C/o 10.00 meter Indoor Shooting Range at Nahan, Sirmaur (HP)

Amount

Excavation in foundation, trenches etc. in earth work in all heights & depths in all kinds of soil including struated soil comprising of pick work, jumper work, blasting work ( both soft & hard rock ) & shall be excavated with chiselling & wedging out rock ( where blasting is prohibited ) and their interemediate classification of soil including dewatering wherever required setting out to required lines, level as shown on the drawing and as directed by the Engineer-in-Charge at site, according to the HPPWD specifiction of 1990 volume-I and sorting out useful & unuseful materials & stacking the same in all leads and lifts and transportation of the unuseful materials for disposing at dumping sites ( to be arranged by the contractor )through all modes of transportation including head load,animal load or mechanical means along with its levelling fine dressing & all labour machineries materials, tools equipements and safety measures & incidentals necessary to complete the work by mechanized means and labour ( If required ). All useful materials such as stones, shingles, aggregate and slates shall be sorted along road side to the maximum possible extent in all leads and lifts through all modes of transportation and used and removed as per the direction of Engineer-in-Charge .Any loss to the public and private properly during the course of execution and dispoal of serviceable and un-serviceable materials shall be the aboulute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Excavation in earth work in drains and channels in all heights & depth in all kinds of soils, including struated soil comprising of pick work, jumper work and blasting work ( both soft & hard rock ) & wedging out of rock,( where blasting is prohibited ) and their interemediate classification of soil including dewatering wherever required, setting out to required lines, grades, side slopes, trimming bottoms and levels as shown on the drawing and as directed by the Engineer-in-Charge at site, according to the HP.PWD., specification of and sorting out useful unuseful materials and stacking the same in all leads and lifts and levelling and disposing of surplus excavated earth in acquired width of road or on approved dumping sites which will be arrange by the contractor at his own level and dumping charges if levied will be born by the contractor through all modes of transportation and used/ removed as direction of the Engineer-in-Charge including head load,animal load or mechanical means along with its levelling fine dressing & all labour,machineries,materials tools equipments and safety measures and incidentals necessary to complete the work by mechanized means & labour ( if any required ).All useful materials, such as stones, shingles, aggregate and slates shall be sorted out and stacked along road side to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per direction of Engineer-in-Charge. Any loss to the public and private properly during the course of execution and dispoal of serviceable and un-serviceable materials shall be the aboulute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Earth work in excavation for structures as per drawing & technical specifications clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleterious materials & disposal upto all leads & lifts, dressing of sides & bottom & back filling in trenches with excavated suitable materials in all kinds of soil as per entire satisfaction and direction of the Engineer-in-Charge.

Filling in plinth with sand under floors including watering ramming consolidating & dressing complete as per HP.PWD., specification 1990 volume-I ( one ) including carriage of all labour equipments & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing form work with steel plates 3.15mm ( Three decimal one five milimeter ) thick welded with angle iron in frames 30x30x5mm ( Thirty into thirty into five milimeter ) ,so as to give a fair finish including centring,shuttering,strutting and propping etc. with wooden battens & ballies, height of propping and centring below supporting floor to ceiling not exceeding 4.00 mtrs ( four meters ) & removal of the same for in-situ reinforced concrete and plain concrete work as per HP.PWD., specification 1990 volume-I ( One )including carriage of all labour equipments and materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in-Charge in :-

Flat surface such as soffits of suspended floors, roofs, landings and the like floors etc. upto 200mm ( Two hundredmilimeter) in thickness

Columns, pillars, posts and struts, square, rectangular or polygonal in plan.

Beams, cantilevers,girders and lintels sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1.00 mtrs ( One meter )in depth in all heights from floor level.

Edges of slabs and breaks in floors & walls under 20cm ( twenty centimeter ) wide in all floor level.

Providing & laying cement concrete 1:6:12 ( One cement : six approved sand : twelve graded crushed stone aggregate 40mm ( forty milimeter ) nominal size ) and curing complete excluding cost of form work in foundation & plinth as per HPPWD. Specification 1990 volume-I ( One ) including carriage of all labour equipments and materials to various location through all leads,lifts and other incidental charges complete as per the entire satisfaction of the Engineer-in-Charge.

