Construction of Office, Store and Security room at Sri Annapurna Sametha Sri Kasi Visweswara Swamy temple and Sri Prayaga Madava Swamy Temple at Bugga, Nagari, Chittoor District

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. - Ordinary soil-Manual means up to 3m depth

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Cement Concrete C.C. (1:4:8) using 40 mm ( 0.54 cu.m), 20mm (0.27 cu.m) and 12 mm (0.09 cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete.

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC)etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department but excluding cost of centering, shuttering charges and excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)

Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kgs/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

RCC M- 20 Design mix using 20mm HBG crushed metal 0.480 cu.m , 10mm HBG crushed metal 0.320 cu.m , sand 0.400 cu.m and cement 350 kg with water cement ratio of 0.53 (185.5 Lit per cu.m of CC ) etc.horizontal plain sunshades or lofts projecting from the face of the wall 65mm average thickness,80mm thick at the face of the wall and 50mm thick at the free end and cast monolithically with the lintels or tailed to the full thickness of the wall where there are no lintels using 20mm size graded machine crushed hard granite metal (coarse aggregate) from any source conforming to the relevant ISI standards including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing , etc.,complete, but excluding cost of centering charges and excluding cost of steel and its fabrication charges for finished item of work.-do- 0.6 mts width Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix if mixing is done by volume mixing.

Supply and placing of the M20 Design Mix using of 10mm HBG crushed metal 0.480cu.m,6mm HBG Crushed metal 0.320cu.m,sand 0.400cu.m and cement 350Kg with water cement ratio of 0.53(185.50 ltrs/cu.m of CC) etc., from any source confirming to the relevant ISI standard including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of steel and its fabrication charges, centering charges, shuttering charges for finished item of work (APSS No. 402) Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix if mixing is done by volume mixing. RCC M20 design mix precast slabs using 10 mm graded aggregate of HBG crushed metal from any approved quarry with necessary reinforcement excluding cost of steel and tying of grills, centering charges but including cost of necessary form work and cost and conveyance of all materials curing as directed by the department.-do- 40 mm thick.

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars below 36 mm Fe 500/Fe-500D/Fe550 of specified grade (as per IS 1786 - 2008) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire,2 nos of 20G binding wire in tandem are to be strictly adhered). Note: Unless otherwise fabrication and placement of steel, no pre-pament shall be made against the supply of steel reinforcement

Cement Concrete (1:3:6) using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete. Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Construction of Brick Masonry in CM (1:5) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm)including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick partition walls in CM (1:4) using well burnt bricks 2nd class or ground moulded (Non modular or traditional size) bricks (230X110X70 mm) including curing, cost and conveyance of all materials etc,. Complete

Plastering in Cement mortar using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete for the following proportions

-do- in CM (1:5), 12mm thick

-do- in CM (1:5), 20mm thick

Providing and fixing of door frame made from cold roll formed sections made of galvanized (Base steel as per IS277 with zinc of 120 Gms/sqm) colour coated steel sections with total coated thickness of 1mm, primer coated with epoxy primer coat of 5-7 microns thick, finish paint with polyester paint of 12-16 microns. The Section for door frame is to be filled with polyurethane (P.U) form of 40kg/m3. Overall size of frame section should be of 50mm x 50mm. With necessary corner brackets, stiffeners,hinges, and screws. Cement Bonded particle board shutter “Single Leaf” with all round styles “U” section of size 12m x 18m x 12mm made from 0.6 mm thick galvanized, colour coated cold rolled steel profiles with 16mm thick Cement Bonded particle Board with necessary screws fixed at every 1’-0” (304.8mm) intervals. The cost inclusive of MS nickel coated Aldrop of size 250mm long 2nos.200mm long tower bolt 1no., 125mm handles 2nos., cost and conveyance of all materials at site and applying one coat primer , one coat of luppum and two coats of synthetic enamel paint as per approved design for finished item of work DOORS FRAMES (COLOUR COATED STEEL SECTIONS) & SHUTTER USING CEMENT BONDED PARTICLE BOARD AS PER IS 14276:

Supply and fixing of pre-painted steel openable windows base steel as per IS 513 of -0.58 mm thick 'D" quality, galvanized as per IS 277 , finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer, section for outer frame of 46 x 52 mm section and for shutter of 46 x 46 mm section for mullion 46 x 70 mm, and section for beading should be 18 x 25 mm with 5 mm thick plain float glass fitted with Ethyl propylene Diamine monomer Gasket (EPDM) and handle made of high grade aluminium powder coated with frames fixed to the concrete /masonry wall by means of self expanding screws including 10 mm square guard bars with 6" pitch complete for finished item of work . -do- Windows: Double shutter 3'-0" x 4'-0" (914.4mm x 1219.2 mm) outer frame section size of 46 x 52 mm shutter frame section size of 46 x 46 mm

