Tender for the Work of Supply, Laying, Testing & Commissioning Of 11KV underground XLPE Cable (Cable to be supply by DGVCL) with Cable End Termination and Straight joint kit (to be supplied by the Contractor / Agency) and HDPE green Pipe for HT Underground Cable Work and Erection of HT-LT lines & T/C etc. for ND Scheme & ALL other Scheme within Jurisdiction of Umargam Ind. Sub division under Vapi Ind. Division.

(A) CAPITAL WORK LABOUR RATES FOR FY 2024-25 (WITHOUT GST)

Sr Item Code Description UNIT Rate

9926000001 HT TAPPING FROM THE EXISTING POLE INCLUDING FIXING OF CROSS NO.

ARMS, CLAMPS ANTI-CLIMBING DEVICES, DANGER BOARD, INSULATORS

ETC. COMPLETE AND PAINTING OF FABRICATED MATERIALS AND

1 NUMBERING COMPLETE WITH COST PAINTS AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY SET AND EARTHING.

9926000002 ERECTION OF PSC POLES OF 8METER 200 KG INCLUDING EXCAVATION OF NO.

PIT AND REFILLING OF EARTH, FIXING OFCROSS ARMS, TOP FITTING

CLAMPS ANTICLIMBING DEVICES, INSULATORS ETC.COMPLETE AND

2 PAINTING OF FABRICATED MATERIALS USED ON THE POLES AND

NUMBERING WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY SET AND

9926000003 ERECTION OF STEEL POLES OF 9 TO 11 METERS INCLUDING EXCAVATION NO.

OF PIT AND REFILLING OF EARTH, FIXING OF CROSS ARMS, TOP FITTING

CLAMPS ANTI-CLIMBING DEVICES, DANGER BOARD, INSULATORS ETC.

3 COMPLETE AND PAINTING OF STEEL POLE, FABRICATED MATERIALS USED

ON THE POLE AND NUMBERING WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY SET AND EARTHING.

9926000004 ERECTION OF STEEL POLE OF 13 METERS FOR RAILWAY CROSSING ON NO.

BG/MG/NG LINE FOR 0.400/11/22KV OVERHEAD LINES I.E INCLUDING

EXCAVATION OF PIT & REFILLING OF EARTH, FIXING CROSS ARMS, TOP

FITTING CLAMPS,ANTICLIMBING DEVICES DANGER BOARD, INSULATORS

4 ETC. COMPLETE AND PAINTING OF STEEL POLES, FABRICATED MATERIALS

USED ON THE POLES ANDNUMBERING WITH COSTOF PAINT AS PER

STANDARD SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS AND

9926000005 ERECTION OF DOUBLE POLE STRUCTURE OF 8 METERS 200 KG PSC NO.

POLES INCLUDING EXCAVATION OF PITS & REFILLING OF EARTHING,

FIXING OF CHANNELS, SUPPORTING ANGLES,CLAMPS, ANTI-CLIMBING

DEVICES DANGERBOARDS,INSULATORS ETC.COMPLETE AND PAINTING

5 OF FABRICATED MATERIALS USED ON THE POLES AND NUMBERING WITH

COST OF PAINT AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SETS AND EARTHING. (WITHOUT AB SWITCH)

9926000006 ERECTION OF DOUBLE POLE STRUCTURE OF 9 TO 11 METERS.STEEL POLE NO.

INCLUDING EXCAVATION OF PITS &REFILLING OF EARTH, FIXING OF

CHANNELS, SUPPORTING ANGLES,CLAMPS,ANTI-CLIMBING DEVICES

DANGER BOARDS, INSULATORS ETC.COMPLETE &PAINTING

6 POLES,FABRICATED MATERIAL SUSED ON THE POLES AND NUMBERING

WITH COST OF PAINTSAS PER STANDARD SPECIFICATION BUT

EXCLUDING ERECTION OF GUY SET ANDEARTHING. (WITHOUT AB SWITCH)

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

9926000007 ERECTION OF DOUBLE POLE STRUCTURE WITH MOUNTING OF AB SWITCH, NO.

HGFUSES OF 8 MTRS 200 KG PSC POLES INCLUDING EXCAVATION OF PITS

AND REFILLING OF EARTH,FIXING OF CHANNELS SUPPORTING ANGLES,

CLAMPS,ANTI-CLIMBING DEVICES, DANGER BOARDS, INSULATORS,DO

FUSES ETC. COMPLETE AND PAINTING OF FABRICATED MATERIALS USED

ON THE POLES AND NUMBERING WITH COST OF PAINT AS PER

STANDARD SPECIFICATION BUT EXCLUDING OF ERECTION OF

GUY SET AND EARTHING. (WITH AB SWITCH)

9926000008 ERECTION OF DOUBLE POLE STRUCTURE WITH MOUNTING OF AB NO.

SWITCH,HG FUSES, 9 TO 11 METERS STEEL POLES INCLUDING

EXCAVATION OF PITS AND REFILLING OF EARTH, FIXING OF CHANNEL,

SUPPORTING ANGLES, CLAMPS, ANTICLIMBING DEVICES , DANGER

BOARDS, INSULATORS, ETC. COMPLETE AND PAINTING OF POLES

FABRICATED MATERIALS USED ON THE POLES ANDNUMBERING WITH

COST OF PAINT AS PER STANDARD SPECIFICATION

BUTEXCLUDING ERECTION OF GUY SET AND EARTHING. (WITH AB

9926000009 ERECTION OF DOUBLE POLE STRUCTURES WITH MOUNTING OFAB NO.

SWITCH,FUSES, TRANSFORMERS, LIGHTENING ARRESTORS,

DISTRIBUTION BOX. OF 8 METERS 200 KG PSC POLES INCLUDING

EXCAVATION OF PITS AND REFILLING OF EARTH, CARTING OF

TRANSFORMERS FROM STORES TO SITE, FIXING OF CHANNELS,

SUPPORTING ANGLES,BRACINGS CROSS ARMS CLAMPS, ANTICLIMBING

9 DEVICES DANGER BOARDS,CONDUCTOR AND CABLE WIRING

ETC.COMPLETE AND PAINTING OF FABRICATED MATERIALS USED ON THE

POLES AND NUMBERING WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS AND EARTHING.

9926000010 ERECTION OF DOUBLE POLE STRUCTURE WITH MOUNTING OF AB NO.

SWITCH,HG FUSES TRANSFORMERS, LIGHTENING ARRESTORS,

DISTRIBUTION BOX 9 TO 11 METERS STEEL POLES

INCLUDINGEXCAVATION OF PITS & REFILLING OF EARTH CARTING OF

TRANSFORMERS FROM STORE TO SITE, FIXINGOF CHANNELS

10 SUPPORTING ANGLES, BRACING, CROSS ARMS,CLAMPS, ANTICLIMBING

DEVICES, DANGER BOARDS,CONDUCTOR AND CABLE WIRING ETC.

COMPLETE AND PAINTING OF POLES FABRICATED MATERIALS USED ON

THE POLES AND NUMBERING AS PER STANDARD SPECIFICATION BUT

EXCLUDING ERECTIONS OF GUY SETS AND EARTHING.