Providing & laying cement concrete 1:4:8 ( One cement : four approved sand : eight graded crushed stone aggregate 40mm ( forty milimeter ) nominal size ) and curing complete excluding cost of form work in foundation & plinth as per HPPWD. Specification 1990 volume-I ( One ) including carriage of all labour equipments and materials to various location through all leads,lifts and other incidental charges complete as per the entire satisfaction of the Engineer-in-Charge.

Provding & laying upto floor two level cement concrete including mechanical mix 1 : 2 : 4 ( One cement : two sand : four graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) and curing complete including cost of form work in string courses copies bed plates, anchor block, plain windows sills and the like as per HPPWD. Specification 1990 volume-I ( One ) including carriage of all labour equipments and materials to various location through all leads,lifts and other incidental charges complete as per the entire satisfaction of the Engineer-in-Charge.

Providing & laying cement concrete work mechnically mixed & vibrator for compacting concrete 1 : 2 : 4 ( One cement : two approved sand : four graded crushed stone aggregate 20mm ( twenty milimeter ) nominal size ) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Suspended floors,roofs,landings & shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto all floor levels including carriage of materials within all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts and other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying cement concrete work mechnically mixed & vibrator for compacting concrete 1: 1.5 : 3 ( One cement : One & half approved sand : three graded crushed stone aggregate 20mm ( twenty milimeter ) nominal size ) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Suspended floors,roofs,landings & shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto all floor levels including carriage of materials within all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts and other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position including cost of binding wire complete upto all floor level as per HPPWD specification 1990 Volume-I ( One )including carriage of all labour equipment & materials to various location through all leads, lifts and other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Brick work second class using common burnt clay building bricks in foundation & plinth in cement mortar 1:6 ( one cement : six approved sand )as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Brick work second class using common burnt clay building bricks in Super structure above plinth level upto all floor level in cement mortar 1:6 ( one cement : six approved sand )as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Half brick work second class using common burnt clay building bricks in foundation & plinth in cement mortar 1:4 ( one cement : four approved sand ) as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Half brick work second class using common burnt clay building bricks in Super structure above plinth level upto all floor level in cement mortar 1:4 ( one cement : four approved sand ) as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Squared rubble masonry coursed with hard stone of approved quality in foundation & plinth including raking out joints in cement mortar 1 : 6 ( One cement : six sand ) as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 12mm ( Twelve milimeter ) thick prelaminated MDF board of green ply (Exterior grade) both side bwp phenol bonded grade particle board in matt finish ISI marked IS No. 12823 as per approved shade of Kitvista of Kitply or its equivelent with frame of first class deodar wood styles including fixing 5mm thick glass panel ( double glass )above lock rail including black enamelled iron butt hinges with necessary screws etc. complete as per the Architectural drawings and as per the direction of the Engineer-in-Charge as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing factory made flush doors 35mm ( thirty five milimeter ) thick commerical board i.e. Non decorative phenol bonded termite resistant & boiling water proof core of block board construction with frame of first class hard wood & well match commerical three ply veneer with vertical grain or cross band and face vaneer on both face of flush door I.S.I. marked IS No. 2202 of century ply board ( 1 ) Ltd. Or its equivalent including black enamelled M.S. butt hinges as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 19mm ( nineteen milimeter ) thick commerical board shutters for S.D.B & Duct door including fixing with nickel plated piano hinges with screws etc. complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium 100 mm ( One hundred milimeter ) floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing bright finished hard drawn hooks & eyes 250 mm ( Two hundred fifty milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing anodized powder coated aluminium sliding door bolts anodized colour and shade with bolts & nuts screws etc. complete 300 x 16 mm ( three hundred into sixteen milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing anodized powder coated aluminium sliding door bolts anodized colour and shade with bolts & nuts screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium tower bolts ( Barrel type ) anodized transparent or dyed to required shade and colour with screws etc. complete 250 x 10 mm ( Two hundred fifty into ten milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium tower bolts ( Barrel type ) anodized transparent or dyed to required shade and colour with screws etc. complete 200 x 10 mm ( Two hundred into ten milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete 125 mm ( One hundred twenty five milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete 100 mm ( One hundred milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing mild steel sliding doors bolts bright finished or / and black enamelled with nuts, screws etc. complete 250 x 16mm ( two hundred fifty into sixteen milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing oxidized mild steel tower bolts ( barrel type ) with necessary screws etc. complete 150 x 10 mm ( One hundred fifty into ten milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing oxidized mild steel handles with necessary screws etc. complete 75 mm ( Seventy five milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing steel wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G ( Eighty five G ) with wire of dia 0.56mm ( Zero pioint five six milimetre ) for doors, windows & clerestory windows of standard rolled steel section joints mitred & welded with 16 x 3.15mm ( Sixteen into three point one five milimetre ) lugs 10cm. ( ten centimeter ) Long embedded with fixing clips or with bolts and nuts as required & iron fittings complete including applying a priming coat of red lead paint & providing & fixing metal beading of approved shape & section with necessary screws complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing mild steel plain grills of required pattern in steel window frame etc. with mild steel flats 20 x 5mm ( twenty into five milimetre ) and 8 x 8 mm ( eight into eight milimetre ) Mild steel square bars in combination with or by screws distance between bars should not be more than 150 mm centre to centre total grills unit should be fixed to windows frames as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing 6 mm ( Six milimeter ) thick Aluminum Composite panel ( ACP ) tiles 60 x 60 cm ( Sixty into sixty centimetre ) flase ceiling over ready made powder coated metal sheet of approved quality of ISI marked including fixing to aluminium frames 600mm ( Six hundred milimeter ) Centre to centre Grid suspended from truss complete in all reaspect as per Architrual drawings as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Kota stone slab flooring 20mm ( Twenty milimetre ) ( Average ) thick base of cement mortar 1:4 ( One cement : four sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete 25 mm ( Twenty five milimetre ) thick as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipments and materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Kota stone slab 25mm ( Twenty five milimetre ) thick in risers of steps, skirting dado & pillars laid on 12mm ( Twelve milimetre ) ( Average ) thick cement mortar 1 : 3 ( One cement : three sand ) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipments and materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying spartic ceremic tiles 5.5 mm ( Five point five milimetre ) thick ( 300 x 300 mm size ) ( Three hundred milimetre into three hundred milimetre ) of Nitco, Kajaria / Orient etc. or equilevent of approved shade in flooring treads of steps laid on a bed of 12 mm ( Twelve milimetre ) thick cement mortar 1 : 3 ( one cement : three sand ) finished with flush pointing in white cement as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipments and materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

