PROVN OF 02 TOILET AND 02 BATHROOM NEAR BLDG NO. P-4, SPL REP TO BLDG. NO P-288 DSOI AND PROVN OF PARKING SHED NEAR OTM ACCN OF 110 MC/MF DET REST CAMP UNDER GE DEHRADUN

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in hard/dense soil complete all as specified and as directed .

M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed .

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortor 1:6 complete all as specified and as directed .

M&L Brickwork with subclass ‘B’ bricks in cement mortar 1:4, straight or curved on plan to any radius in half brick thick walls built in

M&L cement concrete 1:2:4 type B0 40mm thick in Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified.

M&L for RCC Type B-1, M-20 nominal mix (20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L for Providing precast cement concrete M-20 nominal mix type B1 (using 20 mm graded aggregate) set in cement mortar 1:4 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Ditto, as above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

M&L Formwork flat fair finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:4), finished surfaces even and smooth complete all as specified and as directed.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:6), finished surfaces even and smooth complete all as specified and as directed .

Preparing of new surfaces of walls and applying two coats of cement base paint, complete all as specified and as directed .

Preparing new plastered surfaces and applying 3 coats of white wash on walls complete all as specified and as directed .

M&L for hardcore of gauge exc 63 mm but n.exc 100 mm deposited, spread and leveled in layers n.exc 15 cm thick, watered and rolled/rammed to a true surfaces in broken stone or boulder complete all as specified and as directed.

M&L 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone agg as in sub base complete all as specified and as directed by the Engr-in-Charge.

M&L for cement concrete type B-1 (1:2:4) (20 mm graded stone aggregate) 25 mm thick as in floor finished complete all as specified and as directed .

M&L for screed bed bedding 15 mm thick in cement mortar (1:6) for floor laying floor finish complete all as specified and as directed .

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match complete all as specified.

M&L for coloured digital ceramic tiles in vertical surface 375 x 250 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in CM (1:3) complete all as specified.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone agg as in plinth protection complete all as specified and as directed.

S&F Aluminium Anodised window and ventilator shutters, side hung/sliding /fixed type with out sash bars,aluminium sections weighing 0.55 kg/m including necessary joining cleats,glazing clips,rubber packing,anodised alminium snap beading ,screwes,anodised fitting such as peg stays 150 mm long (01 Nos),hinges type B-21 100 mm long (02 Nos) ,suitable handle (01 Nos) etc including powder coating of any colour (min thickness of powder coating n less than 50 micron) complete all as specified and directed by Engr-in-charge.

S & F for PVC solid factory made door frame (chowkhat) of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening as per specification and drawing complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gab insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as shown in SSR Part-II and as directed by Engineer in Charge.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 150 mm long Aluminium anodised handles of fabricated type complete all as specified and as directed by Engr-in-Charge.

S & F Butt hinges 100 mm size medium weight cold rolled stainless steel and fixed complete all as specified and as directed by Engr-in-Charge.

S & F for 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy & fixed and compete all as specified and directed.

Supplying, fixing, jointing and testing galvanised steel water tubing 15 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

Supplying, fixing, jointing and testing galvanised steel water tubing 20 mm dia bore medium grade with all fittings such as bends, tees, nipples, elbows, socket reducers, etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) water closet, including connection to trap and to flushing pipe, anti syphonage pipe etc, and making good to floor complete all as specified and as directed by Engr-in-Charge.

S & F 10 litres capacity PVC low level valve less symphonic action type flushing cistern white with inlet, float valve, float and handle including brackets with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed by Engr-in-Charge.

Supply only PVC connection 15 mm dia 450 to 600 mm long with brass fly nut at both ends complete

S&F 500 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, including supply & fix 20 mm dia GI light grade wash out pipe 450 mm long with plug and 20 mm dia GI light grade over flow pipe 600 mm long with fitting complete all as specified.

Supply & fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 25 mm bore size complete all as specified.

S&F 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

S&F Vitreous China wash hand basin, white, oval type counter top of size 550mm x 400 mm fixed on and including cast iron cantilever bracket, 32 mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete. Note: Pillar tap shall be measured as supply only under respective item.

S&F 15mm dia swan neck pillar tap (for oval type WHB) brass chromium plated with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 15 mm dia bore chromium plated concealed stop cock, complete

S & F brass chromium plated angle cock 15 mm dia screwed for iron pipe or brass ferrule complete

S & F 15 mm bore bib taps, chromium plated cast copper alloy long body, screwed down, screwed for iron pipe or for brass ferrule complete

S & F Chromium Plated brass soap dish fixed to wall with chromium plated brass screwed and cup washer complete all as specified and directed.

