Tender For Conversion of T2 Terminal to Business Jet Terminal

Amount

(SH :- 1.0 - EARTHWORK) Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil, disposed earth to be levelled and neatly dressed, within the site as directed by the Engineer- in-Charge.

All kinds of soil

Ordinary rock

Earth work in excavation by means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth.1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil, disposed earth to be levelled and neatly dressed, within the site as directed by the Engineer- in-Charge.

All kinds of soil.

Earth work in excavation by means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth.1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil, disposed earth to be levelled and neatly dressed, within the site as directed by the Engineer- in-Charge.but for every additional lift of 1.5m to 3.00m or part there of :

All kinds of soil

Earth work in excavation by means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth.1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil, disposed earth to be levelled and neatly dressed, within the site as directed by the Engineer- in-Charge. but for every additional lift of 3.00m to 4.50m or part there of :

All kinds of soil

Extra for Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift from 1.5m upto 3.00m, disposed earth to be levelled and neatly dressed:All kinds of soil in or under water and or liquid mud, for pumping out water as required.( The depth measured from the sub soil water level up to the center of gravity of the quantity executed in difficult conditions.The depth of center of gravity shall be reckoned correct to 0.1m, 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.) unit of measurement will be cum per meter depth

Extra for Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift from 3m upto 4.50m, disposed earth to be levelled and neatly dressed:All kinds of soil in or under water and or liquid mud, for pumping out water as required.( The depth measu red from the subsoil water level up to the center of gravity of the quantity executed in difficult conditions.The depth of center of gravity shall be reckoned correct to 0.1m, 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.) unit of measurement will be cum per meter depth

Supply and Filling with earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 mm and lift up to 1.5 m as per direction of site Engineer-in-charge

Supply and Filling in plinth,or trenches, under floors, in areas with crusher sand including watering, ramming, consolidating and dressing cost and conveyance of all materials,labour charges,lead,lift etc complete at all levels as directed by the Engineer-in-Charge

Filling available excavated earth(excluding rock) in trenches, under floors,plinth,sides of foundation,in areas etc. in layers not exceeding 20cm in depth,consoldating each deposited layer by ramming and watering,lead upto 50m and lift upto 1.5m including cost and conveyance of all materials,labour charges, etc complete at all levels as directed by the Engineer-in-Charge.

Consolidation of earth by ramming in 15 cm layers including watering cost and conveyance of all materials ,labour charges etc complete as directed by the Engineer- in-Charge.

Disposal of Excavated earth/debris,and other unservicable materials by mechanical means upto a distance of 5 kms as directed by the Engineer-in-Charge.

(SH: - 2.0 - CONCRETE WORK) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete of specific grade properly mixed and consolidated with hand rammers/power troweller, including cost and conveyance of all materials, labour, curing, lead lift , etc. complete as directed by Engineer-in-Charge at all levels.

For screed concrete 1:2:4 (1 Cement : 2coarse sand : 4 graded stone aggregate 6mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification

Extra rate for PCC 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)in or under water and or liquid mud,including pumping out water and removing slush etc as required and as directed by the Engineer-in-Charge(The quantity will be calculated by multyplying the depth measured from the subsoil water level up to centre of gravity of concrete under sub soil water level with quantity of concrete in cubic meter executed under sub-soil water.The depth of center of gravity shall be reckoned correct to 0.1m, 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.) unit of measurement will be cum per meter depth

(SH: - 3.0 - R.C.C. WORK) Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M-25 grade conforming to IS 456 or IS 10262 for reinforced cement concrete structural elements,using coarse sand conforming to IS 383 and 20mm nominal size graded hard granite groken stones, excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in proportion of 0.5%of weight of cement (asper IS 9103) to accelerate,retard setting of concrete improve workability without impairing strength and durability as per direction of Engineer-in-charge for trenches, drain etc Minimum cement content is 400Kg/m3.

All works upto plinth level

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M-30 grade conforming to IS 456 or IS 10262 for reinforced cement concrete structural elements,using coarse sand conforming to IS 383 and 20mm nominal size graded hard granite groken stones, excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in proportion of 0.5%of weight of cement (asper IS 9103) to accelerate,retard setting of concrete improve workability without impairing strength and durability as per direction of Engineer-in-charge for column footings and grade beams of porches,holding tanks etc Minimum cement content is 410Kg/m3.

All work upto plinth level.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M-30 grade conforming to IS 456 or IS 10262 for reinforced cement concrete structural elements, using coarse sand conforming to IS 383 and 20mm nominal size graded hard granite groken stones,excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in proportion of 0.5%of weight of cement (asper IS 9103) to accelerate,retard setting of concrete improve workability without impairing strength and durability as per direction of Engineer-in-charge for slabs, beams, vertical walls, sunshades etc Minimum cement content is 410Kg/m3.

All work above plinth level upto floor V level.

Providing ,hoisting and fixing upto plinth level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, slabs,brackets etc. including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand conforming to IS383), cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 Cement : 3 fine sand) on exposed surfaces complete as per direction of Engineer-in-charge.but excluding the cost of reinforcement with design mix cement concrete of M-25 grade conforming to IS 456 or IS 10262.

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding with 16 gauge GI binding wire etc complete including cost, conveyance, lead, lift of all materials for all types of RCC works as per drawing/specification and as directed by Engineer-in-charge at all levels.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Edges of slab and breaks in floors and walls under 20 cms wide.

Weather shade, Chajjas, corbels etc., including edges.

Walls of (any thickness)including attached pilasters butteresses plinth and string course etc.

Extra for shuttering in circular work (20% of respective centering and shuttering items)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing 12 mm dia rebar.Embedment depths of 120mm as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed in hammer drill, diamond coring holes , including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels.

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing 10mm dia rebar. Embedment depths of 100mm as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corossion tested. The approved chemical shall be installed in hammer drill, diamond coring holes. including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels.

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing 20 mm dia rebar. Embedment depths of 200mm as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed installed in hammer drill, diamond coring holes, including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels.

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing 16 mm dia rebar. Embedment depths of 160mm as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corrosion tested. The approved chemical shall be installed in hammer drill, diamond coring holes , including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels.

Providing and supplying heavy duty injection adhesive for rebar fixing using Epoxy resin of 330/500ml HILTI HIT-RE 500 V3/or equivalent for fixing 8mm dia rebar. Embedment depths of 100mm as mentioned from the Structural consultants, including supplying two component system consisting of resin and hardener in 3:1 ratio; filling above mentioned mortar with standard dispenser before inserting rebar strictly as per the manufacturers recommendations.The installation and the setting instructions should be strictly followed as per the manufacturers recommendations.The chemical anchor shall carry ETA, COLA and DIBT approval and fire approval. Application can be done in both wet & dry concrete condition, corossion tested. The approved chemical shall be installed in hammer drill, diamond coring holes. including cost and conveyance of all materials, labour charges,tool rental charges, lead,lift etc complete as directed by Engineer-in-Charge at all levels.

Providing and supplying injection epoxy mortar with M8 dia threaded rod of grade 5.8 of minimum 5 micron galvanization to an embedment depth of 80mm. The product should be approved by ETA, ICC, CSTB, COLA, BZS with Shock approval, Seismic (C1 & C2) approval, Fatigue and Fire Approvals in anchors to use in cracked concrete, tested for service temperature of -40 deg. C to +80 deg. C. The chemical should have an ETA approval for 100 years age testing. The fastening should be designed as per guidelines of TR 029. Drilling hole with double flute type drill bits/ hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard battery dispenser along with piston plug. The installation and the setting instructions should be strictly followed as per the manufacturer’s recommendations. The adequate embedment depth & number of anchors to be calculated as per the codal provision & the report to be submitted to the project manager/ design engineer for approval. For zones with high seismicity, seismic designs are mandatory.

Providing and supplying injection epoxy mortar with M10 dia threaded rod of grade 5.8 of minimum 5 micron galvanization to an embedment depth of 90mm. The product should be approved by ETA, ICC, CSTB, COLA, BZS with Shock approval, Seismic (C1 & C2) approval, Fatigue and Fire Approvals in anchors to use in cracked concrete, tested for service temperature of -40 deg. C to +80 deg. C. The chemical should have an ETA approval for 100 years age testing.The fastening should be designed as per guidelines of TR 029. Drilling hole with double flute type drill bits/ hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard battery dispenser along with piston plug. The installation and the setting instructions should be strictly followed as per the manufacturer’s recommendations. The adequate embedment depth & number of anchors to be calculated as per the codal provision & the report to be submitted to the project manager/ design engineer for approval. For zones with high seismicity, seismic designs are mandatory.

Providing and supplying injection epoxy mortar with M12 dia threaded rod of grade 5.8 of minimum 5 micron galvanization to an embedment depth of 110 mm. The product should be approved by ETA, ICC, CSTB, COLA, BZS with Shock approval, Seismic (C1 & C2) approval, Fatigue and Fire Approvals in anchors to use in cracked concrete, tested for service temperature of -40 deg. C to +80 deg. C. The chemical should have an ETA approval for 100 years age testing. The fastening should be designed as per guidelines of TR 029. Drilling hole with double flute type drill bits/ hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard battery dispenser along with piston plug. The installation and the setting instructions should be strictly followed as per the manufacturer’s recommendations. The adequate embedment depth & number of anchors to be calculated as per the codal provision & the report to be submitted to the project manager/ design engineer for approval. For zones with high seismicity, seismic designs are mandatory.

Providing and supplying injection epoxy mortar with M16 dia threaded rod of grade 5.8 of minimum 5 micron galvanization to an embedment depth of 125 mm. The product should be approved by ETA, ICC, CSTB, COLA, BZS with Shock approval, Seismic (C1 & C2) approval, Fatigue and Fire Approvals in anchors to use in cracked concrete, tested for service temperature of -40 deg. C to +80 deg. C. The chemical should have an ETA approval for 100 years age testing.The fastening should be designed as per guidelines of TR 029. Drilling hole with double flute type drill bits/ hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard battery dispenser along with piston plug. The installation and the setting instructions should be strictly followed as per the manufacturer’s recommendations. The adequate embedment depth & number of anchors to be calculated as per the codal provision & the report to be submitted to the project manager/ design engineer for approval. For zones with high seismicity, seismic designs are mandatory.

(SH: - 4.0 - MASONRY WORK) Providing and constructing Solid concrete block masonry M-10 grade in C.M1:6(1cement, 6 coarse sand) with Solid blocks of 30x20x15 cm size and approved quality including scaffolding, raking out of joints,curing, cost and conveyance of all materials,labour, lead, lift, etc. complete for all types of masonry works in super structure above the highest plinth level as directed by Engineer-in-Charge at all levels.

Solid block masonry M10 grade using pre cast sold blocks (Factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part 1 of 1979 for Super structure up to floor two level for 10 cm thick wall in: Cm 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding etc complete

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry including cost and conveyance of MS bars etc complete as directed by Engineer-in-Charge

(SH: - 5.0. - JOINERY WORKS) Providing and fixing straight SSD580 sliding shower cubicle system with one fixed Set 1 panel and one sliding panel, consisting of glass in-line panel, glass sliding door, over hanging ball bearing rollers for sliding door, sliding door knob, pair of magnetic seal, magnetic support profile, door stopper, water disperser, wall connection profile, bracket for joining, glass protection seal, cover profile to clip into the bottom of the track, frame wedge, slide frame profile, frame bracket, cover profile angular, square profile and glass guide to guide the sliding door. Glass thickness for fixed and moving panels will be 8 mm with max door weight of 30 kgs. Fix panel and door panels overlap by approx 40 mm. Standard system height will be 2000 mm and width shall be 2500 mm maximum. Finish of rollers, door knob and all aluminium profiles should be polished chrome. Sealant shall be used at corners and bottom of fixed panel.

Providing and fixing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).The rate shall includes cost and conveyance of all materials,labour , lead, lift, etc. complete as directed by Engineer-in-Charge at all levels. ( second class teak wood)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately,but inclluding cost for design and patterns as approved and all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) ( second class teak wood)

Second class teak wood 35 mm thick shutters for decorative doors

Providing and fixing of Hollow metal fire rated doors as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall have doors tested at CBRI for maximum rating of 2hrs tested . Individual Test certificates should also be available for glass used in vision lites confirming the required fire ratings /panels being a part of the fire door assembly. Doors should be finished in Thermosetting Powder Coating desired RAL Shades. Manufacturer test certificate shall cover doors both single & double leaf doors and Hardwares should pass European certificate "CE" of conformity / UL with required fire ratings. Any deviation in specification and sheet thickness other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Door frame shall be double rebate profile of minimum size 153mm X 77 mm made out of 1.50mm minimum thick galvanized steel sheet. NDRF 153x77 Frames shall be Butt jointed and field assembled with self bolted. The frames should be finished with Thermosetting Powder Coating in desired RAL Shade. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Door leaf shall be minimum 49mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 1.00mm minimum thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be Rockwool/ Honeycomb treated with Viper FRS 881 LH. All doors NSD 12049 shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided as per manufacturers recommendation with a beeding and screws from inside. However the glass should be clear 120 min fire rated Keralite of 5mm from Saint Gobain.The rate shall includes the cost and conveyance of all materials,labour charges,lead,lift, fire rated hardware like SS ball bearing hinges - 02 Nos.in each panel, Magnetic catch , SS D type Pull handle etc. as directed by the Engineer in Charge at all levels.

SD1 - Duct door size 1200x2400mm with vision panel 200x300mm FR glass

SHD2 - Fire Duct Door size of 1000x1800mm with vision panel 300x300mm using 5mm thick FR glass

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

Providing and fixing powder coated aluminium work for doors ,windows& partitions with extruded built up standard tubular sections/appropriate Z sections & other sections of approved make confirming to IS:733 & IS:1285 fixed with rawl plugs & screws or with fixing clips including necessary filling up of gaps at junctions,at top,bottom & sides with required PVC/neoprene felt etc.Aluminium sections shall be smooth,rust free,straight,mitred & jointed mechanically where ever required including cleat angle,aluminium snap beading for glazing/panelling,cp brass/stainless steel screws,removing the stickers clearly all complete as per architectutral drawings & directions of Engineer-in-Charge at all levels.(glazing & panelling to be paid seperately).Minimum thickness of powder coating for powder coated Aluminium shall be 50 micron.

For fixed portion

For shutter of doors ,windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings,exhaust fan of required size,etc wherever required including the cost of PVC neoprene gasket required(fittings shall be paid for separately)

Providing and fixing glazing with float glass panes in aluminium doors & windows/ aluminium/other partitions for glazed openings with PVC/ neoprene gasket etc. complete as per the architectural drawings and as directed by Engineer-in-Charge at all levels.

with float glass panes of 5.00mm thickness

with float glass panes of 4.00mm thickness

Providing and fixing 12 mm thk prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade I Type II, in panelling fixed in aluminium doors,windows shutters and partition frames with C.P. brass / stainless screws etc complete as per architectural drawings and directions of Engineer-in-Charge at all levels.Pre laminated particle board with decorative lamination on both sides. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer of approved make (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete as directed by the Engineer-in- Charge at all levels.

Providing and fixing 125 mm aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete as directed by Engineer -in-Charge at all levels.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness.

Providing and fixing bright finished brass100mm mortice latch and lock ISI marked with 6 levers and a pair of anodised(anodic coating not less than grade AC 10 as per IS:1868)aluminium lever handles with necessary screws etc. complete at all levels.(best make of approved quality).

Supplying and fixing of Frameless fully openable Patch Fitting door of 10mm thick clear toughened glass. The glass shutter should be polished on the edges. The shutter should be mounted with required Floor Spring with SS cover plate, with adjustable spring strength depending on door width, 25mm dia 450mm long SS pull handles, top and bottom patch, central patch lock, door stopper etc. All hardwares are of SS satin finish, 304 grade unless other wise mentioned.The rate shall includes cost and conveyance of all materials, all structure if any to support the patch fitting door,all hardwares, labour charges, lead, lift, etc complete as directed by Engineer in Charge at all levels. The Patch Fittings & Floor Spring fittings shall conform to EN 1154 Standards with adjustable spring strength (EN1-4)

Providing and fixing SS-304 grade 2 bearing butt hinges of approved size as per EN 1935, CE Marked. Suitable for door weights upto 120kgs including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer in Charge.(The purchase price considered for butt hinge is Rs.362/no excluding GST and any deviation plus or minus in the purchase price will be adjusted (paid extra or deducted) while making payment to the contractor).

Providing and fixing cam action door closer with G-N slide channel arm for pull side fixing. Spring size EN 2-4 as per EN 1154 and CE marked, Silver finish, with necessary accessories like SS 304 screws etc, including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer-in-Charge at all levels.(The purchase price considered for door closer is Rs13703/no excluding GST and any deviation plus or minus in the purchase price will be adjusted(paid extra or deducted) while making payment to the contractor)

Providing and fixing Mortice dead lock with 55mm backset, 20mm square forend and prepared for euro profile cylinder including strike plate in satin stainless steel as per EN 12209, CE marked of SS-304 grade including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer in Charge at all levels.(The purchase price( excluding GST) of mortise lock should be taken as Rs 2595/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing 6Plus 6 Pin Euro Profile Double Cylinder with Both side Key operation Under Master Key System.Total Length = 70mm (35mm+35mm)Change Keys - 3 Nos.Finish - Nickel Plated.(The purchase price( excluding GST) should be taken as Rs2661/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing 6 pin Euro profile cylinder with both side key operation standard length 70mm in satin nickel plated finish with 3 keys. Optional master keying and grand master keying can be done on request. -NMK(The purchase price( excluding GST) should be taken as Rs935/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing escutcheons prepared for euro profile cylinder suitable for dead lock in satin stainless steel.(The purchase price( excluding GST) should be taken as Rs240/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing D type pull HandleAntiviral/antimicrobial TGDI-D 300 back to back with adjustable fixing for glass, wood and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on the outer surface. Length =300mm, 22mm dia, -SS304with Antiviral / Antimicrobial coating - clear & transparent coating with protection tested for antibacterial activity with up to 99.9% effectiveness* as per ISO 22196 and antiviral activity with 99.9% reduction as per ISO 21702approved finish and make with all fixtures and necessary ss screws etc.including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer-in-Charge at all levels ..(The purchase price( excluding GST) should be taken as Rs2570/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing SS- 304 grade floor mounted door stop half dome of approved make and design in SS satin finish, with necessary accessories etc. including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer in Charge.(The purchase price considered for door stopper is Rs.253/no excluding GST and any deviation plus or minus in the purchase price will be adjusted (paid extra or deducted) while making payment to the contractor).

Providing and fixing Anodized Satin Clear finish silicone Auotmatic Door Bottom Seal, Concealed mounted in a 15mm x 34mm groove. Max gap 13mm. Finish: Anadoised satin clear. L=1220mm,concealed Mounted Version, spring loaded to lift clear of the floor as soon as the door leaf is opened, including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer-in-Charge at all levels.(The purchase price considered for bottom seal is Rs 4952/no excluding GST and any deviation plus or minus in the purchase price will be adjusted(paid extra or deducted) while making payment to the contractor).

Providing and fixing Delta Seal for acoustic, fire and smoke protection, suitable for wooden and steel frames, self adhesive, Finish = Black, Length = 1 x 1000mm, Height- 2 x 2750mm(The purchase price( excluding GST) should be taken as Rs 4612/no. and any deviation plus or minus in the purchase price( excluding GST)will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Mortice dead lock 278a with 55mm backset, 20mm square forend an dprepared for euro profile cylinder including strike plate in satin stainless steel as per EN 12209.of SS-304 grade including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer in Charge at all levels.(The purchase price( excluding GST) of mortise lock should be taken as Rs 2143/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.Mortice dead lock 278a with 55mm backset, 20mm square forend an dprepared for euro profile cylinder including strike plate in satin stainless steel as per EN 12209.

Providing and fixing 6Plus 6 Pin Euro Profile Double Cylinder with Both side Key operation Under Master Key System.Total Length = 60mm (30mm+30mm)Change Keys - 3 Nos.Finish - Nickel Plated.(The purchase price( excluding GST) should be taken as Rs 2412/no. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing 6 pin Euro profile cylinder with both side key operation standard length 60mm in satin nickel plated finish with 3 keys. Optional master keying and grand master keying can be done on request. -NMK(The purchase price( excluding GST) should be taken as Rs835/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing SS- 304 grade wall mounted door stop dome with 60mm length approved make and design in SS satin finish, with necessary accessories etc. including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer in Charge.(The purchase price considered for door stopper is Rs587/no excluding GST and any deviation plus or minus in the purchase price will be adjusted (paid extra or deducted) while making payment to the contractor).

Providing and fixing mop plate 1010-1 with smoothened edges and rounded corners flush face fixing screws height 150mm and thickness 0.9mm in SS 304 grade in satin satinless steel. Length=5mm short of the shutter width. Max door width =900mm(The purchase price( excluding GST) should be taken as Rs 4514/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing kick plate 1020-1 with smoothened edges and rounded corners flush face fixing screws height 300mm and thickness 0.9mm in SS 304 grade in satin satinless steel. Length=5mm short of the shutter width. Max door width =900mm(The purchase price( excluding GST) should be taken as Rs 5278/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Mortice sash lock 271a with 55mm backset, 20mm square forend with 72 mm centers and prepared for euro profile cylinder including strike plate in satin stainless steel as per EN 12209.(The purchase price( excluding GST) should be taken as Rs 1363 /no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Antiviral / Antimicrobial Pure Lever handle 8100 lever with roses, escutcheons prepared for Euro profile cylinder and spindle 8mm x 8mm x 110mm in satin stainless steel. Complete set including the fixing accessories for 50 mm thick door. with Antiviral / Antimicrobial coating - clear & transparent coating with protection tested for antibacterial activity with up to 99.9% effectiveness* as per ISO 22196 and antiviral activity with 99.9% reduction as per ISO 21702.The rate shall includes the cost and conveyance of all materials, labour charges, lead, lift etc complete as directed by the Engineer in Charge at all levels.(The purchase price( excluding GST) of lever handle with sash lock should be taken as Rs 2550/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor

Providing and fixing 6Plus 6 Pin Euro Profile with Key & Thumbturn operation Under Master Key System.Total Length = 60mm (30mm+30mm)Change Keys - 3 Nos.Finish - Nickel Plated .(The purchase price( excluding GST) should be taken as Rs 2532/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing, 6pin Euro profile knob cylinder with internal thumb turn and external key operation standard length 60mm in satin nickel plated finish with 3 keys. Optional master keying and grand master keying can be done on request. -NMK (The purchase price( excluding GST) should be taken as Rs 1218/no. and any deviation plus or minus in the purchase price( excluding GST)will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Male /Female sign plate 3020-M /3030-F , for WC application with fixing screws size 125 x 125mm, rounded corners in SS 304 satin stainless steel finish. Marking in black (The purchase price( excluding GST) should be taken as Rs 2780/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Wall mounted door stop with coat hook in Satin finish Stainless steel (The purchase price( excluding GST) should be taken as Rs 597/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.Profile with Key

Providing and fixing mop/Kick plate 1010-2 with smoothened edges and rounded corners flush face fixing screws height 150mm and thickness 0.9mm in SS 304 grade in satin satinless steel. Length=5mm short of the shutter width. Max door width =1000mm (The purchase price( excluding GST) should be taken as Rs 6388/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Male/Female sign plate 3020-M for WC application with fixing screws size 125 x 125mm, rounded corners in SS 304 satin stainless steel finish. Marking in black (The purchase price( excluding GST) should be taken as Rs 597/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Mortice WC lock 275a with 55mm backset, 20mm square forend with 78 mm centers and prepared for 8mm bathroom follower including strike plate in satin stainless steel as per EN 12209.(The purchase price( excluding GST) should be taken as Rs 1377/no. and any deviation plus or minus in the purchase price( excluding GST)will be adjusted(paid extra or deducted) while making payment to the contractor

Providing and fixing WC THUMBTURN with 8mm Spindle, One side indicator and other side Thumb Turn.(The purchase price( excluding GST) should be taken as Rs 1200/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor

Providing and fixing 6 piin Euro profile knob cylinder with internal thumb turn and external coin operation standard length 60mm in satin nickle plated finish. NMK.(The purchase price( excluding GST) should be taken as Rs 1197/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor

Providing and fixing Grab Bar of Length 610mm, 25mm Diameter in Satin stainless Steel Finish..(The purchase price( excluding GST) should be taken as Rs 2500/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Disable sign plate 3040-D for WC application with fixing screws size 125 x 125mm, rounded corners in SS 304 satin stainless steel finish. Marking in black.(The purchase price( excluding GST) should be taken as Rs1617/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Mortice sliding door 400 claw bolt with 55mm backset, 22mm sq forend including strike plate in satin stainless steel. 3015 WC EPC 60mm Length internal thumb turn & external COIN release & Escutcheons in SSS Finish.(The purchase price( excluding GST) should be taken as Rs 2200/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing flush pull for sliding door, rectangular. Finish - Satin stainless steel (The purchase price( excluding GST) should be taken as Rs1572/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Automatic door bottom RP8si seal fromextruded silicon sealing component, spring loaded to lift clear of the floor. Concealed mounted in a 15mm x 34mm groove. Max gap 13mm. Finish: Anadoised satin clear. L=1063mm(The purchase price( excluding GST) should be taken as Rs4055/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Automatic door bottom RP8si seal from ,extruded silicon sealing component, spring loaded to lift clear of the floor. Concealed mounted in a 15mm x 34mm groove. Max gap 13mm. Finish: Anadoised satin clear. L=820mm(The purchase price( excluding GST) should be taken as Rs 2900/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing 6Plus 6 Pin Euro Profile Single Cylinder with Single side key operation Under Master Key system.Total Length = 43mm.Change Keys - 3 Nos.Finish - Nickel Plated .(The purchase price( excluding GST) should be taken as Rs1882/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing , 6 pin Euro profile half cylinder with one side key operation standard length 42mm in satin nickel plated finish with 3 keys. Optional master keying and grand master keying can be done on request. -NMK.(The purchase price( excluding GST) should be taken as Rs713/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Recessed Oval Flush Pull Handle 1207, SSS (The purchase price( excluding GST) should be taken as Rs327/no. and any deviation plus or minus in the purchase price( excluding will be adjusted(paid extra or deducted) while making payment to the contractor.