First class White glazed tiles 6mm ( six milimetre ) thick 20 x 30 cm ( twenty into thirty milimetre ) in skirting,risers & dedo of Nitco, Kajaria / Orient etc. or equilevent of approved shade 12 mm ( tweleve milimeter ) thick cement mortar 1:3 ( One cement : three approved sand ) & jointed with cement slurry finished with flush pointing in white cement as per HP.PWD.,specification 1990 Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing glass strips in joints of terrazo / cement concrete floor 40 mm wide & 4 mm ( Forty milimeter wide four milimeter ) thick as per the direction of the Engineer-in-Charge, including all leads, lifts & carriage of materials & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

40mm ( forty milimeter ) thick cement concrete flooring 1:2:4 ( One cement : two approved sand : four graded stone aggregte 20mm( twenty milimetre ) nominal size ) laid in one layer finished with a floating coat of neat cement in all floor level as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

50mm ( Fifty milimeter ) thick cement concrete flooring 1:2:4 ( One cement : two approved sand : four graded stone aggregte 20mm( twenty milimetre ) nominal size ) laid in one layer finished with a floating coat of neat cement in all floor level as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

15mm ( Fifteen milimeter ) thick cement plaster skirting ( upto all height ) with cement mortar 1:3 ( One cement : three sand ) finished with a floating coat of neat cement including rounding of junction with floor as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

