CA NO. CWE BLY /GE(W)/88 OF 2021-2022 PROVN OF GUARD ROOM FOR 08 GUARDS ALONGWITH SCOOTER STAND AT GATE NO 2 OF HQ UB AREA UNDER GE(W) BAREILLY

Amount

Surface excavation n exc 30 cm deep and averaging 15cm deep and getting out soft/loose soil including clearing away all grass vegetation, saplings, shrubs, brushwood, roots, and trees n exc 30cm girth and removing rubbish out side of the defence land. etc complete all as specified and as directed

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil etc complete all as specified and as directed

Excavation over areas exc 1.5m but not exc 3.0m deep and getting out in soft/loose soil etc complete all as specified and as directed.

Excavation in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation or for shafts, wells, cesspits, manholes, pier holes, laying of under ground cable etc. n exc 10sq m on plan & getting out in soft/loose soil etc complete all as specified and as directed.

M & L for PCC 1:4:8 Type D2 using 40mm graded stone aggregate as in foundations, filling and mass concrete etc complete all as specified and as directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and as directed.

S&F Mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and as directed.

S&F for mild steel TMT bars 5mm dia. and over up to and including 10 mm dia. in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.9 mm dia or securing with clips quality confirming to complete all as specified and directed.

M&L brick work with fly ash old size bricks straight or curved on plan exc 6 m mean radius built in cm (1:6) complete all as specified and directed.

M&L brick work with fly ash old size bricks straight or curved on plan exc 6 m mean radius built in cm (1:4) for manhole and drain wallcomplete all as specified and directed.

M & L for half brick thick wall with fly ash bricks, in straight or curved on plan to any radius, built in CM 1:4 complete all as specified and as directed

M &L fo reinforced Cement concrete 1:2:4 Type B1(M-25) (Using 20 mm graded Stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M &L fo reinforced Cement concrete 1:2:4 Type B1 (M-25) (Using 20 mm graded Stone aggregate)) in Columns, pillars, piers, posts struts complete all as specified and directed.

M &L fo reinforced Cement concrete 1:2:4 Type B1(M-25) (Using 20 mm graded Stone aggregate)) in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified and directed.

M&L for reinforced Cement concrete 1:2:4 Type B1(M-25 (Using 20 mm graded Stone aggregate) in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M &L fo reinforced Cement concrete 1:2:4 Type B1(M-25) (Using 20 mm graded Stone aggregate) )in chajjas complete all as specified and directed.

M &L fo reinforced Cement concrete 1:2:4 Type B1(M-25) (Using 20 mm graded Stone aggregate) ) as in Fin/facia. complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, fair inished surface of conc. complete all as specified and directed.

Use and waste formwork to sides of pillars,posts, struts, piers, columns and stanchions fair finished surfaces of concrete complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc, fair finished surfaces of conc complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in fair finished flat surfaces of concrete complete all as specified and directed

Use and waste Formwork to chullah hoods, chajjas, troughs & similar items including edges complete all as specified and directed.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, as roughed finished surface of concrete complete all as specified and as directed.

S&F steel windows with pressed steel frame (size 95x45x1.25mm) side hung shutter including box type hinges with steel handle, and steel peg stay complete with glazed openable shutter with glazing bar(open out side) and wire gauged openable shutter without glazing bar(open inside), dovetailed or welded complete all as specified and directed and all as per Drg No TD/088 dt 07 Jan 2002 NOTE :- (i) Two shutter ie wire gauged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit. (ii) Rate for filling of PCC in frame deemed to be included in quoted rate. (iii) MS grill, glass and wire gauge shall be measured and paid separatly under relevant item of schedule

S&F Steel Ventilator with pressed steel frame with top hung glazed shutters and wire mesh shutter incl hinges with box handle, & steel peg stay, complete with glazing bars, dovetailed or weldedall complete all as specified and directedas per Drg No TD/088 dt 07 Jan 2002

S & F Pressed steel frames of size 125x60X1.60mm for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc; complete as specified

M&L for filling plain cement concret 1:3:6 type C0 (12.5mm graded aggregate) as in steel frame of door complete all as specified and as directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for 35mm thick 2nd class Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats etc complete all as specified and as directed.

