AMRUT-Providing drinking water KIOSK in Nehru Trophy ward Alappuzha municipality General Civil Work

Amount

APPENDIX .A - AMRUT - Construction of building for providing 1 no drinking water KIOSK at Nehru trophy ward in Alappuzha municipality

2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

50.2.26.1:Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.22.1:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelMild steel and Medium Tensile steel bars

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.8:Providing non- asbestos high impact Polypropylene reinforced cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J or L hooks, bolts and nuts, 8 mm dia G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafter and trusses), including cutting sheets to size and shape wherever required.

12.4.1:Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.80 mm thick with zinc coating not less than 275 gm/m2

OD125969/2022-2023:Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.<br>75 mm overall thickness partition with bison board

11.47.1:Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 500x500 mm

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.1:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium ( anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

21.17:Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment ).

9.119:Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door fame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer-in Charge.

9.120.1:Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and sized of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of whicj 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5mm thick, 95 mm wide PVC sheet out of which75 mm shall be tapered in 45 degree on th inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mmx2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded /sealed to the styles & rails with 7 mm (5 mm + 2 mm ) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer -in-charge, manufacture's specification & drawing.30 mm thick plain PVC door shutters

25.7:Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.47.1:Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

100.60.14.2.2:Providing 20mm (3/4 inch) house connection with 20mm water meter from existing PVC / HDPE mains from 140mm to 200mm dia., up to a length of 5 m using 25mm ( 3/4 inch ) PE Pipe, PE80, PN16, Conforming to IS 4984: 2016 or later edition and PP PN 16 Compression / GM / Brass specials viz. brass ferrule, brass hexagonal nipple, GM full way wheel valve, bend, MTA, FTA, couplers, PVC Service Saddle of suitable size etc. and connecting with the mains, testing the joints etc. complete including trenching and refilling in all kinds of soil up to a depth of 1.50m for main line tracing and trench of average cross section 0.3m x 0.75m for laying connection pipe and service pipe, fixing water meter, lighting, watching, providing caution boards, traffic control etc. complete including cost of materials, hire for tools, cost of consumables and labour charges, including the cost of tested Class B Multijet water meter with ISI mark and weather resistant PP / PE meter box of minimum size 300mm x 200mm x 150mm, but excluding charges for cutting the concrete / tarred / bituminous roads etc, and as per the direction of the departmental officers.

100.60.15.2.2:Providing additional length of house connection pipe using 25 mm (3/4 inch) PE Pipe, PE80, PN16, Conforming to IS 4984: 2016 or later edition and PN 16 specials and testing the joints etc., by trenching and refilling in all kinds of soil with trench of average cross section 0.3m x 0.75m for laying of connection pipe and service pipe, lighting, watching, providing caution boards, traffic control etc., hire for tools, cost of consumables and labour charges etc. complete, but excluding the cost of cutting of concrete / tarred / bituminous roads, and excluding cost of materials etc., and as per the directions of the department officers.

OD125971/2022-2023:2+4 way SPN single door MCB<br>

OD125972/2022-2023:40Amps rating 2 pole RCCB 100MA/300MA<br>

OD125973/2022-2023:40Amps, 2pole isolator<br>

OD125974/2022-2023:Wiring for light /power plug with 2x4 sqmm FRLS PVC insulated copper conductor single core cable in surface recessed steel conduit along with 1no 4sqmm PRLS pvc insulated copper conductor. Single core cable for loop earthing as required<br>

OD125975/2022-2023:Wiring for llight point/fan point/exhoust fan point /call bell point with 1.5 sqmm FRLVS pvc insulatedcopper conductor single core cable in surface recessed steel conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5sqmm FRLS pvc insulated copper conductor single core cable etc. as required<br>

OD125976/2022-2023:supplying and fixing 25mm multijet ,Indian standard water meter