Providing & laying marble work ( Table rubbed and polished ) in flooring 20mm ( twenty milimetre ) thick base in cement mortar 1:3 ( one cement : three approved sand ) including jointing with cement mortar 1:2 ( One cement : two marble dust ) with an admixure of pigment to match the shade of the marble. 20mm ( twenty milimetre ) thick green Baroda marble having grey streaks upto 2.05 mtrs. height as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing 0.60mm ( Zero point six zero milimeter ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 ( twenty ) microns over 5 ( Five ) microns primer coating to back coat of ployster of 5 ( five ) microns over 5 microns primer coating including fixing with prepainted iron-J or L hooks bolts and nuts 6mm dia metre with prepainted limpet & rubber washers complete with all accessories as required as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing ridge or hips 60cm ( Sixty centimetre ) overall with 0.60mm ( Zero point six zero milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coating Plus back coat of ployster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron-J or L hooks bolts & nuts 6mm ( Six milimetre ) dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing valley 60cm ( Sixty centimetre ) overall with 0.60mm ( Zero point six zero milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 ( Five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron-J or L hooks bolts & nuts 6mm ( Six milimetre ) dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing 30 cm ( thirty centimetre ) wide 30 cm ( Thirty centimeter ) deep and 90cm ( Ninety centimeter ) overall rectangular plain G.I. sheet gutter with bolts & nuts and washers etc. including making necessary connections with rain water pipes complete as per design 0.63mm ( Zero point six three milimetre ) thick as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing M.S. B.P. sheet 2mm ( Two milimetre ) thick in eaves board/facia/ soffits/ ceiling including cutting fixing & welding to steel roof mambers and applying a coat of red lead primer complete as per the instruction of the Engineer-in-Charge ( Base member of steel work shall be measured & paid for separately ) as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing on wall face PVC ( D-Plast ) rain water pipes of working pressure not less than 4.5 Kg ( Four decimal five kilogram ) per square meter including filling the joints with approved adhesive complete 150mm ( One hundred fifty milimeter ) dia pipes as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 150mm ( One hundred fifty milimetre ) dia as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing PVC Collars ISI marked approved design with steel screws and rawal plugs etc. complete 150mm ( One hundred fifty milimetre ) dia as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing mild steel holder bat clamps of approved design to P.V.C. pipes embedded in and including cement concrete block 10 x 10 x 10 cm ( Ten into ten into ten centimetre ) of 1 : 2 : 4 mix ( One cement : two sand : four graded stone aggregate 20 mm nominal size ) & cost of cutting holes & making good the wall etc. 150 mm ( One hundred fifty only ) diametre for PVC pipe as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Steel work including hollow section of BIS specification welded in built up section, trusses & framed work, including cutting,hoisting & fixing in position and applying a priming coat of red lead paint in :-

in beams, joists, channels, angles, tees, flat with connecting plates or angles cleats as in main & cross beams, hip & jack rafter,purlins connexcted to the common rafter & the like as per HPPWD., specification 1990 volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

