Proposed Construction of Swimming Pool at T.P.-128, F.P.-493 in Vatva Ward, South Zone, Ahmedabad

Estimated cost put to tender : Rs. 17,68,87,111.46 Estimated cost put to tender : Rs.

Add_____% Above : Rs ___________ Add_____% Below : Rs ___________

Total : Rs___________ Total : Rs___________

In words : Rupees _______________________ In words : Rupees _______________________

The contractor should get the sample of material in respect of quality and source of supply or manufacturer approved by

Consultant / AMC in all cases. All such approved samples should be kept at site in the custody of EIC-CMC/PMC/AMC.

Note-1 The tests for the make in external laboratory in presence of CMC/PMC/AMC to be carried out by Contractor at his own

cost as per relevant latest codes. Reinforcement steel & cement original purchase bills shall be produced to

CMC/PMC/AMC as and when asked for.

Note-2 Rate includes for any height, any level, any lead & lift and as per directed by EIC.

Note-3 For Fire Fighting System Autoglow Mandatory Sinages and NOC Process and charges of NOC are included.

Signature of Contractor Additional City Engineer

Seal South Zone

Date Ahmedabad Municipal Corporation

Ahmedabad Municipal Corporation

Proposed Construction of Swimming Pool at T.P.-128, F.P.-493 in Vatva Ward, South Zone, Ahmedabad.

BOQ of Civil, Site Development & Plumbing Work

Item Description Unit Rate Amount

(A) Excavation & Earthwork

Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and trees girth up to 300 mm removal

1 of stumps of trees cut earlier and disposal of unserviceable materials Sqm 7,889.00 2.81

(C) By mechanical means in area of light jungle

Excavation for foundation for depth upto 1.5 m including sorting out and stacking of useful materials and disposing off the excavated

2 stuff upto 50 Meter lead. Cum 11,823.00 148.19

(A) Dense or Hard Soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the

3 excavated stuff upto 50 Meter lead. Cum 9,554.00 160.77

(B) Dense or Hard Soil

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing off the

4 excavated stuff upto 50 Meter lead. Cum 6,091.00 172.50

(C) Dense or Hard Soil

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth

consolidating each disposited layer by ramming and watering.

6 Filling in plinth with sand under floors including watering, ramming, consolidating and dressing etc. completed Cum 360.00 455.63

Filling in plinth with murrum or selected soil in layers of 20 cm. thickness including watering, ramming and consolidating etc.

Complete. (brought from out side)

Providing and laying rubble soling, 230 mm thick, in a compact manner,foudation, road, footpath etc. using 200 to 230 mm. cut size

8 stones including filling the gaps with 40mm metal and packing with stone chips with murrum covering and levelling the surface after Cum 1,964.00 2,035.00

filling the voids including watering, ramming well and consolidating each layer, as directed by EIC.

Conveyance charges of lime murrum building rubbish earth, manuar of sludge and excavated rock,fly ash & surplus excavated earth

9 from site as directed by etc. complete as directed by EIC. Cum 2,468.00 320.73

A) Upto 5.00 Km.

(B) PCC & RCC Work

Provdg. & laying cement concrete 1:2:4 (1cement:2 corse sand :4 broken stone aggregate 20 mm nominal size) and curing complete

11 including cost of form work in Cum 1,688.00 3,661.30

(A) Foundation and plinth

Providing, laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding reinforcement

for reinforced concrete work in: Up to Plinth Level. (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

Item Description Unit Rate Amount

Providing, laying controlled cement concrete M 300 and curing complete including the costExcavation

of form work&but excluding reinforcement

for reinforced concrete work in: Up to Plinth Level. (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

Providing, laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding reinforcement

14 for reinforced concrete work in: Column (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be paid) Cum 283.00 7,373.00

(1) Column up to Ground Floor slab

Providing, laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding reinforcement

15 for reinforced concrete work in: Column (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be paid) Cum 41.00 7,413.00

2) Column First Floor

Providing, laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding reinforcement

16 for reinforced concrete work in: Column (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be paid) Cum 13.00 7,453.00

3) Column Second Floor

Providing, laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding reinforcement

for reinforced concrete work in: Up to Plinth Level. (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

(A) Plinth beam

Providing and laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in: Beam (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

1) Floor beam Ground Floor

Providing and laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in: Beam (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

2) Floor beam First Floor

Providing and laying controlled cement concrete M 250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in: Beam (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

3) Floor beam Second Floor

Providing, laying controlled cement concrete M 300 and curing complete including the cost of form work but excluding reinforcement

21 for reinforced concrete work in:RCC wall (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be paid) Cum 229.00 7,344.00

1) RCC wall up to Ground floor slab

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in: Grade Slab

Item Description Unit Rate Amount

Providing and laying controlled cement concrete M-250 and curing complete including Excavation

the cost of&form

work but excluding

23 reinforcement for reinforced concrete work in:Slab (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be paid) Cum 169.00 6,177.00

1) R.C.C. slab Ground Floor

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

24 reinforcement for reinforced concrete work in:Slab (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be paid) Cum 15.00 6,216.00

2) R.C.C. slab First Floor

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in: Staircase (Design Mix or RMC can be use as directed by EIC/PMC. No Extra Rate can

1) Staircase Ground Floor

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in: Staircase (Design Mix or RMC can be use as directed by EIC/PMC. No Extra Rate can

2) Staircase First Floor

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in : Lintel (Design Mix or RMC can be use as directed by EIC/PMC. No Extra Rate can be

1) Lintel Ground Floor

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work in : Lintel (Design Mix or RMC can be use as directed by EIC/PMC. No Extra Rate can be

2) Lintel First Floor

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work: Chhajja (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

1) Chhajja Ground Floor

Providing and laying controlled cement concrete M-250 and curing complete including the cost of form work but excluding

reinforcement for reinforced concrete work: Chhajja (Design Mix or RMC can be use as directed by EIC/PMC.No Extra Rate can be

2) Chhajja First Floor

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement concrete work, using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to

Kms. having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work

including pumping of R.M.C. from transit mixer to site of laying in levels and pattern of bays as detail of architect and finished with

screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc., finishing and

31 reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve Cum 454.00 7,440.00

workability without impairing strength and durability as per direction of the Engineer in - charge. Without Fly Ash (Min cement level as

per latest IS 456 shall be maintained). The rate shall include cost of side shuttering with channels, rails, to form panels and groove

cutting etc. including filling the joint with glass strip/polysulphite complete to use. The rate shall also include the cost of reinforcement

approximate calculated at 5.14 kg/Smt. Rate for all lead & lift & as per directed by Engineer in - charge.

(Note: - Cement content considered in this item is @ 450 kg/cum.)

Item Description Unit Rate Amount

Providing and laying TMT Bar FE 500D reinforcement for R.C.C. work and bending, binding & placing in&position

Excavation completed upto any

floor any level as per I.S. Standard. complete.as directed by EIC.

(C) Masonry Work

Providing and laying Brick work using common burnt clay building bricks having crushing strength not less than 35 kg/Sq. cm. In

33 foundation and plinth in cement mortar 1:6 (1 cement : 6 fine sand) (B) Conventional. Up to Cum 90.00 3,981.21

1) Plinth level.

Providing and laying Brick work using common burnt clay building bricks having crushing strength not less than 35 kg/Sq. cm. In

34 Superstructure in cement mortar 1:6 (1 cement : 6 fine sand) (B) Conventional. Cum 668.00 4,253.46

2) Ground Floor.

Providing and laying Brick work using common burnt clay building bricks having crushing strength not less than 35 kg/Sq. cm. In

35 Superstructure in cement mortar 1:6 (1 cement : 6 fine sand) (B) Conventional. Cum 154.00 4,293.25

3) First Floor.

Providing and laying Brick work using common burnt clay building bricks having crushing strength not less than 35 kg/Sq. cm. In

36 Superstructure in cement mortar 1:6 (1 cement : 6 fine sand) (B) Conventional. Cum 10.00 4,333.04

4) Second Floor.

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in

(B) Conventional

(1) Ground floor

Providing & Fixing the Chikenmesh - 20 guage (Crimp Jali) of approved size applying between the RCC and masonry junction in proper

38 line, level and plumb with all material, labour, tools, tackles and equipment. Including providing and fixing the jali with nails, etc Sqm 1,949.00 285.00

complete as directed by the site-in-charge

(D) Plaster & Paint Work

Providing and laying 20 mm thick water proof cement plaster using water proofing powder 1 Kg / 1 bag of cement for all floors on brick

39 / concrete wall work using water proofing materials in C M 1: 4 (1 cement : 4 coasrse sand) including finishing with a flooting coat of Sqm 4,452.00 249.00

neat cement slurry etc complete for all floor.

Providing 15 mm. thick cement plaster in single coat on fair side of brick wall for interior plastering upto floor two level finished even

40 and smooth in [II] Cement mortar 1:4 (1 cement : 4 fine sand) For all levels, hights and leads of works. etc. complete as directed by EIC. Sqm 4,969.00 155.61

1) Ground Floor

Providing 15 mm. thick cement plaster in single coat on fair side of brick wall for interior plastering upto floor two level finished even

41 and smooth in [II] Cement mortar 1:4 (1 cement : 4 fine sand) For all levels, hights and leads of works. etc. complete as directed by EIC. Sqm 566.00 180.18

Providing 15 mm. thick cement plaster in single coat on fair side of brick wall for interior plastering upto floor two level finished even

42 and smooth in [II] Cement mortar 1:4 (1 cement : 4 fine sand) For all levels, hights and leads of works. etc. complete as directed by EIC. Sqm 33.00 203.34

3) Second Floor

Providing & laying 10 mm. thick cement plaster in single coat on fair side of brick concrete walls & ceilings for interior plastering upto

43 floor two level and finishing with smooth mala plaster. (i) Cement mortar 1:4 (1 cement : 4 sand) Sqm 1,328.00 114.66

1) Ground Floor

Providing & laying 10 mm. thick cement plaster in single coat on fair side of brick concrete walls & ceilings for interior plastering upto

44 floor two level and finishing with smooth mala plaster. (i) Cement mortar 1:4 (1 cement : 4 sand) Sqm 100.00 139.23

Item Description Unit Rate Amount

Excavation & Earthwork

Providing & laying 20 mm. thick Mala cement plaster on walls up to any height any lead and above ground level consisting of 12 mm.

thick backing coating of C.M. 1:3 (1 cement : 3 sand) and 8 mm. thick finishing coat in C.M. 1:1 (1 cement :1 sand) etc. complete.

Providing and applying 2mm thick Texture Plaster of Earthen Textures, Travertino Texture, Coral texture or equivalent make

incorporating fine filaments made of polymer and aggregating natural stone powder with making grooves on existing base coat of 20 mm

thick smooth mala plaster etc. Complete with two coat Exterior weather proof paint and one coat of primer in any shade As per drawings

and design supplied by architect and instruction given by authority and E.I.C. for all floor all height.

Providing 8 mm Luxture decorcem expose concerte or brick concerte coating and wall textured paint using base coat, tapping, durabond

47 expose RCC materials and finishing with decorsil two coat etc. complete. As per drawings and design supplied by architect and Sqm 439.00 1,582.48

instruction given by authority and E.I.C. for all floor all height.

Applying two coats of Birla or Asian acrylic lappy (putty) and two coats of primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand

48 prepared smooth. (Putty shall have low-VOC (Volatile Organic Compound) and Wall painting (two coats) with plastic emulsion paint of Sqm 6,997.00 118.63

approved brand and manufacture on wall surfaces to give an even shade including thoroughly brushing the surface free from mortar

droppings and other foreign matter and sand papered smooth.

Wall Painting (two coats) with weather proof extirior emulsion paint of approved brand and manufacture and of required shade on

49 exterior wall surface to give an even shade over and including a primery coat with alkaly resistance primer of approved brand after Sqm 4,388.00 113.40

thoughly brushing surface to remove all dirt and remains of loose powdered materials etc comp. for all height.

(E) Door & Window Work

Providing and fixing flush door both sides laminated and I.T.W. beading all around by using I.T.W. frame 120 m.m. x 80m.m.. shutter

fabricated from 35 mm thick solid core malemine faced three layered pre laminated flat pressed wood based exterior grade bonded

50 BWP/BWR synthetic resin having stamped IS 12823 grade I type II including three coats of lacquer polishing to exposed wooden Sqm 61.00 5,773.00

surfaces and Stainless steel decorative type designs fixtures / fastening 2Nos. Handles, 2Nos. Aldropes, towerbolt etc.including I.T.W.

triangular batten patti of size 30m.m.x30m.m.etc. as per architectural detailed drawing and as directed by engineer in charge..