Providing and fixing Automatic door bottom RP8si seal from ,extruded silicon sealing component, spring loaded to lift clear of the floor. Concealed mounted in a 15mm x 34mm groove. Max gap 13mm. Finish: Anadoised satin clear. L=920mm(The purchase price( excluding GST) should be taken as Rs3413/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor

Providing and fixing G GSR-System Slide channel door co-ordinator with thrust rod clamp system,complete, non-handed (The purchase price( excluding GST) should be taken as Rs24220/no. and any deviation plus or minus in the purchase price( excluding GST will be adjusted(paid extra or deducted) while making payment to the contractor

Providing and fixing lever action flush bolt with 19mm projecting bolt L=172 mm for wood door in satin chrome (The purchase price( excluding GST) should be taken as Rs1017/no. and any deviation plus or minus in the purchase price( excluding GST)will be adjusted(paid extra or deducted) while making payment to the contractor

Providing and fixing lever action flush bolt with 19mm projecting bolt L=300 mm for wood door in satin chrome (The purchase price( excluding GST) should be taken as Rs1217/no. and any deviation plus or minus in the purchase price( excluding GST)will be adjusted(paid extra or deducted) while making payment to the contractor

Proving and fixing dust excluding socket 3124 with 16mm dia hole, fully morticed on the floor. satin chrome (The purchase price( excluding GST) should be taken as Rs 362/no. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor

(SH: - 6.0 - STEEL WORK) Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coats of syntheic enamel paint all complete.

Structural steel work welded in built up sections,trussess and framed work including cutting, hoisting, fixing in position and applying two coats of Synthetic enamel paint over two coats of anticorrossive Yellow zinc chromate primer including cost and conveyance of all materials,labour charges ,lead,lift etc complete as directed by Engineer- in-Charge at all levels.

Steel work welded in built up sections/framed work including cutting hoisting, fixing in position and applying two coats of approved make and colour synthetic enamel paint over two coats of approved make anticorrossive yellow zinc chromate primer, etc. including cost and conveyance of all materials, labour, lead,lift etc. complete as directed by Engineer- in-Charge at all levels.

In stringers, treads, landings etc of staircases including use of chequered plate wherever required all complete.

In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.

Steel work in built up tubular sections YST 310 grade as per IS: 4923 trusses and framed works including cutting, bending, hoisting, fixing in position, welded and bolted including special shaped washers etc. complete with electric resistance or induction butt welded tubes including painting with two coats of approved make and colour synthetic enamel paint over two coats of approved make anticorrossive yellow zinc chromate primer, closing all the open ends properly with same material cost and conveyance of all materials, labour, etc., complete as directed by the Engineer-in-Charge at all levels.

Supplying and fixing electrically operated rolling shutters of approved make, made of required size GI laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, GI side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS:4454 part 1 and GI top cover of required thickness for rolling shutters including two coats of approved make and colour synthetic enamel paint over two coats of approved make anticorrossive yellow zinc chromate primer, including cost and conveyance of all materials, labour charges,lead,lift etc complete as directed by Engineer in Charge at all levels. 80 x 1.25mm GI laths with 1.25mm thick top cover

Providing and fixing ball bearing for rolling shutters including cost and conveyance of all materials, labour, etc. as directed by the Engineer-in-Charge at all levels.

Extra for providing capsule type GI rolling grill for rolling shutter instead of laths as per the design approved by the Engineer-in-Charge(area of grill to be measured)

Glass handaril Fabrication, supply & installation of Top mounted SS -304grade railing as per drawing made of 63mm dia. 16 gauge SS top rail mounted on SS baluster hollow 63mm dia. pipe of 16 gauge with CNC made SS modular neck of 25mm dia. to hold the top rail. Balusters are spaced at 1.20 m regular intervals. The total height of the rail including top rail will be 1200 mm from FFL. The baluster will infill with 13.52 mm thk. laminated H.S Glass panels (6 mm H.S + 1.52 mm PVB + 6 mm H.S ) with height 650 mm & length as per layout) connected to the baluster with 2 Nos. of CNC made SS modular glass holder . Further the baluster is top mounted with SS-304 grade base plate of 125 dia. x 8 mm thk. fixed on the floor with GI anchor fasteners. All SS components are in SS-304 grade in satin finish, made using modern, automatic machines like CNC machine, robotic welding, laser cutting, water jets etc.The rate shall includes cost and conveyance of all materials,base plate ,screws ,bolts , fabrication,any locking arrangements, transportation, cutting and making good the floors,loading and unloading, handling of machineries all electrical charges etc. labour charges, lead, lift etc. complete as per drawing and directed by Engineer-in-Charge. (The above work shall be carriedout by an agency having sufficient experience glass works and should ensure a guarantee of 5 years. Only skilled and experienced persons shall be employed for this purpose.)

Fabrication, supply & installation of Top mounted SS - 304grade staircase railing 1050mm Ht from FFL as per drawing, made of SS top rail of 63mm dia. 16 gauge hollow pipe mounted on SS baluster of 63mm dia. 16 gauge hollow pipe, with CNC made SS solid neck to hold the top rail. Balusters are spaced at 1.20 m regular intervals. .Top rail connected to balusters with 25mm dia SS modular solid neck.The baluster will infill with 6nos of equally spaced horizontal mid rails of dia 25mm dia 16 gauge SS hollow pipe, connected to the baluster with 6 Nos.Further the baluster is top mounted with SS baseplate of 125 Dia. x 8 mm thk. fixed on the floor with GI anchor fasteners as per drawing. All SS components are in SS-304 grade in glossy finish, made using modern, automatic machines like CNC machine, robotic welding, laser cutting, water jets etc. The rate shall includes cost and conveyance of all materials,base plate ,screws ,bolts , fabrication,any locking arrangements, transportation, cutting and making good the floors/walls,loading and unloading, handling of machineries all electrical charges etc. labour charges, lead, lift etc. complete as per drawing and directed by Engineer-in-Charge.

SS Bollard Providing and fixing SS 304 grade, 1000mm height,150mm dia ,thickness 3.15mm bollards as per drawing including fixing with a MS base plate of size 200x200x10mm. The rate shall includes cost and conveyance of all materials,base plate ,screws ,bolts , fabrication, transportation, cutting and making good the floors,loading and unloading, handling of machineries all electrical charges etc. labour charges, lead, lift etc. complete as per drawing and directed by Engineer-in-Charge.

Guard rail for glass partition Fabrication, supply & installation of Floor mounted SS-304 grade guard Railing at 300 mm height from FFL as per drawing, made of 50mm Dia.16 gauge .Further the SS bracket mounted on SS base plate of Dia. 100 x 6 mm thk. fixed on the floor with anchor fasteners.All SS components are in SS-304 grade in glossy finish, made using modern, automatic machines like CNC machine, robotic welding, laser cutting, water jets etc.The rate shall includes cost and conveyance of all materials,base plate ,screws ,bolts , fabrication, transportation, cutting and making good the floors,loading and unloading, handling of machineries all electrical charges etc. labour charges, lead, lift etc. complete as per drawing and as directed by Engineer-in-Charge.

Supplying and fixing C.I with out frame for manholes: 560 mm diameter ( heavy duty) the weight of the cover to be not less than 108 kg

Supply and fixing SS manhole cover of size 600x600 mm as per manufactureres specification suitable for granite flooring upto 20mm thick, with concrete filling( concrete will be measured and paid seperately) as directed by engineer in charge. The purchase price( excluding GST) should be taken as Rs.20000/each. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor

Steel work in built up tubular sections YST 310 grade as per IS: 4923 trusses and framed works including cutting, bending, hoisting, fixing in position, applying a priming coat of approved steel primer and welded and bolted including special shaped washers etc. complete with electric resistance or induction butt welded tubes closing all the open ends properly with same material cost and conveyance of all materials, labour, etc., complete as directed by the Engineer-in-Charge at all levels.

(SH: - 7.0 - FLOORING WORK) Providing and laying double charged polished /matte vitrified tile flooring (any shade) 1000x 1000 mm, 11-12 mm thick with water absorbtion less than 0.05% of first quality confirming to IS:15622 with each tile having abrasion resistance less than 144 cubic mm,breaking strength greater than or equal to 3000N, scratch hardness minimum 6,MOR >=40 which is stain resistant and chemical resistant of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive conforming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980 ,including cost and conveyance of all materials, labour charges,lead, lift,curing, etc, complete and tile protection till handover as directed by Engineer in charge at all levels. The rate includes cutting the sharp edges of tiles with specialised machinery wherever required . The purchase price( excluding GST) of double charged polished/matte vitrified tile should be taken as Rs1172/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing and laying double charged polished/matte vitrified tile skirting/dadoing (any shade) 1000 x 1000 mm, 11- 12 mm thick with water absorbtion less than 0.05% of first quality confirming to IS:15622 with each tile having abrasion resistance less than 144 cubic mm, breaking strength greater than or equal to 3000N, scratch hardness minimum 6,MOR >=40 which is stain resistant and chemical resistant of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980, including cost and conveyance of all materials, labour charges,lead, lift,curing, etc, complete as directed by Engineer in charge at all levels. The rate includes cutting the sharp edges of tiles with specialised machinery wherever required . The purchase price( excluding GST) of double charged polished/matte vitrified tile should be taken as Rs1172/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor. in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing & fixing flooring transition profile at transitions between different flooring,having size of 30 mm wide and up to 5 mm high as per manufacturer’s standard. The finish of the profile is glosy Stainless Steel as approved by the Engineer-in-Charge . The profile is to be fixed with adhesives per manufacturer’s specification and as approved by the Engineer-in-Charge. The rate shall includes the cost and conveyance of all materials,adhesive labour charges,lead, lift, complete as directed by Engineer-in-Charge at all levels The purchase price ( including tax)of transition profile to be considered as Rs 1025/m any deviation plus or minus in the purchase price( including tax) in approved shade will be adjusted while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing and fixing Vitrified floor tiles 600x600x9 mm of Ist quality conforming to IS : 15622 of approved make,shade,and pattern , water absorbtion less than 0.08% of first quality confirming to IS:15622 laid with cement based high polymer modified quickset adhesive conforming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980 ,including cost and conveyance of all materials, labour charges,lead, lift,curing, etc, complete and tile protection till handover as directed by Engineer in charge at all levels. The rate includes cutting the sharp edges of tiles with specialised machinery wherever required . The purchase price(excluding tax) of Polished vitrified tile should be taken as Rs 700/sqm. and any deviation plus or minus in the purchase price(excluding tax) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing and laying Polished/matte vitrified tile skirting/dadoing of range 600 x 600 mm -605 x 605 mm, 9.0- 10 mm thick which is stain resistant and chemical resistant of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980 ,including cost and conveyance of all materials, labour charges,lead, lift, curing, etc, complete and tile protection till handover as directed by Engineer in charge at all levels. The rate includes cutting the sharp edges of tiles with specialised machinery wherever required . The purchase price ( excluding GST) of double charged Polished Double charged vitrified tile should be taken as Rs700/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing and installing modular floor matting with 17.5mm thickness in tile profile, open structure, unbacked for dirt removal application, in outdoor and indoor areas.The floor mats should be installed in recessed-well areas and normal flooring (with edging).Specially designed for high foot traffic & trolley traffic.The mat should be made from flexible vinyl material with recommemded Weight of 10.1kg/sqm. The matting should be motor oil resistant and suitable for heavy duty foot traffic in dry or wet areas. The matt should be suitable for Removal of grime, muck, wet and dry sticky soil .It should also serves to scrape off and collect dirt which helps prevent dirt from being tracked into a building and holds dirt away from the floor surface. The rate is including cost and conveyance of all materials, labour charges,lead, lift,curing etc, complete and protecton till handover as directed by Engineer in charge at all levels The purchase price( including tax) of matting should be taken as Rs.34445/sqm. and any deviation plus or minus in the purchase price( excluding tax) in approved material will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.

Providing and laying Brushed Sadarahalli /approved Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.(The purchase price( including tax) of Granite stone slab should be taken as Rs.1800/sqm and any deviation plus or minus in the purchase price( including tax) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor).

Heavy duty tile Providing and laying Vitrified exterior floor tiles 600x600x16 mm or nearest thickness of approved quality make,shade,and pattern confirming to IS:15622 with breaking strength greater than or equal to 7000 N ,MOR >=38,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.including cost and conveyance of all materials,labour charges,lead,lift etc, complete as directed by the Engineer in Charge at all levels.(The purchase price of tiles shall be taken as Rs.1130/sqm and any deviation plus or minus in the purchase price in approved shade will be adjusted in the price quoted).

Providing and fixing machine cut, mirror / eggshell polished ,18 +-2mm thick Italian Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1cement : 3 oarse sand) laid and jointed with white cement slurry @ 3.3kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. The rate includes cost and conveyance of all materials, labour charges,lead, lift, curing, etc, complete and protection till handover as directed by Engineer-in-Charge at all levels.The rate includes cutting the sharp edges of stones with specialised machinery wherever required . The purchase price( including tax) of Italian Marble stone should be taken as Rs 4844/sqm. and any deviation plus or minus in the purchase price( including tax) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing and applying self levelling compound upto 3mm thick including primer(acrylic based) for the high performance and correction of irregular substratas( low co2 emmission and very low volatile organic compound emissions recycable) for attaining a levelled surface for vinyl, wooden flooring etc with a mixing ratio of 6.5litre of clean water to 25 kg bag using HDE technology with extended flow including cost and conveyance of all materials, labour, curing, lead lift , etc. complete as directed by Engineer-in-Charge at all levels.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing and laying Laminated wooden flooring using 8mm thick Plank Sizes - 1214x192x8mm / 1286x192x8mm size in approved design/ pattern with micro beveled shaped edges including installing the laminated wood using four side buckled "Click" system with tongue and groove mechanism. Sub floor on which the planks are being laid should be smooth, flat & hard & free from moisture, greases, etc . In case of uneven sub floor the same should be leveled by self leveling compound(measured and paid seperately). The moisture level present in the sub floor should be less than 8% before installation of the floor. The laminated wood must be installed on a thin layer of PU form underlay to keep the wood safe from moisture below and keep it noise proof. The planks can be fixed easy with its “Lock & Fold” installation system. The installation should be carried out as per the manufacturer installation guide and process.,including cost and conveyance of all materials,PU underlay labour charges,lead, lift,curing, complete as directed by Engineer in charge at all levels .The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose. The purchase price( excluding tax) of planks should be taken as Rs 1184/sqm. and any deviation plus or minus in the purchase pricewill be adjusted(paid extra or deducted) while making payment to the contractor

Providing and laying in correct line and level 60mm thick cement concrete flooring with 1:2:4 (1 cement: 2 coarse sand 4 graded stone aggregate, 65% 20mm metal and 35% 12mm metal)mixing admixtures in recommended proportion (asper IS 9103) to accelerate,retard setting of concrete improve workability without impairing strength and durability.Providing bull marks on the floor area one day prior for getting proper level. Applying by sprinkling carborundum based floor hardeners of approved make on the top of concrete at the ratio of 5kg/m2.Finish the concrete using power floater and power trowel for smooth finish including watering ,curing, cleaning etc..and cutting the grooves in 4mx 4m, 5mm width x20mm depth with mechanical concrete groove cutting machines and filling the groove with approved epoxy sealants. Rate shall include cost and conveyance of all material, labour etc.. Complete as directed by Engineer - in Charge.(All works covered by this specification shall be carried by an experienced agency having sufficient experience in this type of flooring system Only skilled and experienced persons shall be employed for this purpose.)

Providing and laying machine cut, mirror polisheditalian marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 16+-1mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified andas directed by the Engineer-in-Charge. The rate includes cost and conveyance of all materials, labour charges,lead, lift, curing, etc, complete and protection till handover as directed by Engineer-in-Charge at all levels. The purchase price( excluding GST) of stone should be taken as Rs 4844/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose. A thin layer of PU form underlay to be laid below the flooring to keep the floor safe from moisture

Providing and fixing 18 to 20 mm thick granite slab gang saw cut , mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.The purchase price( excluding GST) of granite stone should be taken as Rs 3000/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing and laying Natural teak wood flooring using 15mm thick150cm length and 9cm width in approved design/ pattern.The surface shall be suitably cleaned by using sand paper, filling of grains with wood filler and dent filler, applying approved wood stain as per the direction of Engineer-in -Charge for getting required shade, applying 2 coats of PU sealer, sanding the surface after applying PU sealer and applying 2 coats of PU ceramic/glossy/matt top coat. etc complete as per drawing complete as directed by Engineer in charge.The purchase price( excluding GST) of teak wood planks should be taken as Rs 7000/sqm. and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Extra for inlay work in marble flooring over the respective marble flooring item as per approved drawing including finishing and polishing the surface as per the direction of engineer in charge..

Supply and installation of Premium Hand Tufted carpet manufactured using High Density imported hand spun New Zealand Wool (Semi Worsted Wool) of approved designs, patterns and colours. PU foam underlay for extra cushioning. Pile - Cut Pile. Material – Semi Worsted New Zealand Wool . Pile Height - 10 -12 mm. Pile Weight - 4500 GSM. The construction is Hand Tufted type with Superior Quality Synthetic Waterproof Latex with Canvas Backing provided.The purchase price( excluding GST) should be taken as Rs 16463/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/granite work including providing necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete as directed by the Engineer-in-Charge at all levels.

Providing and laying Polished Engineered Quartz stone flooring with 15 mm thick slab 10ft x 4 ft with water absorbtion less than0.02%, flexural strength in the range of 28-60, compressive strength greater than 150, surface hardness in the range of 6-7, glossiness reflection greater than 60%, of approved make, shade and pattern laid with cement based high polymer modified quickset adhesive confirming to IS:15477, in minimum 6mm thickness (as per manufactures' specification) with 2mm spacers and expansion and contraction joints wherever necessary with spacer filing with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confining to British standards 5980:1980 including cost and conveyance of all materials, labour charges,lead, lift,curing, complete as directed by Engineer in charge at all levels. The rate includes cutting the sharp edges of stones with specialised machinery wherever required . The purchase price( including tax) of Polished Engineered Quartz stone should be taken as Rs 3500/sqm. and any deviation plus or minus in the purchase price( including tax) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The above work shall be carried out by an agency having sufficient experience in flooring and only skilled and experienced persons shall be employed for this purpose.

Providing & fixing water cooler ledge wall as per drawing formed out of 12mm thick solid surface(Corian) of approved make and colour fixed to 9mm thk bison board backing using adhesive and necessary screws .The bison board is fixed to the existing frame work using screws and adhesive etc.fascia formed to shape, polished to gloss. The rate shall includes ,cost and conveyance of all materials, cutting and polishing the material, labour charges,lead,lift etc. complete as per technical specification and as directed by the Engineer in charge at all levels . The rate includes cutting the edges of solid surface(Corian) buffing, and making necessary openings,inlet and out let water provisions with specialised machinery wherever required for all fixtures. The above work shall be carried out by an agency having sufficient experience in concerned work and should ensure a guarantee for any defective installation and material composition for a period of 10 years from the date of completion of the said work .only skilled and experienced persons shall be employed for this purpose.

Providing edge moulding to 18 mm thick granite for column bases , counters, Vanitiesetc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge.

Providing and applying Antitermite treatment by injecting chemical emulsion Imidacloprid emulsiable concentrate .075% for post-constructional treatment and creating a chemical barrier as per relavent code and engineering practice for wall trenches, foundation, top surface of plinth filling, foundation of wall and floor, along the external perimeter of the building, including drilling and plugging holes etc. complete conforming to manufacturers specification and as directed by the Engineer-in-Charge. (Plinth area only to be measured for the payment ) (The above work shall be carriedout by an agency having sufficient experience and should ensure a warranty for a period of 5 years. Only skilled and experienced persons shall be employed for this purpose.)The rate shall include cost, conveyance,lead, lift of all materials, labour etc. complete as per direction of Engineer-in-charge.

Providing and laying 5mm thick tile protection sheet of approved make ( a closed cell, polymer based micro cellular foam, reinforced with high performance polymerson finished) vitrified tile/engineered stone/ granite tile/slab /vinyl and other flooring for protection and removal of the same after completion of all other works ,including cost and conveyance of all materials, labour charges,lead, lift, till handover etc, complete as directed by Engineer-in-Charge at all levels.Each sheet shall be laid with a minimum overlap of 5cm and if damaged ,replace with new sheet as directed by Engineer-in-Charge without any additional cost.

