Various Grants of Nagar Palika.

No. Description Name OF Work Amount

Providing, supplying and erection of Np3 450mm pipe

From Anand Chowkdi To Jakhli Tadav in Borsad.

Providing and Fixing of MS Grill on Bhobha Drain at

3 Schedule -B3 Construction of Compound Wall in FP 1801 at Borsad.

ESTIMATE FOR PROVIDING & ERECTING LED STREET LIGHT

4 Schedule -B4 AT VARIOUS LOCATIONS OF BORSAD NAGAR

ESTIMATE FOR PROVIDING & ERECTING LED STREET LIGHT

AT ICONIC APPROCH ROAD,BORSAD

1. Providing, Supplying & Erecting Street Light Pole with

6 Schedule -B6 LED Lights From Parswanath Complex Towards Rathod

Chowkdi at Borsad .

2. Providing, Supplying & Erecting Street Light Pole with

LED Lights From Batla Lake Towards Jain Derasar at Borsad

3. Providing, Supplying & Erecting Remaning Street Light

Pole with LED Lights From Anand Cross road to Bridge At

4. Providing, Supplying & Erecting Street Light Pole with

LED Lights At Tornavmata lake Road at Borsad .

1. PROVIDING OF FIRE FIGHTING SYSTEM AT CITY POINT

2. INSTALLATION OF FIRE FIGHTING SYSTEM AT SILVER

3. INSTALLATION OF FIRE FIGHTING SYSTEM AT F.P. NO.

Providing General Type Rain Water Harvesting System At

FP. No 138 Tp Scheme No. 2 At Borsad.

BORSAD NAGARPALIKA

NAME OF WORK :- Providing, supplying and erection of Np3 450mm pipe From Anand Chowkdi To Jakhli

Tadav in Borsad.

No. Description Quantity Total Per Amount

For 450mm dia. RCC NP3

1 Excavation for pipeline trenches for water supply,

sewerage line, manhole etc. incl. all with shoring and

struting if required as per required gradient and line

including safety provisions using site rails and stacking

excavated stuff including upto all required lead cleaning

the site etc. complete for all lifts and strata as specified.

In Hard Murrum, Boulders incl. macadam road. - Upto

In Hard Murrum, Boulders incl. macadam road. - 1.50 Mtr. -

2 Providing and supplying ISI Standard RCC Pipes (of Sulphate

Resisting Cement) in standard lengths of following class

and diameters suitable for either collar joints or rubber ring

joints including all taxes, insurance, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to departmental store, stacking etc. Note :-

One collar should be supplied with each full length plain

ended RCC pipe, cost included in rates below. One rubber

ring should be supplied with each full length socketed pipe,

cost included in rates below.

450 mm RCC NP3 Pipe 658.00 1361.00 Mtr.

3 Lowering, laying and jointing RCC pipes in C.M. 1:1 1/2 of

following diameters in proper position, grade and

alignment at all level as directed by engineer-in-charge

including conveyance from stores to site of work, labour,

giving hydraulic testing as per ISI code.

450 mm RCC NP3 Pipe 658.00 171.00 Mtr.

4 Refilling the pipeline trenches incl. ramming, watering,

consolidating, disposal of surplus stuff as directed within a

radius of 3 Km. 1823.05 22.00 Cu.M.

5 Providing and constructing sewer manhole, scraper

manholes and unit house connection chamber as per type

design in brick masonry in C.M. 1:5 and inside and outside

20mm thick plastering in C.M. 1:3 necessary 100mm coping

with reinforcement in R.C.C. N 200 fixing CI steps and fixing

manhole frame and cover(But excluding supply of manhole

frame and covers) over manholes and house connection

chambers and fixing manhole cover (but excluding supply

of manhole fram and covers) over scraper manhole etc.

complete as per latest CPHEEO manual.(excl Excavation).

( b) Manhole type "B" circular type having inside diameter

of minimum 1500mm and for depth beyond 1.5m to 4.0m

2. Extra Depth beyound 1.5m but upto 4M depth for Type

"B" as above.(12313 sRs Per Mtr rate total 2.0M) Total

6 R.C.C. precast manhole, frame and cover, manufacture,

supply and delivery at store or site of work precast R.C.C.

frame and cover (M200), suitable to drainage manhole and

as per type design and drawing including cost of

reinforcement, MS angles or flat, curing, mold work

> Frame 28.00 1121.00 Nos.

> Cover 28.00 1173.00 Nos.

7 water supply and sewerage pipe line repaing Work 1.00 10000.00 LS

Add 18 % GST :-

Add 2 % Contigency :-

BORSAD NAGAR PALIKA

Name Of Work:- Providing and Fixing of MS Grill on Bhobha Drain at Borsad.

No. Description Quantity RATE Per Amount

1 Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings and

frame alround, square or round bars with round headed bolts

and nuts or by screws (A) Plain Grill. 1,994.03 106.23 Kg

Applying priming coat over new steel and other metel surface

after and including preparing the surface by throughly cleaning,

oil,grease, dirt and other foreign matter and scoured with

brushes fine steel wood, scrapers and sand paper with ready

mixed priming paint brushing red lead. 77.80 36.93 SqM

3 Painting two coats (excluding priming coat) on new steel and

other metal surface with enamel paint, brushing, interior to give

an even shade including cleaning the surface an even shade

including cleanicn the surface of all dirt, dust and other foreign

matter. 77.80 92.20 SqM

GST 18% on R&B SOR Rate :-

3.00% Supervision & Contigency :-

BORSAD NAGARPALIKA

NAME OF WORK :- Construction of Compound Wall in FP 1801 at Borsad.

No. Description Quantity RATE Per Amount

Excavation for foundation upto 1.5 m depth including sorting out

and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(A) Loose or soft soil 215.85 117.08 Cu.M.

2 Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse

sand : 8- hand broken stone aggregates 40 mm nominal size) and

curing complete excluding cost of formwork in (A) Foundation and

Plinth 21.09 2680.21 Cu.M.

3 Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not exceeding

20 cm. in depth consolidating each disposited layer by

ramming and watering. 157.04 130.39 Cu.M.

4 Providing and laying controlled cement concrete M.200 and curing

complete including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in (A) Foundation &

Footing 37.73 4505.61 Cu.M.

Providing and laying controlled cement concrete M.200 and curing

complete including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in ( D ) Column 5.26 7975.97 Nos

Providing and laying controlled cement concrete M.200 and curing

complete including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in (C) Beams 37.21 5559.04 Sq.M.

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in superstructure above plinth

level upto floor two level in Cement Mortar 1:6 (1- Cement : 6 -fine

sand) (B) Conventional 23.72 4289.33 Cu.M.

8 20mm thick sand faced cement plaster on walls upto height

metres above ground level consisting of 12mm thick backing coat of

C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M.

1:1 (1-cement : 1-sand) etc. complete. 1096.47 335.65 Sq.M

9 Providing TMT Bar FE500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two

level 8773.07 76.21 Kg.

10 Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an

even shade including throughly brushing the surface free from

mortar droppings and other foreign matter and sand papered

smooth. 1096.47 78.90 Sq.M

11 Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings and

frame alround, square or round bars with round headed bolts and

nuts or by screws. (B) ORNAMENTAL GRILL 577.50 140.95 Kg.

12 Applying priming coat over new steel and other metel surface after

and including preparing the surface by throughly cleaning,

oil,grease, dirt and other foreign matter and scoured with brushes

fine steel wood, scrapers and sand paper with ready mixed priming

paint brushing red lead. 4.95 35.17 Sqm.

Painting two coats (excluding priming coat) on new steel and other

metal surface with enamel paint, brushing, interior to give an even

shade including cleaning the surface an even shade including

cleanicn the surface of all dirt, dust and other foreign matter. 4.95 87.81 Sqm.

Add 18.00% GST :-

3.00% Supervision & Contigency :-

BORSAD NAGARPALIKA

NAME OF WORK :- ESTIMATE FOR PROVIDING & ERECTING LED STREET LIGHT AT VARIOUS LOCATIONS OF BORSAD

NAGAR PALIKA,BORSAD

Description Quantity Total Rate Per Amount

Supplying & erecting Steel tubular pole (Swaged) confirming to IS - 2713 (Part-II)

Manufacturing process of steel tubular pole should be as per IS specification. Basic steel

tube should be ISI Marked. Pole should be painted by one coat of Zinc comet Primer

and two coat of Aluminium /approved paint to be erected on / in existing Foundation.

The length of poles are as below.

(i) pole as per IS code 410-SP-4 with 300 X 300 X 4 mm base plate. (Approximate Pole

weight 67 Kg) For burial erection

(ii) Add Extra for M.S. Base plate 300 X 300 X 16 mm for pole, Suitable for

mounting on surface of foundation with GI foundation bolts, with required

stiffeners welded with pole.

(iii) Add Extra for PU base primer and PU Paint on pole.

(A) 7.5 mtr. Long Swaged Steel tubular pole 162.00 8616.31 Each

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including

excavation for the pole of size 60 x 60 x 120 cm. Deep in below ground level with plinth

of 45 cm x 45 cm(or 45 cm dia x 45 cm) high upper ground level with necessary curing

and finishing in approved manner. ( for 7.5 & 8/8.5 mtr pole)

Providing and erecting Street Light pole bracket comprising main B Class MS pipe of

cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx.

45cms.length and suitable for 76.5 mm /80mm / required size of pole top having

sufficient fasteners for fixing the brackets and having spread of 1.5.mtr. length with

deg.with vertical plane & suitable welded stays, reducer and with check nuts complete

painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU

paint. paint with following nos of arms.

[1] Single Arm Bracket 1.5 Mtr 162.00 683.77 Each

Supplying and erecting LED street light / Flood light fittings with High power White LEDs

wattage of 3Watt and above assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser and Polycarbonate

optics/ lenses with company mark/name engraved or embossed 160 to 300 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K, Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt. LED driver efficiency > 85 %.CREE / OSRAM /

PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make LED used for luminaire.

(fittings required LM-79 & LM-80 certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.

(A) Street Light (IP-65), Surge protection -4KV integral and 10 kv non integral ,Light must

have 440VAC line supply protection. It should withstand 48 hours for 440VAC line

supply. (c) above 48 to 60 watts Cat-ll 162.00 4106.00 Each

Providing & erecting approved make street light / wall mounting junction box

compression moulded from SMC (thermoset plastic) vertical sliding cover having locking

with square head stud loop in / loop out in built terminal suitable for four core cable,

waterproof of I.P. 54 protected with clamp or bolt nut & earth bolt of following size.

[A] 200mm x 127mm x 83 mm Size 162.00 356.53 Each

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve)

having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following

capacity (A) 6 to 32 Amp.

Cat.-II 162.00 270.68 Each

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be

erected as directed of following size.

(A) 2 core 2.5 Sq.mm 1701.00 99.99 RMT

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench /

pipe at road crossing or floor of following size of cables.A1) 4 core 10 Sq. mm,

“B” class Galvanised iron pipe having smooth finished bore of the pipe on both ends

erected nuts and bolts along the pole / wall shaping the pipe as per site requirement.

Pipe dia as following.

(c) 40mm dia. 243.00 249.47 Each

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia.

galvanised iron pipe with coupling and buch buried in specially prepared earth

pit complete with necessary 8 SWG earth wire.

For using salt and charcoal / coke as required for pipe type earthing. 162.00 171.70 No

Supplying & erecting in earthpit of minimum bore dia. 225mm size approved

make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate including value of

earth resistane of installation

[C] For Electrical Installation covering Transformer Neutrals, Lightning

arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation,

SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft

Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg 6.00 10593.89 No

Making trench in Hard Murrum / Tar Road of suitable width of 90 cms or

required depth for laying any size of cable or locating the fault all over the run

and back filling the same and making the surface as normal ground.