Providing and fixing FRP FRAME size 100 x 50 mm & 28 mm thick FRP depress pannel shutter having extra reinfocement on sides and

edges in Gel coat finish. The core of the shutter & frame is to be filled up with injected fire retardant grade plyurethane foam done in situ

along with embedded wooden pices for stiffening & also for taking hinges and fixtures. The whole FRP frame and shutter is to be water

proof, weather proof, termite proof and resistance to mild acid/alkalis Rates are to be inclusive of S.S. hinges with necessary screws and

stainless steel fixtures and fastening with fastener & sleeve. Product should have 3 years perfomance guarantee & company have 9001-

2000 certificate. (For Toilet Purpose)

Providing and fixing All door partly glazed & partly pannelled door of approved colour Andised and standard extruded alluminium

frame 101.60 x 44.45 x 1.60mm @ 1.301 kg. with provided single door shutters having bottom rail 114.30 x 44.45 x 1.35 @ 1.19 Kg/

Rmt. Lock, Top & style 83.50 x 44.45 x 1.80 @ 1.50 kg ,Vartical rail 85.00 x 44.45 x 1.80 @ 1.301 Kg/Rmt and glazing clips 19.00 x

17.30 x 0.90 @ 0.124 Kg/Rmt with 5mm thick float glass,silicon gasket and 6mm Pre-lamineted board at bottom as per drawings 1-nos

of pivot/ Hinges 4 nos 125mm, D type 200, Alluminium handle 2 nos, lock of Apprvoed Quality 1 nos, Towarbolt 150mm 1 Nos, Floor

door stopper 1 Nos, including fixtures & Fastening etc. Complete.

Item Description Unit Rate Amount

Providing & fixing in position standard extruded Aluminium Partition with Colour anodizedExcavation

&frame of approved shade &

pivoted without shutter fabricated from alluminium standard section for outer frame size 101.60 x 44.45 x 1.60mm @ 1.301 kg. and

53 using Glasing Clips 19.00 x 17.30 x 0.90 @ 0.124 Kg/Rmt and providing rubber gasket around the glass allover including providing 6 Sqm 46.00 3,063.00

mm th. transparent float glass of copper/ gray tint (Structural Glass) fixed with transparent silicon gasket and in bottom panel 6mm thick

compact sheet bothside including all required materials labours and equipments as per detailed drwg. as directed.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS :

54 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment Nos. 24.00 2,815.00

with necessary accessories and screws etc. complete.

Providing and fixing window having extruded aluminum Colour anodized section frame main outer size 63.50 x 38.10 x 1.95 mm,@ Wt

1.094 Kg / Rmt, horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm @ wt.of 0.695 Kg/mt, vertical member of size

mm x 31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm @ wt.of

0.456Kg/mt, vertical member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with 5 mm thick transparent

bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as

per details etc complete for window.

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with colour

anodized alluminium frame for ventilation with 5 mm thick frosted glass as details etc complete for Ventilation

Providing and fixing rolling shutters of approved make made of 80 mm wide M.S. laths inter-locked together through their entire length

and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and

arragements for inside and outside locking with push-pull operation including the cost of hood cover and spring etc. complete.

(A) Shutters having width below 3.5 M.

Proving and fixing 12mm thk fixed toughned glass with required SS fitting complete in all respect. Note :- (i) Rate to include all

necessary supports & U channel at bottom and as per details.

(F) Structural Steel Work

Providing and fixing M.S. grill of required pattern for windows etc. with M.S.. flats at required spacing and frame alround square or

59 round headed bolts and nuts or by screws.including applying a priming coat of red lead paint and two coats of oil painting etc complete Kg 1,164.00 107.00

(A) Plain grill

Providing, supplying, fabricating and erecting in position the structural steel for colums, grill, gates, bars, truss, purlins, runners, cleats,

insert plate, base plate etc for all structural elements as per detail, made up from closed structural steel hollow sections (RHS/SHS

including rolled section) or angle or chanel with weather resistant of Tata Structural / sections or an approved equivalent as per details /

60 drawings/instructions including cutting, bending, jointing, connecting, welding and / bolting and / riveting and fabricating and erecting Kg 1,553.00 86.00

in position etc complete for all levels as directed. The rate to include all necessary fixtures, fastening including welding rods of standard

approvded quality etc for complete the job. The rate shall also include the two coats of synthetic enamel paint with priming coat &

necessary scaffolding etc. complete as directed

(G) Flooring Work

Providing and laying Bare Foot flooring tiles over 20 mm. average thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and laid

over and jointed with grey cement slurry including rubbing and polishing complete. 18 mm Thick Bare Foot Tiles

Providing and laying Granite stone slab flooring over 20 mm. average thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and

laid over and jointed with grey cement slurry including rubbing and polishing complete. 18 mm Thick

Providing and laying polished granite stone slab 18 mm thick in risers of steps, dedo and pllars laid on 10 mm thick cement mortar 1:3 (1

cement : 3 coarse sand) and jointed with gray cement slurry including rubbing & polishing etc. complete.

Item Description Unit Rate Amount

Providing & fixing Granite for Door Jamb, Sill and the like similar location of 18mm thick,Excavation

from 1050 to & Earthwork

2105mm in length and width

150mm /250mm in cement mortar 1:2 [1 white cement : 2 marble dust] with an admixture of pigment to match the marble shade

64 including fixing with copper pin 7.5cm long of 6mm diameters in cement mortar 1:2 (1 cement : 2 fine sand) including making rebate for Sqm 85.00 3,254.00

door shutter in Granite, edege polishing and moulding etc. completed as directed by EIC / Consultant.(Clear measurement will be taken

on sqmt basis for both Jamb)

Providing and fixing Granite sand which type platform including supplying and fixing granite stone 18 mm thick mirror polished 1st

quality Granite stones in top and side posiition and vertical strip at front over 25 mm thick polished kotah stone platform fixing in top

and sides and itermediates supports fixing with cement mortar and adhesivee and finishing including providing & cutting of kitchen sink

(as directed) 600 mm x 450 mm x 200 mm size stainless steel sink (as directed by engineer incharge) at required position etc complete.

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement

66 mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off Sqm 1,060.00 739.89

junctions and extending them upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1cement : 6-coarse sand)

or L.M. 1.1.5 (1-Lime putty :1.5 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete.

Providing and laying polished kota stone slab 25mm thick in risers of steps, skirting Dedo and pillars laid on 10mm thick cement mortar

68 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and Sqm 14.00 1,176.03

polishing etc. complete.

Providing and laying coloured glazed tiles of the size 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick

cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm nominal size) laid in

one layer and finished with a floating coat of neat cement. (B) 50mm thick.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than

0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4

71 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments Sqm 361.00 1,104.73

etc., complete.

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by

manufacturer), with water absorption less than 0.08 % and conforming to I.S 15622, of approved make, in all colours & shade, in

72 skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ Sqm 24.00 1,181.24

sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new

73 surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement Sqm 303.00 1,383.99

slurry including finised with flush pointing & cleaning the surface etc. complete for antiskit

Providing and laying IPS cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm nominal size) laid

in one layer and finished with a floating coat of neat cement. (B) 50mm thick.

Providing and laying chemical coating masterseal 550 El (BASF or equivalent) in existing swimming pool area with clening surface with

brush or other material as instruction, approved by architect engineer in charge.

Item Description Unit Rate Amount

Excavation & Earthwork

244 x 119 x 9 mm FINA approved vitrified tile in white or sky blue colour and lane marking as per FINA in dark blue or black Sqm 1,870.00 1,950.00

Fixing Specialized Tiles: Tile size 244 x 119 mm x 9 mm thickness (6mm spacer between tiles) of Orient Blue / New Blue / Dark Blue

Shade complete as per suggested by Architect. Following is the Laying procedure of tile in Olympic Size Swimming Pool: 1) Laying of

77 tiles by keeping spacers between two tiles with L111 Crete Filler Powder + L73 Crete Admix. Company suggest L111+L73 for vitrified Sqm 1,870.00 2,400.00

body tile. 2) After laying of tiles, will do pre-grouting with white cement and then epoxy grouting with SP100 latapoxy. 3) After epoxy

grouting, will clean swimming pool with mild acid. So total thickness after plaster with tile will be 13mm.

78 244 x 119 FINA approved Hand Grip tile on the top wall between pool & overflow channel Nos. 633.00 750.00

79 244 x 119 FINA approved anti skid tile on the top wall between pool & overflow channel Nos. 633.00 750.00

Fixing hand grip and anti skid tiles: Tile size 244 x 119mm (6mm spacer between tiles) Following is the Laying procedure of tile : 1)

Laying of tiles by keeping spacers between two tiles with L111 Crete Filler Powder + L73 Crete Admix. Company suggest L111+L73

for vitrified body tile. 2) After laying of tiles, will do pre-grouting with white cement and then epoxy grouting with SP100 latapoxy. 3)

After epoxy grouting, will clean swimming pool with mild acid.

(H) Miscellaneous Work

81 Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1 including neat cement finishing, watering etc. complete. Rmt 216.00 23.45

82 Providing and laying throttling or plaster and molding to RCC Chhajja. Rmt 216.00 41.25

Carring out plinth treatment to post construction /existing structure by spraying chemical solution for termite control treatment including

labour and material consistment with I.S.I specification. Using Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration

Weight one percent is recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1 % concrentration inclusive of one litre

chemical emulsion appication at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S

Providing and fixing Structural Glazing with using the 17 Micron anodised of approved colour alluminium section as transium, mullium

of size 63.5mm x 38.1mm x 2 mm with using 5 mm thick reflective structural glass and fixed with silicone sealant and spacer tap and at

corner sealed neoprene foam dust and Air sealed gasket mirred including scaffolding etc.complete with all necessary fitting and fixtures

for openable window as per Architectural drawing and as directed by Engineer-in-charge.

Providing and laying rough kota stone machine cut size 2' x 2'with spacer flooring over 20 mm (average) base of cement mortar 1:5 (1

85 cement : 5 coarse sand) or L.M. 1.1.5 including pointing with cement mortar 1:2 (1 cement : 2 stone dust) etc.complete. Sqm 58.00 544.03

Making holes upto any RCC members by diamond Core Cutting machine of HILTI or equivalent including disposing the debries.

Item Description Unit Rate Amount

Excavation & Earthwork

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular edge & 15 mm Thick Densified edges on

the Tile Periphery for Extra Strength The Light weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as

per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best thermal Insulation . The

Light weight calcium Silicate tile shall be of approved texture Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & Globe having

NRC value of 0.75 NRC or equivalent of size 595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot

dipped galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at

joints to get required length and size of 24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’

of size 24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to centre to

form agrid of 1200X600mm and secondary cross ’T’ of length 600mm and size 24x28mm made of 0.30 mm thick (Minimum) sheet to

be interlocked at middle of the 1200X600mm panel to form grid of size 600X600mm resting on periphery walls/partitions on a perimeter

wall angle pre-coated steel of size (24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm

centre to centre with 25mm long dry

Pro. And fixing single layer water proof gypsum board 12.5 mm thick sections using water proof board of size 1220 mm x 1830 mm x

8.0 mm suspended by GI suspender channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at

90 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter channel A of size 20 mm x 27 mm x Sqm 953.00 600.94

30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat, anchor fastener, scoch bolt connecting cleat,joining compound top coat

on ceiling incl.making necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed

Drilling hole of required diameter and depth` as directed for fixing of rebars,using hammer drill, cleaning the hole using mechanical air

91 flower, water etc,providing and fixing rebar in the drilled hole using RE 500 V4 or Equivalent approved make Cementetious chemical Each 86.00 631.00

grout and sealant with necessary scaffolding, staging, labour, tools and equipment etc. complete as directed by Engineer-in-charge.