9926000011 ERECTION OF GUY SET INCLUDING EXCAVATION OF PITS & REFILLING OF NO.

EARTH AS PER STANDARD SPECIFICATION WITH STAY CLAMPS, STAY

11 WIRE, ANCHOR ROD, TURN BUCKLE, EYEBOLT, GUY INSULATOR, CEMENT

CONCRETE BLOCK ETC. BUT EXCLUDING CONCRETING.

9926000012 CONCRETING OF POLES, GUYS, ETC. INCLUDING COST OF CEMENT SAND CMT

12 METAL (1:2:4)AND WATER ETC. AS PER STANDARD SPECIFICATION.

9926000013 ERECTION OF COIL TYPE EARTHING INCLUDING COST OF COAL,SALT ETC. NO.

13 BUT WITHOUT COST OF Gl WIRE AS PER STANDARD SPECIFICATION(20kg

salt+20kg coal)

9926000014 ERECTION OF Gl PIPE/CI PLATE TYPE EARTHING INCLUDINGCOST OF COAL NO.

14 SALT ETC. BUT WITHOUT COST OF PIPE/GIPLATE Gl WIRE AS PER

STANDARDSPECIFICATION. (20k solt+20k coal)

9926000015 ERECTION OF STREET LIGHT FIXTURE COMPLETE WITH CLAMPS, BRASS NO.

NIPPLE, BRASS HOLDER TECK WOODBUSH,REFLECTORS FUSE,

15 WIRING ETC. AS PER STANDARD SPECIFICATION BUT EXCLUDING COST OF

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

9926000016 STRINGING OF ALL TYPE OF CONDUCTOR (EXCEPT DOG CONDUCTOR) ONECONDPER

16 FOR 11/22KV & LT LINES INCLUDING FIXING OF INSULATORS BINDING KM

17 9926000017 STRINGING OF Gl WIRE 8 SWG INCLUDING BINDING JUMPERING ETC. DO

9926000018 PROVIDING SINGLE PHASE SERVICE CONNECTION WITH- PVC 4MM TWIN NO.

CORECABLE FROM TERMINAL POLE TOMETERING POINT INCLUDING

18 FIXING OFMETER WITH METER EARTHING COMPLETE WORK AS PER

STANDARD SPECIFICATION BUT EXCLUDING COST OF MATERIALS.

9926000019 PROVIDING THREE PHASE 4 WIRE SERVICE CONNECTION WITH PVC NO.

4MM2/10MM2 FOUR CORE CABLE FROM TERMINAL POLE TO METERING

POINT INCLUDING FIXING OF METER WITH METER EARTHING COMPLETE

19 WORK AS PER STANDARD SPECIFICATION BUT EXCLUDING COST OF

9926000020 ADDITIONAL COST FOR EXCAVATION OF PIT IN HARD ROCK AREA FOR NO.

ERECTION OF POLE/ GUY ETC. AS PER STANDARD SPECIFICATION OVER &

ABOVE NORMAL COST COVERED AGAINST EXCAVATION OF PIT UNDER

20 NORMAL SOIL FOR ERECTION OF POLE,GUY, DOUBLE POLE STRUCTURE

EARTHING WITH THE APPROVAL OF SUPDT.ENGINEER.

21 9926000021 PROVIDING GUARDING TO HT LINE ON ROAD/ RAIL CROSSING. MTR

22 9926000022 PROVIDING GUARDING OF LT LINES ON ROAD/RAIL CROSSING. MTR

23 9926000023 LT LINE TAPPING- SINGLE PHASE NO.

24 9926000024 LT LINE TAPPING- THREE PHASE NO.

9926000025 LAYING OF OVER HEAD LT CABLE FOR ROAD CROSSING,HT LINE NO.

25 CROSSING AND TELEPHONE LINE CROSSING ETC.(PER SPAN)

9926000026 ERECTION OF SINGLE POLE STRUCTURESWITH, HG NO.

FUSES,TRANSFORMERS,LIGHTENING ARRESTOR, DISTRIBUTION BOX. ON

METERS 200 KG PSC POLE INCLUDING EXCAVATION OF PITS AND

REFILLING OF EARTH, CARTING OF TRANSFORMERS FROM STORES TO

SITE, FIXING OF CHANNELS, SUPPORTING ANGLES,BRACINGS CROSS

26 ARMS CLAMPS, ANTICLIMBING DEVICES DANGER BOARDS,CONDUCTOR

AND CABLE WIRING ETC.COMPLETE AND PAINTING OF FABRICATED

MATERIALS USED ON THE POLE AND NUMBERING WITH COST OF PAINT AS

PER STANDARD SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS

9926000027 ERECTION OF SINGLÉ POLE STRUCTURES WITH HG NO.

FUSES,TRANSFORMERS,LIGHTENING ARRESTOR, DISTRIBUTION BOX. ON

9 to 11 METERS RSJ POLE INCLUDING EXCAVATION OF PITS AND

REFILLING OF EARTH, CARTING OF TRANSFORMERS FROM STORES TO

SITE, FIXING OF CHANNELS, SUPPORTING ANGLES,BRACINGS CROSS

27 ARMS CLAMPS, ANTICLIMBING DEVICES DANGER BOARDS,CONDUCTOR

AND CABLE WIRING ETC.COMPLETE AND PAINTING OF FABRICATED

MATERIALS USED ON THE POLE AND NUMBERING WITH COST OF PAINT AS

PER STANDARD SPECIFICATION BUT EXCLUDING ERECTION OFGUY SETS

9926000028 ERECTION OF PSC POLES OF IO METER 270 KG INCLUDING EXCAVATION NO.

OF PIT AND REFILLING OF EARTH, FIXING OF CROSS ARMS, TOP FIITING

CLAMPS ANTICLIMBING DEVICES, INSULATORS ETC. COMPLETE AND

28 PAINTING OF FABRICATED MATERIALS USED ON THE POLES AND

NUMBERING WITH COST OF PAINT AS PER STANDARD SPECIFICATION BUT

EXCLUDING ERECTION OF GUY SET AND EARTHING.

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

9926000029 ERECTION OF DOUBLE POLE STRUCTURE OF 10 METER 270 KG PSC POLES NO.

INCLUDING EXCAVATION OF PITS & REFILLING OF EARTHING, FIXING OF

CHANNELS, SUPPORTING ANGLES,CLAMPS, ANTI-CLIMBING DEVICES

DANGERBOARDS,INSULATORS ETC.COMPLETE AND PAINTING OF

29 FABRICATED MATERIALS USED ON THE POLES AND NUMBERING WITH

COST OF PAINT AS PER STANDARDSPECIFICATION BUT EXCLUDING

ERECTION OF GUY SETS ANDEARTHING. WITHOUT AB SWITCH

9926000030 STRINGING OF IOOMM2 ACSR/100MM2 AAAC CONDUCTOR FOR HT/ LT ONE

LINES INCLUDING FIXING OF INSULATORS, BINDING JUMPERING ETC. COND

9926000031 STRINGING OF DOG CONDUCTOR FOR 11/22KV HT LINES INCLUDING ONE

FIXING OF INSULATORS, BINDING JUMPERING ETC. COND

9926000032 ERECTION OF DOUBLE POLE STRUCTURES WITH MOUNTING OF AB NO.

SWITCH,HG FUSES, TRANSFORMERS, LIGHTENING ARRESTORS,

DISTRIBUTION BOX. OF 10 METERS 270 KG PSC POLES INCLUDING

EXCAVATION OF PITS AND REFILLING OF EARTH, CARTING OF

TRANSFORMERS FROM STORES TO SITE, FIXING OF CHANNELS,

SUPPORTING ANGLES,BRACINGS CROSS ARMS CLAMPS, ANTI-CLIMBING

32 DEVICES,DANGER BOARDS, CONDUCTOR AND CABLE WIRING

ETC.COMPLETE AND PAINTING OF FABRICATED MATERIALS USED ON THE

POLES AND NUMBERING WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS AND EARTHING.

