise

telescopic channels. Only

The work shall be done as per the approved shop drawing (to be prepared by contractor),

specifications, sample approved and as directed by the Architect and Engineer-in-charge. The rate

shall be for complete item inclusive of all material, labour, wastages, necessary tools &

tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of

approved make (if applicable) for all floors, all heights, all levels and all places within campus.

Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims

will be entertained for this.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing, making, polishing and fixing table of size 1500 x 600/750 x 750 mm as per reference

Material of Construction:

1) Table Top: 25 mm thick laminated table top comprising of solid box prepared by 19 mm thick

BWR ply. The top shall be finished with 1 mm thick laminate sheet of approved shade, finish and

make. Ply shall confirm to IS 303. The table top sides of 25 mm thickness shall be finished with

mm thick teak wood beading.

2) Table Legs: The table legs shall be made by 25 mm thick BWR ply confirming to IS 303 to be

finished with 1 mm thick laminate of approved make, shade and texture as per reference drawing.

3) Modesty Panel at Front: 19 mm thick BWR ply confirming to IS 303 shall be fixed along the

length of table and finished with 1 mm thick laminate of approved make, shade and texture as

per reference drawing inclusive of keepings grooves and pattern as per the drawing.

4) Lipping: 6 mm thick lipping of ghana teak wood shall be applied on all exposed edges of veneer

Rupees Twenty Eight Thousand

and ply as per reference drawing.

104 Nos 15.00 28443.62 Four Hundred Forty Three and

5) Polish: Monocoat polish shall be done on all exposed faces of wood and veneer.

Sixty Two Paise Only

6) 0.8 mm thick balancing laminate of approved make, shade and finish to be applied on all inner

faces of top, bottom, sides, shutters, drawers, shelves and partitions as per the instruction of

7) Table under storage size 700 x 450 x 500, ( 2 drower & 1 shutter/ 3 drower) as per instruction

The work shall be done as per the approved shop drawing (to be prepared by contractor),

specifications, sample approved and as directed by the Architect and Engineer-in-charge. The rate

shall be for complete item inclusive of all material, labour, wastages, necessary tools &

tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of

approved make (if applicable) for all floors, all heights, all levels and all places within campus.

Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims

will be entertained for this. The unit shall be manufactured in parts and these parts shall be

assembled at site.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing, making, polishing and fixing table of size 1800 x 750 x 750 mm as per reference

Material of Construction:

1) Table Top: 25 mm thick laminated table top comprising of solid box prepared by 19 mm thick

BWR ply. The top shall be finished with 1 mm thick laminate sheet of approved shade, finish and

make. Ply shall confirm to IS 303. The table top sides of 25 mm thickness shall be finished with

mm thick teak wood beading.

2) Table Legs: The table legs shall be made by 25 mm thick BWR ply confirming to IS 303 to be

finished with 1 mm thick laminate of approved make, shade and texture as per reference drawing.

3) Modesty Panel at Front: 19 mm thick BWR ply confirming to IS 303 shall be fixed along the

length of table and finished with 1 mm thick laminate of approved make, shade and texture as

per reference drawing inclusive of keepings grooves and pattern as per the drawing.

4) Lipping: 6 mm thick lipping of ghana teak wood shall be applied on all exposed edges of veneer

and ply as per reference drawing. Rupees Thirty Seven Thousand

105 5) Polish: Monocoat polish shall be done on all exposed faces of wood and veneer. Nos 1.00 37748.75 Seven Hundred Forty Eight and

6) 0.8 mm thick balancing laminate of approved make, shade and finish to be applied on all inner Seventy Five Paise Only

faces of top, bottom, sides, shutters, drawers, shelves and partitions as per the instruction of

7) Table under storage size 700 x 450 x 500, ( 2 drower & 1 shutter/ 3 drower) as per instruction

The work shall be done as per the approved shop drawing (to be prepared by contractor),

specifications, sample approved and as directed by the Architect and Engineer-in-charge. The rate

shall be for complete item inclusive of all material, labour, wastages, necessary tools &

tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of

approved make (if applicable) for all floors, all heights, all levels and all places within campus.

Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims

will be entertained for this. The unit shall be manufactured in parts and these parts shall be

assembled at site.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Side Table with Storage: Providing, making, polishing and fixing Side Table of size 1200 mm x

mm x 690 mm as per reference drawing. Material of Construction: 1) Base: Side table base shall

be prepared by making 19mm thick ply as per reference drawing. 2) Table Top: 38 mm thick

laminated table top comprising of 19 mm thick BWR ply + 19 mm thick BWR ply + 1 mm thick

laminate sheet of approved shade, finish and make. Ply shall confirm to IS 303. The table top sides

of 38 mm thick shall be finished with 1 mm thick laminate of approved make, shade and finish. 3)

Table Bottom, sides & Back: The members shall be made from 19 mm thick BWR ply. 4) Rupees Twenty Three

Drawer: Drawer Bottom shall be made from 6 mm thick ply, and drawer sides, back & front panel Thousand Three Hundred

shall be made from 19 mm thick ply. The front panel shall be provided with profile handles. Each Sixteen and Eighty Six Paise

Drawer shall be provided with telescopic channels of size 400 mm of approved make. 5) Only

Laminate: 1 mm thick laminate of approved make, shade, texture and finish shall be applied as

per reference drawing. 0.8 mm thick balancing laminate of approved make, shade and finish shall

be applied on all inner faces as of table tops, bottoms, sides, drawers, partitions and shelves etc.

6) Lipping: 6 mm thick lipping of ghana teak wood shall be applied on all exposed edges of

wood, veneer and ply, all wood surfec finish monocot polish as per reference drawing.