(A) 8 mm dia bar (160 mm depth)

92 (B) 10 mm dia bar (200 mm depth) Each 86.00 906.00

93 (C) 12 mm dia bar (240 mm depth) Each 86.00 1,261.00

94 (D) 16 mm dia bar (320 mm depth) Each 86.00 2,166.00

95 (E) 20mm dia bar (400 mm depth) Each 86.00 4,212.00

96 (F) 25mm dia bar (500 mm depth) Each 86.00 8,659.00

97 (G) 32mm dia bar (640 mm depth) Each 86.00 15,981.00

Fabricating, supplying and fixing in position SS railing for staircase and Swimming Pool etc,. with brush finish and 304 grade as per

98 Indian Standrd and detailed drawing including grinding, cleaning and filling the welded spots with SS finish (Only Length will be paid Rmt 38.00 2,425.00

for payment heigth max.1.0 mt.). The Work to be executed as per consultant drawing .

Fabricating, supplying and fixing in position SS daso for staircase and balcony with brush finish and 304 grade as per Indian Standrd

99 and detailed drawing including grinding, cleaning and filling the welded spots with SS finish (Only Length will be paid for payment ). Rmt 37.00 1,365.00

The Work to be executed as per consultant drawing .

Item Description Unit Rate Amount

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thickExcavation

with grade&ofEarthwork

concrete M300 pnumatic

compressed / vibrated mechanically and as per approved design Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and level as per guidlines of IRC : SP 632018 etc. Complete.(Alcock,Vyara or equivalent

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 35cm length,30cm height and 15cm thick of

101 M250 grade concret as per approved design and including excavation for fixing in proper line and level,filling the joint with C:M 1:3 Rmt 428.00 358.06

(1cement:3fine sand) etc complete.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under

ground structures as directed by Engineer-in-Charge and consisting of :

(i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement :

3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course

(leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended

(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd

Using rough kota stone. (Horizontal)

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to

25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of

20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing

compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement

punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge :

Using rough Kota stone. (Vertical)

Providing, laying and fixing 200 mm wide PVC water stop of approved make and grade thickness in concrete work for water

104 tightstructures like retaining walls of pound water body and underground water tank including cleaning and placing in line level etc. Rmt 912.00 508.00

complete, as directed.

Supply of HDP (High Density PVC) Locker made out of 12mm & 18mm thick board, size 300w x 450ht x 400 dt mm with 18mm thick

106 Providing & Fixing AUTOGLOW Signages in Block / Small Letters of Specified Sizes Fire lift size: 4" X 12" Each 46.00 298.93

Providing and fixing cast iron steps of size 500 mm x 150 mm x 22.5 mm and painting with two coat, coats of anticorrosive paint etc.

108 Providing and Fixing C.I. Cover with Frame: 600mm X 850mm Each 9.00 3,840.18

109 Supplying and fixing, water level controller for the over head tanks of approved make complete, as directed Each 2.00 5,011.61

Item Description Unit Rate Amount

Excavation & Earthwork

Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to

wooden cleats with C.P. brass screws and washers complete.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including

adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken

bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineerin charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5

coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge to required slope and

treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper

curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS :

2645 and approved by Engineer-in charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4

coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass

fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making

pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two

weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge

:With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (Terrace)

(Only plan area should be measured)

Constructing Under Ground water tank with Providing and laying controlled cement concrete M250 mix for R.C.C. work including

reinforcement, boxing, centering, vibrating, , PVC water stopper, curing and mixed with approved water proofing cement compound or

"CEMWET" or "PIDICRETE LW" integral water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall be as

recommended by the manufacture of the water proofing material, concrete work for top, bottom slab & side pardi for underground water

112 tank item incl. Necessary excavation & refilling the available earth, 15 cm thk 1:2:4 for bedding of concrete, 20 mm thk. water proofing Litre 82,500.00 15.00

cement plaster in C.M. 1:3 with smooth finishing & Glazes tile Dedo, vata, watering etc. Comp. to all face of tank . including locking

arrangement outlet, inlet, overflow and washout outlet pipe arrangement as necessary & C.I. Cover 0.60 x 0.45 weight not less then 35 kg

with locking arrangement. etc. comp as per structural drawing Including Reinforcement TMT-FE 500D as directed by Engineer in-

Constructing RCC Overhead water tank with Providing and laying controlled cement concrete M250 mix for R.C.C. work including

reinforcement, boxing, centering, vibrating, , PVC water stopper, curing and mixed with approved water proofing cement compound or

"CEMWET" or "PIDICRETE LW" integral water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall be as

recommended by the manufacture of the water proofing material, concrete work for top, bottom slab & side pardi for Overhead water

tank item incl. 20 mm thk. water proofing cement plaster in C.M. 1:3 with smooth finishing & Glazes tile Dedo, vata, watering etc.

Comp. to all face of tank . including locking arrangement outlet, inlet, overflow and washout outlet pipe arrangement as necessary & C.I.

Cover 0.60 x 0.45 weight not less then 35 kg with locking arrangement. etc. comp as per structural drawing Including Reinforcement

TMT-FE500D As per drawings and design supplied by architect and instruction given by authority and E.I.C.

(J) Percolation Well

Item Description Unit Rate Amount

114 Boring and Sinking 30 cm. Diameter. Percolation well Excavation & Earthwork Rmt 184.00 760.00

115 Soak well around 3.0 m. dia. X 5.0 m. liquid depth including brick masonary for well Nos. 2.00 1,30,400.00

116 Brick masonry collection cum filtration tank around soak well Nos. 7.00 34,500.00

117 15 cm. diameter strainer pipes (Johnson make) having slot size 1.5 mm x 57 mm (72 slots in one line) in the casing pipe Rmt 81.00 1,830.00

Supplying, fitting, fixing and lowering 30 cm. diameter strainer pipe 1.2 m long (Johnson make) having slot size 1.5 mm x 57 mm (72

slots in one line)

119 Providing and lowering 15 cm size M.S. (3 m long) bail plug to the bore hole. Set 7.00 3,800.00

120 Supplying, lowering, fitting, fixing and joining with Strainer, 15 cm. diameter M.S. Pipe of minimum 5.40 mm wall thickness Rmt 78.00 1,175.00

121 Cement ceiling the saline zone as per logging report and as directed by the employer. Job 2.00 10,265.00

Supplying, washing and shrouding with approved gravel, the annular gap between the casing pipe and the remaining annular space to be

filled in with puddle clay (for which no measurement with be taken and paid for ).

123 Hire and labour charges for necessary tools and plants for conducting proper tests for percolation water, Nos. 2.00 14,945.00

(J) Plumbing Work

Supplying and fixing reinforced concrete heavy duty nonpressure pipes with collars for culverts including setting and joining the pipes in

124 C.M. 1:2 watering and laying (To level of slops of I.S. 458 / 1971 Class NP4 of following internal diameter. Rmt 380.00 344.64

(I) 300 mm dia.

Providing & Laying & Jointing glazed stoneware pipes incl. excavation up to 2.0 mt.,refilling, trasporting the pipe to work site,

unloading, lowering in trenches, laying and jointing the pipes in c.m. 1:1 incl. all jointing materials such as cement, sand, hemp, bitumen

125 as dire. testing the pipe line to a head of 1.5 mt. and hydraulic test as dire incl. watering trenches, spreading ,and carting away of surplus Rmt 99.00 344.64

earth within 100 mt.lead as dire. etc.comp

(A) 230 mm dia.

Providing & laying cement concrete 1:5:10 (1- Cement,5- fine sand,10 - graded stone aggregate 40mm Nominal size ) bedding for

128 stoneware pipes of following internal diameters with necessary formwork & curing complete. Rmt 380.00 550.00

Providing & laying cement concrete 1:5:10 (1- Cement,5- fine sand,10 - graded stone aggregate 40mm Nominal size ) bedding for

129 stoneware pipes of following internal diameters with necessary formwork & curing complete. Rmt 99.00 355.48

Providing & laying cement concrete 1:5:10 (1- Cement,5- fine sand,10 - graded stone aggregate 40mm Nominal size ) bedding for

130 stoneware pipes of following internal diameters with necessary formwork & curing complete. Rmt 200.00 211.59

Item Description Unit Rate Amount

Providing & laying cement concrete 1:5:10 (1- Cement,5- fine sand,10 - graded stone aggregate 40mm&Nominal

Excavation size ) bedding for

131 stoneware pipes of following internal diameters with necessary formwork & curing complete. Rmt 132.00 125.90

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain

and other end socketed with rubber ring, & fittings conforming to SI 14735-1999 of approved make for drainage system pipe line, pipe

132 shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 Rmt 141.00 822.99

mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain

and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe

133 shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 Rmt 132.00 826.88

mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 75 mm diameter with jali of the following nominal diameter of self

cleansing design with S.S. scread down or hinged grating including the cost of cutting and making good the walls.

Constructing brick masonry chamber for under ground C.I. Inspection chamber and bends with bricks having croshing strength not less

than 35 Kg. Cm2 in C.M. 1:5 C.I.cover with frame (Lightduty) 455mm x 610 mm intenal dimensions total weight of cover with frame to

be not less than 38 Kg. (Wt. of cover 23Kg.) and Wt.of frame 15Kg.) (R.C.C.top slab with 1:2:4 mix (1- cement:2 coarse sand:4-graded

stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15 mm thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete etc. complete.

(i) Inside dimensions 455 mm x 610 mm and up to 850 mm deep

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:3 (1Cement : 3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size

900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. /Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand)

(1) A type depth 0.90 Metre

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:3 (1Cement : 3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size

900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. /Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand)

(2) B type depth up to 1.50 Metre

Item Description Unit Rate Amount

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1cement :2-coarse sand : 4-graded stone aggregate

Excavation 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:3 (1Cement : 3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size

900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. /Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand)

(3) C type depth 2.25 Metre

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe , tap etc. complete. (A) White earthen

ware flat back or corner type size 430mm x 260mm x 350mm

Providing and fixing 15mm dia C.P. bib cock of approved make like jaquar or Essess or any other type and make specified by the

140 Architect. All pillar cocks, stop cock, angle cock etc to be Jaquar or EssEss make with quarter turn disc ceramic cartridge and chrome Each 42.00 750.00

Providing and fixing C.P. brass angle valve for basin mixer of approved quality conforming to IS:8931 of Approved make as approved

141 by engg. in charge all complete. Each 78.00 1,041.00

15 mm Nominal Bore Dia

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet Shower Arm.

(A) 100mm dia. Each

Provdg. & laying S.W. Gully trap with C.I. garting brick masonry chamber & water tight C.I. cover with frame of 300 mm x 300 mm

size (inside) with standard weight. sqare mouth trap size 150 x100 mm P Trap

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary fittings and connection etc.

complete on terrace.

P/F PVC . (span) nahni trap and all of the following nominal dia of self cleanising design with C.I.Screw down or hinged greeting

inclusive cost of cutting and making good the walls and floors for drain 75 mm dia. etc. comp.

Provding and fixing to wall, ceiling & floor in true line and level UPVC pipe Schedule- 40 of Prince , Supreme , astral , finolex or

equivalent make as approved by engg. incharge. pipe shall be fix on wall with the help of clamp at every twi meter center to center of

146 shall be concealed as directed in cluding neccesarry fitting etc. in cluding testing of pipe and jointd and fixing the same with Rmt 132.00 71.93

adhesive solvent , including cost of all materials of following nominal bore.

Provding and fixing to wall, ceiling & floor in true line and level UPVC pipe Schedule- 40 of Prince , Supreme , astral , finolex or

equivalent make as approved by engg. incharge. pipe shall be fix on wall with the help of clamp at every twi meter center to center of

147 shall be concealed as directed in cluding neccesarry fitting etc. in cluding testing of pipe and jointd and fixing the same with Rmt 99.00 90.93

adhesive solvent , including cost of all materials of following nominal bore.

Provding and fixing to wall, ceiling & floor in true line and level UPVC pipe Schedule- 40 of Prince , Supreme , astral , finolex or

equivalent make as approved by engg. incharge. pipe shall be fix on wall with the help of clamp at every twi meter center to center of

148 shall be concealed as directed in cluding neccesarry fitting etc. in cluding testing of pipe and jointd and fixing the same with Rmt 99.00 117.97

adhesive solvent , including cost of all materials of following nominal bore.

