CA NO.CWE BLY/GE (E)/21 OF 2025- 2026SPECIAL REPAIRS TO OTM BLDG NO T-102 AND T-26 OF 6 MTN DIV ORD UNIT AND OTM BLDG NO T-90 T-96 OR LIVING AND T-100 MI ROOM OF 883 BN ASC UNDER GE EAST BAREILLY

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling wooden truss/ scanteling purlin rafter etc. complete all as specified and directed.

S&F steel work in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410-W (Gde-E-250) quality-A etc complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws a on each sheet /each support rubber lining and filling of gap with cement mortar in CM 1:4 with wall and sheet up to 6 mtr height complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified and directed.

Taking down cement plaster of any thickness, raking out joints, hacking for key scrubbing down with water including terrazzo dado or wall finish such as tiles of any description and of any thickness, including for all necessary lowing etc, removal of rubbish of the premises; removal and depositing serviceable materials where directed and leaving the work clear for any type of plastering complete all as specified and directed.

M&L for 15 mm thick cement plaster in CM 1:6 on brick surface finished even and smooth without using extra cement including in patches complete all as specified and directed.

M&L for 15 mm thick cement plaster in CM 1:4 on brick surface finished even and smooth without using extra cement including in shafts, RCC chajjas, roof projections in four stories bldg in patches or as site requirements complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper using roller, brushes including in patches over a coat of alkali resistant primer and including 1.50 mm thick cement based wall care putty in two layer with making the surface complete smooth by rubbing etc with minimum 6 hr interval between and two coats complete all as specified and directed.

M&L for preparation of new surface of walls by vacuume based sanding machine; scrapping down smoke soot, moulds, moss and efflorescent salts and greays spots, removing nails etc. and applying two coats of exterior acrylic emulsion of any colour over one coat of exterior water based wall priming on walls with and including provision of scaffolding required for the treatment to external surfaces of building with all safety measure etc. complete all as specified and directed.

M&L for preparation of newly plastered surfaces at walls and applying the two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Complete removal of existing treatment from old brick/ concrete surface on walls and applying two coat of oil bound distemper using roller, brushes including in patches over a coat of alkali resistant primer and including 1.50 mm thick cement based wall care putty in two layers with making the surface complete smooth by rubbing etc with minimum 6 hr interval between any two coats complete all as specified and directed.

Complete removal of existing treatment on old surfaces by vacuume based sanding machine; scrapping down smoke soot, moulds, moss and efflorescent salts and greasy spots , removing nails etc, and applying Two coats of exterior Acrylic emulsion of any colour over one coat of exterior water based wall priming on walls with and including provision of scaffolding required for the treatment to external surfaces of building with required safety measures etc complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and iron of any description, over 10 cm in width or girth, not otherwise described include for all necessary preparatory work required and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F horizental level suspended ceiling comprising of rrmstrong GI Clip-in Micro perforated 600x600mm (nominal size) tiles of 120gsm/Sqm galvanised steel as per IS 277 (2003) suitable for architectural finishes in 0.5mm thickness as per in IS:513 (1994) in Global white colour with concealed suspension syayetm having a bevelled edge of 3x3mm and height of 33mm on one side and 18mm on other side. Tile shall have perforated of hole diameter 2.5mm and open area 16% with linear and diagonal pitch of 5.5mm and 7.7mm respectively along with a border of 10mm. The tile shall be electrostaticalkly polyster powder coated using RoHS compliant powder having coating thickness ranging from 60-80microns. Back side of the tile shall have Soundtex fleece hot pressed mechanically for uniform bonding to achieve NRC up to 0.7 all as per manufactures instructions complete all as specified and as directed. Note : If electrical cables are running at site and required to be relocated electric fittings on walls are required to be shifted including refixing of fan/ light fittings and other light accessory including making good the wall surface shall be deemed to be included to the rates.

