KYIP ACP NP 2020 21 Rectification of canal shutter of Perumundassery Distributary and canal shutters at various chainages of Thiruvallur Distributary Mechanical work

Amount

Dismantling the shutter and hoist unit ,chipping concreting the groove and convey the scrap materials to nearest custodian office . Cost includes of labors, hire charge of tools , conveyance, loading and unloading charges etc. complete

od29609/2020_2021/MH : Dismantling of the Canal Shutter ( up to 2 Tonne weight ) /Hoist bridge /Embedded parts etc.of the same and stacking at distance of 100m including hire of machinery labour etc. complete as direct by the departmental officer at the site (weight of unserviceable shutters and embedded parts may be calculated as 60% unserviceable hoisting unit as 80%)

od32321/2020_2021/MH : Chipping the groove including cost of materials,conveyance, hire charge ,labour and other incidential charges complete

15.1 : Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres lead as per direction of Engineer - in- Charges.

4.3.3 : Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts

4.4.1 : Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size)

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Supply , Fabrication of MS material for Embeded parts

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od30233/2020_2021/MH : Fabrication and Erection of Embedded parts of Canal gate (up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

Supply of materials, fabrication,painting and erection of MS shutter

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od30231/2020_2021/MH : Fabrication and supply of Structural steel canal shutters ( up to 2 tonne weight )/hoist bridge/platform and accessories etc for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

Erection of the shutters safely in the grooves , assembling and aligning

od30234/2020_2021/MH : Erection of the Canal Shutter ( up to 2 Tonne weight )/hoist bridge/platform including hand rails , ladder etc for same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

Supplying and fixing of flat type rubber seal at the bottom side the shutter

85.116 : Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

Supply of materials, fabrication,painting and erection of hoisting bridge and hoist units, screw rod for shutter

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

od27267/2020_2021/MH : Supply of MS Bolts and Nuts

od30235/2020_2021/MH : Fabrication and supply of Structural steel canal shutters ( up to 2 tonne weight )/hoist bridge/platform and accessories etc for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning

85.115 : Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

:Providing worm and pinion, base and nut arrangement,rollers for hoisting the shutter. including cost of all materials labour hire charges of machinery, industrial charges etc complete

od30236/2020_2021/MH : Providing base and nut arrangement for hoisting the shutter including cost of all materials labour etc complete

od33578/2020_2021/MH : operating handle for base and nut , cost include cost of mateials ,making, suply ,conveyance, labour etc

od33595/2020_2021/MH : Providing of worm and pinion having a lift speed of round 5.00cm/min for hand operation operation including cost of all material ,labour,hire charge and conveyance

od33600/2020_2021/MH : Supplying and fixing cast steel thrust roller assembly having 100mm Dia, 50mm tread width, SS(304) shaft bush and accessories as per approved specifications and drawings including cost of all materials, machineries, labour , all lift and lead, incidental and conveyance charges etc complete

Supply and fabrication of Screw rod

od32445/2020_2021/MH : Providing EN-8 screw rod 7.5 tonne capacity 4.00M lift screw hoist having one number of EN-8 Screw shaft having a lifting spead of around 5.00 cm/min for 24rpmof hand operation including cost of all material,labour,hire charges and conveyance

Erection of the hoisting bridge and units including Screw rod, base and nut etc

od30238/2020_2021/MH : Erection of the Canal Shutter ( up to 2 Tonne weight )/hoist bridge/platform including hand rails , ladder etc for same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

Providing Sluice Valve and DI Pipe for Payangottayi Filed Channel ch: 5/065

od32218/2020_2021/MH : Dismantling existing damaged 200mm dia Cement Pipe hire charge ,labour and other incidental charges complete

od32215/2020_2021/MH : Fixing U - Clamp for Pipes. Cost includes cost of all materials, labour charges & conveyance complete.

18.31.6.2 : Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately):300 mm diameterClass II

18.73.5 : Providing and laying Double Flanged ( Screwed / Welded ) Centrifugally (Spun) Ductile Iron Pipes of Class K - 9 conforming to IS: 8329 :300 mm dia Ductile Iron Double Flanged

18.30.6 : Providing flanged joints to double flanged C.I./ D.I pipes and specials, including testing of joints:250 mm diameter pipe

PEETHAMBARAN

Bidder Name

P.Damodaran, G.R.Industries

PEETHAMBARAN