SPL REPAIR TO BLDG NO. T-29 (SINGLE OFFRS LIVING ACCN) OF 51 MED REGT AND 03 X BATHROOM BLOCK (BLDG NO. T-40, T-38, T-55) OF 19 WEU (MIL STN THAKURBARI) UNDER GE (N) TEZPUR

Note 1: (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

S&F in repair Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 m

S&F of LED bulb 9 w high sutable for lamp holder complete complete all as specified and as directed by the Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal /square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut,length of bolt exc 5cm but n exc 10cm long dia of shank 5 to 10 mm including dismantling of existing surface complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of radius 110mm bore complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4) type B1 (20mm graded stone aggregate) as in floor finished rough to receive floor finishes including dismantling of existing surface complete all as specified and directed.

S&F MS steel work in (MS round/square/rectangular pipe,angle) posts,truss ,purlin and water tank stagging including special shaped washers etc., complete using but welded tubes confirming to IS 1161- 1979 graded St 240 with one shop coat of zinc chromate primer paint including dismantling of existing surface complete all as specified and directed.

S&F 4 mm thick Non asbestos fibre cement building board decorative type( e-board) fixed in aluminium snap grid frame work with screws complete all as specified and as directed.

M&L for non skid ceramic (coloured) tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 15mm thick screed bed in CM 1:6 including dismantling of existing surface complete all as specified and directed.

M&L for non skid ceramic (coloured) tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 40mm thick hard wood planed at both sides boarding as in joist of ceiling, rafters, truss and members including taking down existing surface complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 including dismantling of existing surface complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of radius 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of radius 75mm bore complete all as specified and directed.

Material and labour for rendering 15mm thick cement plaster in cement mortar (1:6) on unfair faces of brickworks complete all as specified and directed.

M&L for 75 mm 1:3:6 type C2 ( using 40 mm graded stone aggregate) as plinth protection/paving finish even and smooth without using extra cement including dismantling of existing surface complete all as specified and directed.

ditto as item no 53 above but without glazing bars complete all as specified and as directed.

M&L for TMT bars, 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally, hooping for columns, hookings/ends and binding with and including MS wire not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling framed timber scantlings 40 sq. cm & over in section, in any position complete all as specified and as directed.

M&L for 2 nd class hard wood scantling wrought finished in any position over and 40 sq. cm & over in section,complete all as specified and directed.

S&F for second class hardwood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube etc complete all as specified and directed.

S&F Butt hinges 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F PVC (SWR) bends of radius 110mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

S&F 110mm dia PVC(SWR) junction single, (single T) equal or unequal with access door complete all as specified and as directed.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement as in repair complete all as specified and directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for PCC 1:3:6 type C1 as in concrete bed to drain pipe incl packing under haunching against the sides of pipes after are laid and tested for 110mm dia pipe complete all as specified and directed.

S&F for 150 mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe internal dia 100mm and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required as directed by Engineer-in-Charge

M&L for applying two coat of cement based paint on new surface including preparation of surface incl Priming plastered and other surfaces with alkali resistant priming paint complete all as directed.

M&L for applying two coat of White Wash on new surface including preparation of surface incl Priming plastered and other surfaces with alkali resistant priming paint complete all as directed.

M&L for applying one coat of cement based paint paint on old surface including preparation of surface complete all as specified incl Priming plastered and other surfaces with alkali resistant priming paint complete all as directed.

M&L rendering 5 mm thick in cement plaster in cement mortar (1:4) mixed with integral water proofing compound @3%by wt of cement over 10 mm thick backing coat in cm (1:4) on fair faces of brick work or concrete surface complete all as specified and directed. Note : water proofing compound shall be measured and paid separately).

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'B' complete all as specified and as directed.

M&L for Preparation of new plastered surfaces and applying two coats of OBD over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new plaster surface of walls etc and applying two coats of acrylic washable distemper over 1 mm thick wall care putty in two coats over a coat of primer (smooth bodied opaque finish surface) complete all as specified and directed.

M&L for preparing of surfaces of walls by complete removal of existing treatment and applying two coats of acrylic washable distemper over 1mm thick wall care putty in two coats over a coat of primer (smooth bodied opaque finish surface) complete all as specified and directed.

cket outlet three pin 15 amps control by one switch independent board with cable 2.5 sqmm size (two run) & 1.5sqmm (one run) complete all as specified and directed.

Dismantling existing water tanks capacity exc. 500 Ltrs but n.exc 1000 Ltrs, removing from site complete all as specified and directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete as as specified and directed.

Material and labour for preparation of new and previously un-treated steel surfaces of any description, not otherwise described over 10cmwidth or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F 25mm outer diameter of PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed.

S&F wash down water closet (pedestal pan) including connection to drain pipes and to flushing pipes anti-syphonage pipe etc excluding flushing cistern incl flush pipe, jet and seat cover complete as as specified and directed

(a) One light point controlled by one switch

(b) One fan point controlled by one switch

(c) One 3 pin socket outlet 5 amps on the same board controlled by one switch.