(SH: - 8.0 - CEILING SYSTEMS)- Baffle ceiling Aluminium, U-Baffle (50mm x 50mm) False Ceiling and vertical wall cladding Supplying and fixing Interior Aluminium Baffle Ceiling and vertical wall cladding of approved RAL colour consisting of U-Shaped Profiles 50mm wide x 5 thick Aluminium Alloy 3105 with inwardly returned edges of 6 -9mm. The baffle shall be manufactured on high speed, high precision roll forming machine with Hi configuration roller levelling process to ensure the flatness and to avoid the failure of metal at corners which may occur normally on press brake machine. Panels to be pre-treated inhouse with latest nano technology process and electro statically powder coated with automatic Carona system and cured with gas catalytic technology for good bonding and high coating strength. Baffles are fixed to the proprietary Baffle Carrier system made of double baked enamelled Aluminium alloy 3105/3005 with cut outs to hold the panels in a module of 150mm in black colour & Distance between 2 baffles shall be 150mm C/C. Baffle Carrier shall be fixed at a distance of 1.2mtrs to 1.5mtrs c/c suspended by means of G.I. Threaded Rod of 6mm diameter at a distance of 1.2mtr to 1.5mtrs c/c. The Interior system shall be supported to wall with HDI proprietary fixing system with help of mullions made out of 1.2mm thick G panels of required length shall be fixed on mullion profile in module of 150mm The mullion profile shall be fixed at 150 mm from panel ends and at a distance of maximum 1200 mm center to center across panel span. The mullion profile shall be fixed to a Wall/concrete structure/MS structure by means of fasteners. . The purchase price( excluding GST) for baffle ceiling tiles and suspension system should be taken as Rs 6550/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The rate shall include cost, conveyance,lead, lift of all materials, labour, scaffolding charges, painting etc. complete as per drawings, specifications and direction of Engineer-in-charge. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for proper installation, material composition & quality performance of both ceiling panels and supporting system for a period of 10 years from the date of completion of the said work. The measurement shall be taken along the girth on the bottom side of the ceilings, in square meters.The structural steel work required for this work will be paid in the respective item seperately.

Aluminium metal strip ceiling Design,Supply & Installation of Aluminium plain/wood grain finish Strip ceiling system at all levels for external /internal application complies with IS 875 part 3 1987 on wind loading, the same should be tested for and complying to a wind load resistance of minimum 1.2 kpa (as tested by an independent and competent authority) as per prevalent and in practice wind loading norms and procedures. The system consists of strip panel size 300mm X 3000mm and mimimum 30mm deep with bevel / square edge manufactured out of 0.7mm thick or above stove enameled coil coated on continuous paint line/ polyster powder coated and double baked, roll formed from corrossion resistant aluminum alloy AA3005/3003/3105, according to ASTM C635, ASTM E1264, EN 13964 and quality standards of TAIM e. V : latest version or equivalent standards and thickness according to static requirements. The system shall be perfectly levelled, aligned at desired height in plain, curved and vertical face in accordance with the false ceiling pattern as per drawing and the system shall be installed. Panels shall be formed with tiling upward bending at both sides and further inward bending flange on two side for clipping onto the proprietary modular carriers. The suspension system consists of clip -in profile shaped special secondary profile of 1 mm thick black coated galvanized steel of 5mtrs of suitable size, shape and strength shall be used to support the strip panel up to 3 meter, positioned at maximum 150mm distance from both ends of the panel and inbetween at a maximum distance of 750mm c/c. Connecting clips or nuts/bolts of galvanized steel is used to connect primary and secondary profiles. The profile suspension clip of galvanized steel to join the primary angle to threaded suspension rod of 8mm with ceiling brackets and necessary fasteners/ Panel shall be clipped to a baked enamelled Aluminium carrier of 41.5 mm wide x 62 mm deep x 0.95 mm thick in standard length of 5 mtrs, positioned at maximum 150 mm distance from both ends of the panels and in between at maximum distance of 750mm c/c. Panel carrier shall be fixed by means of M8 nut bolts at 550 mm c/c to the suitable substructure provided by others or equivalent, in accordance with Manufacture's specifications and directions of the Engineer-in-Charge.The panels shall be individually locked with the provision available in the panel carrier. The system shall be installed in line and level and as approved by Engineer-in-Charge. The threaded rod will be suspended from the slab/purlins/ substructure with necessary fasteners with expansion bolts at 1200mm c/c maximum and the primary profile spaced at 1200mm c/c maximum and secondary profile spaced at 750mm c/c maximum. The strip panels shall be inserted on the clip-in profile carrier. The panel should be rolled formed with square / bevelled edges decided as per the site mock up and instructions of Engineer-in-Charge. The aluminium strip panels shall be weather - fast, dirt retending and scratch resistant of 0.7mm thickness or above shall be polyster powder coated on continuous paint line with minimum 80 microns/stove enamelled coil coated with minimum of 30 microns with 20% gloss with premium plain colour or wood finishes. The suspension system consisting of carrier, hanger, threaded rod, perimeter profile/ edge trim, security clips etc. shall be provided in accordance with approved Manufacture's standard specification and directions of Engineer-in-Charge. The suspension system shall be consists of secondary carrier 1mm thick galvanized steel, primary L carrier 30x30x2mm galvanized steel and hanger 20x70x2mm threaded rod 8mm, C shaped perimeter profile 20x40x20mm and 0.7mm thick edge profile or equivalent, in accordance with Manufacture's specifications and directions of the Engineer-in-Charge. Edge profile and perimetre profile shall be of prepainted Aluminium and color matching with the strip panels etc. Ceiling termination, edge trim shall be as approved by Engineer-in-Charge.The rate shall also include the cost of making openings of any shape and fixing of light fittings, grills, diffusers,smoke extractor fan openings, Air terminal devices for HVAC, cut-outs etc. made with frame of perimeter channels including wall trim/edge trim and infinity profiles of 300 mm width to create perimeter encloser, interface carrier for other materials as per drawing and finishing the edges as directed by Engineer-in-Charge. The purchase price( excluding GST) for ceiling tiles and suspension system should be taken as Rs 3975/sqm. and any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor.The rate shall include cost, conveyance,lead, lift of all materials, labour, scaffolding charges, clearing all refuse, rubbish, etc. complete as per drawings, specifications and direction of Engineer-in-Charge. Contractor should submit detailed design and corresponding calculations of design of all structural suspension system of metal false ceiling, structural steel support and shop drawings vetted by the consultant in accordance with design parameters specified by the Consultant and the codal requirements of BIS (Bureau of Indian Standards) latest version, all relevant safety codes, National Building Code and DIN ISO 9001, LEED & DGNB, EN 13964 , EN 13501-1 building material class A2-s1, d0 Class A tested to ASTM E 84 class 0 tested to BS 476 part 6/7, E DIN EN ISO 354 , ASTM C 423 etc to the Engineer-in-Charge/Consultant. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for proper installation, material composition & quality performance of both ceiling panels and supporting system for a period of 10 years from the date of completion of the said work. The measurement shall be taken along the girth on the bottom side of the ceilings, in square meters and deductions shall be made for all openings exceeding 0.4 sqm in area.The structural steel work required for this work will be paid in the respective item seperately.

Providing and Fixing 12mm thick BWP grade ply false Ceiling with wooden struts using structural steel frame work (shall be measured and paid under relevant item)suspended from the existing slab/structure.The ply surfaces shall be finished with approved emulsion paint at back side as per direction of Engineer in charge at all levels. Ply box struts (approx.size 30x100mm)shall be provided at spacing not less than 600mm c/c in one direction with 12mm thick BWP grade ply and finished with 3.5mm thick teak wood veneer finished in PU open grains on all exposed surface (Two 12mm ply stick to make it one )as per drawing.Veneer is finished with applying 2 coat PU ceramic/glossy/matt coat, the surface suitably cleaned by using sand paper, filling of grains with wood filler and dent filler, applying approved wood stain as per the direction of Engineer-in -Charge for getting required shade, applying 2 coats of PU sealer, sanding the surface after applying PU sealer and applying 2 coats of PU ceramic/glossy/matt top coat. etc complete as per drawing . The ceiling shall be fixed to the roof soffit with adequate suspenders. The item shall be inclusive of cutting & making cutouts for lights, diffusers etc all complete.The rate is including cost and conveyance of all materials, labour charges, lead,lift,scaffolding ,fixing the all ceiling fixtures to ceiling, sundries etc complete as directed by Engineer- in-Charge at all levels.

PLAIN ALUMINIUM GRID CEILING Design, supply & Installation of plain Aluminium Lay In Tile ceilings system at all levels and consists of tile size; 600mm x 600mm x 10mm deep manufactured out of 0.7mm aluminium alloy AA3105/3003/3005, Lay-in Plain Tile False Ceiling on 15mm ‘T’ Framework of module 600mm x 600mm. Panels shall be of size 584mm x 584mm made out of 0.7mm thick Aluminium Alloy AA 3105/3003/3005. All Tiles shall be manufactured in a single stage manufacturing procedure from a die, where the notched & level sheet shall be pressed into a lay-in tile by means of a die.Tiles shall be bevelled edge.The tiles shall have a total Vertical Height of 10 mm & installed height of 10 mm including the beveled edge. The Tile shall have an outward bent lip of 7mm. The Tile shall be Powder coated in 60-80 microns/ stove enameled coil coated 20 microns in approved colour. Grid system for fixing ceiling tiles shall comprise of galvanised steel Tees precoated in G.I. caping of white colour. The 15mm main tee runners shall be suspended at an interval of 1200mm centre to centre. The 15mm cross tee runner shall be fixed at 600mm centre to centre and further supported with 15 mm cross tee at 600mm centre to centre with interlocking arrangements to form grid of 600mm x 600mm. The main tee shall be supported by means of 4mm G.I. rod and butterfly clip from slab/roof. The suspension shall be provided at 1200 to 1500mm centre to centre. The tiles shall be stove enamelled coil coated in approved colour with thickness of 25 microns/powder coated thickness of 60 to 80 microns. 'The rate shall also include the cost of making openings of any shape and fixing light fittings, grills, diffusers,smoke extractor fan openings, Air terminal devices for HVAC, cut-outs etc. made with frame of perimeter channel/ Angle including wall trim/edge trim and infinity profiles of 300 mm width wherever it is necessary to create perimeter enclosures, interface carrier for other materials as per drawing and finishing the edges as directed by Engineer-in-Charge. The rate shall include cost, conveyance,lead, lift of all materials, labour, scaffolding charges, clearing all refuse, rubbish etc. complete as per drawings, specifications and direction of Engineer-in-Charge.'Contractor should submit detailed design and corresponding calculations of design of all structural suspension system of metal false ceiling, structural steel support and shop drawings vetted by the consultant in accordance with design parameters specified by the Consultant and the codal requirements of BIS (Bureau of Indian Standards) latest version, all relevant safety codes, National Building Code and DIN ISO 9001, LEED & DGNB, EN 13964 , EN 13501-1 building material class A2-s1, d0 Class A tested to ASTM E 84 class 0 tested to BS 476 part 6/7, E DIN EN ISO 354 , ASTM C 423 etc to the Engineer-in-Charge/Consultant. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for proper installation, material composition & quality performance of both ceiling panels and supporting system for a period of 10 years from the date of completion of the said work. The measurement shall be taken along the girth on the bottom side of the ceilings, in square meters and deductions shall be made for all openings exceeding 0.4 sqm in area.

Providing and fixing suspended false ceiling at all levels, using 12.5mm Moisture resistant tapered edge gypsum board panels(conforming to IS 2095 part I:2011) which includes providing and fixing G.I Perimeter channels of size 0.50mm thick with unequal flanges of 20mm and 30mm and a web of 28mm along the perimeter of ceiling, screw fixed to brick or RCC wall /partitions with the help of nylon sleeves and screws, at 230mm centres. Then suspending G.I. Intermediate channels of size 45x15mm, 0.9mm thick suspending from slab, at all heights using angle cleats of size 25mm wide and 1.6mm thick with flanges of 27mm and 37mm at 1220mm centre to centre, one flange fixed to the ceiling with expansion bolt/metal rawl plug as per manufacturerers specification and other flange to the angle hangers of 25x10x0.5mm of required length as per drawings, specifications and direction of Engineer-in-Charge. Ceiling section of 0.5mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 457mm centres. 12.5mm moisture resistant tapered edge Gypsum board (conforming to IS-2095- part 1: 2011)is then screw fixed to ceiling section with 25mm dry wall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. The ceiling shall be fixed in line and level. The boards shall be jointed and finished to a flush finish of tapered and square edges of gypsum board (including providing V grooves in cut tiles wherever necessary )with recommended jointing compound filler ( 2 coat putty) with paper tapes, control joints and finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and finished on the bottom side with two coats of approved putty,two coats of approved primer suitable for gypsum board as per manufacturers specifications and two coats of plastic emulsion paint of approved brand and colour and two coats of approved quality water sealant on the top surface of gypsum board. The ceiling shall be provided with recessed portions/coffers/cove as per drawing. Nothing extra shall be paid for providing specified number of recesses at different levels. The vertical/slanting portion between different levels shall also be provided with12.5mm Moisture resistant gypsum board panels fixed by means of 25x10x0.5mm GI angle sections and ceiling sections as specified. The rate shall also include the cost of making openings/cutout of any shape and fixing light fittings, grills, diffusers, etc. made with frame of perimetre channels as per drawing and finishing the edges as directed by Engineer-in-Charge. Ceiling height can be upto 6m.The supporting system may be provided with additional supports, for any additional height and cost of such additional supports will be paid separately under relevent item.The cost of putty and painting shall be measured and paid under relavent item. The rate shall include cost, lead, lift of all materials, labour, scaffolding charges, painting, etc.complete as per drawings, specifications and direction of Engineer-in-Charge. The measurement shall be in square metres and deductions shall be made for all openings exceeding 0.4 sqm in area.The exposed vertical area also will be measured and paid along with horizontal area.

Supply and Installation of Exterior HPL 6mm thick Exterior grade F- Quality panels of approved make and standard size with both side décor.Exterior panels shall be high-pressure laminates (HPL) as per EN 438-6, type EDF ); Panels shall be double hardened including acrylic polyurethane resin which is thermally cured under high pressure conforming to European norms with CE Mark on each and every Panel as per EN 438-7 with proven 3rd party certification with weather protection and excellent sustainability against UV, weathering, working in Heat Resistance range of -80 to 180. Installation of Exterior panels for facades and also soffits, shall be done by approved Rivets (with Fixed and Sliding Points) with minimum recommended, Aluminum T section of 75x37x2.8 mm thick and L section 30x30x2.8mm thick held by Wall Bracket with Wind load and Dead load slot as per design, anchored by standard Hilti/Fischer or equivalent make anchor fasteners along with Thermal Separator. Installation of Exterior Panels shall be done using Rear Ventilated Principles only, which is to be ensured by providing ventilation gap minimum 200 cm2/ per Meter (for free flow of air behind the façade) for the façade and using the framework with no horizontal section.(Aluminium framework shall be measured and paid seperately).The rate shall include cost and conveyance of all materials,labour charges,lead,lift as directed by Engineer-in-Charge at all levels. The purchase price( excluding GST) of Exterior grade HPL sheets shall be taken as Rs.2691/sqm and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) in the payment making to contractor)

Providing and Fixing hard wood battens of 100*75 mm (radial type) ceiling with 6mm thick HPL using structural frame work of ISA 50x50x6mm (shall be measured and paid under relevant item)suspended from the existing slab/structure at a spacing of 1200mm C/C . Hard wood grid shall be provided over the HPL surface as per design and drawing. The surfaces of hardwood finished with sand paper, filling of grains with wood filler and dent filler,applying approved wood stain for getting required shade ,applying two coats of PU sealer, two coats of PU top coat etc complete as per direction of Engineer in charge at all levels. The ceiling shall be fixed to the roof soffit with adequate suspenders. The item shall be inclusive of cutting & making cutouts for lights, diffusers etc all complete.The rate is including cost and conveyance of all materials, labour charges, lead,lift,scaffolding at all heights (upto 7.5m height) ,fixing the lighting to roof,PU finish , sundries etc complete as directed by Engineer- in-Charge at all levels.wooden plank (radial type) ceiling. Only the exposed finish surface area without projections of batterns shall be measured for payment.

Providing and fixing plaster of paris moulding/cornices of section size 100x100mm (overall dimensions) as per drawing, fixing to the ceiling/walls at all heights using brass screws. The plaster of paris shall be of approved make and the sections shall be made using coir/fibrous reinforcement. The rate shall include cost of all materials, labour charges, moulding charges, scaffolding charges, painting two coats of plastic emulsion over two coats of approved primer etc. complete as directed by Engineer-in-charge.

(SH:- 9 :- CLADDING & PARTITION WORKS) Providing & fixing 9 mm thick BWP grade ply confirming to IS- 710 on existing Aluminum frame work for column , wall cladding etc using approved size screws at every 600 mm center to center at all levels as per drawing.The ply shall be fixed in correct line and level as per drawing and as directed by the Engineer in charge. The rate shall include the cost & conveyance of all materials, labour charges,levelling, lead, lift , cutting any shapes , provisions for electrical, networking fixtures wherever required, etc complete as directed by Engineer in Charge at all levels.

Providing & fixing 9 mm thick fire retardant ply confirming to IS-5509 on existing Aluminum frame work for column , wall cladding etc using approved size screws at every 600 mm center to center at all levels as per drawing.The ply shall be fixed in correct line and level as per drawing and as directed by the Engineer in charge. The rate shall include the cost & conveyance of all materials, labour charges,levelling, lead, lift , cutting any shapes , provisions for electrical, networking fixtures wherever required, etc complete as directed by Engineer in Charge at all levels.

Providing & fixing laminate panelling with one side decorative and other side balancing lamination, formed out of 1mm thick decorative high pressure laminated sheet of approved finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, on 12mm thick BWP grade plywood (factory pressed) fixed on existing frame work using approved size screws. The rate shall includes cost and conveyance of all materials, labour charges, lead, lift ,provision for fixing all electrical, networking boxes in the panelling ,cutting and making good the wall/floor etc wherever required at required heights/levels as directed by Engineer in Charge at all levels.(The base price considered for 1mm thick laminated is Rs. 1765/sq.m( excluding GST)and any deviation plus or minus in the purchase price in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor) .Laminate panelling with brass lining as per the drawing and direction of engineer in charge.

Providing & fixing 15 cm wide, 8 mm thick cement fibre board panels(Exterior grade) prefinished as wooden planks to sunshade roof soffit/wooden planks to existing wall/cement board of existing terminal building, to a height upto 24m as per approved design, using adequate Aluminium framework, brass screws and additional adhesive for extra caution and finishing the screw heads to match the same wooden finish and colour of the cement panel with putty and paint / powder coating. Cement fibre board shall be pre finished to the required wooden texture finish . Necessary expansion gap to be provided during the installation of pre finished cement fibre board as per manufactures specification .( structural / Aluminium frame work will be measured and paid seperately) The rate shall include cost and conveyance of all materials, labour, scaffolding, lead, lift etc complete at all levels as directed by the Engineer- in-Charge

Providing & fixing 8mm thick(exterior grade) cement fibre board panels in required profile over existing wall/ cement fibre board/ Aluminium frame work to a height upto 16 m using brass screws and additional adhesive for extra caution. ( Aluminium frame work will be measured and paid seperately under relavent items ) .Cement fibre board shall be finished with 2 or more coats of emulsion paint of approved shade over 2 coats of cement primer .Screw heads shall match the same finish and colour of the board with putty and paint / powder coating. The rate shall include cost and conveyance of all materials, labour, scaffolding, lead, lift etc complete at all levels as directed by the Engineer- in-Charge .

Providing & fixing upto 10cm wide, 8mm thick beadings using cement fibre board panels (Exterior grade )over existing wall/ cement board to a height upto 15 m, using brass screws and additional adhesive for extra caution. Beading shall be finished with 2 or more coats of emulsion paint of approved shade over 2 coats of cement primer .Screw heads shall match the same finish and colour of the board with putty and paint / powder coating. The rate shall include cost and conveyance of all materials, labour, scaffolding, lead, lift etc complete at all levels as directed by the Engineer- in-Charge .

Providing & fixing 5 cm wide, 8mm thick beadings using cement fibre board panels (Exterior grade) over existing wall/ cement board to a height upto 16 m, using brass screws and additional adhesive for extra caution. Beading shall be finished with 2 or more coats of emulsion paint of approved shade over 2 coats of cement primer .Screw heads shall match the same finish and colour of the board with putty and paint / powder coating. The rate shall include cost and conveyance of all materials, labour, scaffolding, lead, lift etc complete at all levels as directed by the Engineer- in-Charge.

Providing and fixing 18mm thick exterior grade UPVC board as roof face board (Mughappu) with Multiwood of approved make , at a height of 20 m, made of U Pvc polyester resin in an extruded polymer profile form with CNC cutting as per approved design and drawing.The board shall be 100% waterproof, Termite & Borer proof, corrosion free & fire retardend and used for wet area applications.The rate shall include cost and conveyance of all materials,approved PU finishing, labour, scaffolding, lead, lift etc complete at all levels as directed by the Engineer- in-Charge. The structural steel for the support shall be measured and paid seperately.

Supply and Installation of Exterior HPL 6mm thick Exterior grade F- Quality panels of approved make and standard size with both side décor.Exterior panels shall be high-pressure laminates (HPL) as per EN 438-6, type EDF ); Panels shall be double hardened including acrylic polyurethane resin which is thermally cured under high pressure conforming to European norms with CE Mark on each and every Panel as per EN 438-7 with proven 3rd party certification with weather protection and excellent sustainability against UV, weathering, working in Heat Resistance range of -80 to 180. Installation of Exterior panels for facades and also soffits, shall be done by approved Rivets (with Fixed and Sliding Points) with minimum recommended, Aluminum T section of 75x37x2.8 mm thick and L section 30x30x2.8mm thick held by Wall Bracket with Wind load and Dead load slot as per design, anchored by standard Hilti/Fischer or equivalent make anchor fasteners along with Thermal Separator. Installation of Exterior Panels shall be done using Rear Ventilated Principles only, which is to be ensured by providing ventilation gap minimum 200 cm2/ per Meter (for free flow of air behind the façade) for the façade and using the framework with no horizontal section.(Aluminium framework shall be measured and paid seperately).The rate shall include cost and conveyance of all materials,Scaffoldings,labour charges,lead,lift as directed by Engineer-in-Charge at all levels. The purchase price( excluding GST) of Exterior grade HPL sheets shall be taken as Rs.2691/sqm and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) in the payment making to contractor)

Supply & Installation of non reflective glass film of approved make with U value 1.14, visible light trasmittance 50%,glare reduction 45% and total solar energy rejection 31%. The film shall install with self-adhesive and bubble-free installation on clean glass .The rate shall include the cost and conveyance of all materials, labour charges, scaffolding, lead,lift,sundries,removing the existing glass film thorough cleaning of surface etc complete at all levels as directed by the Engineer-in-Charge . The above work shall be carried out by an agency having sufficient experience in concerned work and architectural warranty shall be ensured for any defective installation and material for a period of 10 years from the date of completion of the said work .Only skilled and experienced persons shall be employed for this purpose. The purchase price( excluding GST) of film shall be taken as Rs.500/sqm and any deviation plus or minus in the purchase price( excluding GST) will be adjusted(paid extra or deducted) in the payment making to contractor)

Providing wood work in frames of mouldings,cornices,beadings, panellings,column capitals,special architectural/ ornamental wooden works etc with engraved designs and fixing in position with wooden adhesive of approved quality and screws / nails. as per approved design and drawings and the same shall be fixed on existing MS/Aluminium framework to proper line & level including cost and conveyance of all materials, labour charges,lead,lift ,etc complete at all levels as directed by Engineer in Charge-Using second class teakwood

Providing & fixing jalli work for cladding with 3.5mm thick veneer on 9 mm thick BWP ply with necessary aluminium frame work.Finishing of veneer to be done by approved shade of PU ceramic coat , as per the direction of Engineer-in -Charge and as per drawing after being punctured by laser/CNC machines for 3D carving . The rate shall includes cost and conveyance of all materials, Design and Lazer Cutting/CNC cutting with 3D carving and PU finish , labour charges,lead,lift , adhesives ,screws, scaffolding etc. complete as directed by Engineer in Charge at all levels. Elevational area to be measured for payment

PARTITIONS Providing & fixing Glass panelling with 6 mm thick Lacquered toughened colour glass using adhesive for column, partitions and wall cladding at all levels over existing 9 mm thick BWP grade ply backing and frame work .Mirror-compatible adhesive or double-sided adhesive tape must be used. The rate shall include cost and conveyance of all materials, 5 mm Aluminium channel for the glass joints, labour charges, lead, lift, scaffolding, etc complete as per drawing and as directed by Engineer in Charge at all levels.(The base price considered for lacquered Glass is Rs. 2853/sq.m inclusive of all taxes and any deviation plus or minus in the purchase price in approved shade will be adjusted(paid extra or deducted) while making payment to the contractor)

Providing & fixing wood skirting using approved hard wood,with PU ceramic coat, the surface suitably cleaned by using sand paper, Filling of grains with Wood Filler and Dent Filler,Applying Approved Wood Stain as per the direction of Engineer-in -Charge for getting required shade ,Applying 2 Coats of PU Sealer ,sanding the surface after applying PU sealer and Applying 2 Coats of PU Top coat.complete as per the technical specification of manufacturer and design as per drawing and fixed over masonry wall /opaque partition to proper line & level. The skirting shall be fixed with SS screw /approved adhesives. The rate includes cost and conveyance of all materials, labour lead, lift,etc.complete as per drawing,and as directed by the Engineer in charge at all levels.