Item Description Unit Rate Amount

Provding and fixing to wall, ceiling & floor in true line and level UPVC pipe Schedule- Excavation

40 of Prince , &

Supreme , astral , finolex or

equivalent make as approved by engg. incharge. pipe shall be fix on wall with the help of clamp at every twi meter center to center of

149 shall be concealed as directed in cluding neccesarry fitting etc. in cluding testing of pipe and jointd and fixing the same with Rmt 99.00 146.65

adhesive solvent , including cost of all materials of following nominal bore.

Provding and fixing to wall, ceiling & floor in true line and level UPVC pipe Schedule- 40 of Prince , Supreme , astral , finolex or

equivalent make as approved by engg. incharge. pipe shall be fix on wall with the help of clamp at every twi meter center to center of

150 shall be concealed as directed in cluding neccesarry fitting etc. in cluding testing of pipe and jointd and fixing the same with Rmt 99.00 193.73

adhesive solvent , including cost of all materials of following nominal bore.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling

& testing of joints complete as per direction of Engineer in Charge.

Item Description Unit Rate Amount

Provding And fixing to wall ,ceiling and floor 10.00 kg. F/Sq.Cm working pressure polythelene Excavation & Earthwork

pipes of the following outside

158 diameter, low, density, complete with special flange compression type fittings, wall clips etc. making good wall ceiling and floor. Rmt 66.00 274.68

Provding And fixing to wall ,ceiling and floor 10.00 kg. F/Sq.Cm working pressure polythelene pipes of the following outside

159 diameter, low, density, complete with special flange compression type fittings, wall clips etc. making good wall ceiling and floor. Rmt 190.00 332.91

Providing & fixing Wall-mounted European Closet SuiteCera 'Clair' model No 2035 P-Trap (White/Light Coloured) with Dual Flush

Tank , PVC pan connector, seat & lid (heavy duty) including C.I. Brackets,C.P. Flush cock, C.P. brass hinges, All Internal fittings

complete with rubber buffers, C.P. nuts, bolts, ChaKi, etc making holes in walls & floors, & finishing for ready to use.The rate includes

160 Providing & fixing 15mm Angle Valve as per product detail with braided hose pipe as per product detail, jet spray as per product detail Each 23.00 5,688.00

including cutting and making good the wall where required.( Ewc wall hung-p :Cera. (white/light coloured) Classic no.2037 or

equivalent, Chair bracket : Cera no:2434 or equivalent brand make, rag bolts, Dual Flush Cistern : Cera ( white/light coloured) no:

or equivalent, Angle cock: Jacquar no 051 continental or equivalent, Braided hose: Jaquar-Allied-803B-CP)

HANDICAP TOILET

Providing and Fixing Handicap Toilet set including EWC, Cistern, Seat Cover, Fittings, Washbasin,, Hinged Rail, Grab Bar and Faucet

with Spatula Lever including Cast Iron chair backed and necessary bolts and nuts complete, including painting of fittings and brackets,

cutting and making good the walls and floors wherever required to the satisfaction of Engineer-In-Charge. Special Needs Toilet Set:

Jaquar - CNS-WHT-755SN + Cistern Set CNS-WHT-207, Wash Basin CNS-WHT-811 & Grab Bar 2 No. - WAC-WHT-BG0800 &

WAC-WHC-BR0600 - 2 nos.+ or Equivalent approved Make. Rates includes all lead & lift as directed by EIC.

Providing and fixing metropole flush valve (jaquar catlog No FLV-1089) (self closing spring loaded) at any floor, level and height.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and

163 making good the same but including fittings. Nos. 26.00 3,513.00

(A) Vitreous China: (ii) Flat Back washbasin 550mm x 400mm size. (i) In White Colour.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.

(B) 600mm x 20mm size.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts.

Providing and fixing screw down bib taps of following size.

166 (A) Brass screw down bib tap polished bright. Each 42.00 212.68

Supply,Installing, tesitng and commissioning concealed forged brass lever operated ball valve of full flow with forged brass ball

(Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum

167 working pressure of 16 kg/cm2 etc. including providing of connectors, flanges, nuts, bolts, gaskets, etc as per drawings, specification and Each 13.00 1,133.93

as directed by the EIC.

Supply,Installing, tesitng and commissioning concealed forged brass lever operated ball valve of full flow with forged brass ball

(Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum

168 working pressure of 16 kg/cm2 etc. including providing of connectors, flanges, nuts, bolts, gaskets, etc as per drawings, specification and Each 13.00 2,267.86

as directed by the EIC.

Item Description Unit Rate Amount

Supply,Installing, tesitng and commissioning concealed forged brass lever operated ball Excavation

valve of full & flow with forged brass ball

(Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum

169 working pressure of 16 kg/cm2 etc. including providing of connectors, flanges, nuts, bolts, gaskets, etc as per drawings, specification and Each 11.00 3,574.11

as directed by the EIC.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)

Constructing Bombay Pattern Type Catch Pit of size 0.60 x 0.60 depth up to 1 mt including excavation, B.B.C.C. (1:5:10), 23 cms thick

173 brick maso. wall in the prop. of CM (1:6) with 40 mm thick IPS flooring in the prop M15 at bottom and 15 mm thick cement plaster Nos. 13.00 3,125.00

inside the catch pit in the proportion of CM (1:3) with out jali etc. comp. as directed.

174 CatchPit Jali Fixing P/F FRC catch pit jali with frame 600mm x 600mm clear opening etc. comp.. As directed by engineer in charge. Nos. 13.00 1,383.93

Total Amount of Civil, Site Development & Plumbing Work

Total Amount of Civil, Site Development & Plumbing Work

Ahmedabad Municipal Corporation

Construction of Swimming Pool at T.P.-128, F.P.-493 in Vatva Ward, South Zone, Ahmedabad.

BOQ - Electrical, ELV & Heating Ventilation & Air - Conditioning Work

SR. No. Item No. Description of Work Unit Rate Amount

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected

concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories

and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered

with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary

Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

Wiring for the light points as above but with IP66 Switch board with IP 66 Box and 6 Amp / 16 amp

2 E-2 Switch. 250 Volt one 6 A IP66 switch located on IP 66 box board of Legrand cat. No. 673000 & 684638 2.00 Nos. 2,040.00

3 E-3 Primary light point controlled by one SP MCB ( Same as above item but controlling with SP MCB ) 2.00 Nos. 525.00

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected

concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with

4 E-4 primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / 135.00 Nos. 131.00

Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as

(a) with medium class Rigid PVC pipe and accessories

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both

are of .ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to

be erected concealed in / flushed on wall/ceiling ,complete with 6A Modular type switches and following

5 E-5 type of accessories erected on PVC / Metallic box, single mounting base frame covered with textured / 2.00 Nos. 562.00

metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle

holder or ceiling rose or H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories

6 E-6 Do as above but for Secondary light point controlled by same two way switch 2.00 Nos. 192.00

SR. No. Item No. Description of Work Unit Rate Amount

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in /

flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type

electronic fan regulator with separately mounted and accessories with earth continuity of following type

erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as

(a) with medium class Rigid PVC pipe and accessories

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box,

8 E-8 single mounting base frame covered with textured / metallic front plate modules erected on / in wall / 35.00 Nos. 255.00

ceiling with following type accessories

Do - As - Above but for 6 A x 5 pin 250 Volt switched socket outlet point at convenient location. ( Plug &

Switch can be together or at different location )

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on

surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box

10 E-10 covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following 20.00 Nos. 704.00

type of accessories.

[II] For 16A Plug with 2-2.5 sq.mm Cu. Wire

(a) with medium class Rigid PVC pipe and accessories

Wiring for the 250 volts single phase and neutral 16 amps switched socket outlet with 4.0 sq.mm

FRLS flexible copper conductor 1100 volts grade wires of approved make with concealed or surface

11 E-11 mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 16 amps 5 pin switch 12.00 Nos. 829.00

socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures

and the outlet box with 2.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

Wiring for the UPS / Comp. / Raw Power outlet with 2 nos. of 250 volts single phase and neutral 16 amps

switched socket outlet with 2.5 sq.mm x 3 core FRLS flexible copper conductor 1100 volts grade

wires of approved make in concealed or surface mounted Prelaid 25 mm dia medium gauge PVC

Conduit / Race ways including providing and fixing of 2 no's of 16 amps 5 pin switch socket outlet of

approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet

box. ( Maximum 3 nos. of Plugs can be looped in 1 Circuit )

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed

Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness

14 E-14 Supply and laying of 32 mm rigid PVC pipe of 1.6-1.8 mm thickness 350.00 Rmt 52.00

15 E-15 Supply and laying of 40 mm rigid PVC pipe of 1.6-1.8 mm thickness 200.00 Rmt 64.00

SR. No. Item No. Description of Work Unit Rate Amount

MAINS : ( not for Point wiring )

Supplying and Laying of mains with Cu. PVC insulated flexible wire with ISI and FIA approval for 650 V/

1100 V with earth wires of Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth

wires with Suitable dia rigid PVC Pipe of Heavy Gauge ( Scope Also includes Supply of pipe. )

Supplying and Laying of 4 nos. of 10 sq mm Cu. FRLS flexible wires with 2 nos 4 sqmm Cu. FRLS

flexible wireswith 40 mm dia Pipe

Supplying and Laying of 2 nos. of 6 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS

flexible wires with 40 mm dia Pipe

Supplying and Laying of 2 nos. of 4 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS

flexible wires with 25 mm dia Pipe

Supplying and Laying of 2 nos. of 2.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS

flexible wires with 25 mm dia Pipe

Supplying and Laying of 2 nos. of 1.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS

flexible wires with 25 mm dia Pipe

Distribution Board

Supply, Assembling, grouting, leveling Connecting & testing D.B of IP 54 of specified make.

Distribution Board-VTPN

Supply, Erecting, testing and commissioning of only VTPN D.B. with space for FPMCCB / FPMCB as

incoming and 4 TPMCB / SPMCB as outgoing per phase (i.e. 4 way VTPN D.B.) of Legrand Make Cat.

Distribution Board-TPN

Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming

and space for DPELMCB and 4 SPMCB as outgoing per phase (i.e. 8 way per phase D.B.) of Hensel Make

Distribution Board-SPN

23 E-23 Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming 2.00 Nos. 3,860.00

and 8 SPMCB as outgoing per phase (i.e. 12 way D.B.) of Hensel Make KV9112M

Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming

and 4 SPMCB as outgoing per phase (i.e. 8 way D.B.) of Hensel Make KV7109M

All MCB's, ELMCB's, ELCB's should be of 10 KA only

25 E-25 providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having breaking capacity 8.00 Nos. 268.00

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

SR. No. Item No. Description of Work Unit Rate Amount

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking

32 E-32 capacity & confirms to IS :8828 in existing box having following capacity 5.00 Nos. 582.00

(a) 6 to 32 Amp. Cat.III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking

33 E-33 capacity & confirms to IS :8828 in existing box having following capacity 5.00 Nos. 641.00

(b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having following capacity

6 to 32A FP MCB

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. .

ICS= 100% of ICU only.

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate

battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised

permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure &

transparent cover erected as required with necessary connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction Cat III

(B) 2 pole 250V 32 Amp.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction Cat III

(D) 4 pole 440V 40 Amp.

41 E-41 SITC of IP65 Polycarbonate enclosure for DP MCB 2.00 Nos. 1,882.00

42 E-42 SITC of IP65 Polycarbonate enclosure for FP MCB 2.00 Nos. 1,995.00

Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the

run and backfilling the same and making the surface proper. Providing and erecting iron clad cable route

marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation

as directed by Engineer in charge. The width shall be as per requirement

SR. No. Item No. Description of Work Unit Rate Amount

Covering of cable with second class bricks laid cover the cable crosswise & also on both sides with covering

of 7. 5 Cms. layer of sand above & below cable (cable shall be laid in 0.9mtr.deep & 0.4 Mtr.wide trench).

44 E-44 Where there are more than one cable in the trench on either side of the cable, 5 Cms. over lapping of bricks 200.00 Rmt 139.00

shall be provided.

Construction of brick masonry pulling chamber 600 mm x 600 mm inside clear size and depth up to

meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM

proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum

45 E-45 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame 3.00 Nos. 10,423.00

and 600 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling &

clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of

the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 750 mm x 750 mm inside clear size and depth up to

meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM

proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum

46 E-46 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame 3.00 Nos. 13,138.00

and 750 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling &

clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of

the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 1000 mm x 1000 mm inside clear size and depth up to

meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM

proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum

47 E-47 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame 12.00 Nos. 16,746.00

and 900 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling &

clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of

the Engineer In charge complete in all respect.