Side Table with Storage: Providing, making, polishing and fixing Side Table of size 900 mm x 450 mm x

mm as per reference drawing. Material of Construction: 1) Base: Side table base shall be prepared by

making 19mm thick ply as per reference drawing. 2) Table Top: 38 mm thick laminated table top

comprising of 19 mm thick BWR ply + 19 mm thick BWR ply + 1 mm thick laminate sheet of approved shade,

finish and make. Ply shall confirm to IS 303. The table top sides of 38 mm thick shall be finished with 1 mm

thick laminate of approved make, shade and finish. 3) Table Bottom, sides & Back: The members shall be

made from 19 mm thick BWR ply. 4) Drawer: Drawer Bottom shall be made from 6 mm thick ply, and

drawer sides, back & front panel shall be made from 19 mm thick ply. The front panel shall be provided with Rupees Twenty Thousand Five

107 profile handles. Each Drawer shall be provided with telescopic channels of size 400 mm of approved make. Nos 16.00 20529.26 Hundred Twenty Nine and

5) Laminate: 1 mm thick laminate of approved make, shade, texture and finish shall be applied as per Twenty Six Paise Only

reference drawing. 0.8 mm thick balancing laminate of approved make, shade and finish shall be applied on

all inner faces as of table tops, bottoms, sides, drawers, partitions and shelves etc. 6) Lipping: 6 mm thick

lipping of ghana teak wood shall be applied on all exposed edges of wood, veneer and ply, all wood surfec

finish monocot polish as per reference drawing.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Low Height Storage:

Providing, making, polishing and fixing low-height storage of size 450 mm depth & up to 750 mm height as

per reference drawing.

Material of Construction:

1) Storage Top: 38 mm thick laminated table top comprising of hollow box prepared by 19 mm thick BWR

ply. The top shall be finished with 1 mm thick laminate sheet of approved shade, finish and make. Ply shall

confirm to IS 303. The table top sides of 38 mm thickness shall be finished with 0.8 mm thick teak wood

2) Storage Base: The base shall be made by 19 mm thick BWR ply confirming to IS 303 to be finished with

mm thick laminate of approved make, shade and texture as per reference drawing.

3) Sides: The sides shall be made by 19 mm thick BWR ply confirming to IS 303 to be finished with 1 mm thick Rupees Twenty Three

laminate of approved make, shade and texture as per reference drawing. Thousand Four Hundred

108 4) Partitions: Horizontal and vertical partition shall be made of 19 mm thick BWR ply and shall be finished Sqmt 3.00 23474.42

Seventy Four and Forty Two

with 0.8 mm thick laminate of approved make, shade and finish.

5) Lipping: 6 mm thick lipping of ghana teak wood shall be applied on all exposed edges of veneer and ply as

per reference drawing.

6) Polish: Monocoat polish shall be done on all exposed faces of wood and veneer.

8) 0.8 mm thick balancing laminate of approved make, shade and finish to be applied on all inner faces of

top, bottom, sides, shutters, drawers, shelves and partitions as per the instruction of Architect.

9) Hardware: Hinges: L Hinges of size 75 mm x 18 mm shall be used in requisite quantity as approved by the

engineer-in-charge; Magnet Lock: 2 Nos. per active shutter; Shutter stop chain: 1 no. per shutter; Handles: G -

profile handles of approved sample; Telescopic channel: 2 per drawer

The work shall be done as per the approved shop drawing (to be prepared by contractor), specifications,

sample approved and as directed by the Architect and Engineer-in-charge. The rate shall be for complete

item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares

& required SS 304 grade hardware/accessories of approved make (if applicable) for all floors, all heights, all

levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design

intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these

parts shall be assembled at site.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Conference Table:

Providing, making, polishing and fixing conference table of size 600 mm x 760 mm (BxH) as per

reference drawing.

Material of Construction:

1) Table Top: 50 mm thick Veneer / 6mm thick Corian / Artificial Stone table top comprising of

hollow box prepared by 19 mm thick BWR ply. The top shall be finished with 1 mm thick laminate

sheet of approved shade, finish and make. Ply shall confirm to IS 303. The table top sides of

mm thickness shall be finished with 0.8 mm thick teak wood beading.

2) Table Legs: The table legs shall be made by 19 mm thick BWR ply confirming to IS 303 to be

finished with 1 mm thick laminate of approved make, shade and texture as per reference drawing.

3) Modesty Panel at Front: 19 mm thick BWR ply confirming to IS 303 shall be fixed along the

length of table and finished with 1 mm thick laminate of approved make, shade and texture as

per reference drawing inclusive of keepings grooves and pattern as per the drawing.

4) Lipping: 6 mm thick lipping of ghana teak wood shall be applied on all exposed edges of veneer

and ply as per reference drawing. Rupees Fifty Thousand Fifteen

5) Polish: Monocoat polish shall be done on all exposed faces of wood and veneer. and Thirty Nine Paise Only

7) 0.8 mm thick balancing laminate of approved make, shade and finish to be applied on all inner

faces of top, bottom, sides, shutters, drawers, shelves and partitions as per the instruction of

The work shall be done as per the approved shop drawing (to be prepared by contractor),

specifications, sample approved and as directed by the Architect and Engineer-in-charge. The rate

shall be for complete item inclusive of all material, labour, wastages, necessary tools &

tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of

approved make (if applicable) for all floors, all heights, all levels and all places within campus.

Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims

will be entertained for this. The unit shall be manufactured in parts and these parts shall be

assembled at site.

Providing and Fixing in position bought out/ Loose furniture as sample approved by EIC/Architect

as per below specifications. The work shall be measured and paid in Nos. The rates shall be

inclusive of linsead oil / lacquer finish polishing, plywood, veneer, fabric, MS and all material,

labour, wastages, taxes, transportation, loading, unloading, fixing in position including protecting

the same against any dents and skretched etc. at all heights, all floors, all levels complete to the Rupees Thirty Six Thousand Six

110 satisfaction of the Architect and EIC. Nos 2.00 36663.00

Hundred Sixty Three Only

Chair : Merryfair Fulkrum Synchro Tilt Chairs with Executive High Back, Hammock Headrest, 4-

Way adjustable armrest, Synchronized Tilt mechanism, Aluminum backbone in silver expoxy

powder coating & Aluminum base in polished finish or equivalent

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and Fixing in position bought out/ Loose furniture as sample approved by EIC/Architect

as per below specifications. The work shall be measured and paid in Nos. The rates shall be

inclusive of linsead oil / lacquer finish polishing, plywood, veneer, fabric, MS and all material,

labour, wastages, taxes, transportation, loading, unloading, fixing in position including protecting Rupees Seventeen Thousand

111 the same against any dents and skretched etc. at all heights, all floors, all levels complete to the Nos 29.00 17776.00 Seven Hundred Seventy Six

satisfaction of the Architect and EIC. Only

Chair - 5: Merryfair Fulkrum Synchro Tilt Chairs with Low Back, 4-Way adjustable armrest,

Synchronized Tilt mechanism, Aluminum backbone in silver expoxy powder coating & 350 Stiletto

base or equivalent

Providing and placing of fix Chair With Extra Support Of Pips Must Be required For Long Time

