CA NO. GE/K-50/2025-26 - SPL REPAIR TO BLDG NO T-66 OF 15 JAK RIF, BLDG NO T-24 OF 56 MTN BE CAMP AND T-23 OF 259 TRANSIT CAMP (BTC) AT DRAS UNDER GE KARGIL

Amount

Dismantling of plain corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed by the Engg-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engg-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engg-in-Charge.

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc and fixed with L-type or J-type or cranked hook bolts in lieu of screw complete all as specified and directed by the Engg-in-Charge.

M&L for preparing old steel surfaces of any description over 10cm width/girth and applying one coats of synthetic enamel paint complete all as specified and directed by the Engg-in-Charge.

Demolition of Cement Concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below or above ground level) complete all as specified and directed by the Engg-in-Charge.

M&L for 25mm thick PCC type B-1, 1:2:4 (20 mm graded aggregate) as in sub base of floors or similar works complete all as specified and directed by the Engg-in-Charge.

M&L for 75mm thick PCC type C-2, 1:3:6 (40mm graded agg) as in plinth protection and sub base or similar works complete all as specified and directed by the Engg-in-Charge.

M&L for PCC 1:4:8, type D-2 (using 40mm graded stone agg) in foundation, filling and mass concrete etc complete all as specified and directed by the Engg-in-Charge.

M&L for coloured chequered cement concrete tiles 300x300x25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors including 20 mm thick screed bed in CM (1:4) complete all as specified and directed by the Engg-in-Charge.

Demoliton of stone/ boulder masonry, precast concrete articles and precast concrete block walling including all quoins, arches, pillars, etc built in cement mortar of any description not other specifically provided for etc complete all as specified and directed by the Engg-in-Charge.

M&L for Walling of random rubble masonary, uncoursed well bonded, bedded and solidly hearted, bulit in cement mortar 1:4 complete all as specified and as directed by Engr-in-Charge

M&L for precast cement concrete type C1 (1:3:6) (using 20mm graded crushed stone agg) block masonary with solid blocks exc 10cm in width and setting in CM 1:4 complete all as specified and directed by Engr-in-charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed by the Engg-in-Charge.

M&L for machine cut Kota stone slab flooring 20-25mm thick, over cement screed bed or bedding layer of cement mortar 20 mm thick in CM for laying floor finishes base laid and jointed with grey cement slurry mixed pigment to match the shade of the slab including rubbing and mirror polishing preparation complete all as specified and directed by the Engg-in-Charge.

M&L for 18 to 20mm thick granite work (table rubbed and polished) Black colour to shelves, counter slabs & skirting etc over and including 15mm thick screed/ rendering in CM (1:4) and pointing with white cement (mixed with suitable colour) (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding edges of granite complete all as specified and directed by the Engg-in-Charge.

Dismantiling of floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by the Engg-in-Charge.

M&L Non skid Ceramic coloured tiles 600x600x7 to 8mm thick area of each tiles exc 0.18 sqm but not exc 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 complete all as specified and directed by the Engg-in-Charge.

M&L Non skid Ceramic coloured tiles 300x300x7 to 8mm thick area of each tiles exc 0.06 sqm but not exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 complete all as specified and directed by the Engg-in-Charge.

M&L for coloured glazed ceramic tiles in vertical surfaces 450x300mmx7mm thick Set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over 15mm thick rendering in CM 1:4 complete all as specified and directed by the Engg-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/blankets, any thickness, including cover fillets complete all as specified and directed by the Engg-in-Charge.

S&F 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails on wall to timber frame work complete all as specified and directed by the Engg-in-Charge.

S&F 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails on ceiling to timber frame work complete all as specified and directed by the Engg-in-Charge.

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on solid PVC wall lining, Insulated PVC wall lining, and solid PVC partitions inclusive of Solvent cement and fixing at site complete all as specified and directed by the Engg-in-Charge.

Dismantling timber scantlings as in fillets, rails, posts, rafters, purlins, etc under 40 Sqcm in framed work, in any position complete all as specified and directed by the Engg-in-Charge.

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm in square, rectangular or traingular in section, clean sawn secured with nails or brads complete all as specified and directed by the Engg-in-Charge.

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 3 Sqcm but not exceeding 6 Sqcm in square, rectangular or traingular in section, bullnosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed by the Engg-in-Charge.

M&L for Plain fillets of second class soft wood (KAIL), sectional area not exceeding 3 Sqcm in square, rectangular or traingular in section, bullnosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed by the Engg-in-Charge.