M&L for 50mm x 47 mm size PVC solid door frame of size made out of 5mm plain Colour PVC sheet reinforced with MS square tube , supplying and fixing in opening as per specification and drawing shown in SSR 2020 Part II.complete all as specified and as directed.

M&L for 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain Colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain Colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain Colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing shown in SSR 2020 Part II.complete all as specified and as directed.

S&F Aluminium, anodised, barrel tower bolts 200mm long of extruded section.complete all as specified and as directed.

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section.complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy.complete all as specified and as directed.

S&F Aluminium handles 100mm size, cast type, anodised complete all as specified and as directed.

S&F Butt hinges 100mm size, medium weight, stainless steel complete all as specified and as directed..

S&F Sheet glass 3.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work complete all as specified and as directed.

M & L for Non-Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick Screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L machine cut kota stone slab flooring 18mm-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match to shade of the slab including rubbing and polishing over and including M&L for screed bed 20 mm thick in CM 1:4 as in floorscomplete all as specified and directed.

M&L machine cut kota stone slab skirting 18mm-20mm thick over and including cement plaster 10 mm thick in CM 1:3 laid and jointed with grey cement slurry mixed with pigment to match to shade of the slab including rubbing and polishing in vertical surfaces .complete all as specified and directed.

M&L glazed tiles 450x300x7 mm coloured on vertical surfaces, set and jointed in neat cement slurry and pointed in white or colour cement to mach over and including rendering 10 mm thick in CM 1:3 rough finish complete all as specified and directed.

M&L 10mm thick rendering as on celling concrete surfaces in cm (1:3) including finishing the surface even and smooth complete all as specified and directed.

M&L 12mm thick rendering cement plaster on other than fair faces of brick work or concrete surfaces but in cm (1:6) including finishing the surface even and smooth without using extra cement all as spd and directed

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in Cement plaster 1:4 finished even and fair complete all as specified and directed.

M&L 12mm thick rendering cement plaster on concrete surfaces in cm (1:3) including finishing the surface even and smooth without using extra cement mixed with WPC complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for preparation of new steel surface and applying two coats of synthetic enamel paint over and including one coat of red oxide primer over 10cm in width or girth complete all as specified and directed

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of cement primer complete all as specified and directed.

M & L for 100mm thick plain cement concrete 1:4:8 type D-2 using 40mm stone graded aggregate as in sub base to floor finished rough to receive finishes. complete all as specified and as directed.

Returning filling in soft/loose soil including spreading leveling watering and wall ramming in layers not exc 25 cm thick complete all as specified and directed.

Spreading & levelling in layers n exc. 25 cm thick & well ramming incl. watering as required complete all as specified and directed.

Removing excavated soil material exc 500m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M & L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate as in plinth protection including provn of 6mm wide construction joint at every 3.0m and change of direction filled with sealing compound complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Anti temite treatment of the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for Anti temite treatment of the top surface of filled earth at the rate of 5 litres of emlusion per sqm of surface area complete all as specified and directed.

M&L for Anti temite treatment of the soil under plinth protection at the rate of 5 litres of emlusion per sqm of surface area complete all as specified and directed.

M&L for Anti temite treatment of the soil alongwith external perimeter of building at the rate of 2.25 litres of emlusion per metre of the perimeter wall complete all as specified and directed.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing above 4.0 Kg/Sqm of make M/S IWL Ltd or equivalent as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be EMW FLATE of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions complete all as specified and as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with two coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

S&F 500 litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer ISI marked hoisted and fixed in position including 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. complete all as specified and directed

.S&F ( in repairs ) vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white with integral foot rest and cast iron 'P' or 'S' trap 100mm dia , front or back inlet including connection to flush pipe antisyphonage pipe etc including PVC low level 10 litre capacity valve less symphonic action type flushing cistern including brackets, 32mm dia PVC including concrete bedding and making good to floor complete all as specified and directed.

S&F vitreous China Urinal half stall type white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar 1:3 including PTMT spreader, PTMT waste coupling, PVC waste pipe complete all as specified and directed.

S&F 25 mm dia fancy type drappery curtain rod with brackets and PVC fancy type ends complete all as specified and directed.

S&F in repairs 15mm bore tubes medium grade galvanised with all new fittings and fixed to walls, ceilings or laid in floors etc and connections,and removal from site complete all as specified and directed.