OD125977/2022-2023:supply 32mm flexible section hose

APPENDIX .B-RO Plant water Purifier System

OD125968/2022-2023:Supply of water treatment plant Reverse Osmosis system capable of removing TDS, fluoride etc: protected drinking water having constantly out put capacity of 1000 liter/hrs., operating pressure 5 to 10 Kg/cm2 and operating tempeature 25oC to 40o C. The system will be capable of treating of raw water having TDS up to 3000 PPM and fluoride up to 10 PPM and beyond the corresponding treated water will confirm to ISS drinking water standared IS 10500/1991 and packaged drinking water standard IS 14543 of approved Make. The system will have the following essential components.<br>1. Raw Water Pump-1 No. Horizontal Centifugal type with flow rate not less than 1000 litres per hour, head 50m, operating at 220V<br>2. Dual media filter-1 No.- Vessel constructed of best quality FRP,having diameter 10 inches, height 54inches, having opening at the top, testing pressure 10kg/cm2, having valve made of high strength PP white , with multiport, with maximum flow rate 1500LPH, working pressure 2 - 4 Bar with mixed bed sand media consisting of Graded silex. Quartz Sand and premium Anthracite <br>3. Activated carbon filter Vessel 1 No. constructed of best quality FRP, having diameter 10 inches, height 54inches, and opening at the top, fitted with valve of size 1 inch with multiport made of high strength PF white, with maximum flow rate 1500LPH at working pressure 2 to 4 bar, containing Mixed bed sand media consisting of Pebble, Quartz sand, activated carbon of IV 1050 ;Pipe lines and accessories : pipe of PVC 10 bar tested pressure, testing cock & pressure gauge at inlet – outlet of system with pipe of PVC 10 bar tested pressure, testing cock & pressure gauge at inlet – outlet of system<br>4. Dosing system constructed of PP, having capacity 5 litres per hour and pressure 4 bar<br>5. Reverse osmosis membrane spiral wounded type of diameter 4 inches, length 1m, with system recovery of 60% max.<br>6. Micron filter made of PP white, of length 20 inches, diameter 4 inches, with cartridge made of poly propylene,of length 20 inches, diameter 2.5 inches and having micron rating 5 Microns.<br>7. Reverse osmosis pressure tube constructed of FRP, with pressure vessel of diameter 4 inches, and length 1.1m with 12 membranes per vessel, with 1 No. Array<br>8. High pressure pump made of stainless steel, vertical multistage type, having flow rate 100 litres per hour, and head 140m, operating at 230V AC, at 29000rpm<br>9. Micro processor controlled display panel with Complete starters, overload relays, MCB ‘s indicating light, Push buttons, Rocker switches for dosers, Incomers, Auto-manual switches, TDS display ets complete<br>10. Instrumention system on common stainless steel, complete with flow meter- 2Nos., with high flow pressure switch -2 Nos, pressure gauge- 2 Nos., and NRV ‘s pressure relief valves where ever needed <br>11. Float switches or automatic cut off-2 Nos., SS tank 1000 lire( treated water tank)-1 No., HDPE tank 1000 litre( raw water tank)-1 No., Ultra violet disinfections system 2000LPH-1 No., Dispensing tap bank with UPVC plumbing lines-2 Nos.<br>

APPENDIX.D.Sump tank fixing

100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

18.48:Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

OD125966/2022-2023:Supplying errection ,testing commissioning of automatic water level indicator with necessary sensors connecting using 230 V AC line having necessary cables and switches etc complete

100.98.218:Supply of PVC Pipe, 8kg/cm2, 32mm Dia.

OD125967/2022-2023: Supplying and fixing of 0.5 HP monoblock pumpset including foot valve ,32 mm pvc pipe etc complete

Providing booster pump in drinking water kiosk

OD133910/2022-2023:Supplying 0.5 HP booster pumpset (copper winding with ISI) with accessories(pipe size-2.5x2.5 cm,Head range 6 to 30 m,output 1000 lph@24m

OD133909/2022-2023:Supplying of 32 mm ASTM pipe (SCH-80)

OD133908/2022-2023:Supplying and fixing of 32 mm brass type Non return valave

OD133904/2022-2023: Supplying and fixing of 32mm ASTM tee

OD133903/2022-2023: Supplying and fixing of 32mm ASTM elbow

OD133907/2022-2023:Supplying and fixing of 32mm PVC ball valve

OD133906/2022-2023: Wiring for motor point with 2.5 sqmm FRLVS pvc insulated copper conductor single core cable in surface recessed steel conduit with modular switch, Socket modular plate, suitable GI box and earthing the point with 2.5sqmm FRLS pvc insulated copper conductor single core cable etc. as required<br

OD133905/2022-2023:Wiring for light /power plug with 2.5x4 sqmm FRLS PVC insulated copper conductor single core cable in surface recessed steel conduit along with 1no 4sqmm PRLS pvc insulated copper conductor. Single core cable for loop earthing as required<br>

FLOWMAX WATER

Bidder Name

HYDROXY WATER TECHNOLOGIES PVT. LTD.

FLOWMAX WATER