Fabricating the box type items made from M.S. Sheet with A.I. supports, wings, doors, handles other

48 E-48 hardware materials as per requirement design with finishing by three tank powder coating processed inside 500.00 Kg 179.00

and outside painted, erected as directed including minor civil work.

Supply, Installation, Testing, Laying, Commissioning of following 1100 volt grade XLPE insulated PVC

sheathed aluminum / Copper conductor armored cables as per (IS:7098)(I)-88 ISI marked & specification in

trenches, cable trays, ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing

bolts, connecting testing and commissioning with identification tags at every 10 mtr. & Both ends. with All

the fixing accessories, excavation Back filling & Cable protection with Bricks as per the drawing ( If

70 sq.mm x 3.5 c Al. XLPE Arm. Cable

50 E-50 50 sq.mm x 3.5 c Al. XLPE Arm. Cable 50.00 Meter 282.00

SR. No. Item No. Description of Work Unit Rate Amount

51 E-51 25 sq.mm x 4 c Al. XLPE Arm. Cable 80.00 Meter 189.00

52 E-52 16 sq.mm x 4 c Al. XLPE Arm. Cable 500.00 Meter 152.00

53 E-53 10 sq.mm x 4 c Al. XLPE Arm. Cable 200.00 Meter 139.00

54 E-54 6 sq.mm x 4 c Cu. XLPE Arm. Cable 100.00 Meter 505.00

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV.

To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following

55 E-55 size cable. 50.00 Meter 392.00

6 sq.mm x 3 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV.

To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following

56 E-56 size cable. 80.00 Meter 282.00

4 sq.mm x 3 c cu. XLPE Arm. Cable

57 E-57 Supply & Laying of 1.5 sq mm x 3 core round flexible wire in prelaid pipe / Raceway. 50.00 Meter 46.00

58 E-58 Supply & Laying of 2.5 sq mm x 3 core round flexible wires in prelaid pipe / Raceway. 75.00 Meter 77.00

59 E-59 Supply & Laying of 4 sq mm x 4 core round flexible wires in prelaid pipe / Raceway. 30.00 Meter 175.00

Cable Termination

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

60 E-60 armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, 4.00 Nos. 197.00

double compression type Brass glands with earthing.

70 sq.mm x 3.5c Al. XLPE Arm. Cable

61 E-61 50 sq.mm x 3.5c Al. XLPE Arm. Cable 2.00 Nos. 150.00

62 E-62 25 sq.mm x 4 c Al. XLPE Arm. Cable 2.00 Nos. 111.00

63 E-63 16 sq.mm x 4 c Al. XLPE Arm. Cable 44.00 Nos. 107.00

64 E-64 10 sq.mm x 4 c Al. XLPE Arm. Cable 10.00 Nos. 90.00

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs,

65 E-65 double compression type Brass glands with earthing. 6.00 Nos. 62.00

6 sq.mm x 4 c Cu. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs,

66 E-66 double compression type Brass glands with earthing. 4.00 Nos. 51.00

6 sq.mm x 3 c Al. XLPE Arm. Cable

SR. No. Item No. Description of Work Unit Rate Amount

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs,

67 E-67 double compression type Brass glands with earthing. 6.00 Nos. 51.00

4 sq.mm x 3 c Al. XLPE Arm. Cable

SITC of Round Flexible wire end termination of the following insulated PVC sheathed copper conductor

Wires of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, IP66 / 67 -

3 mm thick Thermoplastic long entry glands of Hensel / Spelsberg with Strain relief and Lock nut.

1.5 / 2.5 Sq. mm x 3 / 4 core round flexble wire or Similar dia wire

69 E-69 4 / 6 Sq. mm x 3 / 4 core round flexble wire or Similar dia wire 4.00 Nos. 51.00

MV Switchgear & Power Panels

Supply, Unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, &

Commissioning main L.T. panel board, fabricated from M.S. sheet & folded channel totally enclosed

cubical type compartmentalized. Scope Covers Unloading at Site, Store in Weather Proof Condition, Shift to

the Location Basement / GF / FF, Grouting, Installation, Testing & Commissioning complete in all respect

& As per the instruction of Architect / Consultant / Engineer Incharge. Scope also covers Co ordination with

Panel Manufacturer.

Design, fabrication, assembling, supply, installation , testing of Panels for 415 V, 3 phase, 50 Hz, 4 wire

power supply system.

Panels shall be fabricated out of 2 mm thick CRCA sheet steel in cubical formation, compartmentalized in

Form 4b Construction, floor mounted, free standing and shall be dust and vermin proof. 3 mm thick cable

gland plate, shall be provided both at the top and the bottom of the panel.

All large panels shall be provided with lifting hooks. Distribution panels shall be fabricated in accordance

with the specifications.

Note : Panel vendor has to provide Surge Protection at every stage of the Distribution.

1) Supporting rigid steel framework.

2) Cubicle type, 14 gauge CRCA sheet steel enclosed.

3) Complete with interconnections and distribution bus bars.

4) Proper bonding to earth.

5) Painting/lettering on Breakers and distribution boards, the location they serve, providing on each panel its circuit diagram.

6) Providing cable clamps / supports within distribution boards cable alley.

7) TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link.

8) All MCB’s shall be of minimum 10 KA breaking capacity.

9) The breaking capacity of MCCB’s are mentioned panel wise.

10) All motor feeders MCCBs shall be of motor duty.

11) Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5.

SR. No. Item No. Description of Work Unit Rate Amount

12) Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993.

a) IP 52 for indoor panels.

b) IP 54 for kitchen and laundry panels.

c) IP 55 for outdoor panels.

13) All MCCB’s shall be provided with operating mechanism for door interlock & with the roraty handle.

14) Current density of aluminium shall be 1 sq mm for 0.8 amps for rated current of bus bars and current

density of copper shall be 1 sq.mm for 1 amps for rated current of bus bars.

15) Tinned copper earth bus as specified in the BOQ / SLD shall be provided through out the length of each

16) All measuring instruments (Meters) shall be of digital electronic with LED of approved make and

compatible with BAS.

17) All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.

18) All panels shall have provision of the following:

a) IP 55 for outdoor panels.

b) Pad locking of MCCB’s handles in “OFF” Position.

19) Additional set of C.T.s, potential free contacts, connectors, contactors with wiring etc are to be provided

for BAS including space required for various transducers in Main Switch Board sections. Only transducers

shall be supplied by BAS contractor.

20) All the C.T.s should be auto short link type.

21) All the MCCB's should be with rotary handle.

22) All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and

inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type

D characteristic.

23) All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single

tier formation.

24) All PTs / control transformer shall be provided with centre tap earth secondary.

25) If Any descripancy found in SLD & BOQ, it should be brought in the notice of the Client / Consultant,

Client / Consultant's decision will be final in case of any descripancy.

26) G.A. Drawing should be checked & Finalised by consultant before fabrication.

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity

ICU of 35 KA. at 415 V. having Normal current rating 200A.with variable Thermal & magnetic release

70 E-70 suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete 2.00 Nos. 16,061.00

erected in existing 16 G.M.S.housing

ICS=100% of ICU only Cat III

SR. No. Item No. Description of Work Unit Rate Amount

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed thermal & magnetic

71 E-71 release suitable to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & 1.00 Nos. 6,112.00

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Providing and erecting busbar chamber confirming to IS-375 fabricated from 16 G.M.S. sheet, dust &

vermin proof having hinged door with rubber gasket and necessary busbar supports with COPPER busbar

having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped

72 E-72 with colour insulation tape for phase sequence, three phase & neutral each suitable for following current 5.00 Rmt 4,378.00

capacity with necessary painting mounted on wall or pedestal frame of required size with necessary

(A) Suitable for 63/100 Amp. capacity

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four

equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section

area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators, main cable socket to each busbar,erected in existing

cubical panel with necessary connections.

(E) Suitable for 200 Amp. capacity

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal

Nos. of electrolyte bus having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section

area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators, main cable socket to each bar, erected in existing cubical

panel with necessary connections.

(A) Suitable for 100 Amp. Capacity

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover, complete erected

with necessary connections.

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA burden erected

in existing CRCA box duly secured with insulating materials connected to the meter

Supplying and erecting approved make panel mounting type Digital Voltmeter having 3 digits LED display,

77 E-77 0 to 750 AC Volts range erected on existing panel board with all connection, wiring etc .with 4.00 Each 1,263.00

manufacturers calibration certificate.

Supplying and erecting approved make panel mounting type Digital Ammeter having 3 digits LED

78 E-78 display, external CT operated, calibrated for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on 4.00 Each 1,543.00

existing panel board with all connection, wiring etc .with manufacturers calibration certificate.

Providing and erecting Approved make Earth fault Relay suitable to mount with inter connection suitable to

following size of moulded case circuit breaker having CT ratio & MCCB rating as following along with

shunt trip 220V AC. with all internal connections & complete erected in existing M.S.housing..

SR. No. Item No. Description of Work Unit Rate Amount

Providing and erecting multifunctional meter suitable for application of Power monitoring and showing

measurement of following Voltage, Frequency, Apparent energy, Apparent power, Active and reactive

energy, Active and reactive power, Average voltage Vavg, Peak demand power PM, QM, SM, Demand

power P, Q, S, Apparent power S, S1, S2, S3, Unbalance current, Power factor and displacement PF (signed,

four quadrant), Calculated neutral current, Active, reactive, apparent energy (signed, four quadrant), Active

power P, P1, P2, P3, Voltage U21, U32, U13, V1, V2, V3, Phase currents, Average current Iag, Peak

demand currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3, [Us] rated supply voltage

40...300 V AC 45...65 Hz, 40...300 V DC, Network frequency 50 Hz, Type of network 3P, Display type

segments LED, Display colour Red, Messages display capacity 3 fields of 4 characters, Display digits

digit(s) - 14.2 mm in height

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical

panel board necessary IP-42 and above protection as per approval from engineer incharge made from

SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions

with necessary accesories , supporting angles/ flats channel including cutting, bending, drilling, welding,

riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-

82 E-82 aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & 8.00 Sqm 14,755.00

earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with

following approved manufacturers with following size.

(B) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory

(i) with 350mm depth

83 E-83 (ii) with 550 mm. Depth 5.00 Sqm 19,196.00

84 E-84 (iii)with 750 mm. Depth 8.00 Sqm 33,230.00

SR. No. Item No. Description of Work Unit Rate Amount

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical

panel board necessary IP-42 and above protection as per approval from engineer incharge made from

SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions

with necessary accesories , supporting angles/ flats channel including cutting, bending, drilling, welding,

riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus &

earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with

following approved manufacturers with following size.

(C) The standard companies switch gear shall be used and only manufacturers as per IEC 61439 for

beneficial use.

(iii)with 750 mm. Depth

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.9, THD < 15%, CCT 3000 K to 6500K,

86 E-86 Luminaire efficacy> 85 lumens/watt ,LED LED driver efficiency > 85 % ( fitting required LM-79 & LM-80 18.00 Nos. 370.00

Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet, Cat-III

SR. No. Item No. Description of Work Unit Rate Amount

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.9, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED LED driver efficiency > 85 % ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet, Cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.9,

THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting

clips complete.IP20

(i) 5-9 watts,Surge-2 KV

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.9,

THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting

clips complete.IP20

(iii) 16-20 watts, Surge-2 KV

SR. No. Item No. Description of Work Unit Rate Amount

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

90 E-90 Luminaire efficacy> 85 lumens/watt , 5.00 Nos. 1,777.00

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(B) LED Panel Light with provision for Plane front frame with translucent cover fixed to housing

(vi) 36 watts, 24" x 24", Surge- 2KV

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

91 E-91 ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 22.00 Nos. 4,948.00

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

over-voltage protection.

(ii) above 48 to 60 Watts

Providing and erecting PVC body surface or pendent mounting LED Bulk type 9 watt Lighting Fitting with

electronic driver. And lumen output from luminaire 720lm , input voltage range 90-300VAC , 50Hz cool

white(3000 to 6500k), inbuilt driver, -20degC to +60degC working temperature, AL frame with Beam Angle

SR. No. Item No. Description of Work Unit Rate Amount

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

93 E-93 ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 2.00 Nos. 5,917.00

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

over-voltage protection.