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or

required depth for laying any size of cable or locating the fault all over the run

and back filling the same and making the surface as normal ground. (B) If

additional machinery like hammer driller or JCB use [Add]

Providing and, fixing heavy duty flange type brass cable gland with rubber ring

for PVC insulated armoured cable complete with out going tails, insulating tape

etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm 648.00 38.38 No

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene (conforming to IS 14930 II) with necessary connecting accessories of same

material at required depth for laying of cable. below ground / road surface for enclosing

cable and back filling the same to make ground as per original.

Supplying & erecting IP 55 grade following size section pillar fabricated from joint less

M.S. Sheet with angle iron legs made from jointless M.S. Angle with cable clamps to be

buried in ground to have appropriate erection to work uniform until erected with

cement concrete foundation and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side, with internal and outside looking

arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one

is welded and other with nut and bolt for erecting Bakelite sheet. Painting the Section

Pillar inside and out side with three tank powder coated paint. section pillar roof

should be without joint with water leakage proof & tested as per IP 55 test & followed

by IS 2147 of 1962 (C) 60 X 30 X 45 cm section pillar fabricated from 16 Gauge MS Sheet

with angle iron legs 45 cm long made from 35 X 35 X 5 mm thick MS angle.

Supplying & erecting approved make Digital time switch having lithium cell 6 years

operative and operate battery backup 1 channel day clock with 14 memory programme,

suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup

time 1 minimum & LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure & transparent

cover erected as required with necessary connection erected as directed.

Approved make Four pole moulded case circuit breaker having breaking capacity ICU of

25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed thermal &

magnetic release suitable to work on A.C. supply 50 c/s. with all internal connections &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only - Cat III 162.00 6173.12 No

Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC

Supply 500 V on existing panel board with necessary connections.

Supplying and erecting approved make panel mounting type Digital Ammeter

having 3 digits LED display, external CT operated, calibrated for 0 to

Amps suitable to operate on 500 Volt AC , erected on existing panel board with

all connection, wiring etc .with manufacturers calibration certificate.

Supplying and erecting approved make panel mounting type Digital Voltmeter

having 3 digits LED display, 0 to 750 AC Volts range erected on existing panel

board with all connection, wiring etc .with manufacturers calibration certificate.

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5

ratio 15 VA burden erected in existing CRCA box duly secured with insulating

materials connected to the meter 6.00 274.72 No

Supplying and erecting approved make suitable panel indicator lamps of LED type lamp,

lens cover, Bakelite holder complete erected with necessary connections.

Pro. & erecting electronic overload relay with single phasing preventer [ (L&T, Alstom,

BCH,T.C., Siemens, C&S make).

Providing and erecting AC-3 duty 3 pole power contactor with 2 NO & 2 NC aux contacts

complete with 415V/220V operating coil suitable for (L&T, BCH,T.C., Siemens, C&S

(a) for 25 / 32 A rating 6.00 3800.00 No

BORSAD NAGAR PALIKA

NAME OF WORK : ESTIMATE FOR PROVIDING & ERECTING LED STREET LIGHT AT ICONIC APPROCH ROAD,BORSAD

No Description QTY. Per Amount

LED DECORATIVE POLE MODEL - 1764 - CLASSIQUE 7.5 MTR DOUBLE ARM

BRACKET DECORATIVE POLE WITH PU PAINTPIPE SIZE - 150X150X3.5MM AND

580D,3MM BASE PLATE SIZE 300x300x16 MM Light Colour

3000K/4000K/6000K MATERIAL TYPE- MS Powder Coated approves by Nagar

1 Palika Engineer.

LED DECORATIVE POLE MODEL- 1764 - CLASSIQUE 7.5 MTR TRIPLE ARM

BRACKET DECORATIVE POLE WITH PU PAINTPIPE SIZE- 150X150X3.5MM AND

58OD, 3MM BASE PLATE SIZE - 300X300X16MM LIGHT COLOUR -

3000K/4000K/6000K MATERIAL TYPE- MS Powder Coated approves by Nagar

2 Palika Engineer.

Supplying & erecting approved make SMC

press moulded composite FRP. loop-in, loop-out approx. 2mm thick box

complete With Bakelite connector strip hWay(3P+N+E),DIN rail for mounting

mob & hinged doors as per requirement havinglocking arrangements with

mounting clamp With nuts, bolts & washers suitable for erection on pole with

cable Clamps& earth bolt of following size of box.(a) 300ww zooms x 100mm

Supplying and erecting LED street iign / Flood light fittings with High power

White rED• wattage of 3 Watt Supplying and erecting LED Street Light/Flood

Light Fitting with High Power White LEDs Wattage of 3 Watt and Above

assembled on single MCPCB, efficiency

more then130 Im/w and corrosion free

high Pressure die cast aluminum housing with smoOth finish powder coated

and heat Sink extruded aluminium with diffuser and Polycarbonate

optics/lenses, with toughened glass with compmark/name engraved or

embossed 160 to

270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.4S, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have

›hown ranges of Wattage capacity of LED âttings.The Engineer incharge may

select any wattage capacity between the rangesShown.)

(A) Street Light (IP-65), Surge protection -4KV integral and 10 kv non integral

,Light must have 440VAC line supply protection. It should withstand 48 hours

for 440VAC line supply. (c) above 60 to 90 Wattes Cat iii

Supplying and erecting Flexible PVC insulated multi strand multi core

1.1 kv grade ISI marked copper wires of following size to be erected as

(e) 1.50 Sq.mm 3 core round PVC sheathed 1540 31.31 RMT

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following

6 size of cables

(A) 4 core 16 Sq. mm 1190 153.52 RMT

R&B SOR 25-26 ELE No:4-3-5

Supplying and erecting B class Galvanized iron pipe having

smooth finished bore of the pipe on both ends erected nuts and

bolts along the pole / wall shaping the pipe as per site

7 requirement. Pipe dia as following.

(C) 40 mm dia. 70 249.47 RMT

Providing and erecting Pipe type earthing having 150 cms.long

and 2.5 cms. dia. galvanised iron pipe with coupling and buch

buried in specially prepared earth pit complete with necessary

8 SWG earth wire.

For using salt and charcoal / coke as required for pipe type

Supplying & erecting in earthpit of minimum bore dia. 225mm

size approved make Safe Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 80 mm having 80-200

Micron galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following

type of applications with chamber and heavy duty cover

(A)(approved make OEM has to submit test certificate including

value of earth resistance of installation duly stamped and signed

by agency and officer Incharge has to ensure the value of

earthing resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be

capable to retain moisture for long time Necessary test report

must be submitted by Agency.

Making trench in Hard Murrum / Tar Road of suitable width of

cm or required depth for laying any size of cable or locating the

fault all over the run and back filling the same and making the

11 surface as normal ground.

Making trench in Hard Murrum / Tar Road of suitable width of

cm or required depth for laying any size of cable or locating the

fault all over the run and back filling the same and making the

12 surface as normal ground.

(B) If additional machinery like hammer driller or JCB use [Add]

Providing & laying approved make Double walled corrugated

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth in existing trench for laying of cable. below ground /

road surface for enclosing cable 50 MM Oute Dia

Providing and fixing Terminal board of size 5.0 x 127 x

mm.bakelite sheet with suitable brass studs with nuts, washers

and clamps of size 25mm x 3mm suitable for pole painted with

14 one coat of red lead paint.

Providing 1:2:4 cement concrete foundation & 70 % PCC from

bottom including excavation for the pole of size 60 x 60 x

cm. Deep in below ground level with plinth of 45 cm x 45 cm(or 31 137.36 Cmt

45 cm dia x 45 cm) high upper ground level with necessary

curing and finishing in approved manner.

15 ( for 9 & 10 mtr pole)

Providing and, fixing heavy duty flange type brass cable gland

with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of

(B) 2 to 4 core 6 Sq. mm 124.444 38.38 Nos

(D) 2 to 4 core 16 Sq. mm 62.2222 47.47 Nos

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

Supplying & erecting IP 55 grade following size section pillar

fabricated from joint less M.S. Sheet with angle iron legs made

from jointless M.S. Angle with cable clamps to be buried in

ground to have appropriate erection to work uniform until

erected with cement concrete foundation and 45 cm high bricks

work finishing with plaster etc. hinged double door internally

supported on both side, with internal and outside looking

arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S.

Angle of Two Nos. one is welded and other with nut and bolt for

erecting Bakelite sheet. Painting the Section Pillar inside and out

side with three tank powder coated paint. section pillar roof

should be without joint with water leakage proof & tested as per

IP 55 test & followed by IS 2147 of 1962 (C) 60 X 30 X 45 cm

section pillar fabricated from 16 Gauge MS Sheet with angle iron

legs 45 cm long made from 35 X 35 X 5 mm thick MS angle.

(A) 150 X 90 X 75 cm section pillar fabricated from 14 Gauge MS

Sheet with angle iron legs 95 cm long made from 40 X 40 X 6 mm 1 16691.26 Ea

thick MS angle.

Supplying and erecting HYLAM sheet on existing angle iron

19 frame.for following thickness

Supplying & erecting approved make Digital time switch having

lithium cell 6 years operative and operate battery backup

channel day clock with 14 memory programme, suitable to

operate on 240V + 5%, 16A with, floating contacts Minimum

switching setup time 1 minimum & LCD display. Also comprised

permanent ON/OFF switching. Programming switches & housed

in fire proof thermoplastic enclosure & transparent cover

erected as required with necessary connection erected as

Supplying and erecting Ammeter / Voltmeter selector switch for

phase AC Supply 500 V on existing panel board with necessary

21 connections.

Supplying and erecting approved make panel mounting type Digital

Ammeter having 3 digits LED display, external CT operated, calibrated

for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

Supplying and erecting approved make panel mounting type Digital

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected

on existing panel board with all connection, wiring etc .with

23 manufacturers calibration certificate.

Providing & erecting L.T. Current Transformer with bar primary 50/5

to 1000/5 ratio 15 VA burden erected in existing CRCA box duly

24 secured with insulating materials connected to the meter

Supplying and erecting approved make suitable panel indicator lamps of LED

type lamp, lens cover, Bakelite holder complete erected with necessary

25 connections.

Providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply

c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

Cat III 1 6173.12 Ea

providing and erecting Miniature circuit breaker single pole 0.5A

to 2A system and having breaking capacity 10 KA to be erected

in existing box. confirming to IS 8828/1996 with ISI Mark

Cat iii 31 270.68 Ea

Providing & erecting 415V MCB Four Pole Switch for Lighting

Load (B curve) having 10KA breaking capacity & confirms to IS

:8828 in existing box having following capacity

(a) 6 to 32 Amp.Cat lll 1 573.00 Ea

3.00% Supervision & Contigency :

BORSAD NAGARPALIKA

1 Providing, Supplying & Erecting Street Light Pole with LED Lights From Parswanath Complex Towards Rathod Chowkdi at

Providing, Supplying & Erecting Street Light Pole with LED Lights From Batla Lake Towards Jain Derasar at Borsad .

Providing, Supplying & Erecting Remaning Street Light Pole with LED Lights From Anand Cross road to Bridge At Borsad

Providing, Supplying & Erecting Street Light Pole with LED Lights At Tornavmata lake Road at Borsad .

1 Providing, Supplying & Erecting Street Light Pole with LED Lights From Parswanath Complex Towards Rathod Chowkdi at

No Description Quantity Total Rate Per Amount

1 Providing decorative Single arm street light with 7.5mtr Steel tubular

pole (Swaged) confirming to IS - 2713 (Part-II) 1980 and bracket with

1500mm width and 750mm total height with suitable insertion pipe

diameter as per attached drawing with vertical plane & suitable

welded stays, reducer and with check nuts complete painted with one

coat of Red oxide / PU base primer and two coats of Aluminium / PU

paint. paint with following nos of arms. including M.S. Base plate 300 X

300 X 16 mm for pole, Suitable for mounting on surface of foundation

with GI foundation bolts,with pole required stiffeners welded also

Including LED IP-65 Light CCT-5000k Driver Efficiency - 85% Fitting As

Per Approved Bracket Design by Nagar Palika.