9926000033 DISMENTALLING OF 8 MTR PSC POLE WITH CREDITING OF FABRICATION AT No.

33 STORE &STACKING OF POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

9926000034 DISMENTALLING OF 10 MTR PSC POLE WITH CREDITING OF FABRICATION No.

34 AT STORE & STACKING OF POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

9926000035 DISMENTALLING OF TRANSFORMER CENTRE (8 MTR PSC POLE) (WITH No.

TRANSFORMER) WITH CREDITING OF FABRICATION & TRANSFORMER AT

35 STORE & STACKING OF POLE SAFELY ON ROADSIDE OR CREDITING TO

DEPARTMENTAL STORE

9926000036 DISMENTALLING OF TRANSFORMER CENTRE (8 MTR PSC POLE) (WITHOUT No.

36 TRANSFORMER) WITH CREDITING OF FABRICATION AT STORE & STACKING

OFPOLE SAFELY ON ROAD SIDE ORCREDITING TO DEPARTMENTAL STORE

9926000037 STRINGING OF LT ABC OF 1*35 SQ MM + 1*25 SQ MM INCLUDING FIITING OF KM

ALL ACESSORIES I.E. SPECIAL DESIGN SUSPENSION / TENSION CLAMP,

FIXING OF CROSS ARM, LT SHACKLE INSULATOR ETC. FOR FIXING OF

MESSENGER WIRE AND TO PROVIDE SERVICE CONNECTION ON AERIAL

BUNCH CABLE BY INSULATED PIERCE-ING CONNECTORS THROUGH

37 SERVICE CONNECTION BOX COMPLETE AS REQUIRED & DIRECTED BY

ENGINEER IN CHARGE.

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

9926000038 STRINGING OF LT ABC OF 3*50 SQ MM +1*25 SQ MM+1*35 SQ MM KM

INCLUDING FITTING OF ALL ACESSARIES I.E. SPECIAL DESIGN

SUSPENSION / TENSION CLAMP, FIXING OF CROSS ARM, LT SHACKLE

INSULATOR ETC. FOR FIXING OF MESSENGER WIRE AND TO PROVIDE

38 SERVICE CONNECTION ON AERIAL BUNCH CABLE BY INSULATED PIERCE-

ING CONNECTORS THROUGH SERVICE CONNECTION BOX COMPLETE AS

REQUIRED & DIRECTED BY ENGINEER IN CHARGE.

9926000039 STRINGING OF 11KV ABC OF 3*95 SQ MM +80 SQ MM INCLUDING FITTING KM

OF ALL ACESSARIES I.E. SPECIAL DESIGNSUSPENSION / TENSION CLAMP,

FIXING OF CROSS ARM, BINDING TO PIN INSULATOR,PREPARING

39 SHACKLEPOINT,JUMPERS ETC. AS REQUIRED &DIRECTED BY ENGINEER IN

9926000040 STRINGING OF 22 KV ABC OF 3*70 SQ MM +95 SQ MM INCLUDING FITTING KM

OF ALL ACESSARIES I.E. SPECIAL DESIGNSUSPENSION / TENSION CLAMP,

FIXING OFCROSS ARM, BINDING TO PIN INSULATOR,PREPARING

40 SHACKLEPOINT,JUMPERS ETC. AS REQUIRED AND DIRECTED BY

ENGINEER IN CHARGE

9926000041 STRINGING OF LT ABC OF 2*50 SQ MM +1*25 SQ MM+ 35 SQ MM INCLUDING KM

FITTING OF ALL ACESSORIES I.E. SPECIAL DESIGN SUSPENSION / TENSION

CLAMP, FIXING OF CROSS ARM, LT SHACKLE INSULATOR ETC. FOR FIXING

OF MESSENGER WIRE AND TO PROVIDE SERVICE CONNECTION ON AERIAL

41 BUNCH CABLE BY INSULATED PIERCE-ING CONNECTORS THROUGH

SERVICE CONNECTION BOX COMPLETE AS REQUIRED & DIRECTED BY

ENGINEER IN CHARGE.

