CECHZ/AMB/T-16/2021-22 PROVN OF DWCPE SEWAGE PIPE LINE AGAINT OLD VINTAGE NP 2 SGSW RCC SEWAGE PIPE LINE AND OTHER WORKS IN SECTOR C AND OTHER AREAS UNDER GE U AMBALA CANTT

Amount

ITEM NO. 1 : Excavation in trenches in soft/loose soil not exceeding 1.5 metre deep and not exceeding 1.5 metre wide for laying of cables, pipes foundation etc or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out including dressing/trimming sides and levelling/ grading and ramming of bottom of excavation complete all as specified and directed by Engineer-in-charge.

ITEM NO. 2 : Descripition all as per Serl item No 1 here-in-before but exceeding 1.5 metre deep but not exceeding 3.00 metre deep.

ITEM NO. 3 : Description all as per Serl Item No 1 here-in-before but in hard/denses soil

ITEM NO. 4 : Description all as per Serl Item No 2 here in before but in hard/denses soil

ITEM NO.5 : Excavation over areas, not exc 1.5 m deep and getting out as in soft/loose soil complete all as specified and directed by Engineer-in-Charge

ITEM NO.6 : Description all as per Serl Item No 5 here in before but depth exceeding 1.5 metre and not exceeding 3.00 metre deep.

ITEM NO. 7 : Description all as per Serl Item No 5 here in before but depth exc 3.00 metre and not exceeding 4.50 metre deep.

ITEM NO. 8 : Returning, filling in, including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each layer, complete all as specified and directed by Engineer-in-charge.

ITEM NO. 9 : Removing excavated surplus soil obtained from excavation to a distance not exceeding 250 metre and deposting where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engineer-in-charge..

ITEM NO.10 : Demolition of brick work or stone/boulder masonry built in cement mortar including all quions arches, pillar or any other description and in any situatoin etc complete all as specified and directed by Engineer-in-charge.

ITEM NO.11 : Demolition of cement concrete (reinforced) and (reinforcement cut as required to facilitate demolition) in any position not otherwise specificaly provided for complete and removing the unserviceable rubbish outside the MoD land complete all as specified and directed by Engineer-in-charge.

ITEM NO.12 : Demolition of Cement Concrete (Unreinforced Concrete) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-charge.

ITEM NO.13 : Concrete bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40 mm graded mechenically crushed stone aggregate complete all as specified and directed by Engineer-in-Charge.

TEM NO.14 : Concrete bed to drain pipes of 200 mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40 mm graded mechenically crushed stone aggregate complete all as specified and directed by Engineer-in-charge.

TEM NO.15 : Concrete bed to drain pipes of 250 mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40 mm grated mechanically crushed stone aggregate complete all as specified and directed by Engineer-in-charge.

ITEM NO.16 : H.D.P.E. Double Wall Corrugated(DWC) Pipes(ISI marked) 150 mm bore SN-8 Class as per IS 16098 part II for nonpressure Underground drainage and Sewerage applications with specials including cost of special O rubber ring couplers etc. , laid in trenches on concrete bed to level /gradient ,jointing with appropriate class fittings as per manufacturer's instructions including jointing accessories and fittings complete all as specified and directed by Engineer-in-charge.

ITEM NO. 17 : Description all as per Serl item No 16 here-in-before but DWC (Double Wall Corrugated) HDPE pipe 200 mm bore Class SN-8

ITEM NO. 18 : Description all as per Serl item No 16 here-in-before but DWC (Double Wall Corrugated) HDPE pipe class S N 8 of 250 mm bore

ITEM NO.19 : PCC 1:4:8 type C1, using 20 mm graded machnically crushed stone aggregates as in foundation filling and mass concrete complete all as specified and directed by Engineer-in-charge.

ITEM NO.20 : Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter for flat rough finished surfaces, complete all as specified and directed by Engineer-in-charge.

ITEM NO.21 : Use & waste of formwork to faces of walls,retaining walls, RCC circular manhols abutments,parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-charge.

ITEM NO.22 : Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings , slab over manholes similar work; not exceeding 200mm thick (Horizontal or sloping) (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-charge.

ITEM NO.23 : Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similarwork exc 10cm but n exc 20cm wide (rough finished surfaces of concrete), complete all as specified and directed by Engineer-in-charge.

ITEM NO.24 : TMT steel bars 10mm dia and over, of grade Fe-500D corrosion resistant steel (CRS) cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-charge.

