GEAF/AMB-T-53/2025-26

Amount

Taking down carefully any type of battens or conduit point wiring with or without conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing surface complete all as specified and directed.

M&L for point wiring with PVC insulated and unsheathed cable 1.5 Sqmm (nominal area) ISI marked multi-stranded copper conductor FRLS single core including suitable size of PVC casing & caping, concealed terminal boxes not less than 1.6 mm thick of required size with top cover 2.8 mm thick of plastic laminated sheet (Hylum) of required colour complete metal flush terminal boxes with all accessories including 1.5 Sq mm PVC insulated and unsheathed stranded copper wire conductor cable to common earth and connecting to earth dolly including colour coding of cable shall be Phase - Red, Neutral- Black and Earth- Green complete all as specified and directed for:- Note:- (i) Rate of cutting chasing,Pinning in & making good shall quoted in unit rates.

One light/fan point controlled by one, one way switches

One bell point controlled by push button on same board with other switches.

One socket outlet point 3 pin 5 Amps on the same board.

One socket outlet point 3 pin 5 Amps on independent board.

M&L for point wiring with PVC insulated and unsheathed cable 2.5 Sqmm (nominal area) ISI marked multi-stranded copper conductor FRLS single core including suitable size of PVC casing & caping, concealed terminal boxes not less than 1.6 mm thick of required size with top cover 3 mm thick of plastic laminated sheet (Hylum) of required colour complete metal flush terminal boxes with all accessories including 2.5 Sq mm PVC insulated and unsheathed stranded copper wire conductor cable to common earth and connecting to earth dolly including colour coding of cable shall be Phase - Red, Neutral- Black and Earth- Green for 15 Amps socket outlet complete all as specified and directed Note:- (i) Rate of cutting chasing,Pinning in & making good shall quoted in unit rates.

S&F in repair switch piano, flush type, 05 / 06 Amps, single pole, one way, 240 volts complete all as specified & directed

S&F in repair switch piano, flush type, 15 / 16 Amps, single pole, one way, 240 volts complete all as specified & directed

S&F in repair socket outlet 3 pin, 05 / 06 Amps, flush type, 240 volts complete all as specified & directed.

S&F in repair for socket outlet flush type 3 pin , 15/16 Amps complete all as specified and directed.

S&F in repair bell push flush type switch, 5 Amp complete all as specified and directed by Engr-in-charge.

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed

S&F in repair 2.5 mfd capacitor suitable for ceiling fan complete all as specified and directed

S&F in repair 3.15 mfd capacitor suitable for exhaust fan complete all as specified and directed

M&L for point wiring with PVC insulated and unsheathed cable 1.5 Sqmm (nominal area) ISI marked multi-stranded copper conductor FRLS single core including 20mm dia medium grade PVC conduit concealed in wall / false ceiling, concealed metal flush boxes, including white cover plates with frame for fixing of modular switches/sockets etc with all accessories including 1.5 Sq mm PVC insulated and unsheathed stranded copper wire conductor cable to common earth and connecting to earth dolly including colour coding of cable shall be Phase - Red, Neutral- Black and Earth- Green complete all as specified and directed by Engr-in-charge for:- Note:- (i) Rate of cutting chasing,Pinning in & making good shall quoted in unit rates.

One light/fan point/Exhaust fan controlled by one, one way switch 6 amps, complete all as specified and directed

One bell point controlled by push button on the same board with other switch or independent, complete all as specified and directed

One 5 pin, 5 Amp switch socket out let on the same board with other switches, complete all as specified and directed

One 5 pin, 5 Amp switch socket out let on the independent board., complete all as specified and directed

M&L for point wiring with PVC insulated and unsheathed cable 2.5 Sqmm (Nominal area) stranded copper conductor single core including ISI marked 20 mm dia medium grade PVC conduit for point wiring, concealed in wall / metal flush boxes including white cover plates and frame for mounting switch/socket (modular) with all accessories including 2.5 Sqmm PVC insulated and unsheathed stranded copper wire conductor cable to common earth and connecting to earth dolly for one 5 pin, 15 Amps switch socket out let point on an independent board including colour coding of cable shall be Phase- Red, Neutral- Black and Earth- Green complete all as specified and directed by Engr-in-charge. Note:- (i) Rate of cutting chasing,Pinning in & making good shall quoted in unit rates..

S&F in repair modular switch flush type, 6 Amps, single pole, one way 1 module complete all as specified and directed

S&F in repair modular switch flush type, 16 Amps, single pole, one way 1 module complete all as specified and directed

S&F in repair modular socket , 3 pin, 6 Amps, multipurpose 2 module complete all as specified and directed.

S&F in repair modular socket , 3 pin, 16 Amps, multipurpose 2 module complete all as specified and directed.

S&F in repair ceiling rose, surface bakelite, size as per relevant IS, three terminals complete all as specified and directed.

S&F in repair modular fan step regulator 120W 2 module complete all as specified and directed.

S&F in repair modular bell push switch complete all as specified and directed by Engr-in-charge.

S&F in repair Buzzer, Ding Dong AC 230volts complete all as specified and directed by Engr-in-charge.

S&F in repair lamp holder,insulated body, with back PVC rectangular block for fixing of holder with screw complete all as specified and directed.

S&F modular cover plate with frame for 3 module complete all as specified and directed

S&F modular cover plate with frame for 4 module complete all as specified and directed

S&F modular cover plate with frame for 6 module complete all as specified and directed

S&F modular cover plate with frame for 8 module complete all as specified and directed.

S&f modular metal flush box 3 module complete all as specified and directed.

S&f modular metal flush box 4 module complete all as specified and directed.

S&F modular metal flush box 6 module complete all as specified and directed

S&F modular metal flush box 8 module complete all as specified and directed

M&L for Point Wiring using approved colour coding as per IS with Zerohalogen flame redardant (ZHFR) smoke free non toxic non corrosive with copper cable 1.5 sqmm (nominal area) single core insulated and unsheathed stranded cable 1100 Volts grade and including (ERW) stove enamelled concealed conduit heavy duty ISI marked complete all as specified and directed for one light point controlled by one way switch complete all as specified and directed. Note:- (i) Rate of cutting chasing,Pinning in & making good shall quoted in unit rates.

