REPAIRS TO SEWAGE LINE INCLUDING CLEANING OF SEPTIC TANKS AND SEWAGE LINE MANHOLES DRAIN HARDSTANDING PLINTH PROTECTION PATH BOUNDARY WALL FENCING ETC AND REMOVAL OF VEGETATION FROM BLDGS IN DERA COMPLEX VARSHA VARUNA TARANGINI FERNSONS AND DAWSON VI

Amount

Opening/Lifting of Man hole cover and taking out waste soil,sludge, other sediments, solid waste, and liquid waste from Manhole of any depth and in any condition by pumping or any other mechanical means,and refix the man hole cover on completion of work including taking precautionary and safety measures complete all as specified and as directed Notes:- (a) The night soil, other sediments, solid waste, and liquid waste in any condition removed from manhole shall be taken away from respective vicinities/ Premises on closed containers/conveyance and disposed off out of defence land. The quoted rate shall be inclusive for the same. (b) Disposal of the same shall be the responsibility of the contractor with out any extra expenditure to government. Disposal of waste shall be made in accordance with the regulations of authorities concerned.

Cleaning by roding or with bamboo and taking out waste soil , silt, sludge and other foregin materials from sewage lines/effluent drains below /above GL of any dia of pipe ,removed all waste in sealed container as mentioned in item No 1 above including taking precautionary and safety measures complete all as specified and as directed

Labour only for removing blockage of WC Indian/Europen type urinal/bath or kitchen traps including cleaning of WC pan/floor traps/Nahani traps and removing blockage of down take pipes up to 1st manholes complete all as specified and directed

Cleaning of culverts and covered drains of any depth/width after removal of RCC cover slab and refixing the same in position after cleaning and removal of silt to a distance exceeding 100m and not exceeding 1500m complete all as specified and directed Note: 1.Cleaning to be done pre monsoon and post monsoon as per site requirement and shall be measured seperatly all as specified and as directed by Engineer In Charge. 2.Removing and refixing of drain cover and setting in CM 1:4 shall be inclusive of the quoted rate

Pumping out sewage water from the man holes / septic tank / soakage well at different locations by means of sewage tanker fitted with pump (5000 ltrs capacity) and disposing outside MD land as directed by Engr-in-charge .

Pumping out sewage water from the man holes / septic tank / soakage well at different locations by means of sewage tanker fitted with pump (exceeding 5000 ltr not exceeding 20000 litres capacity) and disposing outside MD land as directed by Engr-in-charge . Notes:-(For ser item No.1 to 6 above) (i) Contractor's supervisor has to collect complaint slip from AGE B/R-I office on all working days. The complaints has to be attended and submit the slip duly signed by the user on the same day by 1700 hrs to the Office. (ii) If the contractor fail to attend the complaint, recovery @ Rs. 500 per day per complaint shall be effected from the amount due to the contractor. (iii) If there is any major blockage in sewage line/Septic tank or any emergency situation, immediate service has to be provided by the Contractor even in holidays without any extra cost.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or re-fixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed

Supply and fix 110 mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors (jointing to be done with solvent cement) complete as specified and directed

Supply and fix 110 mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to wall (jointing to be done with solvent cement) with and including clamps complete as specified and directed

Supply and fix 75mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to wall (jointing to be done with solvent cement) with and including clamps complete as specified and directed

Supply and fix 110 mm dia PVC (SWR) bends any radius complete all as specified and directed

Supply and fix 75 mm dia PVC (SWR) bends any radius complete all as specified and directed

Supply and fix PVC (SWR) junction single (Single T) 110mm bore equal or unequal complete all as specified and as directed

Supply and fix PVC (SWR) junction single (Single T) 75mm bore equal or unequal complete all as specified and as directed

Supply and fix in repairs 75 mm dia PVC (SWR) vent cowl complete all as specified and directed

Demolition of brick work, stone / boulder / PCC block masonry built in cement or cement lime mortar complete all as specified and directed

Material and labour for precast cement concrete block masonary with solid blocks exceeding 10 cm width type C1 1:3:6 using 20mm graded stone aggregate set in CM 1:6, complete all as specified and directed

Taking down cement plaster on brick or stone wall surface etc including raking out joints ,hacking for key, scrubbing down with water etc complete all as specified and directed

Material and labour for rendering 15mm thick with CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed

Material and labour for applying 2 or more coats of 100% premium acrylic emulsion paint having VOC less than 50g/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance, exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10Sqm over and including priming coat of exterior primer applied at 0.90 litre/10 Sqm over new surfaces complete all as specified and directed

Material and labour for complete removal of existing treatment and washing ,rubbing down surfaces of walls at any storey of buildings and applying two coats 100% premium acrylic emulsion paint having VOC less than 50g/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance, exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10Sqm over and including priming coat of exterior primer applied at 0.90 litre/10 Sqm complete all as specified and directed

Material and labour for preparation of old external surfaces of wall and applying one coat of exterior premium acrylic emulsion paint, alkali and fungal resistance, dirt resistance, exterior paint of required shade complete all as specified and directed

Material and labour for preparation of old decorated surfaces of walls (plastered or un-plastered) including cornices and applying one coat of cement base paint complete all as specified and as directed

Demolition of concrete in ground floors and pavings n exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Material and labour for Plain Cement Concrete 1:4:8 (Type D2) using 40mm graded stone aggregate as in foundations, filling and mass concrete, sub base or levelling course of floor complete all as specified and directed

Material and labour for plain cement concrete 1:3:6 type C2, (40mm graded stone aggregate) 100 mm thick as in path finished the surface even and fair without using extra cement complete all as specified and directed

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed

Material and labour for cement concrete ( 1:3:6 ) type C1 (using 20 mm graded stone aggregate) as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement and necessary form work complete all as specified and directed (Note : Forming fair finished channel for drain using extra cement will be measured and paid seperately.)