Hard wood skirting 30cm height 15mm thick

Hard wood skirting 15cm height 15mm thick

Providing and fixing 3.5mm thick veneer cladding on walls ,columns. Beams with 9mm thick BWP ply conforming to IS 1328 BWP grade and applying 2 coat PU ceramic coat, the surface suitably cleaned by using sand paper, filling of grains with wood filler and dent filler,applying approved wood stain as per the direction of Engineer-in -Charge for getting required shade ,applying 2 coats of PU sealer ,sanding the surface after applying PU sealer and applying 2 coats of PU ceramic matt top coat. etc complete as per drawing . The rate shall includes cost and conveyance of all materials, labour charges,lead,lift , adhesives ,screws,opening for fixtures, PU ceramic coat,scaffolding etc. complete as directed by Engineer in Charge at all levels.

Providing and fixing Teak wood lipping / moulded beading of below mentioned size fixed with wooden adhesive of approved quality and screws / nails on the edges of the pre-laminated partition work and PU finish on exposed surface ,the surface suitably cleaned by using sand paper, Filling of grains with wood filler and dent filler, applying approved wood stain as per the direction of Engineer-in -Charge for getting required shade, applying 2 coats of PU Sealer ,sanding the surface after applying PU sealer and applying 2 Coats of PU top coat complete as per the technical specification of manufacturer. The rate shall includes cost and conveyance of all materials, labour charges, lead, lift , PU finish etc complete as per direction of Engineer-in-Charge.

Teak wood beeding 50x50mm

Teak wood bedding 100x25 mm

Providing and fixing 17.53 mm laminated toughened clear glass( 8mm toughened glass+1.53PVB+8 mm toughened glass) with approved framework for top and bottom channels, verticals whereever it touches masonry/partition as per manufacturers specification .The top channel is supported till the original ceiling using adequate MS framework and the bottom and side channels are strongly anchored to the floor/wall using chemical anchor fasteners with option for installing glass to glass joint with silicone or other required accessories from FFL to 3000mm as per the drawing and technical specification .The rate shall includes cost and conveyance of all materials, labour charges, lead, lift, ,all fixing arrangement and making necessary holes etc for fixing required fittings, all complete etc complete as directed by Engineer-in-Charge.All toughened Glass shall be heat soaked.

Supply & Installation of casted films 0.38mmthick of approved make Crystal Collection with approved art work digitally reproduced with water-based inks certified to have no hazardous air pollutants. The film shall install with self-adhesive and bubble-free installation to be done on clean glass .The rate shall include the cost and conveyance of all materials, labour charges, scaffolding, lead,lift,sundries etc complete as directed by the Engineer in charge at all levels. The above work shall be carried out by an agency having sufficient experience in concerned work and should have certificate of image license and architectural warranty ensure for any defective installation and material for a period of 3 years from the date of completion of the said work .only skilled and experienced persons shall be employed for this purpose. The face area of the film before installation shall be taken for payment.(The base price considered for casted films is Rs. 1740 /sqm (excluding GST)and any deviation plus or minus in the purchase price in approved shade will be adjusted (paid extra or deducted) in the payment making to contractor)

Providing and fixing of Factory Finished Printed Fabric in line and level and in approved pattern as per drawing, inclusive of. Fabric shall be wrapped on the ply and shall be stretched uniformly along the direction of weave and shall be wrinkle free and all edges to be finished complete and as directed by Engineer in charge. basic price for the fabric considered is 2690/sqm(excluding GST)and any deviation plus or minus in the purchase price in approved shade will be adjusted (paid extra or deducted) in the payment making to contractor)

Supply and fixing mirror collage cladding with 5mm thick bronze mirror (Curve edge including cutting and polishing edges) on 9mm thick BWP grade ply backing using suitable glass silicone adhesive as recommended by the manufacturer as per drawing for a height upto 4m.The rate includes cost and conveyance of all materials,wastage, labour, lead, lift,scaffoldings etc. complete as per the Engineer-in-Charge at all levels. (The purchase price ( excluding GST)considered for the mirror collage cladding including Curve edge cutting and polishing edges as per the dimension in drawing is Rs. 13000/sqm ( excluding GST) and any deviation plus or minus in the purchase price in approved shade will be adjusted(paid extra or deducted) in the payment making to contractor)

Supply and fixing tinted mirror wall cladding with 5mm thick bronze mirror on 9mm thick BWP grade ply backing using suitable glass silicone adhesive as recommended by the manufacturer as per drawing and technical specification for a height upto 5m.The rate includes cost and conveyance of all materials,wastage, labour, lead, lift,scaffoldings etc. complete as per the Engineer-in-Charge at all levels. (The purchase price ( excluding GST)considered for the tinted mirror wall cladding including polishing and edges finishes as per the dimension in drawing is Rs. 14000/sqm ( excluding GST) and any deviation plus or minus in the purchase price in approved shade will be adjusted(paid extra or deducted) in the payment making to contractor)

Providing & fixing 1mm thick approved SS 316 grade skirting(copper finish) over 6 mm thick BWP grade ply which is fixed over masonry wall /RCC/opaque partition to proper line & level . The installed skirting shall be provided with approved matching colour angle,bands, without exposed fixing bolts and without any dirt traps.The rate shall includes cost and conveyance of all materials,6mm ply,labour charges, lead, lift ,scaffolding,etc complete as per manufacturer's specification, installation guidelines & instructions of the Engineer in charge at all levels.

Providing & fixing laminate conforming to IS:2046-1995 of 1mm thickness over existing ply work for column and wall cladding using adhesives as per drawing .The rate shall include cost and conveyance of all materials,cutting , making patterns, labour charges, lead, lift ,scaffolding,etc complete as per drawing and as directed by Engineer in Charge at all levels.(The purchase price ( excluding GST)considered for 1 mm thick laminate is Rs. 1765/sqm ( excluding GST) and any deviation plus or minus in the purchase price in approved shade will be adjusted(paid extra or deducted) in the payment making to contractor)

Supply & Installation of framed modular Glass Partition System (height upto 3600mm) using 17.53 thick toughened heat soaked glass ( 8mm toughenned+1.53 PVB +8mm toughened glass) with proprietary Slimline aluminium framework for top and bottom channels, verticals whereever it touches masonry/partition as per manufacturers specification .The top channel is supported till the original ceiling using adequate MS framework and the bottom and side channels are strongly anchored to the floor/wall using chemical anchor fasteners with option for installing glass to glass joint with silicone or other required accessories from FFL to 3600mm as per the drawing and technical specification. Aluminium frame work to be anodised finish and shall be designed for minimum 6000mm spacing between two verticals . toughned glass shall be heat soaked.The glass joint shall be butt and finished with non staining silicon sealent as approved by Engineer-in-charge. The samples of the profile is to be approved from Engineer-in-charges. The rate shall be inclusive of cost of all materials, transportation, loading - unloading charges, lead, lift, labour charges etc complete as directed by the Engineer-In-Charge.

Providing and fixing wardrobe unit of size 600x1250 mm in plan and of height 3000mm using carcass built of 19mmthk BWP grade ply with 1mm thk laminate finish inside and outside. Shutters are provided with bronze mirror inlay and fixed to carcass by means of sleek sliding channel mechanism of approved make and model. The unit is provided with open racks as per design. All ply edges touching the ground or left open is provided with wooden lipping/ edge band to match colour.The rate shall include cost and conveyance of all materials,labour charges,lead,lift etc complete at all levels as directed by the Engineer-in-Charge

Supply & installation of Clay ventilated façade system teracotta finish for external wall cladding – Clay tiles size of 600 x 300 x 20mm thickness fixed in Horizontal fixing system , with 50mm x 50mm box sections as vertical member and special C profiles fixed horizontally and the tiles fixed with Clips on the C Profile and every vertical is fixed with W joint profile which acts as rain drain of the system (As perthe approved drawings)Clay tiles with Density of 2 – 2.4 g/cm3 and with bending strength of > 15 MPa.The rate shall include cost and conveyance of all materials,labour charges,lead,lift etc complete at all levels as directed by the Engineer-in-Charge

Providing and fixing G.I. mesh of required width in mesh size 25x25 mm made of G.I wire of dia 6 mm with appropriate structural frame work (paid extra) with primer and painting etc complete ,labour charges,lead,lift etc at all levels as per the direction of Engineer - in- Charge.

Supply and installation of HPL jalli work sandwitched with acrylic based sheet over 9mm thick BWP grade ply with necessary aluminium frame work. The rate shall include cost of all the materialas, conveyance labour, design and lazer cutting/CNC cutting with 3D carving adhessive,screws,scaffolding etc complete as per the drawings and as per the direction of engineer in charge at all levels Elevational area to be measured for payment

Providing and fixing DB box with door in line and level using 19mm thick fire rated grade ply confirming to IS-5509 up to a depth of 150mm. The door shutter shall be fixed with zero crank hydraulic hinges to the ply carcass.DB door shall be provided with push open system for openings.The rate shall include the cost & conveyance of all materials, zero crank hydraulic hinges,push open system, labour charges, lead, lift , cutting any holes for conduits ,all fixtures wherever required, etc complete as directed by Engineer in Charge at all levels.Elevational area of door to be measured for payment.

Providing and fixing insulation with Resin Bonded rock wool conforming to IS: 8183, having density 49 Kg/m3, 50mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall/partition system with screw, rowel plug & washers and held and in position by criss crossing GI wire etc. complete as per directions of Engineer-in-charge.

(SH:- 10- LANDSCAPING WORKS) Design, Supplying and laying synthetic turfing as per design and drawing with special grade imported polyethylene blade having pile height :35 mm,Density:16800 stitches/m2 of approved make(Green mead or equivalent )over stabilised soil bed .The turfing should be multi coloured green grass blades enhancing the natural appearance and realistic look with UV resistant, non toxic, non flamable, chlorine resistant and 100% recyclable .The backing of turf should be with Polypropylene and net cloth as per manufacturers specification. The rate shall include the cost and conveyance of all materials, labour charges, lead, lift, preparation of surface etc. complete as directed by Engineer in Charge at all levels and should ensure a guarantee for a period of 8 years.(The base price considered for synthetic turf is Rs.1280 /sqm excluding GST and any deviation plus or minus in the purchase price will be adjusted(paid extra or deducted) while making payment to the contractor).

(SH:- 11- ROOFING WORKS) Supply and fixing of colour coated Manglore steptile profile 0.45 mm Base Metal Thickness(BMT), (0.50mm TCT, 0.53mm TPT) Profiles a nominal 1000 mm wide coverage profile with nominal 28 mm rib height of nominal 200 mm centre-to-centre pitch length. The profile step length is 200mm with height of 16 mm, having interlock arrangement to make it leak proof. The steel sheet is having high tensile sheet G300 (Fy=300Mpa), metallic coated with Zinc-Aluminium alloy (i.e. 55% Al, 43.4% Zinc, 1.6% Si -Zincalume), AZ150 (min 150 gm/m2 total on both side), pre-painted with Super Durable Polyester Colorbond XRW qualitypaint includes inorganicinfrared reflective pigment (High SRI-”Thermatech technology”) of 20μm exterior coat on top surface and 5μm reverse coat on back surface over 5μm primer coat on both surfaces of approved color shade by concern authority. The sheet conforms to general requirement of AS/NZS 2728 type 4 / IS 15965 class 3 durability and gloss value of 25% -40%of approved make. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material.Roofing sheets shall be crest fixed to the purlin with hot dip galvanized imported self drilling fasteners with integral EPDM washers for perfect sealing . Rate shall including cost and conveyance of all material, including all accessories, lead, lift, scaffolding, labour charges etc. complete at all levels as directed by Engineer-in -Charge. For roof measurements, area shall be measured as laid from roof edge to edge. No deduction shall be made for openings after installation. (The above work is to be carried out by a specialized agency approved by the Manufacturer and Engineer-in-Charge having experience in the laying of this type of roofing system.)

Providing & fixing on roof pressed clay tile (Mangalore tile) of size 320mm or nearest with Class AA Mangalore pattern tiles of approved make and as per approved pattern on steel frame work complete (steel frame work to be paid separately) including the cost, conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer-in-Charge at all levels(The purchase price considered for MP tile is Rs.55/- per tile and any deviation plus or minus in the purchase price will be adjusted in the price quoted. All tiles of every three layers shall be properly tied with binding wire

Providing and laying MP hip and ridge tiles with class AA Mangalore pattern tiles of approved make including fixing with cement mortar 1:2 (1 cement : 2 coarse sand ) as directed by Engineer-in-Charge at all levels. (The purchase price considered for MP tile is Rs80/- per tile and any deviation plus or minus in the purchase price will be adjusted in the price quoted).All tiles of every three layers shall be properly tied with binding wire

Providing and laying MP tiles of size 320mm or nearest with Class AA Mangalore pattern tiles of approved make over the cement mortar reeper bands already done to correct lines and levels including the cost, conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer-in-Charge at all levels.(cost of cement mortar reeper bands will be paid seperately)(The purchase price considered for MP tile is Rs.55/- per tile and any deviation plus or minus in the purchase price will be adjusted in the price quoted).

Providing and laying MP hip and ridge tiles with class AA Mangalore pattern tiles of approved make including fixing with cement mortar 1:2 (1 cement : 2 coarse sand ) as directed by Engineer-in-Charge at all levels. (The purchase price considered for MP tile is Rs.80/- per tile and any deviation plus or minus in the purchase price will be adjusted in the price quoted).

Supply and instillation of rain water gutter at roof level encompasing existing RCC gutter using 1 mm thick SS 304 grade Stainless steel sheets including finishing joints with tig argon welding as approved by the Enginner in Charge.The gutter shall be supported on MS brackets and M.S brackets shall be measured and paid under relevant item. Gutter shall receive the downspouts at designed intervals and all joints with downspouts should be welded and made water tight . Gutter shall be fixed in lines and levels including cost and conveyance of all materials,labour charges, scaffolding, etc complete as directed by the Engineer in charge at all levels. Measurement shall be in sqm for laid width and length of Stainless steel sheet. Note:Watertightness shall be ensured by ponding water for 7 days and got approval from Engineer in charge.

Supply and fixing of Acoustic Insulation at the bottom side of the existing roofing sheet of 25mm thickness of Elastomeric Rubber Insulation manufactured as per ASTM E 84 test & which should also meet NFPA 90A supplementary materials for air distribution system which shouldnot absorbs less 0.2% water by volume (ASTM c 209), should not support microbial growth (ASTM C1071, G21, G22) and should emit objectionableodors (ASTM C 665) and should have thermal conductivity of 0.27 ( R - 2.78thermal conductivity of 0.27 ( R - 2.78in 3.4" thickness) and water vapourpresence of 0.10. - Class "1" Material- 25mm thick.- etc. Complete in all respects as per technical specifications without any damage to adjoining structures and including cost and conveyance of all materials, labour charges, lead, lift, clearing debris, all complete as specified and as directed by the Engineer-in-Charge at all levels. The above work shall be carried out by an agency having sufficient experience and only skilled and experienced persons shall be employed for this purpose

Fixing of departmentally supplied roofing sheet for temporary fencing around the site premise maintaining the proper line and level on steel frame work for barricading. ( steel work shall be measured and paid seperately) Rate shall including cost and conveyance of all material, including all accessories, lead, lift, scaffolding, labour charges etc. complete at all levels as directed by Engineer-in -Charge.

Plastering the surface of sloping roof slabs, troweling to perfect smoothness closing all the voids with CM 1:3 (1 cement, 3 sand) 12mm thick one coat including forming reeper bands of 5cmx2.5cm over the plastered surface simultaneously to the spacing of 320mm (or nearest size of MP tiles) with CM 1:3 (1 cement and 3 sand) including cost and conveyance of all materials,labour charges, curing,scaffolding charges etc. as directed by Engineer- in- charge at all levels.

Supplying and fixing HDPE bird proof net of 1.9 sqcm for the mugappu area at all levels .including cost and conveyance of all materials,labour charges, curing,scaffolding charges etc. as directed by Engineer- in- charge at all levels. (The purchase price considered for this item is Rs.490/- per sqm and any deviation plus or minus in the purchase price will be adjusted in the price quoted).

(SH: - 12.0 - FINISHING WORK) 6 mm cement plaster to ceiling of mix 1:3 (1 Cement : 3 fine sand) including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

12mm cement plaster of mix 1:4 (1 cement : 4 fine sand)including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

15mm cement plaster of mix 1:4 (1 cement : 4 fine sand)including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

15mm cement plaster of mix, 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement 2 kg/sqm including mixing water proofing material in separately) proportion recommended by manufacturer over roof at all heights including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. (water proofing liquid will be paid separately)

Extra for plastering exterior walls of height more than 10m from GL for every additional height of 3m or part thereof including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Applying one coat of water thinnable cement primer of approved brand and manufacture on all surface including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels.

Providing and applying two coat cement based putty approved brand, over the plastered wall surface (interior and exterior area) to prepare the surface even and smooth, including cost and conveyance of all materials, labour charges, lead,lift,scaffolding, sanding and cleaning the surface , sundries etc complete as directed by Engineer-in-Charge at all levels.

Providing and applying wall painting with approved make silicon based water repellent weather proof(high sheen and dirt repellent,antifungal,damp resistant & high durable )to give an even shade to New work ,Two or more coats over the priming coat(measured and paid separately) of approved primer including cost and conveyance of all materials, labour charges, scaffolding, lead,lift ,sundries etc complete as per manufactures specification and as directed by the Engineer in charge at all levels.The contractor shall ensure warranty for a period of 5 years from the date of completion of the said work.

Wall painting with luxury acrylic emulsion paint of interior grade,antifungal & anti bacterial and scratch & stain resistant of approved brand and manufacture to give an even shade on new work Two or more coats over the priming coat(measured and paid separately), for even shade and colour, luxurious high sheen finish and washable emulsion including cost and conveyance of all materials, labour charges, scaffolding, lead,lift,sundries ,etc complete as directed by Engineer-in-Charge at all levels.

Providing and applying acrylic texture finish of required pattern & shade over priming coat(measured and paid separately) on new work including cost and conveyance of all materials, labour charges, lead,lift,scaffolding, cleaning the surface ,sundries etc complete as directed by Engineer-in-Charge at all levels. (The purchase price ( excluding GST)considered for texture paint is Rs. 1060/sqm ( excluding GST) and any deviation plus or minus in the purchase price in approved shade / texture will be adjusted (paid extra or deducted) while making payment to the contractor) .

Providing and applying wall painting with approved make silicon based water repellent weather proof(high sheen and dirt repellent,antifungal,damp resistant & high durable )to give an even shade to New work ,Two or more coats over the priming coat(measured and paid separately) of approved primer including cost and conveyance of all materials, labour charges, scaffolding, lead,lift ,sundries etc complete as per manufactures specification and as directed by the Engineer in charge at all levels.The contractor shall ensure warranty for a period of 5 years from the date of completion of the said work.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls and cost of l;atex based bonding agent @ 1kg for 10Kg cement etc complete, including disposal of rubbish to the dumping ground within 50 meters lead:With cement mortar 1:4 ( 1 cement : fine sand)

Providing and applying 12mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Providing and applying plaster of Paris putty of newly constructed surface or existing surface averegae thickness of 9mm and finished in proper line and level.

Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces in Two Coats

Wall painting in two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Providing and applying two coats of exterior putty , one coat of primer for aqua fresh and two coats of aquafresh exterior paint including cost of all materials .labours, conveyance, scaffolding etc complete as directed by engineer in charge

Applying one coat of alkaline resistant cement primer of approved brand and manufacture on wall surface including cost and conveyance of all materials, labour charges, lead, lift, scaffolding, sundries etc complete at all levels as directed by Engineer-in-Charge.

Providing and applying two or more coats PU finish( Matt, semi glossy, glossy )to give a smooth finish on wood/ply/veneer work over two coats of PU sealer. The surface is suitably cleaned using sand paper, filling of grains with wood filler and dent filler, applying approved wood stain as per the direction of Engineer-in -Charge for getting required shade ,applying 2 coats of PU sealer ,sanding the surface after applying PU sealer and applying 2 coats of PU top coat complete as per the technical specification of manufacturer and as directed by Engineer-in-Charge. The rate shall includes the cost and conveyance of all materials, labour charges, lead, lift etc complete as directed by Engineer-in-Charge at all levels.

(SH:-13.0- WATER PROOFING WORKS) Providing and applying 2 coats two component acrylic polymer modified elastomeric cementitious water proof coating on roof slab , gutter ,OHT,inside of trenches,basement floors,lift pit etc.. etc which shall be mixed as per manufacture's technical specification, after thoroughly cleaning the surface by mechanical means to making it free of any loose mortar,unsound substrate,"V" grooves cut along the construction joints, cracks and joints of slab/wall on the external face and the same shall be filled with polymermodified mortar( CM 1:3 mixed with approved water proofing compound in the proportion recommended by the manufacturers), cracks in the slab (if any), pressure grouting wherever necessary by injecting mixed with approved expanding agent using pressure grouting pump with a pressure of 3 to 4kg/sqm ,strictly maintaining the coverage specified by the manufacturer, including cost and conveyance of all materials,labour charges etc complete as directed by the Engineer-in-Charge. (The above work shall be carried out by an agency having sufficient experience in membrane water proofing and should ensure a guarantee of 10 years. Only skilled and experienced persons shall be employed for this purpose.)

Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and laying PVC membrane waterproofing system in horizontal plane including adjustment layer to take up any surface irregularities of the substrate, in order to avoid any imperfections or foreign particles damaging the waterproof layer. It shalll composed of geotextile, weight of 300 g/m2, laid in dry conditions with edge overlap of 10/15 cm. Synthetic membrane of plasticized PVC, 2mm thick of approved manufacturer shall conform to the physical and chemical properties such as: Elongation at break (300%) UNI EN ISO 527-3 or equivalent, Ultimate Tensile Strength (> 16.7 N/mm²), Puncture resistance (> 1100mm) DIN 16726-5.12 or equivalent, Hydrostatic pressure Waterproof UNI EN 1928 resistance (6 hours at 5 bar) or equivalent. Double seam welding of PVC waterproofing membrane joints shall be pressure tested to 2 bars of 10 minutes .The waterproofing project to be divided into sectors if required and it is composed of shaped joints of PVC and it is welded to the existing waterproof liner. The rate shall be inclusive of providing and laying protection layer of non-woven 300gsm geo-textile membrane over the laid PVC waterproof membrane system, followed by a cement mortar screed of 50mm thick over the top layer of geo-textile membrane to facilitate the placing and tying of reinforcement bars of raft and all pressure release mechanism etc complete as directed by the Engineer-In-Charge.(The above work shall be carriedout by an agency having sufficient experience in membrane water proofing and should ensure a guarantee of 5 years). Only skilled and experienced persons shall be employed for this purpose.