9926000042 DISMENTALING OF RSJ (9/11 METER) POLE AND CREDITING THE OLD Nos

42 MATERIAL TO STORE

9926000043 DISMENTALING TRANSFORMER CENTER ON IO MTR,270KG PSC POLE Nos

WITHOUT TRANSFORMER WITH CREDITING OF FABRICATION AT STORE

43 AND STACKING OF POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

9926000044 DISMENTALING OF TRANSFORMERCENTER ON IOMTR,270KG PSC Nos

POLE(WITH TRANSFORMER) WITH CREDITING OF FABRICATION AT STORE

44 AND STACKINGOF POLE SAFELY ON ROAD SIDE ORCREDITING TO

DEPARTMENTAL STORE

9926000045 DISMENTLING OF 11KV ABC OF 3*95 SQ MM +80 SQ MM AND CREDITING KM

45 FITTINGOF ALL ACESSARIES AND FABRICATION TO DEPARTMENTAL

9926000046 DISMENTLING OF 22 KV ABC OF 3*70 SQ MM +95 SQ MM AND CREDITING KM

46 FITTINGOF ALL ACESSARIES AND FABRICATION TO DEPARTMENTAL

9926000047 DISMENTALING OF LT ABC OF 1*35 SQ MM + 1*25 SQ MM AND CREDITING KM

47 FITTING OF ALL ACESSARIES TO DEPARTMENTAL STORE.

9926000048 DISMENTALING OF LT ABC OF 3*50 SQ MM +1*25 SQ MM+1*35 SQ MM AND KM

48 CREDITING FITTING OF ALL ACESSARIES TO DEPARTMENTAL STORE.

9926000049 DISMENTALING OF LT ABC OF 2*50 SQ MM +1*25 SQ MM+ 1*35 SQ MM AND KM

49 CREDITING FITTING OF ALL ACESSARIES TO DEPARTMENTAL STORE.

9926000050 RESTRINGING OF ALL TYPE OF CONDUCTOR (EXCEPT DOG CONDUCTOR) ONE

50 FOR 11/22KV & LT LINES INCLUDING FIXING OF INSULATORS, BINDING COND

JUMPERING ETC. PER KM

9926000051 RESTRINGING OF DOG CONDUCTOR FOR 11/22KV HT LINES INCLUDING , ONE

51 BINDING JUMPERING ETC. COND

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

9926000052 LABOUR CHARGE FOR THE INSTALLATION OF NEW DTR METER. (METER NO.

52 WILL BE PROVIDED BY DGVCL

9926000053 LABOUR CHARGE FOR THE REPLACEMENT OF DTR METER AND OLD NO.

53 METER SHOULD BE CREDITED TO SDN STORE. (METERWILL BE PROVIDED

9926000054 LABOUR CHARGE FOR PROVIDING CT COIL FOR DTR METER CONNECTION. PER

54 (CT COILWILL BE PROVIDED BY DGVCL CT

9926000055 LABOUR CHARGE FOR REPLACEMENT OF CT COIL FOR DTR METER PER

55 CONNECTION AND OLD CT SHOULD BE CREDITED TO SDN STORE. (CT COIL CT

WILL BE PROVIDED BY DGVCL

9926000056 LABOUR CHARGE FOR FIXING OF MMB FORDTR METER (MMB WILL BE NO.

56 PROVIDED BY DGVCL

9926000057 LABOUR CHARGE FOR REPLACEMENT OF DTR METER BOX. NO.

57 (METER WILL BEPROVIDED BY DGVCL

9926000058 PROVIDING / REPLACEMENT OF 1.5 SQ MM 10 CORE COPPER CABLE 3.5 NO.

58 METER (CABLETO BE PROVIDED BY AGENCY

9926000059 LABOUR CHARGE FORPROVIDING/RECONNECTION OF PER

59 TERMINALCONNECTION WITH PROPER SIZE OF LUGS. LUGS COST IS TERMIN

BORNE BY AGENCY ATION

9926000060 LABOUR CHARGE FOR THE SPOT READINGOF DTR METER WITH DETAIL PER

SURVEY OF DEFECT IF ANY. A DULY SIGN COPY BY SURVEYOR PERSON DTR

OF AGENCY IN PROFORMA REPORT SHOULD BE SUBMITTEDTO SDN ONLY

IF ALLPARAMETER OF VOLTAGE, CURRENT & LOAD AS SHOWN IN PER-

FORMA IS FILLED) AS PER THE INSTRUCTION OF ENGINEER IN-CHARGE.

9926000061 LABOUR CHARGE FOR THE SPOT READINGOF DTR METER WITH DETAIL PER

SURVEY OF DEFECT IF ANY. A DULY SIGN COPY BY SURVEYOR PERSON DTR

OF AGENCY IN PROFORMA REPORT SHOULD BE SUBMITTED TO SDN

OFFICE. (DULY FILL PER-FORMA IN FAULT CONDITION IN WHICH

READINGPARAMETER IS NOT SHOWN IN METER

9926000062 INSTALLATION OF DTR METER INCLUDING METER BOX, PROVIDING & NO.

FIXING OF 1.5SQ MM SINGLE STRAND 10 CORE ARMOURED COPPER

62 CABLE (3.5METER), TERMINATION IN METER & COIL BOX,CT/PT COIL

WILLBE PROVIDED BY DGVCL

9926000063 INSTALLATION OF DTR METER INCLUDING METER BOX, TERMINATION IN NO.

63 METER & COIL ETC. (WITHOUT 10 CORE COPPERCABLE) (METER,METER

BOX,CT/PT COILWILL BE PROVIDED BY DGVCL

9926000064 Binding of messanger Conductorat with a distance not more than 0.75 mtr with 6 NO

turns minimum on XLPE Cable with single strand binding wire (including cost of

9926000086 Supply and Installation of 11/22 kV Distribution Transformers HT Terminal protector PER SET

65 (UV Resistance) with using 95/120/150 sq.mm long barrel aluminum lug. (1Set =

Nos i.e. on R, Y, B)

9926000087 Supply & Installation of HT EPR Tap on 11/22 kV Distribution Transformer with PER SET

replacement of bare conductor by HT ABC conductor (DO bottom side to

66 transformer) after removal of semi conductor by HT ABC (6 inch both side). HT

ABC to be supplied by DGVCL. (1Set = 3 Nos i.e. on R, Y, B)

9926000088 Supply, Installation, Testing and Commissioning of Maintenance Free, Ready NO

Capsule, Pipe-In-Cage (Pic) Type, Earth Electrodes for HT Feeder Pole Having

67 2000 mm Electrode Length as per the Tender Specifications and Drawing. (All

Materials Will Be Supplied By Agency)

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

9926000089 Supply, Installation, Testing and Commissioning of Maintenance Free, Ready NO

Capsule, Pipe-In-Cage (Pic) Type, Earth Electrodes for HT Feeder Pole Having

68 3000 mm Electrode Length as per the Tender Specifications And Drawing. (All

Materials Will Be Supplied By Agency)

9926000090 Supply and Installation of 25 X 3 mm GI Strip having hot dip- galvanized-zinc Meter

coating of 80-100 microns without any joints or welding. Both the end of the GI strip

should be connected with GI nut bolts and required fabrication work for giving

69 separate earthing connections to(1) Neutral of the transformer(2) MS structures of

the transformer center (Approximately 25 meter GI strip per transformer centre- as

per requirement and instruction of Engineer in- charge) (All Materials will be

supplied by Agency)

9926000092 Supply and Installation of uPVC standard make Pipe of 1.25" diameter for covering Meter

GI strip with UV protected Cable Ties of 550 X 7.6 mm size to bind with pole

face(Approximately 25 meter uPVC pipe for GI strip covering per transformer centre

-as per requirement and instruction of Engineer in-charge.

9926000093 Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and per TC

71 Drop out fuse to Transformer H.T. including Busbar (12 mm sleev) as per technical

specification. (All Materials will be supplied by Agency)

9926000100 Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and per TC

72 Drop out fuse to Transformer H.T. without Busbar (15 mm sleev) as per technical

specification. (All Materials will be supplied by Agency)

9926000094 Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and per TC

73 Drop out fuse to Transformer H.T. including Busbar(15 mm sleev) as per technical

specification. (All Materials will be supplied by Agency)

9926000101 Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and per TC

74 Drop out fuse to Transformer H.T. without Busbar(15 mm sleev) as per technical

specification. (All Materials will be supplied by Agency)

9926000095 Supply & fixing of Disc type Red Color FRP(Non-flammable) material with Weather NO

resistant, Non-conductive bird guard OD=300 MM, ID=33 MM, Width =1.25 MM,

75 one side cut from ID to OD. (All Materials will be supplied by Agency)

9926000096 Providing and fixing of LT Terminal protectors i.e. Re-useable boot (LT Side 1.1 kV) NO

76 including LT (1.1 kV) insulating taps. All live part at LT side shall be covered with

fixing of LT insulating taps.

77 Nylon Net around Transformer Center

77.1 9926000097 Nylon Net (12 * 15 ft) Per Net

77.2 9926000098 Nylon Dori Per tc

9926000099 Labour charge for fitting Nylon Net (All fabricated material for fitting nylon net shall Per tc

77.3 be provided by DGVCL)

(B)Labour Charges for Maintenance Work

1 9924000001 Cutting of Tree branches surrounding HT/LT line per Tree

Replacement of old jumpers & providing new double jumpers with 8" binding &

2 9924000002 capsuling with PVC pipe etc. No

3 9924000005 Support pole for stay PSC/STP/RSJ No.

4 9924000006 Pin binding of conductor 11/22kv Pin insulator No.

