S.R. to Court building at Sankheda Ta. Sankheda Dist. Chhotaudepur (Repairing of Compound wall, Colour work, Toilet block, Plumbing work & Electrification)

No. figures

1 Removing and scraping of old deteriorated plaster of any thickness 602.00 Sq.m. 20.36

from wall / R.C.C member including stacking of serviceable material

and disposal of unserviceable from site of work with all lead and lift.

2 Demolition of brick work and stone masonry including stacking of 24.00 Cum 576.30

serviceable materials and disposal of unserviceable materials with all

lead and lift. (ii) In Cement Mortar.

3 Dismentaling tiled of stone floors laid in mortar including stacking of 524.00 Sq.m. 50.28

serviceable materials and disposal of unserviceable materials with all

lead and lift.

4 Dismentaling doors, windows, ventilators etc. (wood or steel) shutters 39.00 No. 196.66

including chowkhats architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift. (i) Not exceeding

3.00 Sq.m. in area.

5 Providing and laying brick work using common burnt clay building 37.00 Cum 4568.40

conventional type bricks having crushing strength not less than

Kg./Sq.cm. in foundation and plinth in cement mortar 1:6 (1 cement :

6 fine sand) including the cost of all materials and labour charges etc.

6 Providing 15 mm thick cement plaster in single coat on fair side of 847.00 Sq.m. 253.61

brick / concrete walls for interior plastering upto floor two level finished

even and smooth in cement mortar 1:3 (1 cement : 3 sand) finishing

with a floating coat of neat cement slurry including making groove

interior plastering above floor two level for Ground floor.

7 Providing and fixing Door of factory made & stamped I.S. 12823 grade 42.00 Sq.m. 3975.36

one, type one 35 mm thick solid core, melamine faced, three layered

resin, flushed door, having decorative lamination on both side including

30 cm long stainless steel pipe handle on both side SS ASIS

Grade, SS stopper 20 cm, SS Aldrop 30 cm both side, SS hinges

Nos. in each shutter & fixtures & fastenings as directed by Engineer in

charge etc. complete.

8 Providing and fixing window having extruded aluminum colour 18.00 Sq.m. 1583.95

anodized section frame main outer size 95mm x 24mm x 1.17mm (@

wt. of 0.738 kg/mt), horizontal three track member size 92mm x

31.75mm x 1.30mm (@ wt. of 1.07 Kg/mt), vertical member of size

92mm x 31.75mm x 1.50mm (@ wt. of 1.06 Kg/mt) with sliding

shutters of horizontal member size 40mm x 18mm x 1.29mm (@ wt. of

0.456 Kg/mt), vertical member of size 40mm x 18mm x 1.29mm (@ wt.

of 0.456 Kg/mt) with 5 mm thick transparent bronze colour tinted float

glass with powder coated alluminium fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details etc.

9 Providing and fixing standard extruded of Aluminium section of size 4.00 Sq.m. 1175.56

63mm x 38.10 mm x 1.2mm (@wt. 0.643 Kg/mt.) with colour anodized

alluminium frame for ventilation with 5 mm thick frosted glass as

details etc. complete for Ventilation as directed by Engineer in charge.

It. Rate in

Description of Item Qty. Unit Amount

No. figures

10 Painting two coats (excluding priming coat) on new steel and other 21.00 Sq.m. 94.39

metal surface with enamel paint, brushing, interior to give an even

shade including cleaning the surface of all dirt, dust and other foreign

11 Finishing wall with weather proof exterior emulsion paint on wall 847.00 Sq.m. 122.14

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt and remains of loose

powdered materials etc. complete for all heights.

12 Providing and laying broken china mosaic flooring for terrace using 550.00 Sq.m. 779.70

12 mm to 20 mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar creme

out upto surface using white cement including rounding off junctions

and extending them upto 15 cm along the wall, clearing with water and

oxalic acid etc. as directed.

13 Supplying and erecting approved make of tube fitting with one no. T-5 13.00 Each 480.76

tube 24/28 W with Electronic ballast with each tube separately THD

less than 10 & built in adeptors, GI / PVC housing & mirror optic

reflector, suitable to work on 120V - 300V, A.C. supply with connector

and adapter if required. [Make of fitting & tube may be differ & fitting

shall be providing with tube].

14 Providing and erecting heavy duty flood light integral luminaire 6.00 Each 2311.89

comprises die cast alluminium body with heat resistant toughened front

glass, silicon rubber gasket, anodized reflector hot deep powder

coated cradle clamp with suitable size of necessary built in control gear

complete with lamp.

15 Providing and erecting approved make Ceiling fan with double ball 4.00 Each 2311.89

bearing ISI mark with Condenser 230 volt A.C., 50 Hz 1200mm sweep

complete having 3 blades alluminium body and blade sets having

ornamental design shanks, canopy erected with earthing. [Make shall

be approved by Engineer in charge].

16 Providing and fixing Table top wash basin with pillar cock, chromium 4.00 No. 4584.39

plated, bottle trap and waste pipe, necessary couplings of approved

quality for wash basin.

17 Providing and fixing chromium plated flush cock of approved quality 8.00 Each 225.97

including fixing in pipe line etc. complete. (ii) 25mm dia. as directed by

Engineer in charge.

18 Providing and fixing C.P. brass screw down stop cock of approved 8.00 Each 189.16

quality of 25mm dia. as approved by Engineer in charge with

adjustable wall flange.

19 Providing and fixing screw down bib taps of following size (B) brass 16.00 Each 214.81

chromium plated screw down bib tap (ii) 20mm dia. as directed by

Engineer in charge.

20 Providing, laying and jointing in true line and level I.S.I. mark 40 mm 10.00 Rmt. 148.12

dia. U.P.V.C. pipe (SCH- 40) for cold water including fittings as

approved by Engineer in charge. Pipe shall be fixed on the wall with

the help of clamp at every two metre C/C or shall be concealed as

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent including cost of all

materials. 40mm dia.

It. Rate in

Description of Item Qty. Unit Amount

No. figures

21 Providing, laying and jointing in true line and level I.S.I. mark 50 mm 14.00 Rmt. 195.67

dia. U.P.V.C. pipe (SCH- 40) for cold water including fittings as

approved by Engineer in charge. Pipe shall be fixed on the wall with

the help of clamp at every two metre C/C or shall be concealed as

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent including cost of all

materials. 50mm dia.

22 Providing, laying and jointing in true line and level I.S.I. mark 110 25.00 Rmt. 897.79

diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end

plain and other end socketed with rubber ring, & fittings conforming to

ISI 14735-1999 of approved make for drainage system pipe line, pipe

shall be jointed with each other with rubber lubricant, pipe shall be

fixed on wall using of PVC clamp of the size 110 mm diametre x

mm length x 145 mm height at every 2000 mm center to center or shall

be concealed in walls as directed including necessary fittings such as

bends, shoes etc. including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

Total Rs.

i.e. Rs. Twelve lacs Fifty Nine thousand Five hundred Twenty and Seventy Five paisa only.

I/We am/are willing to carry out the work @ _______ __ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

Net Rs. ___________________________ Total Rs. ____________________

In words ____________________ In words ____________________

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-

In-Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

5. Credit for dismantalled materials of amount of Rs. 5000.00 must be recovered from 1st R.A. bill of

Contractor's.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me

and found order.

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Bodeli (R & B) Sub Division, Chhotaudepur (R & B) Division, Chhotaudepur (R & B) Division,

Bodeli Chhotaudepur Chhotaudepur