Providing and Iaying PVC membrane waterproofing system over the vertical side for vertical wall,Installing geotextile of 300gsm as correction layer, over the vertical side of the wall before installation PVC membrane 2mm thick of approved manufactor shall conform to the physical and chemical properties such as: Elongation at break (300%) UNI EN ISO 527-3 or equivalent, Ultimate Tensile Strength (> 16.7 N/mm²), Puncture resistance (> 1100mm) DIN 16726-5.12 or equivalent, Hydrostatic pressure Waterproof UNI EN 1928 resistance (6 hours at 5 bar) or equivalent on vertical side, providing and fixing suitable arrangement for fixing mechanically onto the vertical wall to hold the membrane in vertical position against sagging due to self weight of the membrane and without damaging the PVC membrane and providing and Installing 2mm thick synthetic membrane of plasticized PVC with double seam welding of PVC waterproofing membrane joints and pressure testing of the same to 2 bars up to 10 minutes and with compartmentalization by welding PVC water stop with welding fins at all construction joints and at strategic locations to make a compartment of 200 sqmtrs pre installed with required number of injection flanges in every compartment fitted with inlet / outlet pipe and surface access box. The cost shall include the cost for providing and Installing a minimum protection layer of 300gsm or 25mm thick EPS protection boards over the vertically installed PVC waterproofing membrane, on the vertical face of the retaining wall to act as a protection layer against backfill and all pressure release mechanism etc complete as directed by the Engineer In Charge. (The above work shall be carried out by an agency having sufficient experience in membrane water proofing and should ensure a guarantee of 5 years). Only skilled and experienced persons shall be employed for this purpose. Only external surface area of retaining wall will be measured.)

(SH: - 14.0 - DISMANTLING WORKS) Saw cutting Cement Concrete pavement/PQC up to 30cm using specialized machinery without damaging balance pavement at site as per specification and directions of the Engineer in charge .

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-Charge: Nominal concrete or leaner mix (i/c equivalent design mix)

Demolishing brick/block work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.

Dismantling doors, windows and clerestory windows (Aluminium,steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (Aluminium,steel or wood) shutter including chowkhats, architrave, holdfasts etc. Complete and stacking within 50 metres lead: of area beyond 3.00 sqm

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : Of sectional area 40 square centimetres and above

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: R.S. Joists as directed by Engineer in charge.

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: Channels, angles, tees and flats as directed by Engineer in charge.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, sutting rivets, welding etc. incluing dismembering and stacking within 50 metres lead.

Dismantling tile work at all levels in floors ,walls ,roofs laid in cement mortar/ adhesive including stacking material within 5km lead as per direction of Engineer-in-Charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling aluminium/Gypsum/ply/acrylic/glass /compact laminate/polycarbonate partitions, fixed glazing, cladding and false ceiling including glass wool & suspension system including dismantling of terminals like light fixtures/ sprinklers/difusers/grills etc ,conduits,wires etc at all levels and disposal of unserviceable surplus material and stacking of serviceable material with in 5km lead or CIAL store as directed by Engineer-in-Charge.

Demolishing R.C.C work, including stacking of steel bars and disposal of unserviceable material within 5KM lead as per direction of Engineer-in-Charge

Removal of external facade / Aluminium curtain wall glazing and taking out DGU /Spandrel glass unit from glass assembly and staking the same safely in approved location without damaging the existing structure including supporting members, stacking within the Airport premises including all labour charges,lead,lift,scaffoldings etc complete as directed by Engineer-in-Charge at all levels.

Providing vibrationless accurate wet cutting of RCC slabs of all thicknessfor making openings at all levels with medium to heavy-duty, high performance remote controlled diamond hydraulic cutting machines with the assitance of blades using all tools and tackles complete, without any disturbance to the adjacent structure and including lowering of cut pieces using suitable arrangement like chain pulley block for safe lowering onto ground, breaking and separating of debris from reinforcement, handling of cutpieces and cordoning and dust proof the area properly and with necessary formwork to support the existing structure including cost and conveyance of all materials, labour, lead lift , etc. complete and disposal of material within 5km lead as per direction of Engineer-in-Charge. Plan area of the slab to be measured for payment. Any damage to the adjacent structure shall be corrected without any additional cost upto the satisfaction of Engineer in charge. The above work shall be carried out by an agency having sufficient experience and only skilled and experienced persons shall be employed for this purpose.

Dismantling of flexible pavement ( bituminous courses ) by mechanical means and disposal of dismantled material up to a lead of 1 kilo metre, as per direction of Engineer-in-charge.

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in-Charge: WBM/ WMM/GSB

Cleaning and removal of slush/debris /water from existing sump depth up to 4.0m by after closing the inlet valves and plugging any holes in the steining by engaging labours, bailing out water using pumset of suitable capacity, lifting the excavated silt/mud/clay using ropes, pulleys and buckets and disposing the same to the out side of CIAL premises from thesump, including engaging coolies cluding hire and conveyance of tools and plant etc complete and as per the directions of the engineer in charge

Dismantling of existing gutter lining with required accessories etc without damaging the existing roofing sheet by making temporary working arrangement for executing the work and disposal to dumping yard within 5 km lead including all labour charges,lead,lift,scaffoldings etc complete as directed by Engineer-in-Charge at all levels.

Dismantling existing baggage conveyor system including dismembering entire system including steel work ,all related accessories including all gusset plates, bolts, nuts, sutting rivets, welding etc. incluing dismembering and stacking within the cial premises as directed by engineer in charge.

Description of Work / Item(s)

Amount

Installation, Testing and Commissioning of MSB including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of MCC-3 including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of ACSB including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of Lighting SB including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

ODP Supply of outdoor type light control panel board with canopy, made out of modular polycarbonate thermoplastic enclosures IP65, floor/ wall mounting, suitable for operation on 3 phase , 415 V, 50Hz AC system with busbars , including internal wiring with suitable size HFFR wires/cable, interconnection. The panel shall be have CPRI certification in accordance with relevant IEC codes. The gasket material shall be polyurethane and internally embedded and with following switchgears, metering instruments and accessories etc. complete as required as per drawing & specification. Incomer : 32A, FP MCB - 1 no Instruments: Surge arrestor Type 1 & 2 - 1 no, 2A Fuse - 1 set, RYB indication lamp, LED type - 1 set, Space provision for mounting digital time switch with inbuilt battery & contactor Out Going: 25A DP RCCB +MCB 100mA - 5 nos , 16A DP RCCB +MCB 100mA - 3 nos ,Digital time switch with 25A DP contactor - 5 nos , Digital time switch with 16A DP contactor - 3 nos , ON/OFF/TRIP indication lamp, LED type - 8 Nos

Installation, Testing and Commissioning of ODP including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

UPS AND ACCESSORIES Supply of 10 kVA, three phase input, Three Phase output, true on-line UPS system with 15mins back up , output isolation transformer, including all accessories, SMF batteries VRLA type with powder coated CRCA cabinet including all accessories such as output panel required for ups parellel operation, cabling etc as required complete having following specification.The UPS system consist of two numbers of UPS unit and two set of battery bank . The UPS shall be suitable for parellel operation. Fully digital controlled based on DSP, Power factor corrected from end > 0.9, Pure sine wave output, Full time output voltage & frequency regulation, Auto regulation of battery end voltage, Intelligent interface with LED/LCD display, Static bypass switch / manual by pass switch, Auto temperature compensation, Remote Management Interphase, Back up time 15 minutes at full load.

Installation, Testing and Commissioning of 10kVA UPS System including hoisting to the respective location, assembling of batterys, lining up, bolting the units, checking all the control wirings, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

CABLES AND CABLING Supply of following size 1.1 KV grade XLPE insulated, PVC sheathed, armoured FRLS Aluminium /copper conductor cable conforming to IS 7098 (Part 1) amended upto date.

3.5C 400 Sq.mm Al

3.5C 240 Sq.mm Al

3.5C 120 Sq.mm Al

4C 35 Sq.mm Al

4C 25 Sq.mm Al

4C 16 Sq.mm Al

4C 6 Sq.mm Cu

4C 4 Sq.mm Cu

4C 2.5 Sq.mm Cu

2C 6Sq.mm Cu

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3.5C 400 Sq.mm Al

3.5C 240 Sq.mm Al

3.5C 185 Sq.mm Al

3.5C 120 Sq.mm Al

4 C 35 Sq.mm Al

4C 25 Sq.mm Al

4C 16 Sq.mm Al

4C 6 Sq.mm Cu

4C 4 Sq.mm Cu

4C 2.5 Sq.mm Cu

2C 6Sq.mm Cu

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Upto 35 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required

Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required

600 MM WIDTH X 50 MM DEPTH X 2 MM THICK

300 MM WIDTH X 50 MM DEPTH X 2 MM THICK

Fabrication, supply and installation of following size of perforated Type GI cable tray including horizontal and vertical reducers,bends, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required

600 MM WIDTH X 50 MM DEPTH X 1.6 MM THICK

300 MM WIDTH X 50 MM DEPTH X 1.6 MM THICK

150 MM WIDTH X 50 MM DEPTH X 1.6 MM THICK

Supply, fabricating and installing MS items such as Tees/ angles/ channels etc. on floor/ ceiling/ wall including necessary civil work such as grouting, finishing etc. and painting with two coats of primer and two coats of synthetic enamel paint as required

Supply and fixing of chequered plate of 6 mm thick including cutting to required size using gas cutter and lay the same over the trench, fixing of nosing angle and supports for chequered plate, related civil works, finishing etc. and painting with two coats of enamel paint over one coat of Zinchromate primer as required.

Providing & fixing Fire Barrier mortar with minimum 2 hours fire rating when tested in accordance with BS 476 part 20 and UL 1479 for horizontal openings in fire rated floors or slabs and vertical openings in walls for passing service shafts. The service lines could be of various types like electrical cables trays, metal pipes, GI Ducts for AC, etc.The mortar shall have minimum hardened density of 0.8 g/cm3 and It should have a compressive strength of 2.9N/Sq mm . The product shall be Smoke & Air Seal and 30 years Age tested as per Dafstb and DIBT standards. The product shall be tested and approved by third party agencies such as UL and FM. The mortar should be tested in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The product shall bear the UL and FM approval logo on the packing where applicable.

EARTHING & SAFETY EQUIPMENTS Supply of all the materials required for maintenance free earthing system including 3 mtrs length,20mm dia 250 microns molecularly copper bonded steel rod with stainless steel connectors and fasteners for connecting earth strip, earth enhancing compound (12.5 kg mineral compound / 22.6 kg low resistivity graphite compound),FRP (UFE FRP) earth electrode inspection chamber with heavy duty cover of 300mmx 300mmx 300mm dimension havinng bearing capacity of 15KN etc as required.

Installation ,testing and comissioning of maintenance free earthing using 3 mtrs length,20mm dia 250 microns molecularly copper bonded steel rod, stainless stell connectors and fasteners for connecting earth strip.The earth electrode shall be filled with earth enhancing compound (12.5 kg mineral compound / 22.6 kg low resistivity graphite compound).FRP (UFE FRP)Earth electrode inspection chamber with heavy duty cover should be used to cover the Earth Rod. The dimension of cover shall be 300mmx 300mmx 300mm with a weight bearing capacity of 15KN.The rate shall be inclusive of installation charges,including digging bore,providing all required accessories like terminal connector,screw for fixing earth pit cover etc.

Supply of copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with heavy duty CI cover plate of 300X300mm having locking arrangement and watering pipe of 2.7 metre long etc. with 96 kg charcoal/ coke and 5 kg salt as required. (As per IS 3043 ammended uptodate)

Installation ,testing and comissioning of copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with heavy duty CI cover plate of 300X300mm having locking arrangement and watering pipe of 2.7 metre long etc. with 96 kg charcoal/ coke and 5 kg salt as required. (As per IS 3043 ammended uptodate)

Supply of 25mm X 6mm hot dip galvanized GI strip.

Laying of 25mm X 6mm GI strip on the cable tray / surface with mounting saddles for conductor earth electrode including welding etc as required.

Laying of bare earthing conductors of 25mm X 6mm GI strip laid 0.5m below ground level including excavating trench of suitable size and refilling etc. as required

Supply of 25mm X 3mm Cu copper strip.

Laying of 25mm X 3mm CU strip(tinned at the points of contacts) on the cable tray / surface with mounting saddles for conductor earth electrode including welding etc as required.

Supply of 3.15mm Cu (10 SWG)copper wire

Laying of 3.15mm Cu (10 SWG)copper wire on the cable tray / surface with mounting saddles for conductor earth electrode including welding etc as required.

Supply of of 4.00 mm hot dip galvanized GI (8 SWG) wire

Laying of 4.00 mm GI (8 SWG) wire on the cable tray / surface with mounting saddles for conductor earth electrode including welding etc as required.

Laying of bare earthing conductors of 4.00 mm GI (8 SWG) wire laid 0.5m below ground level including excavating trench of suitable size and refilling etc. as required

Supply of fire retardant/extinguishing electrical insulated synthetic mat of 2m x 1m x 2.5 mm for 11kV grade thick, +/- 10% confirming to BIS: DOC No. ET-02 (5440) meeting requirements of IS:15652:2006 (with upto date amendment), suitable for 11kV voltage and having minimum width of 1000mm +/- 20mm and including supply of required quantity of adhensive / compound .

Fixing of fire retardant/extinguishing electrical insulated synthetic mat of 2m x 1m x 2.5 mm for 11kV grade thick, +/- 10% confirming to BIS: DOC No. ET-02 (5440) meeting requirements of IS:15652:2006 (with upto date amendment), suitable for 11kV voltage and having minimum width of 1000mm +/- 20mm and including fixing of required quantity of adhensive / compound at site as per site requirement.

Supply & fixing of First aid box

Supplying of Rubber hand gloves suitable for 1.1 KV.

Supply & fixing of anodised aluminum glass framed shock treatment chart.

Supply & Fixing of single line diagram, schematic diagrams etc. of A1 size on suitable Aluminium sheet including lamination etc. as required complete on wall.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as per the I.E. specifications.

MCBs & DISTRIBUTION BOARDS Supply of 8 way (8 + 24), double door, three pole and neutral, sheet steel, powder coated, Vertical MCCB distibution board (LOAD BANK) 415 volts, complete with , tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for upto 160A, 4P, MCCB as incomer.

ITC of 8 way (8+24) double door, three pole and neutral, sheet steel, powder coated, Vertical MCCB distribution board (LOAD BANK) , 415 volts, fixing required number of TP/FP MCBs, RCCBs/MCCBS, Blanking plates, cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required, finishing ,making good the same etc complete.

Supply of 8 way (8 + 24), double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required . suitable for single phase out goings and separate cut-out for 4P RCCB and TP/ SP MCB for incoming etc. as required and as per specification (IP 42/43 type).

ITC of 8 way (8+24) double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts, fixing required number of SP/TP/FP MCBs, RCCBs, Blanking plates,cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required, finishing, making good the same etc complete.

Supply of 4 way (8 + 12), double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required . suitable for single phase out goings and separate cut-out for 4P RCCB and TP/ SP MCB for incoming etc. as required and as per specification (IP 42/43 type).

ITC of 4 way (8+12) double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts, fixing required number of SP/TP MCBs, 4PRCCBs, Blanking plates,cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required, finishing, making good the same etc complete.

Supply of 8 way (8 + 24) double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for single phase out goings and separate cut-out for 4P RCCB and 4P MCB for incoming etc. as required and as per specification (IP 42/43 type).

ITC of 8 way (8 + 24) double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, fixing required number of TP/FP MCBs, RCCBs, Blanking plates,cable entry box, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 4 way double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for single phase out goings and separate cut-out for 4P RCCB and 4P MCB for incoming etc. as required and as per specification (IP 42 type).

ITC of 4 way double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, fixing required number of TP/FP MCBs, RCCBs, Blanking plates,cable entry box, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required, finishing , making good the same etc complete.

Supply of 12 way double door, single pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 240 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for single phase out goings and separate cut-out for DP RCCB and DP MCB for incoming etc. as required and as per specification (IP 42/43 type).

ITC of 12 way double door, single pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 240 volts, fixing required number of SP MCBs, DP RCCBs, Blanking plates,cable entry box, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of cable end box for three pole and neutral, sheet steel, powder coated, Vertical MCCB distribution board, 415 volts with all necessary accessoires as required complete.

Supply of cable end box for three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts with all necessary accessoires as required complete.

Supply of cable end box for 8 way (8 + 24) double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board 415 volts with all necessary accessoires as required complete

Supply of cable end box for 12 way double door, single pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 230 volts with all necessary accessoires as required complete

Fixing of cable end boxes for DBs with all necessary accessoires as required complete.

Supply of 6 amps to 32 amps rating, 240 volts,Single pole “C” curve, miniature circuit breaker.

Supply of 6 amps to 32 amps rating, 240 volts, Double pole “C” curve, miniature circuit breaker.

Supply of 6 amps to 32 amps rating, 415 volts,Triple pole “C” curve, miniature circuit breaker.

Supply of 40 amps to 63 amps rating, 415 volts,Triple pole C” curve, miniature circuit breaker.

ITC of 6 amps to 63 amps rating, 415 volts,SP/DP/ TP/ FP miniature circuit breaker.

MCCB Supply of 125 Amp, 16kA,415 volts,TP,MCCB with adjustable thermal magnetic release with OL & SC protection.

Fixing of 125 Amp, 16kA,415 volts,TP,MCCB with adjustable thermal magnetic release with OL & SC protection.

ISOLATOR Supply of 63 A FP isolator with weather proof enclosure with all other accessories as required complete

Supply of 32 A FP isolator with weather proof enclosure with all other accessories as required complete

ITC of 63/ 32 A FP isolator with weather proof enclosure with all other accessories as required complete

Supply of 32 A DP isolator with weather proof enclosure

Fixing of 32 A DP isolator with weather proof enclosure with all other accessories as required complete

RCBO Supply of 2 pole 25 amps. (240 Volts), 30mA sensitivity. residual current breaker (RCBO) .

ITCof 2 pole 32 amps. (240 Volts), 30mA sensitivity. residual current breaker (RCBO) .

Supply of 4 pole 40amps. (415 Volts), 30mA sensitivity. residual current breaker (RCBO) .

Supply of 4 pole 40amps. (415 Volts), 100mA sensitivity. residual current breaker (RCBO) .

Supply of 4 pole 63amps. (415 Volts), 100mA sensitivity. residual current breaker (RCBO) .

ITC of 4 pole 40/ 63 amps. (415 Volts), residual current breaker (RCBO) .

Supply of DOL starter for upto 5HP,3ph motor including auxilliary contactors, with suitably rated capacitors as per standards and all necessary accessories as required complete.

ITC of DOL starter for 5HP,3ph motor including auxilliary contactors, with suitably rated capacitors as per CEIG standards and all necessary accessories as required complete.

Supply of outdoor type START/STOP (2way) push button station (IP65) including all the necessary accessories as required complete with suitable mounting arrangement.(Cat No Hensel-PBS 0201 or equivalent approved make)

Fixing of outdoor type START/STOP (2way) push button station (IP65) including all the necessary accessories as required complete with suitable mounting arrangement.(Cat No Hensel-PBS 0201 or equivalent approved make)

WIRING AND ACCESSORIES Supply of 20mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes ,couplers ,saddles etc as detailed in technical specification.

Laying of 20mm dia PVC conduit along with accessories like PVC bends,couplers,junction box,fastners, iron staples/saddles/screws,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification.

Supply of 25mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes ,couplers ,saddles etc as detailed in technical specification .

Laying of 25mm dia PVC conduit along with accessories like PVC bends,couplers,junction boxes,fastners, iron staples/saddles/screws,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification.

Supply of 32mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes ,couplers ,saddles etc as detailed in technical specification

Laying of 32mm dia PVC conduit along with accessories like PVC bends,couplers,junction boxes,fastners, iron staples/saddles/screws,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification.

Supply of 20mm dia corrugated good quality flexible PVC conduit along with adaptors and all other accessories as required complete.

Laying of 20mm dia corrugated good quality flexible PVC conduit along with adaptors and all other accessories as required complete.

Supply of thermoplastic shock / rust /dust /water proof, IP 65 139x119x70mm enclosure having internally embedded gasket and suitable dust caps to seal the mounting slots and provision for cable entry on all sides

Layingof thermoplastic shock / rust /dust /water proof, IP 65 139x119x70mm enclosure having internally embedded gasket and suitable dust caps to seal the mounting slots and provision for cable entry on all sides

Supply of thermoplastic polystyrene IP 68 139x119x70mm enclosure with suitable connectors/ terminals and complete with all other accessories as required complete

Fixing of thermoplastic polystyrene IP 68 139x119x70mm enclosure with IP65 glands, suitable connectors/ terminals and complete with all other accessories as required complete

Supply of 1.5sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Drawing of 1.5sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Supply of 2.5sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Drawing of 2.5sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Supply of 4sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Drawing of 4sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Supply of 6sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Drawing of 6sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Supply of 3C1.5 sq. mm. FRLSH PVC insulated copper conductor stranded cable

Drawing of 3C1.5 sq. mm. FRLSH PVC insulated copper conductor stranded cable in existing conduit.

Supply of 6A modular type, one way medium switch with suitable front plate, metal box and all other accessories as required complete

Supply of 6A modular type one way premium switch with suitable front plate , metal box and all other accessories as required complete

Supply of 6A modular type two way medium switch with suitable front plate, metal box and all other accessories as required complete.

Fixing 6A modular type one/ two way medium/ premium switch with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply of 6A modular type ,5pin plug medium socket with suitable front plate, metal box and all other accessories as required complete.

Supply of 6A modular type ,5pin plug premium socket with suitable front plate, metal box and all other accessories as required complete.

Fixing of 6A modular type ,5pin plug socket (medium/ premium) with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required , making good the surface etc. as required complete.

Supply of 6A modular type switch and socket socket medium with suitable front plate, metal box and all other accessories as required complete.

Supply of 6A modular type switch and socket socket premium with suitable front plate, metal box and all other accessories as required complete.

Fixing of 6A modular type switch and socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required , making good the surface etc. as required complete.

Supply of 16A modular type one way medium switch with suitable front plate, metal box and all other accessories as required complete.

Supply of 16A modular type one way premium switch with suitable front plate, metal box and all other accessories as required complete.

Fixing of 16A modular type one way medium/ premium switch with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required , making good the surface etc. as required complete.

Supply of 16A modular type ,5pin medium plug socket with suitable front plate, metal box and all other accessories as required complete.

Supply of 16A modular type ,5pin premium plug socket with suitable front plate, metal box and all other accessories as required complete.

Fixing of 16A modular type ,5pin medium/ premium socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply of 16A modular type switch and socket medium with suitable front plate, metal box and all other accessories as required complete.

Supply of 16A modular type switch and socket socket premium with suitable front plate, metal box and all other accessories as required complete.

Fixing of 16A modular type switch and socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete

Supply of 25A modular type one way premium switch with suitable front plate, metal box and all other accessories as required complete.