Pin binding of conductor 11/22kv Pin insulator per pole in coastal area with

5 9924000007 cleaninGg . No.

6 9924000008 Pin binding of conductor LT shackle insulator No.

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

7 9924000009 Replacement of one/bothinsulator at strain pole No.

8 9924000010 Replacement of LT shackle insulator at cut point No.

9 9924000011 Re-fixing of V cross Arm No.

10 9924000012 Re placement of V cross Arm No.

11 9924000013 Re-fixing of Top fitting in proper position No.

12 9924000014 Replacement of Top fitting No.

13 9924000015 Replacement of LT cross Arm No.

14 9924000016 Providing DO fuse on DP with carting& jumpering (ONE DO FUSE) No.

Numberings of pole with paint by preparing back ground of one colour and

15 9924000017 have lettering(height 3" * width0.5" using stencil No.

16 9924000018 Fixing of MMB(IPH.) at consumer end No.

17 9924000019 Fixing of MMB(3PH.) at consumer end No.

18 9924000020 Replacement of (Iph.) meter forUrban area No.

19 9924000021 Replacement of (Iph.) meter for Rural area No.

painting consumer no. on MMB (Urban) (with letter size height40mm* width 8mm

painting consumer no. on MMB (Rural) (with letter size height 40mm* width 8mm

22 9924000024 Replacement of deteriorated Single hase Service line No.

23 9924000025 Fixing of new dist. Box with complete wiring includin clamps, nut bolts etc. No.

Repairing of guarding involving reshaping of bearer wire cross lacing binding etc.

25 9924000027 Painting of steel fabricated material of RSJ DO DP structure with paint No.

Painting of steel fabricated material of RSJ pole mounted transformer double pole

26 9924000028 structure with paint No.

27 9924000029 Painting of steel fabricated material of RSJ single pole with paint No.

28 9924000030 painting of steel fabricated material of PSC Single pole (HT line) with paint No.

29 9924000031 painting of steel fabricated material of PSC DO DP double pole with paint No.

painting of steel fabricated material of PSC double pole at pole mounted

30 9924000032 transformer with paint No.

31 9924000033 Providing line separator single phase No.

32 9924000034 Providing line separator three phase No.

Replacement / Providing of stay insulator along with adjustment

33 9924000035 of tension in stay wire No.

Replacement of deteriorated /providing LT dist. Box with new up to 100KVA

34 9924000036 capacity & crediting it to store. No.

Replacement of deteriorated /providing LT dist. Box with new above 100KVA

35 9924000037 capacity & crediting it to store. No.

36 9924000038 Adjustment of tension in stay wire No.

37 9924000039 Refitting of LA No.

38 9924000040 Converting pin point to Shackle point including dismantling & restringing etc. location

39 9924000041 replacement of 11KV Pin insulator with providin new double in binding No.

replacement of 22KV Pin insulator by new 11 kv pin insulator with spares & providin

40 9924000042 new double in binding No.

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

41 9924000043 Providing 11 kv double disc insulators with binding & restringing No.

42 9924000045 Replacement of existing conductor (all size) with new double in binding Cond/KM

43 9924000046 Plumbing of psc Pole with straightening at pin point No.

44 9924000047 Plumbing of psc Pole with straightening at tension point No.

Plumbing of tilted DP structure (PSC/RSJ/STP) with refilling of stone Murrum etc.

Providing new 11 kv AB [GO switch with fabrication and insulated colour code

46 9924000049 jumper binding lugs etc. Set

Replacement of old 11 kv AB /GO switch with providing new insulated jumper,

47 9924000051 binding, lugs etc. Set

Providing cage type loop guard in vertical LT line with using PVC reel insulators etc.

48 9924000052 per pole

Labour charges for replacement /providing of MMB & service with all

49 9924000053 accessories for three phase connection No.

Labour charges for replacement /providing of MMB & service with all accessories

50 9924000054 for connection No.

Dismantling of existing Dist. X'mer center (RSJ/STP POLE) 25/63/100/200 KVA

51 9924000055 with all fabrication & crediting the old material to store. No.

52 9924000056 Disconnection from LT pole 1 phase No.

53 9924000057 Reconnection from LT pole 1 phase (payment after receipt of R/C charges) No.

54 9924000058 Disconnection from LT pole 3 phase No.

55 9924000059 Reconnection from LT pole 3 phase (payment after receipt of R/C chagr es No.

Dismantling & removing of service line from pole & crediting to S/dn (1 phase)

Dismantling & removing of service line from pole & crediting to S/dn (3h phase )

58 9924000062 Reconnection of service line complete with PVC cable(1 ph) No.

59 9924000063 Reconnection of service line complete with PVC cable(3 ph) No.

Providing spiral type earthing by connecting earth terminal with earth terminal of

meter box with G.I. SWG no 8 up to 1.5meters (total weight approximately 2.2kg-20

meter in length) with salt and coal 10kg each, including pvc rigid pipe 20mm dia

(1.5mtr length) to cover exposed part of G.I. wire , providing and fixing of single

core 1.5 sq mm single strand copper insulated cable with cable nail clip to be

connected with connector to G.I. wire at consumer end as per drawing DGVCL

cons. earth. Earth resistance should be less than 2 ohms(All materials supplied by

Providing and fixing of single core 1.5 sq mm single strand copper insulated cable

with cable nail clip for spiral type earthing at consumer end. The end of G.I. no 8 is

to be connected by connector with copper cable of which other end shall be

61 9924000070 connected to the earth terminal of meter box. This item shall be used in location per meter

where there is more distance between earth terminal and earthing terminal of

meter. All materials supplied by contractor).

(C) Fabrication from Raw Materials Of Mild Steel

Fabrication of Anchor Rod from 16 SQ.mm MS Round bar & 65 mm x 65 mm x

62 9910000049 mm M.S. angle as per approved drawing and requirement of the company. No.

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

Fabrication of Anchor Rod from 16 SQ.mm MS Round bar & 50 mm x 50 mm x

63 9910000050 mm M.S. angle as per approved drawing and requirement of the company. No.

Fabrication of Eye Bolt from 16 SQ.mm MS Round bar with supplying of 2 (two)

64 9910000015 nuts of suitable size as per approved drawing and requirement of the company. No.

Fabrication of Turn Buckle from 16 SQ.mm MS Round bar & 65 mm x 65 mm x

65 9910000028 mm mm M.S. angle as per approved drawing and requirement of the company. No.

Fabrication of Turn Buckle from 16 SQ.mm MS Round bar & 50 mm x 50 mm x

66 9910000016 mm M.S. angle as per approved drawing and requirement of the company. No.

Fabrication of 11' (feet) long Top/Bottom/D.O. angle from 65 mm x 65 mm x 6 mm

67 9910000030 M.S. angle as per approved drawing and requirement of the company. No.

Fabrication of 9' (feet) long Top/Bottom/D.O. angle from 65 mm x 65 mm x 6 mm

68 9910000031 M.S. angle as per approved drawing and requirement of the company. No.

Fabrication of 4'6" (feet) long Tapping / bracing angle from 65 mm x 65 mm x 6 M.S.

69 9910000003 angle as per approved drawing and requirement of the company. No.

Fabrication of 2'3" (feet) long bracing/ support angle from 65 mm x 65 mm x 6mm

70 9910000039 M.S. angle as per approved drawing and requirement of the company. No.