in grating framed guards, bars, ladders,railing,brackets & similar works. as per specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing MS round holding down or anchor bolts with nuts and washers plates complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing moulded hand rail of mild steel hollow pipe 50 mm ( fifty milimetre ) dia welded in stright length over mild steel flat at top of vertical balusters including one coat of red oxide priming coat complete ( mild steel flat & baluster of railing shall be measured & paid for sepataely ) as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Mild steel Channels in doors,windows frames,manufactured from Mild steel channels section of size 75 x 40mm ( Seventy five into forty milimetre ), M.S. flat 75x4mm ( Seventy five into four milimetre ) combination as per design drawing including hinges, Jambs,beed & if required angle thrashold of mild steel angles,lugs with split end tails to each jamb including steel nuts hinges 2.5mm thick with provision of locking arrangement & shock observers & specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing angle iron cup board frames manufactured from steel iron section of 35 x 35 x 4 mm ( Thirty five into thirty five into four milimetre ) & mild steel flat 50 x 4 mm ( fifty into four milimeter ) in combination welded together to make one frame including hinges jamb,lock jamb, beed & if required angle thrashold of mild steel angle 50 x25mm ( fifty into twenty five milimetre ) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel butt hinges 2.5mm ( Two decimal five milimetre ) thick with provision of locking arrangement & shock absorber as specified & applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing angle iron cup board frames manufactured from steel iron section of 25 x 25 x 5 mm ( Twenty five into twenty five into five milimetre ) ,thickness including hinges jamb,lock jamb, beed & if required angle thrashold of mild steel angle 25 x25mm ( twenty five into twenty five milimetre ) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel butt hinges 2.5mm ( Two decimal five milimetre ) thick with provision of locking arrangement & shock absorber as specified & applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing steel glazed doors,windows & ventilators of standard rolled steel Z section with horizontial & vertical Sashbar of angle iron ( 25x25x3mm ) ( Twenty five into twenty five into three milimeter ) T-section ( 25x25x 3mm ) ( Twenty five into twenty five into three milimeter ) in fixed and openable shutters as per standard Architectural drawing,jointed mitred & welded with mild steel Channel framed or with fixing clips or with bolts & nuts as required & iron fitting, including providing & fixing of glass pans with glazing clips & special metal sesh putty of approved make complete including applying a priming coat of red lead paint as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Steel windows Fixed steel windows as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Steel windows Side hung windows as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Top Hung ventilators as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying one coat of Birla / J.K.white wall care putty/Kemocare wall smoothner putty of Kamdhenu or its equivalent over plastered surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papering smooth to give final matter finish to surface complete as per HP.PWD., specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying one coat of Acrylic primer/ Kamdhenu primer or its equivelent of superior quality on new concrete/ plastered surfaces after & including preparing the surface by thoroughly brushing the surface free from mortar drops, dust,loose materials and other foreign matter sand papering smooth the surface complete as per HP.PWD., specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Finishing wall with weather proof exterior grade premium emulsion of Kamdhenu paints/Apex Ultima or its equivelent of approved shade on undecorated wall surface ( two coats ) to give an even shade & final finish after thoroughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand papering smooth in all external plastered surfaces as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying priming coat on new concrete/masonry/asbestos cement/masonry/plastered surface surface after and including preparing the surface by thoroughly cleaning oil, grease, dirt & other foreign matter and sand papering as required Ready mixed primer as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Wall painting (two coats) with premium enamel paint Kemolite of Asian paint or its equivelent upto 140 cm ( One hundred forty centimetre ) height having two Nos. bands 5cm wide each above 125 and 135cm. ( One hundred twenty & One hundred thirty five centimetre ) Height of approved shade as per pettern to detail on undecorated cobcrete/ plastered wall surface to give shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matters etc. including sand papering smooth as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Painting two coats ( excluding priming coat ) on new steel & other metal surface with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust & other foreign matters with other then white as per HPPWD specification 1990 Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying priming coat over new wood & wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt & other foreign matter, sand papering & knotting ready mixed paint brushing primer pink as per HPPWD specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Painting two coats ( excluding priming coat ) on new wood & wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust & other foreign matter sand papering & stopping with enamel paint other than white as per HPPWD specification 1990 Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on rough side of brick/ concrete/stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:6 ( One cement : six approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on fair side of brick/ concrete/stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:6 ( One cement : six approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm (fifteen milimetre)cement plaster in single coat on fair side of brick/ concrete/ stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in (eighty milimetre) grith finished even and smooth in cement mortar 1:4(One cement:four approved sand) as per HP.PWD.,specification volume-I (one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Distempering two coats with oil bound distemper ( Tractor Synthetic washable distemper or Asian/Narolac Paints or its equivelent ) of approved shade and manufacture and of required shade on undecorated wall surface to give an even shade over and including a priming coat of distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matters and also including preparing the surface even and sand papering smooth as per HP.PWD.,specification 1990 volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing under layer for plinth protection of 75mm ( Seventy five milimetre ) thick (Unconsolidated) bed of dry/stone aggregate 40mm( forty milimetre ) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing plinth protection 50mm ( fifty milimetre ) thick in cement concrete 1 : 3 : 6 ( One cement : three sand : six graded stone aggregate 20mm nominal size ) as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Construction of cement concrete 1 : 3 : 6 ( One cement : three sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) in open surface drain with plinth protection having internal size 20 x 15 cm ( twenty into fifteen centimetre ) & with side wall of 10 cm. ( ten centimetre ) wide & inside plastering including earth work & finshed with floating coat of neat cement complete as per standard design as per HP.PWD., specification 1990 volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying in trenches, galvanised mild steel tubes ( Medium grade ) , tube fitting ( earth work in trenches to be measured & paid for separately )

15 mm ( Fifteen milimetre ) nominal bore as per HP.PWD., Specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

20 mm ( Twenty milimetre ) nominal bore as per HP.PWD., Specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm ( Twenty milimeter to forty milimeter ) nominal bore by providing & fixing tee including cutting & threading the pipes complete as per HP.PWD., Specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Fixing water metre stop cock in galvanised mild steel tube including necessary fitting such as mild steel galvanised jam nuts,sockets, etc. cutting & making long screws, complete ( Water metre & stop cock to be measured & paid for separately