Fixing of 25A modular type one way premium switch with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply of premium 10A international socket with suitable front plate front plate, metal box and all other accessories as required complete.

Fixing of PREMIUM international socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required , making good the surface etc. as required complete.

Supply of 230V , one module buzzer along with back box, front cover and all other accessories as required complete.

Fixing of 230V, one module buzzer alongwith backbox, front cover on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply of Screed Floor Box of 325mmX325mm ,3 compartment, including lid & trim, cover with flexible cable exit , 2 Nos 8 module flat support plate for electrical sockets ,4 module waved support plates for data sockets and including all other accessories required completely.(Make: Legrand 689634, 689631, 689617, 689678 or equivalent approved make)

Fixingof Screed Floor Box with all the necessary accessories as required complete.

Supply of 2x4 module metalic floor pop up outlet with stainless steel finish,soft opening,push and slide locking system , suitable for using in concrete floors or raised access floors including floor box as required . (Make: Legrand 054023, 054003 or equivalent approved make)

Fixing of 2x4 module metalic floor pop up outlet with all accessories like floor box etc required for the complete installation including cutting the floor if required and making good the same .

Supply of 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps “C” curve, SP, MCB, in sheet steel enclosure with chained metal cover for the socket out let .

ITC of 20 amps, 240 volts, SPN industrial type, socket outlet, alongwith 20 amps “C” curve, SP, MCB, on surface or in recess, inter connections, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 32 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 32 amps “C” curve, TPN, MCB, in sheet steel enclosure with chained metal cover for the socket out let and complete .

ITC of 32 amps, 415 volts, TPN industrial type, socket outlet, alongwith 32 amps “C” curve, TP, MCB, on surface or in recess, inter connections, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of blanking plate with suitable front plate, metal box and all other accessories as required complete.

Fixing of blanking plate in existing switch box as required complete.

ITC OF LIGHT FIXTURES Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLSH PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation Testing and commissioning of LED striplight with all mounting accessories as required complete including interconnections using 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation Testing and commissioning of driver of LED striplight with all mounting accessories as required complete

Installation Testing and commissioning of LED down lighter fittings on false ceiling with all mounting accessories, drivers as required complete including interconnections using 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation testing and commissioning of prewired LED linear fittings of all types including complete with all accessories, lamps, drivers, suspension kits, as required etc. on false ceiling including fixing of GI chain and hook arrangement and wiring 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation testing and commissioning of prewired LED linear fittings of all types including complete with all accessories, lamps, drivers etc. on false ceiling including fixing of GI chain and hook arrangement and wiring 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation testing and commissioning of prewired LED panel light fittings of all types including complete with all accessories, lamps, drivers etc. on false ceiling including fixing of GI chain and hook arrangement and wiring 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation, testing and commissioning of chandelier , including fixing and wiring the down rods as required , lamps, drivers, with 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation, testing and commissioning of pendant lights/ mini chandeliers , including fixing and wiring the down rods as required, lamps, drivers with 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation, testing and commissioning of wall light fitting , complete with all accessories,lamps, drivers etc. directly on wall, including connection with 1.5 sq. mm FRLSH PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of pedestal lamps , including fixing and wiring with 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, lamps, drivers, cable and earthing etc. as required.

Installation, testing and commissioning of decorative lights at Jali , including fixing and wiring with 3C1.5 sq. mm FRLSH PVC insulated, lamps, drivers, copper conductor, cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including fixing and wiring the down rods with 3C1.5 sq. mm FRLSH PVC insulated, copper conductor, cable and earthing etc. as required.

Installation, testing and commissioning of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of the fan, making good the damage, connections, testing & commissioning etc as required.

Numbering of ceiling fan / exhaust fan/ fluorescent fitting as required.

ITC of post top lantern, built- in control box prewired, with pole suitable for mounting LED luminairie with lamp , concealed wiring with 3Cx 2.5 sq.mm copper wire from the control box to light fixture, provision for mounting RCBO/MCB in the control box as required and all other accessories complete including all necessary accessories as required complete. Note:Incoming and outgoing cable at termination box shall be terminated with glands properly

ITC of Bollard suitable for operation on 240V, 50Hz single phase ac supply along with driver and surge protection,and including all necessary accessories as required complete.

ITC of tree focus / inground luminaires suitable for operation on 240V, 50Hz single phase ac supply along with driver and surge protection, junction boxes and including all necessary accessories as required complete.

ITC of up/ down/ updown/ wall washer luminaires at elevation facia on wall/Column/truss suitable for operation on 240V, 50Hz single phase ac supply along with driver and surge protection, junction boxes and including connections with 3C 1.5 Sq.mm PVC insulated flexible copper conductor cable as required.

ITC of High bay/LED/ FLOOD type fittings on wall/Column/truss/false ceiling using suitable MS clamps, nuts, bolts/ 20mm heavy duty GI chain/ pipe (upto 50cm)etc uitable for operation on 240V, 50Hz single phase ac supply along with driver and surge protection, junction boxes and including connections with 3C 1.5 Sq.mm PVC insulated flexible copper conductor cable as required.

REMOTE SENSING DOOR Supply of Remote sensing door without breakout panels and with side screens; framed construction with pivot fittings firmly secured to the header construction, profile shall conform to ST flex leak/SL BO profille. The finish shall be anodized and colour as approved by Engineer in Charge, and the door shall open on power failure (with back-up battery pack), with automatic control of the door panel movements. Manufactured in accordance with German code of practice ZH 1/494 governing power-operated windows, doors and gates, German UVV (accident prevention) regulations, and VDE (Association of German Engineers) regulations (latest edition in each case), Complaint with DIN 18650 Safety Standards for Pedestrian Doors and TUV Design Tested for Durability of 1 Million Cycles, sliding door operator, with maximum Operator Dimensions 100X180mm (height X Depth), With Internal Cover and with mounting back plate for easy installation and a flexible track profile for improved noise & vibration dampening and easy maintenance. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Automatic control shall be done by two RADAR detectors with a range of operating, control options and safety devices, Class of protection for RADAR shall be IP 20. Actuators- approved 6 Safe Combination Sensor System (02 Nos),magnetic contact switch for air curtain, Light barriers comprising receiver and transmitter ( 02 set )for through-passage monitoring with Electro-mechanical locking, Bistable, Program Switch, baggage trolley sensor and manual bypass switch . Operators minimum weight carrying capacity shall be100 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC and shall be provided with bypass switch. All glass shall be 12 mm thick toughened heat soaked.Door shall be provided with with UPS of minimum 600VA for minimum operation of 30 cycles/30 minutes. The tile cutting for U channel of 25x40mm channel fixing, making good the floor shall be done as directed by the Engineer in Charge The system shall be complete as per design and instructions of Engineer-in-Charge. RSD 2 m x2.4 m (Clear opening size is 4.15m x 2.55m ). Rate shall include the cost of fixed glass panels and openable panels of overall dimension 4.15mx 2.55m

ITC of Remote sensing door without breakout panels and with side screens; framed construction with pivot fittings firmly secured to the header construction, profile shall conform to ST flex leak/SL BO profille. The finish shall be anodized and colour as approved by Engineer in Charge, and the door shall open on power failure (with back-up battery pack), with automatic control of the door panel movements. Manufactured in accordance with German code of practice ZH 1/494 governing power-operated windows, doors and gates, German UVV (accident prevention) regulations, and VDE (Association of German Engineers) regulations (latest edition in each case), Complaint with DIN 18650 Safety Standards for Pedestrian Doors and TUV Design Tested for Durability of 1 Million Cycles, sliding door operator, with maximum Operator Dimensions 100X180mm (height X Depth), With Internal Cover and with mounting back plate for easy installation and a flexible track profile for improved noise & vibration dampening and easy maintenance. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Automatic control shall be done by two RADAR detectors with a range of operating, control options and safety devices, Class of protection for RADAR shall be IP 20. Actuators- approved 6 Safe Combination Sensor System (02 Nos),magnetic contact switch for air curtain, Light barriers comprising receiver and transmitter ( 02 set )for through-passage monitoring with Electro-mechanical locking, Bistable, Program Switch, baggage trolley sensor and manual bypass switch . Operators minimum weight carrying capacity shall be100 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC and shall be provided with bypass switch. All glass shall be 12 mm thick toughened heat soaked.Door shall be provided with with UPS of minimum 600VA for minimum operation of 30 cycles/30 minutes. The tile cutting for U channel of 25x40mm channel fixing, making good the floor shall be done as directed by the Engineer in Charge The system shall be complete as per design and instructions of Engineer-in-Charge RSD 2 m x2.4 m (Clear opening size is 4.15m x 2.55m )

Supply of Remote sensing door with breakout panels and side screens; framed construction with pivot fittings firmly secured to the header construction, profile shall conform to ST flex leak/SL BO profille. The finish shall be anodized and colour as approved by Engineer in Charge, and the door shall open on power failure (with back-up battery pack), with automatic control of the door panel movements. Manufactured in accordance with German code of practice ZH 1/494 governing power-operated windows, doors and gates, German UVV (accident prevention) regulations, and VDE (Association of German Engineers) regulations (latest edition in each case), Complaint with DIN 18650 Safety Standards for Pedestrian Doors and TUV Design Tested for Durability of 1 Million Cycles, sliding door operator, with maximum Operator Dimensions 100X180mm (height X Depth), With Internal Cover and with mounting back plate for easy installation and a flexible track profile for improved noise & vibration dampening and easy maintenance. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Automatic control shall be done by two RADAR detectors with a range of operating, control options and safety devices, Class of protection for RADAR shall be IP 20. Actuators- approved 6 Safe Combination Sensor System (02 Nos),magnetic contact switch for air curtain, Light barriers comprising receiver and transmitter ( 02 set )for through-passage monitoring with Electro-mechanical locking, Bistable, Program Switch, baggage trolley sensor and manual bypass switch . Operators minimum weight carrying capacity shall be100 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC and shall be provided with bypass switch. All glass shall be 12 mm thick toughened heat soaked.Door shall be provided with with UPS of minimum 600VA for minimum operation of 30 cycles/30 minutes. The tile cutting for U channel of 25x40mm channel fixing, making good the floor shall be done as directed by the Engineer in Charge The system shall be complete as per design and instructions of Engineer-in-Charge RSD 2 m x2.4 m (Clear opening size is 4.15m x 2.55m ).The rate shall include the cost of breakout glass panels for over dimension of 4.15m x 2.55m.

Installation, Testing and Commissioning of Remote sensing door with breakout panels and with side screens; framed construction with pivot fittings firmly secured to the header construction, profile shall conform to ST flex leak / SL BO profile. The finish shall be anodized and colour as approved by Engineer in Charge, and the door shall open on power failure (with back-up battery pack), with automatic control of the door panel movements. Manufactured in accordance with German code of practice ZH 1/494 governing power-operated windows, doors and gates, German UVV (accident prevention) regulations, and VDE (Association of German Engineers) regulations (latest edition in each case), Complaint with DIN 18650 Safety Standards for Pedestrian Doors and TUV Design Tested for Durability of 1 Million Cycles, sliding door operator, with maximum Operator Dimensions 100X180mm (height X Depth), With Internal Cover and with mounting back plate for easy installation and a flexible track profile for improved noise & vibration dampening and easy maintenance. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Automatic control shall be done by two RADAR detectors with a range of operating, control options and safety devices, Class of protection for RADAR shall be IP 20. Actuators- approved 6 Safe Combination Sensor System (02 Nos),magnetic contact switch for air curtain, Light barriers comprising receiver and transmitter(02 Set) for through-passage monitoring with Electro-mechanical locking, Bistable, Program Switch, baggage trolley sensor and manual bypass switch . Operator’s minimum weight carrying capacity shall be100 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC and shall be provided with bypass switch. All glass 12mm thick toughened heat soaked.Door shall be provided with with UPS of minimum 600VA for minimum operation of 30 cycles/30 minutesThe tile cutting for U channel of 25x40mm channel fixing, making good the floor shall be done as directed by the Engineer in Charge The system shall be complete as per design and instructions of Engineer-in-Charge RSD 2 m x2.4 m (Clear opening size is 4.15m x 2.55m )

SEWAGE PUMPS Supplying of non clog centrifugal sewage pump with CI construction,SS impeller complete with motor ,base plate, foundation bolts, nuts, pressure guage and all necessary accessories and working with 415V, 3ph and 50 Hz frequency,Capacity:15m3/hr,Head :10metres

Installation, testing and commissioning of non clog centrifugal sewage pump with CI construction,SS impeller complete with motor ,base plate, foundation bolts, nuts, pressure guage and all necessary accessories and working with 415V, 3ph and 50 Hz frequency,Capacity:15m3/hr,Head :10metres

DISMANTLING ITEMS Dismantling and relocation of the existing LT panel boards from the electrical room to the respective floors/locations including loading, unloading and transportation from the existing location and installation, testing and commissioning of the same at the new location.

Dismantling of Electrical cables, allied terminations & earthing strips & wires of all sizes from under/above ground position with all leads , lifts and stacking the same at the space provided by the purchaser/ client within the premise of client.

Dismantling of MCB distribution Boards with all accessories including MCB, ELCB, etc with all leads, lifts and stacking the same at the space provided by the purchaser/ client within the premise of client.

Dismantling of wires & conduits with all accessories with all leads, lifts and stacking the same at the space provided by the purchaser/ client within the premise of client. Note: Damaged/old light fittings not included in this BOQ Iitem,which are not in the scope of civil contractor , has to be dismnatled by electrical contractor. These light fittings will be the property of the electrical contractor and no dismatling rate will be paid for these items.

HVAC WORKS Design, manufacturing, supply, of Screw Type Water Cooled Chilling Machine of minimum 350 TR capacity and a COP greater than as mentioned in Table 9.4 of ECBC -latest edition, comprising hermetic/semi hermetic screw type compressor with motor suitable for operation on 415 +/- 10% Volts 3 Ph, 50 cycles power supply with suitable starter including shell and tube type chiller, shell and tube type water cooled condenser, refrigerant piping, system control wiring, water flow switches complete with accessories and safety controls along with microprocessor control panel compatible with MODBUS/BACNET complete as per specifications. The chiller package shall be assembled on a common fabricated steel frame to form a compact unit and shall be first charged with R134a refrigerant gas and oil etc. MCCB's should be as part of the chiller and the starter panel shall be in the chiller supplier's scope. Purchaser will provide suitable rated power as a single feeder and earth. Motor shall be suitable for 415V±10%V, 3ph/50Hz AC power supply. Chiller shall be complete in all respects as per the technical specifications. Chilled water Leaving Temp. : 45 °F Chiller water Entering Temp. : 55 °F Chilled Water Flow rate : 840 US gpm Condenser water Entering Temp. : 90 °F Condenser Water Flow rate : 1050 US gpm Chiller Fouling Factor : 0.0005sqft Deg Fhr/Btu Condenser Fouling Factor : 0.001sqft Deg Fhr/Btu Minimum energy efficiency requirements shall be COP -5.8 IPLV-6.8

Installation, testing and commissioning of Screw Type Water Cooled Chilling Machine of minimum 350 TR capacity and a COP greater than as mentioned in Table 9.4 ECBC-latest edition, comprising hermetic/semi hermetic screw type compressor with motor suitable for operation on 415 +/- 10% Volts 3 Ph, 50 cycles power supply with suitable starter including shell and tube type chiller, shell and tube type water cooled condenser, refrigerant piping, system control wiring, water flow switches complete with accessories and safety controls along with microprocessor control panel compatible with MODBUS/BACNET, Transportation and leading to this location shall be in coordination with the Engineer in charge. Chiller shall be complete in all respects as per the technical specifications

Design ,Supply of End suction top discharge centrifugal pump-set for rated continuous duty and efficiency, with necessary power & control cabling from starter panel to equipment along with ON/OFF push button for local isolation as per KSEI regulation, suitable adapter box if required and earthing, bronze Impeller, common base frame & necessary ,motor, coupling , Inertial bases and vibration isolators ,mechanical seal for recirculation of chilled water . The pump motor shall be energy efficient to IE 3, be suitable for 415 + 10% volts, 50 cycles, 3 phase, TEFC & Class F insulation. Pump set shall be complete in all respects as required by the standard specification and shall suit following minimum capacities - Primary water pump set of capacity 840 GPM at 15m of WG head.

Installing, testing and commissioning of End suction top discharge centrifugal pump-set for rated continuous duty and efficiency, with necessary Power & control cabling from starter panel to equipment along with ON/OFF push button for local isolation as per KSEI regulation, suitable adapter box if required and earthing, bronze Impeller, common base frame & necessary ,motor, coupling , Inertial bases and vibration isolators ,mechanical seal for recirculation of chilled water . The pump motor shall be energy efficient to IE 3, be suitable for 415 + 10% volts, 50 cycles, 3 phase, TEFC & Class F insulation. Pump set shall be complete in all respects as required by the standard specification and shall suit following minimum capacities - Primary water pump set of capacity 840GPM at 15m of WG head

Design ,Supply of End suction top discharge centrifugal pump-set for rated continuous duty and efficiency, complete with VFD ,suitably rated cabling from MCC to starter panel & pumps along with ON/OFF push button for local isolation as per KSEI regulation earthing ,multiple differential pressure sensor / transmitters(Differential pressure sensor/ transmitters -minimum 3 No's, along with required control cabling & shall be completely self contained units capable of relaying tranduced process variable accurately upto 2500ft away without need for any additional power source. ), motor, bronze Impeller, common base frame, coupling , Inertial bases and vibration isolators and mechanical seal for recirculation of chilled water. The pump motor shall be energy efficient to IE 3, be suitable for 415 + 10% volts, 50 cycles, 3 phase, TEFC & Class F insulation. Motor speed not to exceed 1450 rpm/2900rpm. Pump set shall be complete in all respects as per the technical specifications and shall suit following capacities- Secondary water pump set of capacity 840 GPM at 40 m of WG head.

Installing, testing and commissioning of End suction top discharge centrifugal pump-set for rated continuous duty and efficiency, complete with VFD ,suitably rated cabling from MCC to starter panel & pumps along with ON/OFF push button for local isolation as per KSEI regulation earthing ,multiple differential pressure sensor / transmitters(Differential pressure sensor/ transmitters -minimum 3 No's, along with required control cabling & shall be completely self contained units capable of relaying tranduced process variable accurately upto 2500ft away without need for any additional power source. ), motor, bronze Impeller, common base frame, coupling , Inertial bases and vibration isolators and mechanical seal for recirculation of chilled water. The pump motor shall be energy efficient to IE 3, be suitable for 415 + 10% volts, 50 cycles, 3 phase, TEFC & Class F insulation. Motor speed not to exceed 1450 rpm/2900rpm. Pump set shall be complete in all respects as per the technical specifications and shall suit following capacities- Secondary water pump set of capacity 840 GPM at 40 m of WG head

Design ,Supply of End suction top discharge centrifugal pump-set for rated continuous duty and efficiency, with necessary Power & control cabling from starter panel to equipment along with ON/OFF push button for local isolation as per KSEI regulation, suitable adapter box if required and earthing, bronze Impeller, common base frame & necessary ,motor, coupling , Inertial bases and vibration isolators ,mechanical seal for recirculation of chilled water . The pump motor shall be energy efficient to IE 3, be suitable for 415 + 10% volts, 50 cycles, 3 phase, TEFC & Class F insulation. Pump set shall be complete in all respects as per the technical specifications and shall suit following capacities- Condenser water pump set of capacity 1050 GPM at 30 m of WG head

Installing, testing and commissioning of End suction top discharge centrifugal pump-set for rated continuous duty and efficiency, with necessary Power & control cabling from starter panel to equipment along with ON/OFF push button for local isolation as per KSEI regulation, suitable adapter box if required and earthing, bronze Impeller, common base frame & necessary ,motor, coupling , Inertial bases and vibration isolators ,mechanical seal for recirculation of chilled water . The pump motor shall be energy efficient to IE 3, be suitable for 415 + 10% volts, 50 cycles, 3 phase, TEFC & Class F insulation. Pump set shall be complete in all respects as per the technical specifications and shall suit following capacities- Condenser water pump set of capacity 1050GPM at 30 m of WG head

Manufacturing, Supply of FRP Vertical induced draft counter / cross flow type Single cell Cooling Towers(CTI Certified) complete with FRP basin, FRP body, VFD Motor driven Fan, belt driven assembly, fill media, distribution basin pipe connections, Ladder, suitably rated cabling from starter panel to cooling tower along with ON/OFF push button for local isolation as per KSEI regulation, earthing ,PCC / RCC foundation as required etc. and the equipment shall be compatible with BACNET/ IP complete in all respects as per the technical specifications Condenser water leaving temperature- 90 Deg F Condenser water entering temperature-100 Deg F Wet bulb temperature- 82 deg F Water Flow rate-1050 USGPM

Installation, Testing, Commissioning of FRP Vertical induced draft counter / cross flow type Single cell Cooling Towers(CTI Certified) complete with FRP basin, FRP body, VFD Motor driven Fan, belt driven assembly, fill media, distribution basin pipe connections, Ladder, suitably rated cabling from starter panel to cooling tower along with ON/OFF push button for local isolation as per KSEI regulation, earthing ,PCC / RCC foundation as required etc. and the equipment shall be compatible with BACNET/ IP complete in all respects as per the technical specifications Condenser water leaving temperature- 90 Deg F Condenser water entering temperature-100 Deg F Wet bulb temperature- 82 deg F Water Flow rate-1050 USGPM

AIR HANDLING UNITS: Supply of 2000 cfm (5 TR) minimum capacity factory built Ceiling suspended double skin type unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13). Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including structural supports with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications

Installation ,testing and commissioning of 2000 cfm (5 TR) minimum capacity factory built Ceiling suspended double skin type unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13). Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including structural supports with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications

Supply of 6800 cfm (17 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications

Installation, Testing and Commissioning of 6800 cfm (17 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications

Supply of 8000 cfm (20 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Installation, Testing and Commissioning of 8000 cfm (20 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Supply of 12000 cfm (30 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Installation, Testing and Commissioning of 12000 cfm (30 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Supply of 14000 cfm (35 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Installation, Testing and Commissioning of 14000 cfm (35 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Supply of 16000 cfm (40 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Installation, Testing and Commissioning of 16000 cfm (40 TR) minimum capacity factory built floor mounted double skin type Air Handling Unit having EC PLUG Fans complete with external rotor BLDC motor & integrated electronic controller, potentiometer for speed control. The fan shall be suitable for BMS connectivity. Single or multiple fans shall be considered depending upon capacity of AHUs (as mentioned). The equipment shall be complete with outlet volume control dampers, canvas connections, UV Emitters with reflectors to be fixed on the coil surface with removable extruded aluminium frames. UV emitters shall be minimum 12 watt / sq.ft. of coil surface area for equal distribution. Filters Section should be with 50 mm thick washable panel type ,The efficiency of the filters shall be 90% down to particle size of 10 microns (MERV-8) and 90% down to 3.0micron (MERV13), Required starter panel ,electrical power wiring from starter panel to motor, control wiring & local isolation as per KSEI Guidelines shall be considered along with the equipment, including vibration isolators ,R.C.C foundation along with PCC/RCC subbase with bolts and nuts and finishing the slabs or any opening etc. good as same. Necessary auxiliary relay modules in the starter/ control panel to hook up with the BMS .The equipment shall be complete in all respects as per technical specifications.

