Building

Name of Work :- New Construction of Community Health Center Hospital at Tarapur, Ta. Tarapur, Dist. Anand.

Memorandum showing items of works to be carried out

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing, driving with hydraulic piling rings with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-350

of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement

but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. ( Length of pile for payment shall be Four Thousand One Hundred Eighty

measured from top of shoe to the bottom of pile cap) : 500mm dia piles Two Rupees And Paise Sixty Only

Providing, driving with hydraulic piling rings with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-350

of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement

but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. ( Length of pile for payment shall be Five Thousand Eight Rupees And Paise

measured from top of shoe to the bottom of pile cap) : 600mm dia piles Nineteen Only

Providing, driving with hydraulic piling rings with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-350

of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement

but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. ( Length of pile for payment shall be Six Thousand One Hundred Seventy Six

measured from top of shoe to the bottom of pile cap) : 750mm dia piles Rupees And Paise Eighty Nine Only

Vertical load testing of pile in accordance with IS 2911 (Part IV ) including installation of loading platform by Kentledge/Anchor piles method

and preparation of pile head or construction of test cap and diamantling of test cap after test etc. complete as per specification & the direction Fifty Five Thousand Three Hundred

4 2.00 of Engineer in charge. Single pile upto 50MT safe capacity. 55319.23 Nineteen Rupees And Paise Twenty PER TEST ₹

Lateral load testing of single pile in accordance with IS Code of practice IS : 2911 (Part IV) for determining safe allowable lateral load on pile: Nineteen Thousand Eight Hundred

5 1.00 Upto 50 tonne capacity pile 19828.72 Twenty Eight Rupees And Paise Seventy PER TEST ₹

Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface

preparation of pile top by removing soil, mud,dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill One Thousand One Hundred Sixty Four

trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in-charge. Rupees And Paise Seventy Three Only

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 One Hundred Twenty Two Rupees And

Meter lead.(A) Loose or soft soi Paise Ninety Four Only

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated One Hundred Thirty Six Rupees And

8 2484.00 stuff upto 50 Meter lead.(A) Loose or soft soil 136.30 CMT ₹

Paise Thirty Only

Filling available excavated earth (excluding rock)in trenches, plinth,sides of foundations etc. in layers not exceeding 20 cm. in depth One Hundred Thirty Six Rupees And

9 3131.00 consolidation each deposited layer by ramming and watering. 136.92 CMT ₹

Paise Ninety Two Only

Filling in plinth with chhara under floors including watering, ramming, consolidating and dressing etc. completed Six Hundred Twenty One Rupees And

Paise Forty Six Only

Filling in foundation and plinth with murrum or selected soil in layers of 20cm thickness including watering ramming and consolidating etc. Two Hundred Ninety Four Rupees And

11 441.00 complete 294.38 CMT ₹

Paise Thirty Eight Only

Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete Four Hundred Eighty One Rupees And

Paise Eighty Only

Applying general insecticide pest control treatment to floors, cupboards etc including labour materials etc. complete. Using Imidacloprid

SCas Per IS 6313 part -II( (0.075% concentration by mass) is recommended 10.5ml chemical diluted with 5 liters of water application 0.5 litre Ninety One Rupees And Paise Sixty

13 1563.00 chemical /Sqm of surface is recommended as per I.S. 91.63 SMT ₹

Providing and laying in position Ready Mixed M-350 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of centering shuttering finishing and excluding the cost of reinforcement

including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without Five Thousand Five Hundred Sixty Eight

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be Rupees And Paise Thirteen Only

maintained) (Cement level 475 kg ) For Pile Cap.

Providing & laying controlled cement concrete M-250 with curing etc. complete incl. the cost of form work but excluding the cost of

Four Thousand Seven Hundred Forty

15 80.00 reinforcement for R.C.C. work for Footings. 4745.43 CMT ₹

Five Rupees And Paise Forty Three Only

Provdg. & laying cement concrete 1:2:4 (1cement:2 corse sand :4 hand broken stone aggregate 20 mm nominal size) and curing complete

Three Thousand Seven Hundred Fifty

16 121.00 including cost of form work in (A) Foundation and plinth 3757.61 CMT ₹

Seven Rupees And Paise Sixty One Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- hand broken stone aggregates 40 mmnominal size) and curing Three Thousand Ninety Five Rupees

complete excluding cost of formwork in (A) Foundation and Plinth And Paise Twenty Five Only

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8- hand broken stone aggregates 40 mm nominal size) and curing

Two Thousand Seven Hundred Sixty

18 221.00 complete excluding cost of formwork in (A) Foundation and Plinth 2769.69 CMT ₹

Nine Rupees And Paise Sixty Nine Only

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm nominal size) laid in one layer Three Hundred Sixty Nine Rupees And

and finished with a floating coat of neat cement. (B) 50mm thick. Paise Thirteen Only

Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) and curing

Four Thousand One Hundred Forty Two

20 5.00 complete excluding cost of formwork and reinforcement for reinforced concrete work in (B) Slabs, landing, shelves, Balconis , Lintels, Beams, 4142.24 CMT ₹

Rupees And Paise Twenty Four Only

Girders and Cantilever upto floor two level.

Providing and laying ordinary cement concrete 1:2:4 (1:cement, 2:coarse sand: 4 graded stone aggregates 20 mm nominal size and curing

Five Thousand Six Hundred Three

21 252.00 complete including the cost of formwork but excluding reinforce for reinforced concrete work in (A) Column & Copping, beam etc. 5603.03 CMT ₹

Rupees And Paise Three Only

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete

including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without Six Thousand Eight Hundred Two

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg ) Rupees And Paise Thirty Five Only

For BEAMS up to 3rd floor level.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete

including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without Eight Thousand Two Hundred Nineteen

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg ) Rupees And Paise Eighty Nine Only

For All Columns, pillars posts and struts up to 3rd floor level.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete

including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without Six Thousand Five Hundred Sixteen

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg ) Rupees And Paise Ninety Five Only

for coping up to 3rd floor level.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete

including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without Seven Thousand Four Hundred Seventy

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg ) Eight Rupees And Paise Sixty Five Only

For Lintel up to 3rd floor level.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete

including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without Seven Thousand One Hundred Sixty

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg ) Two Rupees And Paise Ninety Two Only

For All Chhajja up to 3rd floor level.

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete

Seven Thousand Two Hundred Twenty

27 672.63 including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without 7221.20 CMT ₹

One Rupees And Paise Twenty Only

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg )

for Slab up to 3rd floor level.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete

including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without Six Thousand Eight Hundred Eighty One

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg ) Rupees And Paise Eighty Four Only

for Staircabin up to 3rd floor level.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, including the cost of form work but excluding the cost of reinforcement for reinforced concrete Seven Thousand Four Hundred Eighty

29 47.79 including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without 7488.24 Eight Rupees And Paise Twenty Four CMT ₹

impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per letest gov. GR 380 Kg ) Only

for RCC wall up to 3rd floor level.

Providing and laying Controlled CC road Tri mix M-200 having thickness 100 mm including preparing sub base with providing and fixing

channels of 75 mm as per required level slope and thickness of concrete road leveling of placed concrete with surface vibrators finishing

surface with power floater and trowel light booming on the surface including providing expansion joint by concrete cutter machine and filling

Six Hundred Nine Rupees And Paise

30 1042.00 joint by using color 200 as per manufacturers specifications and making construction joint of 5 mm x 50 mm by using concrete cutter machine 609.82 SMT ₹

Eighty Two Only

etc complete as directed by Engineer in charge.

Providing TMT Bar FE -500D reinforcement virgin steel for R.C.C. work including bending, binding and placing in position complete upto 3rd Seventy Eight Rupees And Paise Thirty

31 749456.03 floor level height 78.34 Kg. ₹

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg/Sq. cm. in cement mortar 1:6 (1 cement :

Four Thousand Five Hundred Thirty

32 996.00 fine sand) below plinth & above Plinth level upto 3rd Floor Level (B) Conventional 4538.48 CMT ₹

Eight Rupees And Paise Forty Eight Only

Half brick masonry in common burnt clay building bricks having crushing strength note less than 35 Kg/Sq. Cm. in cement mortar 1:4 (1 cement

: 4 coarse sand) in super structure above plinth level upto 3rd Floor Level (B) Conventional Six Hundred Ninety Rupees And Paise

Fifty Seven Only

Providing 15 mm thick mala cement plaster on interior brick / concrete work for plastering comprising of base coat of 12 mm thick cement

plaster in cement mortar (1 Cement : 3 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Two Hundred Forty Four Rupees And

34 7447.42 Coarse sand) finished with trovel including scaffolding curing etc. complete. 244.86 SMT ₹

Paise Eighty Six Only

Providing 10 mm. Thick cement plaster in single coat for plastering on ceiling and soffits of stairs and finished even and smooth in : (I) One Hundred Ninety Eight Rupees And

35 3879.53 Cement mortar 1:4 (1 cement : 4 sand) etc. complete. 198.37 SMT ₹

Paise Thirty Seven Only

20 mm thick sand faced cement plaster (Gutaka) on walls up to 3rd floor level above ground level consisting of 12 mm thick backing coat of CM Three Hundred Sixty Four Rupees And

1:3 (1 cement : 3 sand) and 8 mm thick finishing coat of CM 1:1 (1 cement : 1 sand) etc. complete. Paise Twenty Three Only

Providing throating or plaster drip and moulding to R.C.C. chhajja Forty Three Rupees And Paise Five

Providing & Fixing the Chikenmesh - 20 guage(Crimp Jali) of approved size applying between the RCC and masonry junction in proper line, level

and plumb with all material, labour, tools, tackles and equipment. Including providing and fixing the jali with nails, etc complete as directed by Two Hundred Ninety Seven Rupees

the site-in-charge. And Paise Ninety Five Only

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade

after throughly brushing the surfaces clean of all grease, dirt loose pieces of scales and also including two coats of Birla or Asian acrylic lappy (

One Hundred Twenty Three Rupees

39 10046.20 putty) and two coats of primer of approved brand and manufacture on new wall surface to give an even shade including thoroughly brushing 123.44 SMT ₹

And Paise Forty Four Only

the surface free from mortar dropping and other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly One Hundred Twenty Rupees And

brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete Paise Twenty Six Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing 20 mm thick water proof cement plaster using water proofing powder 1Kg/1bag of cement for all floors on brick / concrete wall work

using water proofing materials in C M 1: 4 ( 1 cement 4 coasrse sand) including finishing with a flooting coat of neat cement slurry etc complete

for all floor. and shall be guaranteed for minimum period of 10 years after handing over the completed building by the main contractor to be Three Hundred Forty Eight Rupees And

finished as directed. Stamp paper guarantee 10 years to be furnished before receiving any payment from the client. Paise Forty Five Only

Providing and laying 18 mm thick polished micro texture granite stone machine cut in single piece (Max. available) in sill and jambs of Door,

window, Ventilation frame laid over 10 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry with Three Thousand Two Hundred Sixty

42 660.82 matching pigment incl. rubbing and polishing half rounding edge etc. complete colour and shed as approved by architect engineer in charge. 3262.30 SMT ₹

Two Rupees And Paise Thirty Only

P & L 60x120 cm. Matt vitrified Tiles flooring 8 & 10mm Thick Tiles flooring over 20 mm (average) base of cement mortar 1:6 ( 1 cement:

coarse sand) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed 3 MM

One Thousand Five Hundred Sixty Five

43 1945.79 EPOXY GROOVE with color cement slurry including finised with flush pointing & cleaning the surface etc. complete and Colour Shade approved 1565.50 SMT ₹

Rupees And Paise Fifty Only

by Engineer-In-Charge

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M.

One Thousand Nineteen Rupees And

44 1548.36 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including 1019.39 SMT ₹

Paise Thirty Nine Only

rubbing and polishing etc. complete. (A) 20-25mm thick

Providing and laying Ceramic flooring tiles 300mm x 300mm in flooring treads of steps and landings laid on a Bed of 12 mm. Thick cement Nine Hundred Ninety Seven Rupees

mortar 1:3 (1 cement : 3 coarse sand) pointing in white ceand jointed with white cement slurry. And Paise Sixteen Only

Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo One Thousand Four Hundred Eighty

46 1162.75 on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry. 1488.24 Eight Rupees And Paise Twenty Three SMT ₹

Providing and laying Tactile flooring tiles 300mm x 300mm in flooring 12 mm. Thick cement mortar 1:3 (1 cement : 3 coarse sand) pointing in

One Thousand One Hundred Fourteen

47 211.85 white ceand jointed with white cement slurry. 1114.03 SMT ₹

Rupees And Paise Three Only

Providing and laying polished micro texture Granite slab flooring over 20 mm (average) base of cement mortar 1:6 (1 cement : 6 coarse sand)

One Thousand Nine Hundred Eight

48 249.96 laid and jointed with grey cement slurry including rubbing and polishing complete.18 mm thick 1908.90 SMT ₹

Rupees And Paise Ninety Only

Providing and fixing Colour Anodized aluminium work for doors, windows, ventilators and partitions (Sliding window like Two Track, Three

Track, Four Track, fix window/ Openable window / Fix-Partition, etc),with extruded built up standard tubular sections/ appropriate Z sections

and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with

expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc.

Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium Five Hundred Eighty Two Rupees And

49 1990.00 snap beading for glazing / paneling, C.P. brass / stainless steel screws, fixture like aldrop, handle, hinges / pivots & window Bearings & 582.38 Kg. ₹

Paise Thirty Eight Only

concealed lock etc all complete at all floors/all levels/all heights as per architectural drawings and the directions of Engineer-in-charge. (Glazing

and paneling to be paid under relevant Item)

Providing and fixing 4 mm thick ground glass (Frosted or obscured on one side) & (PIU approved brand list) fix in aluminium door, window,

ventilator shutters and partitions any size, any shape etc. P & F with EPDM/ PVC rubber gasket etc all complete at all floors/all levels/all heights

Seven Hundred Sixty Seven Rupees

50 44.00 as per the architectural drawings and the directions of Engineer-in-Charge. Actual laying installed glass shall be measured (Cost of aluminium 767.39 Sq.M ₹

And Paise Thirty Nine Only

snap beading shall be paid in basic item)

Providing and fixing 4 mm thick Sheet glass selected quality (PIU approved brand list) fix in aluminium door, window, ventilator shutters and

partitions any size, any shape etc. P & F with EPDM/ PVC rubber gasket etc all complete at all floors/all levels/all heights as per the

Seven Hundred Fifteen Rupees And

51 170.00 architectural drawings and the directions of Engineer-in-Charge. Actual laying installed glass shall be measured (Cost of aluminium snap 715.71 Sq.M ₹

Paise Seventy One Only

beading shall be paid in basic item)

Providing and fixing Stainless steel mosqito net jali ,S.S.315 Grade with wire of 0.56 mm (PIU approved brand list) fix in aluminium door,

window, ventilator shutters of any size, any shape with etc all complete at all floors/all levels/all heights as per the architectural drawings and

One Thousand Fifty Five Rupees And

52 56.00 the directions of Engineer-in-Charge. Actual laying installed Jali shall be measured. (Cost of aluminium snap beading shall be paid in basic item) 1055.23 Sq.M ₹

Paise Twenty Three Only

Providing and fixing 4 mm thick both side laminated compact sheet selected quality (PIU approved brand list) fix in aluminium door, window,

ventilator shutters and partitions any size, any shape etc. P & F with EPDM/ PVC rubber gasket etc all complete at all floors/all levels/all heights

as per the architectural drawings and the directions of Engineer-in-Charge. Actual laying installed sheet shall be measured (Cost of aluminium One Thousand Three Hundred Eight

snap beading shall be paid in basic item) Rupees And Paise Nine Only

Providing and fixing M.S. grill of required pattern of windows etc. with M.S.. flats at required spacing and frame alround square or round

headed bolts and nuts or by screws.including applying a priming coat of red lead paint and two coats of oil painting etc complete (A)Plain grill One Hundred Six Rupees And Paise

Twenty Three Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and laying Marbo Grenite double charge Vitrified tiles 8 to 10 mm thick , 24'' x 24'' full body double charge in flooring treads of steps

and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in white cement. One Thousand One Hundred Twenty

Rupees And Paise Thirty Six Only

Providing & laying 15 mm thick Kesariyaaji green Marble stone in single piece round edge surrounding door & window soffit & Jamb cladding &

window sill two up/down in single piece and pillars edge laid on 10 mm thick Cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with One Thousand Nine Hundred Eight

56 7.00 white cement with fix in soffit screw, rubbing & polishing etc complete as per instruction of Engineer-in-charge. 1908.02 SMT ₹

Rupees And Paise Two Only

Providing, fixing and construction of sand witch type platform of 18 mm thick Granite polished stone top, 100 mm wide edge full moulded

Facia Patti with 25mm thick prepolished Kota stone of uniform size and colour for bottom & supports at 90cm interval including necessary

cement mortar 1:2 Kota shall be fixed in cement joints and pointing as specified in Kitchen / Pantry / Counter / Laboratory etc with Eight Thousand Six Hundred Ninety

57 2.00 necessary adhesive, making of edges, polishing curing daily mopping with water and kerosene etc comp as directed of Engineer-in-charge. 8693.12 SMT ₹

Three Rupees And Paise Twelve Only

(Measured only vision finished top plan area)

Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1 including neat cement finishing, watering etc. complete. Twenty Four Rupees And Paise Twenty

Painting Two coats over & including a priming coat on new steel and other metal surfaces with enamel paint, brushing interior to give an even

shade including cleaning the surface of all dirt, dust and other foreign matter.. One Hundred Five Rupees And Paise

Forty Nine Only

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint.