15 mm ( Fifteen milimetre ) nominal bore as per HP.PWD., Specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC water storage tank of ISI 12701 marked,G.I. inlet & outlet connection,15mm nominal bore ball valve & mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level

500 ( Five hundred ) litre net capacity tank as per HP.PWD., Specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1000 ( One thousand ) litre net capacity tank as per HP.PWD., Specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Construction chamber 300mm x 300mm x 500mm ( Three hundred milimetreinto three hundred milimetre into five hundred milimetre ) inside size for stop cock with C.I. surface box 100mm x 100mm x 75mm ( one hundred milimetre into one hundred milimetre into seventy five milimetre )( inside ) with hinged cover fixed in cement concrete slab 1:2:4 ( one cement : two approved sand:four graded crushed stone aggregate 20mm nominal size ) 75mm thick foundation concrete 1:5:10 (one cement:five approved sand:ten graded crushed stone aggregate 40mm ( forty milimetre ) nominal size ) & inside plastering with cement mortar 1:3 ( One cement:three approved sand)finished with a floating coat of neat cement including curing complete, with 100mm ( one hundred milimeter )thick walls of brick masonry in cement mortar 1:5 ( One cement : five approved sand ) as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing brass full way valve with wheel 20 mm ( twenty milimeter ) nominal bore as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing G.I. / M.I. Union of following sizes ( Where not included in the items ) :-

15 mm ( fifteen milimeter ) dia as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

20 mm ( Twenty milimeter ) dia as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing plytheline- Aluminium Polyethylene ( PE-AL-PE ) composite pressure pipe U.V. stabilized with carbon black confirming to IS-15450-2004 water supply including clamps at one metre spacing, cutting, fixing & making good the wall etc. but excluding the cost of fitting ( Internal work ) pipes exposed on wall internal work-Exposed as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1216 ( One thousand two hundred sixteen ) ( 16 mm ( Sixteen milimeter ) outer dia pipe ) as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1620 ( One thousand six hundred twenty ) ( 20 mm ( twenty milimeter ) outer dia pipe ) as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PE-AL-PE- composite internal seal compression fitting as per IS-15450-2004 for hot water supply such as tees, elbows, reducers, connector, couplers & clamps with jointing testing & fixing including cutting & making good the walls etc. ( This type of fitting to be used for hot water supply only ) as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Equal Tees :-

1216 mm ( One thousand two hundred sixteen milimeter ) size as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1620 mm ( One thousand six hundred twenty milimeter ) size as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Reducing Tees:- 1620 ( One thousand six hundred twenty into all branches as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Female branch Tees :-

1216 x 1216 x 15mm ( One thousand two hundred sixteen into One thousand six hundred sixteen into fifteen milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1620 x 1620 x 20 mm ( One thousand six hundred twenty into One thousand six hundred twenty into twenty milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Female Elbows :-

1216 x 15mm ( One thousand two hundred sixteen into fifteen milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1620 x 15mm ( One thousand six hundred twenty into fifteen milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Male thread connector :-

1216 x 15mm ( One thousand two hundred sixteen into fifteen milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1620 x 15mm ( One thousand six hundred twenty into fifteen milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Female thread connector :-

1216 x 15mm ( One thousand two hundred sixteen into fifteen milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1620 x 15mm ( One thousand six hundred twenty into fifteen milimeter ) thread as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Couplers :-

1216 ( One thousand two hundred sixteen ) ( 16 mm ( Sixteen milimeter ) outer dia pipe ) as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1620 ( One thousand six hundred twenty ) ( 20 mm ( twenty milimeter ) outer dia pipe ) as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Reducers :- 1620 x 1216 ( One thousand six hundred twenty into one thousand two hundred sixteen as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete. :-

150mm (One hundred fifty milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm (One hundred ten milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC door bend with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete.