ITEM NO.25 : TMT steel bars 6 to 8 mm dia and over, of grade Fe-500D corrosion resistant steel (CRS) cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-charge.

ITEM NO.26 : Reinforced cement concrete M-30(Design Mix) using 20 mm graded mechanically crushed stone aggregates as in foundation, including raft footings, foundation beams, plinth beams, bases for columns etc and mass concrete as in manholes complete all as specified and directed by Engineer-in-charge.

ITEM NO.27 : Reinforced cement concrete M-30 (Design Mix) using 20 mm graded machanically crushed stone aggregates as in walls, retaining walls,basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses as in manholes complete all as specified and directed by Engineer-in-charge.

ITEM NO.28 : Reinforced cement concrete M-30 (Design Mix) using 20 mm graded machanically crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, deck slabs and the like complete all as in manholes specified and directed by Engineer-in-charge.

ITEM NO.29 : Cutting into existing manholes for connecting new drains of 150mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4section) in cement concrete 1:2:4 mix type B-1, using 20mm graded mechanically crushed stone aggregate smooth finished and reforming benching as required for 150mm bore pipe complete all as specified and directed by Engineer-in-charge.

ITEM NO. 30 : Cutting into existing manholes for connecting new drains of 200 mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4section) in cement concrete 1:2:4 mix type B-1, using 20mm graded mechanically crushed stone aggregate, smooth finished and reforming benching as required of 200 mm bore pipe complete all as specified and directed by Engineer-in-charge.

ITEM NO. 30A : Description all as per Srl item no. 30 here-in-before but reforming benching for 250 mm bore pipe ---ditto---

ITEM NO.31: Cement concrete 1:2:4 type B-1 (using 20 mm graded machanically crushed stone aggregate) in surface channels and drains complete all as specified and directed by Engineer-in-charge.

ITEM NO.32 : Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed by Engineer-in-charge.

ITEM NO.33 : Supply and fix manhole cover SFRC(steel fiber reinforced cover) factory made of size 560 mm dia with and including suitable steel frame as per manufacturer's instructions , heavy duty as approved by GE complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.34 : Rolled mild steel sections( Fe-290W (Gde-E-165 quality-A)) as in stairs (framed) In flat,round or square bars including cleats, brackets,including embedding in concrete as in steps of manhole etc.complete all as specified and directed by Engineer-in-charge.

ITEM NO.35 : PCC 1:4:8, type D2,using 40 mm graded machanically crushed stone aggregates as in sub base, foundations,filling and mass concrete complete all as specified and directed by Engineer-in-charge.

ITEM NO.36 : Cement concrete (1:2:4) type B-1,using 20 mm graded machanically crushed stone aggregate 75 mm thick as in sub base of floors and pavings laid in alternative bays and making impresions of expanded metal while concrete in green. complete all as specified and directed by Engineer-in-charge.

ITEM NO.37 : 60 mm thick coloured precast concrete interlocking paver block of any shape and size,rubber moulded M-35 grade with grey cement and pigment to match, over and including 50 mm thick sand cushion complete, all as specified and directed by Engineer-in-charge.

ITEM NO.38 : 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints or jointed with solvent cement joint, laid in trenches or in floors,type B, conforming to IS 13592-1992 supplied laid , jointed & tested including taking out/down old pipes complete all as specified and directed by Engineer-in-charge. Note - Rubber rings for pipes and fittings shall conform to IS 5382-1985.

ITEM NO.39 :Brick work(Except bricks) using Old bricks straight or curved on plan not exceeding 6 Mtr means radius built in CM 1:4 complete all specified and directed by Engineer-in-Charge.(Bricks obtained from srl item No 10 shall be reused in this item)

ITEM NO.40 : Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces mixed with water proofing compound, including finishing the surfaces even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge. NOTE: Water proofing compound shall be measured and paid separately.

ITEM NO.41 : Supply only integral water proofing compound ISI marked complete all as specified and directed by Engineer-in-charge.

ITEM NO.42 : Providing cement concrete 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregate as in in lintels upto 1.5m clearspan, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete, all as specified and directed by Engineer-in-charge.

ITEM NO.43 : Pre cast cement concrete Grade M 30 using 20 mm graded mechanically crushed stone aggregate as in , cover slabs 100 mm thick (for man holes etc in three parts.) and similar articles complete, all as specified and directed by Engineer-in-charge.