(A)In beams and joists, channels angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, Nine Thousand One Hundred Eight

60 6.19 purlins conneted to common rafters and the like. 9108.48 Qntl ₹

Rupees And Paise Forty Eight Only

Providing and fixing 55 mm thick Single/Double shutter Specially Design door with 35mm flush door, solid core with two side 9 MM. Marine Ply

with Country wood Beading door shutter & 1mm Laminate on both sides colour, pattern and design of which is to be approved by the architect.

Durable Grip shall be providing with 30cm stainless steel handle and necessary Locking system of Godrej or Quivalent, stainless steel Four Thousand Five Hundred Eighty

61 166.00 hinges,Aldrops,Tower Bolts ,fixtures & fastenings, etc complete for all required materials labours and equipments as per detail drawing main 4580.35 SMT ₹

Rupees And Paise Thirty Five Only

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of

virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic

additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face)

& 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A

Three Thousand Nine Hundred Fifty

62 62.00 category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of 3958.59 SMT ₹

Eight Rupees And Paise Fifty Nine Only

required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In Charge. 35 MM

Providing and fixing bright finish brass hydraulic door closer of approved model and make with necessary screws and finishing etc. complete.

One Thousand Four Hundred Twenty

Three Rupees And Paise Nine Only

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off junctions Seven Hundred Seventy Nine Rupees

64 1572.53 and extending them upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed. 779.70 SMT ₹

And Paise Seventy Only

Fabricating, supplying and fixing in position SS railing for staircase and balcony with brush finish and 304 grade as per Indian Standrd and

detailed drawing including grinding, cleaning and filling the welded spots with SS finish (Only Length will be paid for payment heigth max.1.0 Two Thousand Fifty Seven Rupees And

65 279.00 mt.). The Work to be executed as per consultant drawing . 2057.37 RMT ₹

Paise Thirty Seven Only

Fabricating, supplying and fixing in position SS daso for staircase and balcony with brush finish and 304 grade as per Indian Standrd and

One Thousand Three Hundred Thirteen

66 112.00 detailed drawing including grinding, cleaning and filling the welded spots with SS finish (Only Length will be paid for payment ). The Work to be 1313.00 RMT ₹

executed as per consultant drawing .

Providing and fixing Sand which type Granite platform including supplying and fixing granite stone 18 mm thick mirror polished 1st quality

Granite stones in top and side posiition and vertical strip at front over 25 mm thick polished kotah stone platform fixing in top and sides and

itermediates supports fixing with cement mortar and adhesivee and finishing including cutting for fixing of sink any size (as directed by Two Thousand Seven Hundred Seventy

engineer incharge) at required position etc complete. Two Rupees And Paise Forty Five Only

Providing and fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size

with top & bottom rails of T iron 40 x 40 x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers Six Thousand One Hundred Sixteen

68 8.00 handles including applying a priming coat with red lead paint & Two Coat of oil paint etc. complete 6116.59 SMT ₹

Rupees And Paise Fifty Nine Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and fixing Flexible Homogeneous Vinyl Flooring of With treatment of Plyurethane Reinforced Surface, Densely Compacted, Anti- One Thousand Eight Hundred Ninety

69 158.00 Bactaril and fungicidal and Antistatic havng thickness of 2.00mm With weight of 3150 g/m2 with levelling, chemical adhasive for fixing, corner 1893.75 Three Rupees And Paise Seventy Five SMT. ₹

Wall Painting (two coats) with antibacterial polyrethane epoxy paint approved brand and manufacture on internal walls to give an even and

smooth surface. Thoroughly brushing the surface free from mortar dropings and other forein matter and sand prepared smooth. Four Hundred Fifty Four Rupees And

Paise Fifty Only

Providing & applying two Componant ,non slumping ,non-sagging, thixotropic epoxy bedding compond & adhesive compatible with for tiles for

coving at radius of 25 mm or as directed by the architect's / Engineer-in-charge make it fit for tiles inclusive of Labour, material and

Equipment etc. for all heights, location, shape & size as directed by the architect/Bank engineer incharge. (Actual Length shall be measured for Five Hundred Seventy Five Rupees And

payment.) Paise Seventy Only

Providing and applying 2mm thick Texture Plaster Terre Palette (Earthen Textures, Spectrum, Coral or equivalent) incorporating fine filaments

made of polymer and aggregating natural stone powder with making grooves on existing base coat of 18 mm thick smooth mala plaster etc. Three Hundred Fifty One Rupees And

72 645.00 Complete Colour and shade as approved by Architect/ Engineer in charge for all floor all height. 351.48 SMT ₹

Paise Forty Eight Only

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade

Ninety Two Rupees And Paise Twenty

73 272.00 including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter. 92.20 SMT. ₹

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular edge & 15 mm Thick Densified edges on the Tile

Periphery for Extra Strength The Light weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S. 476 part

IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best thermal Insulation . The Light weight calcium

Silicate tile shall be of approved texture Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or

equivalent of size 595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped galvanized steel sections

(galvanizing @120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and size of

24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to centre to form agrid of 1200X600mm and secondary

cross ’T’ of length 600mm and size 24x28mm made of 0.30 mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel

to form grid of size 600X600mm resting on periphery walls/partitions on a perimeter wall angle pre-coated steel of size (24X24X3000mm made

of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval

and laying 15mm thick Densified edges light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the grid

including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required, Main ‘T’

One Thousand Six Hundred Seventy

74 195.00 runners to be suspended from ceiling using G.I. slotted cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash 1674.15 SMT ₹

Four Rupees And Paise Fifteen Only

fasteners, 4mm G.I. adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to centre long main ‘T’

bottom exposed with 24mm of all T-sections shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawings and

as directed by engineer-in-charge.Note:- Only calcium silicate falseceiling area will be measured from wall to wall. No deduction shall be made

for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. Value of 0.50 (Minimum)

for Fine fissured/Spintone/Cosmos and 0.75 NRC for Globe, light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity. 0.043° w/m KC.for the best thermal Insulation

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per approved design Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and One Thousand One Hundred Fifty

75 725.00 filling the joint with sand in proper line and level as per guidlines of IRC : SP 63-2018 etc. Complete. 1157.16 SMT ₹

Seven Rupees And Paise Sixteen Only

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm length,30cm height and 15cm thick of M200 grade

Six Hundred Nine Rupees And Paise

76 600.00 concret as per approved design and including excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1 cement : 3 fine sand) 609.82 RMT ₹

Eighty Two Only

Providing corrugated G.I. sheet of class-3 roofing fixed with glavanished iron J or L Hooks, Bolts and nuts 8mm diameter with bitumen and G.I.

limpet washer or G.I. limpet washer. filled with white lead complete excluding the cost of purlins, Rafters and Trusses.(1) 0.80 mm thick sheet. Seven Hundred Thirty Four Rupees And

Paise Nineteen Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing, supplying, fabricating and erecting in position the structural steel for colums, grill, bars, truss, purlins, runners, cleats, insert plate,

base plate etc for all structural elements as per detail, made up from closed structural steel hollow sections (RHS/SHS including rolled section )

as per IS 4923 of grade Yst 310 mpa - weather resistant of Tata Structural / sections or an approved equivalent as per details /

drawings/instructions including cutting, bending, jointing, connecting, welding and / bolting and / riveting and fabricating and erecting in

One Hundred Sixteen Rupees And

78 2700.00 position etc complete for all levels as directed. The rate to include all necessary fixtures, fastening including welding rods of standard 116.15 Kg. ₹

Paise Fifteen Only

approvded quality etc for complete the job. The rate shall also include the one coat of red lead paint, epoxy coat & necessary scaffolding etc.

complete as directed

Drilling Of 215mm Dia Bore In Over Burden Strata & Lowering Of Casing & Further Drilling Of 165mm Dia. Bore In Soft & Hard Rock With

Devlopment Of Bore Measuring The Yeild & Fixing Of Bore Cap Etc. Completed (I)0.0Mts To 150.00Mts Two Hundred Sixty Six Rupees And

Paise Sixty Four Only

Providing and Supplying Of 175mm Normal Dia.UPVC Casing Pipe. Five Hundred Thirty One Rupees And

Paise Forty Seven Only

Providing & Fitting Of 200mm Dia. Cap Plug. Seven Hundred Fifty Two Rupees And

Paise Twenty Seven Only

Providing & Fixing HDPE Pipe For Bore Well.(I) 32MM Dia Fifty Five Rupees And Paise Fifty Five

FLUSH PARTITION (laminate finish) :Providing & fixing flush partition up to false ceiling ht (thickness of partition is 75 mm) having 12 mm

thick Marin plywood IS 710 both side on aluminum framing. Aluminum framing size for vertical & horizontal support is 50 mm x 25 mm. All

exposed surfaces finished with 1 mm thick laminate of approved shade without any air gap and grooving as per design. Necessary framing to

be erected above false ceiling. No extra cost to be paid for the same. Before installation, make hole/face plate for conduit pipes of electrical /

networking cables with open able stud from partition Including all materials and labor etc. Make necessary grooves as per shown in drawing.

All bottom ends are covered with Ghana teak bidding Patti finished with laminate Complete with all necessary hardware & adhesives as per Four Thousand Five Hundred Twelve

details given in drawing and as per instructions of Architect/ consultant /Engineer In charge. Contractor has to provide all necessary cut outs Rupees And Paise Thirty One Only

(race ways.) for Electrical works & no extra payment shall be made for it.

Partly glazed partition: Providing & fixing full height partly laminated & partly glazed partition (up to false ceiling ht) using 12 mm thick

marin plywood IS 710 both side on aluminum framing of guage 16 . Aluminum framing size for vertical & horizontal support is 50 mm x

mm .Grid of aluminum framing is 600 mm x 600 mm. All exposed surfaces finished with 1 mm thick laminate of approved shade without any

air gap and grooving as per design. . Necessary framing to be erected above false ceiling (up to beam and slab height.) No extra cost to be paid

for the same. Before installation, make hole/face plate for conduit pipes of electrical / networking cables with open able stud from partition

Including all materials and labour etc. For glazing Using of 12 mm thick toughen clear glass with proper crystal edges & with suggested frosted Four Thousand Nine Hundred Fifty Six

films on glass. Frosted film material rate is provided extra as per given cost in tender item. All joints are covered with Ghana teak bidding Patti Rupees And Paise Six Only

finished with laminate. Complete with all necessary hardware & adhesives as per details given in drawing and as per instruction of

Architect/consultant/Engineer In charge.

STORAGE BELOW PANTRY COUNTER :Providing & fixing full ht storage having size as per detail drawing , having depth of 600 mm, having

skirting of 75 mm, with proper locks. 5 nos of vertical supports & 3 no of horizontal shelves made by 19 mm thick Marin ply, having shutters of

9 mm thick double sandwich ply with using 12 mm thick Marin ply for framing. All complete with proper Burma teak biding. Back ply is 12 mm

Marin ply. All exposed & internal surfaces are covered with 1 mm thick laminate. External & internal joints covered with bidding Patti complete Four Thousand Two Hundred Ninety

85 4.50 with laminate finish. All complete with proper hardware like locks, S.S. Screws, MS Nails, Magnets, table chains, cable manager SS 304 Handles 4293.39 Three Rupees And Paise Thirty Nine SMT ₹

of 250 mm and 100 mm dia etc. All Details as per shown in detail drawings & as per instructions of architect/consultant / in charge engineer Only

Providing And filling with good quality sinder(steam coal) as directed by engineer in charge in sunks in layers of 15 cm thick,including

Four Hundred Fifty Two Rupees And

86 36.00 watering,placing ,ramming well etc as directed, for all floor. 452.48 CMT ₹

Paise Forty Eight Only

Providing and fixing 18mm-20mm thick water proof plywood shutters for kitchen cabinet including using approved formica on shutter and

teakwood decorative batten patti in froun portion with necessray fixtures and fastenings including polishing work etc. complete and direction Four Thousand Two Hundred Fifty Six

of engineer in charge. Rupees And Paise Twenty Eight Only

Corner Guard Protection System in entire hospital : Supply and Installation of Corner Guard protection system fixed to brick wall/or tile/dado at

the corner from finished floor level. It should be adjustable end cap. Providing and fixing brush/mirror finish S.S 304 grade Angle 40.0 x 40.0 x Seven Hundred Eighty Eight Rupees

3.0 mm &. 1.00mt. Ht. x 3.75 kg/mt. = 3.75 kg. And Paise Eighty One Only

LOUVERS: Supplying and Installation of GI 84C powder coated louvers etc complete as per drawing& selection as directed by Architect/Engineer Two Thousand Four Hundred Sixty

89 136.00 incharge. 2460.36 SMT ₹

Rupees And Paise Thirty Six Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing & fixing –Roller blind curtain with head rail as standerd make – with necessary fitting with fabric shadeas. The fabric is 100% polyester

with epi- -176 the weight of fabric – 390 gsm-as warp-80 den twisted & weft -300 den roto as max width of fabric-230 cm.as per instruction of One Thousand Eight Hundred Two

Architect & E.I.C. Rupees And Paise Eighty Five Only

Writing letter or figures on any surface with black japan paint (stops,comas, hyphens and the like not to be measured and paid for separately)(i)

Block (Letters/Figures) (Per 10 Letter pet CM.HT) Three Rupees And Paise Thirty Four Per Letter

Only Per Cm/Ht.

