Construction of New Mamlatdar Office (D-Type) at Umarpada, Tal.Umarpada, Dist.Surat.

Name of Work :- Construction of New Mamlatdar Office (D-Type) at Umarpada, Tal.Umarpada,

BILL OF QUANTITIES

(A) Percentage Rate Tender (Up to INR 50 Cr. )

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

1 Excavation for foundation upto 1.5 m depth including sorting out and 1223.00 Cumt 157.52

stacking of useful materials and disposing off the excavated stuff upto

Meter lead. (B) Dense or Hard soil.

2 Excavation for foundation for depth from 1.5 m to 3.0 m including sorting 612.00 Cumt 170.87

out and stacking of useful materials and disposing off the excavated stuff

upto 50 Meter lead. (B) Dense or Hard soil.

3 Filling in foundation and plinth with sand in layers of 20 cm. Thickness 159.00 Cumt 481.80

including watering ramming and consolidating etc. comp.

4 Filling available excavated Earth (Excluding Rock) in trench plinth side of 790.00 Cumt 136.92

foundation in layer not excluding 20 cm in depth consolidation each

deposited layer by ramming and watering etc. complete.

5 Filling foundation and plinth with murrum or selected soil in layer of 20 cm 420.00 Cumt 301.78

in thickness including ramming watering and consolidating etc. complete.

6 Applying general insecticide pest control treatment to floors, cupboards etc 728.00 Sqmt 91.63

including labour material etc. complete. Using Imidacloprid 30.5 SC. As Per

6113 Part-II (0.075% concentration by mass) is recommended 10.5ml

chemical diluted with 5 liters of water application 0.5 liters chemical / sqm

of surface is recommended as per I.S.

7 Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- 39.00 Cumt 3095.25

machine cut stone aggregates 40 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth.

8 Providing and laying controlled cement concrete M150 for curing complete 330.73 Cumt 4377.34

including cost of formwork but excluding the cost of reinforcement for

reinforced concrete work in PCC.

9 Providing and laying controlled cement concrete M250 and curing complete 275.00 Cumt 4600.15

including the cost of formwork and excluding reinforcement for reinforced

concrete work for Foundations, Footings, Mass concrete for Footing.

10 Providing and laying controlled cement concrete M250 and curing complete 24.00 Cumt 7351.79

including the cost of formwork and excluding reinforcement for reinforced

concrete work for Column Upto GL.

11 Providing and laying controlled cement concrete M250 and curing complete 126.00 Cumt 6223.62

including the cost of formwork and excluding reinforcement for reinforced

concrete work for Plinth Beam / Ground Beam.

12 Providing and laying controlled cement concrete M200 and curing complete 78.50 Cumt 5643.58

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Plinth Slab.

13 Providing and laying controlled cement concrete M200 and curing complete 9.00 Cumt 7385.12

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Column Upto PL.

14 Providing and laying controlled cement concrete M-200 and curing complete 57.00 Cumt 7307.45

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and struts For GF.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

15 Providing and laying controlled cement concrete M-200 and curing complete 38.00 Cumt 7307.45

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and struts For FF.

16 Providing and laying controlled cement concrete M-200 and curing complete 12.00 Cumt 7348.40

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and struts For SF.

17 Providing and laying controlled cement concrete M.200 and curing complete 124.00 Cumt 6189.19

including the cost of formwork and excluding reinforcement for reinforced

concrete work in (C) Ground floor Beams.

18 Providing and laying controlled cement concrete M.200 and curing complete 88.00 Cumt 6189.19

including the cost of formwork and excluding reinforcement for reinforced

concrete work in (C) F floor Beams.

19 Providing and laying controlled cement concrete M-200 and curing etc. 2.00 Cumt 6471.41

complete including the cost of form work and reinforcement for reinforced

concrete work in (c) Chhajja for Ground floor.

20 Providing and laying controlled cement concrete M-200 and curing etc. 4.00 Cumt 6471.41

complete including the cost of form work and reinforcement for reinforced

concrete work in (c) Chhajja for F floor.

21 Providing and laying controlled cement concrete M-200 and curing etc. 5.00 Cumt 7509.10

complete including the cost of form work and reinforcement for reinforced

concrete work in (c) Lintal for Ground floor.

22 Providing and laying controlled cement concrete M-200 and curing etc. 4.00 Cumt 7509.10

complete including the cost of form work and reinforcement for reinforced

concrete work in (c) Lintal for F floor.

23 Providing and laying controlled cement concrete M.200 and curing complete 107.50 Cumt 6963.53

including the cost of formwork and excluding reinforcement for reinforced

concrete work in (C) Ground floor Slab.

24 Providing and laying controlled cement concrete M.200 and curing complete 71.00 Cumt 6963.53

including the cost of formwork and excluding reinforcement for reinforced

concrete work in (C) F floor Slab.

25 Providing and laying controlled cement concrete M-200 and curing etc. 8.00 Cumt 7383.03

complete including the cost of form work and excluding the cost of

reinforcement etc. complete in (E) Stair case for Ground Floor to first floor.

26 Providing and laying controlled cement concrete M-200 and curing etc. 25.00 Cumt 8068.80

complete including the cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and horizontal wall for F.floor.

27 Providing and laying controlled cement concrete M-200 and curing etc. 7.00 Cumt 8109.76

complete including the cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and horizontal wall for S.floor.

28 Providing and laying controlled cement concrete M-200 for RCC work and 8.00 Cumt 6394.07

curing complete including the cost of form work but excluding the cost of

reinforced concrete work in coping on Ground Floor.

29 Providing and laying controlled cement concrete M-200 for RCC work and 3.00 Cumt 6394.07

curing complete including the cost of form work but excluding the cost of

reinforced concrete work in coping on F Floor.

30 Providing and laying controlled cement concrete M-200 for RCC work and 6.00 Cumt 6435.03

curing complete including the cost of form work but excluding the cost of

reinforced concrete work in coping on S Floor.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

31 Providing IS Mark TMT FE-500D bar reinforcement for RCC work 136346.00 Kg 77.33

including bending & placing in position complete up to All floor Level.

32 Providing and fixing 90 cm Height Stainless Steel Railing made from 47.00 Rmt 4332.90

anticorrocive 316 grade S S pipe of 50 mm dia (16 Gauge) as hand rail with

S S 316 grade Baluster of 40 mm dia (16 Gauge) as a vertical support fixed

in RCC slab at 1.2m c/c including three horizontal S S pipes of 25 mm dia

(16 Gauge) at eqal distance fixed by 18.75 mm dia (16 Gauge) S S pipe with

baluster including accessories as per detailed drawing as directed etc.

33 Brick work using common burnt clay building bricks having crushing 121.00 Cumt 4214.33

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional below plinth.

34 Brick work using common burnt clay building bricks having crushing 143.00 Cumt 4503.04

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional For GF.

35 Brick work using common burnt clay building bricks having crushing 105.00 Cumt 4503.04

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional For FF.

36 Brick work using common burnt clay building bricks having crushing 32.00 Cumt 4545.47

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional For SF.

37 Half Brick masonry in common brunt clay building bricks having crushing 258.00 Sqmt 685.66

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -

coarse sand) in foundation and plinth (B) Conventional in super structure.

38 Half Brick masonry in common brunt clay building bricks having crushing 167.00 Sqmt 685.66

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -

coarse sand) in foundation and plinth (B) Conventional in super structure.

39 Providing and fixing 150 mm wide, approved quality chicken wire mesh at 386.00 Sqmt 295.93

junction of brick work and RCC work or two dissimilar surfaces, at all

heights fixed by nails, rowal plugs or tag before applying the plaster,

including curing, scaffolding all complete as directed.

40 Providing 15mm thick cement plaster in single coat on Rough (Similar)side 1756.00 Sqmt 167.26

of single or half brick walls for interior plastering upto floor two level and

finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) For

41 Providing 15mm thick cement plaster in single coat on Rough (Similar)side 1660.00 Sqmt 167.26

of single or half brick walls for interior plastering upto floor two level and

finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) For F

42 Providing 15mm thick cement plaster in single coat on Rough (Similar)side 235.00 Sqmt 191.82

of single or half brick walls for interior plastering upto floor two level and

finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) For S

43 Providing 10 mm Thick cement plaster in single coat for plastering on 675.00 Sqmt 148.32

ceiling and soffits of stairs and finished even and smooth in : (I) Cement

mortar 1:4 (1 cement : 4 sand) smooth finish etc. complete G Floor.