Supplying & erecting approved make SMC press moulded composite

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.

(B) 250mm x 200mm x 100mm [deep] 27.00 515.10 Nos.

4 Supplying and erecting Flexible PVC insulated multistrand multicore

1.1 kv grade ISI marked copper wires of following size to be erected as

e) 1.50 Sq.mm 3 core round PVC sheathed 594.00 31.31 Rmt.

5 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

(A) 4 core 16 Sq. mm 1076.00 153.52 Rmt.

6 Supplying and erecting B class Galvanized iron pipe having smooth

finished bore of the pipe on both ends erected nuts and bolts along

the pole / wall shaping the pipe as per site requirement. Pipe dia as

7 Providing and erecting Pipe type earthing having 150 cms.long and

cms. dia. galvanised iron pipe with coupling and buch buried in

specially prepared earth pit complete with necessary 8 SWG earth

wire. 27.00 368.65 Nos.

8 For using salt and charcoal / coke as required for pipe type earthing.

9 Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the

value of earthing resistane mentioned in test Certificate) & having

back filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted by

(a) For Electrical Installation up to 440V in normal soil Length of pipe -

Back filling compound - 1 Nos Bag of 15 Kg. 2.00 4591.46 Nos.

10 Making trench in Hard Murrum / Tar Road of suitable width of 90 cms

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. 713.43 74.74 Rmt.

11 Making trench in Hard Murrum / Tar Road of suitable width of 90 cm

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. (B) If additional machinery like hammer driller or JCB

use [Add] 126.57 357.54 Rmt.

12 Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth for laying

of cable. below ground / road surface for enclosing cable and back

filling the same to make ground as per original.

13 Providing and fixing Terminal board of size 5.0 x 127 x

mm.bakelite sheet with suitable brass studs with nuts, washers and

clamps of size 25mm x 3mm suitable for pole painted with one coat of

red lead paint. 27.00 146.45 Nos.

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom

including excavation for the pole of size 60 x 60 x 120 cm. Deep in

below ground level with plinth of 45 cm x 45 cm(or 45 cm dia x 45 cm)

high upper ground level with necessary curing and finishing in

approved manner. ( for 7.5 & 8/8.5 mtr pole) 27.00 1292.80 Nos.

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm 108.00 38.38 Nos.

(D) 2 to 4 core 16 Sq. mm 54.00 47.47 Nos.

16 Solderless crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

Supplying & erecting IP 55 grade following size section pillar fabricated

from joint less M.S. Sheet with angle iron legs made from jointless

M.S. Angle with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected with cement

concrete foundation and 45 cm high bricks work finishing with plaster

etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and

other with nut and bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank powder coated paint.

section pillar roof should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of 1962 2.00 1884.66 Nos.

(C) 60 X 30 X 45 cm section pillar fabricated from 16 Gauge MS Sheet

with angle iron legs 45 cm long made from 35 X 35 X 5 mm thick MS

18 Supplying and erecting HYLAM sheet on existing angle iron frame.for

following thickness (F) 12mm 1.00 2311.89 Smt.

Supplying & erecting approved make Digital time switch having lithium

cell 6 years operative and operate battery backup 1 channel day clock

with 14 memory programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time 1 minimum &

LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure

& transparent cover erected as required with necessary connection

erected as directed. 2.00 3168.37 Nos.

20 Supplying and erecting Ammeter / Voltmeter selector switch for

phase AC Supply 500 V on existing panel board with necessary

connections. 2.00 317.14 Nos.

Supplying and erecting approved make panel mounting type Digital

Ammeter having 3 digits LED display, external CT operated, calibrated

for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

22 Supplying and erecting approved make panel mounting type Digital

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected

on existing panel board with all connection, wiring etc .with

manufacturers calibration certificate. 2.00 1275.63 Nos.

Supplying and erecting approved make suitable panel indicator LED

type lamp, lens cover, complete erected with necessary connections.

24 Providing & erecting L.T. Current Transformer with bar primary 50/5

to 1000/5 ratio 15 VA burden erected in existing CRCA box duly

secured with insulating materials connected to the meter 2.00 274.72 Nos.

25 Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected in existing

16 G.M.S. housing.

ICS=100% of ICU only Cat III 2.00 6173.12 Nos.

26 providing and erecting Miniature circuit breaker single pole 0.5A to 2A

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat.III 27.00 270.68 Nos.

27 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity

(A) 6 to 32 Amp. Cat.III 2.00 578.73 Nos.

2 Providing, Supplying & Erecting Street Light Pole with LED Lights From Batla Lake Towards Jain Derasar at Borsad .

No Description Quantity Total Rate Per Amount

1 Providing decorative Single arm street light with 7.5mtr Steel tubular

pole (Swaged) confirming to IS - 2713 (Part-II) 1980 and bracket with

1500mm width and 750mm total height with suitable insertion pipe

diameter as per attached drawing with vertical plane & suitable

welded stays, reducer and with check nuts complete painted with one

coat of Red oxide / PU base primer and two coats of Aluminium / PU

paint. paint with following nos of arms. including M.S. Base plate 300 X

300 X 16 mm for pole, Suitable for mounting on surface of foundation

with GI foundation bolts,with pole required stiffeners welded also

Including LED IP-65 Light CCT-5000k Driver Efficiency - 85% Fitting As

Per Approved Bracket Design by Nagar Palika.

Supplying & erecting approved make SMC press moulded composite

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.

(B) 250mm x 200mm x 100mm [deep] 27.00 515.10 Nos.

4 Supplying and erecting Flexible PVC insulated multistrand multicore

1.1 kv grade ISI marked copper wires of following size to be erected as

e) 1.50 Sq.mm 3 core round PVC sheathed 594.00 31.31 Rmt.

5 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

(A) 4 core 16 Sq. mm 1216.00 153.52 Rmt.

6 Supplying and erecting B class Galvanized iron pipe having smooth

finished bore of the pipe on both ends erected nuts and bolts along

the pole / wall shaping the pipe as per site requirement. Pipe dia as

7 Providing and erecting Pipe type earthing having 150 cms.long and

cms. dia. galvanised iron pipe with coupling and buch buried in

specially prepared earth pit complete with necessary 8 SWG earth

wire. 27.00 368.65 Nos.

8 For using salt and charcoal / coke as required for pipe type earthing.

9 Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the

value of earthing resistane mentioned in test Certificate) & having

back filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted by

(a) For Electrical Installation up to 440V in normal soil Length of pipe -

Back filling compound - 1 Nos Bag of 15 Kg. 2.00 4591.46 Nos.

10 Making trench in Hard Murrum / Tar Road of suitable width of 90 cms

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. 877.58 74.74 Rmt.

11 Making trench in Hard Murrum / Tar Road of suitable width of 90 cm

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. (B) If additional machinery like hammer driller or JCB

use [Add] 222.43 357.54 Rmt.

12 Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth for laying

of cable. below ground / road surface for enclosing cable and back

filling the same to make ground as per original.

13 Providing and fixing Terminal board of size 5.0 x 127 x

mm.bakelite sheet with suitable brass studs with nuts, washers and

clamps of size 25mm x 3mm suitable for pole painted with one coat of

red lead paint. 27.00 146.45 Nos.

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom

including excavation for the pole of size 60 x 60 x 120 cm. Deep in

below ground level with plinth of 45 cm x 45 cm(or 45 cm dia x 45 cm)

high upper ground level with necessary curing and finishing in

approved manner. ( for 7.5 & 8/8.5 mtr pole) 27.00 1292.80 Nos.

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm 108.00 38.38 Nos.

(D) 2 to 4 core 16 Sq. mm 54.00 47.47 Nos.

16 Solderless crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

Supplying & erecting IP 55 grade following size section pillar fabricated

from joint less M.S. Sheet with angle iron legs made from jointless

M.S. Angle with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected with cement

concrete foundation and 45 cm high bricks work finishing with plaster

etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and

other with nut and bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank powder coated paint.

section pillar roof should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of 1962 2.00 1884.66 Nos.

(C) 60 X 30 X 45 cm section pillar fabricated from 16 Gauge MS Sheet

with angle iron legs 45 cm long made from 35 X 35 X 5 mm thick MS

18 Supplying and erecting HYLAM sheet on existing angle iron frame.for

following thickness (F) 12mm 1.00 2311.89 Smt.

Supplying & erecting approved make Digital time switch having lithium

cell 6 years operative and operate battery backup 1 channel day clock

with 14 memory programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time 1 minimum &

LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure

& transparent cover erected as required with necessary connection

erected as directed. 2.00 3168.37 Nos.

20 Supplying and erecting Ammeter / Voltmeter selector switch for

phase AC Supply 500 V on existing panel board with necessary

connections. 2.00 317.14 Nos.

Supplying and erecting approved make panel mounting type Digital

Ammeter having 3 digits LED display, external CT operated, calibrated

for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

22 Supplying and erecting approved make panel mounting type Digital

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected

on existing panel board with all connection, wiring etc .with

manufacturers calibration certificate. 2.00 1275.63 Nos.

Supplying and erecting approved make suitable panel indicator LED

type lamp, lens cover, complete erected with necessary connections.

24 Providing & erecting L.T. Current Transformer with bar primary 50/5

to 1000/5 ratio 15 VA burden erected in existing CRCA box duly

secured with insulating materials connected to the meter 2.00 274.72 Nos.

25 Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected in existing

16 G.M.S. housing.

ICS=100% of ICU only Cat III 2.00 6173.12 Nos.

26 providing and erecting Miniature circuit breaker single pole 0.5A to 2A

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat.III 27.00 270.68 Nos.

27 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity

(A) 6 to 32 Amp. Cat.III 2.00 578.73 Nos.

3 Providing, Supplying & Erecting Remaning Street Light Pole with LED Lights From Anand Cross road to Bridge At Borsad

No Description Quantity Total Rate Per Amount

1 LED DECORATIVE POLE MODEL - 1764 - CLASSIQUE 7.5 MTR with

DOUBLE ARM BRACKET DECORATIVE POLE WITH PU PAINTPIPE SIZE -

150X150X3.5MM AND 58OD, 3MM BASE PLATE SIZE - 300X300X16MM

MATERIAL TYPE - M.S POWDER COATED also Including LED IP-65 Light

CCT-5000k Driver Efficiency - 85% Fitting As Per Approved Bracket

Design by Nagar Palika.

2 LED DECORATIVE POLE MODEL - 1764 - CLASSIQUE 7.5 MTR with

TRIPLE ARM BRACKET DECORATIVE POLE WITH PU PAINTPIPE SIZE -

150X150X3.5MM AND 58OD, 3MM BASE PLATE SIZE - 300X300X16MM

MATERIAL TYPE - M.S POWDER COATED also Including LED IP-65 Light

CCT-5000k Driver Efficiency - 85% Fitting As Per Approved Bracket

Design by Nagar Palika.

Supplying & erecting approved make SMC press moulded composite

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.

(a) 300mm x 200mm x 100mm [deep] 20.00 898.90 Nos.

5 Supplying and erecting Flexible PVC insulated multistrand multicore

1.1 kv grade ISI marked copper wires of following size to be erected as

e) 1.50 Sq.mm 3 core round PVC sheathed 1012.00 31.31 Rmt.

6 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

(A) 4 core 16 Sq. mm 776.00 153.52 Rmt.