Fabrication of 11KV HT 'V' Cross Arm from 65 mm x 65 mm x 6 mm M.S. angle as

71 9910000021 per approved drawing and requirement of the company. No.

Fabrication of 11KV HT Top fitting from 65 mm x 65 mm x 6 mm M.S. angle and

72 9910000022 50mm x 6 mm M.S. flat as per approved drawing and requirement of the company. No.

Fabrication of 22KV HT Top fitting from 65 mm x 65 mm x 6 mm M.S. angle and

73 9910000055 50mm x 6 mm M.S. flat as per approved drawing and requirement of the company. No.

Fabrication of 22KV HT 'V' Cross Arm from 65 mm x 65 mm x 6 mm M.S. angle as

74 9910000037 per approved drawing and requirement of the company. No.

Fabrication of Guy Clamp pair suitable for PSC pole from 50mm x 6 mm M.S. flat as

75 9910000041 per approved drawing and requirement of the company. PAIR

Fabrication of 'U' Clamp from 50mm x 6 mm M.S. flat as per approved drawing and

76 9910000024 requirement of the company. No.

Fabrication of 'C' clamp suitable for PSC pole from 50mm x 6 mm M.S. flat as per

77 9910000043 approved drawing and requirement of the company. No.

Fabrication of ‘C’ clamp suitable for RSJ GIRDER pole from 50mm x 6 mm M.S. flat

78 9910000044 as per approved drawing and requirement of the company. No.

Fabrication of Three hole patti from 50mm x 6 mm M.S. flat as per approved

79 9910000056 drawing and requirement of the company. No.

Fabrication of 11' (feet) long Top/Bottom channel from 100 mm x 50 mm x 5 mm

80 9910000061 M.S. channel as per approved drawing and requirement of the company. No.

Fabrication of 9' (feet) long Top/Bottom channel from 100 mm x 50 mm x 5 mm M.S.

81 9910000060 channel as per approved drawing and requirement of the company. No.

Fabrication of 11'(feet) long angle bracing from 50 mm x 50 mm x 6 mm M.S. angle

82 9910000035 as per approved drawing and requirement of the company. No.

Fabrication of 9'(feet) long angle bracing from 50 mm x 50 mm x 6 mm M.S. angle

83 9910000034 as per approved drawing and requirement of the company. No.

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

Fabrication of 11' (feet) long channel welded from assorted length of scrap channel

84 9910000062 as per approved and requirement of the company No.

Fabrication of 9' (feet) long channel welded from assorted length of scrap channel

85 9910000063 as per approved and requirement of the company No.

Fabrication of Guy Clamp pair suitable for 10 mtr PSC pole from 50mm x 6 mm

86 9910000072 M.S. flat as per approved drawing and requirement of the company. PAIR

Fabrication of Guy Clamp pair suitable for 9/11mtr RSJ GIRDER pole from 50mm x

87 9910000073 6 mm M.S. flat as per approved drawing and requirement of the company. PAIR

Fabrication of 5' (feet) long Tapping angle from 65 mm x 65 mm x 6 mm M.S. angle

88 9910000066 as per approved drawing and requirement of the company. No.

Fabrication of H.T. Ext'n suitable for 22KV system from 65 x 65 x 6 mm M.S. angle

89 9910000067 as per approved drawing and requirement of the company. No.

Fabrication of H.T. Ext'n suitable for 11KV system from 65 x 65 x 6 mm M.S. angle

90 9910000068 as per approved drawing and requirement of the company. No.

Fabrication of 750 mm long Channel for HT AB conductor from 100mm x 50mm x

91 9910000069 5mm M.S. Channel as per approved drawing and requirement of the company. No.

92 9910000070 Fabrication of 22KV HT "V" Cross Arm from 100mm x 50mm x 5mm M.S. Channel No.

as per approved drawing and requirement of the company.

(D) REPLACEMENT OF BARE CONDUCTOR BY HT / LT AERIAL BUNCH CONDUCTOR

Stringing of LT ABC of 1*35 SQ MM + 1*25 SQ MM including fitting of all

acessaries i.e. special design suspension / tension clamp, fixing of cross arm, LT

shackle insulator etc. for fixing of messenger wire and inclusive of dismantling

charge of existing bare conductor and crediting in to store & dismentaling of service

line from LT bare conductor and to provide service connection on Aerial Bunch

Cable by insulated pierceing connectors through service connection box complete

as required & directed by Engineer in Charge.

Stringing of LT ABC of 3*50 SQ MM +1*25 SQ MM+1*35 SQ MM including fitting of

all acessaries i.e. special design suspension / tension clamp, fixing of cross arm, LT

shackle insulator etc. for fixing of messenger wire and inclusive of dismantling

charge of existing bare conductor and crediting in to store & dismentaling of service

line from LT bare conductor and to provide service connection on Aerial Bunch

Cable by insulated pierceing connectors through service connection box complete

as required & directed by Engineer in Charge.

Stringing of 11KV ABC of 3*95 SQ MM +80 SQ MM including fitting of all

acessaries i.e. special design suspension / tension clamp, fixing of cross arm,

binding to pin insulator,preparing shackle point,jumpers etc. and inclusive of

dismantling charge of existing bare conductor and crediting in to store complete as

required & directed by Engineer in Charge

Stringing of 22 KV ABC OF 3*70 SQ MM +95 SQ MM including fitting of all

acessaries i.e. special design suspension / tension clamp, fixing of cross arm,

binding to pin insulator,preparing shackle point,jumpers etc. and inclusive of

dismantling charge of existing bare conductor and crediting in to store complete as

required & directed by Engineer in Charge

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

Stringing of LT ABC of 2*50 SQ MM +1*25 SQ MM+ 35 SQ MM including fitting of

all acessaries i.e. special design suspension / tension clamp, fixing of cross arm, LT

shackle insulator etc. for fixing of messenger wire and inclusive of dismantling

charge of existing bare conductor and crediting in to store & dismentaling of service

line from LT bare conductor and to provide service connection on Aerial Bunch

Cable by insulated pierceing connectors through service connection box complete

as required & directed by Engineer in Charge.

(E)LABOUR RATE FOR UNDERGROUND CABLE WORK FOR FY 2024-25 (WITHOUT GST)

Sr. Item Code Description

Labour charge for excavation of cable trench of 400mm width x 1200mm depth, in

any type of soil for laying of cable of size up to 240 mm2 (For additional cable

1 9925000001 mm additional width shall be considered i.e. half trench length is to be considered Meter

Labour charge for excavation of cable trench of 600mm width x 1200mm depth, in

any type of soil for laying of cable of size up to 240 mm2 (For additional cable

2 9925000002 mm additional width shall be considered i.e. half trench length is to be considered Meter

Labour charge for excavation of cable trench of 400mm width x 1500mm depth, in

any type of soil for laying of cable of size up to 240 mm2 (For additional cable

3 9925000003 mm additional width shall be considered i.e. half trench leng th is to be considered Meter

Labour charge for laying of 11kV / 22 kV XLPE Cable of size up to 240 mm2 &

preparation of sand layer 100mm thick, in the cable trench & covering the cable

with 150 mm dia (Outer), thickness 25 mm, 1.0 meter long RCC half round muffs

and providing and fixing of 4inch width yellow colour polyethylene tape with

printing"CAUTION ELECTRIC CABLE BELOW' at 0.75 m depth from ground

4 9925000004 surface after laying cable in trench. This will provide indication that electric cable is Meter

passing underground so as to protect cable from mechanical injuries, refilling the

same, as per Instruction of E gineer in Charge (EIC) .