Usage Chair Overall Size (approx): H-83 x W-52 x D- 60 (cm) Material Description: Seat & Back:

Seat & back from hot mould plywood of minimum 12 mm thickness of ergonomic design to avoid

back pain. Cushioning: PU foam having density of 40 kg for back and 50kgs/m3 for seat. Average

thickness of foam not less than 50 mm + 10 mm Polly foam. Tapestry: Minimum average weight

required 400to490 gms per sq. mtr,with average weight of 450 grams per square meter

● Frame structure: 4 legs type Frame and handle for arm rest from ERW prime quality tube of

swg, reinforced at all bends for static and impact load with cushioning effect

Rupees Five Thousand Five

112 ● Finishing: All steel parts will be epoxy polyester powder coated to the thickness not less than 50 Nos 10.00 5555.00

Hundred Fifty Five Only

microns finish after 10 tank anti-rust treatment and B grade phosphating (in house) & same will

be demonstrated to the Engineer incharge during pre-dispatch Inspection.

● Product Shoud be Tested by approved BIFMA standard laboratories confirming to ANSI/BIFMA X

5.1- 2002 Cl. No. 5,7,8,12,13,17 on functional requirement. Certificets Should be submiting With

Supply ,Without certificets Product Will Not Be Accepted.All work must be done As per Architect

Drawing & Instructed By Site Engineer

Compactor storage : Double face mobile unit Providing and fixing of Compactor unit Kompress or

equivalent make as per approved sample. Size : @2700 mm x 630 mm x 2535 mm Ht Shelves &

Compartments as per drawing Capacity 60Kgs. UDL /Compartment. Each Mobile Unit will have

Mechanical arrangement Each Component of the System will be treated with rust preventve

treatment and will be powder coated as per approved sample. Rate shall inclusive of mock up Rupees One Hundred Eleven

sample, all materials, loading, unloading, transportation, placing at all floors and for all leads, all Thousand One Hundred Only

accessories as described in item description. Work complete as per the detailed drawing , mockup

sample and instruction of Architect/Client.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Compactor storage : Single face unit Providing and fixing of Compactor unit Kompress or

equivalent make as per approved sample. Size : 2700 mm x 340 mm x 2535 mm Ht Shelves &

Compartments as per drawing Capacity 60Kgs. UDL /Compartment. Each Mobile Unit will have

Mechanical arrangement Each Component of the System will be treated with rust preventve Rupees Seventy Five Thousand

114 treatment and will be powder coated as per approved sample. Rate shall inclusive of mock up Nos 2.00 75750.00

Seven Hundred Fifty Only

sample, all materials, loading, unloading, transportation, placing at all floors and for all leads, all

accessories as described in item description. Work complete as per the detailed drawing , mockup

sample and instruction of Architect/Client.

Compactor : Floor rail Providing and fixing of Floor rail equivalent make as per approved sample.

Optimiser Drive type-Sew Track (Code: TR) (Floor Rail) Rate shall inclusive of mock up sample, all

materials, loading, unloading, transportation, placing at all floors and for all leads, all accessories Rupees Nine Hundred Nine

as described in item description. Work complete as per the detailed drawing , mockup sample Only

and instruction of Architect/Client.

Supply and fixing of welspun make Loope Pile Carpet of Pile Fiber: 100% Bcf Polypropliene Yarn

Construction & Type: Solution Dyed Bulk Continuous Filament Machin Gauge & Stich Rate:

2.54mm (1/10”) 39.4 Rows/100mm, 48/10 Cms. Construction: Loop Pile High Low Scroll Graphic.

Density Factor: 189,600 Tufts/Sq.Mts Tufted Pile Weight & Hight: 850 Gm/Sq.Mt, 6mm (5 %+/-)

Backing: Primary: Woven Polyproplene, Secondery: Action Back Moth Proffing: Naturally Resistat

Bond Strength: 30 Newton Tuff Withdrawal Strength: 20 Newton Flammability: (Astm D 2859-96 Rupees One Thousand Two

& Cpsc-Ff-170) 8 Passes Static Generation: Under 3 Kv Light Fastness: 5+ Usage Area : Commercial Hundred Twelve Only

Heavy Duty Like Auditiriom Office 7 Heavy Traffic Area with backing of 8mm thick armour fixing

on the floor with using favicol SR 505 solution and fixing the carpet above armour including all

accessories, material & labor complete as directed by Architect / Engineer – in – charge.

Providing and placing SS round perforated Dust Bins in approx. 250mm dia and 375mm ht. As per Rupees Nine Hundred Fifty

117 approved sample. Nos. 20.00 959.50

Nine and Fifty Paise Only

Supply of full SS Body waiting chair with four fixed leg covered with PVC caps, 3 seater capacity Rupees Eighteen Thousand

118 with armrest at both ends and as directed by engineer in charge Nos. 15.00 18180.00

One Hundred Eighty Only

Electrification Work

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity

of following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered Rupees Four Hundred Eighty

119 with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe Pt. 92.00 485.81

Five and Eighty One Paise Only

erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (f) with medium

class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat. III

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & earth wire of

sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires,

in below type of pipe to be erected complete with earth continuity and necessary connection

with primary light with accessories erected on Metal / PVC / wooden box covered with 3 mm

thick PC(Polycarbonate) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder Rupees One Hundred Sixty

/ ceiling rose / H.D.Connector as directed. Note:- Maximum up to 6 mtrs length, excess will be Seven and Sixty Six Paise Only

considered as Mains for Secondary Point. (f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked

1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of

pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following type erected on PVC /

Rupees Six Hundred Seventy

121 Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front Pt. 19.00 674.68

Four and Sixty Eight Paise Only

plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked

KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box

122 covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected

with following type of accessories.

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Rupees Five Hundred Ten and

Five Paise Only

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Rupees Seven Hundred Forty

Cat. III Five and Thirty Eight Paise Only

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green) earthing

Rupees Eight Hundred Seventy

125 wire from mcb d b board. Cat. III Pt. 11.00 871.63

One and Sixty Three Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on

PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white Rupees Two Hundred Fifty

126 front plate modules erected on / in wall / ceiling with following type accessories Cat. III Pt. 6.00 257.55

Seven and Fifty Five Paise Only

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(green) both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected

in below type of pipe with 6A Modular type switches and following type of accessories erected on

PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white Rupees Six Hundred Three and

127 front plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle Pt. 2.00 603.98

Ninety Eight Paise Only

holder or ceiling rose or H.D.Connector as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete CAT. III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected

128 with necessary connections as per site situation directed by Engineer In charge.