7 Supplying and erecting B class Galvanized iron pipe having smooth

finished bore of the pipe on both ends erected nuts and bolts along

the pole / wall shaping the pipe as per site requirement. Pipe dia as

8 Providing and erecting Pipe type earthing having 150 cms.long and

cms. dia. galvanised iron pipe with coupling and buch buried in

specially prepared earth pit complete with necessary 8 SWG earth

wire. 20.00 368.65 Nos.

9 For using salt and charcoal / coke as required for pipe type earthing.

10 Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test

certificate including value of earth resistane of installation

[C] For Electrical Installation covering Transformer Neutrals, Lightning

arrester Earthing, A.C.Plant & Sensitive Computer System(like

Automation, SCADA)i.e. independent Earthing located in other

than normal soil i.e. Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg.

11 Making trench in Hard Murrum / Tar Road of suitable width of 90 cms

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. 500.00 74.74 Rmt.

12 Making trench in Hard Murrum / Tar Road of suitable width of 90 cm

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. (B) If additional machinery like hammer driller or JCB

use [Add] 0.00 357.54 Rmt.

13 Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth for laying

of cable. below ground / road surface for enclosing cable and back

filling the same to make ground as per original.

14 Providing and fixing Terminal board of size 5.0 x 127 x

mm.bakelite sheet with suitable brass studs with nuts, washers and

clamps of size 25mm x 3mm suitable for pole painted with one coat of

red lead paint. 20.00 146.45 Nos.

15 Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom

including excavation for the pole of size 60 x 60 x 150 cm. Deep in

below ground level with plinth of 45 cm x 45 cm(or 45 cm dia x 45 cm)

high upper ground level with necessary curing and finishing in

approved manner. 20.00 1652.36 Nos.

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm 80.00 38.38 Nos.

(D) 2 to 4 core 16 Sq. mm 40.00 47.47 Nos.

17 Solderless crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

Supplying & erecting IP 55 grade following size section pillar fabricated

from joint less M.S. Sheet with angle iron legs made from jointless

M.S. Angle with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected with cement

concrete foundation and 45 cm high bricks work finishing with plaster

etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and

other with nut and bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank powder coated paint.

section pillar roof should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of 1962 1.00 16691.26 Nos.

(A) 150 X 90 X 75 cm section pillar fabricated from 14 Gauge MS Sheet

with angle iron legs 95 cm long made from 40 X 40 X 6 mm thick MS

19 Supplying and erecting HYLAM sheet on existing angle iron frame.for

following thickness (F) 12mm 1.00 2311.89 Smt.

Supplying & erecting approved make Digital time switch having lithium

cell 6 years operative and operate battery backup 1 channel day clock

with 14 memory programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time 1 minimum &

LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure

& transparent cover erected as required with necessary connection

erected as directed. 1.00 3168.37 Nos.

21 Supplying and erecting Ammeter / Voltmeter selector switch for

phase AC Supply 500 V on existing panel board with necessary

connections. 1.00 317.14 Nos.

Supplying and erecting approved make panel mounting type Digital

Ammeter having 3 digits LED display, external CT operated, calibrated

for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

23 Supplying and erecting approved make panel mounting type Digital

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected

on existing panel board with all connection, wiring etc .with

manufacturers calibration certificate. 1.00 1275.63 Nos.

Supplying and erecting approved make suitable panel indicator LED

type lamp, lens cover, complete erected with necessary connections.

25 Providing & erecting L.T. Current Transformer with bar primary 50/5

to 1000/5 ratio 15 VA burden erected in existing CRCA box duly

secured with insulating materials connected to the meter 1.00 274.72 Nos.

26 Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected in existing

16 G.M.S. housing.

ICS=100% of ICU only Cat III 1.00 6173.12 Nos.

27 providing and erecting Miniature circuit breaker single pole 0.5A to 2A

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat.III 14.00 270.68 Nos.

28 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity

(A) 6 to 32 Amp. Cat.III 1.00 578.73 Nos.

4 Providing, Supplying & Erecting Street Light Pole with LED Lights At Tornavmata lake Road at Borsad .

No Description Quantity Total Rate Per Amount

1 LED DECORATIVE POLE MODEL - 1741 - WAVE 3.6 MTR DECORATIVE

POLE WITH PU PAINTPIPE SIZE - 150X150X3.5MM AND 58OD, 3MM

BASE PLATE SIZE - 300X300X16MM MATERIAL TYPE - M.S /

ALUMINIUM POWDER COATED also Including LED IP-65 Light CCT-

5000k Driver Efficiency - 85% Fitting As Per Approved Bracket Design

by Nagar Palika. 50.00 21995.78 NO.

Supplying & erecting approved make SMC press moulded composite

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.

(B) 250mm x 200mm x 100mm [deep] 50.00 515.10 Nos.

4 Supplying and erecting Flexible PVC insulated multistrand multicore

1.1 kv grade ISI marked copper wires of following size to be erected as

e) 1.50 Sq.mm 3 core round PVC sheathed 1100.00 31.31 Rmt.

5 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

(A) 4 core 16 Sq. mm 1400.00 153.52 Rmt.

6 Supplying and erecting B class Galvanized iron pipe having smooth

finished bore of the pipe on both ends erected nuts and bolts along

the pole / wall shaping the pipe as per site requirement. Pipe dia as

7 Providing and erecting Pipe type earthing having 150 cms.long and

cms. dia. galvanised iron pipe with coupling and buch buried in

specially prepared earth pit complete with necessary 8 SWG earth

wire. 50.00 368.65 Nos.

8 For using salt and charcoal / coke as required for pipe type earthing.

9 Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the

value of earthing resistane mentioned in test Certificate) & having

back filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted by

(a) For Electrical Installation up to 440V in normal soil Length of pipe -

Back filling compound - 1 Nos Bag of 15 Kg. 1.00 4591.46 Nos.

10 Making trench in Hard Murrum / Tar Road of suitable width of 90 cms

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. 350.00 74.74 Rmt.

11 Making trench in Hard Murrum / Tar Road of suitable width of 90 cm

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

normal ground. (B) If additional machinery like hammer driller or JCB

use [Add] 150.00 357.54 Rmt.

12 Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth for laying

of cable. below ground / road surface for enclosing cable and back

filling the same to make ground as per original.

13 Providing and fixing Terminal board of size 5.0 x 127 x

mm.bakelite sheet with suitable brass studs with nuts, washers and

clamps of size 25mm x 3mm suitable for pole painted with one coat of

red lead paint. 50.00 146.45 Nos.

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom

including excavation for the pole of size 60 x 60 x 120 cm. Deep in

below ground level with plinth of 45 cm x 45 cm(or 45 cm dia x 45 cm)

high upper ground level with necessary curing and finishing in

approved manner. ( for 7.5 & 8/8.5 mtr pole) 50.00 1292.80 Nos.

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm 300.00 38.38 Nos.

(D) 2 to 4 core 16 Sq. mm 200.00 47.47 Nos.

16 Solderless crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

Supplying & erecting IP 55 grade following size section pillar fabricated

from joint less M.S. Sheet with angle iron legs made from jointless

M.S. Angle with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected with cement

concrete foundation and 45 cm high bricks work finishing with plaster

etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and

other with nut and bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank powder coated paint.

section pillar roof should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of 1962 2.00 1884.66 Nos.

(C) 60 X 30 X 45 cm section pillar fabricated from 16 Gauge MS Sheet

with angle iron legs 45 cm long made from 35 X 35 X 5 mm thick MS

18 Supplying and erecting HYLAM sheet on existing angle iron frame.for

following thickness (F) 12mm 1.00 2311.89 Smt.

Supplying & erecting approved make Digital time switch having lithium

cell 6 years operative and operate battery backup 1 channel day clock

with 14 memory programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time 1 minimum &

LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure

& transparent cover erected as required with necessary connection

erected as directed. 1.00 3168.37 Nos.

20 Supplying and erecting Ammeter / Voltmeter selector switch for

phase AC Supply 500 V on existing panel board with necessary

connections. 1.00 317.14 Nos.

Supplying and erecting approved make panel mounting type Digital

Ammeter having 3 digits LED display, external CT operated, calibrated

for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

22 Supplying and erecting approved make panel mounting type Digital

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected

on existing panel board with all connection, wiring etc .with

manufacturers calibration certificate. 1.00 1275.63 Nos.

Supplying and erecting approved make suitable panel indicator LED

type lamp, lens cover, complete erected with necessary connections.

24 Providing & erecting L.T. Current Transformer with bar primary 50/5

to 1000/5 ratio 15 VA burden erected in existing CRCA box duly

secured with insulating materials connected to the meter 1.00 274.72 Nos.

25 Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected in existing

16 G.M.S. housing.

ICS=100% of ICU only Cat III 1.00 6173.12 Nos.

26 providing and erecting Miniature circuit breaker single pole 0.5A to 2A

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat.III 50.00 270.68 Nos.

27 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity

(A) 6 to 32 Amp. Cat.III 1.00 578.73 Nos.

A+B+C+D Total :

Add 3 % Cont. & Superv. :

BORSAD NAGAR PALIKA

1 PROVIDING OF FIRE FIGHTING SYSTEM AT CITY POINT , BORSAD

2 INSTALLATION OF FIRE FIGHTING SYSTEM AT SILVER POINT, BORSAD

3 INSTALLATION OF FIRE FIGHTING SYSTEM AT F.P. NO. 138, BORSAD

1 PROVIDING OF FIRE FIGHTING SYSTEM AT CITY POINT , BORSAD

No Description QTY. Per Amount

1 Providing ans supplying ISI mark GI Pipes with

coupling of following class and diameter including all

taxes insurances transportation freight charges

octroi inspection charges, loadinghg , unloading,

conveyance to departmental stores stacking etc

complete. 100 mm dia

2 Lowering laying and jointing GI pipes with GI specials

of following diameter in proper position grade and

allignment as directed by Engineer in charge

including conveyance from stores to site of work

labour given hydraulic testing etc complete. 100 mm

dia 190 34.34 RMT

3 Providing ans supplying ISI mark GI Pipes with

coupling of following class and diameter including all

taxes insurances transportation freight charges

octroi inspection charges, loadinghg , unloading,

conveyance to departmental stores stacking etc

complete. 80 mm dia

4 Lowering laying and jointing GI pipes with GI specials

of following diameter in proper position grade and

allignment as directed by Engineer in charge

including conveyance from stores to site of work

labour given hydraulic testing etc complete. 80 mm

dia 48 27.27 RMT

5 Providing and fixing 63 mm dia 15 mtr. long

rubberized fabric lined hose including SS male and

female instantaneous type coupling machine bound

with binding complete in all respects hose to IS:636

type-I and S.S. coupling to IS: 903 with ISI

certification. 12 8,585.00 Nos

6 Providing and fixing of 63 mm dia instantaneous

pattern SS short branch pipe, 20 mm dia nozzle

conforming to IS 903 with ISI mark, suitable for inter

connection to hose pipe coupling complete.