150mm (One hundred fifty milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm (One hundred ten milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete

100mm (One hundred milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC Plain bend ISI marked including fixing with approved adhesive etc. complete

100mm (One hundred milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC double equal branch with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete

150mm (One hundred fifty milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm (One hundred ten milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing mild steel clamps ISI marked including fixing with approved adhesive etc. complete

150 mm ( One hundred fifty milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

100 mm ( One hundred milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC reducer ISI marked including jointing with approved ahesive etc. complete

150mm x 110mm (One hundred fifty milimetre into one hundred ten milimeter ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm x 75mm (One hundred ten milimetre into Seventy five milimeter ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm x 90 mm dia ( One hundred ten milimeter into seventy five milimeter ) dia as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm x 75 mm dia ( One hundred ten milimeter into seventy five milimeter ) dia as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150 mm ( One hundred fifty milimeter ) dia pipe as per HPPWD.,specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge..

110 mm ( One hundred ten milimeter ) dia pipe as per HPPWD.,specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge..

75 mm ( Seventy five milimeter ) dia pipe as per HPPWD.,specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge..

Providing & fixing PVC waste pipe of ISI marked including fixing with approved adhesive complete for wash basin or sink. 32 mm ( thirty two milimeter ) dia as per HPPWD.,specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash down water closet ( Orrisa pattern ) Orrisa Pan W.C.No. 2071 size 58 x 44cm ( Fifty eight into forty four centimetre ) in white shade of Cera or its equivelent ( Earth work, bed concrete,foot rest & trap to be measured & paid for separtely ) as per HP.PWD., specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC " P " or " S " trap for water closet (Squatting pan) ISI marked including jointing the trap with the pan & PVC pipe with approved adhesive etc. complete 110mm ( One hundred ten milimetre ) dia as per HP.PWD.,specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash down water closet ( European type W.C. pan ) with intergal " P " or " S " trap including jointing the trap with soil pipe in cement mortar 1 : 1 ( One cement : one sand ) ( Seat & cover to be measured & paid for separately ) Angle Indian Universal closet of white shade of Hindware or its equilevent W.C. Pan as per HP.PWD., specification Volume -I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of Engineer-in-Charge.

Providing & fixing PTMT coloured/ white automatic flushing cistern with a pair of PVC/C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof Lid. PVC union & coupling for connections with inlet, outlet and over flow pipe including cutting holes & making good the same ( Over flow pipe to be measured & paid for separately) 5.00 Litre ( five litre ) net capacity as per HP.PWD., specification Volume -I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of Engineer-in-Charge.