Labour charge for horizontal drilling using Auger machine without damage to

surface road at max 2.0 mtrs depth & putting of 6.11 kg/cm2 , class-4,Green color,

110mm 0.D. 8.5mm thickness H.D.P.E. pipe confirms to IS 4984-1987(3rd revision)

and BIS certification and laying of 11KV/22KV XLPE cable of size up to 240 mm2 in

HDPE pipe, as per Site Condition (excluding cost of pipe). The detail map obtained

from HDD machine and excel sheet hard and soft copy) indicating the respective

5 9925000005 depth and distance from adjacent landmark for each segment for HDD is must Meter

require to be submitted. HDD to be carried out at depth 1.5 mtrs to 2.0 mtrs as per

site conditions and as er instruction of EIC.

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

Labour charge for horizontal drilling manually without damage to surface road at

max 2.0 mtrs depth & putting of 6.11 kg/cm2 , class-4,Green color, 110mm O.D.

8.5mm thickness H.D.P.E. pipe confirms to IS 4984-1987(3rd revision) and BIS

certification and laying of 11KV/22KV XLPE cable of size up to 240 mm2 size, as

per Site Condition (excluding cost of pipe). The detail map and excel sheet (hard

6 9925000006 and soft copy) indicating the respective depth and distance from adjacent landmark Meter

for each segment of cable to be submitted. Drilling to be carried out at depth

Minimum 1.2 mtrs to 2.0 mtrs as per site conditions as per instruction of EIC.

Supply of 6.11kg/cm2 , class-4,Green color, 110mm O.D. , 8.5 mm thickness

7 9925000007 H.D.P.E. pipe confirms to IS 4984 and BIS certification for laying of underground Meter

11KV/ 22KV XLPE cable up to 240 mm 2 size.

Labour work for RCC concreting on disputed location and repairing of damage

8 9925000008 portion of road crossing for the work carried out for roads crossing as well as CMT

concreting & muffing of poles including all materials

Providing & fixing concrete stone route marker of 300 mm width x 150 mm thick x

650 mm height embedded in earth at least 300 mm below & 350 mm above ground

level respectively at distance approx. 50 meters along the length of cable. The RCC

concreting (1:2:4)(all necessary materials will be in bidder's scope) of route marker

is to be carried out 300 mm width x 150 mm thick x 300 mm below ground level as

per instruction of EIC. The route marker should be with name of company with

9 9925000009 approved yellow colour-DGVCL. The distance from marker to cable and cable No

depth with feeder name etc., marked with arrow sign is to be painted on it. The

route marker is to be fixed at location near to any fixed permanent location (not

necessary to fix exact on top of cable) as per instruction of EIC.

Erection of D.P. (double pole) structure using 9 / 11 Mtr. RSJ pole with cable

connection arrangement along with fitting of necessary fabrication for 11KV cable

10 9925000010 including excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of No

concreting & muffing of poles)

Erection of Single pole structure using 9 / 11 Mtr RSJ pole with cable connection

arrangement along with fitting of necessary fabrication for 11KV/22 KV cable

11 9925000011 including excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of No

concreting & muffing of poles

Erection of D.P. (double pole) structure using 8.0 Mtr. PSC pole with cable

connection arrangement along with fitting of necessary fabrication for 11KV cable

12 9925000012 including excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of No

concreting & muffing of poles

Erection of Single pole structure using 8.0 Mtr PSC pole with cable connection

arrangement along with fitting of necessary fabrication for 11KV/22 KV cable

13 9925000013 including excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of No.

concreting& muffing of poles

Labour charge for erecting of 11kV / 22 kV XLPE cable of size up to 240 mm 2 on

14 9925000014 DP Structure with fixing of 02 Nos polymer cleats on top and middle part. Polymer Meter

cleats, nut bolts etc. fixing material to be provided by contractor.

Providing & fixing of 6.11kg/cm2 , class4,Green color, 110mm O.D. 8.5mm

thickness H.D.P.E. pipe confirms to IS 4984 and BIS certification on the erected DP

structure for the mechanical protection of cable by inserting the cable inside HDPE

pipe. The HDPE pipe shall be erected in such a way that 300mm shall be below the

15 9925000015 ground level and the rest 2700 mm shall be supported on the DP Structure with 01 perJob

No Polymer cleat. All materials including polymer cleat and Nut bolt to be provided

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

Providing and fixing of pipe type earthing from 80 mm dia class-B GI pipe with pit to

be filled with salt & coke and construction of chamber as per DGVCL Drg. No. dg

/100 for DP and cable. The earthing pit should be joined with cable by G.I. strip of

size 1" width & 2 mm thick. All material GI pipe, Coke Salt etc will be supplied by

Supply & fixing of heat shrink type end terminations (outdoor) for up to 11kV 3C x

17 9925000017 185 mm2 size XLPE cable as per DGVCL technical s ecification No

Supply & fixing of heat & shrinkable end terminations (outdoor) for up to 22 kV 3C x

18 9925000018 185 mm 2 size XLPE cable ( as per DGVCL technical specification) No

Supply & fixing of heat shrinkable type end terminations (indoor) for up to 11kV 3C

19 9925000019 x 185 mm 2 size XLPE cable as per DGVCL technical specification No

Supply & fixing of heat & shrinkable end terminations (indoor) for up to 22 kV 3C x

20 9925000020 185 mm 2 size XLPE cable as per DGVCL technical specification No

Supply & fixing of heat shrinkable straight through joint for up to 11kV 3C x 185 mm

21 9925000021 2 size XLPE cables as per DGVCL technical specification. No

Supply & fixing of heat shrinkable straight through joint type for up to 22kV 3C x

22 9925000022 185 mm 2 size XLPE cable as per DGVCL technical specification No

Labour charge for excavation of 2100mm long x 1200mm wide x 1200 mm deep

joint pits for installation of 11kV / 22kV Straight through joints as per instruction of

engineer-in-charge & covering the cable with 150 mm dia (Outer), thickness

mm, 1.0 meter long RCC half round muffs & refilling same as per instruction of EIC

Providing and fixing of insulating bus bar, made from 11KV/22KV XLPE cable after

removal of semi conducting layer and applying of PVC heat shrinkable antitracking

core insulating tubing (1.1KV), on both end terminal using Aluminium long barrel

heavy duty up to 240 sq mm lugs, Aluminium bus connector. Taping with PGclamp

for bus conductor as per drawing and as per instruction of EIC. The Allurninium lugs

and PG clamp shall be covered with 11KV/22KV HT insulating tapes.(11KV/22KV

XLPE cable will be in scope of DGVCL while all other materials will be in bidder's

Testing of cable at various points and commissioning the feeder as per instruction

25 9925000025 of engineer-in-charge.Test result shall be submitted by contractor with bill. No

Preparation and submission of 6 (six) copies, of complete layout drawings with GIS

26 9925000026 mapping as per actual cable routing showing road crossing, HDPE pipe sleeving, Set

jointing locations, markers etc.