Supply of Mild steel ( Powder coated ) Aldrop (IS 2681) 300 mm Long

Supply of Mild steel ( Powder coated ) Door handles IS 208 125 mm long

Supply of Mild steel (Powder coated) tower bolts 10 mm dia (IS 204) 10 mm x 150 mm long

Supply of Mild steel (Powder coated) tower bolts 10 mm dia (IS 204) 10 mm x 100 mm long

Supply of Mild steel ( Powder coated ) Butt hinges (IS 205) 125 mm long

Supply of Mild steel ( Powder coated ) Butt hinges (IS 205) 75 mm long

Supplying, Fabrications and placing in position with Mild Steel Tubes & pipes of all diameters as per IS-1161 for truss work including cutting weldin, grinding, finishing & placing inposition for required spans including cost of fabrication charges welding rods, power charges and erecting in position and fixing by using chain pully blocks derek pole arrangement and cranes etc., complete as directed by the department.

Flooring with soluble salt porcelain vitrified tiles screen printed and polished of size 600 x 600 mm and thickness between 8- 10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & joints with spacer joints with 3 mm wide jointed neatly with filer material of cement/epoxy grout/white cement paste to full depth mixed with pigment of matching shade as directed during execution, including cost and conveyance of all materials, etc., complete - for finished item of work.

Supply and fixing of Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47mm thickness, Coating: Alu-Zinc coating AZ150 GSM. Tensile Strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting Thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc.,complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW)

Painting two coats for new iron work with ready mixed Synthetic Enamel paints in all shades Grade-I having VOC (Volatile Organic Compound) content less than 50 grams/ liter over primer coat of Red Oxide Primer Paint of Grade -1 (total three coats) of approved make and colour including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

Painting two coats for new plastered surface with acrylic emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/ liter over primer coat of water based Cement Primer of Interior Grade- 1 (total three coats) of approved make and colour including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

Painting two coats for new plastered surface acrylic emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound ) content less than 50 grams/ liter over primer coat of water based Cement Primer of Exterior Grade- 2 (total three coats) of approved make and colour including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint Gr-I over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. - Ordinary soil-Manual means up to 3m depth

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Cement Concrete C.C. (1:4:8) using 40 mm ( 0.54 cu.m), 20mm (0.27 cu.m) and 12 mm (0.09 cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete.

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC)etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department but excluding cost of centering, shuttering charges and excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)

Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kgs/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

RCC M- 20 Design mix using 20mm HBG crushed metal 0.480 cu.m , 10mm HBG crushed metal 0.320 cu.m , sand 0.400 cu.m and cement 350 kg with water cement ratio of 0.53 (185.5 Lit per cu.m of CC ) etc.horizontal plain sunshades or lofts projecting from the face of the wall 65mm average thickness,80mm thick at the face of the wall and 50mm thick at the free end and cast monolithically with the lintels or tailed to the full thickness of the wall where there are no lintels using 20mm size graded machine crushed hard granite metal (coarse aggregate) from any source conforming to the relevant ISI standards including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing , etc.,complete, but excluding cost of centering charges and excluding cost of steel and its fabrication charges for finished item of work.-do- 0.6 mts width Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix if mixing is done by volume mixing.

Supply and placing of the M20 Design Mix using of 10mm HBG crushed metal 0.480cu.m,6mm HBG Crushed metal 0.320cu.m,sand 0.400cu.m and cement 350Kg with water cement ratio of 0.53(185.50 ltrs/cu.m of CC) etc., from any source confirming to the relevant ISI standard including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of steel and its fabrication charges, centering charges, shuttering charges for finished item of work (APSS No. 402) Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix if mixing is done by volume mixing. RCC M20 design mix precast slabs using 10 mm graded aggregate of HBG crushed metal from any approved quarry with necessary reinforcement excluding cost of steel and tying of grills, centering charges but including cost of necessary form work and cost and conveyance of all materials curing as directed by the department.-do- 40 mm thick.