(iii) Above 60 to 90 watts

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

94 E-94 ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 2.00 Nos. 6,501.00

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

(iv) above 90 to 120 watts

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

95 E-95 ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 2.00 Nos. 8,370.00

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

(v) above 120 to 160 watts

SR. No. Item No. Description of Work Unit Rate Amount

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

96 E-96 ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 46.00 Nos. 10,711.00

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

(vii)above 200 to 250 watts

97 E-97 Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM 2.00 Nos. 1,687.00

with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring

mounted low noise operation suitable for medium duty having following dia size and maximum speed in

[A] 305 mm dia 900 RPM

99 E-99 Providing suitable M.S. louver shutter of the Exhaust fan. 20.00 Nos. 365.00

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser

100 E-100 volt A.C.50 Hz. 1200 mm sweep complete having 4 blades Aluminium body and blade sets having 32.00 Nos. 2,335.00

ornamental design shanks, canopy erected with earthing [ Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted

101 E-101 for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing. 32.00 Rmt 107.00

SR. No. Item No. Description of Work Unit Rate Amount

Supply of approved make FRP Pole having following specifications: FRP Light Pole made by CNC

filament winding machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass

content. The pole should be in one piece and tapered round in shape, having smooth finish and should be

totally free from corrosion as well as non conductive & shock proof Pole should be provided with FRP

Anchor Base and it should be heavy duty, or MS Material duly painted with Epoxy paint. Pole should be

flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying suitable primer system that ensures proper

adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not

exceed more than 10% of the length of pole for the given load“ Pole should be generally made as per the

dimensional data, performance criteria and some interchangeability features of poles as per standard ANSI

C 136.20 latest version or ASTM D 4923/01 including cable termination box with necessary accessories .

The size of pole and type of installation with foundation as per manufacturer details and site requirement are

(2) Suitable for base plate mounting Double arm Bracket.

[C] Overall length of 6 Mtr. Average Thickness: 8mm.

Top/ Bottom OD Dia A/F 114/174 mm ± 2mm approx. approx. Weight of Pole 38 kg approx. (Without

Base) Anchor Base (Size 300X300 & 18mm th.)

Supply of approved make FRP Pole having following specifications: FRP Light Pole made by CNC

filament winding machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass

content. The pole should be in one piece and tapered round in shape, having smooth finish and should be

totally free from corrosion as well as non conductive & shock proof Pole should be provided with FRP

Anchor Base and it should be heavy duty, or MS Material duly painted with Epoxy paint. Pole should be

flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying suitable primer system that ensures proper

adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not

exceed more than 10% of the length of pole for the given load“ Pole should be generally made as per the

dimensional data, performance criteria and some interchangeability features of poles as per standard ANSI

C 136.20 latest version or ASTM D 4923/01 including cable termination box with necessary accessories .

The size of pole and type of installation with foundation as per manufacturer details and site requirement are

(2) Suitable for base plate mounting Double arm Bracket.

[G] Overall length of 8 Mtr. Average Thickness: 8mm, Top/ Bottom OD Dia A/F114/195 mm ± 2mm

approx. approx. Weight of Pole 54 kg approx. (Without Base) Anchor Base (Size 350X350 & 20mm th.)

Providing Aluminium arm bracket of having 2 sets of suitable SS304 hardware for fixing the brackets &

104 E-104 spread of 1.2 Mtr (Suitable for 89 to 114 mm pole top dia) 18.00 Nos. 2,212.00

(A) Single arm bracket

SR. No. Item No. Description of Work Unit Rate Amount

105 E-105 (B) Double arm bracket 4.00 Nos. 3,416.00

Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of

M.S. angles,square,round, flats, bars, channels, sections complete with cutting, welding, grinding &

finishing duly painted with one coat of red oxide with erection on site as per direction of engineer in charge

with necessary grouting, cementing, plastering & finishing complete.

Providing cement concrete.for foundation or for concrete filling in 1:2:4 ratio with 20 to 25 mm stone metal

duly plastered with necessary curing for pole muffing or any other purpose.

108 E-108 TMT Bar for Pole Foundation 150.00 Kg 75.46

Supplying & erecting funnel type earthing having earth plate of following size burred in specifically

prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt,

20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover

109 E-109 complete as per para 7.3 of IS 3043 with necessary length of double Galvanised Iron / copper earth wire No 2.00 Nos. 7,797.00

6 SWG bolted with lug to the plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to

the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to IS (As

per drawing) with following specification

60 x 60x 0.315 cms. Copper earth Plate

110 E-110 45 x 45 x 0.35 cms. C.I. earth plate 2.00 Nos. 2,543.00

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications.

For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant &

Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other

than normal soil i.e. Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg.

Earth wire/strips :

Supply and laying cu. earthing strips for interconnecting the earthing stations, panels, DB's etc. in built up

trenches, on walls/ceiling, buried in ground generally as specified and shown on drawings complete with :

fixing accessories

Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes.

Providing and erecting HOT deep Galvanized strip iron wire 8 to 16 S.W.G.

115 E-115 No.8 gauge bare cu. earth wire 25.00 Kg 815.00

116 E-116 Earth Link : 40mm x 6 mm earth link fixed by necessary screws on wall. 2.00 Meter 370.00

SR. No. Item No. Description of Work Unit Rate Amount

SITC of Water Tight Junction Box With necessary clamp for mounting of the J.B. ( All the cable / wire

117 E-117 connections to the JB shall be with the Water tight Glands only ) 14.00 Nos. 2,940.00

Telephone Outlet Point

SITC OF PowerCat 6 DataGate Jack, 568A/B - Yellow with Dust Cover / Blank/ One Telephone Point to be

118 E-118 done with Cat -6 Information outlet Socket, Back Box, Face Plate for all telephone point. Average Length to 8.00 Nos. 159.00

be considered as 50 Meter. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost.

Years of Certification is required. Test reports of Level-4 Scanners only.

SITC OF DG+ Jack (Diecast)Cat6A 568A/B, Shtd- Black (Information Outlet for Data) with Faceplate,

back box CAT-6A standards. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost.

20 Years of Certification is required. Test Reports of Level-4 Fluke Scanners Only.

SITC of Jack Panel, fully loaded with 24 nos. UTP ports for PCB based IO Jacks (RJ45, TIA-568C

Category-6, Installation and Termination of all 24 nos. Catergory-6 UTP , unloaded with individually

120 E-120 replaceable 24 nos. Category-6 I/O Jacks complying with TIA-568.C.2, as per given jack specification Shall 1.00 Nos. 4,357.00

be suitable for loading unshielded & shielded jacks for different category systems (CAT 6 & CAT 6A)

Supply and laying of PowerCat 6A U/FTP CM 4 Pair Cable, LSZH Sheath - Violet of specified make to be

done in prelaid PVC pipe of 25 mm dia / raceway of specified make, but without the cost of raceway or

121 E-121 pipe ( the wire is to be drawn from HUB \ Switch of respective area to outlet point ) with the cost of the 500.00 Meter 190.00

crimping with material of make Legrand / Molex/ Systimax / Panduit / Siemon

Fire Detection System

Supply, Installation, Testing And Commissioning of UL864, 10th Edition Microprocessor based 1 loop,

True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 50 characters LCD

display, 2000 event plus 500 alarm log history events, QWERTY keypad for programming. The panel

should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each

loop shall have a capacity of minimum 50 analog addressable devices. The panel shall work in degrade

mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels,

122 E-122 flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries 1.00 Nos. 35,000.00

sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be compatible with

Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation

Messages on same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of

supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU

shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having

minimum 5 Telephones in conference in multiple FFT Risers.

SR. No. Item No. Description of Work Unit Rate Amount

Supply, Installation, Testing And Commissioning of UL Listed Graphics User Interface for Monitoring &

Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network

software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically

representing each facility being monitored with floor plans and icons depicting the actual locations of the

various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any

123 E-123 detector. The software shall be capable of monitoring 100 Nodes with 100 Mbps Transmission rate on Fibre 1.00 Nos. 35,000.00

Optics Network and 12 Mbps Transmission on cable and 1,00,000 network points. The software shall be

capable to Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main

control room using voice signals over Fire Network along with the Fire detection signal. The Graphic

workstation shall act as an independent node communicating on the peer to peer network and shall not be

dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI.

Supply, Installation, Testing And Commissioning of Automatic printer capable for interface with NCS and

provided with RS 232/RS 485 protocol port. It shall be standard cartage with 80 characters per line as per

all requirements of technical specifications & contracts works.

Supply, Installation, Testing And Commissioning of UL268, 7th Edition Addressable Multi-criteria Photo-

Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device

shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric

signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to

125 E-125 distinguish between a fire condition and a false alarm condition by examining the characteristics of the 30.00 Nos. 5,344.00

thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive

phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user

friendly rotary decimal switches.

Supply, Installation, Testing And Commissioning of UL listed Addressable Manual Call Point (Pull down /

Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on

activation to monitor the heath status of the device.

Supply, Installation, Testing And Commissioning of UL Listed Sounder cum Strobe rated at 80 dBA @ 3m

127 E-127 for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed 1.00 Nos. 7,061.00

Supply, Installation, Testing And Commissioning of Addressable Control Module for Sounders / Strobes /

Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The

device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath

status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be

supplied with mounting plate from OEM for ease of installation & maintenance.

SR. No. Item No. Description of Work Unit Rate Amount

Supply, Installation, Testing And Commissioning of UL Listed Isolator Module for Isolating short / dewired

/ loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that

case needs to be considered with each detector & module. The device shall have an LED which shall blink

in normal state & get steady on activation to monitor the heath status of the device. Module shall be

supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, installation, testing & Commissioning of Battery pack suitable for back up of 4 hours with charger

130 E-130 in case of Alarm condition. 1.00 Nos. 36,316.00

Supply, installation, testing & Commissioning of response indicator

Supply, installation, testing & Commissioning Fire Exit Signage boards with 3hrs battery backup

Supply & laying of 2 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable

Supply & laying of 4 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable

Supply, Installation, Testing & Commissioning of Network TDN IR Mini Dome Camera, 1/2.9" CMOS,

MP @ 25fps, Triple stream, Min. Illumination required 0.25 lux @ color, WDR 120dB, Min. Pixels 2560 x

1920, Shutter Speed 1/30000 - 1/5; Adavance Video Compression technology such as H.265 / H.264 /

MJPEG, 3mm~8mm, MFZ lens, HLC, 3DNR, Minimum Edge Intelligence Video Analytics: Motion

Detection, Camera Tampering, Intrusion/Object enter area; 4 nos Privacy Mask, Smart IR with upto 30m IR

distance, AES-128/256, PCI Data Security Standard compliance, 128GB SD card support, DC12V, PoE

(IEEE 802.3af) (Class 2), IP 66, IK10, Having Operating temp range : –10°C to 50° C. Certifications:

ONVIF Profile S, G compliant, UL, CE/EN, FCC Part 15 & RoHS compliant along with mounting brackets

suitable for Cieling / Wall mounting & required accesories as per site requirement.

SR. No. Item No. Description of Work Unit Rate Amount

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN IR Bullet Camera, 1/2.8" CMOS,

5 MP @ 25fps, Triple stream, Min. Illumination required 0.05 lux @ F1.4 (color), WDR>120dB, Min.

Pixels 2560 x 1920, Shutter Speed 1/30000 - 1/30; Adavance Video Compression technology such as H.265

HEVC / H.264 / MJPEG, Smart Codec, 2.7-13.5 mm 5X motorized focus & zoom lens, P-IRIS, HLC,

3DNR, Minimum Edge Intelligence Video Analytics: Motion Detection, Video Tampering, Intrusion,

Loiter, Line crossing, Unattended object, Missing object, Face detection; 5 nos Privacy Mask, 4 IR LEDs

Smart IR with upto 60m IR distance, Stream encryption, AES-128/256, PCI Data Security Standard

compliance, FIPS Chipset Built-In, 256GB SD card support with SD card encryption, Dual channel Audio

G.711a / G.711 Mu / G.726, Alarm: 2 In/ 1out, In-built Heater; PoE+ (802.3 at) and 12V DC/24V AV; IP

/ IP 67 / NEMA 4X, IK10, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S,

G compliant, UL, CE (EN 50130-4 & EN 55032) , FCC Part 15 & RoHS compliant along with mounting

Brackets suitable for Pole / Wall mounting & required accesories.