(2) One No 5 pin plug Cat.III Rupees One Hundred Fifty One

and Fifty Paise Only

(3) Two Pin/RJ-11 [A] For One Gang Telephone Socket Cat.III Rupees One Hundred Sixty and

Fifty Nine Paise Only

(4) TV Co-axial Socket outlet Cat.III Rupees One Hundred Sixty and

Fifty Nine Paise Only

(8) Computer RJ-45 socket Cat.III Rupees One Hundred Sixty and

Fifty Nine Paise Only

(7) Blank Plate Single Cat.III Rupees Twenty Five and

Twenty Five Paise Only

(9) 16 Amp. SP one way switch Cat.III Rupees One Hundred Eighty

and Seventy Nine Paise Only

(10) 6/16Amp. Universal socket Cat.III Rupees One Hundred Ninety

135 Ea. 1.00 199.98 Nine and Ninety Eight Paise

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with Rupees Thirty Three and Thirty

136 adhesive solution & Clamps with following dia of pipes, in approved manner as directed (b) 25 mm Mtr. 1085.00 33.33

Three Paise Only

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

(A) With medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq. mm Rupees Sixty Two and Sixty

(A) With medium class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm Rupees Eighty Two and Eighty

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of Rupees One Hundred Twelve

following size(A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm and Eleven Paise Only

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner

conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Rupees Sixty Two and Sixty

139 Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC Mtr. 50.00 62.62

insulation. (e) RG-11

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer

Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following Rupees Twenty and Twenty

size of conductors & nos.of pairs. With necessary connections. [A] Conductor Size 0.5 mm (a) Paise Only

Unarmoured (2) Two Pairs

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

[C] CAT - 6 Rupees Forty Seven and Forty

Seven Paise Only

SITC of Digital / PCM / TDM EPABX System having SMT design, system with flexible universal

slots. Inbuilt Auto attendant facility, Minimum 15 Nos. conference, Analog extension line, Calling

GSM, E&M line, PRI / EI & VOIP program me through Analog telephone digital key from Ethernet,

public address cord, shall have unrestricted simultaneous dialing facility,

QSIG protocol on PRI, 95 / STD / ISD / Local-Locking, Class of Service, Quick Dial-Single Digit

dialing of any two external number, Once only ring device, Chairman / Secretary - Do not disturb

Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call Back,

Rupees Fifty One Thousand

Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing with Voice Guide System, (DISA),

142 No. 1.00 51440.31 Four Hundred Forty and Thirty

Caller ID (CLI), CLI Base ECF, CLI Base routing Internet Ready Port, External Music Port, Call

Budgeting, Call Most Calculation (ASMDR), DID Direct Inverse Dialing, External Music Input, Fax

Homing, Global Directory Printing with following capacities [[Approved by Competent Authority

i.e. not Below the rank of Executive Engineer ]

[B] No of Extension 24, No of Junctions 9, 8 Port IP Resource in-built, 4 Port Web base Video

Conferencing, No of expandable ports : 96, Operators Console - 01 Compatible : ISDN

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same Rupees Three Thousand Four

143 company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal Ea 4.00 3412.79 Hundred Twelve and Seventy

type outgoing Per phase isolation type (PPI) (b) sheet steel double door (iii)8 way Nine Paise Only

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single

mounting base frame covered with textured/metallic /white front plate,modules erected with Rupees One Thousand One

144 necessary connections as directed Ea 18.00 1133.22 Hundred Thirty Three and

1 no. 6A/16A universal plug-switch combined. Twenty Two Paise Only

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories

Supplying & erecting Electronic Type Cordless Call Bell erected on PVC/Metal board having

Rupees Two Hundred Fifty and

145 portable bell push working on D.C. & bell on 230V A.C. supply with cells / battery Ea 5.00 250.48

Forty Eight Paise Only

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having

10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity Cat.III Rupees Three Hundred Thirty

and Twenty Seven Paise Only

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing box having following capacity

(a) 6 to 32 Amp. Cat.III Rupees Five Hundred Ninety

Five and Ninety Paise Only

(b)40 Amp. Cat.III

Rupees Six Hundred Sixty Eight

and Sixty Two Paise Only

(c)63 Amp. Cat.III

Rupees Seven Hundred Thirty

Seven and Thirty Paise Only

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected as directed

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

(i) 25 Amps.DP Cat. III Rupees One Thousand Nine

148 Ea 12.00 1969.50 Hundred Sixty Nine and Fifty

(ii) 40Amps. DP Cat. III Rupees Two Thousand Two

148.2 Ea 0.00 2235.13 Hundred Thirty Five and

Thirteen Paise Only

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor

type cubical panel board necessary IP-42 and above protection as per approval from engineer

incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection of supplied switch gears,

BUSBARS, suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts, Rupees Sixteen Thousand

149 foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking Sq.Mtr. 1.50 16392.30 Three Hundred Ninety Two and

arrangement and rubber gasket,heavy duty end terminal connection,danger notice Thirty Paise Only

board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy

powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following approved manufacturers with following size.

(C) The standard companies switch gear shall be used and only manufacturers as per IEC

for beneficial use. (i) with 350mm depth

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with

four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current /

cross section area) duly wrapped with colour insulating tape for phase sequence of following Rupees Six Hundred Sixty and

150 current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket Rn.Mtr. 1.50 660.54

Fifty Four Paise Only

to each busbar,erected in existing cubical panel with necessary connections. (A) Suitable for

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. Rupees Six Hundred Sixty Eight

and Sixty Two Paise Only

Rupees Seven Hundred Thirty

Seven and Thirty Paise Only

providing and erecting Approved make Four pole moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed Rupees Six Thousand One

153 thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all internal connections & Nos. 1.00 6173.12 Hundred Seventy Three and

complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III Twelve Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

providing and erecting following additional parts for panel mounting MCCBs (A)Extended

Rupees One Thousand Three

operating rotary handle with pad lock with three position trip,off,on suitable for 25A to 250 A

154 Nos 1.00 1310.98 Hundred Ten and Ninety Eight

panel mounting cat-III

Providing and erecting metallic vitrified danger notice board as per language suggeted by Enginer Rupees Sixty Nine and Sixty

155 in charge for MEDIUM VOLTAGE installation to be erected as per IS.-2551 No. 1.00 69.69

Nine Paise Only

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover, Rupees Forty Three and Forty

156 complete erected with necessary connections. No. 1.00 43.43

Three Paise Only

Supplying and erecting approved make Panel mounting type Digital voltmeter having 3 digits LED

display,external CT operated,for o to 1000 Amp Suitable to operate on 500 V AC erected on Rupees One Thousand Two

157 existing panel board wth all connection, wiring etc.with manufacturers calibrationn certificate.. No. 1.00 1275.63 Hundred Seventy Five and Sixty

Three Paise Only

Supplying and erecting approved make Panel mounting type Digital Ammeter having 3 digits LED

Rupees One Thousand Five

display,0 to 750 AC volts range erected on existing panel board wth all connection, wiring

158 No 1.00 1558.43 Hundred Fifty Eight and Forty

etc.with manufacturers calibrationn certificate..