Providing & fixing plastic seat ( solid/Hollow type ) & cover for wash down water closet with C.P. brass hinges & rubber buffers Solid Type white plastic seat & cover as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing vitreous China Bowl pattern Urinal including connection the Urinal with waste pipe by means of white lead mixed with chopped hemp ( waste pipe to be measured & paid for separately ) Flat back type size 430mm x 260 mm x 350 mm ( Four hundred thirty milimetre into two hundred sixty milimetre into three hundred fifty milimetre ) size as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing C.P. brass flush pipe/ Spreaders for urinal with fitting such as unions, clamps etc. ( all in C.P. brass ) including cutting holes & making good the same 15 mm ( fifteen milimetre )nominal size as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PTMT Jet spray of approved quality & colour with 1.50 ( One & five zero ) meter tube as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash basin with single hole for pillar tap with C.I. Or M.S. brackets painted white including cutting holes & making good the same but excluding fitting flat back white shade No. 102012 of clear size 580 x 400mm ( five hundred eighty into four hundred milimetre ) with pedestal of Hindware or its equivelent as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing Vitreous China Pedestal for wash basin complete recessed at the back for reception of pipes & fittings as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass Chain 50 mm ( fifty milimeter ) long & rubber plug of following size for sink or wash basin 32 mm ( thirty two milimeter ) dia as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing M.I. union for wash basin or sink 32mm ( Thirty two milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass waste for wash basin or sink 32mm ( Thirty two milimeter ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing sand grating for gully, floor trap or Nahni trap dia as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing 600mm x 450mm ( six hundred milimetre into for hundred fifty milimetre ) bevelled edge mirrior of superior glass mounted on 6mm (six milimeter ) thick A.C. sheet or plywood sheet & fixed to wooden plugs with C.P.brass screws & washers as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass Towel rain complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws 750mmx20mm ( Seven hundred fifty milimetre into twenty milimetre )as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing Toilet paper holder, C.P. brass as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing P.V.C. connection with brass union ( a ) 300 x 450 mm ( Three hundred into four hundred fifty milimeter ) length 15 mm ( fifteen milimeter ) nominal bore as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing brass bib tap ( superior or heavy type ) 15mm dia ( fifteen milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass pillar tap with capstan head 15mm dia ( fifteen milimeter ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. stop cock 15mm dia ( fifteen milimetre ) dia as as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass angle valve 15mm ( fifteen milimetre ) without nuts & pipe ( fifteen milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & laying trenches 150 mm ( One hundred fifty milimeter ) dia P.V.C. Finolex Type-B Spigot soaked waste and ventilators pipes including collers and fitting the joints with approved adhesive etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying cement concrete 1 : 4 : 8 ( One cement : four sand : eight graded stone aggregate 40 mm ( forty milimeter ) nominal size ) for surround or in caring P.V.C. pipe of 150 mm ( One hundred fifty milimeter ) dia including necessary form work etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Cutting holes through existing brick work including making good the same in cement mortar 1 : 6 ( One cement : six sand ) per centimeter depth of cutting holes upto and including 400 Sqmt ( Four hundred square centimeter ) in area as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Cutting holes upto 15 cm x 15 cm ( fifteen centimeter into fifteen centimeter ) in R.C.C. floors and roofs for passing drain pipe etc. & repairing the holes after insertion of drain pipe etc. with cement concrete 1 : 2 : 4 ( One cement : two sand : four graded stone aggregate 20 mm ( twenty milimeter ) nominal size ) including finishing complete so as to make it leak proof as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Constructing manhole with R.C.C. top slab in 1:2:4 mix ( One cement : two sand : four graded stone aggregate 20mm ( twenty milimeter ) nominal size ) foundation concrete 1:4:8 ( one cement : four sand : eight graded stone aggregate 40mm ( forty milimeter ) nominal size) inside plastering 15mm ( fifteen milimeter ) thick with cement mortar 1:3 (One cement : three sand ) finished with a floating coat of neat cement & making channels in concrete 1:2:4 mix ( One cement : two sand : four graded stone aggregate 20 mm ( twenty milimeter ) nominal size ) finished smooth complete including curing & testing inside size 800 x 800 x 500 mm ( eight hundred into eight hundred into five hundred milimeter deep including precast R.C.C. cover with 230 mm ( Two hundred thirty milimeter )thick wall of brick masonry using common burnt clay building bricks in cement mortar 1:3 ( one cement : three sand ) as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Supplying & fixing 450 x 600 mm ( Four hundred fifty into six hundred milimeter ) precast R.C.C. cover without frame of heavy duty as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing precast RCC cover with frame for 300 x 300 mm ( three hundred into three hundred milimeter ) internal diamension of gully trap complete as per HP.PWD., specification of 1990 volume-I including carriage of materials, labour, tools and plants through all mode of transportation within all leads, lifts and as per direction of the Engineer-in-Charge.

Supplying & filling brick bats in dispension trenches complete in all respect as per HP.PWD., specification of 1990 volume-I including carriage of materials, labour, tools and plants through all mode of transportation within all leads, lifts and as per direction of the Engineer-in-Charge.

Providing & fixing PVC bend of required degreee, Plain bend 75 mm ( seventy five milimeter ) dia as per HP.PWD., specification of 1990 volume-I including carriage of materials, labour, tools and plants through all mode of transportation within all leads, lifts and as per direction of the Engineer-in-Charge.

Providing weep holes in brick masonry/ stone masonry/plain/reinforced concrete abutment, wing wall,return wall with 100mm dia PVC pipe extending through the full width of the structures with slope of 1 ( V ) : 20 ( H ) towards drawing face complete as per drawing and technical specification clause 614, 709,1204.3.7 as per HP.PWD., specification of 1990 volume-I including carriage of materials, labour, tools and plants through all mode of transportation within all leads, lifts and as per direction of the Engineer-in-Charge.

Providing & laying of interlocking concrete block pavement having thickness 60 mm ( sixty milimeter ) as per drawing & Technical Specification clause 1504 as per HP.PWD., specification of 1990 volume-I including carriage of materials, labour, tools and plants through all mode of transportation within all leads, lifts and as per direction of the Engineer-in-Charge.

Lal Singh Chauhan Contractor

Rakesh Chaudhary