44 Providing 10 mm. Thick cement plaster in single coat for plastering on 446.00 Sqmt 148.32

ceiling and soffits of stairs and finished even and smooth in : (I) Cement

mortar 1:4 (1 cement : 4 sand) smooth finish etc. complete F Floor.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

45 20 mm thick Sand faced cement plaster with 1cmx1cm grooves as suggested 2197.00 Sqmt 337.34

by this office consisting of 12 mm thick backing coat of C.M. 1:3 (1 cement

: 3 coarse sand) and 8 mm thick finishing coat of C.M. 1:1 (1 cement :

coarse sand) for all heights as directed etc. complete. and as per pattern

sample aprroved by the architect or directed engineer in-charge.

46 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 122.00 Rmt 44.28

47 Providing and fixing eco-friendly light weight calcium silicate false ceiling 280.00 Sqmt 1674.15

tiles having Tegular edge & 15 mm Thick Densified edges on the Tile

Periphery for Extra Strength The Light weight calcium silicate ceiling tiles

shall have, light reflection 85% non-combustible as per B.S. 476 part IV,

100% humidity resistance and also having thermal conductivity0.043° w/m

KC.for the best thermal Insulation. The Light weight calcium Silicate tile

shall be of approved texture Fine fissured/ Spintone/ Cosmos having NRC

value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size

595 X 595 mm to be laid on true horizontal level suspended inter locking

metal grid of hot dipped galvanized steel sections (galvanizing @120 grams

per sqm including both side) consisting of main ‘T’ runner suitably spaced

at joints to get required length and size of 24 X 38mm made from 0.30 mm

thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24 X

28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced

between main 'T' at 600mm centre to centre to form agrid of 1200x600mm

and size 24x48mm made of 0.30mm thick (Minimum) sheet to be

interlocked at middle of the 1200x600mm panel to form grid of size

600x600mm resting on periphery walls/partitions on a perimeter wall angle

pre-coated steel of size (24x24x3000mm made of 0.40mm thick (minimum)

sheet with the help of rawl plugs at 450mm centre to centre with 25mm long

dry wall screws @ 230mm interval and laying 15mm thick densified edges

light weight calcium silicate ceiling tiles of approved texture (Fine

fissured/Cosmos/Spintone) in the grid including cutting/making opening for

services like diffusers, grills, light fittings, fixtures, smoke dtectors etc.,

wheneveer required, Main 'T' runners to be suspended from ceiling using

G.I. slotted cleats of size 25x35x1.6mm fixed to ceiling with 12.5mm dia

and 50mm long dash fasterners, 4mm G.I. adjustable rods with galvanized

steel evel clips of size 85x30x0.8mm, spaced at 1200mm center to centre

48 long main 'T'

Applying twobottom

coats exposed with lapy

of Acrylic 24mm of all T-sections

(putty) & two coatsand also provideof

of primer 4698.00 Sqmt 40.59

approved brand and manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from mortar dropping and

other foreign matter and sand papered smooth.

49 Wall painting (two coats) with plastic emulsion paint of approved brand and 3579.00 Sqmt 84.37

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

50 Painting (two coats) with plastic emulsion paint of approved brand and 1119.00 Sqmt 90.05

manufacture on undecorated ceiling surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

51 Wall Painting (Two coats) with weather proof acraylic emulsion paint of 2184.00 Sqmt 120.26

approved brand and manufacture and of required shade on exterior wall

surface to give an even shade over and including primery coat with Alkaly

resistance primer of approved brand after thoroughly brushing surface to

remove all dust and remains of loose powdered material etc. comp. for all

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

52 Providing And filling with good quality cinder (steam coal) as directed by 28.00 Cumt 555.50

engineer in charge in sunks in layers of 15 cm thick,including watering,

placing, ramming well etc. as directed for all floor.

53 Providing and laying broken chine mosaic flooring for terrace using 12 mm 729.00 Sqmt 710.72

to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar creme out upto surface

using white cement including rounding off junctions and extending them

upto 15 cm along the wall,clearing with water and oxalic acid etc. as

54 Providing and laying cement concrete flooring 1:2:4 (1-cement : 2- coarse 729.00 Sqmt 339.08

sand : 4-graded stone aggregate 20mm nominal size) laid in one layer and

finished with a floating coat of neat cement (B) 50mm thick.

55 Providing Plinth Protection to Building including excavation in ordinary soil 156.00 Sqmt 2321.99

and laying cement concrete 1:3:6 using stone aggregates of 40mm nominal

size in foundation layer 125 mm thick+ 125mm thick sand layer below pre-

cast Rubber Dye inter locking concrete block 60mm thick with grade of

concrete M300 pneumatic compressed by mechanically pressed and as per

approved design including 75mm Sand layer for levelling and filling the

joint with sand in proper line and level etc. complete, Including Providing

and fixing pre-cast concrete kerb stone of grey cement based concrete block

30cm length, 30cm height and 15cm thick made of M250 grade concrete as

per approved design and including excavation for fixing in proper line and

level, filling the joint with C:M 1:3 (1cement:3 fine sand) etc. complete.

56 Providing and fixing three track Sliding window + fixed glass at top having 27.00 Sqmt 3407.74

standard extruded colour anodized aluminum section equivalent to jindal

series C (20 mm) section numbers are : shutter top -20530, bottom-

shutter inter lock - 20531, shutter side (handle) - 20544, frame-bottom with

gutter- 21651, frame top & side – 21650 with 5 mm thick transparent tinted

float glass in shutter as well as fix glass top of window with rubber gasket,

air lock strip and finishing joints with silicon sealant with standard extruded

colour anodized aluminum coated fittings as per details etc complete.

57 Providing and fixing fixed window having standard extruded colour 26.00 Sqmt 2709.83

anodized aluminum section equivalent to jindal frame-bottom with gutter-

20128, frame top & side – 20147 with 5 mm thick transparent tinted float

glass in shutter as well as fix glass top of window with rubber gasket, air

lock strip and finishing joints with silicon sealant, with standard extruded

colour anodized aluminum coated fittings as per details etc complete. fixed

58 Providing and fixing CASEMENT window having standard extruded colour 62.00 Sqmt 5149.99

anodized aluminum section equivalent to jindal series B section numbers are

: 20558, 20559, 20560, 19391 with 5 mm thick transparent tinted float glass

in shutter as well as fix glass top of window with rubber gasket, air lock

strip and finishing joints with silicon sealant, with standard extruded colour

anodized aluminum coated fittings as per details etc complete.

59 Providing & Fixing in position standard extruded approved colour anodised 7.00 Sqmt 2722.96

Aluminum Ventilation with outer frame 65 x 25 x 1.50 mm Stander Box

Frame @ Wt 0.833 kg/Rmt with 5mm thick fixed ground glass fixed to

alluminium strip blade fixed or adjestable ventilation & including all

required materials, fixtures, fastenning, labours and equipments as per

detailed drawing as directed. For Ventilators.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

60 Providing and fixing Entrance wooden hollow two flush door shutter with 28.00 Sqmt 6296.34

anodized aluminium section fram inserted non teakwood, shutter made from

teak wood frame 5cm x 15cm and 6 no. 5cm x 5cm horizontal rail and

vertical rail cover with both side water proof ply wood of 6mm thick with

1mm thick lamination on both side including requires teakwood batten of

one coat of primer & two coats of enamel paints on frame & edges, design

of which is to be approved by the architect, also added Door shall be

providing with floor spring Pivoted and 30cm long stainless steel handle and

necessary Locking system of Godrej, fixtures & fastenings etc. directed by

engineer in charge.

61 Providing and fixing 38 mm thick solid core type-I Single Flush door 68.00 Sqmt 6473.09

shuttered having factory made & stamped I.S 12552 grade-I three layered

resin flushed door having decorative lamination on both sides & 12 mm

thick teak wood beading fixed around the door including melamine polished

at edges, fixing by Zinc coated hinges for durable grip including 15cm long

stainless steel handle, Aldrop, stopper and necessary Locking system, S.S.

fixtures & fastenings etc. directed by engineer in charge. The door from

“NOVAPAN” OR Equivalent company holding licence for minimum

62 Providing and fixing FRP frame size 100 x 50 mm and 35 mm thick (Fiber 21.00 Sqmt 2363.40

Glass with PUF Injection) FRP depress panel Single or Double shutter

having extra reinforcement on sides & edges in Gel coat finish.The core of

the both shutter & frame is to be filed up with injected fire retradat grade

polyurethene foam done in situ along with embeded wooden pieces for

stiffening & also taking hinges & fintures.The whole FRP frame & single or

double shutter is to be waterproof, weatherproof, termite proof & resistance

to mild acid / alkali. Rates are to be inclusive of S.S hinges with necessary

screws & S.S fixtures & fastenings & fartener sleeve. Colour and Shade

approved by Engineer-In-Charge.