7 Providing, fixing and commissioning of Fire Hose BOX

Single door, fabricated from 22 gauge M.S sheet

(with glass) with locking and break glass recess for

key.: Installation, Testing & Commissioning of box of

size 450 mm x 600 mm x 250 mm (external use) with

stand of thickness 3 mm with 6 mm thick glazed

glass doors for housing the below mentioned items

with lockable glass doors, at desired location etc.

complete to accommodate landing Valve,1 No of

Long Hose Pipe, 1 Nos of Branch pipe mounted &

duly painted with Post officered externally and white

internally with synthetic enamel paint complete in

all respect, SS SINGLE HEADED HYDRANT VALVE: SITC

of fire hydrants as per IS 5290, consisting of 63 mm

dia, Single outlet flanged oblique type hydrant valve

with instantaneous female plunger type coupling,

chained blank cap in including making flanged joints

by providing necessary nuts, bolts, gaskets (4 mm

thick neoprene) all complete as suitable for 80 mm

dia stand post etc. all as per specification complete

8 SS SINGLE HEADED HYDRANT VALVE: SITC of fire

hydrants as per IS 5290, consisting of 63 mm dia,

Single outlet flanged oblique type hydrant valve with

instantaneous female plunger type coupling, chained

blank cap in including making flanged joints by

providing necessary nuts, bolts, gaskets (4 mm thick

neoprene) all complete as suitable for 80 mm dia

stand post etc. all as per specification complete as

9 HOSE REEL DRUM: SITC of Hose reel wall mounting

type drum completed with wall mounting bracket

complete with 20 mm x 30 mtr long, fitted with

mm SS 304 shut off nozzle with ball valve of 20 mm

confirming to IS :884 making connection to the

vertical riser by cutting welding, including providing

20mm dia shut off valve, all necessary piping,

fittings, fixing the hose reel with necessary anchor

fasteners by drilling holes in walls /RCC and in case

of yard line connection it must be comply with

support stand (MS Fabricated stand) making good

the same etc. all as per specification complete as

10 :Supply of Fire Brigade inlet with 4 nos 63mm dia

G.M. male hydrant connection including providing

and fixing 150mm dia Butterfly Valve PN 16 etc. for

the hydrant loop etc. all as per specification

complete as directed. 1 3,042.12 Nos

11 ABC TYPE POWDER FIRE EXTINGUISHER 6 KG

:Installation of portable fire extinguishers of 6 kg

capacity (dry powder - Class ABC ) suitable for wall

mounting including fixing the same with necessary

brackets / clamps / anchor bolts drilling holes

making good the same painting the surface as

required with ISI : 15683 etc. all as per specification

complete as directed. 12 2,878.50 Nos

CO2 TYPE FIRE EXTINGUISHER 4.5 KG :Installation &

Testing of portable fire extinguishers (CO2) of 4.5 kg

capacity confirming to IS : 2878 and certificate from

explosive dept. suitable for wall mounting including

fixing the same with necessary brackets / clamps /

anchor bolts drilling holes making good the same

painting the surface as required with ISI etc. all as

per specification complete as directed per

specification complete as directed

Cost of Horizontal type, multistage, centrifudgal,

solit cating pump with brinze impeller stainless steel

shaft, mechanical seal at a flow of 1620 lpm at 56 m

Head conforming to IS

Cost of 40 HP SQ Cage induction motor, TEFC,

Synchronous speed of 1500 RPM having class - 'F'

insulation and protection class IP 55 as per IS -

Cost of MS base plate coupling, coupling guard,

foundation bolts and anti vibration pads

14 Supply, installation, testing & commissioning of

V Fully automatic Microprocessor based soft starter

with external bypass arragement for pump control

application as per general specification as under

control method - torque control , input voltage -415

v, 3 phase , input frquency -50/60 Hz (+- 5%),

confirmative to standard - IEC 61947-4-2UL. CSA, CE,

Motor protection- inbuilt thermal protection, starter

protection- SC UV, Phase unbalance, Phase failure,

EMC Std-IEC 61000-4-2 Level 3 & IEC 61000-4-3

LEVEL-3. bUILT IN COMMUNICATION AS PER rs

ELECTRICALS FOR FIRE HYDRANT SYSTEM Supply of

Power cabling and control cabling from Fire pump

controller to Fire Pumps etc. all as per specification

complete as directed. Item also includes supply of

Main Incomer Cable from Main Electrical Panel to

Main Fire Panel in Pump House double earthing for

pumps instruments, panels etc. (cable 4 core x

Providing, fixing, testing & commissioning of 100 mm

dia Burden type, Stainless Steel dial type pressure

gauge (in Pump Room) including brass isolation valve

and pipe having calibration of 0-16 Kg/cm2. : Supply

of pressure gauges of suitable range for pump sets

with ball valves, siphon, and fittings like unions/

collars/ reducers etc. NOTE: Pressure range 0-20 bar

etc. all as per specification complete as directed.

Providing and fixing C.I. Butterfly valve, water type

class PN 1.6 as per IS: 13095 , including necessary

nuts, bolts, gaskets etc. with flanges as required,

complete in all respects. For 100 mm nominal bore.

:Supply of 100 mm dia. lever operated slim seal type

CI butterfly valves with ss disc conforming to IS-

13095 of PN 1.6 rating along with its all accessories

such as flanges, nut-bolt-washers, gaskets etc. at

shown location including making suitable fixing

arrangement & carrying out all related works etc. all

as per specification complete as directed.

Providing and fixing pressure switch KP- 36 (for

operation at 0-15 Kg. /sqcm) with required fittings

and accessories complete. : Supply of pressure

switch for auto-operation of all pumps in sequences

(with cable approx. 4X10 MTR) etc. all as per

specification complete as directed.

Supply and installation of 100 mm nominal bore.

Foot Valve (Heavy Duty, Non-Return Type) with built-

in strainer, suitable for pump suction line. Ensures

prevention of backflow, maintains pump priming,

and protects the pump from debris and damage

20 M S STRUCTURAL STEEL FOR SUPPORTS M S

STRUCTURAL STEEL FOR SUPPORTS: Supply of MS

steel for supports of fire hydrant network going

along with the MS structure of plant or from the wall

for support etc. all as per specification complete as

directed. 400 232.30 Kg

Providing and supplying ISI mark CI D/F Reflux Valves

as per IS:5312 [Latest Edition) of following class and

diameter including all taxes, Insurance,

transportation, freight charges, octroi, inspection

charges, loading, unloading. conveyance to

departmental stores, stacking etc. complete 100 mm

Dia Reflux valves PN 1.0 IS 5312 with ISI mark

Lowering, laying and jointing in position following C.

I. / D/F Reflux valves, Butterfly valves, Sluice valves

and Air valves including cost of all labour, jointing

material, including nut bolts and giving satisfactory

hydraulic testing, etc. complete. Sluice valves,

Butterfly Valves, Reflux Valves

23 Supply, installation, testing and commissioning of Air

Release valve of size as mentioned in the item. :

Supply of Suitable G.M... Air release valve of 25mm

dia PN 16 all as per specification complete as

directed. 2 724.17 Nos

24 Supply and Installation of 2 zone conventional fire

alarm panel with Battery back up 2 No 1 27,270.00 Nos

25 MANUAL CALL POINT MANUAL CALL POINT Supply,

Installation, testing and commissioning of

conventional type manual call point 12 808.00 Nos

26 HOOTERS Supply, Installation, testing and

commissioning of conventional type hooters 12 808.00 Nos

27 FIRE ALARM CABLE Providing, fixing, testing and

commissioning of Red Colour 2 Core X 1.5 Sqmm

Flexible copper FRLS Cable .Item includes providing

and fixing cable accessories complete as per

specifications and as per NBC/IS/Engineer In charge

requirements 610 145.44 Rmt

CABLE Providing and fixing PVC insulated copper

conductor armored cable SIZE 3C x 2.5 sq mm

complete with necessary saddling and clamping

including providing and fixing GI Cable clamps, cable

glands and lugs at both ends as per specification

29 PHOTOLUMINICENT SIGNAGES Proving, Fixing and

Commissioning of VARIOUS Signage’s

30 RCC Under Ground Sump

Preparing structural design of RCC Under Ground /

Partially under ground / above high ground level

Reservoir of required capacity as per relevant I.S.

standards and constructing the same, including

excavation in all types of soil strata (including rock)

including shoring strutting if required, for loose soil /

to protect from collapse, casting 100 mm thick P.C.C.

levelling course in M15, Refilling the pit with proper

soil and disposing of the surplus stuff at all lead.

Including cement plaster in CM 1:2 with approved

water proofing compound to all over inside

container (i.e. walls, base, top slab/dome bottom

etc. all). Including all types of labour and material

charges of lowering, laying, erecting / hosting and

jointing of pipe assembly to inlet, outlet overflow,

washout and bye pass arrangement as per hydraulic

Providing and fixing accessories, CI Manhole frame

and cover, water level indicator, adequate cowl type

ventilators or lantern type ventilator with stainless

steel jail. RCC chambers for valves. Providing and

applying three coats of cement paint / snowcem to

the out side face of structure. It also includes

satisfactory water tightness test as per relevant I.S.

code and painting name of scheme and capacity on

the tank as per direction of engineer in charge.

List of Indian Standards for Design of GSR / SUMP:-

The structural design of GSR shall be in accordance

with provisions relevant I.S standards

(1) I.S. 3370 part I & II 2009 or Its latest revision

(1.1) I.S. 3370 part III & IV 1965 or Its latest revision

(2) I.S. 456 – 2000 or Its latest revision

(3) I.S. 1893 – 2000 – 1984 or Its latest revision.

(4) I.S. 875, Part – 1 to 3, 1987 or Its latest revision.

General Specifications:-

(1) Water depth in container shall be adopted as per

data of tender. Capacity shall be calculated excluding

free board of the reservoir. If water depth is not

specified, the suitable water depth / acceptable to

field engineer in accordance with hydraulic

requirement shall be adopted for capacity

(2) Shape of container (in plan) specified by in data

shall be adopted in absence circular shape shall be

(3) Size shall be fixed as per availability of space

(land area) at site / acceptable engineer in charge

(4) Effect of overlapping of pressure bulbs on soil

due near by structure and proposed sump should be

(5) Care shall be taken that no damage should occur

to nearby existing structure. Compensation shall be

paid for the same by agency.

(6) The minimum concrete grade for RCC shall be M-

(7) HYSD Fe 415 / 500 grade reinforcing bars

confirming to I.S. 1786 / 1139 shall be considered in

design. CRS / TMT bars shall be provided. In saline

atmosphere corrosion resistance stainless steel /

HCR rebar shall be provided. Any other steel can be

used with approval of C.E./ in situation of non

availability in market without extra cost.

(8) Minimum size (or thickness) of various

components shall be provided as per tender criteria

/ specifications in absence as per I.S./ Std. practice of

G.W.S.S.B. Minimum dimensions specified for

various components in tender data / specifications

shall be provided without fail.

(9) The safe bearing capacity (SBC) shall be referred

from SBC test report. In absence of report it shall be

referred from data sheet. If poor soil is found /

water table is met with during excavation SBC shall

be scientifically ascertained and design shall be

revise. No extra shall be paid for increase in

(10) DI pipes and special shall only be used if type is

not specified in tender

(11) The rate shall include cost of dewatering during

excavation making all arrangement when water

table meets within depth.

(12) The structure shall be designed properly to

resist uplift due to ground water table specified in

data or actual ground water table meets with during

excavation. If GWT / Uplift is mentioned in tender

and during excavation it dose not meet 7.5% rate

shall be reduced.

(13) SS pipes railing shall be provided over sump

perifery when sump height is ≥ 1.5 meter above

(14.a) RCC staircase/RCC Steps should be provided

from GL to sump top slab based on the height of the

GSR above/below the ground.

(14.b) RCC Staircase with SS railing to be provided

inside reservoir container. BB Masonry staircabin to

be provided to cover the same with MS safety door

having locking arrangement.

(15) Appearance of structure should be aesthetically

good looking acceptable to authority.

(16) Any change in size, shape, depth below GL,

height above GL, water depth, F.B., size of member

etc can be permitted in exceptional case due to site

condition or hydraulic design requirement by C.E. No

extra shall be paid for change.

(17) Any change in data, dimensions, shape, water

depth, reduction in size if permitted by competent

authority and if it reduces quantity then payment

shall be reduced prorate.

(18) When capacity of GSR / Sump is > 20 lakh litres

two or suitable compartments acceptable to

executive engineer shall be designed and provided.

(19) Agency shall engage qualified (at least graduate)

consulting engineer for designing the structure and

he / she shall visit the site for guidance of work.