M&L for false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of main runner 3600/3000 mm long, cross tee 1200 mm/ 600 mm long and wall angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c. The main runner to be placed @ 1200 mm. The cross tee 1200 mm will be inserted in the pre-cut slots of main runner at a regular interval of 600 mm to form a modular grid of 1200 mm x 600 mm. Additional cross tees of 600 mm shall be placed perpendicular to the cross tee 1200 mm long to finally form a grid of 600 mm x 600 mm. Grid of module size 600mm x 600mm shall be supported by 3/4 mm dia GI wire from purlins/ soffit. 4mm thick high pressure steam cured non asbestos fibre cement ceiling tile (density > 1200 Kg/Cum, modulus of rupture (M.O.R.)-10 MPa, Thermal conductivity (K)-0.02 W/mK) of size 595 mm x 595mm, confirming IS 14862 & Type B category III of ISO 8336:1993, (Reaction to fire-A2-s1-d0) tested as per EN13501 Part-I & BS-476 Part 4, 5, 6 & 7, should be placed in the grid module to form a false ceiling complete all as specified and directed.

Dismantling wall/ ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness complete all as specified and directed.

Dismantling unframed work timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of (un-reinforced) cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type B0 1:2:4 (12.5 mm graded stone aggregates) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for rough finished surfaces formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for preparation of newly or previously untreated of steel surfaces of any description, over 10cm in width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar includinguding all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with fly ash old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brushing cement slurry @ 3.00 Kg per Sqm on existing concrete surface complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B1 (20mm graded stone aggregate) as sub base complete all as specified and directed.

M&L for machine cut mirror polish uniform coloured kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for vetrified ceramic tiles 8-10 mm thick square of size exc 0.36 sqm but n exc 0.42 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No 32 but in vertical surfaces size n exc 0.36 sqm such as dado/ skirting over and including 10 mm thick rendering of cement mortar 1:4 complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed of cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per item No 34 but in vertical surfaces size n exc 0.36 sqm such as dado/skirting over and including 10 mm thick rendering of cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic tiles (300X 450 mm/ 300 x 600 mm), 7mm thick in vertical surface such as skirting, dados etc set and jointed in neat cement slurry and pointed in white or colour cement to match coloured tile over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for Granite (of any colour or any grains as approved) work with 16 to 18mm thick table rubbed and polished as in steps jambs , pillers , window cills, cooking platform and similar works including pointing in with cement using 1:2 using marbel dust and admixture of pigments to match with the shade of granite over and including 15mm thick screed bad in CM 1:6 for laying granite all as specified and directed including taking down / dismanteling of existing plaster/ stone of any type complete all as specified and directed. Note : Grinate shall be best quality and shall be provided one piece and width minimum 70mm in jambs except of cooking platform which shall be of full width as per site including full moulding of exposed edges with polishing complete all as specified and directed. The back surface of grinate shall be made rough by sprinkeling small pebbles using adehesive for bonding with bedding layer.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc. 4 Sqm each complete all as specified and directed.

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F 40 mm thick Factory made flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specified and directed.

M&L for 35 mm thick factory made glazed and skeleton shutters 2nd class HW, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, mitred and rebated sash bars any numbers. The size of rails & style as specified in SSR Part I (2009), Section 8, and as per IS-1003 (Part-I) Kiln seasoned as per IS-1141 and chemically treated as per IS-401 complete all as specified and directed.

M&L for powder coated aluminium sliding window with anodized aluminium frame of 3 Track of size 92mmx32mmx 1.5mm thick, with sliding shutters(02 glass and 01 Wirecloth) with necessary channels (top rail, bottom rail and style of size 40mmx 18mm x1.10 mm thick) including glazing with tinted sheet glass panel 4.00mm thick and Aluminum alloy wirecloth 4mm nominal dia and avg width of aperture 1.4mm, fitted with necessary jointing cleats, glazing clips,locking device one for each shutter , rubber packing, aluminium beading, screws, rawl plugs including all necessary holes / drilling etc complete all as specified and directed. Note : If mentioned section are not available in market, then immediate next higher section shall be provided by Contractor without any extra cost.

M&L for providing Aluminium shutter with Powder coated frame 88.9mm x 47.63mm x 1.60 mm thick fixed with heavy duty aluminium hinge of size 125mm and size of shutter with top rail , middle rail and bottom rail and style of size 85 mm x 44.5 mm x 1.56 mm thick with 200 mm size powder coated 2 nos with each leaf , Heavy duty powder coated aluminium tower bolt 150mm long 2 Nos per leaf, 3 nos Heavy duty aluminium powder coated of size 125mm with each leaf including 12 mm thick both side prelaminated particle board / 5.5 mm thick glass pane in the both panel with necessary joining cleats, rubber packing, aluminium beading, screws etc complete all as specified and directed. Note : If mentioned section are not available in market, then immediate next higher section shall be provided by Contractor without any extra cost.