63 P & L 24" x 24" vitrified 8 mm thick Soluble Salt tile flooring over 20 mm 948.00 Sqmt 1640.24

(average) base of cement mortar 1:6 (1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc. complete

(tack 10% DARK shade).

64 P & L 24" x 24" vitrified 8 mm thick tile skirting over 12 mm (average) base 58.00 Sqmt 1282.70

of cement mortar 1:3 (1 cement: 3 coarse sand) on new surface or fixing on

existing flooring by adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including finised with flush

pointing & cleaning the surface etc. complete (tack 10% DARK shade)

65 Providing and laying Porcelene tiles 60 x 60 cm size 6 mm thick in flooring 32.50 Sqmt 1320.07

treads of steps and landing laid on a bed of 12 mm thick cement mortar 1:3

(1-cement:3-coarse sand) finishing with flush pointing in white cement etc.

66 Providing and laying antiskid ceramic tiles 30 x 30 cm size 6 mm thick in 78.50 Sqmt 1017.30

flooring treads of steps and landing laid on a bed of 12 mm thick cement

mortar 1:3 (1-cement:3-coarse sand) finishing with flush pointing in white

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

67 Providing and laying primium printed glazed tiles tiles size 30 x 60 cm 8 411.00 Sqmt 1513.28

mm thick in skirting risers of steps and dedo on 10 mm thick cement plaster

1:3 (1-cement: 3coarse sand) and jointed with colour cement slurry etc

68 Providing and laying machine cut free edge machine Green Marble Slab 18 38.00 Sqmt 944.35

to 20 mm finished treads and risers in length with 1cm projecting nozing

rounded moulding in ttread laid over 20 mm (av.) thick of CM 1:6 on treads

and 10mm thick CM 1:3 on risers jointed with grey or colour cement slurry

including rubbing and polishing incl. making Three No.s of grooves of size

3mm X 3mm along the length of treads etc. complete.

69 Providing and laying 10 to 12mm thick ready made Full body vitrified 29.00 Sqmt 2601.76

antiskid flutes step tile of 120x30cm Tread, 120x15cm riser & 60x60cm

Landing with 1cm projecting, nosing half rounded moulding in tread , laid

over 12 mm (av.) thick bases of cement.

70 Providing and laying Readymade Full Body Vitrified Tile thick in risers of 5.00 Sqmt 3008.79

steps, skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with gray cement slury mixed with

pigment to match the shade of slab including rubbing and polishing etc.

71 Providing and fixing frosted finished 600mm x 1200mm glass urinal 5.00 Sqmt 6008.49

partition with crystalline Dhar polish on exposed edges, supported by SS

legs and fitting bracket clamp with cut holes and silicon grouting, including

all accessories and labor charges directed by the engineering in charge, etc.

72 Providing and fixing mirror polished 18 mm thick Green Marble stone with 253.00 Sqmt 2279.57

full round edge and polished of approved quality in clading on sill and

around the doors/ windows/ ventilation with 12 mm thick cement mortor

CM (1:4) and fixing with cement slurry & adhesive including moulding of

exposed edges as directed by engineering in charge etc. complete.

73 Providing and fixing M.S Safty Grills having 16mm Solid MS Squre bar 134.00 Sqmt 2065.45

Horizontally at every equal 0.10m C/C distance and 2 no of bar Vertically at

every equal 0.375m C/C distance Fixing on around (5x40) mm Solid MS

Patti including cutting, welding and fabrication etc; including one coat of

primer of approved quality and two coats of oil painting as per detail

drawing etc. complete as per directed Engineer in charge.

74 Providing erecting and fixing double coated PVC. (ISI) water tank of 14000.00 Litre 3.95

required capacity each with all necessary fittings and connection etc.

complete on terrace.

75 Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe 200.00 Rmt 195.67

(SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

76 Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe 80.00 Rmt 148.12

(SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

77 Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe 180.00 Rmt 91.84

(SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

78 Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe 100.00 Rmt 72.65

(SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

79 Providing, laying and jointing in true line and level 160 diametre U.P.V.C 100.00 Rmt 834.38

(Type B) conforming to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp

of the size 160 mm diametre x 210 mm length x 196 mm heigh at every

2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of

80 Providing, laying and jointing in true line and level 110 diametre U.P.V.C 112.00 Rmt 878.57

(Type B) conforming to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp

of the size 110 mm diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of

81 Providing, laying and jointing in true line and level 75 mm dia. UPVC 48.00 Rmt 758.51

SWRType B pipe conforming to IS 13592-1992 with one end plain and

other end socketed with rubbering and fitting conforming to ISI 14735-1999

of approved make for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp at every 2000 mm c/c or shall be conceled in walss as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of

82 Providing and fixing in PVC SWR cowel went 75mm dia to pipes. (B) 4.00 Nos. 16.16

83 Providing and fixing in PVC SWR cowel went 110mm dia to pipes. (B) 12.00 Nos. 29.29

84 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 32.00 Nos. 599.64

diameter with jali of the following nominal diameter of self cleansing design

with C.I scread down or hinged grating including the cost of cutting and

making good the walls.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

85 Providing and fixing wash down water closet (European type W C pan) with 9.00 Nos. 2905.77

integral P and S trap including jointing the trap with soil pipe in cement

mortar 1:1 (1 cement five sand) including providing and fixing plastic seat

cover for wash down WC with CP brass hinges and rubber buffers back

plastic seat with a pair of C I or MS bracket with complete fitting such as

lead valve siphon 15 mm dia brass ball valve with polythene float CP brass

handle unions and couplings for connection with inlet out let and over flow

pipes 40 mm dia porcelain enameled flush bend including cutting holes in

walls and making good the same connection the flush bend with cistern and

closet vitreous china.

86 Provision and fixing water closet squatting orissa type W.C. pan size 6.00 Nos. 1827.09

580mm integral footrest and 100 mm P or S trap and in cluding 25 mm dia

CP brass flush valve and GI inlet connection etc. comp. (A) Vitreous china

long pattern white or color.

87 Providing and fixing stainless steel grab 22 cm x 60 cm on door and 4.00 Nos. 1492.78

handicapped toilet including all fixture and accessary etc completed as per

directed engineer in charge.

88 Providing and fixing ball cock of approved. quality as directed. (A) Copper 2.00 Nos. 189.84

Metal (ii) 50mm dia.

89 Providing and fixing washbasin with single hole for pillar tap with C.I. or 17.00 Nos. 2179.58

M.S. brackets painted white including sutting holes and making good the

same including Brass waste and M I fisher union fittings including pvc

connection and waste pipe & all necessary fittings For All Floor (A)

Vitreous China: (ii) Flat Back washbasin 550 mm x v 400mm size. (i) In

90 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior 17.00 Nos. 859.41

glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to

wooden pluge with C.P. brass screws and washers.

91 Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets 17.00 Nos. 616.42

fixed to wooden plugs with C.P. brass scews. (B) 600mm x 20mm size.

92 Providing and fixing screw down bib taps of following size. (A) Brass screw 24.00 Nos. 186.83

down bib tap polished bright. (i) 15mm dia.

93 Providing and fixing Urinal of approved quality including connection with 8.00 Nos. 1628.53

trap and with integral longitudinal flush pipe. (A) Squating plate pattern

white earthenware 550mm x 300mm.

94 Providing laying (to level or slopes) and jointing reinforced concrete Light 518.00 Rmt 678.02

duty non-pressure pipes I.S. class NP2 of the following internal diameter

with collars and butt ends prepared for collar joints including testing of

joints complete. (D) 300mm.

95 Providing and fixing S.W. gully trap with C.I. grating brick masonry 8.00 Nos. 1246.92

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight (i) Square mouth traps (B) 150mm x 100mm

size P or R type.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

96 Constructing brick masonry chamber for underground C.I. Inspection 28.00 Nos. 3223.92

chamber and bends with briocks having croshing strength not less than

35Kg. Cm2 in C.M. 1:5 precast RCC cover 455mm x 610mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete etc. complete

(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line.

97 Constructing brick masonry chamber for underground C.I. Inspection C.I. 24.00 Nos. 3933.95

Inspection chamber and bends with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete etc. complete

(i) Inside dimensions 500mmx 700mm and 450mm deep for single pipe line.

98 Extra over items for every additional depth of 0.1M. of part thereof beyond 12.00 Nos. 242.39

450mm depth for Brick masonry chamber. (i) for 455mm x 610mm size.

99 Extra over items for every additional depth of 0.1M. of part thereof beyond 12.00 Nos. 264.86

450mm depth for Brick masonry chamber. (i) for 500mm x 700mm size.