S&F in repair Switch flame proof rotary type with termination box in LM6,16A ,single pole 250 V complete all as specified and directed.

S&F in repair flame proof switch socket & plug combined in LM6 cable termination box in LM6 ,16 A 250V ,2P+ earth complete all as specified and directed.

S&F in repair LED light fitting 2x16 Watt flameproof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed

Taking down of MCB DB with MCB 's and making good disturbed surfaces of wall complete all as specified and directed

S&F double door VTPN 4 way suitable for 4 pole MCCB as incoming & SP/TP MCB as outgoing, 200 Amps rated busbar, inter connection link, cable ties, earth bar etc complete all as specified and directed.

S&F double door MCB DB sheet metal enclosure single pole and neutral 240V with 200 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 4 way complete all as specified and directed.

S&F double door MCB DB sheet metal enclosure single pole and neutral 240V with 200 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 8 way complete all as specified and directed.

S&F in repair MCB, TPN 25 To 63 Amp, 415V 10KA 'C' curve miniature circuit breaker (MCB) 16 KA to be fixed in the DB complete with connection testing and commissioning complete all as specified and directed.

S&F in repair MCB, single pole & neutral, 240 Volts (16 to 32) Amps,10 KA complete all as specified and directed.

S&F in repair MCB, single pole, 240 Volts (05 to 32) Amps,10 KA complete all as specified and directed .

Taking down light fitting any description complete all as specified and directed .

S&F LED lights fitting 1x 20W, 220V, worm white AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed/ Surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed

S&F round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S & F LED light fitting 1x9W/1X10Wbulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed

Taking down fan, dismantling blades and removing fan and blades to store, complete all as specified and directed

Hanging only ceiling fan after repair and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and directed

M&L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. complete all as specified and directed

Ceiling fan 1200 /1400 mm sweep

Exhaust fan 300 mm sweep

Exhaust fan 450 mm sweep

Wall mounted/pedestal fans 400 mm /450mm sweep

S&F in repair metal bush bearing made out of gun metal/brass of same size suitable for ceiling fans,wall mounted fan and exhaust fans complete all as specified and directed.

S&F in repair ball bearing suitable Ceiling fan 1200 /1400 mm sweep, complete all as specified and directed

S&F in repair ball bearing suitable Exhaust fan 300 mm sweep, complete all as specified and directed

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM five star rated with brushless direct current motor (BLDC)complete all as specified and as directed

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed

S & F in repair Heating element (round/ triangular) of size 1.5KW, complete all as specified and directed

S & F in repair Thermostat for 25 ltrs capacity geyser., complete all as specified and directed

S & F in repair Rubber Gasket for Inner Tank 25 Ltrs Capacity, complete all as specified and directed

S & F in repair Air release Valve for 25 Ltrs capacity, complete all as specified and directed

S & F in repair Fusible lead nut for safety pressure of existing type.

S & F in repair Indicator Lamps for Geyser.

S & F in repair PVC connections 15 mm size with PTMT nuts of up to length 600 mm length (for hot and cold water inlet and outlet ) complete all as specified and directed

Attending compliant for Comprehensive maintainance and servicing of refrigerator / deep freezer of capacity 165 to 310litres including labour for detecting the leakage of gas ,repairing leakage and recharging refrigerant, cleaning of cooling coil, condenser, compressors, with vacuum cleaner and cleaning solution, checking servicibility of electrical / electronic circuits relays, wiring kit, thermostat switches, knobs, etc. and keeping the units in satisfactory working conditions complete all as specified and as directed. Note: (a) Spares / parts / componenets/ refrigerant gas will be measured and paid separately under relevant items hereinafter and labour charges for replacement shall be deemed to be included in this unit rate quoted

S & F in repair thermostat switch with knob, complete all as specified and directed

S & F in repair starting relay 1/8HP to 1/6HP with OLP , complete all as specified and directed

S & F in repair copper filter, single capillary, pencil type, complete all as specified and directed

Attending compliant for Comprehensive maintainance and servicing of water cooler cooling cap 40 litre/storage cap 80 litre cleaning of cooling/condensing coil, oiling of condenser fan motor, cleaning of drain pipe testing for smooth functioning complete all as specified and directed.

All as per BOQ srl item No. 85.00 here-in-above but capacity 150 Ltr, complete all as specified and directed

Detection of refrigerent leakage from water cooler cooling cap 40 litre, repair of cooling coil/condensing coil for minor leakage if any flushing of system and gas charging in the system up to required qty, and sealing / brazing/soldering complete all as specified and directed

Detection of refrigerent leakage from water cooler cooling cap 150 litre, repair of cooling coil/condensing coil for minor leakage if any flushing of system and gas charging in the system up to required qty, and sealing / brazing/soldering complete all as specified and directed

S & F in repair replecement new sealed compressor for water cooling cap 40 litre (or nearest cap) single phase 230 volt, 50 HZ water complete complee all as specified and directed. Note : gas charging will be measured & paid separately

M&L for rewinding of condensor fan motor of 1/32 HP with same gauge of copper insualated winding wire including insulating material complete all as specified and direted.

S&F in repair following (BOQ item No. 92.00 to 96.00) spare part for water cooler complete all as specified and directed

Run capacitor 25/36 MFD, complete all as specified and directed

Condensor fan blade, complete all as specified and directed

Condensor fan motor, complete all as specified and directed

Thermostate

CP self closing push cock 15mm dia

M&L for repair of drain tray by brazing/ nickle polishing including replacement of drain pipe of water cooler complete all as specified and directed.

M&L for replacement of legs of same size of water cooler cap 80/150 litre complete all as specified and directed.

M & L for replacement of steel sheet (SS 304) of same gauge of body of water cooler including welding/ brazing etc , being into shape complete all as specified and directed.

M & L for two coat of spary painting complete outside of water cooler of cap 40/80 or 60/120ltr with harmartone paint over a coat of red oxide including scraping the old painted surface , denting and minor patch works complete all as specified and directed.