Writing letter or figures on any surface with black japan paint (stops,comas, hyphens and the like not to be measured and paid for separately)

(ii) Indian (Letters/Figures) Per Letter

92 15.00 3.52 Three Rupees And Paise Fifty Two Only ₹

Extra over above items for using thick white paint instead of black japan paint. (i) Block (Letters/Figures)

93 10.00 0.07 Zero Rupees And Paise Seven Only ₹

Providing and fixing 3 mm thick PVC sheets as signange and display of health signs/information of required size having retro reflective

letters/design as per requiement, fixing the same through approved adhesive etc. complete work shall e carried out as per instruction of Three Hundred Eighty Two Rupees And

Engineer-in-charge (Approved make PVC foamed sheet only) (45 x 15 cms.) Paise Seventy Nine Only

Providing and fixing Un-insulated fire rated GI Sheet doors conforming to FD 120 classification of IS 3614 :2021 with fire rating of 120 minutes

integrity. The factory manufactured door frame and shutter assembly shall be made out of minimum 1.20 mm thick GI Sheet with minimum

120 GSM coating as per IS: 277. Door and frame should be finished with powder coating in standard RAL shade finish having DFT of minimum

30 microns. The door should carry a minimum 500 Hrs of salt spray test. All accressesories like hardware, vision panel, fire & smoke seal etc to

be supplied by Fire door manufacturer only as per the guidelines laid down in IS 3614:2021.Every door must carry a label confirming to type of

door & its fire rating. The door must carry a 5years valid test evidence from CBRI-Roorkee / NTH-Kolkata/ NABL accrediated lab which operates

in accordance with ISO/IEC 17025.The Door frame shall be single rebate grooved profile of size minimum 100mm x 57mm made out of 1.20mm

(18gauge) minimum thick galvanized steel sheet. Frames shall be butt / mitered joint and field assembeled with bolting system. Frames to have

inbuilt grooved to accomodate Intumuscent fire seal strip 10X4MM, It shall be fixed in grooves, specifically cut in rebate on all the 3 sides of the

frame . The frame should also be provided with fire rated EPDM smoke seal 12X12 mm conforming to IS: 3614:2021 or as per test evidence...

All provisions should be mortised & provided with necessary inbuilt reinforcement to receieve appropriate hardware.Frames should be

provided with back plate bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide

sleeves(Payable in extra item) for installation of frame in finished plastered masonary wall opening. Note :- For grouting of Steel frames in

masonary installations ;cement sand mixture 1:3 ratio by civil contractor/fire rated PU foam or such fire rated material may be recommended

except head member.Door leaf should be minimum 46mm thick fully flush double skin door. Door leaf must be manufactured from

1.2mm(18gauge) thick galvanised steel sheet. The infill material shall be resin bonded paper honey comb infill. All doors shall be factory Twenty Two Thousand Seven Hundred

prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should Twenty Five Rupees Only

be interlocked with a bending radius of 1.4mm. For double leaf doors integrated astragals has to be provided on the meeting stile for both

active and inactive leaf.The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges of size 100x 75x3 mm alongwith

all suitable hardware.Vision lite size 300x400 mm or 150 x 800mm(max area 0.12sqm) wherever applicable should be provided with single

layered clear fire rated glass panes as per guidelines laid down under IS 3614 2021 vide clause no. 7.2.7 table no. 2 with a clipon arrangement.

The glass will be provided with fire rated ceramic tape of min.2 mm thickness with min.15mm width alround on either face. Every Glass pane

must carry a permanent marking of its glass manufacturer Note:-As per drawings and design supplied by architect and instruction given by

authority and E.I.C.

Providing and fixing in position cowel went to pipes.(B) 75mm dia. Three Hundred Ninety Three Rupees

And Paise Four Only

Providing and fixing in position cowel went to pipes.(C) 100mm dia Five Hundred Five Rupees And Paise

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia. One Hundred Eighty Six Rupees And

Paise Eighty Three Only

Providing and fixing Gun metal check or non-return One Hundred Eighty Six Rupees And

fullway wheel valve.(A) 15mm dia. Paise Eighty Three Only

Providing and fixing Gun metal check or non-return Two Hundred Three Rupees And Paise

fullway wheel valve.(B) 20mm dia. Eighty Two Only

Providing and fixing Gun metal check or non-return Four Hundred Twenty Rupees And

fullway wheel valve.(C) 25mm dia. Paise Sixty Three Only

Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia. Three Hundred Fourteen Rupees And

Paise Seventy Three Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and fixing ball cock of approved. quality as One Hundred Thirty Seven Rupees And

directed.(B) Abonite (ii) 50mm dia. Paise Eighty Nine Only

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length. One Hundred One Rupees And Paise

Ninety One Only

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for

potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 One Hundred Seventy Rupees And

mm. Paise Thirty Six Only

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary Seventy Two Rupees And Paise Sixty

106 385.00 fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. 72.65 Rmt ₹

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary Ninety One Rupees And Paise Eighty

107 350.00 fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. 91.84 Rmt ₹

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary One Hundred Nineteen Rupees And

108 76.00 fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. 119.15 Rmt ₹

Paise Fifteen Only

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary One Hundred Forty Eight Rupees And

109 150.00 fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. 148.12 Rmt ₹

Paise Twelve Only

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary One Hundred Ninety Five Rupees And

110 165.00 fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. 195.67 Rmt ₹

Paise Sixty Seven Only

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm

heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. Eight Hundred Thirty Four Rupees And

including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Paise Thirty Eight Only

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm

heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. Eight Hundred Fifty Seven Rupees And

including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Paise Sixty Five Only

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polythene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(F) 75mm Two Hundred Eighty Rupees And Paise

Twenty Three Only

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm Three Hundred Thirty Nine Rupees And

Paise Five Only

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)160 mm Six Hundred Ninety Six Rupees And

Paise Ninety Only

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 75 mm diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of cutting and making good the walls. Five Hundred Seventy Four Rupees And

Paise Fifty Eight Only

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to

Eight Hundred Fifty Nine Rupees And

117 1.00 wooden pluge with C.P. brass screws and washers. 859.41 Each ₹

Paise Forty One Only

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Six Hundred Sixteen Rupees And Paise

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and fixing 25mm size UPVC Ball Valve with necessary Adhesive and fittings as directed by Engineer in charge. Five Hundred Forty Nine Rupees And

Paise Sixty Eight Only

Providing and fixing 40mm size UPVC Ball Valve with necessary Adhesive and fittings as directed by Engineer in charge. One Thousand Three Hundred Forty

120 4.00 1345.71 Five Rupees And Paise Seventy One Each ₹

Providing and fixing brass cromium plated surgical handle cock of size of 15mm dia as per PIU Approved brand list etc. complete as directed by One Thousand Eighty Eight Rupees And

121 1.00 engineer incharge. 1088.21 Each ₹

Paise Twenty One Only

Providing erecting and fixing three coated white Antibecterial Syntex PVC. (ISI) water tank of required capacity each with all Eleven Rupees And Paise Eighty One

122 500.00 necessary fittings and connection etc. complete on terrace. 11.81 litre ₹

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing

Five Hundred Eighty Five Rupees And

123 74.00 design with C.I scread down or hinged grating including the cost of cutting and making good the walls. 585.37 each ₹

Paise Thirty Seven Only

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary fittings and connection etc. complete on Three Rupees And Paise Ninety Five

124 40000.00 terrace 3.95 litre ₹

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P & S type. One Thousand Two Hundred Ninety

Two Rupees And Paise Nineteen Only

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for collar joints including testing of joints complete.(B) 150mm Two Hundred Fifty Four Rupees And

Paise Eighty Nine Only

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation

concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1- Cement :

3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 Cement :2-Coarse sand :4-

stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep Eleven Thousand Forty Two Rupees

including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. And Paise Seventy Four Only

of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar

1:5 (1- Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.

(I) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No.24.27 (I) for depth from 0.9M to Five Hundred Twenty Two Rupees And

1.5M. Paise Ninety Six Only

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation

concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1- Cement :

3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 Cement :2-Coarse sand :4-

Nineteen Thousand Three Hundred

stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep

129 2.00 19349.63 Forty Nine Rupees And Paise Sixty Each ₹

including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt.

of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar

1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm diameter sewer.

(II) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. GR Part thereof over item No.24.27 (I) for depth from 1.50M. to Three Hundred Ninety Seven Rupees

2.25M. And Paise Nineteen Only

Providing and fixing cast iron steps of size 500mm x150mm x 22.5mm and painting with two coats of Anti corrosive paint etc. complete. Two Hundred Seven Rupees And Paise

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less

than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1 cement :2- coarse sand :4-graded stone aggregate Two Thousand Nine Hundred Thirty

132 13.00 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement 2932.93 Two Rupees And Paise Ninety Three Each ₹

on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line. Only

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick Two Hundred Forty Two Rupees And

masonry chamber.(i) for 455mm x 610mm size. Paise Thirty Nine Only

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less

than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement Three Thousand Six Hundred Sixty

on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. Rupees And Paise Seventy Six Only

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x Two Hundred Sixty Four Rupees And

700mm size. Paise Eighty Six Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than

35Kg/ Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less

than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1 cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement Seven Thousand One Hundred Eighty

on walls and bed concrete etc. complete.(iii) Inside dimensions 600mm x 850 mm and 450mm deep for pipe lines with three or more inlets. Rupees And Paise Forty Four Only

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(iii) for 600mm x Three Hundred Twenty Five Rupees

850mm size. And Paise Fifty Nine Only

Providing junction for rain water juncton chamber of size 0.60x0.60x0.75m with excavation of size 1.96x1.96 m & 0.15m thick c.c.1:2:4 bed

concrete including brick masonary wall in CM 1:6 of 0.75m height & 0.23m thick with 15mm thick cement plaster inside & outside & 1.06x1.06 Ten Thousand Thirty Five Rupees And

RCC (1:2:4) slab of thickness 0.15m with CRS steel and 0.60mx0.45m cast iron manhole cover with frame weight not less than 35 kg as per Paise Thirty Six Only

directed by Engineer-in-charge (RA-2)

Providing Filter chamber of Brick work in C:M 1:6 of size 2.06mx1.20m x1.20m & excavation dimension of 2.66mx 1.81x1.35m including C.C

1:2:4 bed concrete of 0.15m thick including brick work in c.m 1:6 for 23cm thick wall including 15mm thick cement plaster inside & outside with Seventeen Thousand Nine Hundred

139 2.00 cement slurry & 10cm thick RCC 1:2:4 top cover with frame of minimum weight of 35 kg & filling filter material kapchi in layers (25-40mm & 10- 17907.35 Seven Rupees And Paise Thirty Five Nos. ₹

20mm) & BT metal 40mm & sand as per directed by Engineer-in-charge. Only

Providing Recharging pit of size 2.0m Dia.& 2.0m depth of water logging with excavation filling the pit with gravel & sand in layers including

Thirteen Thousand Seven Hundred

140 2.00 making 300mm dia bore depth of 4.5mt & above concrete with kapchi in layers (25-40mm & 10-20mm) & BT metal 40mm & filling brick as 13708.09 Nos. ₹

Eight Rupees And Paise Nine Only

directed by Engineer-in-charge.

Providing and fixing ( 600 mm X 450 mm X 150 mm) size vitreous china laboratory sink brand of approved quality with CI or MS brackets

painted white including cutting holes and making good the same including providing and fixing 32 mm dia CP waste coupling rails providing Two Thousand Four Hundred Eighty

141 12.00 fixing PVC waste pipe etc. comp as approved by the Engineer in charge. The white glazed earthenware laboratory sink (HINDWARE, SONA, 2487.49 Seven Rupees And Paise Forty Nine Each ₹

CERA brand of approved quality) shall be 600 x 450 x 150 mm of best quality and make as approved by the Engineer-in-charge. Only

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including

Three Thousand Four Hundred Forty

142 1.00 covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. 3445.18 Each ₹

Five Rupees And Paise Eighteen Only

Providing and fixing Two way BIB cock with wall flange of genuine Jaquar ompany brand, in with model no FUS-CHR29041, water tap brand or

approved ISI brand quality, fixing in pieline and testing the same… etc., complete., as directed by EIC Three Thousand One Hundred Thirty

One Rupees Only

Providing and fixing white vitreous china extended wall mounted water closet (European type) of size CALIBRE 660 x 360 x 760 mm with Top

Toilet Seat cover with Cistern & Jet Spray as per PIU Approved brand list including providing and fixing vitreous china 100 mm size 'P' or 'S' trap Ten Thousand Five Hundred Thirty Five

including all jointing the trap with pan and soil pipe in CM (1:1) (1 cement :1 fine sand) etc complete as directed by Engineer in charge. Rupees And Paise Twenty Seven Only

Providing and fixing flat back wash basin 550 mm x 400 mm size of first grade, white in colour with single hole for pillar trap with CI or MS

brackets painted with including cutting holes and making good the same including providing and fixing CP brass waste coupling 32mm dia &

waste pipe , including providing and fixing 15mm dia pillar tap capstan head screw down high pressure with screws, shanks and back Two Thousand One Hundred Nine

nuts,including providing and fixing waste pipe 15mm x 600 mm pvc inlet connection 15mm brass screw down stop tap with necessary fittings Rupees And Paise Eleven Only

Providing and fixing urinal of approved connecting the urinal with waste pipe ,trap,and 15 mm dia stop tap etc. complete (A) White One Thousand Two Hundred Eighty

earthenware flat back or corner type size 430 x 260 x350 mm. Rupees And Paise Sixty Nine Only

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each Two Hundred Eighty Two Rupees And

Paise Sixteen Only

Providing and fixing U PVC SCH40 for cold water 20 mm dia (3/4)" Eighty Nine Rupees And Paise Eighty

Providing and fixing PVC SWR pipes IS 13592 for Drain - 75 mmdia Three Hundred Eighty Six Rupees And

Paise Eighty Three Only

Providing and fixing PVC SWR P & S- Trap IS 14735 for Drain -110x110 Three Hundred Fifty Seven Rupees And

Paise Fifty Four Only

Providing and fixing Gun metal check or non-return fullway wheel valve. (A) 50mm dia. Eight Hundred Seventy One Rupees

And Paise Sixty Three Only

Providing laying and jointing PVC SWR pipes IS 13592 for Drain - 50 mmdia it's accessories. Three Hundred Thirty Seven Rupees

And Paise Thirty Four Only

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. Five Hundred Twenty Rupees And

Paise Fifteen Only

Providing and fixing SS finish Angular Stop cock for wash basin like Jaquar code FUS-29053 One Thousand Seven Hundred Forty

154 45.00 1742.25 Two Rupees And Paise Twenty Five No. ₹

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and fixing Handicap wash down water closet European type WC pan (Wall Hung) like JAQUAR CNS-WHT-961SPP- SIZE

365x545x360MM and P trap distance 23.5 cms with integral P trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement :

find sand) including providing and fixing of 1) Health Faucet hand shower heavy duty with SS braided hose 1.2 MT long pipe to water closet -

JAQUAR ALD-CHR-573 with Single Piece Slim Concealed Cistern Body with Installations Kit & “S-Type” drain pipe connection set for Wall Hung Twenty Three Thousand Five Hundred

WC (without Flush Control Plate) - JCS-WHT-2400S with Control Plate Opal - JCP-CHR-152415,Toilet roll holder -Jaquar -ACN -1151N, including Thirty Three Rupees Only

grab bar etc,complete

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front

plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (f) with Five Hundred Eighty Two Rupees And

medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete cat III Paise Seventy Seven Only

Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires, in below type of pipe to be erected complete with earth continuity and

necessary connection with primary light with accessories erected on Metal / PVC / wooden box covered with 3 mm thick

PC(Polycarbonate) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as Two Hundred Rupees And Paise Ninety

directed. Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point. (f) with medium class Rigid PVC pipe Nine Only

and accessories erected concealed in wall/ceiling complete cat III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected with 6A Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single Eight Hundred Nine Rupees And Paise

mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe One Only

erected. with necessary ceiling rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete cat III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires erected in below type of pipe with 6A Modular type switches and following type of accessories erected

on PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate modules erected on / in wall / Seven Hundred Twenty Five Rupees

ceiling as per pipe erected. with necessary batten/angle holder or ceiling rose or H.D.Connector as directed. (f) with medium class Rigid PVC And Paise Eighteen Only

pipe and accessories erected concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of Eight Hundred Ninety Four Rupees And

accessories [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board. (f) with medium class Rigid PVC pipe and Paise Eighty Six Only

accessories erected concealed in wall/ceiling complete cat III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with

following type of accessories. [III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green) earthing wire from mcb d One Thousand Forty Six Rupees And

b board.(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Paise Thirty Six Only

