REPAIR TO KITCHEN CABINET AND JOINERIES IN OMQ AREA AT AF-I UNDER GE (AF) JAMNAGAR NO.2

Amount

Taking down shutters of any description n.exc 1 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but n.exc 2 Sqm each complete all as specified and directed.

Taking down chowkats or frame with shutter (with out taking off shutter from the frame) n.exc 1.5 sqm complete all as specified and directed.

Taking down chowkats or frame with shutter (with out taking off shutter from the frame) .exc 1.5 sqm but n. exc 4.0 sqm area of each complete all as specified and directed.

S&F IInd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S & F 35 mm thick II class hard wood Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters complete all as specified and directed.

S & F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F Solid PVC door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supply & fixing in opening as per specification and complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (stiles) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, including stainless steel butt hinges 100 mm long, Aluminium tower bolt tower bolt 100 mm long and Aluminium handle 150 mm long as per specification and complete all as specified and directed.

S & F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M & L for 100mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed.

M & L for 75mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S&F 100mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S&F 150mm long aluminium handle fabricated type anodised complete all as specified and directed.

S&F 100mm long aluminium handle fabricated type anodised complete all as specified and directed.

S&F 250mm x 16mm dia aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of steel cast or extruded section or cast aluminium alloy complete all as specified and directed.

S & F 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 300 mm long MS ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall be of size 101.60 x 44.75 x 2.4 mm (Section No 14021) (b) Vertical Members of shutter Section shall be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370).

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track window ( two shutters glazed ) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in Member for wire gauge Section shall be 18.00 x 25.00 x 1.35 (Section No 20791). position, concelled type lock for all two shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20831) (b) Frame (bottom) section shall be of size 92.00 x 31.75 x 1.50 mm ( Section No 20832) (c) Top & side Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 (Section No 20738) (d) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.45 (Section No 20737) (e) Bottom Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 (Section No 20736). Note:- Section No given above are of make Jidal, Contractor may use similar section of other make mention in Appx B.

S&F aluminium (powder coated with approved colour) ventilator, partialy glazed and partialy louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aparture with 25x3mm thick aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old ventilator complete all as specified and directed. Note:-(i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B.

S & F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40 mm to wooden / iron / aluminium frame with wooden / iron / aluminium beading and fixed with nails / nut & bolts or wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick figured glass pin head type glazing with oil putty n.exc 0.50 Sqm in each pane fixed to wooden / metalic frame complete all as specified and directed.

Welding in repairs over metal/steel surfaces of any thickness exc 2.5 cm & n exc 5 cm in length complete all as specified and directed.

S & F in repair 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F in repairs for mild steel butt hinges medium grade 100 mm size complete all as specified and directed.

S & F in repairs for mild steel butt hinges, medium grade 75mm size complete all as specified and directed.

S & F in repairs 150mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S & F in repairs 100mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S & F in repairs 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F in repairs 100 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F in repairs 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of steel cast or extruded section or cast aluminium alloy complete all as specified and directed.

S & F in repairs 20 mm dia curtain rails, mild steel, chromium plated with fixing brackets / concealed brackets & holders, stops, rollers etc.decorative type fitting complete all as specified and directed.

Repairs and fixing only existing curtain rails, mild steel, chromium plated with fixing brackets / concealed brackets & holders, stops, rollers etc.decorative type complete all as specified and directed.

S&F mild steel hold fast and similar works fabricated with mild steel section conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L for PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) for fixing hold fast including necessary formwork, complete all as specified and directed.

Forming jambs, etc. to openings (to foregoing item),in Cement mortar 1:6 including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed.

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries to a distance exc 1.5 Km but n. exc 2 Km. complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on brick or stone walls to be finished even and smooth (without using extra lime or cement) complete all as specified and directed .

M & L for preparation of new plastered surfaces of walls & applying two coats of distemper oil emulsion over a coat of chalk whitening compatible primer complete all as specified and directed.