ITEM NO.44 : Preparation of new wall surfaces and applying three coats of white wash on plastered/unplastered surfaces complete, all as specified and directed by Engineer-in-charge.

ITEM NO.45 :Preparation of new or previously untreated steel and iron surfaces of any description n exceeding 10cm in width or girth and applying two coats of anti corrosive piant over a coat of red oxide primer complete all as specified and directed.

Item No 46 : Blank

Item No 47 : Blank

ITEM NO.48 :Cutting existing road including premix carpet, WBM , hardcore and including making good road surface as per existing road specifications complete, all as specified and directed by Engineer-in-charge.

ITEM NO.49 : Taking up/down Cast Iron/Ductile Iron water mains ( including all fittings), from trenches, size of pipe 350 mm bore, complete all as specified and directed by Engineer-in-charge.

ITEM NO.50 : Taking up/down Cast Iron/Ductile Iron water mains ( including all fittings), from trenches, size of pipe 300 mm bore, complete all as specified and directed by Engineer-in-charge.

ITEM NO.51 : Taking up/down Cast Iron/Ductile Iron water mains ( including all fittings), from trenches, size of pipe 250 mm bore, complete all as specified and directed by Engineer-in-charge.

ITEM NO.52 : Taking up/down Cast Iron/Ductile Iron water mains ( including all fittings), from trenches, size of pipe 200 mm bore, complete all as specified and directed by Engineer-in-charge.

ITEM NO.53 : Taking up/down Cast Iron/Ductile Iron water mains ( including all fittings), from trenches, size of pipe 150 mm bore, complete all as specified and directed by Engineer-in-charge.

ITEM NO.54 : Taking up/down Cast Iron/Ductile Iron water mains ( including all fittings), from trenches, size of pipe 100 mm bore, complete all as specified and directed by Engineer-in-charge.

ITEM NO.55 : Supply, laying and testing of Ductile Iron Pipe of size 350mm bore with socket and spigot ends , class K 9, confirming to IS 8329/2000 in standard length of 5.5/6.0 metre, with inside cement mortar lining and outside metallic zinc sprayed with a finishing layer of bituminious paint including push-on- joints (Tyton joint) type and rubber gaskets of EPDM quality as per IS 5382 complete all as specified and directed by Engineer-in-charge .

ITEM NO. 56 : Description all as per Serl item No 55 here-in-before but Ductile Iron pipe of size 300 mm bore

ITEM NO. 57 : Description all as per Serl item no 55 here-in-before but Ductile Iron pipe of size 250 mm bore.

ITEM NO. 58 : Description all as per Serl item no 55 here-in-before but ductile iron pipe of size 200 mm bore.

ITEM NO. 59 : Description all as per Serl item no 55 here-in-before but Ductile Iron pipe of size 150 mm bore.

ITEM NO. 60 : Description all as per Serl item no 55 here-in-before but Ductile Iron pipe of size 100 mm bore.

ITEM NO.61 : M&L for DI fittings, externally coated with zinc rich paint and finishing layer of bituminious paint and with inside cement mortar lining, such as bends (any type, radus and angle), tapers any type ,(straight, bend, increasing,decreasing or double socket etc.), Tee pieces single branch, "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc of required size complete all as specified and directed by Engineer-in-charge.

ITEM NO.62 : Taking up/down existing old GI tubing 80 mm bore including all connections from trenches/walls/floors or any other situation complete all as specified and directed by Engineer-in-charge.

ITEM NO.63 : Description all as per Serl No 62 here-in-before but GI tubing of size 50 mm bore

ITEM NO.64 : Description all as per Serl No 62 here-in-before but GI tubing of size 40 mm bore

ITEM NO.65 : Description all as per Serl No 62 here-in-before but GI tubing of size 25 mm bore

ITEM NO.66 : Description all as per Serl No 62 here-in-before but GI tubing of size 20 mm bore

ITEM NO.67 : Galvanized steel water tubing 80 mm bore , medium grade with all fittings(such as bends,elbows,tees,short plugs and union etc) and fixed to walls / in chases and ceiling or laid in trenches including fixing complete all as specified and directed by Engineer-in-charge

ITEM NO.68 : Description all as per Serl item No 67 but Galvanised tubing of size 50 mm bore

ITEM NO.69 : Description all as per Serl item No 67 but Galvanised tubing of size 40 mm bore