S&Fin repairs, 20mm bore tubes medium grade galvanised with all new fittings and fixed to walls, ceilings or laid in floors/trenches and connections,and removal from site complete all as specified and directed.

S & F chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union size 125 mm complete all as specified and directed.

Supply and fix bib taps 15 mm bore chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F Stop valves 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F for 15 mm bore concealed stop cock fancy type, cast copper alloy chromium plated long shank and cup washers, crutch or butter fly handle, screwed down, screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F Wash hand basin vitreous China flat back 550x400mm size white, including PVC waste coupling 32mm size, PVC waste pipe 32mm bore, CP Pillar taps fency type , pair of brackets of mild steel 35 x 35 x 6mm size and PVC connection 450mm long complete all as specified and directed.

S&F CI soil waste and vent pipes 100 mm bore sand cast in any length with or without ears with cement joints laid in floors complete all as specified and directed

S&F CI soil waste and vent pipes 75mm bore size sand cast in any length with or without ears with cement joints laid in floors complete all as specified and directed

S&F CI soil waste and vent pipes 50mm bore size sand cast in any length with or without ears with cement joints laid in floors complete all as specified and directed.

S&F cast iron floor trap dia of outlet 75mm with grating including jointing to waste pipe and set in cement concrete 1:2:4 type B-1 complete all as specified and directed .

S&F 100 mm bore cast iron plain bend etc complete all as specified and directed.

S&F 75 mm bore cast iron bend etc complete all as specified and directed.

S&F 100 mm bore cast iron Junction single with access door/branch pieces, etc complete all as specified and directed.

S&F 75 mm dia cast iron Junction single with access door/branch pieces, etc complete all as specified and directed.

S&L 75 mm dia cast iron cowl etc complete all as specified and directed.

S&F Nipple 20mm bore suitable for HDPE water tank. (min. weight 20mm-45gms) etc complete all as specified and directed.

S&F Nipple 15mm bore suitable for HDPE water tank. (min. weight 38gms) etc complete all as specified and directed.

S&F 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight-210gms) etc complete all as specified and directed.

S&F 15mm bore brass gate valves,with iron wheel head,screwed both ends for iron pipes and fixed etc complete all as specified and directed.

S&F 20mm bore brass gate valves,with iron wheel head,screwed both ends for iron pipes and fixedetc complete all as specified and directed.

S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) etc complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 150mm bore pipes etc complete all as specified and directed.

M&L for SGSW drain pipes,bore of pipe150 mm bore,Grade 'A' in trenches and jointed in CM (1:1) with spun yarn and tested etc complete all as specified and directed.

S&F Salt glazed stone ware gulley traps 150x150mm size square mouthed type ‘P’ etc complete all as specified and directed.

M&L for construction of brick masonary septic tank for 10 users capacity using sub class B bricks old size, with and including necessary excavation, earth work, brick work, concrete work, plastering, returning filling in soft/loose soil and removal of surplus soil to a distance n exc 50 mtr etc complete all as shown in TD Drg No. 217 & specification complete all as specified and directed.

M&L for construction of soak well 1.2 metre dia and 3.0 metrer effiective depth with and including necessary excavation, earth work, brick work , plastering, filling with brick bats, PCC on top, returning filling in soft/loose soil and removal of surplus soil to a distance n exc 50 mtr etc all as shown in TD drg No. 309 & specification complete all as specified and directed.

M&L for Precast RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in precast cover slabs (for manholes etc.) including all use of forms, moulds or machine moulds and setting the blocks, slabs etc. in cement mortar (1:4) complete including necessory form work etc.all as specified and directed ( NOTE:-Reinforcement shall be measured and paid separately under respective item of this Schedule)..

.M&L for rubber moulded machine pressed precast cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of 80mm thickness, M-40 Grade. Approved design, shape, size and colour of top layer over and including M&L layer of 25 mm thick sand cushion including filling the joint with sand etc complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm cable PVC unsheathed and insulated copper multistranded conductor FRLS 1100 Volts grade cable (red colour cable to be used for live connection and black colour cable to be used for neutral connection) controlled by one way switch drown through and including PVC concealed conduit with all accessories including 1.0 sqmm copper multistrand conductor FRLS 1100 Volts grade unsheathed PVC insulated (green colour) continuity earth wire connected to common earth dolly and sunk cast pressed steel terminal box made out of MS sheet 1.25 mm thick for mounting of fittings like switch , socket and fan regulator with 3 mm thick hylum laminated sheet cover incl cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed for one light/fan/bell point controlled by one switch/bell push complete all as specified and directed.