100 Providing and fixing MS Ladder of required pattern with MS flats 500.00 Kg 102.01

(30x3mm) or round or square bars (12mm) at required spacing & with round

headed bolts and nuts or screws or welding including primer coat of

approved quality and two coats of oil paintas as directed by engineer in

101 Constructing drinking / Handwash Platform of 18 mm thick Polished Black 12.00 Sqmt 5248.97

Granite having 0.45m width and 0.60m height including 0.60m support at

every 0.7m c/c with cementing Materials / adhsives including makeing

necessary grooves in walls with all labour material of approved quality incl.

full moulded round front edge granite strip of one side polished and jointed

with grey cement slurry including rubbing and polishing etc. complete for all

102 Providing and fixing in position 300 mm high, 150 mm wide English letters 60.00 Nos. 1333.20

made from 1.0 mm thick stainless steel sheet as directed by Engineer in

charge with all necessary tools & plants etc. complete.

103 Providing and fixing in position 150 mm high, English letters made from 1.0 150.00 Nos. 686.80

mm thick stainless steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

104 Providing & Fixing 114mm wide G.I. Sheets lovers having weight not less 27.00 Sqmt 7206.35

than 490 Gm/m roll formed to create 84mm wide louver snap fixed on

special shaped GI channel. Fix louvers & channels shall finished with

powder coating of 55 micron (1) 0.55mm thick sheet.etc. complet as per

detail drawing as directed.

105 Providing and Fixing a set of wall mounted 38 mm dia U shaped horizontal 10.00 Nos. 2671.45

stainless steel collapsible grab bar, 38mm vertical stainless steel fixed grab

rail of grade SS 304 from round pipe supported and 75 mm dia 8 mm thick

SS 304 base flange on wall including anchor fasteners, nuts, accessories as

per detailed drawing etc. complete as directed by Architect or Engineer in

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

106 Providing and fixing MS Z clamp on Wall or celling for Pipe Fitting 164.00 Nos. 85.85

including all type necessary fittings and accessory etc. completed as per

directed engineer in charge.

107 Charges for making holes from 50mm to 160 mm dia in RCC wall, slabs or 30.00 Nos. 858.50

any other RCC members or Brick work by diamond core cutting machine of

HILTI or equivalent including disposing the debris. For all floors.

108 Providing and fixing coloured self adhesive PU-Tactile tile, ground surface 99.00 Sqmt 4586.41

indicators of Polyurethane) of size 300mm x 300mm for guiding/warning to

the visually visitors in the centre/side of the pedestrian/approach pathway as

per specification and guidelines complete in all respect to the entire

satisfaction of in charge.

109 Providing and fixing acrylic multilingual Braille (raised dots) 40.00 Nos. 1696.80

DIRECTIONAL SIGNBOARDS of size 225 x 150mm designed as per

accessibility standards and having 3.5mm thick acrylic base plate with

Upper Case San Serif words made of white acrylic non glare cut out letters

of height 15mm raised not less than 0.8mm above base plate and the

equivalent word written in Hindi with Devanagari non glare acrylic letters of

height 15mm raised not less than 0.8mm above base plate and having a non-

glare acrylic cut arrow pointing in the required direction. Each signboard to

be fixed as per manufacturers specifications on the wall at the approved

location and at a height of 1200mm from FFL complete as per design /

specifications and guidelines as per the entire satisfaction of the Engineer-in-

110 Providing & Fixing tactile layout plan of size 900mm x 600mm as approved 3.00 Nos 33027.00

design, made of 3.0mm thick acrylic non glare base plate and non glare cut

out symbols with Braille on which individual facility points, like inquiry,

reception, restrooms, medical room / first aid, cafeteria or breakout area,

lounge, meeting room, conference room etc. present the respective floors

with pictograph wherever needed all in tactile raised by minimum of 1.0mm

to 2mm in various colours to make it legible for seniors, partial vision

impaired etc. All the facility names should be in Braille, along with English

or Hindi. The entire block of tactile signs should be mounted on wall for

easy reading. The map to be installed at specified locations and installed at a

height of 800mm from ground level complete in all respect as per

Harmonized guideline & satisfaction of Engineer in charges.

111 Providing and fixing of acrylic, non-glare, tactile audio pictorial building 2.00 Nos 43480.50

layout as per the approved size, design and make, having 3mm thick acrylic

non glare base plate of the approved colour and non-glare acrylic cut out

symbols raised 3mm above base plate and Grade 2/ Grade 1 Braille to be

integral with the sign face and be raised 0.5mm above base plate. The map

to be installed at the specified location as per accessibility standards, shall be

oriented to the position of the viewer and to be installed at a height of

mm from the finished ground/ floor level and using the necessary hardware

specified by the manufacturer and to be installed up to the height of

mm from the finished ground/ floor level and using the necessary hardware

specified by the manufacturer and to be installed complete as per

design/specifications and guidelines as per the entire satisfaction of the the

Engineer-in-charge.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

112 Providing & fixing Braile indicator of size 170 mm x 35mm for handrails of 60.00 Rmt 820.12

the approved design and make have braile dots raised 0.5 mm above base

plate to be installed at specific locations as per direction of engineer in

113 Providing and fixing of conspectus tape 50mm width on of treads in 50.00 Rmt 1247.35

staircase including cutting pasting etc. As per harmonised guidelines

complete in all respect to the entire satisfaction of engineer in charge.

114 Providing and Fixing 15 mm thick 300 mm x 300 mm Tactile Warning Tiles 30.00 Sqmt 1208.97

(Attention Tiles i.e. Tactile Warning Surface Indicator {TWSI}) of Johnsan

Endura Tac Button Yellow Plus or equvqlent make in flooring laid on

mm thick cement mortar 1:6 (1 cement : 6 coarse sand) on new surface and

jointed with cement slurry including finished with flush pointing & cleaning

the surface for all floors as per detailed drawing etc. complete as directed by

Architect or Engineer in charge. Thse tiles shall be Anti Skid, Chemical

Resistant, Fade Proof, Frost - Heat & Weather Proof, High Flexural

Strength, Highly Durable, Stain Resistance. All Tactile Warning Tiles meet

the specific size and dimension standards as required by ISO/FDIS

115 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having 1.00 No. 958.17

weight not less than 35Kg.

116 Providing & erecting open well horizontal mono block pump set with cast 1.00 No. 39632.40

iron body, complete for three phase submersible motor having [H]For

H.P,3 phase open well horizontal mono block pump set suitable for

LPM to 1140 LPM @ 20 to 39 MTR head suitable for 65/80 mm dia

117 Supplying & erecting approvedmake 3 phase motor control cubicalpanel 1.00 No. 19695.00

(Star-Delta) made from 16G.CRCA sheet duty painted with epoxy powder

painted inside and outside with hinged doors and locking arrangement,

consisting suitable size of ON-OFF isolator (AC- 3/23duty) main fuses,

single phasing preventer cum water level, Guard (Compe unit), Toggle

switch to by pass Single phase preventercum WLG, indicating lamps forR-Y-

Bphases, over load relay.Automatic water level controller, Ammeter

&Voltmeter each with two way selector switch incoming wires duty socket

Crimped, Panel to be erected on angle iron frame grouted on wall as

overload relay, thermal / Electronics star delta cutoff timer, start-stop push

buttons. The isolator overload relay &cntractors of L&T, Siemens or Cuttler

Hamer make only. Panel to be erected on angle iron frame ground on wall

(e)S/D upto 2.5 H.P.

118 Providing and laying 60 x 60 cmMachine cut polished Blue kota stone slab 38.00 Sqmt 1015.53

flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-

coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and

jointed with grey cement slurry mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete. (A) 25mm thick.

119 Providing and laying polished 60 x 60 cm Machine Cut polished Blue kota 3.00 Sqmt 1144.15

slab 25mm thick in risers of steps, skirting Dedo and pillars laid on 10mm

thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray

cement slury mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

120 Providing and fixing rolling shutters of approved make made of 80 mm wide 5.00 Sqmt 3554.40

M.S laths inter-locked together through heir entire length and jointed

together at the ends by end locks mounted on specially designed pipe shaft

with bracket plates, guide channels and arrangement for inside and outside

locking with push-pull operation including the cost of hood cover and sprig

etc.complete (A) Shutters having width below 3.5M.

121 Drilling pilot borehole of size 250/300 mm at above site by mud flush direct 100.00 Rmt 853.25

122 Reaming of 250/300 mm dia. Pilot borehole to size 550 mm dia. Incliding 15.00 Rmt 527.95

assembling, lowering housing, casing strainerpipers with gravel packing and

clayball packing etc.

123 Development of cach water bearingzone coming across the full depth of 1.00 Job 13212.90

tubewell by lowering 100 mm dia. Droplineand 32 mm dia airline for each

water bearing Zone with suitabale capacity air compressar up to avilability

of sand free discharge.