(d ) One 3 pin socket outlet 5 amps on independent board controlled by one switch.

(e) One so

S&F switch piano flush type 5 amps single pole one way complete all as specified and directed by Engr-in Charge

S&F switch piano flush type 15 amps single pole one way complete all as specified and directed by Engr-in Charge

S&F socket outlet 3 pin, 15 Amp, flush type complete all as specified and directed by Engr-in Charge

S&F switch piano flush type 5 amps single pole one way complete all as specified and directed by Engr-in Charge

S&F socket outlet 2 in 1, 3pin 5 amps 230 volts complete all as specified and directed by Engr-in Charge

S&F ceiling rose , polycarbonate, isolated body with 2 to 3 terminals complete all as specified and directed by Engr-in Charge

S&F Electronic fan regulator dimmer type,450w , 250 volt complete all as specified and directed by Engr-in Charge

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Five star rated with brushless direct current motor complete and old fan deposit to E/M yard complete

S&F lamp holder insulated body with back plate for batten fittings/angle holder as required and including taking down old damaged holder.

S&F Chromium plated shower roses 125mm size of Std quality and approved make with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F of LED bulb 9 w high sutable for lamp holder complete complete all as specified and as directed by the Engineer-in-Charge.

S&F for 2000 Ltr capacity rotational moulded polythelene, three layer, PVC water storage tanks (cylindrical or vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Taking up or down steel tubing and connections, 15/20/25 mm bore and removal of unserviceable pipe from site of work complete all directed.

S&F sub main wiring complete with two runs of 4 sqmm PVC insulated unsheathed single core multistrand copper conductor cable of 1100 volts grade drawn through new non metalic rigid PVC casing capping on wall alongwith accessories fixed on wallS&Floors/ceiling with one run of 4 sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor all as specified and directed by Engr-in-Charge. Note:- Two runs of PVC insulated cable 4 sqmm + one run 4 sqmm of earth wire and one run of conduit including accessories shall be measured as one length including taking down existing sub main wiring complete all as specified and directed.

Supply and fix 20Watts LED light fitting, basic all purpose surface and wall mounted LED batten 20Watts with aluminium housing and integrated electronic driver including 20W LED tube - 1No. all as per Cat No.LTTB4F20WLED/W of C&S or equivalent of other specified makes fixed on surfaces of wall or ceiling including taking down the old fitting all as specified and as directed by the Engineer-in-Charge.

S&F of LED bulb 9 w high sutable for lamp holder complete complete all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring of size 1.5 sqmm (two run) with PVC insulated unsheathed multistranded copper conductor cabel of 1100V grade drawn through PVC casing & caping minimum size 20 mm including accessories, fixed on surfaces of wall/floor and fixed on ceiling/roof etc, including pressed steel terminal boxes 1.6 mm thick, concealed in walls with plastic laminated sheet cover 3mm thick as top cover fixed with cadmium screws for housing the switchs,sockets, fan regulators etc., incl provn of 1.5 sqmm PVC insulated copper earth conductor cable for earth continuity and connecting to common earth dolly including taking down old point wiring all as specified and directed by Engr-in-Charge.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F lamp holder insulated body with back plate for batten fittings/angle holder as required and including taking down old damaged holder all as specified and as directed by the Engineer-in-Charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete and old fan deposit to E/M yard all as specified and as directed by the Engineer-in-Charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, 5 Star rated with all accessories such as safety valve, thermostate, NRV, PVC connection pipe ccomplete and old geyser deposit to E/M yard all as specified and as directed by the Engineer-in-Charge.

S&F Sheet metal enclosure of single pole and neutral enclosure with a Two pin and earth plug and socket complete with one MCB of 20Amps.including taking down the old fitting all as specified and as directed by the Engineer-in-Charge.

Supply & Lay underground XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of of size 10 sqmm 2 core complete all as specified and directed by Engr-in Charge . Note :- Including nacessary excavation and clamp on wall with proper screw complete

Earthing complete with galvanised steel earth plate electrode 60cm x 60 cm x 6.3 mm thick burried directly in ground vertically to a depth not less than 2.25m deep below ground level with top edge of plate not less than 1.5 below ground level connected to GI 4mm earth wire by means of bolts, nuts check nuts washers made of galvanised iron or steel earth wire protected by GI pipe 15 mm bore light grade connected upto switch board incl 20mm bore GI water pipe with funnel and wire mesh all as shown in electrical plate No.3 of SSR Part I including dearth chamber of PCC 1:2:4 type B1 using 20mm grade aggregate with RCC cover slab 1:2:4 type B1, 40mm thick with 15mm dia MS bar 100mm C/C both ways and 6 MM dia MS hooks complete all as specified inlcuding testing on completion.