SITC of 32 Channel NVR having features smart H.265+/H.265/ Smart H.264/H2.64/MJPEG, Max

137 E-137 Mbps incoming Bandingwidth, support min 2 SATA HDDs Slot - each slot supporting min 8TB, Up to 12 1.00 Nos. 64,975.00

MO Resolution for Preview and Playback and with 8 TB Survellance Hard Disk

Supply, Installation, testing and commissioning of Intel Core i5 12C Processor 25M Cache, up to 4.90 GHz

138 E-138 / 16GB DDR5 / 512 SSD / Win 10 Pro Operating System / No Monitor / DVD RW / 3 Yrs NBD / PS 500W/ 1.00 Nos. 75,900.00

NVIDIA T600 4 GB GDDR6 Workstation Graphics Card including 4 mDP to DP adapters

SITC of 32 Inch 500 NTS Brightness professional Display with Direct-Type LED, Viewing Angle :

Degree Verti, 178 Degree Hor. Operation 27x7, Native Resolution 3840 x 2160 (16:9) - UHD, 4 x USB (2 x

2.0, 1 x 2.0 internal, 1 x Type C), 0-40°C, ≤0.5 W, HTML 5 Browser Opera(4.9), Yes(internal) IEEE

802.11 a/b/g/n Dual

WiFi certificated, BIS, YES CLASS A 3dB margin. (Including Five year free maintenance with

Networking Enclosures & Accessories Supply, Installation, Testing & Com mission ingot 24U Wall mount

closed rack with front glass door, fan tray on top, perforated rear doors, keyboard tray with shelf. Casters &

2 nos vertical power strip with std etc as required.

Supply, Installation, Testing And Commissioning of Layer 2 Managed Gigabit POE switch with 24 #

10/100/1000BaseT ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit SFP Port.

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

143 E-143 Supply and laying of Cat-6 STP LSZH UV outdoor cable in PVC conduit with termination as per TIA 200.00 Meter 113.00

SR. No. Item No. Description of Work Unit Rate Amount

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

144 E-144 connections as per site situation directed by Engineer In charge. 1.00 Nos. 159.00

(4) TV Co-axial Socket outlet

Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-

boost charger with IGBT base rectifier & Inverter & sealed maintenance free SMF batteries. The charger

having operating capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with 0.8 load

145 E-145 power factor with battery, over/under voltage output with over load & short circuit protection equipment. 1 Nos. 1,28,815.00

The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted

batteries stand, 10% Overload capacity for momentary load.

(D) 5 KVA with 1Hr Backup

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary

clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete.

For 4.5 Kg Capacity, including maintaining/ renewal validity of all Co2 fire extinguisers up to the

completion of O&M period

Supplying rubber matting of following thickness as per IS : 15652/IEC61111

Providing and erecting metallic vitrified danger notice board for MEDIUM VOLTAGE installation to be

148 E-148 erected as per IS. 2.00 Nos. 69.00

Providing printed instruction chart both in English and Gujarati and duly framed with front glasses, for

149 E-149 treatment of person suffering from Electric shock 2.00 Nos. 129.00

Providing & laying. Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )

Anti Rodent type with necessary connecting accessories of same material at required depth for laying of

150 E-150 cable. below ground / road surface for enclosing cable and backfilling the same to make ground as per 400.00 Meter 62.00

SR. No. Item No. Description of Work Unit Rate Amount

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @

an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚C within a hour, The water

153 E-153 cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank 1.00 Nos. 55,340.00

surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection.

The body of water cooler will be made from Stainless Steel.

Supplying and erecting water filter cum purifier with ultra violate technology. (Aquaguard / waterdoc model

or equivalent symphony/ crystal/videocon model)

S.I.T.C. of single phase submersible pump set suitable for 100 mm size or more dia bore well having motor

capacity and discharge as under with necessary panel box. Lifting and Lowering taken extra.

(c) Motor rating 2 HP (17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for 32 mm dia.

Supplying & erecting approved make Automatic liquid level controller 6A. with sensor testing as per

156 E-156 instruction of Engineer in charge on site complete with wiring connection with existing wires , with copper 1.00 Nos. 2,332.00

conductor from pump to upper and lower tank.

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable

157 E-157 approved make of following Size. 20.00 Meter 103.00

(B) 3 Core x 2.5 Sq. mm.

AIR-CONDITIONERS

Providing and erecting approved make split air-conditioning unit consisting of copper condensing unit with

fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected

evaporating unit and blower motor with its accessories by means of extra supplied proper insulated copper

tubing,drain PVC pipes suitable for ( cost includes powder coated Stand, Eco Friendly green gas charging,

15A plug top & Remote Control) with necessary core cutting.

(1)For ISEER Range (KWH/KWH)(3.1 to 3.99) Premium Category

(b) for 1.5 ton capacity

Providing and erecting approved make split air-conditioning unit consisting of copper condensing unit with

fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected

evaporating unit and blower motor with its accessories by means of extra supplied proper insulated copper

159 E-159 tubing,drain PVC pipes suitable for ( cost includes powder coated Stand, Eco Friendly green gas charging, 4.00 Nos. 58,706.00

15A plug top & Remote Control) with necessary core cutting.

(1)For ISEER Range (KWH/KWH)(3.1 to 3.99) Premium Category

(c) for 1.7 to 2.0 ton capacity

SR. No. Item No. Description of Work Unit Rate Amount

Providing and erecting approved make Cassette type split air-conditioning unit consisting of condensing

unit with fan motor, hermetically sealed scroll/rotary compressor with accessories etc. duly connected

separately erected evaporating unit and blower motor with its accessories by Eco friendly Green gas

charging & Internal copper wiring & Remote control ( 3 star and above of current year) with necessary core

(E) for 4 ton capacity- 1/3Phase

Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR capacity

erected with necessary hardware materials as directed.

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and control

cable,necessary PVC drain pipes for Cassette / Split AC machine up to 4 TR capacity

Liason / Follow UP with Supply Co.

Filling the necessary application to supply co. following up and getting the supply filling the necessary test

report to the supply co. inclusive. All official fees including security deposits will be paid by the client and

out of pocket expenses shall be of contractor.

Total Cost of Electrical, ELV & Heating Ventilation & Air - Conditioning Work

Ahmedabad Municipal Corporation

Construction of Swimming Pool at T.P.-128, F.P.-493 in Vatva Ward, South Zone, Ahmedabad.

BOQ - Filtration Work

Item Description Unit Rate Amount

Supply, installation, testing and commissioning of Short coupled, CED coated, Centrifugal

Horizontal Back-pull-out industrial type pump set with cast iron body, bronze impeller, carbon-

ceramic mechanical seal, stainless steel shaft, with 7.5kW, IE3, TEFC 1450 RPM prime mover

1 suitable for 415V, 50Hz, 3 phase AC power supply, with base-frame, 125 x 250mm stainless 4.00 Nos. 4,25,000.00

steel escentric pre-filter with stainless steel basket, 100mm NRV, 250mm ball type foot valve,

100mm isolation valve and pressure gauge in accordance with technical specification. (2 working

+ 2 standby = 50% standby). Design flow rate 159m3/hr @ 12-14 meter head for each pumpset

Supply, installation, testing and commissioning of 2000MM dia and 3000MM long Horizontal

Bobbin Wound FRP filters 1200mm bed depth. The inner distribution system and under bed

draw off system shall be of hub and lateral type. The filter shall be equipped with man-hole,

2 manometer, air drain, water/sand draining hole, inlet/outlet with flanges and minimum working 2.00 Nos. 14,00,000.00

pressure of 2.5 Kg/ cm2 with 160mm frontal piping with 5 (five) butterfly valves, manometer,

pipe supports and media complete in accordance to the manufacturers specifications. Design flow

159m3/hr each filter. Max permissible velocity 30 M3/ M2/HR

(B) Disinfection System

Supply, installation, testing and commissioning of direct cylinder mounted type gaseous

chlorinator, with vacuum regulator, integrated safety valve, filter and pressure gauge, flow meter,

ejector, non-return valve, PE tubing, ammonia bottle and spanner. Capacity 0-4 kg/hr with

Booster pump, piping, control valves and pressure gauge.

4 Supply of 100 kg filled chlorine gas cylinder in accordance to the specifications 4.00 Nos. 26,945.00

5 Supply of Safety test kit for chlorine gas cylinder in accordance to the specifications 1.00 Nos. 35,000.00

Supply of Double state self contained open circuit compressed air breathing apparatus in

Accordance to the specifications

Item Description Unit Rate Amount

(C) Pool Basin Equipments

7 Regulable floor inlets. 57.00 Nos. 1,000.00

8 Vaccum / Suction inlets 5.00 Nos. 1,000.00

9 Stainless Steel Main drain grills 500 x 500mm. 2.00 Nos. 45,000.00

10 Stainless Steel Main drain grills 300 x 300mm. 1.00 Nos. 24,000.00

(D) Maintenance & Cleaning Equipments

Self Priming Pumpset with built-in pre filter with transparent lid, carbon-ceramic mechanical

seal, stainless steel shaft, rated speed 3000 RPM 440V, 50Hz. Rated flow 30m3/hr

90cm Stainless Steel vacuum head with hooks for attaching towing ropes and 60 mtrs towing

13 Self floating hose 30 mtrs, 50mm dia 1.00 Nos. 15,000.00

14 Telescopic pole 9 mtrs 1.00 Nos. 11,000.00

15 Aluminum reinforced Deep Net, clip type 1.00 Nos. 3,500.00

16 90cm aluminum reinforced curved brush with plastic bristles, clip type 1.00 Nos. 5,500.00

17 450mm Aluminum reinforced curved brush with SS bristles, clip type 1.00 Nos. 4,500.00

18 Providing hand held electronic ORP tester. 1.00 Nos. 15,000.00

19 Providing hand held electronic pH tester. 1.00 Nos. 5,000.00

20 Providing reagent based Residual/Free Chlorine & pH test kit. 1.00 Nos. 2,500.00

(E) Stainless Steel Ladders

Supply, installation, testing and commissioning of Stainless Steel 2 treads ladder with anti skid

Supply, installation, testing and commissioning of Stainless Steel 3 treads ladder with anti skid

Supply, installation, testing and commissioning of Stainless Steel 4 treads ladder with anti skid

Supply, installation, testing and commissioning of Stainless Steel 5 treads ladder with anti skid

(F) Overflow Grating

25 Providing & fixing pool overflow modular grating 345 x 23mm as per specifications 100.00 Rmt 1,640.00

26 Providing & fixing pool overflow modular grating 240 x 23mm as per specifications 41.00 Rmt 1,475.00

27 Gating corner piece 90 deg 345 x 345 4.00 Nos. 3,500.00

Item Description Unit Rate Amount

28 Gating corner piece 90 deg 240 x 240 4.00 Nos. 2,500.00

Supply, installation, joining and testing PVC pipe confirming to IS : 4985 class IV 10Kg/cm2

including all fittings such as such as bends, elbows, reducers, tees, union, coupler, tail piece

flange etc. Cost shall be inclusive for providing supports as per specifications and making good.

Pipes shall be connected to pumps, equipments, valves etc through tail piece flange.

Providing & Fixing sluice Valve of 12" with extended spindle accordance with technical

specifications.

Providing & Fixing sluice Valve of 4" with extended spindle accordance with technical

specifications.

Providing & Fixing 90mm dia PVC double union ball valve to the suction sweeper line in plant

Supply, installation, joining and testing 10" dia Cast Iron D/F pipe as per pump manufacturers

recommendations for pump suction confirming to IS : 1538 including fittings.

(H) Control Panel

Design, manufacture, supply, installation, testing and commissioning of integrated, cubical type

34 dead front, extensional, 16 SWG CRCA sheet steel control panel to the foundation. The control 1.00 Nos. 2,50,000.00

panel should be suitable for 440 volts, 50 Hz, 4 wire supply.

(I) Competition Equipment

35 Providing & fixing S.S. anchors for Anti-wave racing lanes in pool etc.complete. 18.00 Nos. 3,500.00

Providing & handing over of 50 mtrs. anti-wave racing lanes in red, white and blue coloured

floats with Stainless Steel cable, fasteners and hooks.