ITEM NO.70 : Description all as per Serl item No 67 but Galvanised tubing of size 25 mm bore

ITEM NO.71 : Description all as per Serl item No 67 but Galvanised tubing of size 20 mm bore

ITEM NO.72 : Gun-metal, globe or gate valves, of 50 mm bore with iron wheel head screwed down high pressure, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-charge

ITEM NO 73 : Description all as per Serl item No 72 but Gun-metal globe or gate valve of 40 mm bore

ITEM NO 74 : Description all as per Serl item No 72 but Gun-metal globe or gate valve of 25 mm bore -

ITEM NO 75 : Description all as per Serl item No but 72 Gun-metal globe or gate valve of 20 mm bore

ITEM NO 76 : M&L for repair to existing 350 mm bore CI/DI pipe line- leakage by means of providing split type MS clamp of suitable size and dimensions made to shape and made out of MS Flat of size 75mmx10mm duly drilled holes at both ends and fixed with and including necessary nuts, bolts and washers of appropriate size in running water pipe line including necesary fittings/rubber insertion sheet to make the pipeline entirely leak proof complete all as specified and dirceted by Engr-In-Charge.

ITEM NO 77 : Description all as per Serl item No 76 here-in-before but for CI/DI pipe line of 300 mm bore

ITEM NO 78 : Description all as per Serl item No 76 here-in-before but for CI/DI pipe line of 250 mm bore

ITEM NO 79 : Description all as per Serl item No 76 here-in-before but for CI/DI pipe line of 200 mm bore pipe

ITEM NO 80 : Description all as per Serl item No 76 here-in-before but for CI/DI pipe line of 150 mm bore with clamp made out of MS flat of size 75mmx6mm.

ITEM NO 81 : Description all as per Serl item No 76 here-in-before but for CI/DI pipe line of 100 mm bore with clamp made out of MS flat of size 50mmx6mm.

ITEM NO 82 : Description all as per Serl item No 76 here-in-before but for CI/DI pipe line of 80 mm bore with clamp made out of MS flat of size 50mmx6mm.

ITEM NO. 83 :M & L for Repair to leakage of existing GI pipe line 80 mm bore by means of providing split type MS clamp of suitable size and dimensions made to shape and made out of MS Flat of size50mmx3mm duly drilled holes at both ends and fixed with and including necessary nuts, bolts and washers of appropriate size in running water pipe line including necesary fittings/rubber insertion sheet to make the pipeline entirely leak proof complete all as specified and dirceted by Engr-In-Charge.

ITEM NO.84 : Description all as per Serl item No 83 here-in-before but for GI pipe line of 50 mm bore

ITEM NO.85 : Description all as per Serl item No 83 here-in-before but for GI pipe line of 40 mm bore

ITEM NO. 85A :M & L for repair to leakage of existing CI pipe line 250 mm bore by means of caulkng of lead joint including providing lead in running water pipe line making the pipeline entirely leak proof complete all as specified and dirceted by Engr-In-Charge.

ITEM NO.85B : Description all as per Serl item No 83A here-in-before but for CI pipe line of 200 mm bore

ITEM NO.85C : Description all as per Serl item No 83A here-in-before but for CI pipe line of 150 mm bore

ITEM NO.85D : Description all as per Serl item No 83A here-in-before but for CI pipe line of 100 mm bore (Note for Srl Item No 76 to 85D :- The cost of Earth Work shall deemed be included in the unit quoted rate for this item)

EXTERNAL ELECTRIFICATION WORK

ITEM NO. 86 : Sand cushioning for cables 8 cm below the cable and 15 cm above the cable and punning down the sand to 18 cm thickness complete all as specified and directed by Engineer-in-charge. (Note: Only punned thickness shall be measured for payment purpose).

ITEM NO.87 : Burnt bricks with brick class designation 75 old size for cable protection laid adjacent to each other perpendicular to the direction of cable in trenches for protection of cables, complete all as specified and directed by Engineer-in-charge.

ITEM NO.88 : XLPE insulated, screened PVC bedded, galvanised wire armoured, electric power cable (heavy duty) earthed with aluminium conductor 11000 volts grade of cross sectional area 95 Sq mm 3 core laid in trenches/ducts/along poles/through pipes complete, all as specified and directed by Engineer-in-charge. Note:-Excavation, bricks for cable protection, sand cushioning , GI pipes and joints shall be measured and paid for seperately

ITEM NO.89 : Cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrinkable type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 to 95 sqmm complete all as specified and directed by Engineer-in-charge.

