ADDN/ALTN OF BLDG NO P-58 (TECHNICAL BLOCK), PROV OF HARD STANDING AND PAVER BLOCKS FOR BLDG NO. P-59 P-198 P-60 P-195 P-09 P-74 P-126 AND FIRE POINTS INSIDE TECHNICAL AREA AT NAD ALWAYE AND PROV OF BIRD PROOF NET AT WED(K) WAREHOUSE AREA (BLDG NO P-

Amount

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated etc) sheets in roof coverings all as specified and directed.

Dismantling of rain water pipe including fittings in any position all as specified and directed.

Dismantling of eaves board fixed in any position with nails all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for wind tie all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar all as specified and directed.

Dismantling of ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets all as specified and directed.

Dismantling of timber scantling 40 sq cm and over in section, in any position all as specified and directed.

Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed.

M&L 25mm thick cement concrete type B1 1:2:4 (20mm graded aggregate) as in floor all as specified and directed.

M&L hardcore of guage exc 63mm but n exc 100mm, deposited, spread and levelled in layers n exc. 15Cm thick watered and rolled/rammed to a true surface all as specified and directed.

M&L Cement concrete 75mm thick type C- 2, 1:3:6(40mm graded aggregate) as in plinth protection all as specified and directed.

M&L Providing precast cement concrete solid building blocks type C1 1:3:6 (20 mm graded aggregate) set in Cement Mortar 1:4or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar, complete, in walls all as specified and directed.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:4 finished even and smooth without using extra cement all as specified and directed.

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:6 finished even and smooth without using extra cement all as specified and directed.

M&L Preparation of new or previously untreated surface Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coat of Oil bound distemper on wall surface all as specified and directed.

M&L Preparation of old surface and providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying one coat of Oil bound distemper on wall surface all as specified and directed.

M&LPreparation of new or previously untreated plastered surface and applying two coat of cement base paint over a coat of primer all as specified and directed.

M&L Preparation of old plastered surface and applying one coat of cement base paint all as specified and directed.

S&F Light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to Match over 10mm thick screed bed in cement mortar 1:4 all as specified and directed.

S&F Non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exc 0.18sqm but not exc 0.38sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick screed bed in CM 1:4 all as specified and directed.

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L Pre-painted galvalume aluminium zinc coating GI based pain steel sheet 0.50mm thick of any colour having tensile strenght of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L Roof tiles, Mangalore pattern, interlocking at side joints, laid dry all as specified and directed.

M&L Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 all as specified and directed.

S&F Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick screed bed in CM 1:4 all as specified and directed.

S&F Glazed ceramic coloured tiles in vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 all as specified and directed.

Hacking out old broken glass (any thickness, size quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified and directed.

S&F in repair sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square n.exc 0.5 sq.m in each pane all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

Taking down shutters of any description n.exc 1 sqm each all as specified and directed.

Same as per item No 31 above but exc 1 sqm and n.exc 2 sq.m each all as specified and directed.

Resecuring or easing & adjusting without taking down shutters n.exc 1 sqm all as specified and directed.

Same as per item No 33 above but exc 1 sqm and n.exc 2 sq.m each all as specified and directed.

S&F Glazed and skeleton shutters 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of Framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters As specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat all as specified and directed.

S&F II class Hard wood Plain framed, panelled shutter 35mm thick(two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part 1), kiln seasoned and chemically pressure treated all as specified and directed.

S&F Aluminium anodised, barrel tower bolts 100mm thick of ex-truded section and fixed all as specified and directed.

S&F Aluminium anodised, barrel tower bolts 150mm thick of ex-truded section and fixed all as specified and directed.

S&F in repair Aluminium anodised, barrel tower bolts 100mm thick of ex-truded section and fixed all as specified and directed.

S&F in repair Aluminium anodised, barrel tower bolts 150mm thick of ex- truded section and fixed all as specified and directed.

S&F Butt hinges 75 mm thick, meduim weight, cold rolled mild steel, and fixed all as specified and directed.

S&F Butt hinges 100 mm thick, meduim weight, cold rolled mild steel, and fixed all as specified and directed.

S&FAluminium alloy, anodised, sliding door bolt 250 mm thick with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed.

SF in repair Aluminium alloy, anodised, sliding door bolt 250 mm thick with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed.

S&F Extruded aluminium alloy Handles 100mm size, fabricated type, anodised all as specified and directed.

S&F in repair Extruded aluminium alloy Handles 100mm size, fabricated type, anodised all as specified and directed.

S&F Extruded aluminium alloy Handles 150mm size, fabricated type, anodised all as specified and directed.

S&F in repair Extruded aluminium alloy Handles 150mm size, fabricated type, anodised all as specified and directed.

S&F 12mm thick perforated particle board/tiles for insulation and accoustic purpose, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid all as specified and directed.

S&F Anodised aluminium snap grid frame size 605 x605 mm work for false ceiling all as specified and directed by Engr-in- charge

M&L second class hard wood in clean sawn scantling all as specified and directed.