All as per Sl.Item No100 above but One 5 Pin, 5 Amp, Switch Socket outlet point on idenpendent board.

All as per item No 100 here in before but for one 15 Amp 6 pin switch socket outlet independent with 2.5 sqmmm FRLS (Nominal area) PVC unsheathed copper conductor single core multistranded complete all as specified and directed.

S&F Switch, Piano, flush type, polycarbonate, 5 Amps, Single Pole, One way complete all as specified and directed.

S & F Socket outlet, polycarbonate, 2 in 1, 5 Pin,5 Amps, multipurpose, flush type complete all as specified and directed.

S&F Socket outlet, polycarbonate, 2 in 1, 6 pin, 5/15 Amps multipurpose, flush type complete all as specified and directed.

S&F Switch, Piano, flush type, polycarbonate, 15 Amps, Single Pole One way complete all as specified and directed.

S&F Ceiling rose, PVC polycarbonate, isolated body, 3 terminals, AC 230 volts complete all as specified and directed.

S&F Lamp Holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply& fixing in replacement of LED bulb 12 Watt 230 V AC integrated circuit complete all as specified and directed

S&F MCB, SPN 32 Amp 240 V, 'B' curve, 10 KA complete all as specified and directed.

S&F MCB, Single Pole, up to 40 Amps, 240 V, 'B' curve, 10 KA complete all as specified and directed.

Supply and fix flush Sheet Metal enclosure, SPN, DB, 8 Way with double door, IP-42 Protection, detachable gland plate, flush mounting for MCB fitted with bus bar, earth bar and neutral links complete all as specified and directed.

Supply & fix Surface Mounting LED, indoor decorative, PVC extruded T-5 batten, 20Watt, 4 feet long fitting including connection with 23/0.0076, three core, PVC flexible cable complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts,check nuts, nuts and washers of GI or steel all as shown in electrical plate No 3 of SSR-I connected to earth test point by means of nut, bolts and washers made out of galvanised iron or steel all including earthing pit in PCC (1:3:6) type C1,RCC (1:2:4) type B1 precast cover slab with one handle made out of 8 mm dia round bar,20 mm dia (medium grade) protecation pipe and providing layer of charcoal or coke and salt in alternative layers,necessary excavation & earth work in any type of starta complete all as specified including testng on completion complete all as specified and directed.

Supply and fix Security light fitting, LED type, 25 Watts, 6000 K, Pressure die cast housing with Prismatic Polycarbonate diffuser & individual LEDs as light source with integrated electronic driver complete with GI Pipe Mounting bracket of size 32mm dia and 1.20m long fixed to wall with and including nuts, bolts and GI clamps made out MS flat Iron of size 50x6mm as required including two coats of synthetic enamel over a coat of primer and making connection with three core 23/0.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed Cat No:- BCLST 20W LED manufactured by M/s Bajaj or equivalent model manufactured by M/s Philips/C&S.

S&F and testing ceiling fan of size 1200 mm 230V AC type including provision of new single core twin twisted cable from ceiling rose to ceiling fan connector all as specified and directed

Cutting existing pipe line for inserting 20 mm bore pipe including fitting complete all as specifed and as directed.

Supply, lay, joint, test and commisioning LT, XLPE insulated, screened, PVC bedded, armoured, heavy duty, electric cable with stranded aluminium conductor, 1100 Volts grade, cross sectional area 10 Sqmm, 2 core complete all as specified and directed. Note:-Excavation earthwork,sand cushioning & brick protection shall be measured & paid seperately.

M&L for dry river sand cushioning for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top ebdge of cable after laying and punning up to 18 cm depth complete all as specified and directed. Note ;- For payment purpose the punned down thickness of 18 cm only shall be considered.

Supply and laying bricks old size, well burnt sub class 'B' bricks as in protection cover for under ground cable laid width wise across the cable adjoining each other, laid dry complete all as specified and directed

R K CONSTRUCTION

Mohit Enterprises

SUBHASH CHANDRA AGARWAL

SANJEEV ENTERPRISES

M/S Shree Sai Builders

Jain construction co