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed

Dismantling fencing wire mesh, any type including mild steel deformed bars in any size complete all as specified and as directed

Dismantling posts or struts from natural ground (wood, steel, or RCC) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed

Excavating in post holes each n.exc. 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed earth around, in layers n.exc.25cm in soft/loose soil and removing surplus soil to a distance not exceeding 50m complete all as specified and as directed

Supply and fix MS posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc; and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed

Material and labour for Plain Cement Concrete 1:3:6 (Type C-2) using 40mm graded stone aggregate as in foundations, filling and mass concrete, complete all as specified and directed

Supply and fix in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ingbolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured) complete all as specified and directed

Supply and fixing MS galvanised chain link fencing of grid size 50x50x3.10mm dia wire (Weight not less than 3.25 Kg/Sqm including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed

Material and labour for mild steel round bars 10mm dia and over cut to length, bent to shap required including cranking, bending spirally for hooping for as in line wire for straining fencing and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

Supply and fix framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete qulity A complete all as specified and as directed

Supply and fix framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

Dismantling plain or corrugated steel/ AC sheeting any gauge, thickness complete in roofing complete all as specified and directed

Supply and fix rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or other connecting plates complete all as specified and directed

Supply and fix prepainted galvalume zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified and as directed

Supply and fix prepainted galvalume zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to rain water gutters fixed with self tapping screws complete all as specified and as directed.

Material and labour for running welding in repairs n.exc 6mm thickness of metal including cleaning and preparing the steel surfaces to be welded together, holding the members like windows, railings, guard bars etc. in true position while welding and bevelling of edges, as required complete all as specified and directed

Material and labour for welding in repairs exc 2.5cm but n.exc 5cm in length of welding and n.exc 6mm thickness of metal including cleaning and preparing the steel surfaces to be welded together, holding the members like windows, railings, guard bars etc. in true position while welding and bevelling of edges, as required complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description exceeding 10cm width or girth and applying two coat of anticorrosive paint over a coat of appropriate primer complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

Material and labour for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments including screed bed or beddding layer in 1:6 cement mortar 20mm thick for laying floor finishes including dismantling of old tile complete all as specified and directed Note: Quoted rate shall be inclusive of screed bed

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed

Material and labour for Machine pressed precast concrete interlocking paver block any shape and size as approved conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment,over and including provision of 30mm thick coarse aggregate for granolithic floors graded from 12.5mm to 4.75mm Spreading and levelling in layers n exc. 25cm thick and well ramming including watering as required complete all as specified and as directed

Material and labour for Machine pressed precast concrete interlocking paver block any shape and size as approved conforming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigment,over and including provision of 30mm thick coarse aggregate for granolithic floors graded from 12.5mm to 4.75mm Spreading and levelling in layers n exc. 25cm thick and well ramming including watering as required complete all as specified and as directed

All as per item No.51 above except paver block (60mm thick) complete all as specified and as directed Note: Serviceable Paver block obtained under item No 50 shall be re used under this item. Quoted rate shall be inclusive of 30mm thick coarse aggregate for granolithic floors graded from 12.5 to 4.75mm .

Material and labour for TMT (MS) bars 6 to 10mm dia cut to length bent to shape required including cranking, bending spirally for hooping column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed

Material and labour for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in landings, cover slabs (for manholes etc) chullah hoods, chajjas,water troughs,mangers, shelvesand similar articles with plain faces set in CM 1:4 including necessary formwork complete all as specified and as directed Note: Reinforcement shall be measured and paid seperately

Material and labour for 18-20mm thick machine cut polished 1st quality granite slab (of any type) work (table rubbed and polished) for wall lining (veneering to wall) and gate pillars 12mm thick in cement mortar(1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including a backing coat of 12mm thick cement plaster in 1:3 complete all as specified and directed Note: Quoted rate shall be inclusive of backing coat

Excavating in trenches not exceeding 1.5 m wide and n exc 1.5 m in depth; for foundation,manholes etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) of internal dia 150mm set in cement mortar complete all as specified and directed

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) of internal dia 100mm set in cement mortar complete all as specified and directed

Supply and fix 150 mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches complete as specified and directed

Material and labour for plain cement concrete 1:3:6 type C2 (using 40mm graded agg) as in bed to drain pipe, 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested including necessary shuttering and supports to concrete complete all as specified and as directed

Material and labour for plain cement concrete 1:3:6 type C2 (using 40mm graded agg) as in bed to drain pipe, 110mm bore including packing under and haunching against the sides of pipes after they are laid and tested including necessary shuttering and supports to concrete complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in soft/loose soil complete all as specified and as directed

Removing excavated material (soils) not exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed

S A ENTERPRISES (BID ID -3368703)

S&C ENTERPRISES (BID ID -3361021)

Oriental Constructions (BID ID -3360241)

Anaswara Constructions (BID ID -3361228)