Pre Insulated Chilled Water Piping: Supplying of pre insulated chilled water piping of 150 mm dia pipes (with 50 mm thick insulation ) with injected rigid polyurethane foam(CFC free) between the carrier pipe and outer protective HDPE jacket MS "C" class Heavy duty pipes complete with all grooved fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts, clamps, supports (with necessary vibration isolators ) etc. as per technical specifications and as required. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. The HDPE pipe will be as per IS 4984 with PN 2.5 rating of PE 80 material. The insulation is with 36 kg per cum PUF. The Item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of pre insulated chilled water piping of150 mm dia pipes (with 50 mm thick insulation ) with injected rigid polyurethane foam(CFC free) between the carrier pipe and outer protective HDPE jacket , MS "C" class Heavy duty pipes complete with all grooved fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts, clamps, supports (with necessary vibration isolators ) etc. as per technical specifications and as required. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. The HDPE pipe will be as per IS 4984 with PN 2.5 rating of PE 80 material. The insulation is with 36 kg per cum PUF. The item shall be complete in all respects as per technical specifications.

Supplying of pre insulated chilled water piping of 100 mm dia pipes (with 50 mm thick insulation ) with injected rigid polyurethane foam(CFC free) between the carrier pipe and outer protective HDPE jacket inside the trenches MS "C" class Heavy duty pipes complete with all grooved fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts, clamps, supports (with necessary vibration isolators ) etc. as per technical specifications and as required. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. The HDPE pipe will be as per IS 4984 with PN 2.5 rating of PE 80 material. The insulation is with 36 kg per cum PUF. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of pre insulated chilled water piping of 100 mm dia pipes (with 50 mm thick insulation ) with injected rigid polyurethane foam(CFC free) between the carrier pipe and outer protective HDPE jacket inside the trenches MS "C" class Heavy duty pipes complete with all grooved fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts, clamps, supports (with necessary vibration isolators ) etc. as per technical specifications and as required. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. The HDPE pipe will be as per IS 4984 with PN 2.5 rating of PE 80 material. The insulation is with 36 kg per cum PUF. The Item shall be complete in all respects as per technical specifications.

Supplying of pre insulated chilled water piping of 32mm dia pipes (with 50 mm thick insulation ) with injected rigid polyurethane foam(CFC free) between the carrier pipe and outer protective HDPE jacket , MS "C" class Heavy duty pipes complete with all grooved fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts, clamps, supports (with necessary vibration isolators ) etc. as per technical specifications and as required. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. The HDPE pipe will be as per IS 4984 with PN 2.5 rating of PE 80 material. The insulation is with 36 kg per cum PUF. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of pre insulated chilled water piping of 32 mm dia pipes (with 50 mm thick insulation ) with injected rigid polyurethane foam(CFC free) between the carrier pipe and outer protective HDPE jacket , MS "C" class Heavy duty pipes complete with all grooved fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts, clamps, supports (with necessary vibration isolators ) etc. as per technical specifications and as required. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. The HDPE pipe will be as per IS 4984 with PN 2.5 rating of PE 80 material. The insulation is with 36 kg per cum PUF. The item shall be complete in all respects as per technical specifications.

MS Chilled water Pipes Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.

Supply of 200mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of 200 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Supply of 100mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of 100 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Supply of 80mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of 80 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Supply of 65 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of 65 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Supply of 50 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of 50 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Supply of 32mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Laying/ fixing, testing and commissioning of 32 mm dia pipes (with 50 mm thick insulation ) of MS "C" class Heavy duty pipes complete with all fittings and accessories like Bends, Tees, reducers, expansion joints, rubber support inserts , clamps, insulated with 50 mm thick PUF insulation of 32 Kg/cm3 density confirming to standard specification and repairing of damage to building etc. The item shall be complete in all respects as per technical specifications.

Condenser Water Piping

Supply of Condenser water piping of 200 mm dia pipes of minimum 1.2mm thickness FRP coated MS "C" class Heavy duty pipes laid between cooling tower pumps ,condenser shells and cooling tower complete with all fittings and accessories like Bends, Tees, reducers, supports, clamps, etc, pipes shall be applied with bituminous primer and painted to colour codes. The item shall be complete in all respects as per technical specifications. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.

Laying/ fixing, testing and commissioning of Condenser water piping of 200mm dia pipes of minimum 1.2mm thickness FRP coated MS "C" class Heavy duty pipes laid between cooling tower pumps ,condenser shells and cooling tower complete with all fittings and accessories like Bends, Tees, reducers, supports, clamps, etc, pipes shall be applied with bituminous primer and painted to colour codes. The item shall be complete in all respects as per technical specifications provided. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.

Isolation Valves

Supply of 250 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Installation, Testing and Commissioning of 250 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Supply of 200 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as piping Complete in all respects as per technical specifications

Installation, Testing and Commissioning of 200 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Supply of 150 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Installation, Testing and Commissioning of 150 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Supply of 80 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as Chilled water piping complete in all respects as per technical specifications

Installation, Testing and Commissioning of 80 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Supply of 65 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Installation, Testing and Commissioning of 65 MM dia CI Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Supply of 50 MM dia Gunmetal Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Installation, Testing and Commissioning of 50 MM dia Gunmetal Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Supply of 32 MM dia Gunmetal Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

Installation, Testing and Commissioning of 32 MM dia Gunmetal Butterfly Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications

FLEXILE COUPLING

Supply of 200 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Installation, Testing and Commissioning of 200 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Supply of 80 MMEPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Installation, Testing and Commissioning of 80 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Supply of 65 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Installation, Testing and Commissioning of 65 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Supply of 50 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Installation, Testing and Commissioning of 50 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Supply of 32 MM EPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Installation, Testing and Commissioning of 32 MMEPDM Rubber Flexible connectors (Expansion Bellows) in chilled water lines complete in all respects as per technical specifications

Y STRAINER

Supply of 200 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Installation, Testing and Commissioning of 200 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Supply of 80 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Installation, Testing and Commissioning of 80 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Supply of 65 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Installation, Testing and Commissioning of 65 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Supply of 50 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Installation, Testing and Commissioning of 50 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Supply of 32 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

Installation, Testing and Commissioning of 32 MM dia Y-strainer in chilled water lines duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications .

2 way Pressure Independent Balancing Cum Modulating Flow Control Valves with temperature sensor

Supply of 80 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications.

Installation, testing and commissioning of 80 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications.

Supply of 65 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications.

Installation, testing and commissioning of 65 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications.

Supply of 50 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications.

Installation, testing and commissioning of 50 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications.

Supply of 32 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications.

Installation, testing and commissioning of 32 MM dia insulated electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body with digital thermostat. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. The suitable mechanism required to accept electrical power supply including step down transformer ,auxiliary relay shall be considered by the contractor. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. The valves & actuators for AHU’s units shall be compatible of linking with Building Automation System. The item shall be complete in all respects as per technical specifications

Double Regulating Valves(with 2 Test Points)

Supply of 200 MM dia Balancing Valves in chilled water lines compatible with BACNET/ IP duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications.

Installation, Testing and Commissioning of 200 MM dia Balancing Valves in chilled water lines compatible with BACNET/ IP duly insulated in the same manner and same thickness as chilled water piping complete in all respects as per technical specifications.

Non-Return Valves

Supply of 200 MM dia CI Non Return Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping etc. complete in all respects as per technical specifications.

Installation, testing and commissioning of 200 MM dia CI Non Return Valves in chilled water lines duly insulated in the same manner and same thickness as chilled water piping etc. complete in all respects as per technical specifications.

Automatic Air vents

Supply of 15 mm Automatic Air vents in chilled water lines etc. complete in all respects as per technical specifications.

Installation, testing and commissioning of 15 MM Automatic Air vents in chilled water lines etc. complete in all respects as per technical specifications.

Pressure gauge

Supply of Pressure gauge 150mm dial in chilled water lines etc. complete in all respects as per technical specifications.

Installation, testing and commissioning of Pressure gauge 150mm dial in chilled water lines etc. complete in all respects as per technical specifications.

Thermometers

Supply of 150mm stem type thermometers(0Deg C to 60Deg C) calibrated with SS thermowell in chilled water lines etc. complete in all respects as per technical specifications.

Installation, testing and commissioning of 150mm stem type thermometers(0Deg C to 60Deg C) calibrated with SS thermowell in chilled water lines etc. complete in all respects as per technical specifications.

Drain Cock

Supply of drain cocks in chilled water lines etc. complete in all respects as per technical specifications

Installation, testing and commissioning of drain cocks in chilled water lines etc. complete in all respects as per technical specifications

Self sealing test point

Supply of DZR self sealing test points in chilled water lines etc. complete in all respects as per technical specifications

Installation, testing and commissioning of DZR self sealing test points in chilled water lines etc. complete in all respects as per technical specifications

SH:2 AIR DISTRIBUTION DUCTING

Supply of 0.63 MM (24 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications (as per SMACNA Standards)

Installation, testing and commissioning of 0.63 MM (24 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications .(as per SMACNA Standards)

Supply of 0.80 MM (22 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications (as per SMACNA Standards)

Installation, testing and commissioning of 0.80 MM (22 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications (as per SMACNA Standards)

SITC of 1.00 MM (20 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications .(as per SMACNA Standards)

Installation, testing and commissioning of 1.00 MM (20 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications (as per SMACNA Standards)

Supply of 1.25 MM (18 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications .(as per SMACNA Standards)

Installation, testing and commissioning of 1.25 MM (18 Gauge) factory fabricated machine made G.I. ducting along with transverse duct flanges, supports, splitter dampers, vanes neoprene gaskets etc. Complete in all respects as per technical specifications .(as per SMACNA Standards)

Supply of Dia 200 mm Flexible insulated duct with 25 mm thick insulation duly supported at regular interval as per site requirement etc. Complete in all respects as per technical specifications

Installation, testing & commissioning of Dia 200 mm Flexible insulated duct with 25 mm thick insulation duly supported at regular interval as per site requirement etc. Complete in all respects as per technical specifications

THERMAL INSULATION

Supplying of 19 mm thick 55kg/m3 density, regular closed cell class 0 nitrile rubber insulation finished with 7 mils factory laminated glass cloth ,anti-microbial protection. Butt all joints tightly and seal all breaks and joints by adhering glass cloth tape,(on duct ) etc. Complete in all respects as per technical specifications

Fixing 19 mm thick 55kg/m3 density, regular closed cell class 0 nitrile rubber insulation finished with 7 mils factory laminated glass cloth ,anti-microbial protection. Butt all joints tightly and seal all breaks and joints by adhering glass cloth tape,(on duct ) etc. Complete in all respects as per technical specifications

Acoustic insulation

Supply of Acoustic lining inside sheet metal ducts with 10mm thick Open Cell nitrile rubber class 1,having density 140-180 kg/m3 insulation using manufacturers recommended adhesive with fire resistance as per BS 476 Part 7 and complete in all respects as per technical specifications

Installation ,testing and commissioning of Acoustic lining inside sheet metal ducts with 10mm thick Open Cell nitrile rubber class 1,having density 140-180 kg/m3 insulation using manufacturers recommended adhesive with fire resistance as per BS 476 Part 7 and complete in all respects as per technical specifications

Supply of Acoustic Insulation of AHU Rooms using open cell processed nitrile rubber having a density of 140-180 Kg/m3 and thickness of 25 mm with anti-microbial protection with suitable frame works etc. complete in all respects as required by the technical specifications

Fixing ,testing of Acoustic Insulation of AHU Rooms using open cell processed nitrile rubber having a density of 140-180 Kg/m3 and thickness of 25 mm with anti-microbial protection with suitable frame works etc. complete in all respects as required by the technical specifications.

AIR TERMINAL DEVICES

Supply of supply air grilles of extruded aluminium duly powder coated with suitable aluminium volume control damper etc. complete in all respects as per technical specifications

Fixing, testing and balancing of supply air grilles of extruded aluminium duly powder coated with suitable aluminium volume control damper etc. complete in all respects as per technical specifications

Supply of return air grilles of extruded aluminium duly powder coated without damper etc. complete in all respects as per technical specifications

Fixing, testing and balancing of return air grilles of extruded aluminium duly powder coated without damper etc. complete in all respects as per technical specifications

Supply of Supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. complete in all respects as per technical specifications

Fixing, testing and balancing of Supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. Complete in all respects as per technical specifications

Supply of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core . complete in all respects as per the technical specifications.

Fixing, testing and balancing of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core . complete in all respects as per the technical specifications.

Supplying of Linear Slotted Supply air diffusers of 3 slots, width 25 mm, powder coated aluminium complete in all respects as per technical specifications

Fixing testing commissioning of Linear Slotted Supply air diffusers of 3 slots, width 25 mm, powder coated aluminium with aluminium volume control devices etc. complete in all respects as per technical specifications .

Supply of Aluminium extruded exhaust air louvers with damper, bird screen etc. complete in all respects as per the technical specifications.

Fixing, testing and balancing of Aluminium extruded exhaust air louvers with damper, bird screen etc. complete in all respects as per the technical specifications.

Supply of Aluminium extruded fresh air sand trap louvers with bird screen etc. complete in all respects as per technical specifications

Fixing, testing and balancing of Aluminium extruded fresh air sand trap louvers with bird screen etc. Complete in all respects as per technical specifications

Supply of opposed blade type Extruded Aluminium volume control dampers of 16 gauge GI sheets to be provided with suitable links, levers and quadrants for manual control of volume of air flow and for proper balancing of the air distributions system complete in all respects as per technical specifications

Fixing, testing and balancing of opposed blade type Extruded Aluminium volume control dampers of 16 gauge GI sheets to be provided with suitable links, levers and quadrants for manual control of volume of air flow and for proper balancing of the air distributions system complete in all respects as per technical specifications

Supply of Fusible link type Fire damper for air distribution Networks, complete in all respects as per technical specifications

Fixing, testing and commissioning of Fusible link type Fire damper for air distribution Networks complete in all respects as per technical specifications

Inline Fans

Supply of Double Skin (Internally insulated ) Cabinet fans of 400 CFM-10 mm WG ESP minimum capacity with suitable blower, 3 phase/Single phase direct driven/Belt driven motor(IE3) of following capacity for exhaust, with Starter /Starter panel, with carbon filters, supports, vibration isolators, other accessories etc. complete in all respects as per the technical specifications

Installation ,testing & commissioning of Double Skin (Internally insulated ) Cabinet fans of 400 CFM-10 mm WG ESP minimum capacity with suitable blower, 3 phase/Single phase direct driven/Belt driven motor(IE3) of following capacity for exhaust, with Starter /Starter panel, with carbon filters, supports, vibration isolators, other accessories etc. complete in all respects as per the technical specifications

Supply of Double Skin (Internally insulated ) Cabinet fans of 550 CFM-10 mm WG ESP minimum capacity with suitable blower, 3 phase/Single phase direct driven/Belt driven motor(IE3) of following capacity for exhaust, with Starter /Starter panel, with carbon filters, supports, vibration isolators, other accessories etc. complete in all respects as per the technical specifications

Installation ,testing & commissioning of Double Skin (Internally insulated ) Cabinet fans of 550 CFM-10 mm WG ESP minimum capacity with suitable blower, 3 phase/Single phase direct driven/Belt driven motor(IE3) of following capacity for exhaust, with Starter /Starter panel, with carbon filters, supports, vibration isolators, other accessories etc. complete in all respects as per the technical specifications

Supply of Double Skin (Internally insulated ) Cabinet fans of 1500 CFM-15 mm WG ESP minimum capacity with suitable blower, 3 phase/Single phase direct driven/Belt driven motor(IE3) of following capacity for exhaust, with Starter /Starter panel, with carbon filters, supports, vibration isolators, other accessories etc. complete in all respects as per the technical specifications

Installation ,testing & commissioning of Double Skin (Internally insulated ) Cabinet fans of 1500 CFM-15 mm WG capacity with suitable blower, 3 phase/Single phase direct driven/Belt driven motor(IE3) of following capacity for exhaust, with Starter /Starter panel, with carbon filters, supports, vibration isolators, other accessories etc. complete in all respects as per the technical specifications

Air Curtains

Supply of 1 m wide air curtains for sliding doors. The system shall include all accessories including motors, blowers, door opening sensors,controllers,UPS Power & control cabling required, with necessary stainless steel structural support for installation complete in all respects. Material : SS Effective Throw: 2.4 m

Installation, testing and commissioning of 1 m wide air curtains for sliding doors. The system shall include all accessories including motors, blowers, door opening sensors, Power & control cabling required, with necessary stainless steel structural support for installation complete in all respects. Material : SS Effective Throw: 2.4 m

Dismantling of the following existing system: a.AHU/FCU b.CHW Pipe with Valve Packages inside AHU rooms c.Air distribution network with insulation d.UG CHW Pipe(Approx. 70m) along with supports etc. including leading and buying back complete in all respects as required by Engineer in charge.

FIRE PROTECTION SYSTEM Supply of 'C' class heavy duty GI pipe conforming to IS 1239 including fittings like elbows, tees, flanges, tapers, GI nuts and bolts, gaskets, suitable clamps and pipe supports, one coat of epoxy primer and two coats of synthetic enamel paint of required shade complete as required as per technical specification.

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Laying, testing & commissioning of 'C' class heavy duty GI pipe conforming to IS 1239 including welding, fixing the pipe on the wall/ceiling with suitable clamps, supports and painting with one coat of epoxy primer and two coats of synthetic enamel paint of required shade complete as required as per technical specification.

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Laying, testing & commissioning of 'C' class heavy duty GI pipe conforming to IS 1239 including welding, fixing the pipe inside trenches with suitable clamps, supports and providing and application of one coat of bituminous primer, providing anticorrosive wrapping coating 4 mm thick as per IS 10221, complete as required as per technical specification.

150 mm dia

80 mm dia

Supply of butterfly valve of following sizes having PN 16 rating conforming to IS 13095/API 609 with CI body, SS disc, EPDM/Nitrile rubber seal complete with GI nuts and bolts, gaskets, complete as required as per technical specification.

150 mm dia

100 mm dia

80 mm dia

40 mm dia

Installation, testing and commissioning of butterfly valve of following sizes having PN 16 rating with CI body, SS disc, EPDM/Nitrile rubber seal complete with nuts, bolts, washers, gaskets conforming to IS 13095/API 609, complete as required as per technical specification.

150 mm dia

100 mm dia

80 mm dia

40 mm dia

Supply of Standard response, standard coverage sprinkler, concealed pendant type sprinkler;1/2" NPT, K -5.6, operating temperature at 68 deg. C., including cover plate complete as required as per the technical specification.

Fixing, testing and commissioning of Standard response, standard coverage sprinkler, concealed pendant type sprinkler ;1/2" NPT, K -5.6, operating temperature at 68 deg. C. including cover plate, complete as required as per the technical specification.

Supply of Standard response, standard coverage sprinkler, upright type sprinkler ;1/2" NPT, K -5.6, Chrome Finish; operating temperature at 68 deg. C. complete as required as per the technical specification.

Fixing, testing and commissioning of Standard response, standard coverage sprinkler, upright type sprinkler ;1/2" NPT, K -5.6, Chrome Finish; operating temperature at 68 deg. C. complete as required as per the technical specification.

Supply of 1.0 m unbraided flexible drop to position the sprinkler head in desired location in suspended ceilings. The unit must be complete with stainless steel flexible drop with nipple, reducer, square bar and brackets etc complete as required as per the technical specifications.

Installation, testing and commissioning of 1.0 m unbraided flexible drop to position the sprinkler head in desired location in suspended ceilings with nipple, reducer, square bar and brackets etc complete as required as per the technical specifications.

Supply of gun metal fire hydrant valve ,single head oblique type with 63 mm instantaneous outlets with female socket for hose connection and inlet side with flange suitable for 80 mm pipe flange, valve conforming to IS:5290 complete with blank cap,chain etc as per technical specification.

Installation, testing and commissioning of gun metal fire hydrant valve ,single head oblique type with 63 mm instantaneous outlets with female socket for hose connection and inlet side with flange suitable for 80 mm pipe flange, valve conforming to IS:5290 complete with blank cap,chain etc as per technical specification.

Supply of First-aid Hose Reel with MS construction spray painted in Post office Red, conforming to IS 884 with up to date amendments, complete with the following as required as per technical specification. (a) 30 m. long 20 mm (nominal internal dia water hose Thermoplastic (Textile reinforced) Type-2 as per IS: 12585(b) 20 mm (nominal internal ) dia gun metal globe valve & nozzle. (c) Drum and brackets for fixing the equipments on wall. (d) Connections from riser with 25 mm dia stop valve (gun metal) & pipe.

Installation, testing and commissioning of First-aid Hose Reel with MS construction spray painted in Post office Red, conforming to IS 884 with up to date amendments, complete with the following as required as per technical specification. (a) 30 m. long 20 mm (nominal internal dia water hose Thermoplastic (Textile reinforced) Type-2 as per IS: 12585(b) 20 mm (nominal internal ) dia gun metal globe valve & nozzle. (c) Drum and brackets for fixing the equipments on wall. (d) Connections from riser with 25 mm dia stop valve (gun metal) & pipe.

Supply of 63 mm dia, 15 mtr. Long RRL hose pipe with 63 mm dia Male and Female Gun metal couplings duly binded with GI wire, rivets etc. conforming to IS 636 (type-A) as required as per technical specification.

Installation, testing and commissioning of 63 mm dia, 15 mtr. Long RRL hose pipe with 63 mm dia Male and Female Gun metal couplings duly binded with GI wire, rivets etc. conforming to IS 636 (type-A) as required as per technical specification.

Supply of 63 mm dia Gun metal branch pipe with 20 mm (nominal internal diameter) size Gun Metal nozzle conforming to IS 903, suitable for instantaneous connection to inter-connect hose pipe coupling as required as per technical specification.

Installation, testing and commissioning of 63 mm dia Gun metal branch pipe with 20 mm (nominal internal diameter) size Gun Metal nozzle conforming to IS 903, suitable for instantaneous connection to inter-connect hose pipe coupling as required as per technical specification.

Supply of hose boxes wall/pedestal type of size 750 x 250 x 600 mm made out of FRP with front side glass, locking arrangement and painted with approved colour completed as required and as per specifications.

Installation, testing and commissioning of hose boxes wall/pedestal type of size 750 x 250 x 600 mm made out of FRP with front side glass, locking arrangement and painted with approved colour completed as required and as per specifications.

Supply of 4 way Fire brigade collective breaching with 4 nos. of 63mm instaneous outlets with built in NRV and suitable for 150 mm flanged inlet connection with blank cap and chains etc complete as required as per technical specification.

Installation, testing and commissioning of 4 way Fire brigade collective breaching with 4 nos. of 63mm instaneous outlets with built in NRV and suitable for 150 mm flanged inlet connection with blank cap and chains etc complete as required as per technical specification.

Supply of Air release valve, 25 mm dia, complete as required as pet the technical specification

Installation, testing and commissioning of Air release valve, 25 mm dia, complete as required as pet the technical specification

Supply of UL listed/ FM approved flow switch with SPDT contacts, with fixing accessories suitable for nominal pipe dia meters ranging from 1" to 6". The body of the flow switch shall be water proof with IP protection. The flow switch should have minimum withstand pressure of 10Kg/cm2 complete as required as per the technical specification.

Installation, testing and commissioning of UL listed/ FM approved flow switch with SPDT contacts, with fixing accessories suitable for nominal pipe dia meters ranging from 1" to 6". The body of the flow switch shall be water proof with IP protection. The flow switch should have minimum withstand pressure of 10Kg/cm2 complete as required as per the technical specification.

EXTINGUISHERS

Supply of ABC Stored pressure type Fire Extinguisher 6 Kgs Capacity Mono Ammonium Phosphate based Dry Chemical Powder as per IS 14609 with ISI Mark for Fighting ABC Class of Fire, stored Pressure type of Mild steel body pressurized by Nitrogen Gas. The Extinguisher shall have pressure gauge for indicating inside pressure with opening and closing lever of squeeze grip type with tamper proof seal, complete with wall bracket. The Extinguisher should be manufactured strictly as per IS: 15683:2018 with ISI mark.