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars below 36 mm Fe 500/Fe-500D/Fe550 of specified grade (as per IS 1786 - 2008) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire,2 nos of 20G binding wire in tandem are to be strictly adhered). Note: Unless otherwise fabrication and placement of steel, no pre-pament shall be made against the supply of steel reinforcement

Cement Concrete (1:3:6) using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete. Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Construction of Brick Masonry in CM (1:5) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm)including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick partition walls in CM (1:4) using well burnt bricks 2nd class or ground moulded (Non modular or traditional size) bricks (230X110X70 mm) including curing, cost and conveyance of all materials etc,. Complete

Plastering in Cement mortar using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete for the following proportions

-do- in CM (1:5), 12mm thick

-do- in CM (1:5), 20mm thick

Providing and fixing of door frame made from cold roll formed sections made of galvanized (Base steel as per IS277 with zinc of 120 Gms/sqm) colour coated steel sections with total coated thickness of 1mm, primer coated with epoxy primer coat of 5-7 microns thick, finish paint with polyester paint of 12-16 microns. The Section for door frame is to be filled with polyurethane (P.U) form of 40kg/m3. Overall size of frame section should be of 50mm x 50mm. With necessary corner brackets, stiffeners,hinges, and screws. Cement Bonded particle board shutter “Single Leaf” with all round styles “U” section of size 12m x 18m x 12mm made from 0.6 mm thick galvanized, colour coated cold rolled steel profiles with 16mm thick Cement Bonded particle Board with necessary screws fixed at every 1’-0” (304.8mm) intervals. The cost inclusive of MS nickel coated Aldrop of size 250mm long 2nos.200mm long tower bolt 1no., 125mm handles 2nos., cost and conveyance of all materials at site and applying one coat primer , one coat of luppum and two coats of synthetic enamel paint as per approved design for finished item of work DOORS FRAMES (COLOUR COATED STEEL SECTIONS) & SHUTTER USING CEMENT BONDED PARTICLE BOARD AS PER IS 14276:

Supply and fixing of pre-painted steel openable windows base steel as per IS 513 of -0.58 mm thick 'D" quality, galvanized as per IS 277 , finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer, section for outer frame of 46 x 52 mm section and for shutter of 46 x 46 mm section for mullion 46 x 70 mm, and section for beading should be 18 x 25 mm with 5 mm thick plain float glass fitted with Ethyl propylene Diamine monomer Gasket (EPDM) and handle made of high grade aluminium powder coated with frames fixed to the concrete /masonry wall by means of self expanding screws including 10 mm square guard bars with 6" pitch complete for finished item of work . -do- Windows: Double shutter 3'-0" x 4'-0" (914.4mm x 1219.2 mm) outer frame section size of 46 x 52 mm shutter frame section size of 46 x 46 mm

Supply of Mild steel ( Powder coated ) Aldrop (IS 2681) 300 mm Long

Supply of Mild steel ( Powder coated ) Door handles IS 208 125 mm long

Supply of Mild steel (Powder coated) tower bolts 10 mm dia (IS 204) 10 mm x 150 mm long

Supply of Mild steel (Powder coated) tower bolts 10 mm dia (IS 204) 10 mm x 100 mm long

Supply of Mild steel ( Powder coated ) Butt hinges (IS 205) 125 mm long

Supply of Mild steel ( Powder coated ) Butt hinges (IS 205) 75 mm long

Supplying, Fabrications and placing in position with Mild Steel Tubes & pipes of all diameters as per IS-1161 for truss work including cutting weldin, grinding, finishing & placing inposition for required spans including cost of fabrication charges welding rods, power charges and erecting in position and fixing by using chain pully blocks derek pole arrangement and cranes etc., complete as directed by the department.

Flooring with soluble salt porcelain vitrified tiles screen printed and polished of size 600 x 600 mm and thickness between 8- 10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & joints with spacer joints with 3 mm wide jointed neatly with filer material of cement/epoxy grout/white cement paste to full depth mixed with pigment of matching shade as directed during execution, including cost and conveyance of all materials, etc., complete - for finished item of work.

Supply and fixing of Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47mm thickness, Coating: Alu-Zinc coating AZ150 GSM. Tensile Strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting Thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc.,complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW)

Painting two coats for new iron work with ready mixed Synthetic Enamel paints in all shades Grade-I having VOC (Volatile Organic Compound) content less than 50 grams/ liter over primer coat of Red Oxide Primer Paint of Grade -1 (total three coats) of approved make and colour including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

Painting two coats for new plastered surface with acrylic emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/ liter over primer coat of water based Cement Primer of Interior Grade- 1 (total three coats) of approved make and colour including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

Painting two coats for new plastered surface acrylic emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound ) content less than 50 grams/ liter over primer coat of water based Cement Primer of Exterior Grade- 2 (total three coats) of approved make and colour including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint Gr-I over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.