124 900 CFM /200 PSI capacity air compressar upto the availability of sand free 1.00 Job 27206.17

discharge for upto 250 mtrs.

125 Supply of M.S. E.R.W. plain end medium duty pipe confirming to IS 100.00 Rmt 2440.64

4270/2001 with latest amendments of size 250 mm dia (minmum thicknes of

126 Screen Slotting of MS ERW balnce pipe with size of slot 6.75 cm X 6.35 cm 200.00 Slots 0.22

X 3.12 mm for 250 mm dia pipe.

127 Supply of miscellenious bore material suitable to 250 mm dia pipes as 1.00 Pair 1912.70

following (A) MS Bore clamps made from M.S. plate with 3 holes on either

side with nuts & bolts of std make of size 900X100X16 mm flat suitable for

250 mm dia pipe.

128 Supply of miscellenious bore material suitable to 250 mm dia pipes as 1.00 No. 1385.64

following (B) MS Bore Plug having 100mm height made from M.S. plate

with 3 holes at equal distance on circumferrence for nut-bolts type, locking

arrrangement with nuts-bolts & lock nuts of std make complete from 5 mm

thick M.S. plate suitable for 250mm dia pipe.

129 Supply of miscellenious bore material suitable to 250 mm dia pipes as 1.00 No. 999.90

following (C) MS Bail Plug having length 0.45 mtr from medium class pipe

as per I.S. suitable for 250 mm dia pipe.

130 Supply of miscellenious bore material suitable to 250 mm dia pipes as 168.00 No. 86.21

following (D) Steel bent plate suitable for ERW pipe for 250mm dia

(size:200 X 150X6 mm)

131 Supply of GRAVEL OF selected size 4 mm to 6mm. 40.00 Cum 2020.24

132 Electrologging of Pilot bore hole with carting. 1.00 Job. 10665.60

133 Geohydrological ground water investigation including vehicle charges for 1.00 No. 14220.80

three phase DTH bore / DR tube well including water sample testing &

chemical analysis.

134 Providing, supplying and commissioning ISI mark CI D/F Reflux Valves of 1.00 No. 4753.30

following class and diameter including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading, unloading, conveyance

to departmental stores stacking etc. complete. Reflux valves PN 1 IS

with ISI mark size: 100 mm.

135 Providing and laying in trenches galvanised mild steel tubes (Midium grade) 100.00 Rmt 919.80

of the following nominal bore, and tube fitting (Earthwork in trenches to be

measured and paid for separately (H) 80mm.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

136 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse 3.00 Nos. 11042.74

sand : 4-graded stone aggregate 20mm nominal size) foundation concrete

1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside

plastering 15mm thick with Cement Mortar 1:3 (1-Cement : 3-coarse sand)

finished with a floating coat of neat cement and making channels in cement

concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm

nominal size) finished smooth complete including curing and festing (i)

Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with

frame size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.) (A) With

230mm thick walls of brick msonry using brick having crushing strength not

less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5- Coarse sand)

(1) A type depth 0.90 Metre for 150mm diameter sewer.

137 Providing and fixing and floor 10.0 Kg. F/Cm2 working pressure poluthene 150.00 Rmt 339.05

pipes of the following outside Dia. Low densidy, complete with special

falnge compression type fittings, wall clips etc. including making good the

wall ceiling and floor.(G)110 mm.

138 Providing and fixing and floor 10.0 Kg. F/Cm2 working pressure poluthene 20.00 Rmt 696.90

pipes of the following outside Dia. Low densidy, complete with special

falnge compression type fittings, wall clips etc. including making good the

wall ceiling and floor. (G)180 mm.

139 Providing junction for rain water juncton chamber of size 0.60x0.60x0.75m 2.00 Nos. 9404.11

with excavation of size 1.96x1.96 m & 0.15m thick c.c.1:2:4 bed concrete

including brick masonary wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside & 1.06x1.06 RCC (1:2:4)

slab of thickness 0.15m with CRS steel and 0.60mx0.45m cast iron manhole

cover with frame weight not less than 35 kg as per directed by Engineer-in-

140 Providing and installation Recharge pit of “RAIWOHA” Make 3 layer RCC 1.00 No. 109645.60

Precast Injection well system of size 1.5 meter Dia. X 3.4 Meter Height rein

forced concrete precast three layer module with 6” dia x 12” dia. V wire

screen of 0.75mm x 1.0 mm Slot size in SS 304 material and 1.0 meter

height with MS Top cover and required Air vent including all necessary

excavation and transportation at site including required filter media for the

recharge system as per site requirement.

141 Drilling of min. 250 mm dia. bore hole in all strata including dualover 50.00 Rmt 1252.32

burden strata by combination DR/DTH rig including lowering 200 mm dia

MS ERW pipes in bore hole and testing etc. all work as per directed

engineer incharge.

142 Supplying slotted PVC pipes of approved quality at site of work confirming 50.00 Rmt 555.50

to IS. 1239/1974 180mm dia.

143 Construction of granular sub-base 150 mm thick by providing coarse graded 112.50 Cum 1151.40

machine crushed B.T. material satisfying MOST specification of grading I

(B.T. stone aggregate 53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm - 45 % and

2.36 mm below - 20 %) including spreading in uniform layer with motor

grader on prepared surface, mixing by mix in place method with rotavator at

OMC and compacting with vibratory roller to achieve the desired density

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

144 Steel work, welded in built up sections framed work including cutting, 4018.00 Kgs. 91.08

hoisting, fixing in position and applying a priming coat of read lead paint &

two coat oil paint. (A) In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross beams. Hip and jack

rafters, purlins conneted to common rafters and the like.

145 Providing and fixing of Ridge flashing for roof panel shall be made out of 110.00 Sqmt 867.39

0.5 mm thick pre coated GI sheet. The Precoated sheet shall be of minimum

240 mpa steel grade confirming to IS 14246:1995 and shall have zinc

coating of minimum 120 gsm as per IS:277:1992, 5-7 microns epoxy primer

on both side of the sheet and polyester top coat 15-18 micron. The PPGI

Sheet shall have plastic protective guard film of minimum 25 microns to

avoid scratches during transportation. The ridge shall be fixed to the steel

members by pop rivet or self drilling / self stitching fastners @ maximum

450 mm c/c along length of capping / flashing etc complete.

146 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete 293.00 Sqmt 706.93

block 60mm thick with grade of concrete M300 pnumatic compressed /

vibrated mechanically and as per approved design Confirming to IS 15658 :

2006 including 35 mm Sand layer for levelling and filling the joint with

sand in proper line and level as per guidlines of IRC : SP 63-2018 etc.

147 Providing and fixing pre-cast concrete kerb stone of gray cement based 183.00 Rmt 374.92

concrete block 30cm ength,30cm height and 15cm thick of M250 grade

concret as per approved design and including excavation for fixing in proper

line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

148 Box cutting the road surface to proper slope and camber for making a base 317.00 Cum. 109.41

for road work including removing the excavated stuff and depositing on the

road side slope as directed upto upto All lift and lead.

149 Providing, laying and compacting natural sand & gravel [C.B.R. not less 45.00 Cum. 344.41

than 20%] below sub base course including carriage of materials spreading

in uniform layer manually on prepared base and compacted with vibratory

roller to achieve desired density including all materials, labour etc. complete.

150 Providing and laying wet mix macadam base course 250 mm thick in two 131.00 Cum. 1196.85

layers using machine crushed B.T. chips as per required gradation mixing

with required optimum quantity of water, conveying the mix to site of work,

spreading in to grade and camber with mechanical paver and consolidation

each layer with vibratory roller including cost of material labour plant and

equipment etc. complete.

151 Compaction and finishing of cement concrete road by trimix process 426.00 Sqm 65.65

providing extra Labour charges for the trimix vacume dewatering service

process on cement concrete road sutface by using vacuum dewatering pump

floater surface vibrator including making groves and rough finish to surface

including leveling etc complete.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

152 Providing and fixing concertina coil fencing with punched tape concertina 112.00 Rmt 834.26

coil 600 mm dia 10 mt openable length having 50 no rounds per 6 mt length,

upto 3mt height of wall with existing angle iron (50mm x50mm x5mm)

requird shaped As per Directed Engeenier in charge. placed 2.4mt or 3.00mt

apart and with 4 horizontal R.B.T. reinforced barbed wire (3 mm), stud tied

with G.I. staples and G.I. clips to retain horizontal, including necessary bolts

or G.I.barbed wire tied to angle iron, all complete as per direction of

Engineer-in-charge, with reinforced barbed tape (R.B.T.) / Spring core (2.5

mm thick) and weight 43.478 gm/meter at compound wall for ESR M4/

153 Constructing providing and fabricating cattle guard using channel section 8.00 Sqmt 5168.17

frame of size ISMC series 100 mm x 50 mm (Weight 9.20 kg/Rmt) and

ISMC section 100 mm x 75mm (weight 11.50 kg/Rmt) intermediate support

for welding G.I.pipe at 12 Cm C/C of size 50 mm in a frame made of

Channel section size 100 mm x 50 mm all round including fixing the unit on

prepared chamber of masonary wall using MS hold fast embeded in

masonary wall top as directed by Engineer in charge and as per drawing and

necessary required arrangement etc complete.