Taking down chowkats or frames not exc 1.5 Sqm with shutters (without taking off shutters from the frames) each complete all as specified and directed by the Engg-in-Charge.

Taking down chowkats or frames exc 1.5 Sqm but n.exc 4.0 Sqm with shutters (without taking off shutters from the frames) each complete all as specified and directed by the Engg-in-Charge.

S&F 2nd class soft wood plain, solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by the Engg-in-Charge.

S&F 30 mm thick 2nd class soft wood (KAIL) plain framed panelled shutter (any number of panels) with panels of timber flat on both sides (Feather edge) or of veneered particle board medium density wood particle board with commercial face veneers and fitted to chowkhat.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks, or galvanised wire staples including etc complete all as specified.

Hacking out old broken glass (any thickness,size,quality or description) from wooden frames metal frames or stone,concrete or brick surrounds,glazed with putty or fixed with beads complete all as specified and directed by the Engg-in-Charge.

S&F 3mm thick glass pan ordinary quality and glazing fixed with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and directed by the Engg-in-Charge.

S&F 150mm long Aluminium anodisedl barrel tower bolt of extruded section and fixed with screw or welded complete all as specified and directed by the Engg-in-Charge.

S&F 100mm mild steel butt hinges medium weight, cold rolled fixed with screw or welded complete all as specified and directed by the Engg-in-Charge.

S&F 125mm extruded aluminium alloy handles febricated type anodised fixed with screws or welded complete all as specified and directed by the Engg-in-Charge.

S&F 300mm Aluminium alloy, anodised,sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by the Engg-in-Charge.

S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate fixed with screw or welded complete all as specified and directed by the Engg-in-Charge.

S&F in repair curtain rails anodised aluminium plated with fixing bracketes, stops, rollers etc complete all as specified and directed by the Engg-in-Charge.

M&L for preparation of New surface of wood and wood based material surface of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by the Engg-in-Charge.

M&L for preparation of old surface of wood and wood based material surface of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed by the Engg-in-Charge.

Dismantling of PVC drain pipes of any size or any dia and any position/ description, including disposal or removing to store complete all as specified and directed by the Engg-in-Charge.

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by the Engg-in-Charge.

S&F PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by the Engg-in-Charge.

Taking up or down 20 mm dia steel tubing/PPR connections, including cleaning for refixing or removal to store complete all as specified and directed by the Engg-in-Charge.

S&F 20mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed to wall/ceiling or laid in floors complete all as specified and directed by the Engg-in-Charge.

Taking up or down 25 mm dia steel tubing/PPR connections, including cleaning for refixing or removal to store complete all as specified and directed by the Engg-in-Charge.

S&F 25mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed to wall/ceiling or laid in floors complete all as specified and directed by the Engg-in-Charge.

S & F in repairs vitreous china squatting pan, 'Orissa pattern, size 580x440 mm whinte, with 'P' or 'S' trap including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe or integral foot rests (excluding flushing cistern and flush pipe) complete all as specified.

S&F in repairs 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with handle, PVC bend including connecting to WC and fixing on walls with bracket complete all as specified and directed by the Engg-in-Charge.

S&F in repairs vitreous china wash hand basin (flat back) white of size 550x400mm with pedestal pattern including waste coupling & waste pipe and a pair of mild steel angle iron brackets of suitable size complete all as specified and directed by the Engg-in-Charge.

S&F in repair 15mm bore PVC connection 600mm long both ends screwed with brass cap complete all as specified and directed by the Engg-in-Charge.

S&F in repair 20mm bore Pillar taps of cast copper alloy, with capstan heads, chromium plate, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nut screwed for iron pipe and fixed complete all as specified and directed by the Engg-in-Charge.

S&F in repair 20 mm dia chromium plated fancy type Bip tap with round handle screwed down for iron pipe or brass ferrule complete all as specified and directed by the Engg-in-Charge.

S&F in repair 20 mm dia chromium plated fancy type stop valves/ angle cock screwed down high pressure, screwed for iron pipe complete all as specified and directed by the Engg-in-Charge.

S&F in repair 25dia PPR Gate valves (brass insert) as per requirement of the site complete all as specified and directed by the Engg-in-Charge.

S&F in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size 915 mm X 460 mm & bowl size 410x330x160 mm including sink coupling and waste pipe complete all as specified and directed by the Engg-in-Charge.