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules erected on / in wall / ceiling with following type accessories Cat. III Three Hundred Nine Rupees And Paise

Providing & erecting Switch board for Computer or electric apparatus consisting of following modular type accessories mounted with

PVC / Metallic concealed/open box with single mounting base frame covered with textured/metallic /white front plate,modules One Thousand One Hundred Thirty

163 40.00 erected with necessary connections as directed 1 no. 6A/16A universal plug-switch combined. 3 nos. 6A Switch 3 nos. 6A 5 pin Plug For 1133.22 Three Rupees And Paise Twenty Two Ea ₹

Modular Type Accessories Cat. III Only

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base

One Hundred Sixty Rupees And Paise

164 40.00 frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation 160.59 Ea ₹

Fifty Nine Only

directed by Engineer In charge. (8) Computer RJ-45 socket Cat.III

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction [D] CAT - 6 e Seventy Six Rupees And Paise Seventy

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base

One Hundred Sixty Rupees And Paise

166 35.00 frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation 160.59 Ea ₹

Fifty Nine Only

directed by Engineer In charge. (3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation Twenty Five Rupees And Paise Twenty

167 240.00 directed by Engineer In charge. (7) Blank Plate Single Cat.III 25.25 Ea ₹

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped

with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in

168 1500.00 existing pipe. of following size of conductors & nos.of pairs. With necessary connections. [A] Conductor Size 0.5 mm (a) Unarmoured 20.20 Twenty Rupees And Paise Twenty Only Mtr. ₹

Providing & erecting main Distribution (MDF) indoor type, back mounted frame as per DoT standard approved with krone strips (c) Suitable One Thousand Seven Hundred Forty

Seven Rupees And Paise Thirty Only

SITC of Digital / PCM / TDM EPABX System having SMT design, system with flexible universal slots. Inbuilt Auto attendant facility, Minimum

Nos. conference, Analog extension line, Calling GSM, E&M line, PRI / EI & VOIP program me through Analog telephone digital key from

Ethernet, public address cord, shall have unrestricted simultaneous dialing facility, QSIG protocol on PRI, 95 / STD / ISD / Local-Locking, Class of

Service, Quick Dial-Single Digit dialing of any two external number, Once only ring device, Chairman / Secretary - Do not disturb Facility, Power

Down Mode, Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing Seventy Seven Thousand Seventy

with Voice Guide System, (DISA), Caller ID (CLI), CLI Base ECF, CLI Base routing Internet Ready Port, External Music Port, Call Budgeting, Call Seven Rupees And Paise Fourteen Only

Most Calculation (ASMDR), DID Direct Inverse Dialing, External Music Input, Fax Homing, Global Directory Printing with following capacities

[[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] [C] No of Extension 48, No of Junctions 9, 8 Port IP Resource

in-built, 4 Port Web base Video Conferencing, No of expandable ports : 128, Operators Console - 01 Compatible : ISDN

Supplying & erecting push button type telephone instrument having speaker phone Caller ID & hands free dialing system & 30 memories with

display system Single line [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Five Hundred Sixty Five Rupees And

Paise Sixty Only

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation One Hundred Sixty Rupees And Paise

directed by Engineer In charge. (4) TV Co-axial Socket outlet Cat.III Fifty Nine Only

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated

with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall Thirty Nine Rupees And Paise Thirty

173 300.00 sheathed with black PVC insulation. (b) RG-6 39.39 Mtr. ₹

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant

PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power One Hundred Fifteen Rupees And Paise

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (f) One wire 10.00 sq. mm Fourteen Only

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant

PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power One Hundred Seventy Seven Rupees

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (g) One wire 16.00 sq. mm And Paise Seventy Six Only

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant

PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power Two Hundred Ninety Five Rupees And

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (h) One wire 25.00 sq. mm Paise Ninety Three Only

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant

PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power Three Hundred Seventy Six Rupees And

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (i) One wire 35.00 sq. mm Paise Seventy Three Only

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green Seventy Eight Rupees And Paise

178 2200.00 colour for earth continuity of following size. (A) With medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq. mm 78.78 Mtr. ₹

Seventy Eight Only

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green One Hundred Four Rupees And Paise

179 12500.00 colour for earth continuity of following size. (A) With medium class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm 104.03 Mtr. ₹

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of One Hundred Forty Rupees And Paise

180 2200.00 following size (A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm 140.39 Mtr. ₹

Thirty Nine Only

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of One Hundred Eighty Four Rupees And

181 400.00 following size (A) with medium class Rigid PVC pipe and accessories (b) 2 wire 6 sq. mm 184.83 Mtr. ₹

Paise Eighty Three Only

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of Three Hundred Twenty Six Rupees And

following size (A) with medium class Rigid PVC pipe and accessories (h) 4 wire 6 sq. mm Paise Twenty Three Only

(i) 4 wire 10 sq. mm (use earth wire of 4 sq.mm ) Five Hundred Thirty Two Rupees And

Paise Twenty Seven Only

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected

with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as Twenty Four Rupees And Paise Twenty

directed Four Only

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected

Thirty Three Rupees And Paise Thirty

185 800.00 with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as 33.33 Mtr. ₹

directed (b) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected

Fifty Four Rupees And Paise Fifty Four

186 450.00 with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as 54.54 Mtr. ₹

directed (c) 32 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of Twenty One Rupees And Paise Twenty

following sizes.(2) 25 mm One Only

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid material with ignition free and flame proof

Four Hundred Twenty Eight Rupees

188 20.00 confirming BS with necessary end caps Internal and external bend, flat bends, coupler, tee etc..All necessary accessories and measuring of 428.24 Mtr. ₹

And Paise Twenty Four Only

following sizes(2) 100 mm x 50 mm trunking

189 100.00 Bakelite adopter for Holder to be erected. 9.09 Nine Rupees And Paise Nine Only Ea ₹

Supplying & erecting Approved make call bell indicator with buzzing sound and Red light indicating lamp with Red light button to attend the One Hundred Forty Eight Rupees And

call suitable for 240 v 50 Hz supply to be erected. Paise Forty Seven Only

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link,

earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs One Thousand One Hundred Fifty Two

should be used of same company of MCB to be used) Rupees And Paise Forty One Only

suitable for (A) single phase incoming and horizontal single phase outgoing (b) sheet steel double door (IP-43) (iii)8 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link,

earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Three Thousand Four Hundred Twelve

Per phase isolation type (PPI) (b) sheet steel double door (iii)8 way Rupees And Paise Seventy Nine Only

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link,

earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)suitable for(B) three phase incoming and single phase horizontal type outgoing Three Thousand Eight Hundred Seventy

Per phase isolation type (PPI) (b) sheet steel double door (iv)12 way Four Rupees And Paise Thirty Six Only

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III One Hundred Twenty Three Rupees

And Paise Twenty Two Only

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking capacity & confirms to IS : 8828 in Three Hundred Six Rupees And Paise

195 24.00 existing box having following capacity (A) 6 to 32 Amp. Cat-III 306.03 Ea. ₹

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking capacity & confirms to IS : 8828 in Three Hundred Twenty Five Rupees

196 8.00 existing box having following capacity (B) 40 Amp. Cat-III 325.22 Ea. ₹

And Paise Twenty Two Only

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in Six Hundred Fifty Five Rupees And

197 12.00 existing box having following capacity (a) 6 to 32 Amp. Cat.III 655.49 Ea. ₹

Paise Forty Nine Only

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in Seven Hundred Thirty Six Rupees And

198 10.00 existing box having following capacity (b)40 Amp. Cat.III 736.29 Ea. ₹

Paise Twenty Nine Only

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in

Eight Hundred Eleven Rupees And

199 20.00 existing box having following capacity (c) 63 Amp. Cat.III 811.03 Ea. ₹

Paise Three Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand

capacity of 10 KA and suitable for operation on single phase 240 V,50Hz. having characteristic of quick action & tripping with all Two Thousand Four Hundred Fifty

advance feature & do not incorporate any electronic component. for following Max. rating erected as directed (ii) 40Amps. DP Cat. III Eight Rupees And Paise Thirty Four Only

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket One Thousand Nine Hundred Sixty One

to each bar, erected in existing cubical panel with necessary connections. Rupees And Paise Forty Two Only

(A) Suitable for 100 Amp. Capacity

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket Three Thousand Two Hundred Two

to each bar, erected in existing cubical panel with necessary connections. Rupees And Paise Seventy One Only

(B) Suitable for 200 Amp. capacity

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket Four Thousand Nine Hundred Nine

203 6.00 to each bar, erected in existing cubical panel with necessary connections. 4909.61 Rn.Mtr ₹

Rupees And Paise Sixty One Only

(C) Suitable for 300 Amp. capacity

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket Seven Thousand Three Hundred

204 5.00 to each bar, erected in existing cubical panel with necessary connections. 7319.47 Nineteen Rupees And Paise Forty Seven Rn.Mtr ₹

(D) Suitable for 400 Amp. capacity Only

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket Ten Thousand Five Hundred Fifty Nine

205 5.00 to each bar, erected in existing cubical panel with necessary connections. 10559.55 Rn.Mtr ₹

Rupees And Paise Fifty Five Only

(E) Suitable for 630 Amp. capacity

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with

Six Thousand Seven Hundred Ninety

206 10.00 all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. 6790.23 Ea ₹

Rupees And Paise Twenty Three Only

housing. Cat III

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader Eight Thousand Eight Hundred Sixty

207 2.00 tinned copper & complete erected in existing 16 G.M.S. housing. Cat III 8861.74 One Rupees And Paise Seventy Four Ea ₹

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader Seventeen Thousand Eight Hundred

208 4.00 tinned copper & complete erected in existing 16 G.M.S.housing. Cat III 17843.67 Forty Three Rupees And Paise Sixty Ea ₹

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. and above at 415 V .

having normal current rating 250A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal Twenty Three Thousand Forty One

209 2.00 connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. Cat III 23041.13 Ea ₹

Rupees And Paise Thirteen Only

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 50 KA and above at 415 V

having Normal current rating 400A. with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. With all internal Twenty Seven Thousand Seven

210 6.00 connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. Cat III 27751.77 Hundred Fifty One Rupees And Paise Ea ₹

Seventy Seven Only

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 50 K.A. and above at 415 V

having normal current rating up to 630A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal Thirty Thousand Nine Hundred Ninety

211 3.00 connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing cat III 30991.85 Ea ₹

One Rupees And Paise Eighty Five Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Supplying & erecting approved make Four Pole 415V change over switch interior for panel mounting with operating mechanism A.C.23 duty Twenty Six Thousand One Hundred

212 2.00 confirming to IS for 26149.91 Forty Nine Rupees And Paise Ninety Ea ₹

(G) 630 A. Cat.III One Only

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board necessary

IP- 42 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors,

16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel including

cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of

engineer-in- charge with erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted Fourteen Thousand Nine Hundred Two

213 7.00 with epoxy powder coating (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, 14902.55 Sq.Mtr ₹

Rupees And Paise Fifty Five Only

meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following

approved manufacturers with following size. (B) The standard companies switch gear shall be used and only manufacturers at

CPRI approved factory. (i) with 350mm depth board

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board necessary

IP- 42 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors,

16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel including

cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of

engineer-in- charge with erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted Nineteen Thousand Three Hundred

214 3.00 with epoxy powder coating (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, 19387.96 Eighty Seven Rupees And Paise Ninety Sq.Mtr ₹

meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following Six Only

approved manufacturers with following size. (B) The standard companies switch gear shall be used and only manufacturers at

CPRI approved factory. (ii) with 550 mm. Depth

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board necessary

IP- 42 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors,

16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel including

cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of

engineer-in- charge with erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted Forty Thousand Nine Hundred Ninety

215 3.00 with epoxy powder coating (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, 40999.94 Nine Rupees And Paise Ninety Four Sq.Mtr ₹

meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following Only

approved manufacturers with following size. (B) The standard companies switch gear shall be used and only manufacturers at

CPRI approved factory. (iv) with 1000 mm. depth

Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections complete with cutting, welding, grinding & finishing duly painted with one

coat of red oxide with erection on site as per direction of engineer in charge with necessary grouting, cementing, plastering & Seventy Seven Rupees And Paise

216 1200.00 finishing 77.77 Kg. ₹

Seventy Seven Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and erecting multifunctional meter suitable for application of Power monitoring and showing measurement of following Voltage,

Frequency, Apparent energy, Apparent power, Active and reactive energy, Active and reactive power, Average voltage Vavg, Peak demand

power PM, QM, SM, Demand power P, Q, S, Apparent power S, S1, S2, S3, Unbalance current, Power factor and displacement PF (signed, four

quadrant), Calculated neutral current, Active, reactive, apparent energy (signed, four quadrant), Active power P, P1, P2, P3, Voltage U21, U32,

U13, V1, V2, V3, Phase currents, Average current Iag, Peak demand currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3, [Us] Fourteen Thousand One Hundred

217 8.00 rated supply voltage 40...300 V AC 45...65 Hz, 40...300 V DC, Network frequency 50 Hz, Type of network 3P, Display type 7 segments LED, 14123.84 Twenty Three Rupees And Paise Eighty Ea ₹

Display colour Red, Messages display capacity 3 fields of 4 characters, Display digits 12 digit(s) - 14.2 mm in height Four Only

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover, complete erected with necessary connections. Forty Three Rupees And Paise Forty

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA burden erected in existing CRCA box Two Hundred Seventy Four Rupees

219 3.00 duly secured with insulating materials connected to the meter. 274.72 Ea. ₹

And Paise Seventy Two Only

Providing and erecting Approved make Earth fault Relay suitable to mount with inter connection suitable to following size of moulded case

circuit breaker having CT ratio & MCCB rating as following along with shunt trip 220V AC. with all internal connections & complete erected in Six Thousand Six Hundred Sixty Two

220 1.00 existing M.S.housing.. 6662.97 Ea. ₹

Rupees And Paise Ninety Seven Only

Supplying and erecting, commissioning and testing of Diesel Generating set confirming to IS: 4722:1968 & BS:5514 having continuous rating,

phase, 415 volts, 50 cycles A.C. supply comprising of a totally enclosed air/water cooled diesel engine with multi-cylinders developing suitable

BHP not less than following capacity at 1500 RPM with 10% overload for one hour in 24 hours with standard accessories like fly wheel,

lubricating oil cooler, "A" class governor, heavy duty fuel wheel and lubricating oil filter, oil bath air filler, lubricating oil pressure gauge, end

exhaust manifold, standard set of tools with adjustable spanners, screw drivers, cylinder head to cover, joint cylinder head to exhaust, element

lube oil filter, 12 / 24 volts electric starting equipment complete with standard heavy duty battery, dynamo, cut-outs, ammeter, necessary

wiring, pressure gauge, starter etc and heavy duty Residential type exhaust silencer (With DEF System) and vertical hot air duct both logged

with asbestos rope, save oil trays, exhaust piping of required length, standard wall/floor mounted fuel with level indicator and piping and drip

proof alternator, self excited, self regulated, screen protected, with excitation system, capable of delivering the rated system output at

volts, 3 phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM, conforming to IS-4722- 1968 with voltage regulation +/- 5% of rated voltage from

no load to full load. Both the engine and alternator fitted on a common fabricated steel base plate with antivibration mounting engine and

alternator both connected to each other by flexible flange coupling and with floor/wall mounted control panel box comprising of voltmeter

ammeter, selector switches, ACB / MCCB / MCB of adequate capacity, indicator lamps duly wired with HRC fuses. The alternator & control

panel shall be connected with provided suitable capacity armoured cable and complete with Acoustic enclosure (canopy) made out of 16 SWG

CRCA Sheet, sound absorbing material Rockwool of 64 density & 100 mm thick conforming to IS:8183 / PU Foam of 40 Density - at least 40 mm. Twenty Four Lac Sixty Two Thousand

221 1.00 The resin bonded rockwool covered from inside the canopy by perforated sheet with 3/4 mm holes, sound level not more than 75 dB at a 2462248.70 Two Hundred Forty Eight Rupees And Ea. ₹

distance of 1 mtr, as per PVCT norms.DG set should have in built fuel tank capacity of minimum 8 hrs of continous running capacity on full load Paise Seventy Only

. Erection, commissioning and satisfactory testing as per requirement with first filling of fuel (minimum up to the 80% of fuel tank capacity), oil,

etc. with guarantee / Warrantee of complete system for Two years. & with obtaining all necessary certificate from Electrical Inspector. The

Capacity and Ratings of DG sets are as below. (As per new CPCB4+ Emission norms Engine With - Turbo Charger, EGR (Exhaust Gas

Recirculation), CRS (Common Rail Fuel System), DOC (Diesel Oxidation Catalyst), SCR (Selective Catalytic Reduction), Integrated wiring harness

connected to ECU .)