M&L Roof trusses 410-W (Gde E-250) quality A (framed). trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

M&L 2nd class Hard wood weather boarding, clean sawn, plain 20mm thick or feather edged 15 to 20mm thick and fixed with 30mm laps all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

M&L mild steel works for Banks, straps, supports or stays for rainwater, ventilating pipes, conforming to Fe290 Gde E165 including securing with purlins, truss or rafter complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

S&F 3-layer 25 mm thick PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion Welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc

Taking up or down steel tubing 15mm and connections, including cleaning for re- fixing or removal to store all as specified and directed.

Dismantling water tanks exc 250 and n.exc 500 and removing to store all as specified and directed.

S&F Rotational moulded poly- thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part Water tanks, exc 1000 ltr capacity all as specified and directed.

S&F in repair Wash basins, vitreous China (flat back or angle back type) 580x450mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as sepcified and directed by Engr-in- charge

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) all as specified and directed.

S&F in repairs, 10 ltr capacity High or low level PVC valveless, syphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets all as specified and directed.

S&F cast copper alloy chromium plated fancy type bib tap 15 mm bore all as specified and directed.

S&F 15mm bore brass CP Mixer for mixing hot & cold water screwed down for iron pipe and fixed all as specified and directed.

S&F PVC Connection 15mm with PTMT nuts of length 450mm long all as specified and directed.

S&F 15mm fancy type Chromium plated angle stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

S&F 25mm bore brass valve high pressure with polythene float with fly nut complete screwed for iron pipe or brass ferrule and fixed all as specified and directed.

S&F grating doom 100 mm dia of PTMT all as specified and directed.

S&F brass chromium plated tubular towel rail 20mm dia D type 60cm long all as specified and directed.

S&F CP soap dish, any type fixed to plugs with chromium plated brass screws all as specified and directed.

M&L providing and injecting anti termite chemical emulsion for post construction Anti termite Treatment along externall wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and directed.

S&F curtain rails anodised aluminium alloy with fixing brackets, stops, rollers etc all as specified and directed.

Excavating in trenches, hard/dense soil n.exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out all as specified and directed.

M&L Cement concrete 1:4:8 type D2 (40 mm graded aggregate) as in foundations, filling and mass concrete all as specified and directed.

M&L Reinforced cement concrete type BO 1:2:4 (12.5mm graded aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick fair finished surface of concrete all as specified and directed.

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified all as specified and directed.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2. Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard/dense soil all as specified and directed.

M&L Cement concrete 1:2:4 type B2 (40 mm graded aggregate) in foundations, filling and mass concrete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 all as specified and directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint. over a coat of red oxide primer all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, n exc. 10Cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide when unconnected with other painting or when painted in a different tint all as specified and directed.

M&L cement concrete 100mm thick type D-2, 1:4:8 (40mm gradede aggregate) for chequered path/ sub base of flooring.

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey pigment cement and pigment over 10mm thick screed bed in CM 1:4 all as specified and directed.

Surface excavation not exc. 30cm deep and averaging 15cm deep and getting out in hard/dense soil all as specified and directed.

M&L for removing excavated material exc.1.50Km but not exc 5Km and depositing where directed

M&L 150mm thick soiling (or sub base) with broken boulders or quarried stone,interstices filled, surface formed and rolled and considered to required gardient and camber all as specified and directed.

M&L for 50mm thick fine aggregate (sand) for laying of paver blocks all as specified and directed.

M&L 80mm thick machine pressed precast concrete interlocking paver block with grey cement and no pigment ,any shape and size confirming to IS 15658-2006 of M-40 Grade all as specified and directed.

M&L cement concrete type B0 1:2:4(12.5mm graded aggregate) in roof kerbs or mud stops,rounded or chamfered on edges all as specified and directed.

M&L 200mm thick cement concrete work in pavement/hard standing of flexural strength 40Kg/sqcm in field using 400kg of cement per cum all as specified and directed. Note: (i) The cement content given is the minimum content of the cement to be provided.In case any extra amount of cement is to be added as per mix design, nothing extra shall be paid to the contractor. (ii) Cost of submission of design mix for flexible concrete shall be included in the quoted rate (iii) Curing of concrete pavement shall be carried out by ponding of water after making bunds with CM 1:10 of suitable size (iv) Finishing to concrete surface bu belting or brooming shall be included in the quoted rate. (v) RMC for pavement shall be from approved plant only

Forming 12mm thick 200mm concrete slab expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound grade A all as specified and directed.

S&F polythene film black, 400 micron laid in floors completed all as specified and directed.

Forming construction joints 30mm deep 10mm wide filled with sealing compound grade A complete all as specified and directed.

Forming contraction joints (dummy) joints 65mm deep 10mm wide filled with sealing compound grade A all as specified and directed.

M&L for 2.5mmx2.5mm UV stabilised flame resistant rot proof non conductive knotted bird proof netting of 12/6 twisted polyethylene wires with mesh size of 19mm and weight of 22gm/Sqm and breaking strain of 20Kg per mesh and to be stable at sub zero temperatures and including tools frames,scaffolding etc and making good existing wall/ceiling surface by cleaning/plastering/painting etc if any disturbances occurred during the work and closing unnecessary openings with suitable materials all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be - made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. all as specified and directed.