Three Paise Only

Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC Supply 500 V on Rupees Three Hundred

159 existing panel board with necessary connections. No 1.00 317.14 Seventeen and Fourteen Paise

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA

Rupees Two Hundred Seventy

burden erected in existing CRCA box duly secured with insulating materials connected to the

160 No 1.00 274.72 Four and Seventy Two Paise

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia

of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive compound with high charge dissipation suitable for

following type of applications with chamber and heavy duty cover. (A)(approved make OEM has

to submit test certificate including value of earth resistance of installation duly stamped and

signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in Rupees Five Thousand Seven

161 test Certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Ea. 2.00 5760.03 Hundred Sixty and Three Paise

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & Only

dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test report must be submitted by Agency.

(b)For Electrical installation up to 11 KV in normal soil.

Length of Pipe : 2.00 mtrs

Back filling Compound :1 no. Bag of 25 Kg.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. Rupees Six Hundred Forty

Cat.III Seven and Forty One Paise Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor

for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size Rupees Two Hundred Eighty

of cables (C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) Four and Eighty Two Paise Only

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of Rupees One Hundred Twenty

following size of cables (B) 4 core 6 Sq. mm Six and Twenty Five Paise Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for

1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or Rupees One Hundred Forty and

floor of following size of cables.(C) 4 core 10 Sq. mm Thirty Nine Paise Only

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star rated, Ceiling fan

with Brush Less Direct Current (BLDC) permanent ferrite magnet Motor, class of insulation: B,

Rust free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum

215 CMM, 350 RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with remote unit for Speed Rupees Two Thousand Eight

166 Control and all remaining accessories including safety pin, nut bolts, washers, temperature rise = Ea 27.00 2885.57 Hundred Eighty Five and Fifty

75 degree C (Max.), suitable for 140 to 285 Voltage and rectifier circuit with surge, over current Seven Paise Only

and overload protection , 50 Hz, Single phase AC Supply, earthing etc. Complete as required.[

Make shall be approved by Engineer in Charge] (B) 1200 mm Sweep (48")

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty

ring mounted low noise operation suitable for medium duty having following dia size and

Rupees Two Thousand Fifty

167 maximum speed in RPM [A] 305 mm dia 900 RPM Ea 4.00 2054.34

Four and Thirty Four Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly

painted for fan complete with proper insulation without leckage and earthing. Rupees One Hundred Eight and

Seven Paise Only

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to

50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete Rupees One Hundred Eight and

erected concealed in Ceiling with necessary finishing. Seven Paise Only

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. Rupees Eighteen and Eighteen

Providing suitable M.S. louver shutter of the Exhaust fan.

Rupees Three Hundred Sixty

Eight and Sixty Five Paise Only

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/ aluminium die cast powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

Rupees Three Hundred Seventy

172 LED driver efficiency > 85 % Ea 5.00 373.70

Three and Seventy Paise Only

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between

the ranges shown.

(A) Tube Light with integral driver

(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet Cat-lll

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between

the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

(iv) 22-24 watts, Surge-2 KV Cat-lll

Rupees Seven Hundred Fifty

Eight and Fifty One Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

(ii) 11-15 watts, Surge-2 KV Cat-lll Rupees Four Hundred Twenty

175 Ea 18.00 427.23 Seven and Twenty Three Paise

(i) 5-9 watts,Surge-2 KV Cat-lll

Rupees Two Hundred Twenty

and Eighteen Paise Only

(B) LED Panel Light with provision for Plane front frame with translucent cover fixed to housing Rupees One Thousand Seven

177 complete.IP20 Ea 10.00 1794.77 Hundred Ninety Four and

(vii) from 45 to 48 watts, 24" x 24", Surge-2 KV Cat-lll Seventy Seven Paise Only

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage

of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED Rupees Four Thousand Eight

178 driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below description Ea 25.00 4819.72 Hundred Nineteen and Seventy

have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any Two Paise Only

wattage capacity between the ranges shown.) (C) Post Top Lantern LED fitting comprises of finish

cast aluminum spigot and spun aluminum canopy fixed with opal polycarbonate, pipe

arrangement for vertical mounting driver and accessories wired upto terminal block.IP 65 (ii)32-

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor

type cubical panel board necessary IP-42 and above protection as per approval from engineer

incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection of supplied switch gears,

BUSBARS, suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts, Rupees Sixteen Thousand

179 foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking Sq.Mtr 3.00 16392.30 Three Hundred Ninety Two and

arrangement and rubber gasket,heavy duty end terminal connection,danger notice Thirty Paise Only

board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy

powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following approved manufacturers with following size.

(C) The standard companies switch gear shall be used and only manufacturers as per IEC

for beneficial use. (i) with 350mm depth

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing & Erecting full SS Body (SS 304) Split type water cooler having storage capacity 160 to

175 Ltr.(Tank SS 304) & Cooling capacity 150 ltr. Per hour @ an ambient temp of 350 C.The outlet

temp. of the water should drop by 150C within a hour,The water cooler should be comprising of

hermetically sealed Reciprocating compressor with R134A, fan motor, Copper Condensing unit Rupees Sixty One Thousand

180 with company fabricated Outdoor Unit water tank surrounded by evaporating coil, thermostats, Ea 2.00 61115.10 One Hundred Fifteen and Ten

relay etc.complete with necessary copper tube & Insulation, M.S Chanel Stand with Painting for Paise Only

water tank & M.S. Powder Coated Stand for Outdoor unit with Installation.

With DPELCB and 4 Way DB Box with accessory Three core Cord for connection.