S & F brass chromium plated towel rail, 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

M & L PVC (SWR) floor trap plain with grating including jointing with solvent cement 75 mm bore outlet complete

S & F PVC (SWR) soil waste & vent pipe in any length without ears laid in floors, trenches or fixed to wall complete for 75 mm dia bore of pipe complete

S & F PVC (SWR) soil waste & vent pipe in any length without ears laid in floors, trenches or fixed to wall complete for 110 mm dia bore of pipe complete

S & F PVC (SWR) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 75 mm dia pipe.

S & F PVC (SWR) bends, T, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 110 mm dia pipe.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W(Gde E-250) quality-A all as specified and directed

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified and as directed by Engr-in-Charge.

Removing excavated material n.exe 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

9.S&F 150 mm Salt glazed stoneware drain pipes, grade ‘A’ complete all as specified and diirected

10.M&L cement concrete 1:3:6 type C2 concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in 150mm dia pipe.

11.M&L providing precast cement concrete type 1:2:4 (using 20mm ) in landing, cover slabs (for manholes etc) all as directed.

M&L for construction of Soakage wells 2.4 m internal dia and 3.0 m effective depth complete all as specified in PS here in after and shown on drawing No CEBZ TD Drawing No. 309 Sh 1 to 4/4.

M&L for pre-polished pavement coloured chequred tiles glossy finish of size not less than 300 x 300 x 20-22mm thick with anti skid properties laid over 20 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concretebut excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and ditected.

M & L for RCC M-25 { using 20 mm graded stone aggregate) in slab supported wall beam, columnn in fllors, roofs landing , balconies, canopies, deck slabs and the like etc complete all ass specified and directed

Use and waste for Formwork to to soffites of suspended slabs such as roof slabes, fllor slabes including edge Complete all as specified

S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls/chajja covering etc fixed with self tapping screws as specified

M&L for 100 mm thick cement concrete 1:4:8 type D2 40mm graded crushed stone aggregateas in sub floor all as specified and directed

M&L 75mm thick PCC 1:3:6 type C-2 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand mixer 1:3 by weight, surface finished even and fair without using extra cement complete all as specified

Taking down cement plastering of any description on brick/stone/concrete wall surfaces of any description incl racking out joints hacking for key,scrubbing down with water etc. complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in leveling course to floors complete all as specified

M&L vitrified ceramic coloured tiles 10 mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified

All as per item No-68 here in above but as in skirting and including 10 mm thick rendering in cement mortar 1:4, complete all as specified

S&F in repair aluminum alloy powder coated door made out of hollow extruded aluminum section as mentioned below. Each door having 02 Nos Disc or D type handle, 02 Nos aluminum tower bolt 200 mm size, one brass mortice lock of six lever with key in duplicate regulated by double action hydraulic floor spring heavy duty (Make:- Sandhu/Ritz) shutter to be partly glaze with 5mm thick tined coloured glass in upper pannel and partly pannelled with 12mm thick both side laminated particle board in lower pannel fixed with glazing clip, rubber beading/gasket, anodised aluminum beading screw complete all as specified and directed at site. Chowkhat Frame:- 101.60x44.45x1.60mm Shutter verticle style :- 85x44.45x1.56mm shutter middle Rail :- 83.50x44.45x1.54mm Shutter Top Rail and bottom Rail :- 114.30x44.45x1.55mm Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

S&F in repair aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one nos wire gauged shutter sliding type, with aluminum sections as per Series-A(15mm) 3 track of Jindal section numbers for sliding windows, and glazed with tinted glass coloured glass 4mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum tower bolt 150mm long etc complete all as specified and directed. Shutter Top & bottom size : 37.50x15x1.60mm Shutter inner lock size 37.50x15x1.60 mm Shutter side (Handle) size 37.50x15x1.36 mm Chowkhat bottom size : 50.30x26x1.20mm Chowkhat top & sides size: 50.30x26x1.00mm . Make: (i) Anodised aluminum section : Jindal / Hindalco / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

Taking down chowkat with shutter exc 1.5 Sqm but n.exc 4 Sqm each complete all as specified and as directed by Engr-in-Charge.

M & L for POP false ceiling with cornice of approved design including GI Frame work and wirmess complete all as specified.

M&L new plastered surface of walls treatment painted surfaces of external wall with scrapping, wire brushing, washing with water preparation of old plastered surfaces of external wall two coats of exterior grade 1st quality weather coat paints over a coat of alkaliresistant priming paint complete all as specified and directed.