Providing SS reels/ roller for lane storage. Each roller should be capable to accommodate

(three) 50 meters racing lanes

Item Description Unit Rate Amount

Providing and handing over of 450mm starting platform with a slip resistant top surface, a slip-

38 resistant step and anchors. Platform assembly can be removed by unscrewing fasteners as and 10.00 Nos. 1,25,000.00

when required. The same will be in accordance to the specifications.

(J) Operation & Maintenance

OPERATION & MAINTAINENCE - After commissioning of the filtration plant, the contractor

will run the plant for ONE YEAR. Electricity, water and chlorine gas shall be provided by the

AMC. The work includes operation of filter plant on daily basis and ensuring clean and healthy

water at all times. Maintaining chemical control of water as per standard quality levels, operating

suction sweeper for floor cleaning etc. The client reserves right to renew the said contract for a

further period on a mutual agreeable time and cost.

(K) Office Furniture for Operator

40 Wooden office Table of size 1200mm length x 600mm width 1.00 Nos. 5,000.00

41 Steel Office Chair 3.00 Nos. 3,000.00

42 Steel Cupboard (4 feet H x 3 feet W x 1 feet 4 inch D) 1.00 Nos. 16,000.00

Total Amount of Filtration Work

Total Amount of Filtration Work

Ahmedabad Municipal Corporation

Proposed Construction of Swimming Pool at T.P.-128, F.P.-493 in Vatva Ward, South Zone, Ahmedabad.

BOQ - Self Supporting Roofing Work

Item No. Item Description Unit Rate Amount

Providing, Fixing, Installation of Proflex - Self Supported Galvalum Roofing of Proflex from

M&B Engineering Ltd or Equivalent with proper overlapping and seaming between different

sheets without making holes or preventing the overturning the roof by wind addition made up

from superior quality, structural grade steel. Base metal width 914 mm with tolerance of +/-

mm, Steel Grade : Grade D Regular Modified Polyster Imported Color Coated Galvalume

Steel having Profiled width of 625 mm +/-10 mm. Design, supply, & fabrication of self

1 supported single span arch roof fabricated from mechanically seamed manufactured by

American Hydraulic Machines to profiles of Imported Galvalume Cold Rolled Structural Steel

coils as per standard ASTM A792, Steel Sheet, Aluminum-Zinc Alloy Coated by Hot-Dip

Process. The work should be carried out by specilialize and approved agency only. The rate of

item is including fitting as per standerd specification. The vendor shall give windload End

Reaction before start of the work and the vendor shall be entirely responsible for the damage

of the same during transport, installation and even after installation upto 1 years.

Thickness 1.60 mm BMT, 1.65 mm APT with tolerance of +/- 0.02 mm, Coil Width 912 mm

tolerance of +/- 0.04 mm, for upto 31 Mtr Span Length 63 Mtr

Thickness 1.00 mm BMT, 1.05 mm APT with tolerance of +/- 0.02 mm, Coil Width 912 mm

tolerance of +/- 0.04 mm, for upto Span: 16 Mtr and Length 20 Mtr

Providing and fixing of hangers/clamps as per requirement for laying of cables and hanging Piece

of bulbs from Self Supported Proflex Systems Roofing. (Nos)

Total Amount of Self Supporting Roofing Work

Total Amount of Self Supporting Roofing Work

Ahmedabad Municipal Corporation

Proposed Construction of Swimming Pool at T.P.-128, F.P.-493 in Vatva Ward, South Zone, Ahmedabad.

BOQ - Fire Fighting Work

Sr.No. Item Description Unit Rate Amount

Supplying, installing, testing and commissioning of electrical operated end suction, back pull out type,CI closed casing, SS shaft & Bronze

impeller, mechanical seal, booster pump of capacity 900 LPM and gainst head of 35m with a pressure of 4.5 kg/cm2 at the nearest & top

most hydrant with Booster starter. M.S. frame & clamps as necessary for fixing the pumps on the top of slab as per site condition and

instructions of site enGIneer in charge .

Supplying, installing, testing and commissioning of Control Panel for Booster Pump to start the booster pump with cabling from

Booster Pump to Panel at Terrace Level.

3.0 3.Core x 10 Sq.mm Copper armoured cable for pump to panel 30.00 Meter 907.40

4.0 Providing, fixing, testing and commissioning of Pressure Gauge with Ball Valve 2.00 Nos. 3,200.00

Providing and fixing, testing and commissioning of C.I.Butterfly valve PN16 with Flanges. conforming to I.S:13095, Nut bolts, Gaskets

completed as required.

Providing, fixing, testing and commissioning of C.I. Dual plate type Non-Return Valve class PN 16 rating with fittings, flanges, nutbolts,

washers, gaskets etc.of sizes:

7.0 Providing and fixing, testing and commissioning of Y Type Strainer.

Providing, fixing, testing and commissioning of Above Ground MS C Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.) and IS:

3589 (upto 200 mm dia. And above) including cutting, screwing, welding etc. and providing all fittings like flanges, bends, tees, elbows,

reducers, clamps, hangers etc. with painting of one coat of primer and 2 or more coats of synthetic enamel paint of approved make / shade

complete as per specification.

8.2 80mm dia. 6.00 Meter 1,943.00

8.3 50mm dia. 6.00 Meter 1,237.00

8.4 25mm dia. 6.00 Meter 595.00

Providing, fixing, testing and commissioning of Under Ground MS C Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.) and IS:

9.0 3589 (upto 200 mm dia. And above) with IWL/pypecoat, 4mm thickness wrapping and coating and providing all fittings like flanges, tees,

elbow, fasteners with all required.

Fire Fighting Equipement

Providing, fixing, testing and commissioning of SS Single Headed Oblique Pattern Hydrant Landing Valves as per IS: 5290 with 80 mm

dia flanged inlet & 63 mm dia female outlet complete with cap and chain etc.

Providing, fixing, testing and commissioning of SS Branch Pipe with nozzle of 25 mm nominal bore outlet suitable to fit with standard

instanteneous type 63 mm dia coupling. As per IS:903

Providing, fixing, testing and commissioning of 63 mm dia 15m long RRL Hose Pipe with 63 mm dia.Type A Male and female Stainless

Steel couplings duly binded with GI wire, rivets etc. conforming to IS 636 as required.

Providing, fixing, testing and commissioning of weather proof standard fire Hose Cabinet wall mounting type 18 Guage. (750 x 600 x 250)

having Double Opening with M.S. fabricated stand, necessary locking arrangement by allan key.

Sr.No. Item Description Unit Rate Amount

Providing, fixing, testing and commissioning of Wall mounting swing type first aid Fire Hose Reel with drum, hanGIng bracket, 30 M x

25 mm dia high pressure hose reel tubing as per IS:884 with shut nozzle and ball valve and all required accessories.

15.0 Providing, fixing, testing and commissioning of CI Two way Fire Brigade Inlet for system filling from Fire Brigade Tender. 2.00 Nos. 12,480.00

Fire Extinguisher.

Providing & fixing of 6 Kg Fire Extinguisher Mono Ammonium Phosphate Powder 50, Stored Pressure Type, Pressure Gauge,

16.0 Controllable discharge mechanism Class A Rating 3A & Class B rating 21B as per IS 15683 ISI MARK (ABC Dry Chemical Powder - 20.00 Nos. 2,118.00

Providing & fixing of CO2 type Fire Extinguisher of capacity 4.5 kg filled with Co2 Gas as per IS 15222 with controll discharge

17.0 mechanis, fitted with Hose & Horn applicable on Class B fire rating 21B confirms to IS 15683 bearing ISI mark. Co2 cylinder as per IS 20.00 Nos. 4,810.00

Providing & fixing of Mechanical Foam 9 Ltrs. Stored Pressure Type Controllable discharge mechanism applicable on Class A & B Fire

Rating 2A & 21 B

Manual Fire Alram System. 0.00

19.0 Providing, fixing, testing and commissioning of Manual Call Point. 4.00 Nos. 518.00

20.0 Providing, fixing, testing and commissioning of Hooter 4.00 Nos. 658.00

Providing, fixing, testing and commissioning of Fire Alarm Panel

22.0 Providing, fixing, testing and commissioning of 2 Core X 1.5 Sqmm Flexible Cable with PVC Conduit. 250.00 Meter 160.00

On - Off Pump Trigger System.

23.0 Providing, fixing, testing and commissioning of On -Off Switch. 6.00 Nos. 890.00

24.0 Providing, fixing, testing and commissioning of 3 Core X 1.5 Sqmm flexible Cable with PVC Condiut. 500.00 Meter 210.00

Providing, fixing, testing and commissioning of 25 mm dia Air Release Valve and Ball Valve assembly on top of each riser for Air release

Providing, fixing, testing and commissioning of below Auto Glow Signages.

26.0 Emergency Exit 4” X 12” 15.00 Nos. 450.00

27.0 Fire Hydrant 4” X 12” 2.00 Nos. 450.00

28.0 Fire Hose Reel.4” X 12” 2.00 Nos. 450.00

29.0 " ABC" Extinguisher 8"x 4" 20.00 Nos. 550.00

30.0 "CO2 " Extinguisher 8"X 4" 20.00 Nos. 550.00

32.0 Supply, Installation of Steel Structure Support. 500.00 Kg 145.00

Sr.No. Item Description Unit Rate Amount

Fire Rated Steel Doors with steel frames as per BS:476 (20&22), IS 3614 (Part-2) for stability and integrity. pressed Galvanized steel

conforming to IS 277 with the following specification. recommended fire door shell have doors tested at CBRI for maximum rating of

Door frame shall be Single rebate profile of size 105 x 57 mm made out of 1.60mm (16gauge) minimum thick galvanized steel sheet.

Frames shall be mitered and field assembled with self-tabs. All provision should be mortised, drilled and tapped for receiving appropriate

hardware. Rubber door silencers should be provided on the striking jamb. Frames should be provided with back plate bracket and anchor

fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement & sand slurry

necessary for fire doors on the clear masonry opening.

33.0 Door leaf shall be 46mm thick fully flush double skin door. Door leaf shall be manufactured from 1.2mm (18guage) minimum thick 3.00 Sqm 33,500.00

galvanized steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The

infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for receiving appropriate hardware and provided

with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair

of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be

provided as per manufacturer's recommendation with a beading and screws from inside. The glass should be 6mm clear borosilicate fire

rated glass of relevant rating of the door.

All doors and frames shall be finished with polyurethane aliphatic grade paint of approved color. The door leaf and frame shall have passed

minimum 250 hours of salt spray test. Rate should include supply and installation of door and hardware set as mentioned in the door.

Hardware Fittings Make :- Doorma , Geze , Hafales

APPROVAL FIRE SYSTEM FROM LOCAL FIRE AUTHORITY

34.0 Getting of Fire Fighting System Approval from local fire authority with all other charges and documentations for getting No Objection 1.00 Job 1,80,000.00

Non Comprehensive Quarterly Maintenance service charge for Fire Fighting System including servicing of fire fighting system with

cleaning ,oiling and Greasing of fire fighting equipment's, give live demonstrations And performing live mock drill once in a year of the

system after completion of DLP.

Quarterly servicing and maintenance will be done for Fire Fighting systems.

a) To check & Maintain the Fire Fighting System as per Installation done.

b) Checking of Butterfly valve , NRV, Ball valve for smooth operation.

c) Checking of Fire Brigade Inlet.

d) Visually check of Sprinklers for Leakage.

e) Fire Extinguisher to be checked physically.

f) Testing of Main Pump, Sprinkler Pump & Jockey Pump, Fire Panel.

g) Physical checking of each Fire fighting Equipment's. (Like Hydrant Valve , Hose Reel,Hose Box , Hose pipe And Branch Pipe etc..)

h) Checking of Pump room in active working condition.

I) Refilling of Fire Extinguisher will be in contractor scope as per client requirements.

J) Including Charges for fire New / Renewal NOC, for Fire Fighting System.

K) Videography , Photo graphy , numburing & Pendrive etc. as per norms for New / Renewal NOC.

35.1 First Year 4.00 Job 36,158.40

35.2 Second Year 4.00 Job 45,198.00

35.3 Third Year 4.00 Job 54,237.60

Total Amount for Fire Fighting Work

Total Amount for Fire Fighting Work