Supplying & erecting reverse osmosis (RO) water purification system with M.S. powder coated

pedestal frame, prefilter housing carbon filter suitable buster DC pump, auto low & high pressure

switches with following size of LPH capacity & erected as directed [E] 200 LPH with 1 phase /

Rupees Ninety Three Thousand

phase Raw water pump of 1000LPH @ 2.5kg/cm2 (1N0 - Kirloskar/CRI/Lubi) , Dual media filter

181 Ea 2.00 93468.43 Four Hundred Sixty Eight and

10"x54" (1 No), Micron catridge filter 20" x 2.5" - (1No), High pressure pump 1000LPH @

Forty Three Paise Only

10kg/cm2 - (1No - Shimge /CRI /Lubi) , RO Membrane housing with RO membrane of 40*40 - (

No),RO pressure tube 4" x 1E-(1No), 0-1200LPH Rotameter-(2 Nos). Recovery Rate 50%.

Providing & erecting open well horizontal mono block pump set with cast iron body, complete for

three phase submersible motor having [C] For 3 HP 3 phase open well horizontal mono block Rupees Fifteen Thousand

182 pump set suitable for 85 LPM to 270 LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia Nos 2.00 15707.52 Seven Hundred Seven and Fifty

delivery pipe Two Paise Only

Supplying and erecting Direct - On - Line Starter with 18 A. rating contactor and with 3.5 Amp.

18A range directly operated in totally insulated elegant enclosure for single phase operation up to Rupees Two Thousand One

183 3 HP as per IS 13947 complete erected on P.W. Block with necessary connection. Cat-lll Nos 2.00 2100.80

Hundred and Eighty Paise Only

Supplying & erecting approved make Automatic liquid level controller 6A. with sensor testing as

Rupees Two Thousand Three

per instruction of Engineer in charge on site complete with wiring connection with existing wires

184 Nos 1.00 2355.32 Hundred Fifty Five and Thirty

with copper conductor from pump to upper and lower tank.

AIR CONDITIONERS

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary

compressor with accessories etc. duly connected separately erected evaporating unit and blower

motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC Rupees Forty Eight Thousand

185 pipes suitable for ( cost includes Eco Friendly green gas charging and 15A plug top & Remote Nos 3.00 48257.80 Two Hundred Fifty Seven and

Control & MS Stand) with necessary core cutting. (1)For ISEER Range (KWH/KWH)(3.1 to 3.99) (B) Eighty Paise Only

for 1.5 ton capacity - Premium Cat.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Supplying and installing MS angle , powder coated / Painted standard type of wall/floor stand

mount for outdoor unit of split AC of following capacity, erected with necessary hardware

Rupees One Thousand Three

materials as directed. (A) 25mm*25mm*3mm thick M.S angle suitable for upto 2 TR. Capacity of

186 Nos. 3.00 1318.05 Hundred Eighteen and Five

Supplying and erecting insulated pair of soft copper tubing open or concealed including power

and control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity Rupees Nine Hundred Sixty

Five and Fifty Six Paise Only

EXTERNAL LIGHTNG

Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole

should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

suitable suspend local wind speed with integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

Rupees Eleven Thousand Four

arrangement for cable termination to be erected With Suitable foundation (Included) as per

188 Nos. 25.00 11411.99 Hundred Eleven and Ninety

details given by manufacturer considering site requirement.(E) 7 Mtr. Long 70 mm Top X 135 mm

Nine Paise Only

bottom dia, 3 mm thickness with 225mmX225mmX16mm base plate, 4-M20 Bolts and 600mm

long with necessary G.I. J Bolts .Approx Pole weight 67 kg

Providing and erecting Street Light pole bracket comprising main B Class MS pipe of

cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx.

45cms.length and suitable for 76.5 mm /80mm / required size of pole top having sufficient

fasteners for fixing the brackets and having spread of 1.5.mtr. length with 110 deg.with vertical Rupees Six Hundred Twenty Six

plane & suitable welded stays, reducer and with check nuts complete painted with one coat of and Twenty Paise Only

Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with following nos of

arms. [A] Single Arm Bracket 1.5 Mtr

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material

at required depth in existing trench for laying of cable. below ground / road surface for Rupees Sixty Two and Sixty

enclosing cable (A)50 mm outer dia Two Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the fault all

Rupees Fifty Five and Fifty Five

191 over the run and back filling the same and making the surface as normal ground. Mtr. 300.00 55.55

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground across the road

crossing or on floor with necessary material in an approved manner and making the ground as Rupees Three Hundred Forty

192 per original. (C) 300 mm dia Mtr. 30.00 343.40

Three and Forty Paise Only

Supplying & erecting IP 55 grade following size section pillar fabricated from joint less M.S. Sheet

with angle iron legs made from jointless M.S. Angle with cable clamps to be buried in ground to

have appropriate erection to work uniform until erected with cement concrete foundation and

cm high bricks work finishing with plaster etc. hinged double door internally supported on both

side, with internal and outside looking arrangement with look and keys in duplicate 35 x 35 x 5 Rupees Sixteen Thousand Six

193 mm M.S. Angle of Two Nos. one is welded and other with nut and bolt for erecting Bakelite sheet. Nos 1.00 16691.26 Hundred Ninety One and

Painting the Section Pillar inside and out side with three tank powder coated paint. section pillar Twenty Six Paise Only

roof should be without joint with water leakage proof & tested as per IP 55 test & followed by IS

2147 of 1962 (A) 150 X 90 X 75 cm section pillar fabricated from 14 Gauge MS Sheet with angle

iron legs 95 cm long made from 40 X 40 X 6 mm thick MS angle.