(20) 75% part rate shall be payable for concrete,

reinforcement and plastering items of container

until satisfactory hydraulic testing for water

tightness is performed as per tender condition. Till

the work shall be treated as incomplete.

Above conditions / general specifications Sr. No. 1 to

20 are part and parcel of tender (contact) and

prevail over other provisions

As above without water table (Sub soil water level

below foundation)

Cost for 50000 litres capacity 1 Nos.

2 INSTALLATION OF FIRE FIGHTING SYSTEM AT SILVER POINT, BORSAD

No Description QTY. Per Amount

1 Providing ans supplying ISI mark GI Pipes with

coupling of following class and diameter including all

taxes insurances transportation freight charges

octroi inspection charges, loadinghg , unloading,

conveyance to departmental stores stacking etc

complete. 100 mm dia

2 Lowering laying and jointing GI pipes with GI specials

of following diameter in proper position grade and

allignment as directed by Engineer in charge

including conveyance from stores to site of work

labour given hydraulic testing etc complete. 100 mm

dia 220 34.34 RMT

3 Providing ans supplying ISI mark GI Pipes with

coupling of following class and diameter including all

taxes insurances transportation freight charges

octroi inspection charges, loadinghg , unloading,

conveyance to departmental stores stacking etc

complete. 80 mm dia

4 Lowering laying and jointing GI pipes with GI specials

of following diameter in proper position grade and

allignment as directed by Engineer in charge

including conveyance from stores to site of work

labour given hydraulic testing etc complete. 80 mm

dia 48 27.27 RMT

5 Providing and fixing 63 mm dia 15 mtr. long

rubberized fabric lined hose including SS male and

female instantaneous type coupling machine bound

with binding complete in all respects hose to IS:636

type-I and S.S. coupling to IS: 903 with ISI

certification. 12 8,585.00 Nos

6 Providing and fixing of 63 mm dia instantaneous

pattern SS short branch pipe, 20 mm dia nozzle

conforming to IS 903 with ISI mark, suitable for inter

connection to hose pipe coupling complete.

7 Providing, fixing and commissioning of Fire Hose BOX

Single door, fabricated from 22 gauge M.S sheet

(with glass) with locking and break glass recess for

key.: Installation, Testing & Commissioning of box of

size 450 mm x 600 mm x 250 mm (external use) with

stand of thickness 3 mm with 6 mm thick glazed

glass doors for housing the below mentioned items

with lockable glass doors, at desired location etc.

complete to accommodate landing Valve,1 No of

Long Hose Pipe, 1 Nos of Branch pipe mounted &

duly painted with Post officered externally and white

internally with synthetic enamel paint complete in

all respect, SS SINGLE HEADED HYDRANT VALVE: SITC

of fire hydrants as per IS 5290, consisting of 63 mm

dia, Single outlet flanged oblique type hydrant valve

with instantaneous female plunger type coupling,

chained blank cap in including making flanged joints

by providing necessary nuts, bolts, gaskets (4 mm

thick neoprene) all complete as suitable for 80 mm

dia stand post etc. all as per specification complete

8 SS SINGLE HEADED HYDRANT VALVE: SITC of fire

hydrants as per IS 5290, consisting of 63 mm dia,

Single outlet flanged oblique type hydrant valve with

instantaneous female plunger type coupling, chained

blank cap in including making flanged joints by

providing necessary nuts, bolts, gaskets (4 mm thick

neoprene) all complete as suitable for 80 mm dia

stand post etc. all as per specification complete as

9 HOSE REEL DRUM: SITC of Hose reel wall mounting

type drum completed with wall mounting bracket

complete with 20 mm x 30 mtr long, fitted with

mm SS 304 shut off nozzle with ball valve of 20 mm

confirming to IS :884 making connection to the

vertical riser by cutting welding, including providing

20mm dia shut off valve, all necessary piping,

fittings, fixing the hose reel with necessary anchor

fasteners by drilling holes in walls /RCC and in case

of yard line connection it must be comply with

support stand (MS Fabricated stand) making good

the same etc. all as per specification complete as

10 :Supply of Fire Brigade inlet with 4 nos 63mm dia

G.M. male hydrant connection including providing

and fixing 150mm dia Butterfly Valve PN 16 etc. for

the hydrant loop etc. all as per specification

complete as directed. 1 3,042.12 Nos

11 ABC TYPE POWDER FIRE EXTINGUISHER 6 KG

:Installation of portable fire extinguishers of 6 kg

capacity (dry powder - Class ABC ) suitable for wall

mounting including fixing the same with necessary

brackets / clamps / anchor bolts drilling holes

making good the same painting the surface as

required with ISI : 15683 etc. all as per specification

complete as directed. 9 2,878.50 Nos

CO2 TYPE FIRE EXTINGUISHER 4.5 KG :Installation &

Testing of portable fire extinguishers (CO2) of 4.5 kg

capacity confirming to IS : 2878 and certificate from

explosive dept. suitable for wall mounting including

fixing the same with necessary brackets / clamps /

anchor bolts drilling holes making good the same

painting the surface as required with ISI etc. all as

per specification complete as directed per

specification complete as directed

Cost of Horizontal type, multistage, centrifudgal,

solit cating pump with brinze impeller stainless steel

shaft, mechanical seal at a flow of 1620 lpm at 56 m

Head conforming to IS

Cost of 40 HP SQ Cage induction motor, TEFC,

Synchronous speed of 1500 RPM having class - 'F'

insulation and protection class IP 55 as per IS -

Cost of MS base plate coupling, coupling guard,

foundation bolts and anti vibration pads

14 Supply, installation, testing & commissioning of

V Fully automatic Microprocessor based soft starter

with external bypass arragement for pump control

application as per general specification as under

control method - torque control , input voltage -415

v, 3 phase , input frquency -50/60 Hz (+- 5%),

confirmative to standard - IEC 61947-4-2UL. CSA, CE,

Motor protection- inbuilt thermal protection, starter

protection- SC UV, Phase unbalance, Phase failure,

EMC Std-IEC 61000-4-2 Level 3 & IEC 61000-4-3

LEVEL-3. bUILT IN COMMUNICATION AS PER rs

ELECTRICALS FOR FIRE HYDRANT SYSTEM Supply of

Power cabling and control cabling from Fire pump

controller to Fire Pumps etc. all as per specification

complete as directed. Item also includes supply of

Main Incomer Cable from Main Electrical Panel to

Main Fire Panel in Pump House double earthing for

pumps instruments, panels etc. (cable 4 core x

Providing, fixing, testing & commissioning of 100 mm

dia Burden type, Stainless Steel dial type pressure

gauge (in Pump Room) including brass isolation valve

and pipe having calibration of 0-16 Kg/cm2. : Supply

of pressure gauges of suitable range for pump sets

with ball valves, siphon, and fittings like unions/

collars/ reducers etc. NOTE: Pressure range 0-20 bar

etc. all as per specification complete as directed.

Providing and fixing C.I. Butterfly valve, water type

class PN 1.6 as per IS: 13095 , including necessary

nuts, bolts, gaskets etc. with flanges as required,

complete in all respects. For 100 mm nominal bore.

:Supply of 100 mm dia. lever operated slim seal type

CI butterfly valves with ss disc conforming to IS-

13095 of PN 1.6 rating along with its all accessories

such as flanges, nut-bolt-washers, gaskets etc. at

shown location including making suitable fixing

arrangement & carrying out all related works etc. all

as per specification complete as directed.

Providing and fixing pressure switch KP- 36 (for

operation at 0-15 Kg. /sqcm) with required fittings

and accessories complete. : Supply of pressure

switch for auto-operation of all pumps in sequences

(with cable approx. 4X10 MTR) etc. all as per

specification complete as directed.

Supply and installation of 100 mm nominal bore.

Foot Valve (Heavy Duty, Non-Return Type) with built-

in strainer, suitable for pump suction line. Ensures

prevention of backflow, maintains pump priming,

and protects the pump from debris and damage

20 M S STRUCTURAL STEEL FOR SUPPORTS M S

STRUCTURAL STEEL FOR SUPPORTS: Supply of MS

steel for supports of fire hydrant network going

along with the MS structure of plant or from the wall

for support etc. all as per specification complete as

directed. 450 232.30 Kg

Providing and supplying ISI mark CI D/F Reflux Valves

as per IS:5312 [Latest Edition) of following class and

diameter including all taxes, Insurance,

transportation, freight charges, octroi, inspection

charges, loading, unloading. conveyance to

departmental stores, stacking etc. complete 100 mm

Dia Reflux valves PN 1.0 IS 5312 with ISI mark

Lowering, laying and jointing in position following C.

I. / D/F Reflux valves, Butterfly valves, Sluice valves

and Air valves including cost of all labour, jointing

material, including nut bolts and giving satisfactory

hydraulic testing, etc. complete. Sluice valves,

Butterfly Valves, Reflux Valves

23 Supply, installation, testing and commissioning of Air

Release valve of size as mentioned in the item. :

Supply of Suitable G.M... Air release valve of 25mm

dia PN 16 all as per specification complete as

directed. 2 724.17 Nos

24 Supply and Installation of 2 zone conventional fire

alarm panel with Battery back up 2 No 1 27,270.00 Nos

25 MANUAL CALL POINT MANUAL CALL POINT Supply,

Installation, testing and commissioning of

conventional type manual call point 12 808.00 Nos

26 HOOTERS Supply, Installation, testing and

commissioning of conventional type hooters 12 808.00 Nos

27 FIRE ALARM CABLE Providing, fixing, testing and

commissioning of Red Colour 2 Core X 1.5 Sqmm

Flexible copper FRLS Cable .Item includes providing

and fixing cable accessories complete as per

specifications and as per NBC/IS/Engineer In charge

requirements 600 145.44 Rmt

CABLE Providing and fixing PVC insulated copper

conductor armored cable SIZE 3C x 2.5 sq mm

complete with necessary saddling and clamping

including providing and fixing GI Cable clamps, cable

glands and lugs at both ends as per specification

29 PHOTOLUMINICENT SIGNAGES Proving, Fixing and

Commissioning of VARIOUS Signage’s

30 RCC Under Ground Sump

Preparing structural design of RCC Under Ground /

Partially under ground / above high ground level

Reservoir of required capacity as per relevant I.S.

standards and constructing the same, including

excavation in all types of soil strata (including rock)

including shoring strutting if required, for loose soil /

to protect from collapse, casting 100 mm thick P.C.C.

levelling course in M15, Refilling the pit with proper

soil and disposing of the surplus stuff at all lead.

Including cement plaster in CM 1:2 with approved

water proofing compound to all over inside

container (i.e. walls, base, top slab/dome bottom

etc. all). Including all types of labour and material

charges of lowering, laying, erecting / hosting and

jointing of pipe assembly to inlet, outlet overflow,

washout and bye pass arrangement as per hydraulic

Providing and fixing accessories, CI Manhole frame

and cover, water level indicator, adequate cowl type

ventilators or lantern type ventilator with stainless

steel jail. RCC chambers for valves. Providing and

applying three coats of cement paint / snowcem to

the out side face of structure. It also includes

satisfactory water tightness test as per relevant I.S.

code and painting name of scheme and capacity on

the tank as per direction of engineer in charge.

List of Indian Standards for Design of GSR / SUMP:-

The structural design of GSR shall be in accordance

with provisions relevant I.S standards

(1) I.S. 3370 part I & II 2009 or Its latest revision

(1.1) I.S. 3370 part III & IV 1965 or Its latest revision

(2) I.S. 456 – 2000 or Its latest revision

(3) I.S. 1893 – 2000 – 1984 or Its latest revision.

(4) I.S. 875, Part – 1 to 3, 1987 or Its latest revision.

