RETENDER-Annual Plan-447/24-Kattappana muncipality Vattakkattilkkunnu dwp ward 30

Amount

Drilling of bore well

OD124505/2023-2024:Drilling borewell with internal diameter of 110 mm , as per ground water department estimate

OD124526/2023-2024:Providing Casing pipe PVC 140 mm 6 kg/cm2

OD124525/2023-2024:Providing 140 mm PVC end cap

OD140084/2023-2024:Supplying and fixing 5HP submerssible bore well motor pump of approved brands including essential fittings.

OD140110/2023-2024:Supply and fixing pump starter with control panel for 5 hp mortor pump set including all cost of conveyance labour etc complete

OD124524/2023-2024:Providing , laying and fixing nylon rope for fixing submersible motor

OD351438/2023-2024:Supply and fixing 6 mm cable including all cost of conveyance labour etc complete

OD124522/2023-2024:Supplying and fixing 40mm dia 10kg/cm2 HDPE pipe,PE-80, including specials and all fitting charges but excluding trenching and fillling etc.complete.

motor shed

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

OD128959/2023-2024:DRY RUBBLE MASONRY WITHOUT CONCRETE LEVELLING COURSE MASONRY BLASTED RUBBLE INCLUDING PACKING TO COMPACTNESS TO LINES AND LEVELLS,COST AND CONVEYANCE OF ALL MATERIALS LABOUR CHARGES ETC.COMPLETE AS PER DIRECTION OF DEPARTMENTAL OFFICERS AT SITE

50.6.1.7:Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15 cm in : CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

9.119:Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door fame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer-in Charge.

9.120.1:Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and sized of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of whicj 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5mm thick, 95 mm wide PVC sheet out of which75 mm shall be tapered in 45 degree on th inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mmx2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded /sealed to the styles & rails with 7 mm (5 mm + 2 mm ) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer -in-charge, manufacture's specification & drawing.30 mm thick plain PVC door shutters

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.8:Providing non- asbestos high impact Polypropylene reinforced cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J or L hooks, bolts and nuts, 8 mm dia G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafter and trusses), including cutting sheets to size and shape wherever required.

THOMAS K JOSEPH

NEW KERALA BUILDERS

Bidder Name

SIBICHAN THOMAS

NEW KERALA BUILDERS

THOMAS K JOSEPH