(R) Continuous rating of 250 KVA ,BHP not less than 309 BHP

Providing & erecting approved make AMF control panel suitable for following size of 3 phase, 415 V., 50 cycles, A.C. diesel generating set

complete of scope as detailed below: 1) Power module: A pair of electromechanically interlocked contactors (for mains & generator)

Overload relay for generator contactor Neutral contactor for mains and generator Power socket for connections. 2) Control and metering

module: Line voltage monitor. Generator voltage monitor Ammeter 3 items attempt start facility. Air circuit breakers/MCB/MCCB of suitable

rating for auto/manual operation. Auto/manual switch. Emergency stop push buttons. Manual start push button. frequency meter. Engine hour Two Lac Twenty Two Thousand Seven

222 1.00 meter. Two earthing studs. 3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High cylinder head 222714.09 Hundred Fourteen Rupees And Paise Ea. ₹

temperature. V belt failure. 4) Indicators with alarm Load on generator. Nine Only

5) Indicators Load on mains Engine fails to start . Emergency stop battery charger. The AMF Panel of following capacity (D) AMF Control Panel

for200 KVA/250 KVA3 phase DG Set

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and erecting metallic vitrified danger notice board as per language suggested by engineer incharge for MEDIUM VOLTAGE Sixty Nine Rupees And Paise Sixty Nine

223 7.00 installation to be erected as per IS-2551. 69.69 Ea. ₹

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall

Two Hundred Sixty Four Rupees And

224 50.00 with necessary clamps or in existing trench / pipe of following size of cables 264.62 Mtr. ₹

Paise Sixty Two Only

(B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall

Three Hundred Forty One Rupees And

225 100.00 with necessary clamps or in existing trench / pipe of following size of cables 341.38 Mtr. ₹

Paise Thirty Eight Only

(C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall

Six Hundred Forty Eight Rupees And

226 180.00 with necessary clamps or in existing trench / pipe of following size of cables 648.42 Mtr. ₹

Paise Forty Two Only

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall

One Thousand Four Hundred One

227 145.00 with necessary clamps or in existing trench / pipe of following size of cables 1401.88 Mtr. ₹

Rupees And Paise Eighty Eight Only

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall

One Hundred Forty Rupees And Paise

228 156.00 with necessary clamps or in existing trench / pipe of following size of cables 140.39 Mtr. ₹

Thirty Nine Only

(A) 4 core 4 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall

One Hundred Fifty One Rupees And

229 260.00 with necessary clamps or in existing trench / pipe of following size of cables 151.50 Mtr. ₹

Paise Fifty Only

(B) 4 core 6 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall

One Hundred Sixty Eight Rupees And

230 352.00 with necessary clamps or in existing trench / pipe of following size of cables 168.67 Mtr. ₹

Paise Sixty Seven Only

(C) 4 core 10 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall

One Hundred Eighty Four Rupees And

231 380.00 with necessary clamps or in existing trench / pipe of following size of cables 184.83 Mtr. ₹

Paise Eighty Three Only

(A) 4 core 16 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall

Two Hundred Twenty Nine Rupees And

232 232.00 with necessary clamps or in existing trench / pipe of following size of cables 229.27 Mtr. ₹

Paise Twenty Seven Only

(B) 4 core 25 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out

Thirty Three Rupees And Paise Thirty

233 9.00 going tails, insulating tape etc for following size of cables. 33.33 Ea ₹

(A) 2 to 4 core 2.5 / 4 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out

Thirty Eight Rupees And Paise Thirty

234 12.00 going tails, insulating tape etc for following size of cables. 38.38 Ea ₹

(B) 2 to 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out

Thirty Eight Rupees And Paise Thirty

235 15.00 going tails, insulating tape etc for following size of cables. 38.38 Ea ₹

(C) 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out

Forty Seven Rupees And Paise Forty

236 14.00 going tails, insulating tape etc for following size of cables. 47.47 Ea ₹

(D) 2 to 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured

Seventy Five Rupees And Paise Seventy

237 5.00 cable complete with out going tails, insulating tape etc for following size of cables. 75.75 Ea ₹

(B) 3 & 1/2 core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured

One Hundred Forty Rupees And Paise

238 9.00 cable complete with out going tails, insulating tape etc for following size of cables. 140.39 Ea ₹

Thirty Nine Only

(E) 3 & 1/2 core 120 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured

Two Hundred Forty Seven Rupees And

239 4.00 cable complete with out going tails, insulating tape etc for following size of cables. 247.45 Ea ₹

Paise Forty Five Only

(H) 3 & 1/2 core 240 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

240 70.00 connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 6.06 Six Rupees And Paise Six Only Ea. ₹

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

Thirteen Rupees And Paise Thirteen

241 60.00 connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 13.13 Ea. ₹

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

242 55.00 connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 15.15 Fifteen Rupees And Paise Fifteen Only Ea. ₹

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

243 18.00 connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 20.20 Twenty Rupees And Paise Twenty Only Ea. ₹

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

Forty Five Rupees And Paise Forty Five

244 24.00 connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 45.45 Ea. ₹

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

Eighty Five Rupees And Paise Eighty

245 13.00 connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 85.85 Ea. ₹

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation suitable for following type of applications with chamber and

heavy duty cover. (A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate)

& having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-

2017, Voltage drop:-

< 1 volt at no load & dry form, Sulphar content:- Eight Thousand Six Hundred Thirty Six

246 22.00 <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test report must 8636.51 Ea ₹

Rupees And Paise Fifty One Only

be submitted by Agency.

(c) For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer

System(like Automation, SCADA) i.e independent Earthing in normal soil.

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using Seven Hundred Ninety Four Rupees

247 35.00 copper clamp. 794.87 Kg. ₹

And Paise Eighty Seven Only

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. Seventy Seven Rupees And Paise

248 35.00 using proper clamp. 77.77 Kg. ₹

Seventy Seven Only

Providing and erecting Annealed bare Copper wire 4.064mm to 1.626mm. Seven Hundred Ninety Four Rupees

And Paise Eighty Seven Only

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C.

One Thousand Nine Hundred Forty

Hz 1200 mm sweep complete having 3blades with aluminium blades with , canopy & 30 cm. down rod erected with earthing.(Make

250 140.00 1948.29 Eight Rupees And Paise Twenty Nine Ea ₹

shall be approved by Engineer in charge))

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete One Hundred Eight Rupees And Paise

251 140.00 with proper insulation without leakage and earthing. 108.07 Mtr. ₹

Supplying & erecting fan hook box of 10 mm

M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a One Hundred Eight Rupees And Paise

252 150.00 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing. 108.07 Ea ₹

Providing 2.5mm.thick laminated acrylic sheet Eighteen Rupees And Paise Eighteen

253 150.00 to cover the fan hook or Fan box. 18.18 Ea. ₹

Supplying & erecting approved make low noise decorative exhaust fan having square frame ABS body with inbuilt lowers & square frame.

One Thousand Three Hundred Sixty Six

254 50.00 200mm with 1350RPM Cat.II 1366.53 Ea ₹

Rupees And Paise Fifty Three Only

Providing recess in wall or window frame suitable for erection of Exhaust fan complete with plastering and colour washing to match

the colour of the wall or window complete with expanded metal in order to render the fitting in accessible and the room water-proof. One Hundred Eighty Nine Rupees And

Paise Eighty Eight Only

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 % Five Hundred Thirty Five Rupees And

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer Paise Thirty Only

incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum 15000 burning hours life, 500 V

in built-surge protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf >=

(A) LED Lamps integral type, with PC diffuser One Hundred Twelve Rupees And Paise

257 150.00 suitable LAMP holder 112.11 Ea ₹

(ii) 5 to 8 watts cat III

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with diffuser housed in aluminium casted body with company mark/name 160V

to 270V,Power Factor more than 0.95, THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % (

fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) Five Hundred Eighty Nine Rupees And

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting clips complete.IP20 Paise Eighty Four Only

(iii) 16-20 watts, Surge-2 KV cat - III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with diffuser housed in aluminium casted body with company mark/name 160V

to 270V,Power Factor more than 0.95, THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % (

fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

One Thousand Seven Hundred Ninety

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

259 40.00 1794.77 Four Rupees And Paise Seventy Seven Ea ₹

(B) LED Panel Light with provision for Plane

front frame with translucent cover fixed to housing complete.IP20

(vi) 36 watts, 24" x 24", Surge- 2KV cat - III

Providing & Erecting full SS Body (SS 304) Split type water cooler having storage capacity 160 to 175 Ltr.(Tank SS 304) & Cooling capacity 150 ltr.

Per hour @ an ambient temp of 350 C.The outlet temp. of the water should drop by 150C within a hour,The water cooler should be comprising

of hermetically sealed Reciprocating compressor with R134A, fan motor, Copper Condensing unit with company fabricated Outdoor Unit water

tank surrounded by evaporating coil, thermostats, relay etc.complete with necessary copper tube & Insulation, M.S Chanel Stand with Painting Sixty Seven Thousand Two Hundred

260 3.00 for water tank & M.S. Powder Coated Stand for Outdoor unit with Installation. With DPELCB and 4 Way DB Box with accessory Three core Cord 67226.61 Twenty Six Rupees And Paise Sixty One Ea. ₹

for connection. Only

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring

presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 psi inline type post carbon filter auto low & Twenty Nine Thousand One Hundred

261 3.00 high pressure switches with following size of storage tank & LPH capacity & erected as directed[C] 50 Ltr / Hr with 150 psi 2 nos booster pump 29187.99 Eighty Seven Rupees And Paise Ninety Ea. ₹

Supplying and erecting approved make Instantaneous type water heater with 3Itr.capacity rust free container housed in

ABS plastic body insulated with glass wool / puff insulation and 3 Kw heating elements,adjustable thermostat 300 C

Five Thousand Six Hundred Thirty Nine

262 8.00 to 850 C with set to operate at 850 C (+ /-60 C ) auto reset indication lamps, thermal cut-out, safety valve fusible plug etc. Premium 5639.84 Ea. ₹

Rupees And Paise Eighty Four Only

Supplying and erecting horizontal / vertical mounting type storage water heater with copper container housed in M.S./S.S./ABS body insulated

with glass wool/puff complete with heating elements,adjustable thermostats 300C to 850C, indicating lamp, safety valve, fusible plug,

etc.complete erected with coach bolts, nuts. washers & cementation (B)15 Ltr-.with 2 /3K.W. heating element Premium Category Nine Thousand Five Hundred Thirteen

Rupees And Paise Nineteen Only

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base

Two Thousand Five Hundred Seventy

264 170.00 complete as required. 2571.46 Ea ₹

One Rupees And Paise Forty Six Only

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete

Two Hundred Sixty Two Rupees And

265 170.00 with all connections etc as required. 262.60 Ea ₹

Paise Sixty Only

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Three Thousand Four Hundred Seventy

Eight Rupees And Paise Forty Four Only

Supplying, installation, testing & commissioning of intelligent addressable programmable sounder complete as required.

Two Thousand Three Hundred Eighty

Five Rupees And Paise Sixty Two Only

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel

wire armouring & FRLS/HFFR outer sheath complete as required One Hundred Sixty Four Rupees And

Paise Sixty Three Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Supplying, installation, testing & commissioning of repeater panel with 320 character/ Touch screen LCD display with inbuilt reset, acknowledge Ninety Seven Thousand Three Hundred

269 2.00 and silence switches complete as required. 97348.85 Forty Eight Rupees And Paise Eighty Ea. ₹

Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing

unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per

loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other

keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), 48 hrs back-up with

24 volt sealed maintenance free batteries with automatic charger. 211 DELHI SCHEDULE OF RATES (E&M)-2025 The panel shall have facility to

connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the

Two Lac Fourteen Thousand Three

schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open

270 1.00 214343.21 Hundred Forty Three Rupees And Paise Ea ₹

protocol BACnet/ Modbus over IP complete as per specifications.Two Loop Panel.

Twenty One Only

Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger with

IGBT base rectifier & Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160-270V

AC & inverter having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage output with over load &

short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with Three Lac Ninety Seven Thousand

271 1.00 MS painted batteries stand, 10% Overload capacity for momentary load. 397324.91 Three Hundred Twenty Four Rupees Ea ₹

(J) 20 KVA 3 - phase with 1Hr Backup And Paise Ninety One Only

Supplying submersible pump set suitable for bore of 100 mm. dia. or more having three phase motor capacity not more than 5 H.P. with Twenty Four Thousand Six Hundred

272 2.00 following capacity. (B) (16 stage) 140 to 180 LPM discharge at 96 to 69 mtrs. head respectively suitable for 50mm dia. delivery pipe cat III 24611.68 Eleven Rupees And Paise Sixty Eight Ea ₹

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

One Hundred Seventy Two Rupees And

Paise Seventy One Only

Providing & erecting open well type horizontal mono block pump set with stainless steel body having following specification (C) 1 H.P. single

phase open well motor pump set suitable for 185 LPM discharge @ 25 mtr. head, suitable for 32 mm dia. Delivery pipe with control panel. Ten Thousand Five Hundred Seventy

Cat III Four Rupees And Paise Seventy Only

Providing & erecting open well horizontal mono block pump set with cast iron body, complete for three phase submersible motor having [D]

For 5 HP 3 phase open well horizontal mono block pump set suitable for 1350 LPM to 310 LPM @ 10 to 42 Mtr head suitable for 50/65 Twenty Thousand Six Hundred Twenty

mm dia delivery pipe One Rupees And Paise Seventeen Only

Supplying & erecting approved make Automatic liquid level controller 6A. with sensor testing as per instruction of Engineer in charge on site

Two Thousand Three Hundred Fifty

276 3.00 complete with wiring connection with existing wires , with copper conductor from pump to upper and lower tank. 2355.32 Ea. ₹

Five Rupees And Paise Thirty Two Only

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted inside

and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter (in a

single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection, over voltage

(Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for setting of all

parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED display for any

fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop push buttons to Seven Thousand Two Hundred Fifty

be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only) Rupees And Paise Seventy Nine Only

(A) DOL up to 5.0 H.P.

Supplying and erecting approved make Conical Pole (Standard ) Made from HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759 with required base plate and integral Junction box consist of terminal plate of min

6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable terminationas

erected on suitable foundation (included) with necessary GI nut-bolts/J-Bolts. as per details given by manufacturer considering site Six Thousand Four Hundred Three

requirement.The length of poles are as below. Rupees And Paise Forty Only

(C) 5 Mtr. Long 65mm Top X140 mm bottom dia, 3mm thickness.