Dismantling PVC water tanks of capacity exc 500 ltr but n exc 1000 ltr and removing to store complete all as specified and directed by the Engg-in-Charge.

S&F 1000 ltr capacity rotationally moulded polythene water storage tanks (cylindrical vertical with closed top) multilayers of approved make hoisted & fixed in position complete all as specified and directed by the Engg-in-Charge.

M&L for 75mm thick cement concrete type C-1 (1:3:6) using 20mm graded agg as in copings slightly rounded or chamfered angles and throating complete all as specified and directed by the Engg-in-Charge.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses built in CM 1:4 complete all as specified and as directed by Engr-in-Charge

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by the Engg-in-Charge.

M&L for rendering 15mm thick in CM (1:4) finished even & smooth without using extra cement on brick/concrete surfaces complete all as specified and directed by the Engg-in-Charge.

M&L rendering 15mm thick in CM (1:6) finished even & smooth without using extra cement on brick/concrete surfaces complete all as specified and directed by the Engg-in-Charge.

M&L for two coats of cement based paint on newly plastered surfaces of walls over a coat of primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of OBD over a coat of 1mm thick putty complete all as specified and directed by the Engg-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by the Engg-in-Charge.

S&F Roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by the Engg-in-Charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by the Engg-in-Charge.

M&L for preparing old steel surfaces of any description over 10cm width/girth and applying two coats of synthetic enamel paint complete all as specified and directed by the Engg-in-Charge.

S&F 9-10 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination fixed with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc as in aluminium frame work including cleat angle, Aluminium snap beading for glazing/ paneling, C.P brass/ stainless steel screws complete all as specified and directed by the Engg-in-Charge.

Taking down of shutters exc 1.0 Sqm but n.exc 2.0 Sqm each complete all as specified and directed by the Engg-in-Charge.

S&F 30mm thick 2nd class softwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc, sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by the Engg-in-Charge.

S&F 5.5mm thick glass pan ordinary quality and glazing with rubber strip in square exc 0.5 Sqm in each pane complete all as specified and directed by the Engg-in-Charge.

S&F 100 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed by the Engg-in-Charge.

S&F 75mm mild steel butt hinges medium weight, cold rolled fixed with screws or welded complete all as specified and as directed by Engr-in-Charge

S&F 100mm extruded aluminium alloy handles fabricated type anodised fixed with screws or welded complete all as specified and directed by the Engg-in-Charge.

S&F in repairs of Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc.

M&L for Point wiring for light/fan/bell with FRLS cable of 1.5sqmm PVC insulated (red/blue/yellow for phase, black for neutral and green for earth) unsheathed multistranded copper conductor 1100 volts grade in and including not less than 2mm thick PVC casing caping with all accessories and 1.5sqmm green in colour PVC insulated multistranded copper conductor FRLS cable for earth continuity connected to common earth dolly incl MS/GI sunken box with 3mm thick pre laminated hylum sheet/PVC box with back plate,flush/surface type for mounting fittings such as switches,socket,and regulator complete all as specified and directed. (a) One light point or bell/buzzer point controlled by one switch.

All as per Srl item No 84 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 5 Amps on independent board complete all as specified and directed by the Engg-in-Charge.

All as per Srl item No 84 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 15 Amps on independent board complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of Switch piano flush type 5 Amps, single pole one way complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps flush type complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of Switch socket combination 2 in 1,3 pin, 5 and 15 Amps flush type complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of in Ceiling rose on PVC Square Block surface bakelite 65x50mm, two to three terminals complete all as specified and directed by the Engg-in-Charge.

S&F in repair LED white colour 18 Watt, 220V, AC Decorative ultra slim square profile tubelight fitting with extruded polycarbonate, environmental friendly, energy efficient ready to use incl connecting up with two/three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by the Engg-in-Charge.

S&F in repair Lamp holder, PVC/Polycarbonate type on square block with back plate suitable for batten fittings complete all as specified and directed by the Engg-in-Charge.

S&F in replacement LED bulb 09 watt, 230 volts complete all as specified and directed by the Engg-in-Charge.

S&F in replacement Sheet metal enclosure for DB's Double door, single pole and neutral, 240V, 12 way with 200 Amp rated bus bar including blanking plates where required complete all as specified and directed by the Engg-in-Charge.

S&F in replacement 240V, 10 KA C curve MCB, SPN 40 to 63 Amp fixed in existing DB incl connecting testing and commissioning complete all as specified and directed by the Engg-in-Charge.