M&L For One light point controlled by one switch with PVC single core unsheathed copper conductor multistranded cables FRLS 1.5 sq. mm size drawn through and including PVC conduit of suitable size concealed in wall and open conduit on ceiling and all acessaries, fire resitant, ISI Marked including standard size GE sheet pressed terminal box (recessed) with 3mm thick laminayed hylem sheet top cover including PVC single core unsheathed copper conductor multistranded cables FRLS 1.5 sq.as earth continuty conductor and makingn good the disturbed surfaces of walls/floors/ceiling etc all as specified and directed.

Same as per item No 103 but One ceiling fan point controlled by one switch all as specified and directed.

Same as per item No 103 but One exhaust fan point controlled by one switch all as specified and directed.

Same as per item No 103 but One 3 pin socket outlet 5 amps on the independent board all as specified and directed.

Same as per item No 103 but One 3 pin socket outlet 5 amps on same board all as specified and directed.

Same as per item No 103 but with cable 2.5 sqmm for One 3/5 pin socket outlet 15 amps on the independent board all as specified and directed.

Supply and fix Switch piano, flush type single pole, one way 5 Amp all as specified and directed.

Supply and fix Switch socket combination 2 in 1. 5 A flush type all as specified and directed.

Same as per item No 110 but 5A/16A, 5 in 1 flush type all as specified and directed.

S&F Ceiling rose, 3 phase /PVC/ polycarbonate, isolated body, 65 x 50mm, 3 terminals all as specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. all as specified and directed.

Supply and fix LED tube light fitting of 20 watt, Extruded aluminium housing enhances safety, high quality PC Diffuser, easy to install Efficacy 110/125 lumen/watt

Supply and fix LED tube light fitting of 10 watt. Extruded aluminium housing enhances safety, high quality PC Diffuser, easy to install Efficacy 110/125 lumen/watt

S & F LED 2 x 2 feet fitting, 36W, 230V,with CRCA Powder coated housing and high quality PC Diffuser, efficacy of 120 Lumen/watt, THD <10,L70 B50.. PF >0.95, with seperate driver module, complete with all accessories internally pre-wired and incl connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and directed..

M&L for submain wiring with 4 runs of single core 6 sqmm PVC insulated unsheathed multistranded copper conductor cable FRLS, ISI marked alongwith 2 runs of 4 sqmm multistranded insulated copper conductor cable as earth continuty conductor drawn through and including PVC conduit of suitable size on surface/ recessed as required. Note: 4 Runs of PVC wires of 6 sqmm and 2 run of 4 sqmm earth wire and one run condit will be measured as one unit) all as specified and directed.

Supply and fix thermoplastic polycarbonate VTPN DB, 4 way, 415 Volts with 205A bus bar, in accordance with IEC 61439-3 hinged double door type shock proof, Rust free, Corossion free, acid and chemical resistance, fire retardent, self extinguishing, PE+N terminals suitable to fix MCB/RCCB as incomer, IP 66 Protection, Flush type with glands, lugs etc for connection of cables including dismantling old one all as specified and directed. Make Hensel/Spelsberg/Rittal all as specified and directed.

Supply and fix thermoplastic polycarbonate SPN DB, 12 way/module, 220 Volts. in accordance with IEC 61439-3 hinged flap type shock proof, Rust free. Corrosion free acid and chemical resistance, fire retardent, self extinguishing PE+N terminals, IP 65 Protection including dismantling old one all as specified and directed. Make Hensel/Spelsberg/Rittal all as specified and directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20A all as specified and directed.

S&F MCB TPN 50 to 63 Amps.415 volts, 10 KA, C Series all as specified and directed.

S&F MCB SPN 32 Amps, 220 volts, 10 KA, 'C' Series all as specified and directed.

S&F MCB SP 6 to 32 Amps, 220 volts, 10 KA, 'C' Series all as specified and directed.

Supply and fix Environmental friendly, long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP66 Protection and impact resistant of IK07 of 45 watt all as specified and directed.

Taking down fan, sealing cable end,dismantling blades and removing fan and blades to store all as specified and directed.

M & L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. all as specified and directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed.

M & L for Earthing complete with GI Steel earth plate electrode 600 x 600 x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) earth plate paced on all side with charcoal mixed with salt to a thickness of 150mm in layers, with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth wire of size 4 mm, dia by means of bolts, nuts, check soldered and revetted to earth plate. Earth wire will be protected by using 20mm dia bore GI pipe light grade. The earthing includes PCC Pit chamber, RCC pit cover and frame, watering pipe 20mm bore, funnel with wire mess with necessary earth work including disposal of surplus soil to a distance not less than 50 mtrs etc complete all as shown in electrical plate No. 3 of SSR Part-1 2009, connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

M&L Cutting chases, pinning in brick wall, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings steps, cills, sunshades shelves, lintels etc and cutting chases for concealed water tubing or concealed wiring etc and making good cutting exceeding 20cm girth complete all as specified and directed.

Classic Builders

Yesgee Projects Private Limited