154 Supply, installation, testing & commissioning of ISI approved electrical 1.00 No. 68680.00

motor driven jockey pump set having 450 LPM @ 50m head. The pump unit

shall be a horizontally direct mounted motor. Unit shall comprise the

following minimum requirements: a) Pump, b) Electric motor IE2, c)

Foundation bolts, d) Mating flanges with gasket and fasteners, e) Discharge

gauges, etc. complete in all respect, with labour, with GST.

155 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, 120.00 Rmt 474.70

conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589

for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per IS:

part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for size

mm dia. above, flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc. Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc. Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved drawings, specicification and

direction of the Engineer-in-Charge, with all complete. 25 mm dia.

156 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, 30.00 Rmt 1989.70

conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589,

for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per IS:

part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for size

mm dia. above, flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc. Hydrostatic testing for 2 hour's at 150% of the system pressure,

hook-up etc. Painting for piping, fittings & structural pipe support, shall be

two coat of zinc primer and two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved drawings, specicification and

direction of the Engineer-in-Charge, with all complete. 100 mm dia.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

157 Design, Supply and installation of Safety Signage made of Zinc Sulphilde 10.00 Sqmt 3787.50

based glow in dark, Rigid sheet with High Luminous property enclosed in a

transperent weather proof UV stabilized plastic pasted on 3 mm thick clear

acrylic sheet such as EXITS, EMERGENCY EXIT, DO NOT USE LIFT

DURING FIRE, FLOOR MARKINGS, FIRE LIFT, STAIRCASE EXIT,

FIRE ALARM CALL POINT, FIRE HOSE REEL, FIRE HYDRANT

158 Supply, installation, testing & commissioning of pressure switch. (Range 0 1.00 No. 3333.00

159 Supply, installation, testing & commissioning of 150 mm dia. dial Burdon 2.00 Nos. 3232.00

Type Glycerine Filled pressure gauge with isolation ball valve arrangements

with necessary isolation valves with all complete. (Range 0 to 15 kg/cm2).

160 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly 3.00 Nos. 3686.50

valve according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. &

below Lever operated and above 150 mm dia. Gear operated complete with

mating flanges /ANSI class # 150 with bolts & nuts washers, rubber gaskets

3 mm thick, etc., with all complete.

161 Supply, installation, testing & commissioning of SG iron body SinglePlate 1.00 No. 2121.00

Wafer Type NRV conf. to ASTMA 536, PN-1.6 complete with mating

Flanges class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc.,

with all complete. Accessories

162 Supply, installation, testing & commissioning of Two way fire brigade Inlet 1.00 No. 6019.60

connection with 63 mm dia. stainless steel (SS304) instantaneous male inlets

with built in non return valve in each inlet with 100 mm dia. header pipe,

suitable rubber cap and GI chain including nuts, bolts, washers, gasket 3 mm

thick, etc. with all complete.

163 Supply, Installation, testing & commissioing of Swinging type mild steel 2.00 Nos. 8736.50

hose reel drum with 20 mm dia. x 30 Rmt. rubber hose as per IS: 884. The

mounting stand shall be of mild steel and the hose shall be fitted with a SS

shut-off nozzle & SS ball valve of 25 mm dia. including supporting

arrangement with all complete. accessories.

164 Supplying, fixing & testing of of SS ball Valve 10 mm dia. 1.00 No. 565.60

165 Supplying, fixing & testing of of SS ball Valve 15 mm dia. 2.00 Nos. 666.60

166 Supplying, fixing & testing of of SS ball Valve 20 mm dia. 3.00 Nos. 787.80

167 Supplying, fixing & testing of of SS ball Valve 25mm dia. 1.00 No. 833.25

168 Supply, Installation And Commissioning Of Hose Nipple with Pipe Clamp. 6.00 Nos. 353.50

169 Filling of Gaps Between pipe and Core Cutting Hole With Chemical and 12.00 Nos. 454.50

170 Supply, fabrication and erection of Structure MS Material as like Angle, C 100.00 Kgs. 101.00

channel, I Beam Etc.

171 Supply, installation and commissioning of Copper Flexible cable for 7.5 HP 60.00 Rmt 222.20

Motor - 4 sq mm x 3 Core.

172 Supply and Fitting Change Over Switch (GEB/DG) 1.00 No. 9090.00

173 Supply, Filling and Fixing of approved make ABC type fire extinguisher - 6 4.00 Nos. 2323.00

Kg. Capacity as per IS:15683 & IS :

174 Supply, Filling and Fixing of approved make CO2 type fire extinguisher 6.00 Nos. 6514.50

Capacity 4.5 Kg. (conforming to IS-15683).

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

175 Submitting the application to obtain Fire NOC for one year to SMC 1.00 No. 50500.00

Department, Providing complete practical demonstration of fire system in

presence of fire officer and Submitting the photographs of demonstration,

refilling and testing certificates of fire extinguisher, Obtaining and providing

certificate of FPCOR, Payment of NOC Fees to SMC Department, Preparing

the documents of Affidavit and AMC with Notorization And Submitting to

Department, follow up to receive NOC And Providing to R & B Including

all above expenditure.

176 Supply, Installation and commissioning of Fabricated Stair case made up of 1.00 Set. 101000.00

MS angle and channel for emergency exit.

177 Supply, Installation and commissioning of Fire Alarm Panel Conventional 2.00 Nos. 22725.00

type, 2 zone with complete accessories.

178 Supply, Installation and commissioning of Audio hooters with complete 8.00 Nos. 1262.50

179 Supply, Installation and commissioning of Manual Call Points with 8.00 Nos. 1191.80

complete accessories.

180 Cable (Armour) for Fire Alarm system. 120.00 Rmt 111.10

181 Core cutting in wall and in RCC slab with size 50 mm dia. hole. 8.00 Nos. 505.00

182 Core cutting in wall and in RCC slab with size 150 mm dia. hole. 8.00 Nos. 757.50

183 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 203.00 Pt. 485.81

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected with

6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D. Connector as directed. (f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling complete Cat.III.

184 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 70.00 Pt. 674.68

both are of ISI marked 1.1 KV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following type erected on

PVC / Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling as

per pipe erected with necessary ceiling rose / H.D.Connector as directed. (f)

with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete.Cat.III.

185 Point wiring for on board Looped Plug with 6A Modular type switch & 5 76.00 Pt. 257.55

pin socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules erected on /

in wall / ceiling with following type accessories Cat.III.

186 Providing following type of Modular Type Accessories mounted with PVC / 10.00 Ea 151.50

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (1) One No.SP 6 Amp.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

187 Providing following type of Modular Type Accessories mounted with PVC / 10.00 Ea 151.50

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (2) One No 5 pin plug

188 Providing following type of Modular Type Accessories mounted with PVC / 44.00 Ea 160.59

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as

per site situation directed by Engineer In charge. (3) Two Pin/RJ-11

Telephone Socket [A] For One Gang Cat.III.

189 Providing following type of Modular Type Accessories mounted with PVC / 85.00 Ea 25.25

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (7) Blank Plate Single

190 Providing following type of Modular Type Accessories mounted with PVC / 2.00 Ea 160.59

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (8) Computer RJ-45 socket

191 Providing following type of Modular Type Accessories mounted with PVC / 24.00 Ea 180.79

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (9) 16 Amp. SP one way

switch Cat.III.

192 Providing following type of Modular Type Accessories mounted with PVC / 24.00 Ea 199.98

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (10) 6/16Amp. Universal

socket Cat.III.

193 Providing and erecting ISI mark Medium class RIGID PVC PIPES of 225.00 Mtr. 24.24

following size complete to be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed (a)

194 Supplying and laying UPVC cable trunking system comprising unplasticised 30.00 Mtr. 277.75

polyvinyl, chloride rigid material with ignition free and flame proof

confirming BS with necessary end caps Internal and external bend, flat

bends, coupler, tee etc. All necessary accessories and measuring of

following sizes (1) 75 mm x 50 mm trunking.

195 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 2268.00 Mtr. 82.82

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (A) With medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm.

196 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 528.00 Mtr. 112.11

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

197 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 360.00 Mtr. 260.58

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories (h) 4 wire 6 sq. mm.