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and erecting street light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with

suitable B Class M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top having

sufficient fasteners for fixing the brackets and having spread of 1 mtr. length with suitable rise as per site condition & suitable welded

Five Hundred Sixty One Rupees And

279 20.00 stiffener reducer and nipple with check nut complete painted with one coat of Red oxide / PU base primer and two coats of 561.56 Ea ₹

Paise Fifty Six Only

Aluminium / PU paint. paint with following nos of arms.

[A] Single Arm bracket 1 Mtr

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop- out approx. 2mm thick box complete

with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as per requirement having locking

arrangements with mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of Eight Hundred Ninety Eight Rupees

280 20.00 following size of box. 898.90 Ea ₹

And Paise Ninety Only

(A) 300mm x 200mm x 100mm [deep]

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 3 Watt and above assembled on

single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer

Four Thousand Two Hundred Forty

281 20.00 incharge may select any wattage capacity between the ranges shown.) 4248.06 Ea ₹

Eight Rupees And Paise Six Only

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection.

(ii) above 48 to 60 Watts Cat-lll

Providing and fixing Terminal board of size 5.0 x 127 x 152.4 mm.bakelite sheet with suitable brass studs with nuts, washers and clamps

of size 25mm x 3mm suitable for pole painted with one coat of red lead paint. One Hundred Forty Six Rupees And

Paise Forty Five Only

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup

1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup

time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof Three Thousand One Hundred Sixty

283 1.00 thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed. 3168.37 Eight Rupees And Paise Thirty Seven Ea ₹

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction Cat III One Thousand Eight Hundred Eighty

Three Rupees And Paise Sixty Five Only

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected

Fifty Eight Rupees And Paise Fifty Eight

285 100.00 as directed. (e) 1.50 Sq.mm 3 core round PVC sheathed 58.58 Mtr. ₹

Supplying and erecting B class Galvanized iron pipe having smooth finished bore of the pipe on both ends erected nuts and bolts along the Two Hundred Forty Nine Rupees And

pole / wall shaping the pipe as per site requirement. Pipe dia as following. (C) 40 mm dia. Paise Forty Seven Only

Providing and erecting Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially

Nine Hundred Ninety Four Rupees And

287 20.00 prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel) For using salt and charcoal / coke as required 994.85 Ea. ₹

Paise Eighty Five Only

for pipe type earthing.

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II

)with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road One Hundred Eight Rupees And Paise

surface for enclosing cable Seven Only

(A)50 mm outer dia

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for laying any size of cable or locating the Seventy Four Rupees And Paise

fault all over the run and back filling the same and making the surface as normal ground. Seventy Four Only

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the fault all over the run and back filling the same Fifty Five Rupees And Paise Fifty Five

and making the surface as normal ground. Only

Supplying & erecting IP 55 grade following size section pillar fabricated from joint less M.S. Sheet with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground to have appropriate erection to work uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc. hinged double door internally supported on both side, with internal and outside looking

arrangement with lock and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and other with nut and bolt for erecting

Bakelite sheet. Painting the Section Pillar inside and out side with three tank powder coated paint. section pillar roof should be without joint Three Thousand Five Hundred Ninety

with water leakage proof & tested as per IP 55 test & followed by IS 2147 of 1962(B) 75 X 60 X 45 cm section pillar fabricated from 16 Gauge Five Rupees And Paise Sixty Only

MS Sheet with angle iron legs 45 cm long made from 35 X 35 X 5 mm thick MS angle.

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The cable tray should be single or double bended as

per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support( included) as per Specification and Three Hundred Sixty Rupees And Paise

as per instruction of engineer in charge. (2) 100 X 50 X 1.6 mm Thick Fifty Seven Only

Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The cable tray should be single or double bended as

per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support( included) as per Specification and Four Hundred Twenty Four Rupees And

as per instruction of engineer in charge.(3) 150 X 50 X 1.6 mm Thick Paise Twenty Only

Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The cable tray should be single or double bended as

per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support( included) as per Specification and Six Hundred Twenty Two Rupees And

as per instruction of engineer in charge. (5) 300 X 50 X 2.0 mm Thick Paise Sixteen Only

Providing and erecting Inverter based approved make split air-conditioning unit consisting of condensing unit with variable speed fan motor,

inverter type hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower

motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includes Eco Friendly Thirty Nine Thousand One Hundred

295 1.00 green gas charging and 15A plug top & Remote Control & MS Stand) with necessary core cutting. 39126.39 Twenty Six Rupees And Paise Thirty Ea. ₹

(2)For ISEER Range (KWH/KWH)(4.0 to 4.49) (A) for 1.0 ton capacity Nine Only

Providing and erecting Inverter based approved make split air-conditioning unit consisting of condensing unit with variable speed fan motor,

inverter type hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower

motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includes Eco Friendly Forty Five Thousand Eight Hundred

296 4.00 green gas charging and 15A plug top & Remote Control & MS Stand) with necessary core cutting. 45898.44 Ninety Eight Rupees And Paise Forty Ea. ₹

(2)For ISEER Range (KWH/KWH)(4.0 to 4.49) (B) for 1.5 ton capacity Four Only

Providing and erecting Inverter based approved make split air-conditioning unit consisting of condensing unit with variable speed fan motor,

inverter type hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower

motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includes Eco Friendly Fifty Six Thousand Eight Hundred Thirty

297 3.00 green gas charging and 15A plug top & Remote Control & MS Stand) with necessary core cutting. 56833.71 Three Rupees And Paise Seventy One Ea. ₹

(2)For ISEER Range (KWH/KWH)(4.0 to 4.49) (C) for 1.7 to 2 ton capacity Only

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit consisting of condensing unit with fan

motor, hermetically sealed scroll/rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower

motor with its accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star and above of current Seventy Six Thousand Three Hundred

year) with necessary core cutting. (A) for 1.5 ton capacity Five Rupees And Paise Fifty Only

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit consisting of condensing unit with fan

motor, hermetically sealed scroll/rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower Eighty Eight Thousand Eight Hundred

299 8.00 motor with its accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star and above of current 88804.25 Four Rupees And Paise Twenty Five Ea. ₹

year) with necessary core cutting. (B) for 2 ton capacity Only

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and control cable,necessary PVC drain pipes for

One Thousand One Hundred Fifty Eight

300 140.00 Split AC machine up to 4 TR capacity 1158.47 Rmt. ₹

Rupees And Paise Forty Seven Only

Providing and erecting approved make ductable split Air Conditioning unit each consist of remote located condensing unit and an

evaporating unit complete with interconnecting insulated refrigerant piping up to 10 RMT. rigid PVC, drain piping of 10 kg / cm2 dully

One Lac Sixty Four Thousand Nine

insulated with nitrile rubber insulation of 10 RMT with ECO Friendly Green gas. The condensing unit is complete with hermetically sealed

301 2.00 164949.16 Hundred Forty Nine Rupees And Paise Ea. ₹

scroll compressor & condenser unit which effectively achieves heat rejection by utilizing air of fan and coil type condenser. The

evaporating unit will be complete with DX evaporator centrifugal blower, blower motor along with microprocessor biased remote controller

with memory backup etc. (A) For 5.5 Ton

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as per Seven Thousand Seventy Three Rupees

specifications and size & shape as per site requirement and approved design. And Paise Three Only

Supply and installation of Canvas Connection connecting machine's outsource of cool air to ducting Three Thousand Two Hundred Thirty

Two Rupees Only

Extra charges for the refrigerant piping beyond standard length For ductable A.C. Machine 18 Gauge hard drawn copper pipe including

Six Hundred Fourteen Rupees And

304 60.00 necessary fittings i.e. elbows, couplings, reducers etc. For Suction/ Hot Gas/ Liquid Line (C.) 12.7 mm dia (OD) (Soft drawn) with tube thickness 614.08 Mtr ₹

Paise Eight Only

1.2 mm with 19 mm thick insulation

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Extra charges for the refrigerant piping beyond standard length For ductable A.C. Machine 18 Gauge hard drawn copper pipe including

Seven Hundred Ninety Six Rupees And

305 70.00 necessary fittings i.e. elbows, couplings, reducers etc. For Suction/ Hot Gas/ Liquid Line (D) 15.86 mm dia (OD) (Soft drawn) with tube thickness 796.89 Mtr ₹

Paise Eighty Nine Only

1.2 mm with 19 mm thick insulation

Extra charges for the refrigerant piping beyond standard length For ductable A.C. Machine 18 Gauge hard drawn copper pipe including

Nine Hundred Forty Rupees And Paise

306 80.00 necessary fittings i.e. elbows, couplings, reducers etc. For Suction/ Hot Gas/ Liquid Line (E) 19 mm dia (OD) (Hard drawn) with tube thickness 940.31 Mtr ₹

Thirty One Only

1.2 mm with 19 mm thick insulation

Extra charges for the refrigerant piping beyond standard length For ductable A.C. Machine 18 Gauge hard drawn copper pipe including

One Thousand One Hundred Fifty Five

307 50.00 necessary fittings i.e. elbows, couplings, reducers etc. For Suction/ Hot Gas/ Liquid Line (F) 22.2 mm dia (OD) (Hard drawn) with tube thickness 1155.44 Mtr ₹

Rupees And Paise Forty Four Only

1.2 mm with 19 mm thick insulation

Extra charges for the refrigerant piping beyond standard length For ductable A.C. Machine 18 Gauge hard drawn copper pipe including

One Thousand Three Hundred Sixty

308 30.00 necessary fittings i.e. elbows, couplings, reducers etc. For Suction/ Hot Gas/ Liquid Line (G) 25.4 mm dia (OD) (Hard drawn) with tube thickness 1362.49 Mtr ₹

Two Rupees And Paise Forty Nine Only

1.2 mm with 19 mm thick insulation

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.25 mm dia.25mm One Hundred Five Rupees And Paise

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation. 40 mm dia. One Hundred Thirty Rupees And Paise

Twenty Nine Only

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene

One Thousand Three Hundred Eight

311 70.00 rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet 1308.96 Sq.mt ₹

Rupees And Paise Ninety Six Only

thickness complete as required. (A) Thickness 0.63 mm sheet (22 Gauge)

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene

One Thousand Five Hundred Nineteen

312 70.00 rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet 1519.04 Sq.mt ₹

Rupees And Paise Four Only

thickness complete as required. (B) Thickness 0.80 mm sheet (20 Gauge)

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers complete as per Ten Thousand Four Hundred Thirty

313 8.00 specifications and size & shape as per site requirement and approved design. 10431.28 One Rupees And Paise Twenty Eight Sq.mt ₹

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of

required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure

Twelve Thousand Twenty Four Rupees

314 8.00 automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not 12024.05 Sq.Mtr. ₹

And Paise Five Only

externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. (A) Fire

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of

required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure

Eleven Thousand Two Hundred Sixty

315 8.00 automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not 11264.53 Ea. ₹

Four Rupees And Paise Fifty Three Only

externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. (B)

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation

Eight Hundred Seventy Seven Rupees

316 80.00 on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self 877.69 Sq.mt ₹

And Paise Sixty Nine Only

adhesive nitrile rubber tape insulation complete as per specifications and as required. 19 MM

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation

One Thousand One Hundred Two

317 80.00 on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self 1102.92 Sq.mt ₹

Rupees And Paise Ninety Two Only

adhesive nitrile rubber tape insulation complete as per specifications and as required. 25 MM

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with

mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick Eight Hundred Twenty Six Rupees And

perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as Paise Eighteen Only

required and as per specifications.

Supplying Installation Testing and Commissioning of 4MP IP IR Dome Camera having following specifications and features etc :- 1) Signal

System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date & Time in live & recorded video 2)Image Sensor:

1/2.8" or better progressive Scan CMOS to get color image even at night condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with

IR or better) True Day & Night High Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR LED's

with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter support,

Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. 3) Compression

(Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 4) Wide Dynamic Range:- WDR (120dB or more) 5) Digital

Noise Reduction:- DNR (3D) On/Off 6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP

(2560×1440)25/30fps , Sub streams minimum: 720P@25/30 fps 7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness

adjustable through client software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection 8) Cyber Security: AES 256-bit

Encryption, Configuration encryption, trusted execution, Digest, security logs, account lockout, video encryption, IP/MAC filtering, HTTPS,

trusted upgrade 9) Onboard Storage: Camera should support built-in Micro SD/ SDHC/ SDXC Card slot upto 512 GB. It should be supplied with

minimum 128GB memory Card. 10) Recording Management: Format SD, overwrite, storage management, video to NAS device, 11) Alarm

Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space

detection 12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP,

RTSPS,20) IR life: 40000 hours or higher 21) Video Bit rate: 32 KBPS - 8 MBPS or better 22) Standards: BIS with ER, STQC Certified, CE, FCC and

RoHS unicast, 13) System Capability: ONVIF, Camera shall support open source VMS 14) Ethernet: 1 RJ 45 10/100 Ethernet port 15) Audio : It

should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per site requirement. 16) Power Input: The camera

should support simultaneous dual power input—12 VDC (via power adapter) and PoE (802.3af)—to ensure continuous operation in the event of

a failure in one power source. 17) Power Requirement: 12VDC/24 VDC/PoE (802.3af)/ePoE 18) Housing/ Enclosure:- IP67 weather proof, IK10,

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

a failure in one power source. 17) Power Requirement: 12VDC/24 VDC/PoE (802.3af)/ePoE 18) Housing/ Enclosure:- IP67 weather proof, IK10,

Metallic body 19) Operating Condition:- Ambient Temperature:- (- )05°C to 50°C, humidity 95% (max) (non-condensing) 20) IR life: 40000 hours

or higher 21) Video Bit rate: 32 KBPS - 8 MBPS or better22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS4MP @ 25/30fps@1440P

(2560 x 1440) Dome Camera with 2.8/ 3.6/ 6/8/12 mm fixed lens (as per site requirement).

4MP @ 25/30fps@1440P (2560 x 1440) Dome Camera with 2.8/ 3.6/ 6/8/12 mm fixed lens (as per site requirement).

Eight Thousand Eight Hundred Seventy

One Rupees And Paise Eighty Four Only

Supplying Installation Testing and Commissioning of 4MP IP IR Outdoor Bullet Camera having following specifications and features etc :- 1)

Signal System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date & Time in live & recorded video 2)Image

Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux

with IR or better) True Day & Night High Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR

LED's with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter

support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. 3)

Compression (Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 4) Wide Dynamic Range:- WDR (120dB or

more) 5) Digital Noise Reduction:- DNR (3D) On/Off 6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP

(2560×1440)25/30fps Sub streams minimum: 720P@25/30 fps 7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness

adjustable through client software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection 8) Cyber Security: AES 256-bit

Encryption, Configuration encryption, trusted execution, Digest, security logs, account lockout, video encryption, IP/MAC filtering, HTTPS,

trusted upgrade 9) Onboard Storage: Camera should support built-in Micro SD/ SDHC/ SDXC Card slot upto 512 GB. It should be supplied with

minimum 128GB memory Card. 10) Recording Management: Format SD, overwrite, storage management, video to NAS device, 11) Alarm

Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space

detection 12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP,

RTSPS, unicast, 13) System Capability: ONVIF, Camera shall support open source VMS 14) Ethernet: 1 RJ 45 10/100 Ethernet port 15) Audio : It

should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per site requirement. 16) Power Input: The camera

should support simultaneous dual power input—12 VDC (via power adapter) and PoE (802.3af)—to ensure continuous operation in the event of

a failure in one power source. 17) Power Requirement: 12VDC/24 VDC/PoE (802.3af)/ePoE 18) Housing/ Enclosure:- IP67 weather proof, IK10,

Metallic body 19) Operating Condition:- Ambient Temperature:- (- )05°C to 50°C, humidity 95% (max) (non-condensing) 20) IR life: 40000 hours

or higher 21) Video Bit rate: 32 KBPS - 8 MBPS or better 22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

4MP @ 25/30fps@1440P (2560 x 1440) Outdoor Bullet Camera with 2.8/ 3.6/6/8/12 mm fixed lens (as per site requirement)

Eight Thousand Six Hundred Thirteen

Rupees And Paise Twenty Eight Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Supplying Installation Testing and Commissioning of following Channel Network Video Recorder (NVR) with camera licenses to record for all

channels having specifications and features etc as mentioned below : 1) Network Video Recorder Embedded/ Installed OS (Linux) along with

Camera Licenses to record per NVR and to provide a live view, storage and simultaneously Multi-channel playback of all IP camera or more and

must be ONVIF with minimum support of 384 Mbps incoming Bandwidth. 2) NVR should support video compressions : H.265 or better, H.264,

MJPEG. 3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with G.711U/A, G.711u, PCM, G726 audio compressions.