S&F in replacement 240V, 10 KA C curve MCB, SP 5 to 32 Amp fixed in existing DB incl connecting testing and commissioning complete all as specified and directed by the Engg-in-Charge.

S&F in replacement LED light fitting 9W/10W bulkhead luminaries incl LED light driver holder connecting up three core flexible copper conductor cable of suitable size complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of LED Flood light fitting, 70watt, 7000 k green/natural white, IP>66, grey powder coated die cast aluminium housing with inbuilt energy efficent surge protected electronic driver with all connected accessories complete all as specified and directed by the Engg-in-Charge.

S&F in replacement round shape 12W, 220 volts, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size and cutting of hole in ceiling as required complete all as specified and directed by the Engg-in-Charge.

S&F in replacement exhaust fan, steel body, AC single phase, 230 V of size 380mm sweep with blades and frame and louvers complete incl cutting of suitable size of hole on wall with all connected accessories and making surface good after fixing complete all as specified and directed by the Engg-in-Charge.

M&L for submain wiring comprising single core, 2 Runs of 6sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including min 25mm dia. PVC Casing Caping ISI Marked(heavy duty) and its fittings on surface/recessed complete including provision of 1X6.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS complete all as specified and directed by Engr-In-charge. Note :- Extra length of cables/ wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly.

S&F in replcement 1100 volts grade heavy duty 16 sqmm 2 core, flat cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended with suitable size of PVC conduit and saddle for whole length to fix on wall/surface complete all as specified and directed by the Engg-in-Charge.

M&L in repair for Earthing complete with galvanised steel earth plate electrode of size 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to and including GI iron wire of size 4 mm dia by means of GI bolts, nuts, check nuts and washers, protected by 15mm bore GI light grade ISI marked pipe upto and including test points. Earth plate shall be surrounded by alternate layer 15cm thick of charcoal or coke and common salt all around bottom and top, 20mm bore GI medium grade ISI marked pipe for watering and including funnel,wire mesh,PCC chamber pit made with PCC(1:3:6) type C-1(using 20mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50M, CI pit cover duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No.3 of SSR 2009(Part-I) and all as directed. Note:- (i) Protection pipe and earthing strip upto test point from top of the earth plate and further upto the body of electrical equipment shall be included in the unit rate of this item. (ii) Earth testing arrangement should be done by contractor as per direction of Engr-In-Charge.

S&F in replacement Sheet metal enclosure for DB's Double door, single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required complete all as specified and directed by the Engg-in-Charge.

M&L in repair LT cable 2core, 16 sqmm 1100 Volts, XLPE insulated armored, heavy duty with aluminium conductor laid in trenches or fixed to walls/poles or passing through pipes incl cable gland lugs/ thimbles/ ferrules including connecting, testing and commissioning at site complete all as specified and directed by the Engg-in-Charge. Notes:- Excavation, RFR and protection pipe etc shall be measured and paid separately under relevant item of schedule

Excavation in trenches nexc 1.5m wide and nexc 1.5m in depth for foundation or for shafts, wells, cesspits, manholes, pier holes, not exceeding 10 sqm on plan and not exceeding 1.5Mtr in depth & getting out of Hard/Dense soil for laying of cable complete all as specified and directed by the Engg-in-Charge.

Removal of excavated soil to distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by the Engg-in-Charge.

Returning filling, including spreading, levelling, watering and well remming in layers not exceeding 25cm thick complete all as specified.

Supply and laying in replacement of double wall corrugated HDPE (DWC) pipe of size DN 40, pressure rating SN-8, in trenches for protection of cable complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of GI tubing light grade 40 mm bore as in cable protection fixed to poles/walls or laid in trenches/under road crossing etc complete all as specified and directed by the Engg-in-Charge.

Note : Deduction for amount of Rs. 1,19,890.60 as listed in Schedule 'A' Part-II (Schedule of Credit) shall be made while awarding of contract.

M/S ALI MOHD AND SONS (BID ID -3376521)

KASHMIR FAIR DEAL SERVICES (BID ID -3376488)

HARMEET TRADERS (BID ID -3375913)

M/S DUTTA ENGINEERING WORKS (BID ID -3376503)

M/S GORIA CONSTRUCTION CO (BID ID -3376429)

M/s Ashok Kumar (BID ID -3375958)

M/S BALI CONSTRUCTIONS (BID ID -3376006)