M&L for preparation of wallls incl corners and applying two coats of distemper oil emulsion over applying of 2-3mm thick wall care putty finish wall surface even & smooth by roller complete all as specified and directed.

S & F Vanishing blind Zebra Roller Coard Drawn ( Polyeaster) Horizontal type strip of approved colour weight not less then 2 Kg/Sqm Complete all as specified and directed .

S&F powder coated aluminium grill with mesh size 75 mm and aluminium bar 6 mm XPM type including all accessories such as channels for fixing grill screws etc. aluminium section 15 micron thick anodizing complete all as specified and directed including taking down old grill and removing from site.

S & F in repair 10 mm thick not skid rubber tiles of compsitionn of Recycled rubber -97 % Urethane Binder-3% of tensile strenth 350 PSI Electrical resistance fixed with adhessive compltee all as specified.

M&L complete removal of existing treatment painted surfaces of external wall with scrapping, wire brushing, washing with water preparation of old plastered surfaces of external wall two coats of exterior grade 1st quality weather coat paints over a coat of alkaliresistant priming paint complete all as specified and directed. Make : Berger XP advance (long life exterior emulsion paint), Asian Paints (Apex Ultima), Nerolac (Excel total)

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface, complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete 1:2:4, type-B2 (40mm graded aggregates) as infoundations, filling and mass-concrete, complete all as specified and directed by Engineer-in-Charge.

S&F for Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 Gde E-250, Quality 'B', complete all as specified and directed by Engineer-in-Charge.

S & F for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240, complete all as specified and directed by Engineer-in-Charge.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work complete.

M&L for preparation of new surfaces of steel or iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multi stranded copper conductor single core FRLS cable 3 run (N+P+Earth) drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including cutting chases for conduits and making good to walls, floors etc as per existing one complete all as specified and directed.Note :(1) The wiring to be done as per IE rule and maintain colour code accordingly.(2) modular boxes & modular combined cover plates shall be paid separately under respective items.

All as per item No.86 here-in-above but for one pin 5 A socket outlet independent point

All as per item No.86 here-in-above but for one pin 5 A socket outlet on same board

All as per item No.86 here-in-above but with 4 Sqmm cable for one 6 pin 15A socket outlet point on independent board

All as per Item No 86 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated copper conductor and 1.5 Sqmm copper conductor for continuous earthing complete.

M&L rigid PVC conduit in concealed conduit duly chases cutting and including making good for drawing of Telephone cable/Cable for TV (VGI Cable ) /Internet Cable complete all as specified and directed.

S & F Switch piano flush type single pole one way 6 Amp complete all as specified and directed.

S & F Switch piano flush type single pole one way 15 Amp complete all as specified and directed.

S & F Socket outlet 3 pin , 5/6 Amps flush type multipurpose 5 pin complete all as specified and directed.

S & F switch socket 2 in 1, 3 pin , 15/16 Amps flush type universal multipurpose complete all as specified and directed.

S&F ceiling rose surface Bakelite 3 terminals of size 65x25mm complete all as specified and directed.

S & F Lamp holder with , insulated body, with back plate suitable for batten fittings complete all as specified and directed.

S&F switch modular 6 Amps 230 Volts one way switch complete all as specified and directed.

S&F Socket modular 6 Amps AC 230 Volts 2/3 pin combined 2 modular type complete all as specified and directed.

S&F Socket 6A/16 Amps-2/3 pin combined AC 230 Volts modular type complete all as specified and directed..

S&F Switch modular type AC 230 volts 16 Amps one way complete all as specified and directed.

S & F Modular Fan Regulator electronic rotary,0-4 steps step type 100 Watt, 240 Volt 50 Hz hum free 2 module complete all as specified and directed.

S&F modular bell push 6 Amp one module one way complete all as specified and directed.

S&F modular TV Socket out let with single port complete all as specified and directed.

S&F modular RJ11 Tele Jack double port with shutter port complete all as specified and directed.

S&F Calling Bell (Pilot Ding Dong - 1, Rose Mary Ding Dong -1, City Ding Dong -1, Cindrella Ding Dong-1) complete all as specified and directed.

S & F Modular white cover plate with frame 2 module and metal flush box 2 module complete all as specified and directed..

S & F Modular white cover plate with frame 3 module and metal flush box 3 module complete all as specified and directed..

S & F Modular white cover plate with frame 4 module and metal flush box 4 module complete all as specified and directed..

S & F Modular white cover plate with frame 6 module and metal flush box 6 module complete all as specified and directed..

S & F Modular white cover plate with frame 8 module and metal flush box 8 module complete all as specified and directed..