M&L for preparing sufaces of new, previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and priming with pink primer and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparing old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F in repairs hasp and staple 75mm size, of aluminium anodised including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F in repairs 300 mm long MS ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repairs door closer hydraulically regulated, designation No.2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for preparation of new surfaces of steel exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S & F in repairs 40mm width continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S & F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel over, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including taking down of aluminium / glass / toughen glass shutter complete all as specified.

Resecuring or easing & adjusting without taking down the shutter of any description n.exc 1 Sqm in same opening complete all as specified and directed.

Resecuring or easing & adjusting without taking down the shutter of aluminium / metalic / wooden shutters exc 1 Sqm but n.exc 2 Sqm in same opening complete all as specified and directed.

S & F 2nd class hard wood Plain fillets. square, rectangular but bullnosed, splayed, chamfered or rounded on one edge or face not exc 3.0 sqcm complete all as specified and directed.

S & F in repair 12mm thick (7 Nos ply) plywood, Type BB (with BWR) complete all as specified and directed.

S& F in repairs 18/19 mm thick plywood (12 Nos of ply) grade BWR, type BB fixed width screws to timber frme work or plywood complete all as specified and directed.

M & L for 0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F in repairs 75mm size SS cup board hinges medium weight cold rolled all as specified and as specified.

S&F in repairs magnatic catcher and connected plate to shutters and frame as per Sample complete all as specified and directed.

S&F in repairs locks, cupboard, grade I, size 75 mm 4 levers complete all as specified and directed.

S & F in repairs drawer handles, projection drop (50mm to 65mm) on screwed plate complete all as specified and directed.

S&F in repairs 50mm dia, polished, hard wood cupboard knobs fixed with screws complete all as specified and directed.

S& F in repairs Telescopic Channel of size 450mm (when closed), mild steel chromium plated, roller type, heavy duty etc complete all as specified and directed.

S&F in repairs brass hat and coat hooks, solid body, 175mm to 250 mm of Minimum 05 hooks complete all as specified and directed.

Dismantling of floor, hearth or wall tiling, incl cement mortar bedding (but not backing) and rubbish off the premises including removal of debris to a distance exc 1.5 but n exc 2.00 km complete all as specified and directed.

M & L for 25 mm thick cement concrete type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in levelling course in flooring complete all as specified and directed.

M&L for non - skid coloured ceramic tiles (1st quality) square/rectangular of 7 to 8 mm thick area of each tiles exc 0.06 sqm but n exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for non - skid coloured ceramic tiles (1st quality) square/rectangular of 7 to 8 mm thick area of each tiles exc 0.11 sqm but n exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 300 x 450 x 7mm / 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with coloured cement to match the tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

S & F in repairs kitchen basket fabricated with stainless steel section (SS-304) best quality of size 430mm x 508mm x 100mm for different use such as placing plane plate / disc / cup / saucer / cutlery / thali / etc fixed in position complete all as specified and directed.

S & F in repairs kitchen basket fabricated with stainless steel section (SS-304) best quality of size 430mm x 508mm x 200mm for different use such as placing plane plate / disc / cup / saucer / cutlery / thali / etc fixed in position complete all as specified and directed.

S & F in repairs kitchen basket fabricated with stainless steel section (SS-304) best quality of size 430mm x 508mm x 300mm for different use such as placing plane plate / disc / cup / saucer / cutlery / thali / etc fixed in position complete all as specified and directed.

M & L for 125mm x 60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., supplied and fixed complete all as specified and directed.

M & L for 105mm x 60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Note : (i) For item to be replaced under repair (day to day complaint) contactors trade man should report to complaint cell daily and take complaint from concren JE and after attending complaint he should give feedback and return the complaint slip to concern JE in the evening at 17.30 Hrs on same day. (ii) B/R complaint to be attend within 24 Hrs from the receiving of complaint, other wise panalty of Rs.500 per complaint per day will be imposed on contractor. In this regard decision of EIC and GE will full, final and binding to contractor. (iii) Being a maintenance contract site will be handover to contractor as per complaint received from user and as per site requirement. (iv) Rates for above shall be inclusive of rates quoted by contractor against BoQ/Sch 'A'. No extra payment in this regards be made to the contractor.

sanu enterprise

S t modi

Indice Technologies

suvidhiconstruction