198 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte 172.00 Mtr. 56.56

multi stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

(Specifically for control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and bolts if required.

(e) One wire 6.00 sq. mm.

199 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte 16.00 Mtr. 300.98

multi stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

(Specifically for control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and bolts if required.

(e) One wire 6.00 sq. mm (i) One wire 35.00 sq. mm.

200 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 100.00 Mtr. 46.46

kv grade ISI marked copper wires of following size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed.

201 Supplying & erecting approved make Telephone Cable electrolytic copper 880.00 Mtr. 20.20

conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC

tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in existing pipe of

following size of conductors & eaof pairs With necessary connections. [A]

Conductor Size 0.5 mm (a) Unarmoured (2) Two Pairs.

202 Supplying & erecting approved make Telephone Cable electrolytic copper 55.00 Mtr. 467.63

conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC

tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in existing pipe. of

following size of conductors & eaof pairs With necessary connections. [A]

Conductor Size 0.5 mm (a) Unarmoured (2) Two Pairs (b) Armoured [Jelly

Filled] (3) Fifty Pairs.

203 Providing & erecting main Distribution (MDF) indoor type, back mounted 1.00 Ea 1747.30

frame as per DoT standard approved with krone strips (c) Suitable for

204 Supplying & erecting approved make LAN cable of following size in 64.00 Mtr. 47.47

existing pipe as per direction [C] CAT -

205 Providing & erecting Switch board for Computer or electric apparatus 40.00 Ea 1133.22

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered with

textured/metallic /white front plate, modules erected with necessary

connections as directed 1 no. 6A/16A universal plug-switch combined.

3 ea 6A Switch 3 ea 6A 5 pin Plug For Modular Type Accessories Cat. III.

206 Decorative call bell Ting-tong box type 250 volts complete erected. 10.00 Ea 71.71

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

207 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 2.00 Ea 165.64

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.9, THD

< 15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt, LED

LED driver efficiency > 85 % (fitting required LM-79 & LM-80

Certificates) (NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Tube Light with integral driver (i)

5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet Cat-lll.

208 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 12.00 Ea 373.70

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.9, THD

< 15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 % (fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Tube Light with integral driver (iv)

22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet Cat-lll.

209 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 67.00 Ea 535.30

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.9, THD

< 15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 % (fitting required LM-79 & LM-80

Certificates) (NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Tube Light with integral driver (v)

36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet Cat-lll.

210 Supplying and erecting led lamps with following wattage capacity of 220 to 16.00 Ea 112.11

240 voltage, minimum 15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22

lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder (ii) 5 to 8 watts Cat-III.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

211 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 16.00 Ea 758.51

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company mark/name 160V

to 270V, Power Factor more than 0.95, THD < 15 %, CCT 3000 K to

6500K, Luminaire efficacy> 85 lumens/watt, LED driver efficiency > 85 %

(fitting required LM-79 & LM-80 Certificates) (NOTE: Below description

have shown ranges of Wattage capacity of LED fittings. The Engineer

incharge may select any wattage capacity between the ranges shown.) (A)

Square/ Circular shaped Surface/Recessed Mount Downlight with provision

for spring loaded mounting clips complete. IP20 (iv) 22-24 watts, Surge-2

212 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 63.00 Ea 1794.77

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company mark/name 160V

to 270V,Power Factor more than 0.95, THD < 15 %, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % (fitting

required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.) (B) LED Panel

Light with provision for Plane front frame with translucent cover fixed to

housing complete. IP20 (vi) 36 watts, 24" x 24", Surge- 2KV Cat-lll.

213 Supplying and erecting LED street light / Flood light fittings with High 10.00 Ea 5976.17

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or embossed 160 to

270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %. (fittings required LM-79 & LM-80 certificates)

(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the

ranges shown.) (A) Street Light (IP-65), Surge protection -4KV integral and

Light must have 440VAC line supply with over-voltage protection. (A)

Street Light (IP-65), Surge protection -4KV integral and Light must have

440VAC line supply with over-voltage protection. (iii) Above 60 to 90 watts

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

214 Supplying and erecting LED street light / Flood light fittings with High 8.00 Ea 10818.11

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or embossed 160 to

V, Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt LED

driver efficiency > 85 %. (fittings required LM-79 & LM-80 certificates)

(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the

ranges shown.) (B) Flood Light (IP-65), Surge protection -4KV integral and

Light must have 440VAC line supply with over-voltage protection. (vii)

above 200 to 250 watts Cat-lll.

215 Supplying and erecting LED street light / Flood light fittings with High 10.00 Ea 4819.72

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or embossed 160 to

270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (C) Post Top Lantern LED fitting

comprises of finish cast aluminum spigot and spun aluminum canopy fixed

with opal polycarbonate, pipe arrangement for vertical mounting driver and

accessories wired upto terminal block.IP 65 (ii)32-40W Cat-lll.

216 Providing and erecting Approved make Four pole moulded case circuit 5.00 Ea 8055.76

breaker having breaking capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S. housing ICS=100% of

ICU only Cat III.

217 Providing and erecting Approved make Four pole moulded case circuit 3.00 Ea 16221.61

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S. housing ICS=100% of

ICU only Cat III.

218 Supplying & erecting approved make Four Pole 415V change over switch 1.00 Ea 7790.13

interior for panel mounting with operating mechanism A.C.23 duty

confirming to IS for (C)100-125A Cat-lll.

219 Supplying & erecting approved make Four Pole 415V change over switch 1.00 Ea 12241.20

interior for panel mounting with operating mechanism A.C.23 duty

confirming to IS for (D)200A Cat-lll.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

220 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 2.00 Rn.Mtr 1961.42

Copper Busbars with four equal ea of electrolyte bus having current density

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

carrying capacity, erected with necessary bus bar supports /insulators, main

cable socket to each bar, erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity.

221 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 2.20 Rn.Mtr 3202.71

Copper Busbars with four equal ea of electrolyte bus having current density

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

carrying capacity, erected with necessary bus bar supports /insulators, main

cable socket to each bar, erected in existing cubical panel with necessary

connections. (B) Suitable for 200 Amp. capacity.

222 Providing and erecting Miniature circuit breaker single pole 6A to 25A 100.00 Ea 112.11

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

223 Providing & erecting 240 V MCB double pole switch for lighting Load (B 7.00 Ea 295.93

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing

box having following capacity (B) 40 Amp. Cat.III.

224 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B 22.00 Ea 638.32

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity (b)40 Amp. Cat.III.

225 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load 2.00 Ea 737.30

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity (c)63 Amp. Cat.III.

226 Providing and erecting Sheet Steel powder coated MCB distribution board - 6.00 Ea 2339.16

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate ea of MCBs. (The DBs should be used of same company of

MCB to be used) suitable for (B) three phase incoming and single phase

horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel

double door (i)4 way.

227 Providing and erecting Approved make RCCBs conforming to IS: 12640 18.00 Ea 2235.13

and having sensitivity of 30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected as

directed (ii) 40Amps. DP Cat. III.

228 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 8.00 Kg. 794.87

229 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. 62.00 Kg. 77.77

230 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. 11.00 Ea 368.65

dia. galvanised iron pipe with coupling and buch buried in specially

prepared earth pit complete with necessary 8 SWG earth wire.

231 For using salt and charcoal / coke as required for pipe type earthing. 11.00 Ea 171.70

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

232 Supplying & erecting earth pit of minimum bore dia.150mm size approved 3.00 Ea 4591.46

make earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly stamped

and signed by agency and officer Incharge has to ensure the value of

earthing resistane mentioned in test Certificate) & having back filling

compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm /

meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill Compound :- earthing

compound should be capable to retain moisture for long time Necessary test

report must be submitted by Agency.(a) For Electrical Installation up to

440V in normal soil Length of pipe - 1 Mtr Back filling compound - 1 Nos

233 Providing & erecting weather proof, dust & vermin proof, floor mounted 4.73 Sq.Mtr 10468.65

front operated indoor type cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories, supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting with internal partitions

& cable alley as per requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber grommets,

rib, bakelite control fuses/MCB for measuring instruments, earth bus &

earth bolts, foundation flange - bolts-base Plates, sufficient ea of hinged

doors, handles with locking arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary ventilation, earthing strip

complete. The Panel shall be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied with following approved

manufacturers with following size. (A) locally fabricated panel board (i)

with 350mm depth.

234 Providing , erecting , fabricating the M.S. structure as per requirement on 110.00 Kgs. 77.77

site incorporating proper size of M.S. angles, square, round, flats, bars,

channels, sections complete with cutting, welding, grinding & finishing duly

painted with one coat of red oxide with erection on site as per direction of

engineer in charge with necessary grouting, cementing, plastering &

finishing complete.