Attending complaint for Comprehensive maintainance and servicing of desert cooler of fan motor, water pump cleaning of PVC pipe testing including replacement of wood wool pad (set of three) etc for smooth functioning all as specified & directed.

M & L for rewinding of desert cooler motor of same gauge of copper insulated winding including material complete all as specifed and directed

M&L for fixing in replacement of plywood 6mm thick commercial grade in window of desert cooler, including painting of ply after coat of primer complete all as specified and directed.

S&F in repair following spare parts for desert cooler complete all as specified and directed

Capacitor 4.0 mfd

Fan motor with blade and clamp 106 watt or nearest cap single phase, complete all as specified and directed

Tullu pump /Water pump, complete all as specified and directed

M&L for preparation of surfaces of desert Cooler by scrapping old paint with sand paper, cleaning inner & outer surfaces of body and spray painting the inner surfaces and grills with two coats of black anticorrosive paint and outer surfaces with two coats of alluminium paint, over one coat of zinc chrome primer complete all as specified and as directed

Attending complaint for Comprehensive maintainance and servicing of split type air conditoner of capacity 1.5/2.0 Ton, cleaning of cooling/condensing coil,oiling of condenser fan motor, cleaning of air filter , detection of defective parts & replacement with new parts testing smooth functioning complete at site all as specified and directed. Note :- (i) Defective parts will be measured and paid separately . (ii) Job includes servicing , rectification of defects as one job (iii) Top up gas if required deemed to be included in unit rate Refrigerant gas will be measured as supply only.

S & F in repair replacement new sealed Rotary compressor of capacity 19000 BTU/Hour ( Nearest capacity ) , single phase 230 v , 50 Hz split type conditioner / window type air conditioner complete all as specified and directed. Note - Gas charging will be measured and paid separetly .

S & F in repair replacement hermatically sealed Rotary compressor of capacity 25000 BTU/Hour ( for 2 Ton AC) single phase 230 V , 50 Hz split type air conditioner all as specified and directed. Note - Gas charging will be measured and paid separately .

M & L for rewinding of condensor fan motor of split type AC of capacity 1.5 / 2.0 TR with same gauge of copper insulated winding wire including insulating material complete all as specified and directed.

M & L for taking down unserviceable burnt Indoor blower fan motor of split AC of capacity 1.5 / 2.0 TR , repairing / rewinding the same with super enamelled copper conductor of existing gauge, replacing the set of bearing including lathe work for making bearing seat complete & installing the same & commissioning complete all as specified and directed

Supply, installing of condenser coils of split AC capacity 1.5 TR in any location / position including disconnecting electrical mains, removing the clutter, wires, cleaning, removing dust / dirt, etc., around and replacing condenser coil and finally put the rest back together and commissioning including disposing of old unserviceable condenser coil complete all as specified and as directed. Note: charging of refrigerant shall be measured & paid separately complete all as specified and directed

Supply, installing of condenser coils of split AC capacity 2 TR in any location / position including disconnecting electrical mains, removing the clutter, wires, cleaning, removing dust / dirt, etc., around and replacing condenser coil and finally put the rest back together and commissioning including disposing of old unserviceable condenser coil complete all as specified and as directed. Note: charging of refrigerant shall be measured & paid separately complete all as specified and directed

S&F in repair spare part for split type AC complete for any make / Model of capaity 1.5 / 2 TR complete all as specified and directed

Run capacitor 45/36 MFD

PCB card

Cordless remote with battery

Condensor motor with Blade

Condenser fan blades for spilt type AC units of capacity 1.5T/2T

Indoor swing motor of capacity 1.5T/2T

Wiring kit for split type AC units 1.5/2TR

Indoor Blower wheel

Suction and discharge valve set for type split AC 1.5/2T

Refrigerant Gas R-22

Refrigerant Gas R-134A

Refrigerant Gas R-32

Refrigerant Gas R-410

Supply, installing and testing in repair outdoor unit comprising of copper Condensor coil , motor with blade ,compressor rotary type of 1.5 Ton Split type Air conditioner in any location / position including disconnecting electrical mains, removing the wires etc. and commissioning including disposing of old unserviceable outdoor unit deposited to MES AC section yard complete all as specified and as directed. Note: charging of refrigerant shall be measured & paid separately

Supply, installing and testing in repair Indoor unit of 1.5 Ton Split type Air conditioner in any location / position including disconnecting electrical mains, removing the wires etc. and commissioning including disposing of old unserviceable outdoor unit deposited to MES AC section yard complete all as specified and as directed. Note: charging of refrigerant shall be measured & paid separately

S&F metal clad switch socket outlet with single pole and neutral enclosure with two pin and earth plug socket with 01No. single pole MCB 20Amps 10kA complete all as specified and as directed

Taking down of split type air conditioner from existing location and installation after repair in same / other location including gas charging , testing , commisioning and comprising of following. (i)Replacement of refrigerant tubing with insulating sleeve upto 6RM with brass flair nut. (ii) Drain pipe upto 6RM (iii) Air conditioner bracket-1 set (iv) interconnecting cable from indoor unit to outdoor unit

M&L for GI earthing strip 32x6mm laid in trenches / fixed on wall with saddles for inter connecting /extension in earthing including excavation and earth work complete all as specified and directed

Material and labour for copper earthing strip 20mm x3mm laid in trenches / fixed on wall for inter connecting /extension in earthing including excavation and earth work complete all as specified and directed

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr deep in soft/loose soil for Erection of pole/laying cables etc., and getting out complete including forming bottom surfaces to required levels/slopes etc complete all as specified and as directed

Returning, filling-in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material(soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L filling approved river sand in trenches for sand cushioning of laying of cables to the full width of excavated trench 08 cm thick before laying the cable and 15 cm above the cable, gently punned down, stretching and testing of cable on transformer yard etc complete all as specified and directed. Note :- Thickness of sand cushioning after punning down i.e 18cm shall be measured for payment purpose only

Supply and laying well burnt fire Bricks of size 230x115x75 mm, locally available best quality (sub class "B" bricks) laid in trenches with 230mm side perpendicular to U/G cable for cable protection complete all as specified and directed.

