E.T.No.-EDC(USN)32/2025-26

Amount

Annexure-A (LABOUR CHARGES)

Earthing of support with M.S. Earth rod of 2.5 meter long by hammaring of M.S. Rod to proper depth and connecting the earth electrode with the help of G.I. wire as per construction manual.

Erection of SP-55 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual.

Erection of Sp-55 double support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual

Grouting of pole in size 0.45x4.45x1/9 of the support in CC ration 1:4:8(1 cement:4 graded stone20 mm niminal size: 8 coarse sand) block including cost of cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, levelling as per RESPO cnstruction manual

Muffing of poles size 0.45x0.60 cm radius with 1:3:6(1 cement:3 coarse sand :graded stone 10 mm nominal size) block size 45 cm height from ground level including cost of cement,stone and sand etc.

Dismantling of existing HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store (ACSR Weasel)

Painting of SP-55 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Cement Plaster on side walls in 1:4 ratio on DTR Plinth.

Erection, providing and fixing of wire mesh of size 50x35 mm around plinth and toe wall duly welded with frame of M.S angle iron 35 x35x6 mm and strip of size 35x6 mm in mid of each side along with wire mesh (width of wire mesh 1.5 meter) with the height of 0.5 meter above the plinth and 2 meter above the toe wall with 1 No. gate and locking arrangment in the toe wall size including grouting of 6 Nos. legs in the ratio in block of size 0.25x0.25x0.45 meter including gravlling of shingle of size 20 to 40 mm and complete painting of wire mesh with aluminium paint with two coat (Including the cost of cement and all material).

Installation / mounting of new 400 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all connections of HT and LT side and its complete commissioning.

Installation / mounting of new 250 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all connections of HT and LT side and its complete commissioning.

Laying, Spreading, Stringing and sagging of 11 KV/33 KV line in 3 phase (3 Phase 3 wire) of ACSR Dog as phase wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Providing and fixing of Danger Board and number plate complete by providing clamps of M.S. Flat 50x6 mm and Nuts & Bolts, danger Boards of M.S. Sheet 2 mm Thick 11''x7'' size (Including cost of all material).

Cartage of ST pole SP-55 Poles from store centre to construction site with loading, unloading at both points and proper stacking. (Distance 0-20 Km)

Cartage of other material (other than poles) by vehicle from Store Center to nearest construction site Store including loading and unloading at both ends (distance 0-20 Km)

Cartage of the 250 KVA transformer from store center to construction site with loading and unloading at both points.(Distance 0- 20 Km)

Cartage of the 400 KVA transformer from store center to construction site with loading and unloading at both points.(Distance 0- 20 Km)

Opening and Making of Jumpher of Section Pole.

Earthing of distribution transformer including digging of pit of size 2.5 Mtr depth and make hole of size 150 mm. Placing of earthing electrode (to be supplied by contractor), connecting the same with G.I. Strip (to be supplied by contractor) of size 35x6 mm for a minimum lenght 6 m. treatment of soil with highly condctive substance as per IS 30343 complete in all respect, result of earthing resistance to be recroded in M.B. before and after installation of earthing. The earth resistance after earthing should be less than 1 Ohm.

Laying of LT cable and making connection at T/F LT bushing/LT pole with lug if required as per requirement.

Excavation of earth for stay pit of size 0.6x0.6x1.2 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work.

Annexure-B (SUPPLY ITEMS)(As per UPCL Norms)

Supply of Steel Tubular Poles 11 m long (STP 11.0 M, 410 MPa , SP-55) as per IS 2713 (Parts 1 to 3): 1980 (Bottom Portion hot dip galvanized) with MS Plate (300ɸx6).

Supply of MS Channel 100x50 mm.

Supply of 11 KV Polymer Disc Insulator (B&S) Type.

Supply of 11 KV Polymer PIN Insulator with PIN.

Supply of Disc Fit. B&S Type Dog/Racoon 70 KN

Supply of X Arm Angle 65x65x6 mm V Type 11 KV.

Supply of Earthing Rod MS 20x2500 mm.

Supply of GI wire 5mm/6 SWG.

Supply of Stay set GI 16x1800 mm.

Supply of Stay Wire GI 7/3.15MM/ 7/10SWG

Supply of ACSR Dog Conductor.

Supply of LT XLPE Cable 1x400 Sq.MM.

Supply of LT XLPE Cable 1x70 Sq.MM

Supply of MS Holding Clamps.

Supply of X Arm Clamp for ST Pole SP-55 with N/B.

Supply of F-Clamp.

Supply of double Pole Clamps with N/B for SP-55

Supply of Stay Insulator.

Supply of PG clamp Dog to Dog.

Supply of Stay clamp for SP-55 with Nut & Bolt.

Supply of Al. LUG Crimping (400) Sq.MM

Supply of Stone Pad 300x300x75 mm.

MANRAJ ELECTRICAL & INFRASTRUCTURE (BID ID -403331)

PERFECT ELECTRICALS AND ENGINEERS (BID ID -403166)