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on

240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Rupees Three Thousand One

194 Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof No, 1.00 3168.37 Hundred Sixty Eight and Thirty

thermoplastic enclosure & transparent cover erected as required with necessary connection Seven Paise Only

erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per Rupees Two Thousand Seven

195 direction Cat III Nos. 1.00 2782.55 Hundred Eighty Two and Fifty

Five Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Supplying & erecting approved make IP 55 grade Company fabricated Timer Panel of following

capacity for switch On-Off street lights on time scheduling basis made from 16G CRCA sheet duly

epoxy power painted inside and outside with hinged doors and locking arrangement consisting of Rupees Seventeen Thousand

196 suitable size of 4 Pole MCB and 4 pole contactor (cat-III)with analog time switch, auto manual Nos 1.00 17059.91 Fifty Nine and Ninety One

switch of same make and suitable input and output Bakelite terminals and with door earthing Paise Only

approved by Engineer in charge.(C) 63 Amp

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin

Wall Profile, Front Cover : High Transmission Low-Iron Tempered Glass (AR Coated), High

efficency and positive power tolerance Pmax: 0/+5, Module Efficiency should be approx. 19.5%-

22%, Normal operating temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible

and Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules,

Thep. temp. co-efficient of the PV module shall equal or better than -0.45%/degree C. Solar PV

modules of minimum fill factor 75% to be used. Unit Production:- More than 4.5 Unit /kw /day

(Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty includes

all mechanical and electrical parameters of the Solar panel. Modules must be complied to the

DCR(Domestic content requirements). The Ration of AC to DC is 5:6 for the Installation capacity

which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p

Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%,

Operating Tempreture Range: -25~60°C, Integrated protection of Inverter are Anti-islanding

Protection, Input Reverse Polarity Protection, Insulation Resistor Detection, Ground fault

protection, Residual Current Monitoring Unit, Output Over Current Protection, Output Short

Circuit Protection, Output Over Voltage Protection, PV array string fault Protection. Protection

Degree: IP65, User Interface LCD & APP, Datalogger & Communication: GPRS / Wi-Fi.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated,

Residual Current Monitoring Unit Integrated, Output Over Current Protection Integrated, Output

Short Circuit Protection Integrated, Output Over Voltage Protection Integrated, Protection

Degree: IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module

Mounting Structure: The mounting (Rectangular pipe / square pipe / circular pipe) with requisite

cross bars, nuts and bolts, etc. shall be Hot deep galvanized with minimum 80micron coating. The

Rectangular / square /circular hollow pipe section used for the structure should have a minimum

thickness of 2.0 mm. other than above, the material thickness should be minimum 2.5 mm. A

certificate of a structural engineer certifying the strength and stability of the mounting structure

to withstand the weight and wind speed of 150 km/hour throughout the life span of 25 years of

the system, shall be submitted by the vendors. Hot Dipped Galvanized steel coils. suitable

arrangement for base plate for foundation , solar panel mounting, the structure should be

suitable for carry the load of solar panel,wiring, sprinkler system etc. with necessary foundation

work/wall mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be

(SS 304) quality.The ground clearance of the bottom most edge of solar panel shall not be less

than 300 mm to 1200 mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with

necessary Swichgears (Suitabel size and protection of ACDB & DCDB), inter connecting wiring,

earthing system as per the CEIG drawing approval, lightining arrester system as per the CEIG

drawing approval, all liasoning work with various gov. dipartment like state nodal agency,DISCOM

& CEIG is included in agency scope

(Excluding All charges namely GEDA Application fees, Solar connectivity Charges, Meter

connectivity Charges, Meter testing Charges and system stability/strenthning charges.)

(B) Grid Tied Solar Power System: 6 - 10 kW (3 - phase) Rupees Forty Four Thousand

197 Per Kw 10.00 44081.45 Eighty One and Forty Five Paise

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Providing & erecting Automatic solar panel cleaning system for solar power projects which

includes necessary plumbing work (UPVC pipes and accessories) from source of water to project

site (upto 30 meters),Suitable size of sub mercible/ open well motor, necessary wiring for motor Rupees Three Thousand Eight

198 and sprinkler system with safety, timer circuit for automatically on/off the sprinkler system, Per Kw 10.00 3852.14 Hundred Fifty Two and

necessary size oand number of nozzles/JET (minimum 1 Nozzle/Jet per module)(B) Grid Tied Solar Fourteen Paise Only

Power System: 7 - 10 kW (3 - phase)

DC Cable: Electron beam cross linked compound,UV, Ozone, Temperature & Hydrolysis resistant

Flame Retardant, Low Smoke Excellent Encapsulation

Very long / Service life >

Standards / Material Properties:

Fire performance : IEC 60332-1-2

Smoke emission : IEC 61034/ EN 50268-2

Rupees Seventy Six and

199 Halogen Free: EN 50267-2-1/-2, IEC 60754-2 Mtr. 40.00 76.76

Seventy Six Paise Only

Toxicity: EN 50305, ITC – Index <3

Ozone Resistant : EN50396

Weathering UV: HD 605/A1 or DIN

Approvals : EN 50618; H1Z2Z2-k

with suitable sized of PVC pipe(ISI Mark) and Clamps,Shadels,Lugs. (B) 1 core 4 sqmm copper DC

cable Colour Black (B) 1 core 4 sqmm copper DC cable Colour Black

Supplying & erecting D.C.P. type fire extinguisher for following capacity cartridge type with gun

metal cap 150 gram CO2 gas cartridge, powder and brackets confirming to IS 2171 1985 and Rupees One Thousand Seven

200 complete erected with necessary clamps made from 50 x 6 mm M S Flat with nuts and bolts Ea 10.00 1712.96 Hundred Twelve and Ninety Six

grouted in wall complete. [A] For 5 Kg Capacity Paise Only

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with

necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. Rupees Six Thousand Five

201 [A] For 4.5 Kg Capacity Ea 10.00 6591.26 Hundred Ninety One and

Twenty Six Paise Only

Supplying & erecting ABC powder type 'Ceasefire' type Fire extinguisher as per IS 13849 or 1 Kg Rupees One Thousand Five

202 capacity with necessary clamp for erection on wall Ea 10.00 1542.27 Hundred Forty Two and

Twenty Seven Paise Only

Getting GEB/TORRENT CONNECTION Liaising Charges.