M&L for boring/auguring suitable hole & insertion of 80 mm dia GI pipe including supply and inserting pipe not less than 600 mm below existing PCC/road/hard standing complete all as specified and directed. Notes:- Cost of equipment, tools & plants & material required for boring shall be deemed to be included in the rates quoted

M & L for PCC,1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in foundation, base of pole and in embedding blocks for stays complete all as specified and directed.

M&L for PCC,1:3:6 type C2 (using 40mm graded mechanically crushed stone aggregate)as in coping/collar of electric poles including use of necessary form work and concrete finished even and smooth without using extra cement complete all as specified and directed.

M&L for crimping type heavy duty copper lugs/ferrule suitable for cable cross sectional area 16/25 Sqmm complete all as specified and directed.

M&L for crimping type heavy duty copper lugs/ferrule suitable for cable cross sectional area 50/70 Sqmm complete all as specified and directed.

M&L for crimping type heavy duty copper lugs/ferrule suitable for cable cross sectional area 95/120 Sqmm complete all as specified and directed.

S&F LT heat shrinkable straight through joints of size 70 to 120 sqmm 3.5 core complete all as specified and directed

S&F LT heat shrinkable straight through joints of size 16 to 50 sqmm 3.5 core complete all as specified and directed

Taking UP/down the existing cables any description from trenches /poles/ walls etc complete all as specified and directed. Note :- Earth work shall be measured and paid separately.

Supply, laying, jointing and testing XLPE insulated, PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098 of 1995 and of size 4.0 core X 10 Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed

Supply, laying, jointing and testing XLPE insulated, PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098 of 1995 and of size 4.0 core X 16 Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed

Supply, laying, jointing and testing XLPE insulated, PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098 of 1995 and of size 4.0 core X 25Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed

Supply, laying, jointing and testing XLPE insulated, PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098 of 1995 and of size 3.5 core X 50Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed

Supply, laying, jointing and testing XLPE insulated, PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098 of 1995 and of size 3.5 core X 95Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated, PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098 of 1995 and of size 3.5 core X 120 Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed.

S&F in repair MCCBs 415V,16 KA, 4 Pole 63 Amp with Adjustable thermal magnetic release complete all as specified and directed.

S&F as in repair MCCBs 415V,25 KA, 4 Pole 100 Amp with Adjustable thermal magnetic release as complete all as specified and directed

S&F as in repair MCCBs 415V,25 KA, 4 Pole 125 Amp with Adjustable thermal magnetic release complete all as specified and directed

S&F as in repair MCCBs 415V,25 KA, 4 Pole 200 Amp with Adjustable thermal magnetic release complete all as specified and directed

S&F as in repair MCCBs 415V,36 KA, 4 Pole 250 Amp with Adjustable thermal magnetic release as specified as directed.

S&F as in repair Voltmeter Digital type suitable for 50-520 VAC(P-P), flush mounting complete all as specified and directed.

S&F as in repair Ampmeter Digital type suitable for 0-200Amps flush mounting complete all as specified and directed.

S & F in replacement of star delta starter suitable for 30 to 40 HP submersible pump with proper electrical connection including additional wiring etc complete all as specified and directed.

S&F in replacement of on load change over switch 415 V, 4 pole, 100 A as per existing make and model complete all as specified and directed.

S&F in replacement of on load change over switch 415 V, 4 pole, 125 A as per existing make and model complete all as specified and directed.

S&F in replacement on load change over switch 415 V, 4 pole, 250 A as per existing make and model complete all as specified and directed.

S&F in replacement of Contactor 3 pole 415 volts 200 Amps ML -12 (control voltage 230/415 as per existing model.) all as specified and directed.

S&F in replacement aviation obstruction light with all connected accessories to be fixed on GI Pipe 40/50mm bore light grade as per site requirement of existing make and model to be fixed on OHR or any other place complete all as specified and directed

Comprehensive maintenance & servicing /cleaning of Automatic power factor panel,replacement of worn out part detection of faulty component /wiring & testing complete all as specified and directed . Note: Spare parts shall be measured and paid separately as supply only

S&F in repairs power capacitor for APFC panel, power quality,heavy duty 25kVAR, 440V, 50Hz, double dielectric capacitor, with rated current 32.8A, required phase discharge device with resistance appropriate insulation level and rated current including suitable sized copper conductor cable, thimbles, diode and testing on fixing and connecting up complete all as specified and as directed.

M&L for painting of PCC/steel poles 9/11 m long alongwith road/ peri meter upto 1.5 m height from pedestal, with two coats of synthetic enamel paint in 30 cm height 5 block of each airforce pattern incl painting of pole, coping with black paint and writing pole Numbers with white paint on black circular base incl. marking of HT/LT with Painting of pole cross arms bracket with two coats of aluminum paint over a coat of red oxide primer complete all as specified all as directed by EIC .

M&L for painting of LT panels of any size and capacity, with two coats of synthetic enamel paint with two coats of aluminum paint over a coat of red oxide primer complete all as specified all as directed by EIC .

Periodical, preventive and comprehensive maintenance of DG set of Cap 10 to 15 KVA by Rep of authorised service centre as per manufacturer manual and checking of fuel supply system, Lubrication system, cooling system, battery ignition system and rectification of defect, inspection/testing of engine and alternator for smooth functioning of the DG set and including the replacement of following :- (i) Fuel/ lub filter one set (ii) Coolant in radiator (iii) Testing of engine control panel (iv) Cleaning of radiator, minor repair of leakages to be rectified. (v) Hose pipe set (vi) Fuel pipe/lubricant pipe (vii) Engine oil. Note: (i) Worn out parts repair/replacement if any other than above shall be measured and paid seprately.

Periodical, preventive and comprehensive maintenance of DG set of Cap 40 to 63 by Rep of authorised service centre as per manufacturer manual and checking of fuel supply system, Lubrication system, cooling system, battery ignition system and rectification of defect, inspection/testing of engine and alternator for smooth functioning of the DG set and including the replacement of following :- (i) service kit for elements of fuel/air/lub filter one set (ii) top up of coolant in radiator (iii) Testing of engine control panel (iv) Cleaning of radiator, minor repair of leakages to be rectified. (v) hose pipe set (vi) fuel pipe/lubricant pipe (vii) Engine oil. Note: (i) Worn out parts repair/replacement if any other than above shall be measured and paid seprately.