4) Intelligent auto power on when power resumes after power outage. 5) Storage: It should support minimum 8 SATA Slots with 20TB capacity/

Slot and RAID support of RAID 0/1/5/6/10. 6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232, 1x eSATA

Port 7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0) 8) Video Output Ports: 2x HDMI and 2 VGA 9) Alarm Ports: It

should have 16/8 Ch In/ Out ports to connect various type of external sensors and output devices like hooter/ Siren etc. 10) Email & SMS Altert

options: Option for SMS/ Email Alerts to minimum 5 designated mobile number for power failure, HDD failure, vandalism, tempring, network

disconnection and panic 11) Web & Mobile Application: Web, Mobile app ( For iPhone, iPad, Android Phone) for alerts and viewing. 12)

Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP Filter, PPPoE, FTP, DDNS, Alarm Server, IP Search, Multicast, Auto

Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and OEM Cloud for remote monitoring without any public IP need. 13) Standards:

CE, FCC, RoHS, BIS Certified 14) Power Supply : Should support AC100-240V, 50/60Hz Power supply. 15) Operating Condition : -5°C to 50°C,

humidity 90% (max) (non-condensing) 16) The VMS application shall support all the features & functionalities of the offered cameras. 17) VMS

should consist Licenses for all channels to record Cameras with General, motion detection, intelligent, alarm and POS recording modes. VMS

should be provided with Camera Licenses , with no dependency of VMS licenses by binding with the MAC address of the cameras to achieve the

functionality. 18) The NVR OEM shall be responsible for providing a mobile application compatible with both Android and iOS devices, enabling

remote monitoring and playback of cameras/NVR footage. 19) The OEM must provide its own DDNS server hosted in India, eliminating the

need for a public IP address for remote monitoring over the Internet. 20) Must support Continuous, Alarm, Motion, Instant, Panic Recording

Mode 21) It should support Resolution: 32MP; 24MP; 16MP; 12MP; 8MP; 5MP; 4MP; 1080p; 720p; D1; CIF; QCIF 22) When alarm recording is

enabled and an event occurs, you can click the alarm icon on monitoring page to view the alert details. The snapshot function is supported on

monitoring and playback page 23) The Network Video Recorder (NVR) shall be configured to send email whenever a system message is created

or an alarm event occurs. The email server shall be a valid SMTP server. Each recipient email address shall be configured to receive any

combination of critical, warning, or informational messages or alarm notifications. When an alarm occurs, the email message includes the NVR

name, time of alarm and a list of camera that is configured to record upon alarm 24) It should have Web and GUI interface. 25) Built-In Artificial

Intelligence: NVR should have built-in AI :- - 2 Channel face detection and recognition, - Minimum 4 Channel perimeter protection, - Minimum

Channel Smart Motion Detection 26) Face Recognition Database Capacity: It should support total Blacklist and Whitelist capacity of Minimum

20,000 Faces or more with Face Detection speed of 12 face images/sec and facility to add Name, gender, birthday, address, credential type,

credential No., countries & regions and state to each face image. 27) Face & Human Attributes Search: Search Pictures/ Video by Gender, age

group, glasses, expressions, face mask, beard, Top color, top type, hat, bag, age, gender and umbrella. 28) ANPR Capability: It should support

ANPR Camera with License plate, plate color, vehicle body, vehicle model, vehicle logo, calling, seatbelt, vehicle registration location etc vehicle

attributes. 29) Alarm Notifications based on: Motion detection, video tampering, video loss, scene changing, PIR alarm, Camera external alarm,

Face detection, face recognition, perimeter protection (intrusion and tripwire), ANPR, people counting, stereo analysis, crowd distribution, heat

map, Disk Full, Storage Error, IP Conflict and abnormal behavior of fan, cybersecurity exception 30) Alarm Notification should be linked with

Recording, snapshots, Camera external alarm output, buzzer, logs, presets and email. 31) General AI Based Search: Search Pictures by channel,

time, event type, target classification (Fall Detection, People Approach Detection, People No. Exception Detection, People Staying Detection,

Violence Detection. 32) Smart playback function: Should support smart search for the selected area in the video and smart playback to improve

the playback efficiency 33) VCA (Video Content Analytic): Should support multiple video contented analytics based on camera analytics 34)

Analytics by NVR: Perimeter protection and face recognation

32 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16/25/32(36), 2nd screen: 1/4/8/9/16

Fifty Five Thousand Four Hundred Fifty

One Rupees And Paise Two Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Supply, Installation, Testing and commissioning of 42/43" UHD Signage/Professional Display|500 Nits Brightness |50000:1 Contrast Ratio |

Operation: 24x7|1xVGA; 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0 (Internal), RJ45, RJ12, RS232, Optical SPDIF|1xHDMI 2.0 out, Supports

Daisy Chain |Speaker 2x10 W|30-degrees Tilting Installation | Open Content Management Support, Scheduler, USB-Autoplay, AutoLaunch,

HDMI-CEC, HDMI-Wakeup, Auto-switch on Failover, Panel Lock, OSD Rotation, NoSignalPowerOff, Screen Saver, Pixel shift,Scheduler, Videowall

Fifty Two Thousand Three Hundred

322 1.00 support, Remote control via LAN, Realtime Clock, Joystick, Rocker Switch| Optional : SDM or OPS compatibility, Embedded IR, IR extender 52318.00 Ea. ₹

Eighteen Rupees Only

option | Optional: Overlay Touch Kit Compatibility|Certifications: Safety, EMC, CE [Sony, Samsung, LG, Panasonic]

SITC of 24 x 10/100/1000BASE-T PoE ports 4 x Gigabit RJ45/SFP Combo ports Advanced L2 switching and security features L2+ Static Routing Thirty One Thousand Nine Hundred

323 1.00 Optional “standard mode” or “surveillance mode” management user interface 193 W PoE budget [Approved by Competent Authority i.e. not 31996.80 Ninety Six Rupees And Paise Eighty Ea. ₹

Below the rank of Executive Engineer ] Only

Supplying, Installation, Testing and Commissioning following capacity Serveillance grade Hard Disk with upto 256MB/s Transfer Rate, 256 MB

Cache, 7200 RPM Disk Speed, 3.5 inch form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB- Fourteen Thousand Sixteen Rupees

324 1.00 Scheme, TUV, UL Certifications.6TB (Terabytes) 14016.78 Ea. ₹

And Paise Seventy Eight Only

Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm CRCA Sheet, completely knocked-down condition

(CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking, Minimum 2 cable entry/exit provision at Top and bottom with rubber protection,

Front 5mm Toughened Glass with lock, wall mounting kit, Powder coated Color- RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power Seven Thousand Six Hundred Sixty

325 1.00 distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc. complete as required.9U Rack 7669.94 Nine Rupees And Paise Ninety Four Ea. ₹

(a) General Features & Special Features of the all lift items shall be taken as below.(d) The Rates of the following items are for the lift of

Machine room less. For Machine room Lifts, rate for Rs. 1,50,000/- shall be deducted in Total Cost for the Lifts from 4 to 13 Passenger Lift. Rs.

2,00,000/- shall be deducted in Total Cost for the Lifts 15 and above passenger capacity as extra cost.(A) GENERAL DESCRIPTION OF LIFTS. [1]

GEAR LESS LIFT DRIVE (MRL) comprising of High Starting torque Lift 3 phase 440 V A. C. Permanent Magnet Synchronous motor of proper rating

with high efficiency shall be used.[2] Micro processor based / PLC, ACVVVF, vector control drive with encoder feedback closed loop system shall

be used for lift car and door operation which shall be full collective selective operation hall call demand response, UP/DOWN hall stops, Main,

Up/ Down Contactor with overload and phase reversal relay and safety controls. [3] Car with M S platform with bracings of adequate size and

to sustain the impact load cabin + passenger with safety factor of fire for steel and side panels of Stainless steel of sheet of grade 304 duty. Car

ceiling will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car flooring shall be of anti skid PVC with choice of colour of

engineer in charge. Car doors shall be of stainless steel grade 304, hairline finish with centre opening / telescopic automatic doors. Car panel

will also be S.S. 304 finished with emergency stop device, mechanical door safety device, facility of auto/ attended mode. All car panel buttons

and all floor switches must be with brail language as per lift act.[4] All landing doors must be fire rated for 2 hour shall be fully automatic centre

opening/ telescopic opening made of hairline finish steel grade of 304 with key holes and infrared curtains with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car along with alarm switch shall be provided. Also, Emergency Light & Fan should start

immediately without any Time Delay as soon as power fails.[6] Digital scrolling indicator system for up-down arrow along with floor position

indicator shall be provided inside the car and at all floors.

[7] Full height infra red curtain with multiple cross / crossing light beams shall be provided.[8] Automatic Rescue Device (ARD) shall be provided

accordingly of passenger capacity with Manual Rescue Operation ( Manual Cranking Facility). [9] Audio visual indication in the lift car showing

over loading shall be provided such that doors kept open till excess load is removed.[10] Spring buffers/PU Buffers shall be provided. [11] Car

fan as per passenger capacity with automatic sleep timer shall be provided. [12] Voice annunciator with suitable music shall be provided in lift

car. [13] Self diagnostics system for operational and safety parameters shall be provided in control panel.[14] Mechanical over speed governor

with governor calibration as per actual site parameters and submission of calibration certificate submission, door key holes in the floor doors,

fireman switch shall be provided. [15] Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be

provided by the lift agency, along with the other steel structure works, foundations for the machine etc…[16] In the hoist way fascia plate shall

be provided without any extra cost, where ever required as / if directed by engineer in charge.

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

[17] Permanent wiring with necessary safety devices like RCCB in all circuit, Over Voltage Under Voltage protection and THD eliminator in

circuit for lift machine room and lift well with proper numbers of light points, with fixtures, exhaust fan and plug points shall be provided by

the agency. Only 3 phase Power Supply shall be made available by department in lift machine room. Necessary Earthing as per Lift Act/Rules

shall be arranged by Lift Agency.

[18] Any civil/ electrical works for additional and alteration in lift shaft and machine room related to erection of lift shall be made by lift agency

without any extra cost. (granite/marble fixing around all landing door openings are not in lift agency’s scope.) [19] Agency has to provide all

working drawings and documents and liaison services for obtaining all necessary permission from lift inspector and other authorities. [20]

acrylic transparent licence/display A4 size holder in lift car. "[20A] As per statutory requirement of Govt. Of Gujarat lift & escalator act 2000, lift

agency has to provide 1. Car top safety barricade 2. Push & talk communication system. 3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after lift erection and provide report by third party authorized by concern licensing authority

5.agency has to provide third party insurance upto completion of free maintenance period and submit the document for the same.""[21] Car

Panel Operating Buttons with floor position indicator/buttons must be of Auto Glow type clearly visible when view from inside cabin. [22] For

Physically Handicapped person Full Length Handrails of hairline finish steel grade of 304 should be provided at appropriate height on the Rear

& Side Wall Panels in Lift Car."

Supplying, Erecting, Testing & Commissioning the passenger / stretcher lift having following main features: 26 passengers . Ground plus

upper floors with Rated Speed of 1.0 m/sec with micro price/PLC control and ACVVVF. drive . Prem. Cat. (C) With General PLUS ADDITIONAL Twenty Two Lac Forty One Thousand

326 1.00 SPECIAL FEATURES attached herewith. Prem. Cat. 2241436.44 Four Hundred Thirty Six Rupees And Ea. ₹

Paise Forty Four Only

Providing, erecting, testing & commissioning approved make oil immersed ONAN cooled, double wound, core type indoor / outdoor copper

wound 11KV/ 433V step down transformer of following capacities operating on 3 phase, 50 Hz 4 wire & neutral earthed system continuously

rated for a full temperature rise in oil not exceeding 45 Deg.C.at maximum ambient temp. of 50 Deg. C. complete with necessary radiator first

filling of new transformer oil & standard fitting as below complying with IS 1180( Part 1 ):2014 standards with energy efficiency level 2 Off load

tap changing range steps +2.5% to -5% on H.V for variation should be provided. The H.V. shall be connected Delta & Secondary with star

connection. The transformer should have cable-end boxes on H.T. side suitable for up to 3 core 150 sq.mm. XLPE cable & on L.T. side suitable

for bus duct or cables as per requirement complete with test certificates from manufacturers 1. Oil conservator with filling Hole & Cap - One

No. 2. Thermometer pocket with 6" dial type thermometer switch alarm & trip contacts- Two nos. 3. Silica-gel breather with charge-

One No. 4. Plain oil level gauge - One No. 5. Drain / Sampling / Filter valve- One No. 6. Top Filter Valve - One No.

7. Explosion vent with Diaphragm - One No. 8. Rating & Diagram plate - One No. 9. Additional neutral bushing for earthing - One No. 10. Nine Lac Ninety Six Thousand Seven

327 1.00 Bi directional Roller - Four Nos. 11. Earthing terminals - Two Nos. 12. Lifting lugs - Two Nos. 996763.95 Hundred Sixty Three Rupees And Paise Ea. ₹

13. Air release plug. - One No. 14. Double float buchholz relay with Alarm and trip contacts. 15. Control cable as required from Transformer to Ninety Five Only

VCB Panel is to be provided with necessary connection to VCB relays for protection.

as per IS 1180 level-2 (b)315 KVA

Max. allowable loses at 50 % of rated load is 1.025 KW and at full load is 3.1 KW

Providing, and erecting 11 KV D.P. 9 mtr. high Structure made of 6" x 3" ‘I’-Section Girder, 4" x 2"channels, clamps, nuts, bolts etc. Suitable for

erection of the followings duly connected with necessary ACSR conductors. as per drawing approved by the Engineer- in charge complete with

following. Height as per IS 7 Mtr above ground ) (A) 11 KV 200 Amps Drop out fuses with S.R.B.P. tubes carries.-Three nos (B) 11 KV G.O.D.

switch complete with insulators, operating handle with galvanised pipe, Sq.bar etc. 400 Amp.- One Set (C) 11 KV lightening arrestor with Ninety Eight Thousand Four Hundred

328 1.00 clamp- Three Nos. (D) 11 KV shackle insulators- Six Nos. (E) The above D.P. structure should be earthed with 25 mm.X 3 mm thick double 98433.59 Thirty Three Rupees And Paise Fifty Ea. ₹

copper earth strips run separately and connected with separate copper plate earth electrode. Nine Only

Providing and erecting ISI Marked 3 core 95 Sq.mm XLPE insulated 11 KV armoured cable Aluminium conductor IS-7098 to be laid on wall with

One Thousand Three Hundred Seventy

329 220.00 clamps or in provided cable trench / pipe approved manner as directed. 1370.57 Mtr. ₹

Rupees And Paise Fifty Seven Only

Providing and erecting cable end termination kit, heat shrinkable Push on type Densons/ Raychem/ Elastimold make suitable for 11 KV XLPE

Fourteen Thousand Six Hundred Eleven

330 1.00 cable 3core 95 & 120 Sq.mm (A) Outdoor type 14611.67 Ea. ₹

Rupees And Paise Sixty Seven Only

Providing and erecting cable end termination kit, heat shrinkable Push on type Densons/ Raychem/ Elastimold make suitable for 11 KV XLPE