S&F LED tube light alluminium extruded body with integrated electronic driver , 20 W complete all as specified and directed. Make: Wipro Cat part No LL20-281-XXX-65AL1/Philips cat part No BN021C LED20S PSU CWGR S2/Havells Cat No ENDURA LINEARNEOBS20W LED865SPCWH.

S&F LED down lighter concealed ceiling light 12W Sky Spot COB (WW) complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F in replacement surface mounted LED 600x600mm fitting made of CRCA powder coated finish with high transitivity diffuser, LED used shall be profit LED & flat diffuser type and capacity 32 wattage or higher wattage, CCT up to 6500K, CRI > 80, PF > 0.95 or higher side including driver minimum internal surge protection 2.5 KV complete all as specified & directed. Make : Philips cat part No SM365C LED32-6500 PSU OD WH/Wipro CRCO10R038HP57GL/Havells PLUTONEO2X2PLR34WLED857S/CG LSTP-45-CDL.

S&F LED down lighter concealed ceiling light 1W 1 ,Warm white colour , Dimension : 30mm x 25mm , Ceiling Cut-out : Ø 25mm Spot COB (WW) complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F LED Strip Tube type 50 Mtr Roll (colour - White, Red & Green) with driver , connector complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F LED Scenery Light complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F LED Mirror light fitting tube light alluminium extruded body with intergrated electronic driver along with fixture, 10 W complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base LED Lamp/1 N x 7.5 W LED filament lamp complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F wall mounted fans complete with all accessories ,400 mm . BEE 5 star rated PVC AC single Phase 230 V / 240V 50 Hz of , connector block of fan including fixing of Fan hooks and necessary nuts and bolts complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F BLDC Fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep. PVC AC single Phase 230 V / 240V 50 Hz of , connecting up ceiling rose to connector block of fan including fabricating and fixing of Fan hooks from ceiling truss/angle iron, required length of down rods (As per site requirement) and necessary nuts and bolts complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F Exhaust fan exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, complete with louvers, shutters and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F Exhaust fans AC single phase 230/ 240 V of size 150 mm sweep,50 Hz with louver of size 300 mm sweep, complete with louvers, shutters and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block including taking down old metalic exhaust fan complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F Supply and fix Water heater storage type, electric, capacity 35 litres AC single phase 230/ 240 V o and connecting up including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F flood light fittings. Energy saving environmental friendly, long life, exclusive innovative epoxy powder coated die-cast aluminium housing IP66 flood light with high power LED's as light sources, suitable for high lighting architectural features or retail spaces as 82/100/110 watt or higher size LED , Glass cover, fixed on pole duly fixed on angle iron bracket complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F flood light fitting 50 Watt . (Colour - Red-1 White-1 & Green-1)Energy saving environmental friendly, long life, exclusive innovative epoxy powder coated die-cast aluminium housing IP66 flood light with high power LED's as light sources, suitable for high lighting architectural features or retail spaces , Glass cover, complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S & F sheet metal enclosure TPN for DB's when MCB's to be used 8 way with 200 amps bus bar and double door complete all as specified and directed.

S&F Residual Circuit Breaker (RCCB) for earth leakage, overload & short circuit protection four pole 30 mA of capacity 100 Amps complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S&F in repair, MCB DB, sheet metal enclosures double door SPN 8 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F Residual Circuit Breaker (RCCB) for earth leakage, overload & short circuit protection double pole 30 mA of capacity 25 Amps complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor.

S & F MCB SPN 32 Amps,240 Volts,10 KA 'C' series with all incoming/outgoing connections with proper size of lugs complete all as specified and directed.

S&F MCB SP 6 to 32A 10KA, C Curve complete all as specified and directed.

M&L for sub main wiring with 3 runs(1 run for Phase+1 run for Neutral &1 run for Earth, with approved colour code as per EI rules) of 4 Sqmm single core, PVC insulated, unsheathed, multi stranded copper conductor FRLS cable 1100 volts grade drawn through and including concealed wiring with PVC conduit pipe of medium duty not less than 15 mm dia including necessary steel conduit specials and connecting with suitable size thimble, and making good surface of disturbed wall/ceiling/floor as match with existing complete all as specified and directed. Note:-3 runs of 4 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 133 here in above, but 3 run of 6 Sq mm copper cable complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor complete all as specified and directed. Note:- Test certificate shall be submitted by the contractor. Note:-3 runs of 6 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 42 here in above, but 6 run of 6 Sq mm copper cable (3run -Phase, 1 for Neutral & 2 Runs for Earth with recommended colours) and drawn through not less tha 32 mm dia PVC conduit complete all as specified and directed. Note:-6 runs of 6 Sqmm size PVC copper cable and one run of PVC conduit shall be measured as one unit length.