Periodical, preventive and comprehensive maintenance of DG set of Cap 100 by Rep of authorised service centre as per manufacturer manual and checking of fuel supply system, Lubrication system, cooling system, battery ignition system and rectification of defect, inspection/testing of engine and alternator for smooth functioning of the DG set and including the replacement of following :- (i) service kit for elements of fuel/air/lub filter one set (ii) top up of coolant in radiator (iii) Testing of engine control panel (iv) Cleaning of radiator, minor repair of leakages to be rectified. (v) hose pipe set (vi) fuel pipe/lubricant pipe (vii) Engine oil. Note: (i) Worn out parts repair/replacement if any other than above shall be measured and paid separately

Supply only following spare parts of DG set of kirloskar/Cummins DG set complete all as specified and directed.

V belt

Battery Terminal

Battery 90AH, maintenance free Genplus 12volts complete all as specified and directed.

Taking down old unservicable any type street lights and refixing after repair of street light /security lights including cleaning of perplex cover where ever required and tightening of loose connection on the pole, Complete all as specified and directed.

S&F PVC 3 core Cord Flexible copper insulated cable 1.5Sqmm/core in size Black/Grey colour omplete all as specified and as directed.

Taking down the unserviceable bracket and M&L for new bracket made out of 40mm GI tubing light grade 1.5m lay bent to shape suitable for fixing of any type street light fitting fixed to steel/concrete pole with two MS clamps made out of 50 x 6 flat iron, 16mm dia bolts nuts and washers of suitable length all as specified and directed.

M & L for FRP looping box with hinged cover weather proof with locking arrangement and appropriate size of aluminium bus bar of capacity 100 amps for single phase 230 V, 50 Hz electric supply mounted on PVC insulaters and fixed to pole by means of MS clamps, nuts boltss and washers including cables connection including one MCB SP 6 amps including taking down existing looping box complete all as specified and directed.

S&F 1100 volts grade heavy duty two single core cables PVC insulated stranded aluminium conductor of size 6 sqmm served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including4mm suspension wire, one twin core cable flat or circular and including taking down old unserviceable wire dispose from site complete all as specified and directed.

S&F LED street light fitting 60 Watt 230 V AC warm white outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection and including taking down old unserviceable wire dispose from site complete all as specified and directed.

S&F LED street light fitting 90 Watt 230 V AC warm white outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection and including taking down old unserviceable wire dispose from site complete all as specified and directed.

Removing/taking out non clog type submersible sewage pumping set capacity 3 to 5 HP from sewage well after dewatering of sewage water and Rewinding of motor 3 to5HP of Non clog type submersible pumping set with suitable size of copper winding wire incl all insulation material & motor winding with pump dismantling the same for assessing & carrying out the repair/service as involved in subsequent items making good in running condition by repair/replacement of all unserviceable spare parts etc re-assembling, lowering the same into the well and making necessary connections, testing complete all as specified and directed.

Taking up/down steel tubing GI pipelines/connection from trenches/wall / roof incl connected fittings/accessories and cleaning for refixing or removal to store for 15mm bore complete all as specified and directed.

Taking up/down steel tubing GI pipelines/connection from trenches/wall /roof incl connected fittings/accessories and cleaning for refixing or removal to store for 20mm bore complete all as specified and directed.

Taking up/down steel tubing GI pipelines/connection from trenches /wall /roof incl connected fittings/accessories and cleaning for refixing or removal to store for 25mm bore complete as specified and directed.

Taking up/down steel tubing GI pipelines/connection from trenches /wall incl connected fittings/accessories and cleaning for refixing or removal to store for 40mm or 50mm bore complete all as specified and directed.

Supply and laying in trenches / fixing on wall / roof steel water tubing galvanised 15mm bore medium grade ISI marked with all fittings complete all as specified and directed by Engineer-in-Charge.

Supply and laying in trenches / fixing on wall / roof steel water tubing galvanised 20 mm bore medium grade ISI marked with all fittings complete all as specified and directed by Engineer-in-Charge.

Supply and laying in trenches / fixing on wall / roof steel water tubing galvanised 25 mm bore medium grade ISI marked with all fittings complete all as specified and directed by Engineer-in-Charge.

Supply and laying in trenches / fixing on wall steel water tubing galvanised 40 mm bore medium grade ISI marked with all fittings complete all as specified and directed by Engineer-in-Charge.

Supply and laying in trenches / fixing on wall steel water tubing galvanised 50 mm bore medium grade ISI marked with all fittings complete all as specified and directed by Engineer-in-Charge.

Supply, fixing and testing Gun metal Gate valve 50 mm dia screwed body ends and cast iron hand wheel conforming to IS :778 –1984 and ISI marked complete all as specified and directed.

Supply, fixing and testing Gun metal Gate valve 40 mm dia screwed body ends and cast iron hand wheel conforming to IS :778 –1984 and ISI marked complete all as specified and directed.

Supply, fixing and testing Gun metal Gate valve 25 mm dia screwed body ends and cast iron hand wheel conforming to IS :778 –1984 and ISI marked complete all as specified and directed.

Supply, fixing and testing Gun metal Gate valve 20 mm dia screwed body ends and cast iron hand wheel conforming to IS :778 –1984 and ISI marked complete all as specified and directed.

Supply, fixing and testing Gun metal Gate valve 15 mm dia screwed body ends and cast iron hand wheel conforming to IS :778 –1984 and ISI marked complete all as specified and directed.

Supply, fixing, testing and commissioning Double flanged non-rising stem type cast iron sluice valve suitable for 150 mm dia bore pipe with hand wheel and suitable for pressure rating of PN :1.6 duly drilled holes for fixing of nuts and bolts, stem made of high tensile brass ISI marked and conforming to IS : including rubber gasket, nuts, bolts and washers complete all as specified and directed.