S&F aluminium powder coated partitions with aluminium anodized frame of size 90mm x 44mm x 1.6 mm thick fixed with screws including panels of any 18/19mm thick decorative both side prelaminated perticle board inretior grade upto ht 1.80 mtr above tinted glass panels 5.5mm thick of ht 0.90 mtr , with necessary, jointing cleats, glazing clips, rubber packing, aluminium beading, screws etc. complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F 2nd class HW 35mm thick factory made Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats (Shutters shall be brought at site without primer and got approved by Engr-in-Charge/ GE.) complete all as specified and directed.

S&F 100 mm MS butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 150 mm aluminium anodised barrel tower bolts of extruded section, ISI marked complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S&F 300 mm long and Mild steel Chromium plated sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces complete all as specified and directed.

S&F mild steel spring 300mm for door, ordinary rat tail rod pattern springs, including roller and roller plate including welding as required for steel frame complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tracks or wooden beeding patti. complete all as specified and directed.

S&F in replacement curtain rod of CP MS 25 mm dia not less than 1.5mm thickness with chromium plated projected bracket both side as per sample fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw complete all as specified and directed.

M&L for cement concrete type C1 (1:3:6) (20 mm graded broken stone aggregate) 75 mm thick as in plinth protection and finish even and fair complete all as specified and directed.

M&L for forming construction joint 30mm deep x 10mm wide filled with sealing compound of Grade A complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound of Grade A complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block with gray cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade over 40mm thick sand cushioning including watering and consolidation complete all specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.

M&L concealed point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed Modular metal flush box of suitable size flush within wall surface, suitable for fixing of Modular cover plate, switches / sockets etc, complete all as specified and directed for the following :- Note : 1. Modular white cover plate shall be measured and paid separately 2. Rate quoted shall deemed to be inclusive of cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required complete all as specified and directed.

One Light point or one fan point controlled by one switch

One 3 pin socket outlet 5 Amp on same board

One 3 pin socket outlet 5 Amp on independent board

All as per item No 61 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and directed.

S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as specified and directed.

S&F Modular Socket 6 A, 5 Pin 2 Module size complete all as specified and directed.

S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as specified and directed.

S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as specified and directed.

S&F Modular white cover plate with frame, 3 Module size complete all as specified and directed.

S&F Modular white cover plate with frame,4 Module size complete all as specified and directed.

S&F Modular white cover plate with frame, 6/8 Module size complete all as specified and directed.

S&F Modular fan regulator step type complete all as specified and directed.

S&F angular lamp holder, metal cased body of brass with back plate including 09Watt LED Bulb in batten fittings, including Plastic square box of required size complete all as specified and directed.

S&F LED Bulb 9 Watt energy efficient color temp 6500k, lumen 825lm operating voltage 180-260 Volt complete all as specified and directed.

S&F ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in replacement LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and including control gear, GI bracket made from 32 mm bore dia light grade GI tube, size 1.50 mtr long etc, with and including making all electric connection complete all as specified and directed.

Taking down submain wiring of size 4/6 Sqmm complete all as specified and directed.

M&L for concealed sub main wiring with 2 runs of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC conduit of size 25 mm and above incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required complete all as specified and directed. Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two 2 runs of 6 Sqmm wire and one run of 6 Sqmm wire will be measured as one unit.

All as per item Ser No. 78 above but wiring with 4 Sqmm (3 Runs) complete all as specified and directed.

Taking down MCB Distributing board with MCCB/MCB of any size and capacity complete all as specified and directed.

S&F VTPN DB 12 way double door type IP 54 including MCCB TP 63 Modal DU 63D Amps as incomer complete all as specified and directed.

S&F sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint a complete all as specified and directed.

S&F sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint a complete all as specified and directed.

S&F SPN 40 to 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with X PM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 2009 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F in replacement AC functionnal box modular type complete with l enclosure with a 5/3 pin 16 Amp Socket and complete with one single pole MCB 20 Amp complete all as specified and directed.

Ikrar khan & co. (BID ID -3359091)

Shikhar ji Enterprises (BID ID -3359847)

MOHINDER SINGH AND SONS (BID ID -3359617)

Quality Builders (BID ID -3359559)

UTTRAKHAND BUILDERS (BID ID -3358999)