S&F water storage type of Geyser 25 Ltr capacity (Copper Tank) with 5 star BEE rating with all fixing arrangement including nuts, bolts, washer including brackets etc as required complete all as specified and directed.

S&F PVC connection pipe (suitable to cold water) of 15 mm dia, 450 mm long with two brass CP hexagonal nuts adopter rubber washer complete all as specified and directed.

S&F PVC connection pipe (suitable to Hot water) of 15 mm dia 450 mm long with brass flexible tube along with CP Hexagonal nuts adopter rubber washer complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 25 Sqmm 4 Core complete all as specified and directed.

Supply and Laying XLPE insulated galvanised steel strip or wire armoured electric power cable with stranded aluminium conductor 1100 V grade of size 95 sqmm 3.5 core after cutting to required length with necessary glands, nuts, bolts, and lugs complete all as specified and directed.

Excavation in trenches n exc. 1.5 m wide and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete.

Supply & laying Sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable ) and gently punned down to 18cm thickness all complete all as specified and directed. Note :- Only punned down sand thickness 18CM shall be measured and paid.

Supplying and laying old size bricks, laid flat ie length of brick shall be laid across the cable, common burnt clay building bricks sub class `B' designation 75 complete all as specified and directed and testing on completion complete all as specified and directed.

M&L for laying reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm to underground cable laid dry flat over the cable with width equal to length of the cable and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cable for cable protection in trenches all as specified and directed by Engineer-in-Charge.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

M&L Copper earthing with 3 mtr depth . 80 mm dia Electrode ( copper Earthing 50mm) Supply of Advance Maintenance Free Chemical Gel Earthing Electrode (Medium) Copper 80mm Dia 3Mtr Long, inner pipe 48 mm dia Filled With Highly Conductive etallic Compound Mixture CCM, With The Permanent Sealing Of The Both End , Outer Dia Pipe 50 mm With The Strip Terminal 50x6, Terminal Hole, Include with one 50 kg ,bag of bfc Compound (incuding installation) and including all excavation and earth work & connecting the earthing to an earthing test point /transformer nuetral/body/ Lt panel etc. and testing on completion, complete all as specified and directed.

Cutting existing road/hardstand of any type by using crow bar chisel up to a depth of 30 cm for laying GI pipe including making good the surface by returning filling watering ramming in layers 150 mm thick PCC 1:2:4 over 200 mm thick hard core of broken bricks/stones over returning filling watering ramming in layers not exceeding 25 cm thick complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundation of stay assembly etc including necessary form work, complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles , including necessary form work finishing even and smooth without using extra cement complete all as specified and directed.

S&F thermoplastic Polycarbonate IP 65 Distribution LT Panel Board in accordance with IEC 60 529 (Dust Proof, Water Proof & Weatherproof) Thermoplastic Polycarbonate DB of Shock proof, Rust Proof, Corrosion Free, Acid & Chemical Resistant, Fire Retardant & Self Extinguishing, UV Resistant, Silica and Halogen Free recyclable material. Type tasted as per IEC 61 439-1. Total Insulated with System Voltage 415V AC, 50Hz, and 5 wires. The board/panel should be UV resistance in accordance with IEC 61439-1, clause 10.2.4:The panel should be anti-acid & anti corrosive. Degree of protection against mechanical load should be IK08 ( 5 Joule) in accordance with IEC 62262. with suitable rated copper bus Bar.

The panel Having following switch gears :-

Outdoor Floor mounting

Incomer-

250A 4P On load Change over switch - 1 Nos

250 Amps 4P, 35 KA MCCB- 01 Nos.

Multifunction Meter-01 Nos.

RYB Indication Lamp -01 Nos.

In built 3 Phase KWH Meter with necessary rated CTs - 1

Outgoing-

63 Amp TP,25KA MCCB- 05 Nos.

S&F Sheet metal enclosures with socket plug top and MCB' SPN with a two pin and earth plug and socket complete with one single pole 20 A MCB complete all as specified and directed.

Supply and install hi wall split unit indoor/out door split type 2 Ton AC 230 Volts 50 Hz, with cordless remote control unit with inbuilt air ironiser and plasma filter for better air quality complete all as specified and directed.

Supply and install Wall mounted Digital voltage Stabilizer 5 KVA for split type 2 Ton AC 230 Volts 50 Hz, complete all as specified and directed.

AYUSH CONSTRUCTION COMPANY

M/s RAM RATAN AND SONS