C/o Pacca Bharo to Lower Chalali via Banial Basti Km. 0/0 to 1/100 (SH providing and laying wearing G-III and premix carpet with seal coat in Km. 0/390 to 1/00 and repair of pot holes in Km. 0/0 to 0/390) under MMSY.

Repair to pot holes by removal of loose material, trimming of sides, cleaning of surface, then providing tack coat at the rate of 0.300Kg per square meter road surface with bitumen VG-10 followed 20 mm thick compacted pre-mix carpet using 1.46Kg of bitumen VG-10 and 0.027 cubic meter of crushed stone aggregate of proper grading per square meter of road surface mixed and heated to proper temperature in mix-all 6-10 tonne capacity rolled to desired density with 8-10 tonne weight static road roller followed by seal coat IRC type B using 0.68Kg of bitumen VG-10 and 0.006 cubic meter sand per square meter of road surface duly mixed and heated in mixall to the required temperature and property rolled after laying with 8-10 tonne weight static road roller to the desired density as per technical specification Clause 1904.2, direction of the Engineer-in-Charge. including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, or any other taxes imposed excluding GST by the Government.

Providing, laying, spreading by mechanically means and compacting to 75mm (seventy five millimeter) compacted thickness, stone aggregates of Grading-III, 53mm to 22.4mm (fifty three to twenty two point four millimeter) size to water bound macadam specification including spreading in uniform thickness, using template, hand packing motor grader, rolling with three wheeled roller 80-100 (eighty to one hundred) kN static weight in stages to proper grade and camber including applying and brooming stone screening type-B of size 11.2mm (eleven point two millimetre) nominal size at the rate of 0.18cum (zero point one eight cubic metre) per ten square metre to fill up the interstices of coarse aggregate, watering and compacting to the required density as per MORD Technical specification section 400 and as per entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, or any other taxes imposed excluding GST by the Government.

Providing and applying primer coat with bitumen emulsion (SS-I) on prepared surface of granular base including cleaning of road surface with hydroulic brooms and spraying primer with bitumen emulsion pressure distributor at the rate of 0.85 kg (zero point eight five kilogram) per square meter as per MORD Technical specification section 500, as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, or any other taxes imposed excluding GST by the Government.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kgs (Zero twenty five into Zero decimal three Zero kilogramme) per square metre on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, or any other taxes imposed excluding GST by the Government.

Providing, laying and rolling of open graded premix carpet of 20mm (twenty millimeter) thickness, composed of type-A 13.2mm to 5.6mm (thirteen point two millimeter to five point six millimeter) aggregates at the rate of 0.27 cum (zero point two seven cubic meter) premixed with bitumen binder Viscosity grade -Ten (VG-10(Ten) bitumen, at the rate of 14.6 kgs (fourteen point six kilogram) per 10 (ten) square meter of road surface, to the required line, grade and level to serve as wearing coarse on a previously prepared base including mixing in hot mix plant of 30/40 (thirty/forty) tonne per hour capacity transporting mixed materials with tipper and laying with paver finisher hydrostatic with sensor attachment and rolling with three wheeled 80-100 (eighty to hundred) kN static roller finished to required level and grades to be followed by seal coat of type-B complete as per MORD Technical specification clause 508 and as per the entire satisfaction and direction of Engineer-in-Charge excluding the cost of tack coat and seal coat but including carriage of materials with in all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, or any other taxes imposed excluding GST by the Government.

Providing and laying seal coat for sealing the voids in a bituminous surface laid to the specified levels, grade and cross falls using Type-B as per technical specification clause 510 using bitumen VG-10 (viscosity grade-ten) at the rate of 6.80kg (six point eight zero kilogramme) premixed with 0.06 (zero point zero six) cubic meter of fine aggregate per 10 Sqm. (Ten square meter) of road surface heated in mini hot mix plant and laying manually of mixed material and rolling with power road roller 80-100 (eighty to hundred) tonne capacity kN static roller, as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, or any other taxes imposed excluding GST by the Government.