Rupees Twenty Five Thousand

Two Hundred Fifty Only

Drilling pilot bore hole of size 250 / 300 mm at above village site in all starata by mud flush direct

Rupees Five Hundred Seventy

204 rotary rig mtr 125.00 573.68

Three and Sixty Eight Paise Only

Reaming of 250 / 300 mm dia pilot bore hole to size 550 mm dia. including assembling, jointing,

lowering of housing casing screen pipes & other assembly items with gravel packing and clay balls Rupees Three Hundred Forty

packing etc Nine and Forty Six Paise Only

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Development of bore by air compressor of 900 cfm / 200 psi capacity for minimum 06 hours or Rupees Twenty Seven

206 up to the availability of sand free discharge job 1.00 27603.30 Thousand Six Hundred Three

and Thirty Paise Only

Manufacture, supply and delivery of 200 mm dia (Min. 6 mm thickness) ISI marked ERW M.S. Rupees Two Thousand Four

207 Pipes confirming to IS:4270/2001 with latest amendment. Rates are exclusive of GST. mtr 80.00 2431.07 Hundred Thirty One and Seven

Manufacture, supply and delivery of cage typeTrapezoidal shape ( ' V ') wire wound low carbon,

Rupees One Thousand Five

Galvanized screen pipe and Stainless Steel Screen pipes, confirming IS: 8110. Low carbon,

208 mtr 40.00 1556.41 Hundred Fifty Six and Forty

Galvanized screen pipe (B) 200 mm dia. REGULAR 2) 1.50mm Slot size

Clamp made from M.S. plate with 3 holes on either side with nuts & bolts of Std. Make and Rupees Two Thousand Thirty

209 suitable size. 900 mm X 100 mm X 16 mm flat suitable for 250 mm dia.Pipe. pair 1.00 2037.91 Seven and Ninety One Paise

Supply of Bore plug having 100 mm height made from M.S. Plate with 3 holes at equal distance

on circumference for nut-bolts type,locking arrangement with nut-bolts & lock nuts of std. Make Rupees One Thousand One

210 complete from 5 thick M.S. Plate(For Tap also) suitable for 250 mm dia pipe No. 1.00 1161.62 Hundred Sixty One and Sixty

Bail plug of length 0.45 meter made from MS medium class pipe as per IS suitable for 200 mm dia. Rupees Eight Hundred Fifty

One and Four Paise Only

Steel bent plates suitable to ERW pipe for 200 mm dia. 150 X 150 X 6 Rupees Sixty Seven and Twenty

Supply of gravels of selected size 4 mm to 6 mm Rupees Two Thousand Forty

213 cum 15.00 2049.29 Nine and Twenty Nine Paise

Supply of clay ball of size ranging from 25 mm to 50 mm made from stickly clay at site of work as

Rupees Seven Hundred Fifty

214 certified by Hydrologist. Cmt 6.00 758.51

Eight and Fifty One Paise Only

Supply of cement. Rupees Six Thousand Three

215 MT 1.00 6365.02 Hundred Sixty Five and Two

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Cement sealing if necessary without cost of cement by means of mud pump. Rupees Thirteen Thousand

216 Job 1.00 13405.73 Four Hundred Five and Seventy

Three Paise Only

Bottom sealing Rupees Six Thousand Seven

217 Job 1.00 6727.61 Hundred Twenty Seven and

Sixty One Paise Only

Electrologging of pilot bore Rupees Eighteen Thousand

One Hundred Eighty Only

Geohydrological ground water investigation charges Rupees Fourteen Thousand

219 Job 1.00 14428.86 Four Hundred Twenty Eight

and Eighty Six Paise Only

Water sample chemical analysis charges.

220 No. 2.00 1010.00 Rupees One Thousand Ten Only

Conducting pumping test of 200 / 250 mm dia. DR tube well by submersible pump of adquate Rupees Twenty Nine Thousand

221 capacity using DG set of required rating including providing all required tools / tackles etc. as Job 1.00 29425.34 Four Hundred Twenty Five and

mentioned below for all districts. 1st 24 hours. (up to 30 HP) Thirty Four Paise Only

Providing and constructing filter chamber of size 2.06 x 1.21 x 1.20 mt. as directed including Rupees Eleven Thousand Seven

222 connection rainwater pipes as per detailed as directed by Engineer in charge including cost of No. 1.00 11759.43 Hundred Fifty Nine and Forty

labour and material. Three Paise Only

Providing water harvesting pit of 2.00 mt x 2.00mt x 3.00 mt. size for water logging with

excavation in any strata upto four meter depth, filling the pit with B.T.Metal 3-60 mm in 1 mt. Rupees Sixty Five Thousand

223 depth in different layers and 2.0 mt. depth with coarse sand in layers including making P.V.C. line No. 1.00 65574.25 Five Hundred Seventy Four and

for water inlet etc. as directed with 250mm dia bore 35 mt. depth and 150mm dia P.V.C. pipe of Twenty Five Paise Only

10 Kg.f/Cm2 casing with gravel packing or as directed.

Sr No. ITEM OF WORK Unit Total Qty Rate in Figure Rate in Words Amount

Demolition and Credit

Credit of Dismentaling material:-Dimolation of RCC Work, Brick Work, Floor Tiles, Window,

Doors, etc.... including stacking of serviceable material as and disposal of unserviceable materials

with all lead and lift. And clean area, credit value for dismantling the existing the items brick bats,

floor tiles, door, window, steel in RCC etc... carting dabris of the same at a appropriate place and

clearing the site dismantled material shall be the property of the contractor and rate to be

quoted for credit of materials receive after counting the expenditure of dismantaling removing Rupees Two Thousand Seven

carting weight of scrape. The rate include the safety measure and stacking the material in spoil Hundred Sixty One Only

bank as and where directed by the engineer in charge. After proper removal of items. the

conctractor give the rebate from total amount quoted the actual servicable mesured and

conctractor give the rebate from total amount quoted the actual servicable mesured and

approved by engineeer in charge.

SAY Total Amount

SAY Total Amount

I / We am / are willing to carry out the work at __________% above / below __________ percentage (should be written in figures and words) of the estimated rates mentioned above. Amount

of my/our tender works out as under.

Estimated Amount put to Estimated Amount put to

Deduct _________ % Below. Add _________ % Above.

1 All work shall be carried out as per Public Works Department Handbook and other specifications of Division or as directed.

2 All columns in the Schedule should be filled in ink and the total of the entire in the last columns should be struck by the contractor under his signature.

3 Rates quoted include clearance of site (prior commencement of work and at its close) in all respects and hold good for work under all conditions, site, moisture, weather etc

4 To be continued on additional sheets, if found necessary.

5 The Labour Cess will be deducted as per prevailing rules i.e.1% of the work done.

6 Credit Value of Dismantle Material Rs.00 (as per Schedule B) will be recovered in 1st RA bill of Contractor.

7 The bituminous work shall be carried out by the contractor or as under by utilizing.

8 For abnormal high or law rates payment of such items shall be regulated as per Govt. Circular letter No. Parach-102008-61-S dated 27-11-2008 attached with tender papers.

9 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no extra payment shall be made.

10 GST and Income tax TDS will be deducted at a source while making payments of bills.

11 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in

Seal & Signature of the Bidder City Engineer

Date- Gandhinagar Municipal Corporation