ITEM NO.90 : XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq mm 4 core laid in trenches/ducts/along poles/through pipes complete all as specified and directed by Engineer-in-charge. Note:-Excavation, bricks for cable protection, sand cushioning , GI pipes and joints shall be measured and paid for seperately

ITEM NO.91 : XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq mm 3.5 core laid in trenches/ducts/along poles/through pipes complete all as specified and directed by Engineer-in-charge. Note:-Excavation, bricks for cable protection, sand cushioning , GI pipes and joints shall be measured and paid for seperately

ITEM NO.92 : XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 95 sq mm 3.5 core laid in trenches/ducts/along poles/through pipes complete all as specified and directed by Engineer-in-charge. Note:-Excavation, bricks for cable protection, sand cushioning , GI pipes and joints shall be measured and paid for seperately

ITEM NO.93 : XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 120 sq mm 3.5 core laid in trenches/ducts/along poles/through pipes complete all as specified and directed by Engineer-in-charge. Note:-Excavation, bricks for cable protection, sand cushioning , GI pipes and joints shall be measured and paid for seperately

ITEM NO.94 : XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 150 sq mm 3.5 core, laying in trenches/ducts/along poles/through pipes,complete all as specified and directed by Engineer-in-charge. Note:-Excavation, bricks for cable protection, sand cushioning , GI pipes and joints shall be measured and paid for seperately

ITEM NO.95 : Cable jointing kit for 1.1 KV (Earthed) grade cable for outdoor type straight through heat shrinkable type joint complete with jointing material and accessories suitable for LT XLPE cable of size 3.5/4 core 25 to 50 sqmm cross sectional area complete all as specified and directed by Engineer-in-charge.

ITEM NO.96 : Cable jointing kit for 1.1 KV (Earthed) grade cable for outdoor type straight through heat shrinkable type joint complete with jointing material and accessories suitable for LT XLPE cable of size 3.5 core of 70 to 95 sqmm cross sectional area complete all as specified and directed by Engineer-in-charge.

ITEM NO.97 : Supply and fix Cable jointing kit for 1.1 KV (Earthed) grade cable for outdoor type straight through heat shrinkable type joint complete with jointing material and accessories suitable for LT XLPE cable of size 3.5 core of 120 to 150 sqmm cross sectional area complete all as specified and directed by Engineer-in-charge.

ITEM NO.98 : Galvanised Iron tubing light grade 40 mm bore laid in replacement for cable protection under the floors, road crossing, along the wall or along the pole including MS clamps, nuts, washers and bolts complete all as specified and directed by Engineer-in-charge.

ITEM NO.99 : Galvanised Iron tubing light grade 50 mm bore laid in replacement for cable protection under the floor, road crossing, along the wall or along the pole including MS clamps, nuts, washers and bolts complete all as specified and directed by Engineer-in-charge.

ITEM NO.100 : Galvanised Iron tubing light grade 80 mm bore laid in replacement for cable protection under the floor, road crossing, along the wall or along the pole including MS clamps, nuts, washers and bolts complete all as specified and directed by Engineer-in-charge.

ITEM NO.101 : Disconnecting and taking out under ground cable of any type and size from frenches floor, road, pole , pipe , wall etc complete all as specified and directed by Engineer-in-charge.

ITEM NO.102 : M&L for cutting of road/PCC footpath/ hardstanding /inerlocking tiles including excavation for laying cable/pipe and making good as per existing specification complete all as specified and directed by Engineer-in-charge.

NOTE- : Excavation and earth work for laying of DWC HDPE Pipes/DI Pipes/GI Pipes/ Cables/Cutting of manholes, roads , paths, walkways and any other work executed under this contract shall be carried out with utmost care and with all safety gears in place after obtaining permission from the respective authority. Any damage done while execution to any existing structure, pipe line, electric or communication cable shall be made good by the contractor exactly as per the existing specifications at his own cost. In case any deley caused by the contractor in making good the damage, demurrage as per norms or as decided by the GE is additionally chargeable to the contractor. Bailing ,pumping,timbering,planking and struting if required shall be carried out .The rates quoted by the contractor shall be deemed to be inclusive of these provisions.

Note: For the purpose of arriving at Contract Sum, the amount of credit of Rs 4,68,835.00 shall be deducted from the total amount arrived.

Sham Sunder Bansal