Construction of Additional Alteration in Govt. High School at Kandi in Distt Kangra (HP) (Deposit Work) (SH-Construction of 2 Nos Class room including boundary wall etc)

Amount

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs (Three meters) clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation footings, bases of columns and mass concrete as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etc; including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including mouldings, cornices etcetera; including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders lintels window sills, cornices, arches corbelling including curved surfaces where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in work in edge of slab and breaks in floors and walls under any thickness as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete 1:6:12 (One cement; Six sand; Twelve graded broken/crushed stone aggregate 40mm (Forty milimetres) nominal size) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth, as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete work 1:2:4 (One Cement : Two Sand : Fopur graded stone aggregate 20 mm (Twenty millimetres) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like mass concrete etc; including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete work 1:2:4 (One Cement : Two Sand : Fopur graded stone aggregate 20 mm (Twenty millimetres) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves their supports balconies, beams, girder, bressumers and cantilevers, including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete work 1:2:4 (One Cement : Two Sand : Fopur graded stone aggregate 20 mm (Twenty millimetres) nominal size) and curing complete, excluding cost of form work and reinforcement for reinforced concrete work in in Columns, pillars posts and struts for all floors heights and the like including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing Tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position complete including cost of binding wires complete and other incidentals due for its completion for all floors, including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Second class brick masonry using common burnt clay building bricks in super-structure upto any floor level in cement mortar 1:6 (One cement: Six sand) including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints with cement mortar 1:5 (One cement : Five sand) and curing complete including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : Six sand : Twelve graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) at plinth level in cement mortar 1:6 (One cement: Six sand) including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Half second class brick masonry in common burnt clay building bricks in cement mortar 1:4 (One cement : Four sand) complete and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals .

Boulder filling dry hand packed tightly under floor complete including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 40mm (forty millimetres) thick second class deodar wood, panelled glazed or panelled and glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws, including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 300x16mm size (Three hundred into sixteen milimetres) anodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. completed including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 250x10mm (Two hundred fifty into Ten milimetres) size aluminium Tower bolts (Barrel type) anodized transparent or dyed to required colour and shade with necessary screws etc; including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred milimetres) size aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc; including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred milimetres) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing plain M.S. grills of required pattern in steel frames of windows etc with M. S flat, square or round bars with round hooks complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 40 mm (Forty millimetres) wide and 4 mm (Four millimetres) thickglass strips in joints of cement concrete floors complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing 40mm (Forty milimetres) thick cement concrete flooring thick cement concrete 1:2:4 (One cement : Two sand: Four graded crushed stone aggregate 20mm (twenty milimetres) nominal size laid in one layer finished with a floating coat of neat cement complete upto all floor level, complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Extra for making chequers of approved pattern on cement concrete floors. steps. landings and pavements etc; complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

15mm (Fifteen millimetres) thick cement plaster skirting (upto any hieght) with cement morter 1:3 (One cement : Three sand) finished with a floating coat of neat cement including rounding of junction with floor, complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing standard steel section of ISLC and flat iron doors, windows, clerestory windows frame manufactured from ISLC iron section of 75x40mm (Seventy five into Forty millimetres), thickness with M.S. flat iron section 75x4mm (Seventy five into Four millimetres) thick including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 50x25mm (Fifty into Twenty five milimetres) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two point Five millimetres) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing standard steel section of M.S. angle and flat iron doors, windows, clerestory windows frame manufactured from M.S. angle iron section of 40x40x5mm (Forty into forty into five millimetres) thickness 50x5mm (Fifty into five millimetres) thick with M.S. flat iron section 75x4mm (Seventy five into four millimetres) thick including hinges jamb, lock jamb, beed and if required angle thrashold of mild steel angle 50x25mm (Fifty into Twenty five milimetres) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two point Five millimetres) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing steel glazed framed shutter of Z-section with 4mm (Four millimetres) thick glass pan with putty for doors, windows, clearstory windows required shape and section with fitting and necessary screws including applying a priming coat of red lead paint complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing steel wire gauge windows and ventilators of stadand rolled steel sections, joints mitred and welded with windows frames including rawl plug and steel screws as required and oiron fitting including galvanised M.S. wire gauge destination 85-G with wire of dia 0.56 mm (Zero point five six millimetres) for doors windows and clerestorey windows including mettaled beading with necessary screws necessary including applying a priming coat of red lead paint complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S. fan clamps of type-I of 16mm(Sixteen milimetres) diameters M.S. bar bent to shape with hooked ends to Reinforced Cement Concrete slab during laying including painting the exposed portion of loop all as per standard design complete including applying a priming coat of red lead paint complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 90cm (Ninety centimetres) height railing with M.S. rectangulr hollow pipe 75x50mm (Seventy five into fifty milimetres) of 14 gauge M.S. black shaeet make hand raail and M.S. square br 20mm (Twenty millimetres) size ballusters at 30cm (Thirty centimetres) centre to cemntre duly welded with 2 Nos. M.S. flat 40x6mm (Forty into six milimetres) size and 20mm (Twenty millimetres) M.S. square bars lugs 10cm (Ten centimetres) long at lower end of ballusters embedded in RCC steps of waist slab including priming coat of steel primer and painting with steel enamel paint other than white complete including applying a priming coat of red lead paint complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel & other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome complete including applying a priming coat of red lead paint complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter enamel paint other than white complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat)on new wood and wood based surfaces, with ready mixed paint, brushing to give an even shade including cleaning of all dirt, dust and other foreign matter sand papering and stopping ready mixed paint other then white, complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

6mm (Six millimetres) thick cement plasters in ceiling with cement mortar 1:4 (one cement: Four sand) for all heights complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: six sand) complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

White washing with lime on ceiling and/or sloping roofs surfaces two coats to give an even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete, complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing plinth protection 50mm (Fifty milimetres) thick cement concrete 1:3:6 (One cement: Three sand: Six graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) including finishing the top surfaces of concrete smooth complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (Seventy five milimetres) thick(un-consolidated)bed of dry brick/stone aggregate 40mm (Forty milimetres) nominal sizes well rammed and consolidated and grouted with fine sand including preparation of ground complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Construction course rubble hammer dressed ‘U’ shape open surfaces drain with side wall 15x22cm (Fifteen into twenty two centimetres) in cement mortar 1:6 (One cement : Six sand) and inside plastering with cement plaster 1:3 (One cement : Three sand) including earth work and laying 10cm cement concreter in 1:5:10 (One cement: Five sand: Ten graded) crushed stone aggregate 40mm (Forty millimetres) nominal size and 7.5 cm (Seven point five centimetres) cement concrete 1:2:4 (One cement: Two sand: Four graded) crushed stone aggregate 20mm (Twenty millimetres) nominal size and finished with a floating cost of neat cement complete as per standard design complete in all respect complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

ASHISH KUMAR GOVT CONTRACTOR