235 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 18.00 Mtr. 284.82

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables (C) 3 1/2 core 50 Sq.

mm (25 Sq.1/2 mm core)

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

236 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 138.00 Mtr. 378.75

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables (D) 3 1/2 core 70 Sq.

mm (35 Sq. mm 1/2 core)

237 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 809.00 Mtr. 126.25

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables (B)

4 core 6 Sq. mm.

238 Making trench in soft soil of suitable width of 90 cm deep for laying cable 470.00 Mtr. 55.55

or locating the fault all over the run and back filling the same and making

the surface as normal ground.

239 Supplying following size of Light duty “A” Class G.I . Pipe & erecting as 30.00 Mtr. 300.98

directed by Engineer-in-charge. (B) 50 mm dia.

240 Supplying following size of Light duty “A” Class G.I . Pipe & erecting as 12.00 Mtr. 696.90

directed by Engineer-in-charge. (D) 100 mm dia.

241 Providing & laying approved make Double walled corrugated pipes (DWC) 392.00 Mtr. 62.62

of polyethylene (conforming to IS 14930 II) with necessary connecting

accessories of same material at required depth in existing trench for laying

of cable below ground / road surface for enclosing cable (A) 50 mm outer

242 Providing & laying approved make Double walled corrugated pipes (DWC) 78.00 Mtr. 95.95

of polyethylene (conforming to IS 14930 II) with necessary connecting

accessories of same material at required depth in existing trench for laying

of cable below ground / road surface for enclosing cable (C) 90 mm outer

243 Providing and, fixing heavy duty flange type brass cable gland with rubber 21.00 Ea 38.38

ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (B) 2 to 4 core 6 Sq. mm.

244 Providing and, fixing heavy duty flange type brass double compression type 2.00 Ea 75.75

cable gland with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of cables. (B) 3 &

1/2 core 35/50 Sq. mm.

245 Providing and, fixing heavy duty flange type brass double compression type 5.00 Ea 103.02

cable gland with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of cables. (C) 3 &

1/2 core 70 Sq. mm.

246 Solder less crimping type Aluminium lugs conforming to IS suitable for 4.00 Ea 6.06

cable of following size evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5/ 2.5/4/6 Sq.mm.

247 Solder less crimping type Aluminium lugs conforming to IS suitable for 2.00 Ea 15.15

cable of following size evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated nut bolts in an approved

manner. (C) 16/25 Sq.mm.

248 Solder less crimping type Aluminium lugs conforming to IS suitable for 11.00 Ea 20.20

cable of following size evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated nut bolts in an approved

manner. (D) 35/50 Sq.mm.

249 Solder less crimping type Aluminium lugs conforming to IS suitable for 15.00 Ea 25.25

cable of following size evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated nut bolts in an approved

manner. (E) 70 Sq.mm.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

250 Providing and fixing approved make Perforated C type cable tray. Made 10.00 Rmt. 622.16

from sheet steel. The cable tray should be single or double bended as per

required and as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759 with max 17.5% perforation with coupler

plate / Fish plate and GI hardware like nut - bolt and washers etc. erection

with necessary support (included) as per Specification and as per instruction

of engineer in charge. (5) 300 X 50 X 2.0 mm Thick.

251 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan 70.00 Ea 1948.29

with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz

mm sweep complete having 3blades with aluminium blades with canopy &

30 cm. down rod erected with earthing. (Make shall be approved by

Engineer in charge).

252 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe 70.00 Mtr. 108.07

down rod erected duly painted for fan complete with proper insulation

without leakage and earthing.

253 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to 70.00 Ea 108.07

the RCC bars up to 50mm length each side and pierced through a 16 Gauge

M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

254 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan 70.00 Ea 18.18

255 Supplying & erecting approved make low noise decorative exhaust fan 17.00 Ea 1366.53

having square frame ABS body with inbuilt lowers & square frame. 250mm

with 1350 RPM Cat.II.

256 Supplying and erecting approved make Octagonal pole made from HR sheet 8.00 Ea 5556.01

steel. The pole should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed

with integral Junction box consist of terminal plate of min 6mm Hylam

sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud

type terminal and arrangement for cable termination to be erected With

Suitable foundation (Included) as per details given by manufacturer

considering site requirement.(B) 4 Mtr. Long 70 mm Top X 130 mm bottom

dia, 3 mm thickness with 200mmX200mmX12mm base plate, 4-M16 Bolts

and 450mm long with necessary G.I. J Bolts Approx weight 37 kg.

257 Supplying and erecting approved make Octagonal pole made from HR sheet 10.00 Ea 8192.11

steel. The pole should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed

with integral Junction box consist of terminal plate of min 6mm Hylam

sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud

type terminal and arrangement for cable termination to be erected With

Suitable foundation (Included) as per details given by manufacturer

considering site requirement. (D) 6 Mtr. Long 70 mm Top X 135 mm

bottom dia, 3 mm thickness with 200mmX200mmX12mm base plate, 4-

M20 Bolts and 600mm long with necessary G.I. J Bolts Approx Pole weight

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

258 Supplying & erecting approved make SMC press moulded composite FRP. 10.00 Ea 476.72

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way (3P+N+E), DIN rail for mounting mob & hinged doors as per

requirement having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable clamps& earth bolt

of following size of box. (C)150mm x 125mm x 100mm [deep].

259 Supplying and erecting Street light pole bracket comprising main B Class GI 10.00 Ea 491.87

pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I.

sleeve tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and bolts for fixing the

brackets and having spread of 0.5 mtr. Length with 110 deg.with vertical

plane and suitable welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base primer and two coats

of Aluminium / PU paint. paint with following ea of arms. [A] Single Arm

bracket 0.5 Mtr.

260 Providing & erecting water cooler having storage capacity 150 Ltr. & 2.00 Ea 55893.40

cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚C within a hour, The water cooler

should be comprising of hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by evaporating, coil, thermostats,

relay etc.complete with necessary inlet & outlet connection. The body of

water cooler will be made from Stainless Steel.

261 Supplying & erecting reverse osmosis (RO) water purification system with 1.00 Ea 93468.43

M.S. powder coated pedestal frame, prefilter housing carbon filter suitable

buster DC pump, auto low & high pressure switches with following size of

LPH capacity & erected as directed [E] 200 LPH with 1 phase / 3 phase Raw

water pump of 1000LPH @ 2.5kg/cm2 (1N0 - Kirloskar/CRI/Lubi) , Dual

media filter 10"x54" (1 No), Micron catridge filter 20" x 2.5" - (1No), High

pressure pump 1000LPH @ 10kg/cm2 - (1No - Shimge /CRI /Lubi) , RO

Membrane housing with RO membrane of 40*40 - (1 No), RO pressure tube

4" x 1E-(1No), 0-1200LPH Rotameter-(2 Nos). Recovery Rate 50%.

262 Supplying and erecting approved make panel mounting type Digital 2.00 Ea 1275.63

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected on

existing panel board with all connection, wiring etc. with manufacturers

calibration certificate.

263 Supplying and erecting approved make panel mounting type Digital 2.00 Ea 1558.43

Ammeter having 3 digits LED display, external CT operated, calibrated for

to 1000 Amps suitable to operate on 500 Volt AC, erected on existing panel

board with all connection, wiring etc. with manufacturers calibration

264 Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase 4.00 Ea 317.14

AC Supply 500 V on existing panel board with necessary connections.

265 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 6.00 Ea 274.72

1000/5 ratio 15 VA burden erected in existing CRCA box duly secured with

insulating materials connected to the meter.

266 Supplying and erecting approved make suitable panel indicator LED type 9.00 Ea 43.43

lamp, lens cover, complete erected with necessary connections.

Item Description of Item (with brief specification and reference to book Quantity Unit Rate In Amount

No of specifications) figures

267 Supplying & erecting approved make Digital time switch having lithium cell 1.00 Ea 3168.37

6 years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with floating

contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed

in fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

268 Supplying & erecting power contactor, AC3 duty for time switch complete 1.00 Ea 2782.55

erected as per direction Cat III (D) 4 pole 440V 40 Amp.

(Rupees Three Crore Seventy Seven lakh Forty Thousand Fifty Six and Thirty Eight Paise Only.)

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and words) of the

estimated rate mentioned above.

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge

for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills.

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.:PRC-10/2017

Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per

actual mix design the cost of difference of cement consumption have been deducted from the rate of original item at the

rate of input rate mentioned in all the tender.

5 GST will be paid Extra as per Govt. amendment.

Signature of Contractor Deputy Executive Engineer

Mandvi (R&B) Sub Division,

Executive Engineer Executive Engineer

Electric (R&B) Division, Surat (R&B) Division No.2,