M&L for run lead joints of spigot and socket pipes and fittings for DI/CI pipe 150 mm bore size of pipe including provision of bolts, washers and white lead or mineral oil complete all as specified. Note;- Earth work will be measured and paid separately,

M&L for run lead joints of spigot and socket pipes and fittings for DI/CI pipe 100 mm bore size of pipe including provision of bolts, washers and white lead or mineral oil complete all as specified. Note;- Earth work will be measured and paid separately.

M & L for lifting of column pipe, flanged 100mm bore with submersible cable from bore hole of tube well, pump set of any capacity and lowering after repair in borewell complete all as specified and directed by Engr-in-Charge. Note: (i) Lifting & lowering of pump set upto 120 mtrs deep will be deemed to be included in unit rate. (ii) Lifting & lowering of pump set to be completed out within 24 hrs from intimation. (iv) Rubber gasket, nuts & bolts for replacement deemed to be included in unit rate.

Opening of submersible motor for rewinding with PVC coated copper winding wire as per existing gauge insulation material,after stripping of existing worn out winding, M&L for sealing kit, O- ring, Gasket, water drain plug, sand guard, cable packing ring, cable gland ring, upper/lower bearing, adopter piece, motor key, upper lower flange, neck ring, suction case, Hex bolt, Circlip washer, Motor coupling, thurst plate,motor bush etc complete, reassembling with pump set of the capacity upto 35 HP complete all as specified and as directed

M&L for Repair/Overhauling of submersible pump set including replacement of Hex bolt, Circlip washer, bowl stud, pump shaft, rotor bleach, pump bush etc complete and reassembling pump set of capacity upto 35 HP complete all as specified and directed. Note : Impeller shall be measured and paid separately as supply only.

M&L for rewinding of Induction motor 5HP with Copper winding wire are per exisiting size and type incl all type packing/gaskit/nutbolt along with all insulation material & motor winding provided with thermal switches for protection against excessive temperature rise complete all as specified and as directed.

M&L for Cleaning, Desludging/ dewatering of valve pit chamber, Bailing out the leakage water and fill the gland packing & rubber packing in sluice valve etc complete all as specified and directed by Engineer-in-Charge.

Potable water chemical analysis testing of water to be conducted by laboratories authosied by NABL, PPCB & CPCB. The test will analyse pH,colour, Odour, Taste, Turbidity, total Hardness, Total Alkalinity, Iron, chloride, Residual Free Chlorine, Fluroide, Total Dissolved Solid, Sulphate, Nitrate, Total Coliform, E.coli etc including collecting of water from the source in a spacilised glass bottle used for this purpose, and collecting the reports from the Lab, complete all as specified and directed.

Cleaning of SWT capacity of 50000 Gln water thoroughly by removing mud grits etc complete all specified and directed. Notes : rates quoted shall deemed included for followng :- (i) Cleaning inner surfaces of tanks complete with scraping wth steel wire bruses, pressure wash, removing mud, sludge collected inside the tank manualy, removal of mud to a distance not exceeding 50mtrs. (ii) Washing with clean water and bieaching powder or with high strength calcium chloride mxture thoroughly internally removing left out sludge if any to a distance not exceeding 50 mtrs including writing capacity of SWT, cleaning date, due dated for cleaning with black synthetic enamel paint with existing pattern.

Cleaning of OHT capacity of 75000 Gln water thoroughly by removing mud grits etc complete all specified and directed. Notes : rates quoted shall deemed included for followng :- (i) Cleaning inner surtaces of tanks complete with scraping wth steel wire bruses, pressure wash, removing mud, sludge collected inside the tank manualy, removal of mud to a distance not exceeding 50mtrs. (ii) Washing with clean water and bieaching powder or with high strength calcium chloride mxture thoroughly internally removing left out sludge if any to a distance not exceeding 50 mtrs including writing capacity of OHT, cleaning date, due dated for cleaning with black synthetic enamel paint with existing pattern.

M&L for attending of water supply complaints for any leakage / blockage in GI pipe lines of size 20mm / 25mm/40mm /50mm bore taking up serviceable / unserviceable GI water pipe lines all fittings/fixtures from trench including supply and laying GI tubing 20mm / 25mm/50mm bore up to 1 mtr length (max) including necesssary cutting, threading suitable for 20mm / 25mm/50mm including necessary excavation and earth work up to 1 Cum to repair the leakage / clearing the blockage in the pipe line and testing on completion complete all as specified and directed NOTE : Excavation more than 1 Cum and GI fittings shall be measured and paid separately under relevent item of this schedule

M&L for taking down high pressure SV/ MV/ MH /FTL/LED street light fitting and Flood Light fittings of any wattage / any height of pole/ walls/ watch tower any location for repairs or replacement of burnt out the accessories and rectifying the fault complete all as specified. Note: - LED Drivers, Surge protection and cable shall be measured separately under relevant items of schedule

S&F in replacement 5 KV SPD for LED street light, 230 volts, 50 HZ compatible for industrial & outdoor LED Fixtures up to rated power of 120W /90W /70W for fixing in repairs complete all as specified and directed.

S&F in replacement Drivers for LED street lights 45W/ 70W / 90W / 120W, 230 Volts, 50 HZ complete all as specified and directed.

S&F in replacement Drivers for LED flood light 70W / 90W / 120W/ 250W, 230 Volts, 50 HZ complete all as specified and directed.

S&F LED flood light 250 watt 230 V AC Lumen effeciency=≥ 115 Im/W, colour Temp 5500 - 6500 Kwith inbuilt secondary Lens outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp, thermal management in multiple optics complete with IP 65/66 protection with suitable size bracket and clamps,nut ,bolts washer etc including taking down existing unserviceable lights any type complete all as specified and as directed.

S&F LED flood light 300 watt 230 V AC Lumen effeciency=≥ 115 Im/W, colour Temp 5500-6500 K with inbuilt secondary Lens outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp, thermal management in multiple optics complete with IP 65/66 protection with suitable size bracket and clamps,nut ,bolts washer etc including taking down existing unserviceable lights any type complete all as specified and as directed.