Installation of ABC Stored pressure type Fire Extinguisher 6 Kgs Capacity Mono Ammonium Phosphate based Dry Chemical Powder as per IS 14609 with ISI Mark for Fighting ABC Class of Fire, stored Pressure type of Mild steel body pressurized by Nitrogen Gas. The Extinguisher shall have pressure gauge for indicating inside pressure with opening and closing lever of squeeze grip type with tamper proof seal, complete with wall bracket. The Extinguisher should be manufactured strictly as per IS: 15683:2018 with ISI mark.

Supply of Carbon-dioxide extinguisher of ISI marked (IS: 15683:2018) 4.5 Kg capacity made of high pressure seamless steel cylinder (CCE marked ) complete with wheel type valve with one meter long braided high pressure discharge hose complete in all respects including initial fill with CO2 gas. complete as required as per the technical specification.

Installation of Carbon-dioxide extinguisher of ISI marked (IS: 15683:2018) 4.5 Kg capacity made of high pressure seamless steel cylinder (CCE marked ) complete with wheel type valve with one meter long braided high pressure discharge hose complete in all respects including initial fill with CO2 gas. complete as required as per the technical specification.

Supply of Modular(Ceiling mounted) ABC type extinguisher of 5Kg complete as required with all necessary accessories for successful operation as required as per the technical specification.

Installation of Modular(Ceiling mounted) ABC type extinguisher of 5Kg complete as required with all necessary accessories for successful operation as required as per the technical specification.

DETECTION SYSTEM

Supply of Addressable type Multi Detector (smoke & thermal) complete with all accessories like base, base box, etc. to be installed under/above false ceiling, roof and concealed space, interconnecting to loop cable, complete as required as per technical specification. The product shall be UL listed & FM Approved.

Installation, testing and commissioning of Addressable type Multi Detector (smoke & thermal) complete with all accessories like base, base box, etc. to be installed under/above false ceiling, roof and concealed space, interconnecting to loop cable, complete as required as per technical specification. The product shall be UL listed & FM Approved.

Supply of Addressable type Manual pull station (dual action type) enclosed in box with provision for cable or conduit coupling as required as per technical specification. The product shall be UL listed & FM Approved.

Installation, testing and commissioning of Addressable type Manual pull station (dual action type) enclosed in box with provision for cable or conduit coupling as required as per technical specification. The product shall be UL listed FM Approved.

Supply of wall mountable type sounder cum strobe for both audio and visual indication with all fixing accessories etc. and complete as required as per the technical specification. The product shall be UL listed & FM Approved.

Installation, testing and commissioning of wall mountable type sounder cum strobe for both audio and visual indication with all fixing accessories etc. and complete as required as per the technical specification. The product shall be UL listed & FM Approved.

Supply of fault isolator module to protect one area or a number of devices with complete set to be installed under/above false ceiling, roof, concealed space, wall, etc. interconnecting to loop cable complete as required as per technical specification. The product shall be UL listed & FM Approved.

Installation, testing and commissioning of fault isolator module to protect one area or a number of devices with complete set to be installed under/above false ceiling, roof, concealed space, wall, etc. interconnecting to loop cable complete as required as per technical specification. The product shall be UL listed & FM Approved.

Supply of wall mounted talk back unit for simplex communication of fire fighters with all necessary accessories complete as required as per the technical specification.

Installation, testing and commissioning of wall mounted talk back unit for simplex communication of fire fighters with all necessary accessories complete as required as per the technical specification.

Installation, testing and commissioning of UL listed & FM approved microprocessor based 10 looped, intelligent addressable main fire alarm panel, central processing unit with the loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, LCD display with touch screen or other keypad and events history log in the non-volatile memory (EPROM), power supply unit (230 ± 5% V, 50 Hz), 24 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall be networkable in peer-to-peer basis with other Addressable Fire Alarm Panels. The Panel shall be able to give pin point location of all Fire/Fault conditions of addressable units via the address codes for each unit. The Panel shall also be able to automatically switch off all Control Switches whenever any Alarm is triggered. The panel shall have facility to connect printer to printout log and facility to have provision to integrate with analog/digital voice evacuation system (PA System), talkback system and shall be complete with all accessories. The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as required as per the technical specification. a) Programming software for the system b) Automatic system test activates c) Detector sensitivity adjustments d) Alarm verification e) Alpha/numerical display f) Provision to connect to PCs and external printers The cost shall be inclusive of installation of suitable capacity UPS for the FACP.

Supply of intelligent addressable Input module for monitoring purpose and send the signal from a flow switch to the alarm panel for initiating alarm when flow occur, as per the technical specification. The product shall be UL listed & FM Approved.

Installation, testing and commissioning of intelligent addressable Input module for monitoring purpose and send the signal from a flow switch to the alarm panel for initiating alarm when flow occur, as per the technical specification. The product shall be UL listed & FM Approved.

Supply of addressable control to automatically trigger on/off devices like jet fans, AHU, extract air fans etc in case of fire. The product must meet technical specification. The product shall be UL listed & FM Approved.

Installation, testing and commissioning of addressable control to automatically trigger on/off devices like jet fans, AHU, extract air fans etc in case of fire. The product must meet technical specification. The product shall be UL listed & FM Approved.

Supply of 2x 1.5sq.mm armoured Copper FRLS cable ISI marked with proper clamping, supports and terminations appropriately above/below ground or on surface/in recess as required as directed by the Engineer-in-Charge.

Laying of 2x 1.5sq.mm armoured Copper FRLS cable ISI marked with proper clamping, supports and terminations appropriately above/below ground or on surface/in recess as required as directed by the Engineer-in-Charge.

Supply of 25mm dia PVC conduit along with accessories like PVC bends,couplers,junction box,fastners, iron staples/saddles/screws, in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit etc. and complete as required as per the technical specification.

Laying of 25mm dia PVC conduit along with accessories like PVC bends,couplers,junction box,fastners, iron staples/saddles/screws, in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit etc. and complete as required as per the technical specification.

DISMANTLING AND BUYBACK

Dismantling of existing detectors along with base, base box etc including leading and buying back complete in all respects as required by Engineer in charge

Dismantling of existing detector cable along with saddles and any other supports etc including leading and buying back complete in all respects as required by Engineer in charge

Dismantling of existing fire pipe line of diameters 150 mm, 100 mm, 80 mm along with supports etc including leading and buying back complete in all respects as required by Engineer in charge

Dismantling of existing hydrants and accessories along with supports etc including leading and buying back complete in all respects as required by Engineer in charge

SANITARY INSTALLATION Providing & fixing of star white vitreous China European wall hung pan with soft close seat and lid with CP brass hinges and rubber buffers with concealed cistern dual flush 3/9 litre water storage with chrome finish wall plate actuator etc complete, testing and commissioning to the satisfaction of Engineer in Charge as per direction of Engineer-In charge at all levels. (The purchase price (exclusive of all taxes, transporation and loading) of WC pan with soft close seat and lid including all accessories shall be taken as Rs 13336/- and concealed cistern, wall plate with flush button shall be Rs 4838/- and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.

Providing, fixing, testing and commissioning battery based infrared sensor operated Urinals, having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Purchase Rate for Urinals with sensor - Rs 58257 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing and fixing urinal partition made of 19mm thick both sides pre-polished approved marble of approved shade and sample with mirror polish to be fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in thechase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-incharge and finished smooth Overall size of finished marble partition shall be 550 x 1200mm. or as approved. The purchase price for italian marble (PA-ST-06) -Rs. 6190/- per Sqm, exclusive of all taxes, transporation and loading.

Providing, fixing, testing and commissioning of Table top Wash basin installed on existing counter with MS brackets, sensor tap, 15mm dia - 450mm long PVC connection pipe, one no 15mm dia CP angle stop cock with wall flange , 32 mm dia CP waste coupling, 32 mm dia CP brass bottle trap. The works shall include cutting and making good the walls and floors. The purchase price exclusive of all taxes, transportation and loading of WB is Rs13294/-, sensor tap- Rs 13377/-, angle valve - Rs 723/-, bottle trap- Rs 1772/- and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing, fixing and commissioning of CP brass hand spray with lever control (health faucet) of make 1meter long flexible tube and wall hook, CP brass one way angle valve and all fittings etc. angle valve should have inbuld pressure safety system complete, flexible corrugated stainless steel water connection pipe with all accessories complete ,15 mm dia 450mm long, testing and commissioning to the satisfaction of Engineer in Charge as per direction of Engineer-In charge at all levels. The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose. The purchase price exclusive of all taxes, transportation, loading of angle valve-Rs 723/-, Health Faucet - Rs 3566 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted) while making payment to the contractor).

Providing and fixing sanitary fixtures for handicapped toilet including one wash basin of approved size, one pair mounting brackets and all other related CP brass fittings like pillar cock, bottle trap,angle valve,waste coupling etc.One number EWC & Cistern with raised soft push button for convenient access complete with fittings & seat cover , one no.stainless steel hinged rail 76 cm & five nos. of stainless steel grab rails 60 cmetc of approved make as per drawing & as per manufactures specification .The rate is including cost and conveyance of all materials, labour charges, lead,lift,cutting and making good the walls,floors,slab wherever required etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in charge at all levels.The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.The purchase price(exclusive of all taxes) of handicapped toilet set is Rs 138897 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing and fixing tissue paper dispenser of approved quality and make including cost and conveyance of all materials labour charges ,lead, lift, ,cutting and making good the walls and floors wherever required as per direction of Engineer-Incharge at all levels(The purchase price(exclusive of all taxes) of tissue paper dispenser is Rs 3193 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing and fixing CP brass long body bib cock of approved quality and make conforming to IS standards and weighing not less than 690 gms including cost and conveyance of all materials, labour charges, sundries,lead,lift,cutting and making good the walls,floors,slab etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in charge at all levels. (The purchase price(exclusive of all taxes) CP brass long body bib cock is Rs.9392 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.

15 mm nominal bore

Providing and fixing frameless mirror of thickness 5.5 to 6mm, with all four edges machine polished/bevelled and back side protected with safety film and 4 mm thick BWP grade Plywood backing and fixed on walls with mirror screws(spacer). The rate is including cost and conveyance of all materials, labour charges, lead,lift ,cutting and making good the walls,floors,slab etc complete as directed by the Engineer-in-Charge at all levels.

Providing and fixing floor trap with cockroach trap (multi trap), , SS304 gradefloor grating with cup including cost and conveyance of all materials, labour charges, sundries etc completeas directed by the directed by the Engineer-in-Charge at all levels .(The purchase price(exclusive of all taxes)cockroach trap with floor gratings Rs 357 and PP multi floor trap is Rs.1300/- and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing and fixing under counter mounting pressmatic/ automatic liquid soap dispenser of approved make including cost and conveyance of all materials labour charges ,lead, lift, cutting and making good the walls, floors and slab wherever required etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in Charge at all levels .(The purchase price(exclusive of all taxes) of under counter mounting pressmatic/ automatic liquid soap dispenser is Rs3811 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.

Providing and fixing stainless steel A ISI 304 (18/8) sink of size 610x460mm bowl depth 250 mm without drain board or of approved size, 40mm CP brass bottle trap, CP brass waste coupling , CP brass sink cock with regular swinging spout with wall flange etc per IS: 13983 with C.I. brackets & stainless steel plug, including painting of fittings and brackets, cutting and making good the walls ,floors,slab wherever required,testing and commissioning to the satisfaction of Engineer in Charge:The rate is including cost and conveyance of all materials, labour charges, lead,lift etc complete as directed by the Engineer in charge at all levels.Purchase Rate for Sink - Rs 12678, sink cock - Rs 8017, angle valve-Rs 723/- (exclusive of all taxes, transporation and loading) and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing and fixing C.P. brass concealed stop cock (control valve) of standard design and of approved make conforming to IS:8931.The rate is including cost and conveyance of all materials, labour charges, lead,lift,cutting and making good the walls,floors,slab etc complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in charge at all levels.(The purchase price(exclusive of all taxes) of C.P. brass concealed stop cock (control valve) is Rs 4988 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 5 years and only skilled and experienced persons shall be employed for this purpose.

20 mm nominal bore.

Providing and fixing SS cleanout including cost and conveyance of all materials labour charges ,lead, lift, cutting and making good the walls and floors etc complete testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer in Charge at all levels.

75 mm dia

110 mm dia

Providing and fixing floor trap with cockroach trap (multi trap), concealed, SS304 gradefloor grating with cup including cost and conveyance of all materials, labour charges, sundries etc completeas directed by the directed by the Engineer-in-Charge at all levels .(The purchase price(exclusive of all taxes)cockroach trap with floor gratings Rs 918 and PP multi floor trap is Rs.1300/- and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing and fixing premium quality shower set consisting of overhead shower (square shape) single flow (body and face plate stainless steel with chrome finish) and hand shower oval shape single flow (ABS Body and face plate chrome plated) bathspout with single lever divertor with wall flange of approved make and model including cost and conveyance of all materials, labour charges, lead , lift etc., complete, testing and commissioning to the satisfaction of Engineer in Charge as directed by the Engineer-in-Charge at all levels. (The purchase price considered including all accessories for overhead shower , hand shower , for divertor,wall outlet is Rs 41390/- including all accessories any deviation plus or minus in the purchase price will be adjusted in the price quoted.)

Providing, fixing and testing water heater as per the instructions of the Engineer in charge at all levels(The purchase price(exclusive of all taxes)of water heater,6 litres is Rs 3330 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor).

Providing and fixing of stainless steel toilet paper holder including cutting and setting in walls with white cement joints and making good the wall. Purchase Rate to be Rs. 2004 per unit exclusive of GST, loading, transportation

Supply and Installation of Twin Robe Hook of approved design and make. Purchase Rate to be Rs. 956 per unit exclusive of GST, loading, transportation.

Supply and Installation of Soap Dish of approved design and make. Purchase Rate to be Rs. 1352 per unit exclusive of GST, loading, transportation.

Supply and Installation of Towel Rack of approved design and make. Purchase Rate to be Rs.4662/- per unit exclusive of GST, loading, transportation.

Providing and fixing water cooler of approved size and make 6,with storage capacity of 80 litres per hour and normal cooling capacity 40litres per hour with hot,cold and normal water provision with stainless steel body and seam welded stainless steel tank with adjustable cold water thermostat including mechanically expanded condensor,overload compressor protection,brass stainless steel coated water tap (3nos) with SS tray,aquaguard classic water purification system of capacity 1 litre per minute etc complete with all accessories of approved quality and make including cost and conveyance of all materials labour charges ,lead, lift, cutting and making good the walls,floors,slabs etc complete as directed by the Engineer in Charge at all levels.(The purchase price(exclusive of all taxes) of Stainless Steel Cooler of 80 litre capacity is Rs 58839and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 1 years and only skilled and experienced persons shall be employed for this purpose.

Providing and fixing floor mounted stainless steel A ISI 304 (18/8) sink of size 1200x600mm bowl depth450mm without drain board, CP brass waste coupling ,CP brass sink cock with regular swinging spout with wall flange(2 nos) etc per IS: 13983 with C.I. brackets & stainless steel plug, including painting of fittings and brackets, cutting and making good the walls,floors,slabs wherever required, testing and commissioning to the satisfaction of Engineer in Charge:The rate is including cost and conveyance of all materials, labour charges, lead,lift etc complete as directed by the Engineer in charge at all levels(The purchase price(exclusive of all taxes) of SS sink is Rs18222,CP brass sink cock(2 nos) is Rs 1101, waste coupling-Rs 370 and any deviation plus or minus in the purchase price of approved make will be adjusted (will be paid extra or deducted ) while making payment to the contractor). The above work shall be carried out by an agency having sufficient experience and should ensure a guarantee of 1 year and only skilled and experienced persons shall be employed for this purpose.

SANITARY WORKS Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in charge of PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows,unions, etc. with clamps and supports including cutting and making good the walls,testing the lines rectifying any leakages or defects,etc. complete for soil, waste, rain water,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for concealed work as directed by the Engineer- in-Charge.

110mm OD (6 kg/cm2)

75mm OD(6kg/cm2)

50mm OD(6 kg/cm2)

Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of PVC pipes with PVC specials such as tees, bends, door bend, door tee, elbows,unions, etc. with clamps and supports testing the lines rectifying any leakages or defects,etc. complete as directed by the Engineer-in-Charge for soil, waste, rain water,drains, vent pipe, etc. concealed or open at all levels including cost and conveyance of all materials, labour charges, sundries etc complete for internal work-exposed on walls as directed by the Engineer in charge.

160mm dia (6 kg/cm2)

110mm dia (6 kg/cm2)

Supplying, laying, jointing, testing and commissioning to the satisfaction of Engineer in Charge of hard PVC pipes with PVC specials such as tees, bends, door bends, door tees, elbows, unions, etc. with clamps and supports including earth work, refilling, testing the lines rectifying any leakages or defects, etc., complete as directed by the Engineer-in-charge for soil, waste, rain water pipe, etc. for underground lines

160mm dia (6 kg/cm2)

110mm dia (6 kg/cm2)

75mm dia (6 kg/cm2)

Supplying, fixing, testing and commissioning to the satisfaction of Engineer in charge of PVC gully trap of size 160 x 110mm and CI grating 150mmx150mm size and water tight C.I cover with frames 300mmx300mm size(inside) the weight of cover to be not less than4.5kg and frame to be not less than2.7kg (CI MH cover and frame as per IS:1726) single sealed of size conveying to size the above mentioned items and constructing 30cmx30cm internal size gully trap chamber and depth upto 60cm,115 thk brick wall in CM 1:6 on a foundation of PCC 1:4:8.100mm thick plastering inside with CM 1:3,12mm thk with a neat cement flushing coat and conveying to site,cleaning ,installing and testing approved make PVC gully trap with 160mm outlet(Fabricated),surrounding with CC 1:1.5:3, 150x150mmm,top with CI grating above the PVC gulley trap and light duty CI cover and frame over the chamber including cost of all materials, etc complete as per approved drawing and as directed by Engineer-in- Charge.

Providing and fixing PVC vent cowl to pipe already fixed as directed by Engineer-in-Charge at all levels.

110 mm dia

WATER SUPPLY WORKS Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps/supports at 1.00 m spacing.This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete.The rate is including cost and conveyance of all materials, labour charges, sundries,lead,lift,all taxes etc complete as per the direction of Engineer in charge at all levels.(Concealed work including cutting chases and making good the walls etc).

15mm nominal dia

32 mm nominal dia pipes

25 mmnominal dia pipes

20 mmnominal dia pipes

40 mm nominal dia pipes

Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl Chloride (CPVC- SDR11) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps/supports at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Internal work - Exposed on wall

80 mm nominal outer dia pipes

65 mm nominal outer dia pipes

50 mm nominal outer dia pipes

40 mm nominal outer dia pipes

32 mm nominal outer dia pipes

25 mmnominal outer dia pipes

20 mmnominal outer dia pipes

Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of Chlorinated Polyvinyl chloride(CPVC) SDR 11 pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipes with clamps/supports at 1.00 m spacing.This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete.The rate is including cost and conveyance of all materials, labour charges, sundries,lead,lift,all taxes etc complete as per the direction of Engineer in charge at all levels.(External Works)

80 mm nominal outer dia pipes

65 mm nominal outer dia pipes

50 mm nominal outer dia pipes

40 mmnominal outer dia pipes

32 mmnominal outer dia pipes

25 mmnominal outer dia pipes

20 mmnominal outer dia pipes

Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of gun metal gate valve with C.I. Wheel of approved quality (screwed end) including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels

80 mm dia nominal bore

65 mm dia nominal bore

50 mm dia nominal bore

40 mm dia nominal bore

32 mm dia nominal bore

25 mm dia nominal bore

20 mm dia nominal bore

Supplying, fixing, testing and commissioning to satisfaction of Engineer in charge of CI Gratings of approved quality including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer- in-Charge at all levels

Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 100mm

Supplying and fixing of CI double flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 100mm

Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 150mm

Providing and laying non-pressure NP3 class (medium duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete

300 mm dia R.C.C. pipe

150 mm dia R.C.C. pipe

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Dismantling of flushing cistern and water closet, wash basins,urinals,urinal partitions of all types (C.I./PVC/Vitrious China) at all levels including stacking of useful materials near the site and disposal of unserviceable materials within 5km lead as per direction of Engineer-in-Charge.

Dismantling G.I. pipes/C I/PVC/UPVC etc (external work) including excavation and refilling trenches in layers not exceeding 20cm in depth,consoldating each deposited layer by ramming and watering after taking out the pipes, manually / by mechanical means including stacking of pipes within 5km lead as per direction of Engineer-in-Charge:

Up to 150 mm diameter metre

Above 150 mm dia up to 300 mm dia metre

Above 300 mm diameter metre

Dismantling of C. I sluice valve including stacking of useful materials within a lead of 5kms lead as per direction of Engineer-in-Charge:

Upto 150 mm diameter

Above 150mm diameter

Providing and laying D.I. specials of class K-12 suitable for push-on jointing as per IS : 9523 : Up to 600 mm dia

Providing and laying D.I. Specials of Class K - 12 suitable for mechanical jointing as per IS : 9523 : Up to 600 mm dia

Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile IronPipes including testing of joints and the cost of rubber gasket :

200 mm dia pipes

150mm dia pipes

100mm dia pipes

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :

200 mm dia Ductile Iron Class K-9 pipes

150 mm dia Ductile Iron Class K-9 pipes

100 mm dia Ductile Iron Class K-9 pipes

Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints :

200 mm dia Ductile Iron Double Flanged

150 mm dia Ductile Iron Double Flanged

100 mm dia Ductile Iron Double Flanged

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :

200 mm diameter

150 mm diameter

100 mm diameter

Supply, laying & jointing in position HDPE pipes, including all fittings and accessories and suitable for the designed working pressures. This includes jointing of pipes & fittings as per the manufacturers specifications. The work has to be executed as per approved drawings and or as directed by Engineer - in Charge.- 90 mm-10kg/cm2

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

80 mm dia nominal bore

50 mm dia nominal bore

Providing and fixing CI Footvalve of approved quality as per the requirements of the Engineer in Charge

80mm dia

Providing and fixing enclosed type water meter (bulk type) conforming o IS : 2373 and tested by Municipal Board complete with bolts,nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :

100mm dia

150mm dia

Providing and fixing C.I. dirt box strainer for bulk type water meterwith nuts, bolts, rubber insertions etc. complete conforming to IS :2373 :

100mm dia

150mm dia

Description of Work / Item(s)

Amount

All inclusive Comprehensive Maintenance Contract for five years after two years DLP All inclusive Comprehensive Maintenance Contract for entire items covered under HVAC System of contract. Preventive Maintenance as per the recommendations of OEM and as per the technical specification and scope along with attending infinite number of breakdown maintenance calls for the entire system covered under this contract scope.

1st Year (after DLP)

2nd Year (after DLP)

3rd Year (after DLP)

4th Year (after DLP)

5th Year (after DLP)

All Inclusive Comprehensive Maintenance Contract for Five years after two years DLP All inclusive Comprehensive Maintenance Contract for remote sensing doors covered under this contract. Preventive Maintenance as per the recommendations of OEM and as per the technical specification and scope along with attending infinite number of breakdown maintenance calls for the entire system covered under this contract scope.

1st Year (after DLP)

2nd Year (after DLP)

3rd Year (after DLP)

4th Year (after DLP)

5th Year (after DLP)