General Specifications:-

(1) Water depth in container shall be adopted as per

data of tender. Capacity shall be calculated excluding

free board of the reservoir. If water depth is not

specified, the suitable water depth / acceptable to

field engineer in accordance with hydraulic

requirement shall be adopted for capacity

(2) Shape of container (in plan) specified by in data

shall be adopted in absence circular shape shall be

(3) Size shall be fixed as per availability of space

(land area) at site / acceptable engineer in charge

(4) Effect of overlapping of pressure bulbs on soil

due near by structure and proposed sump should be

(5) Care shall be taken that no damage should occur

to nearby existing structure. Compensation shall be

paid for the same by agency.

(6) The minimum concrete grade for RCC shall be M-

(7) HYSD Fe 415 / 500 grade reinforcing bars

confirming to I.S. 1786 / 1139 shall be considered in

design. CRS / TMT bars shall be provided. In saline

atmosphere corrosion resistance stainless steel /

HCR rebar shall be provided. Any other steel can be

used with approval of C.E./ in situation of non

availability in market without extra cost.

(8) Minimum size (or thickness) of various

components shall be provided as per tender criteria

/ specifications in absence as per I.S./ Std. practice of

G.W.S.S.B. Minimum dimensions specified for

various components in tender data / specifications

shall be provided without fail.

(9) The safe bearing capacity (SBC) shall be referred

from SBC test report. In absence of report it shall be

referred from data sheet. If poor soil is found /

water table is met with during excavation SBC shall

be scientifically ascertained and design shall be

revise. No extra shall be paid for increase in

(10) DI pipes and special shall only be used if type is

not specified in tender

(11) The rate shall include cost of dewatering during

excavation making all arrangement when water

table meets within depth.

(12) The structure shall be designed properly to

resist uplift due to ground water table specified in

data or actual ground water table meets with during

excavation. If GWT / Uplift is mentioned in tender

and during excavation it dose not meet 7.5% rate

shall be reduced.

(13) SS pipes railing shall be provided over sump

perifery when sump height is ≥ 1.5 meter above

(14.a) RCC staircase/RCC Steps should be provided

from GL to sump top slab based on the height of the

GSR above/below the ground.

(14.b) RCC Staircase with SS railing to be provided

inside reservoir container. BB Masonry staircabin to

be provided to cover the same with MS safety door

having locking arrangement.

(15) Appearance of structure should be aesthetically

good looking acceptable to authority.

(16) Any change in size, shape, depth below GL,

height above GL, water depth, F.B., size of member

etc can be permitted in exceptional case due to site

condition or hydraulic design requirement by C.E. No

extra shall be paid for change.

(17) Any change in data, dimensions, shape, water

depth, reduction in size if permitted by competent

authority and if it reduces quantity then payment

shall be reduced prorate.

(18) When capacity of GSR / Sump is > 20 lakh litres

two or suitable compartments acceptable to

executive engineer shall be designed and provided.

(19) Agency shall engage qualified (at least graduate)

consulting engineer for designing the structure and

he / she shall visit the site for guidance of work.

(20) 75% part rate shall be payable for concrete,

reinforcement and plastering items of container

until satisfactory hydraulic testing for water

tightness is performed as per tender condition. Till

the work shall be treated as incomplete.

Above conditions / general specifications Sr. No. 1 to

20 are part and parcel of tender (contact) and

prevail over other provisions

As above without water table (Sub soil water level

below foundation)

Cost for 50000 litres capacity 1 Nos.

3 INSTALLATION OF FIRE FIGHTING SYSTEM AT F.P. NO. 138, BORSAD

No Description QTY. Per Amount

1 Providing ans supplying ISI mark GI Pipes with

coupling of following class and diameter including all

taxes insurances transportation freight charges

octroi inspection charges, loadinghg , unloading,

conveyance to departmental stores stacking etc

complete. 100 mm dia

2 Lowering laying and jointing GI pipes with GI specials

of following diameter in proper position grade and

allignment as directed by Engineer in charge

including conveyance from stores to site of work

labour given hydraulic testing etc complete. 100 mm

dia 153 34.34 RMT

3 Providing ans supplying ISI mark GI Pipes with

coupling of following class and diameter including all

taxes insurances transportation freight charges

octroi inspection charges, loadinghg , unloading,

conveyance to departmental stores stacking etc

complete. 80 mm dia

4 Lowering laying and jointing GI pipes with GI specials

of following diameter in proper position grade and

allignment as directed by Engineer in charge

including conveyance from stores to site of work

labour given hydraulic testing etc complete. 80 mm

dia 30 27.27 RMT

5 Providing and fixing 63 mm dia 15 mtr. long

rubberized fabric lined hose including SS male and

female instantaneous type coupling machine bound

with binding complete in all respects hose to IS:636

type-I and S.S. coupling to IS: 903 with ISI

certification. 7 8,585.00 Nos

6 Providing and fixing of 63 mm dia instantaneous

pattern SS short branch pipe, 20 mm dia nozzle

conforming to IS 903 with ISI mark, suitable for inter

connection to hose pipe coupling complete.

7 Providing, fixing and commissioning of Fire Hose BOX

Single door, fabricated from 22 gauge M.S sheet

(with glass) with locking and break glass recess for

key.: Installation, Testing & Commissioning of box of

size 450 mm x 600 mm x 250 mm (external use) with

stand of thickness 3 mm with 6 mm thick glazed

glass doors for housing the below mentioned items

with lockable glass doors, at desired location etc.

complete to accommodate landing Valve,1 No of

Long Hose Pipe, 1 Nos of Branch pipe mounted &

duly painted with Post officered externally and white

internally with synthetic enamel paint complete in

all respect, SS SINGLE HEADED HYDRANT VALVE: SITC

of fire hydrants as per IS 5290, consisting of 63 mm

dia, Single outlet flanged oblique type hydrant valve

with instantaneous female plunger type coupling,

chained blank cap in including making flanged joints

by providing necessary nuts, bolts, gaskets (4 mm

thick neoprene) all complete as suitable for 80 mm

dia stand post etc. all as per specification complete

8 SS SINGLE HEADED HYDRANT VALVE: SITC of fire

hydrants as per IS 5290, consisting of 63 mm dia,

Single outlet flanged oblique type hydrant valve with

instantaneous female plunger type coupling, chained

blank cap in including making flanged joints by

providing necessary nuts, bolts, gaskets (4 mm thick

neoprene) all complete as suitable for 80 mm dia

stand post etc. all as per specification complete as

9 HOSE REEL DRUM: SITC of Hose reel wall mounting

type drum completed with wall mounting bracket

complete with 20 mm x 30 mtr long, fitted with

mm SS 304 shut off nozzle with ball valve of 20 mm

confirming to IS :884 making connection to the

vertical riser by cutting welding, including providing

20mm dia shut off valve, all necessary piping,

fittings, fixing the hose reel with necessary anchor

fasteners by drilling holes in walls /RCC and in case

of yard line connection it must be comply with

support stand (MS Fabricated stand) making good

the same etc. all as per specification complete as

10 :Supply of Fire Brigade inlet with 4 nos 63mm dia

G.M. male hydrant connection including providing

and fixing 150mm dia Butterfly Valve PN 16 etc. for

the hydrant loop etc. all as per specification

complete as directed. 1 3,042.12 Nos

11 ABC TYPE POWDER FIRE EXTINGUISHER 6 KG

:Installation of portable fire extinguishers of 6 kg

capacity (dry powder - Class ABC ) suitable for wall

mounting including fixing the same with necessary

brackets / clamps / anchor bolts drilling holes

making good the same painting the surface as

required with ISI : 15683 etc. all as per specification

complete as directed. 14 2,878.50 Nos

CO2 TYPE FIRE EXTINGUISHER 4.5 KG :Installation &

Testing of portable fire extinguishers (CO2) of 4.5 kg

capacity confirming to IS : 2878 and certificate from

explosive dept. suitable for wall mounting including

fixing the same with necessary brackets / clamps /

anchor bolts drilling holes making good the same

painting the surface as required with ISI etc. all as

per specification complete as directed per

specification complete as directed

Cost of Horizontal type, multistage, centrifudgal,

solit cating pump with brinze impeller stainless steel

shaft, mechanical seal at a flow of 1620 lpm at 56 m

Head conforming to IS

Cost of 40 HP SQ Cage induction motor, TEFC,

Synchronous speed of 1500 RPM having class - 'F'

insulation and protection class IP 55 as per IS -

Cost of MS base plate coupling, coupling guard,

foundation bolts and anti vibration pads

14 Supply, installation, testing & commissioning of

V Fully automatic Microprocessor based soft starter

with external bypass arragement for pump control

application as per general specification as under

control method - torque control , input voltage -415

v, 3 phase , input frquency -50/60 Hz (+- 5%),

confirmative to standard - IEC 61947-4-2UL. CSA, CE,

Motor protection- inbuilt thermal protection, starter

protection- SC UV, Phase unbalance, Phase failure,

EMC Std-IEC 61000-4-2 Level 3 & IEC 61000-4-3

LEVEL-3. bUILT IN COMMUNICATION AS PER rs

ELECTRICALS FOR FIRE HYDRANT SYSTEM Supply of

Power cabling and control cabling from Fire pump

controller to Fire Pumps etc. all as per specification

complete as directed. Item also includes supply of

Main Incomer Cable from Main Electrical Panel to

Main Fire Panel in Pump House double earthing for

pumps instruments, panels etc. (cable 4 core x

Providing, fixing, testing & commissioning of 100 mm

dia Burden type, Stainless Steel dial type pressure

gauge (in Pump Room) including brass isolation valve

and pipe having calibration of 0-16 Kg/cm2. : Supply

of pressure gauges of suitable range for pump sets

with ball valves, siphon, and fittings like unions/

collars/ reducers etc. NOTE: Pressure range 0-20 bar

etc. all as per specification complete as directed.

Providing and fixing C.I. Butterfly valve, water type

class PN 1.6 as per IS: 13095 , including necessary

nuts, bolts, gaskets etc. with flanges as required,

complete in all respects. For 100 mm nominal bore.

:Supply of 100 mm dia. lever operated slim seal type

CI butterfly valves with ss disc conforming to IS-

13095 of PN 1.6 rating along with its all accessories

such as flanges, nut-bolt-washers, gaskets etc. at

shown location including making suitable fixing

arrangement & carrying out all related works etc. all

as per specification complete as directed.

Providing and fixing pressure switch KP- 36 (for

operation at 0-15 Kg. /sqcm) with required fittings

and accessories complete. : Supply of pressure

switch for auto-operation of all pumps in sequences

(with cable approx. 4X10 MTR) etc. all as per

specification complete as directed.

Supply and installation of 100 mm nominal bore.

Foot Valve (Heavy Duty, Non-Return Type) with built-

in strainer, suitable for pump suction line. Ensures

prevention of backflow, maintains pump priming,

and protects the pump from debris and damage

20 M S STRUCTURAL STEEL FOR SUPPORTS M S

STRUCTURAL STEEL FOR SUPPORTS: Supply of MS

steel for supports of fire hydrant network going

along with the MS structure of plant or from the wall

for support etc. all as per specification complete as

directed. 75 232.30 Kg

Providing and supplying ISI mark CI D/F Reflux Valves

as per IS:5312 [Latest Edition) of following class and

diameter including all taxes, Insurance,

transportation, freight charges, octroi, inspection

charges, loading, unloading. conveyance to

departmental stores, stacking etc. complete 100 mm

Dia Reflux valves PN 1.0 IS 5312 with ISI mark

Lowering, laying and jointing in position following C.