S&F post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed by Engr-in-charge

S&F of Automatic sequential timer switch digital wall mounted type with timer setting 1 min to 720 min, Temp setting 10 degree to 30 degree, high temp alarm, low temp alarm, temp calibration and delay time settings, capable to take load up to 2 TR 2/3/4 window/split type AC unit with auto/manual facility and do complete connection and wiring with existing AC units complete all as specified and directed by Engr-in-charge.

Demolition of Brickwork or stone boulder masonry/PCC block masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework & precast concrete articles and disposing off rubbish outside MD land complete all as specified and directed.

M&L for Brickwork with sub class B bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete all as specified and directed

M&L for brick work with sub class'B' bricks,straight or curved on plan to any radius in half brick thick wall built in CM 1:4. complete all as specified and directed

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15cm below or above ground level a complete all as specified and disposing off rubbish outside MD land complete all as specified and directed.

M&L for 75mm thick PCC type D-2, (1:4:8) using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified and directed.

M&L for 100 mm thick plain cement concrete 1 : 2 : 4 type B2 (using 20 mm graded mechanically crushed stone aggregate) as in hard standing laid in panels including necessary form work, finished by spike rolling surfaces of concrete and Forming construction joints 30 mm deep and 10 mm wide filled with sealing compound grade 'A complete all as specified and as directed

M&L for Chequered cement concrete coloured commercial Tiles 30CM x 30CM x 20 to 22mm thick of with grey cement and pigment set jointed and pointed in neat cement slurry in floors and cut and polished laid and over 15mm Screed in CM 1:6 all as specified and as directed.

M&L for 80mm thick machine pressed rubber moulded precast concrete M-40 interlocking coloured paver block any shape and size conforming to IS-15658-2006 with grey cement and pigment including taking down of old paver block complete all as specified as directed.

M&L for Sand filling under floors including watering and consolidation complete all as specified as directed.

Demolition of cement concrete (un-reinforced) in any description & in any position not otherwise specifically provided for as in coping, benching, bed block , kerbs etc and disposing off rubbish outside MD land complete all as specified and directed.

M&L for Providing, cement concrete in 1:2:4 type B1 (using 20mm graded mechanically crushed stone aggregate) roof kerbs , Interlocking Tile/Paver Block or mud stops, rounded or chamfered on edges complete all as specified and directed

M&L for PCC in 1:2:4 type B1 (using 20mm graded mechanically crushed stone aggregate) as in coping, benching and similar work incl form work complete all as specified and directed

M&L for PCC in surface channels and drains type C-1 (1:3:6) using 20 mm graded mechanically crushed stone aggregate complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/stopped end etc complete all as specified and directed

Add or deduct for each 25 mm girth or part thereof over or under 30 cm ditto complete all as specified and directed

Demolition of RCC of any description & in any position (reinforcement cut as required to facilitate demolition) and disposing off rubbish outside MD land complete all as specified and directed.

M&L for Mild steel TMT bars of 10 mm dia as in reinforcement, cut to length, bent to shape required, including cranking, bending, spirally looping for columns, hooking ends & binding with and including mild steel annealed wire of not less than 0.9 mm dia or securing with clips complete all as specified and directed

M&L for Precast RCC 1:2:4 type B1 (using 20mm graded mechanically crushed stone aggregate) as in cover slab of drain, culvert and the like set in CM 1:4 complete all as specified and as directed.

Taking down cement plastering of any thickness on brick, concrete or stone walls, partitions, ceilings etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed

M&L for 15mm thick rendering on brick or concrete surface in cement mortar 1:4 and finishing the surface with even and smooth without using extra cement complete all as specified and as directed.

M&L for rough cast plaster incl 15 mm thick CM 1:3 on brickwork or concrete surface complete all as specified in SSR Part-I clause 14.22 complete all as specified and directed. Note: Rough cast finish to be as described below: After applying the under coat of cement mortar 1:3 and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg( which is generally of size between 6 to 12 mm depending on the texture required) mixed with course sand and cement in the ratio 1:1:1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger agg are thoroughly covered.

M&L for Applying two coats of cement base paint over alkaline primer on new wall surface including preparation of surface, complete all as specified and directed

Dismantling wrought iron of mild steel work of any description not otherwise provided for complete all as specified and as directed by the Engr-in-Charge.

Supply and fabricating framed steel work and fixing as in doors or gates of angle or other section with gusset plates, rails, braces, etc., Fe-290 (Gde E-165) complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (incl of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground (Posts embedded in concrete) complete all as specified and directed

Excavation in soft soil for post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exceeding 50m and making good surface, work in any type of soil, complete all as specified and directed

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by the Engineer-in-Charge

M&L Plain Cement Concrete (1:3:6) type C-2, using 40 mm graded mechanically crushed stone aggregate as in foundation filling of posts and struts., etc., complete all as specified and as directed.

S&F in repair galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for Preparation of new steel surfaces exceeding 10 cm in width or girth, applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed..

M&L for Applying one coat of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface complete all as specified and directed

Demolition and breaking up 150 mm dia drain pipes, including bed concrete for Salt glazed ware, UPVC, AC, or Reinforced cement concrete pipes, set in cement mortar incl excavation of earth work and removing the rubbish outside MD land complete all as specified and as directed.

Demolition and breaking up 200 mm dia drain pipes, including bed concrete for Salt glazed ware, UPVC, AC, or Reinforced cement concrete pipes, set in cement mortar incl excavation of earthwork and removing the rubbish outside MD land complete all as specified and as directed.

M&L for Plain cement concrete bed to 150 mm bore drain pipe including packing under and haunching against the sides of pipes, after they are laid and tested, with plain cement concrete 1:4:8 type D2 (using 40 mm graded mechanically crushed stone aggregate) all as specified and directed.

M&L for Plain cement concrete bed to 200 mm bore drain pipe including packing under and haunching against the sides of pipes, after they are laid and tested, with plain cement concrete 1:4:8 type D2 (using 40 mm graded mehcanically crushed stone aggregate) all as specified and directed.

M&L for 150mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid under trenches jointed in CM (1:1) complete all as specified and as directed.