Providing and fixing of Sign Board at junction point Made out of 2 mm aluminium

sheet size 750x300 mm (2.5 x 1 ft) rectangle, as per design, pretreated with

phosphate process and acid etching coated with one coat of epoxy primer and two

coats of best quality paints, reflectorized with Hi Intensity retro — reflective sheeting

as per the latest and frame fabricated from suitable size iron angle. The Sign Board

is to be fixed on the base prepared from channel and bracing angles which is

27 9925000027 grouted by means of cement concreting of 1:2:4 for size of 300 mm dia x 800 mm No

height (500 mm to be grouted in ground). The details to be displayed on sign board

will be given by InchargeEngineer. (a) Hi intensity Micro prismatic Grade

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

Providing and fixing of Sign Board (Danger Board) on Distribution Transformer

Centers Made out of 2mm aluminium sheet size 300x300mm (1X1 ft) as per design,

pre treated with phosphate process and acid etching coated with one coat of epoxy

primer and two coats of best quality paints, reflectorized with Hi-Intensity

retroreflective sheeting as per the latest and frame fabricated from suitable size iron

angle. The Sign Board (Danger Board is to be fixed at the location as per instruction

of In-charge Engineer. (a) Hi intensity Micro prismatic Grade

Providing & fixing of aluminium tag of size 250 mm (L) x 75 mm (W) from 3 mm

aluminium sheet along with 1.0 mm dia aluminium binding wire for fixing of

aluminium tag near end termination joint at DP structure for identifying the cable.

29 9925000029 The details of feeder i.e. 11 / 22 KV with feeder name should be punched on the No

tag by letter punch of size 16 mm as per instruction of In-charge Engineer.

Supply & fixing of heat shrink type end terminations (outdoor) for 11kV 3C x

30 9925000030 mm2 size XLPE cable as per DGVCL technical specification. Nos

Supply & fixing of heat & shrinkable end terminations (outdoor) for 22 kV 3C x

31 9925000031 mm2 size XLPE cable as per DGVCL technical specification Nos

Supply & fixing of heat shrink type end terminations (indoor) for 11kV 3C x

32 9925000032 mm2 size XLPE cable as per DGVCL technical specification Nos

Supply & fixing of heat & shrinkable end terminations (indoor) for 22 kV 3C x

33 9925000033 mm2 size XLPE cable as per DGVCL technical specification Nos

Supply & fixing of heat shrinkable straight through joint for 11kV 3C x 240 mm2 size

34 9925000034 XLPE cables as per DGVCL technical s ecification. Nos

Supply & fixing of heat shrinkable straight through joint type for 22kV 3C x

35 9925000035 mm2 size XLPE cable as per DGVCL technical s ecification Nos

Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRL

36 9925000038 type3 Way RMU including Two numbers of earthings as per Drawing (material is in Nos

bidder's scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRLL

37 9925000039 type4 Way RMU including Two numbers of earthings as per Drawing (material is in Nos

bidder's scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRL

38 9925000040 type-3 Way, RMU including Two numbers of earthings as per Drawing (material is Nos

in bidder's scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRLL

39 9925000041 type-4 Way, RMU including Two numbers of earthings as per Drawing (material is Nos

in bidder's scope) and as per DGVCL Technical specification.

Construction of plinth for 11KV, RRL type- 3 Way( i.e Two numbers of Isolator &

One number of Breaker) Ring Main Unit as per DGVCL's technical specification

40 9925000042 mentioned in drawing no: Drg. 11kv-01. All required material will be supplied by Nos

Construction of plinth for 11KV, RRLL type4 Way (i.e Two numbers of Isolator &

Two number of Breaker)Ring Main Unit as per DGVCL's technical specification

41 9925000043 mentioned in drawing no:Drg. 11kv-02.AlI required material will be supplied by Nos

Construction of plinth for 22KV, RRL type- 3 Way (i.e Two numbers of Isolator &

One number of Breaker) Ring Main Unit as per DGVCL's technical specification

42 9925000044 mentioned in drawing no: Drg. 22kv-01. All required material will be supplied by Nos

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

Construction of plinth for 22KV, RRLL type4 Way (i.e Two numbers of Isolator &

Two number of Breaker)Ring Main Unit as per DGVCL's technical specification

43 9925000045 mentioned in drawing no:Drg. 22kv-02.All required material will be supplied by Nos

Modifications e.g. Providing and fixing ofTerminal protectors i.e. Re-use able boot

(HT Side 11/22KV, LT Side 1.1KV) including 11/22 KV insulating taps and L.T.(I.I

KV) insulating taps ,Busbar, Tapping from Bus Bar (11/22 KV XLPE cable) through

P.G. Clamp for H.T. Jumper to D.O. Fuse to bushings of Transformer Center,

providing & Fixing of jumper and providing & fixing of Heat Shrinkable Anti Tracking

CoreInsulating Tubing (Insulation Level 11/22 KV) in H.T. jumper , Clamping

arrangement of cable support frame on both side of existing Over Head type

Distribution Transformer to utilize in Under Ground cable network as per drawing &

as per instruction of Engineer incharge. All live parts i.e. PGClamp, connections of

D.O.fuses, HT bushings etc . shall be covered with fixing of 11/22 KV HT insulating

tapes. ( 11/22 KV XLPE cable will be in scope of DGVCL while all other materials

will be in bidder's scope )

Laying of any size of 11/ 22 KV XLPE /PILCCable in readymade trench or in open per cable

46 9925000060 Labour charges for lying of O/H XLPE cable pole to pole KM

Supply of 150 mm dia (Inner), thickness 25 mm, 1.0 meter long RCC half round

TOTAL ESTIMATE- TWENTY FIVE LAKHS ONLY

Note :- All Rates are Excluding of GST.

Executive Engineer (O&M),

D.G.V.C.L.,Vapi ind. Division.

1.DGVCL will provide key material like M.S. materials,ABC/Bare conductors, PSC/RSJ Poles, Insulators,Fabricated materials

etc. to the contractor.

2.All fabricated items shall be fabricated as per DGVCL approved drawing and by welding rods confirming to the relevent ISI

specification and as directed by engineer incharge.

3.Necessary electricity connection for fabrication items shall be provided by DGVCL on payment of required charge for

connection & electricity bill of the same shall be paid by the agency.

4.All the rates are inclusive of PF & Exclusive of GST applicable time to time.

5.All steel material are to be painted as below:

(a) Scrubbing of rusted surface properly before applying the paints on to the RSJ poles & steel fabricated materials of

RSJ/PSC poles is must required.

(b) Two coats of approved ISI mark red oxide (primer) is to be properly painted for the RSJ/PSC poles & steel fabricated

materials of RSJ/PSC poles.

(c) Two coats of approved ISI mark silver paint (i.e. triple mangoes or equivalent quality silver paint) is to be properly painted

on to the RSJ poles & steel fabricated materials of RSJ/PSC .

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0634/08/2026 Approved Date: 24-08-2026 04:11

File No: DGVCLDVPI/tender/e-file/4448/2026/2706/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI