E-Nit 10/2026-27

Dressing of earth work in surface excavation including cutting and filling upto30cm depth including disposal of excavated earth upto50m and lift upto 1.5 m.

Construction of embankment with approved material obtained from borrow pit with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8-10 tonne to meet requirement of table 300-2 including cost of compensation for earth taken from private land complete as per MoRT&H specification clause 305. (Lead taken upto 5 km)

Brick work with FPS bricks of class designation 75 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Made of 3' round pipe mild steel black pipe with fix height fix on ground(H-schedule)

THI-CHI SPINNER (2 WHEEL) Providing and fixing of Thi-Chi spinner (2 Wheel) of size 700mm (Length) x 1000mm (Width) x 1280mm (Height) fabricated with a center pipe of 100NB shall be made up of “C” Class G.I. pipe. The handle movement round frame shall be made up from 25 NB “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mmCRC square pipes of 3mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø 25 mm of SAE8620 bright material. The bearing shall be used of “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile S.S. nut bolts shall be used for assembly. Foundation cover Closing Cap shall be made from FRP Material with 0.7 mm thickness. The cerclips used for assembly shall be of of A24 and A11. The nylon bush shall be used for handle knob. The powder coating shall be done with pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc (H-schedule)

SEATED PULLER Providing and fixing of Seated Puller of size 1900mm (Length) x 740mm (Width) x 1920mm. (Height) fabricated with a center pipe is of 100NB shall be made from “C” Class G.I. pipe. Bottom support of M.S. round plate of Ø 250 mm &10mm thickness shall be welded. All linkages shall be made up of 25NB “C” class G.I. pipe. The handle frame of 32NB “C” class G.I. pipe. The seat frame of 32NB “C” class G.I. pipe, To build structure bushes to be used which shall be made from seamless pipe of 60mmO.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mmCRC square pipes of 3mm thickness. Foundation cover Closing Cap shall be made from FRP Material. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used of “ 6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for assembly are of A16 The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc (H-schedule)

DOUBLE TWISTER STANDING Providing and fixing of Double Twister Standing of size 1500mm (Length) x 600mm (Width) x 1300mm. (Height) fabricated with a Center Pipe of 100NBshall be made from “C” Class G.I. material. The bottom shall be welded with support of M.S. round plate of Ø250 mm &10mm thickness. The bottom frame of 32NB shall be made from “C” class G.I. pipe. The handle frame of 25NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB”C” class welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mmCRC square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size Ø300mm and 10mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35 mm shall be made up from SAE 8620 bright material. The bearings shall be used are of “6205zz” permanent lubricated sealed bearing of reputed. Brand. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc (H-schedule)

SEATING & STANDING TWISTER Providing and fixing of Seating & Standing Twister of size 1700mm (Length) x 540mm (Width) x 1250mm. (Height) fabricated with a Center Pipe of 100mm NB shall be made from “C” Class G.I. Round Pipe. The M.S. round plate of Ø250 mm &10mm thickness shall be welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm should be provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister of 32 NB, 50 NB, and 25 NBshallbe made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe of 25mm NB. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mmCRCA square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The Pins to be used which shall be made up of Ø 35 mm SAE 8620 bright material. The bearings shall be made of of “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc (H-schedule)