M&L for 200mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid under trenches jointed in CM (1:1) complete all as specified and as directed.

Cutting into existing manholes for connecting new drains ,making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished,and reforming benching as required for 150mm bore pipe, complete all as specified and as directed..

Cutting into existing manholes for connecting new drains ,making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished,and reforming benching as required for 200mm bore pipe, complete all as specified and as directed..

Cleaning of manhole of any description & size and exceeding 1.5 M in depth including lifting up and removing sludge & accumulated solid/semi solid sludge and any other foreign material with mechanically & washing down with water for smooth functioning of sewage line all as directed, sludge obtained from cleaning shall be removed outside MD land complete all as specified and as directed.

All as per BOQ srl item No.275.00 here-in-above but depth exceeding 1.50M but not exceeding 3.00M, complete all as specified and as directed.

M&L in repairs for 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints or jointed with solvent cement joint, laid in trenches or in floors,type B, conforming to IS 13592-1992 supplied laid , jointed & tested including taking out/down old pipes complete all as specified and directed by Engineer-in-charge. Note - Rubber rings for pipes and fittings shall conform to IS 5382-1985.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and directed by Engineer-in-charge.

M&L for 15mm thick rendering on brick or concrete surface of manholes, drain and septic tank/soakage well in cement mortar 1:4 and finishing the surface with using water proofing compound even and smooth without using extra cement all as specified and as directed. Note: Water proofing compound shall be measured and paid seperately

Supply only water proofing compound liquid complete all as specified and as directed.

M&L for preparation of old or previously treated surfaces of RCC / Stone / Concrete / brick walls/ Asbestos Cement Sheet or plastered surfaces and applying one coat of exterior acrylic emulsion paint in camouflaging pattern of any shape and any size complete all as specified and directed by Engineer-in-charge, Note: Sample of camouflage pattern to be approved as per the user requirement by GE.

M&L for Desilting and cleaning of blocked covered and culvert etc by removal of mud, soil, aggregate and other similar waste material for smooth flowing/functioning of storm water and disposing off rubbish outside MD land complete all as specified and directed.

M& L for dewatering of soak well completely of size not exceeding 3mtr dia and note exceeding 6 mtr depth by means of pumping out of water to movable mechanical transport like tanker (attached to tractor/truck) and disposing off the water out side of defence land complete all as specified and directed.

Cleaning of the under ground sewer line upto 150mm dia of any type all in working/running conditions involving removal of blockage of any kind lines by means of mechanical rodding with vibrations/drilling concept i.e trolley mounted motorized sewer cleaning machine including desluding, descaling and dechoking whereever reqired, flushing the entire stretch with combined high pressure water jetting cum suction (vacum) type machine suitably mounted on HCV having facilities of hydraulic applications throught hight pressure thermo plastic fiblr based water jetting hose and through conical/round shape nozzle pipes, making the stretch clean and founctinal and removal/deposition of sludge inclusive of solids if any & sludge water to a distance not exceeding 500 mtrs beyond the periphery of defence land and covering the entire sludge and solids with local sand/earth all as directed.

M&L for preparation of old or previously treated surfaces of RCC / Stone / Concrete / brick walls/ Asbestos Cement Sheet or plastered surfaces and applying two coat of exterior acrylic emulsion paint in camouflaging pattern including 2mm thick putty of any shape and any size complete all as specified and directed by Engineer-in-charge, Note: Sample of camouflage pattern to be approved as per the user requirement by GE

Cleaning the septic tanks in use of capacity upto 50 -100 users by taking out complete sluge including sludge water & solids if any,machanically by HCV mounted suction/discharge machine having blow back facility with sludge tank not less than 6000 ltrs capacity removing & disposing the entire retrieved material to a distance n exc 500 mtr outside the periphery of defence land & covering the entrie sludge with local sand /earth, complete all as specified and as directed.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and directed by Engineer-in-charge.

Supply, Installation, testing & commisioning of intelligent addressable multisensor type (combination of Heat & smoke), detectors with base as in repair complete all as specified and directed. The detectors shall sense real fire/smoke and generate alarm if any fire/smoke occurred in the building. Make: EST or compatible with existing in other i.e siemens/Agni Protection.

Supply, Installation, testing & commisioning of intelligent addressable Heat detector as in repair complete all as specified and directed. The detectors shall sense real fire/smoke and generate alarm if any fire/smoke occurred in the building. Make: EST or compatible with existing in other i.e siemens/Agni Protection.

Supply, Installation, testing & commisiong of addressable manual call point (MCP) as in repair shall be housed in metallic box. The address module shall be in-built and shal lform part of loop module. The MCP shall be red colour with red LED for display of fire complete all as specified and directed by Engr-in-Charge. Note: Break Glass type MCP with chain and hammer is not acceptable. Make: EST or compatible with existing in other i.e siemens/Agni protection.

Supply, Installatin, testing & commisiong of loop driven addressable sounder/Hooter with strobe in built as in repair. The addressable soundre/Hooter with strobe shall form part of loop devices such that, no addtional seprate wiring is required. The sounder/ Hooter shall have audible range of 93 DB when heared at distance of 1.00mtr. the shounder/Hooter shall be suitable for wall/ ceiling mounting and shall operate on =24 volts DC complete all as specified and directed by Engr-In-Charge. Make: EST or compatible with existing in other i.e siemens/Agni protection.

Supply, Installation, testing & commisioning of Main fire Alarm panel PPSM card (power supply Unit) as in repair complete all as specified and directed. Make: EST or compatible with existing in other i.e siemens/Agni protection.

Supply, installation, testing & commisioning surge protector as in repair complete all as specifeid and directed by Engr-in-Charge. Make: EST or compatible with existing in other i.e siemens/Agni protection.

Supply, Installation, testing & commisioning of External power supply unit for hooter operating 5Amp as in repair complete all as specified and directed by Engr-in-Charge.

Providing M&L for SDU Backup creation and Re-programming including All devices cleaning and complete data base creation complete all as specified and directed by engr-in-charge.

Esha Engineers (BID ID -3478467)

SWAMI ENGINEERS (BID ID -3479270)