I. / D/F Reflux valves, Butterfly valves, Sluice valves

and Air valves including cost of all labour, jointing

material, including nut bolts and giving satisfactory

hydraulic testing, etc. complete. Sluice valves,

Butterfly Valves, Reflux Valves

23 Supply, installation, testing and commissioning of Air

Release valve of size as mentioned in the item. :

Supply of Suitable G.M... Air release valve of 25mm

dia PN 16 all as per specification complete as

directed. 2 724.17 Nos

24 Supply and Installation of 2 zone conventional fire

alarm panel with Battery back up 2 No 1 27,270.00 Nos

25 MANUAL CALL POINT MANUAL CALL POINT Supply,

Installation, testing and commissioning of

conventional type manual call point 6 808.00 Nos

26 HOOTERS Supply, Installation, testing and

commissioning of conventional type hooters 6 808.00 Nos

27 FIRE ALARM CABLE Providing, fixing, testing and

commissioning of Red Colour 2 Core X 1.5 Sqmm

Flexible copper FRLS Cable .Item includes providing

and fixing cable accessories complete as per

specifications and as per NBC/IS/Engineer In charge

requirements 275 145.44 Rmt

CABLE Providing and fixing PVC insulated copper

conductor armored cable SIZE 3C x 2.5 sq mm

complete with necessary saddling and clamping

including providing and fixing GI Cable clamps, cable

glands and lugs at both ends as per specification

29 PHOTOLUMINICENT SIGNAGES Proving, Fixing and

Commissioning of VARIOUS Signage’s

30 RCC Under Ground Sump

Preparing structural design of RCC Under Ground /

Partially under ground / above high ground level

Reservoir of required capacity as per relevant I.S.

standards and constructing the same, including

excavation in all types of soil strata (including rock)

including shoring strutting if required, for loose soil /

to protect from collapse, casting 100 mm thick P.C.C.

levelling course in M15, Refilling the pit with proper

soil and disposing of the surplus stuff at all lead.

Including cement plaster in CM 1:2 with approved

water proofing compound to all over inside

container (i.e. walls, base, top slab/dome bottom

etc. all). Including all types of labour and material

charges of lowering, laying, erecting / hosting and

jointing of pipe assembly to inlet, outlet overflow,

washout and bye pass arrangement as per hydraulic

Providing and fixing accessories, CI Manhole frame

and cover, water level indicator, adequate cowl type

ventilators or lantern type ventilator with stainless

steel jail. RCC chambers for valves. Providing and

applying three coats of cement paint / snowcem to

the out side face of structure. It also includes

satisfactory water tightness test as per relevant I.S.

code and painting name of scheme and capacity on

the tank as per direction of engineer in charge.

List of Indian Standards for Design of GSR / SUMP:-

The structural design of GSR shall be in accordance

with provisions relevant I.S standards

(1) I.S. 3370 part I & II 2009 or Its latest revision

(1.1) I.S. 3370 part III & IV 1965 or Its latest revision

(2) I.S. 456 – 2000 or Its latest revision

(3) I.S. 1893 – 2000 – 1984 or Its latest revision.

(4) I.S. 875, Part – 1 to 3, 1987 or Its latest revision.

General Specifications:-

(1) Water depth in container shall be adopted as per

data of tender. Capacity shall be calculated excluding

free board of the reservoir. If water depth is not

specified, the suitable water depth / acceptable to

field engineer in accordance with hydraulic

requirement shall be adopted for capacity

(2) Shape of container (in plan) specified by in data

shall be adopted in absence circular shape shall be

(3) Size shall be fixed as per availability of space

(land area) at site / acceptable engineer in charge

(4) Effect of overlapping of pressure bulbs on soil

due near by structure and proposed sump should be

(5) Care shall be taken that no damage should occur

to nearby existing structure. Compensation shall be

paid for the same by agency.

(6) The minimum concrete grade for RCC shall be M-

(7) HYSD Fe 415 / 500 grade reinforcing bars

confirming to I.S. 1786 / 1139 shall be considered in

design. CRS / TMT bars shall be provided. In saline

atmosphere corrosion resistance stainless steel /

HCR rebar shall be provided. Any other steel can be

used with approval of C.E./ in situation of non

availability in market without extra cost.

(8) Minimum size (or thickness) of various

components shall be provided as per tender criteria

/ specifications in absence as per I.S./ Std. practice of

G.W.S.S.B. Minimum dimensions specified for

various components in tender data / specifications

shall be provided without fail.

(9) The safe bearing capacity (SBC) shall be referred

from SBC test report. In absence of report it shall be

referred from data sheet. If poor soil is found /

water table is met with during excavation SBC shall

be scientifically ascertained and design shall be

revise. No extra shall be paid for increase in

(10) DI pipes and special shall only be used if type is

not specified in tender

(11) The rate shall include cost of dewatering during

excavation making all arrangement when water

table meets within depth.

(12) The structure shall be designed properly to

resist uplift due to ground water table specified in

data or actual ground water table meets with during

excavation. If GWT / Uplift is mentioned in tender

and during excavation it dose not meet 7.5% rate

shall be reduced.

(13) SS pipes railing shall be provided over sump

perifery when sump height is ≥ 1.5 meter above

(14.a) RCC staircase/RCC Steps should be provided

from GL to sump top slab based on the height of the

GSR above/below the ground.

(14.b) RCC Staircase with SS railing to be provided

inside reservoir container. BB Masonry staircabin to

be provided to cover the same with MS safety door

having locking arrangement.

(15) Appearance of structure should be aesthetically

good looking acceptable to authority.

(16) Any change in size, shape, depth below GL,

height above GL, water depth, F.B., size of member

etc can be permitted in exceptional case due to site

condition or hydraulic design requirement by C.E. No

extra shall be paid for change.

(17) Any change in data, dimensions, shape, water

depth, reduction in size if permitted by competent

authority and if it reduces quantity then payment

shall be reduced prorate.

(18) When capacity of GSR / Sump is > 20 lakh litres

two or suitable compartments acceptable to

executive engineer shall be designed and provided.

(19) Agency shall engage qualified (at least graduate)

consulting engineer for designing the structure and

he / she shall visit the site for guidance of work.

(20) 75% part rate shall be payable for concrete,

reinforcement and plastering items of container

until satisfactory hydraulic testing for water

tightness is performed as per tender condition. Till

the work shall be treated as incomplete.

Above conditions / general specifications Sr. No. 1 to

20 are part and parcel of tender (contact) and

prevail over other provisions

As above without water table (Sub soil water level

below foundation)

Cost for 50000 litres capacity 1 Nos.

Obtaining NOC From authority

Add 3 % Cont. & Superv. :

BORSAD NAGAR PALIKA

Name of Work:- Providing General Type Rain Water Harvesting System At FP. No 138 Tp Scheme No. 2 At Borsad.

No Description Quantity Total Rate Per Amount

Rain Water Harvesting System

1 Drilling of pilot bore hole in Pilot 300/250mm drilling alluvial strata

by direct rotary rig / reverse rotary rig. 90.00 764.05 Mtr.

2 Remaining of 400mm dia. reaming bore hole including assembling,

jointing, lowering of housing casing, screen pipes & other

assembly items with gravel packing and clay balls packings

etc.complete. 90.00 234.62 Mtr.

3 Manufacture, supply & delivery of ISI marked UPVC Casing pipe (IS

with latest amendment. (b) 200mm nominal dia. CM Type. 90.00 1473.02 Mtr.

4 Best quality of well sorted sevaliya gravel of size 4mm to 6mm at

site if work including loading, unloading, carting etc.complete.

5 Clamp made from MS Plate with 3 holes on either side with nuts

and bolts of standard and suitable size, 750 x 75 x 16mm flat to

200mm dia. Pipe. 2.00 1660.43 Pair

6 Bore plug having 100 mm height made from M.S. plate with

holes at equal distance on circumference for nut-bolts type,

locking arrangement with nuts-bolts & lock nuts of std. Make

complete. Bore plug having 100mm height made from UPVC of

std. make Suitab 1.00 561.92 Nos.

7 providing and fixing concealed center point to wall ceiling & floor

cpvc (SDR13.5) PIPE having national sanitation foundation (NSF)

seal for potable water of following dia.nominal bore tube fitting

and clamps including making good the wall, celing and flo

8 Excavation for pipeline trenches for water supply, sewerage line,

manhole etc. all with shoring and struting if required as per

required gradient and line including safety provision using site rails

and stacking excavated stuff including up to all require

b) In hard murrum, boulders incl. macadam road - 1.50 mtr. To

3.00 mtr. depth. 476.42 150.97 Cu.Mtr.

9 Providing and casting in situ mass cement concrete in 1:4:8

proportion using granite quartzite trap metal of size 25mm to

40mm including consolidation curing etc. complete. 1.06 3461.20 Cu.Mtr.

10 Refilling the pipeline trenches incl. ramming, watering,

consolidating desposal of surplus stuff as directed within a radius

of 3 Km. 12.59 22.44 Cu.Mtr.

11 Providing and casting in situ C.C. in grade M-20 (proportions as per

mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6mm to 20mm

of RCC work, including scaffolding centering, formwork, nee

12 Providing and casting in situ C.C. in grade M-20 (proportions as per

mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6mm to 20mm

of RCC work, including scaffolding centering, formwork, nee

13 Providing and casting in situ C.C. in grade M-20 (proportions as per

mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6mm to 20mm

of RCC work, including scaffolding centering, formwork, nee

14 Supply cutting, bending, binding and placing in position steel as

per plan and design and as per ISS 2502 including cost of steel and

binding wire for reservoirs / structures only including lift up to

meter height or depth below GL for all diameters - T

15 Cement plaster 20mm thick in C.M. 1:2 using water proofing

compound of approved quality including finishing etc. complete.

16 R.C.C. precast manhole, frame and cover, manufacture, supply and

delivery at store or site of work precast R.C.C. frame and cover

(M200), suitable to drainage manhole and as per type design and

drawing including cost of reinforcement, MS angles or flat, c

> Frame 3.00 1143.53 Nos.

> Cover 3.00 1196.58 Nos.

17 Providing & Supplying the filter sand/Gravel of specified effective

size (0.45 to 0.70 mm) and uniformity coefficient( not more than

1.7, nor less than 1.3) and laying over gravel support conforming

to IS : 8491 (i) – 77 in filter bed of required depth a

18 Providing & supplying ISI standard NP3 class Rmt. R.C.C. Pipes (of

sulphate resisting Cement) in standard lengths of following class

and diameter suitable for either collar joints or rubbing ring. joints

including all taxes, insurance, transportation, fre

19 Providing, Supplying, Lowering and Laying in standard length ISI

mark rigid unplasticised PVC pipes suitable for potable water with

ring fit joint including cost of rings, as per IS Specification no.

4985/1988 including all local and central taxes, transp

20 Testing of Recharge Pit by emptying a tanker of Nos. 8000 Land

measuring the time as per the specifications and reporting of the

same 1.00 707.00 Nos.

21 For Genreal Area: Horizontal Filtration Module Nos. is Precast

Modular Step well of M25 grade, designed to capture sediments

primarily from surface runoff water. This Octagonal shape

structure has a circumscribing diameter of approximately 918mm

and a hei 1.00 104030.00 CMT

22 For Genreal Area: Sand Filtration Module M-25 Nos. grade cement

concrete system for rainwater harvesting with SS 304 screen and

natural filters. It consists of single module with internal volume of

approximately 0.8 cubic metres that is to be fixed below

23 Submission and approval of survey. Job Hydrogeological

investigations at number of locations in Chhotaudepur City,

working Drawings including all layout sections, typical details, shop

drawings, As-built drawings and submission of working drawings

and imp 1.00 18493.10 JOB

24 Jobwork for cleaning of modules for every Job. Premonsoon for

once in years with inbuilt Intergral ladder at 1125mm with safety

by water cleaning system labours, hand bucket, lari & other tools

ie. Trikam, Pavda, Rassa, Battery. G.T. Salia etc.with dispos

3.00% Supervision & Contigency :