Eight Thousand Four Rupees And Paise

331 2.00 cable 3core 95 & 120 Sq.mm (B) Indoor type 8004.25 Ea. ₹

Twenty Five Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Design, Supplying, installing, testing of factory fabricated ready made Three phase APFC Panel Cubical Panel fabrication should be type

tested as per IEC 61921, 61439:1&2 Capacitor Duty Contactor for switching as per following Steps Incomer Switch of MCCB type

Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal earth fault protection Incomer Switch of MCCB type Icu=Ics=50KA at 400/440 Volts,

with OC, SC, internal earth fault protection,Copper tinned insulated Busbar,Cubical panel should be indoor type

with IP 43 and IK 10,Metalized polypropylene film tye3-phase 550Volt Capacitor,De tuning Reactor for each capacitor,Panel having Short

Circuit and Overload protection,Each step Capacitor having suitable MCB with Sc, OL, internal earth fault relay,Each stage having Three Lac Fifty Seven Thousand Seven

332 1.00 Stage Contactor (Capacitor load rating),PF regulator master controller having suitable steps with LCD display, Rs 485 Communication 357781.39 Hundred Eighty One Rupees And Paise Ea ₹

port, Indication LED Lamps for main incomer and ON-OFF for each capacitor bank,MS Chanel for Floor mounting, Cable entry as per Thirty Nine Only

site situation,Cooling fans for panel (D)125KVAR

Providing, erecting, testing commissioning & getting Plan Approval as well as NOC from Electrical Inspector for extensible H.T panel comprising

of one 400A. H.T. VCB incoming & Two outgoing 400 A Drawout type VCB confirming as per I.S. for use on 11 KV, 3 phase, 50 c/s. unearthed

A.C. supply system having breaking rupturing capacity of 350 MVA complete with spring operated mechanism, mechanically & automatic ON-

OFF and spring mechanism charged, discharged indicators, ON-OFF mechanical push button, operation counter necessary auxiliary switches,

closing shunt trip, air insulated busbar chamber having heat shrinkable PVC sleeves, mechanical interlocks safety shutters, isolating plugs and a Thirteen Lac Twenty Eight Thousand

1.00 VCB trolley with three vacuum interrupters with epoxy support insulators and self aligning finger type isolating contacts. The breaker shall be 1328836.80 Eight Hundred Thirty Six Rupees And Ea. ₹

Manual cum motorised mechanism & auto spring charge with TNC switch closing with following accessories. Paise Eighty Only

1. 144 mm. square flush mounting type digital multifunctional meter with communication facility - Three sets. 2. Power Factor Meter One No

Double core current transformer cast resin type having ratio 200 to 50/1 core for metering & second core for protection having required class

333 of accuracy. - Three Sets 4. Instantaneous under voltage relay& Temperature rise Tripping Relay 5. Electrical closing coil & short trip coil

operating on 110V. D.C.- Three Sets 6. Auxiliary relay for anti pumping device 7. Three phase Three limb Drawout type feeder connected &

output of 200 VA cast resin insulated potential transformer having ratio 12000V./110V. and 200 VA Burdon with 0.5 accuracy. - One No.

Common Alarm bell operating on 110V A.C.- One No. 9. Digital KWH Meter - One No. 10. Cable boxes suitable up to 11 KV 3core 150 sq.mm

XLPE cable. - Three Nos 11. 230V. A.C. to 110V. D.C. power pack for closing & tripping circuit common. 12.Breaker ON-OFF, Auto trip and spring

charged indicators. - Three Sets. 13.Phase indicating & panel illumination lamps with plug socket - Three Sets. 14.Numerical Communicable

type non directional O/C & E/F Relay with a setting of 5-250% both in O/C & E/F. -Three Set complete with necessary interconnection with air

insulated high grade copper busbar {Breaker Testing scope include Closing Time, Opening Time, VCB Hi-Pot test at Site}{ Relay Testing Scope

Include testing of all protection by three phase testing kit at site }(VCB Trolley is to be provided)

Main Fire Hydrant Pump- Electric Motor Driven: SITC of: Back pull out type -Single Stage, Self Mriming, Centrifugal Pump for Main Fire Pump

with Electric Motor, Base frame and Couplings. MOC:-Casing-CI, Impeller- Bronze, Shaft- SS 410, Sleeve-SS410. Flow Capacity: 2280 LPM Head:

65 mtr Speed: 2900 Approx Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65% of rated head

The shut off head shall not exceed 120% of rated head. UOM:-Price Per Complete set of Pump + Motor + Accessories. Note:-01. Minor civil Two Lac Ninety Six Thousand Eight

334 1.00 work like tank hole/ Core Cutting etc. are in bidders scope. Location: In Pump Room Make: Kirloskar / Lubi 296808.70 Hundred Eight Rupees And Paise Set ₹

Jockey Fire Pump- Electric Motor Driven: SITC of: Back Pull-out End Suction Type -Single Stage, Self Priming, Centrifugal Pump for Jockey Fire

Pump with Electric Motor, Mechanical Seal, Base-frame and Couplings.

MOC:-Casing-CI, Impeller- Bronze, Shaft- SS 410, Sleeve-SS410.

Flow Capacity: 180 LPM Head: 65 mtr Speed: 2900 Approx Pump shall be capable of furnishing not less than 150% of rated capacity at a head

One Lac Seven Thousand Seven

not less than 65% of rated head The shut off head shall not exceed 120% of rated head. UOM:-Price Per Complete set of Pump + Motor +

335 1.00 107756.90 Hundred Fifty Six Rupees And Paise Set ₹

Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope., Location: In Pump Room Make: Kirloskar / Lubi

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Standby Fire Pump- Diesel Engine Driven SITC of: Diesel Engine driven Standby Pumping System complete with,diesel engine, Back Pull-out

Type Single Stage, Self Priming, Centrifugal Pump, Couplings & Base-frame:

MOC:- Pump Casing-CI, Impeller- Bronze, Shaft-SS410, Sleeve- SS410.

Flow Capacity: 2280 LPM Head: 65 mtr Speed: 2900 LPM Diesel Engine includes 100 ltr diesel tank, battery, battery charger, engine oil and Five Lac Thirteen Thousand Five

336 1.00 coolant. UOM:-Price Per Each Set. Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope. Location: In Pump Room 513595.10 Hundred Ninety Five Rupees And Paise Set ₹

Make: Kirloskar / Lubi Ten Only

Fire Pump Control Panel- Auto and Manual Type. Supply, Installation and Testing of: Electric Control Panel for Electric Motor Driven Main Fire

Pump and Jockey Fire Pump. all pumps can be Start Automatically (by Pressure Switch) & Manually. Design As per the Detail Specifications

Eighty Eight Thousand Seven Hundred

337 1.00 given. UOM:-Price Per Set. Location: In Pump Room, Make: Kirloskar / Lubi 88789.10 No. ₹

Eighty Nine Rupees And Paise Ten Only

Air Vessel: SITC of Pressurized Air Vessel f Size 450 mm Dia x 2000 mm long fabricated from 10 mm thick MS Plate with 25 mm drain valve, air

release valve with ball valve on top and isolation valve. Forty Thousand Six Hundred Fifty Two

Rupees And Paise Fifty Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall FRLS type with

Five Hundred Thirty Five Rupees And

339 40.00 necessary clamps or in existing trench / pipe of following size of cables 535.30 Rmt ₹

Paise Thirty Only

- 3.5 core 70 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. - 3.5 core 70 Sq. mm Seven Hundred Forty Two Rupees And

Paise Thirty Five Only

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. - 70 Sq.mm. Nine Hundred Thirty Nine Rupees And

Paise Thirty Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall FRLS type with

Two Hundred Forty Four Rupees And

342 30.00 necessary clamps or in existing trench / pipe of following size of cables 244.42 R.mtr ₹

Paise Forty Two Only

- 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails,

Five Hundred Ninety Two Rupees And

343 2.00 insulating tape etc for following size of cables. - 4 core 16 Sq. mm 592.87 No. ₹

Paise Eighty Seven Only

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

344 6.00 connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 707.00 Seven Hundred Seven Rupees Only No. ₹

Pressure Gauge with Siphon Tube and Cock. Supply, Installation and Testing of: Pressure Gauge with Siphon Tube and Cock. MOC:-4” Dial-

Glycerin filled- Stainless Steel Body Pressure Gauge with GI Siphon Tube andBrass Cock. Size:-Dial: 4” (100 mm) Range: 0 – 16 Bar (kg/cm2) One Thousand One Hundred Sixty One

UOM:-Price Per Unit Rupees And Paise Fifty Only

Pressure Switch with Siphon Tube and Cock. Supply, Installation and Testing of: Pressure Switch with Siphon Tube and Cock. Size:- Range

suitable for System Design Pressure. UOM:-Price Per Unit One Thousand Two Hundred Seventy

Seven Rupees And Paise Sixty Five Only

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe., With necessary Pipe Fitments (Flanges, Bands,

Socket etc.),MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint, Wraping-Coating etc.), Consumables (Welding Rod, etc.) and

Labour Charge., Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 150 mm Three Thousand Four Hundred

Thirteen Rupees And Paise Eighty Only

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe., With necessary Pipe Fitments (Flanges, Bands,

Socket etc.),MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint, Wraping-Coating etc.), Consumables (Welding Rod, etc.) and

One Thousand Nine Hundred Eight

348 15.00 Labour Charge., Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 80 mm 1908.90 R.mtr ₹

Rupees And Paise Ninety Only

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

Three Thousand Seven Hundred Eighty

349 20.00 Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. 3782.45 R.mtr ₹

Two Rupees And Paise Forty Five Only

Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 200 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

Two Thousand Eight Hundred Forty

350 40.00 Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. 2847.19 R.mtr ₹

Seven Rupees And Paise Nineteen Only

Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 150 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

One Thousand Nine Hundred Twenty

351 180.00 Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. 1926.07 R.mtr ₹

Six Rupees And Paise Seven Only

Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 100 mm

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

One Thousand Four Hundred Forty

352 95.00 Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. 1449.35 R.mtr ₹

Nine Rupees And Paise Thirty Five Only

Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 80 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge.

One Thousand One Hundred Fifty Six

353 90.00 Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 65 mm 1156.45 R.mtr ₹

Rupees And Paise Forty Five Only

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge.

Nine Hundred Rupees And Paise Ninety

354 65.00 Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 50 mm 900.92 R.mtr ₹

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge.

Six Hundred Ninety Six Rupees And

355 375.00 Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 40 mm 696.90 R.mtr ₹

Paise Ninety Only

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands,

Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge.

Four Hundred Twenty Two Rupees And

356 440.00 Quality: GI, C-Class (Heavy)., Paint: UOM:-Price Per Running Meter Size: 25 mm 422.18 R.mtr ₹

Paise Eighteen Only

Gate /SluiceValve Supply, Installation and Testing of: Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments,

Sixty One Thousand Four Hundred

hardware and consumables. MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends). Standard: ISI Marked UOM:-Price

357 3.00 61443.35 Forty Three Rupees And Paise Thirty No. ₹

Per Each No. Size: 200 mm

Gate /SluiceValve Supply, Installation and Testing of: Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments,

Thirty Six Thousand Four Hundred

hardware and consumables. MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends). Standard: ISI Marked UOM:-Price

358 6.00 36471.10 Seventy One Rupees And Paise Ten No. ₹

Per Each No. Size: 150 mm

Gate /SluiceValve Supply, Installation and Testing of: Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments,

hardware and consumables. MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends). Standard: ISI Marked UOM:-Price Eighteen Thousand Four Hundred

Per Each No. Size: 80 mm Thirty Two Rupees And Paise Fifty Only

Check Valve Supply, Installation and Testing of: Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables.

MOC:-Body: Cast Iron (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 150 mm Six Thousand Six Hundred Fifty Rupees

And Paise Eighty Five Only

Check Valve Supply, Installation and Testing of: Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables.

MOC:-Body: Cast Iron (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 80 mm Two Thousand Eight Hundred Seven

Rupees And Paise Eighty Only

Check Valve Supply, Installation and Testing of: Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables.

MOC:-Body: Cast Iron (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 50 mm One Thousand Seven Hundred Eighty

Seven Rupees And Paise Seventy Only

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast

Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 150 mm Four Thousand Three Hundred Fifty

Eight Rupees And Paise Fifteen Only

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast

Two Thousand Nine Hundred Thirty

364 5.00 Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 100 mm 2939.10 No. ₹

Nine Rupees And Paise Ten Only

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast

Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 80 mm Two Thousand Two Hundred Forty Two

Rupees And Paise Twenty Only

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast

Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 50 mm One Thousand Five Hundred Eighty

Rupees And Paise Sixty Five Only

Strainer. Supply, Installation and Testing of: Y Type Strainer with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Forty Thousand Four Hundred Rupees

Mesh: SS-304. Working Pressure: 10 Bar UOM:-Price Per Each No. Size: 200 mm Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Air Release Valve- 25 mm Supply, Installation and Testing of: Air Release Valve Check Valve with necessary pipe fitments, hardware and

consumables. MOC:-Body: Gunmetal / SS. UOM:-Price Per Each No. One Thousand One Hundred Eighty Six

Rupees And Paise Seventy Five Only

Fire Hydrant Landing Valve (Stainless Steel (SS-304), ISI Marked): Supply, Installation and Testing of: Fire Hydrant Landing Valve with necessary

pipe fitments, hardware and consumables. MOC:-Body: Stainless Steel (SS-304), Working Parts: Stainless Steel (SS-304), Coupling: Stainless Three Thousand Seven Hundred

369 7.00 Steel (SS-304), Standard: -ISI Marked. Size:-63 mm (Flange End: NB 75 mm, PCD 160 mm) UOM:-Price Per Each No. 3772.35 Seventy Two Rupees And Paise Thirty No. ₹

Fire Hose Pipe (Delivery Hose)- 63 mm x 15 m Supply, Installation and Testing of: Fire Hose with Hose Couplings. RRL (ISI Mark- Type A) Fire

Hose. Hose Couplings: ISI Marked Stainless Steel. With SS Wire Binding. Standard: - ISI Marked & TAC Approved Hose., Size:-63 mm dia x 15m Three Thousand One Hundred Thirty

370 7.00 long Hose. UOM:-Price Per Each Set. 3131.00 No. ₹

One Rupees Only

Cabinet For Fire Hose (Hose Box)- Double Type Supply, Installation and Testing of: Fire Hose Cabinet (Hose Box) suitable to accommodate

no. of 15 m long fire hoses and 01 no. of nozzle. With Lock-n-key facility. Wall Mounting Design. MOC: 16 Gauge MS Box with Powder Coating Two Thousand Six Hundred Sixty One

371 7.00 Standard: - As per Guidelines. Size:- Suitable for 02 nos. of 15 m long hoses. UOM:-Price Per Each No. 2661.35 No. ₹

Rupees And Paise Thirty Five Only

Fire Hose Nozzle- Short Branch Pipe Nozzle. Supply, Installation and Testing of: Short Branch-pipe Nozzle. MOC: Stainless Steel (SS-304).

Standard: ISI Marked, Heavy Quality. Size:- 63 mm X 20 mm UOM:-Price Per Each No. One Thousand One Hundred Sixty One

Rupees And Paise Fifty Only

Fire Hose Reel Set (ISI)-19 mm x 30 m -Rubber Hose. Supply, Installation and Testing of: Fire Hose Reel Set with necessary pipe fitments,

hardware and consumables. MOC:-Drum: 16 G Powder Coated MS, Hose: 19 mm X 30 m heavy-duty RUBER hose. Shut-off Nozzle: SS-304. Five Thousand Five Hundred Thirty

With Control Valve: SS- 25mm Ball Valve. Standard: ISI Marked. Heavy Quality. Size:-19 mm dia x 30m long Hose. UOM:-Price Per Each No. Nine Rupees And Paise Eighty Five Only

Fire Service In-let (In-let Connection for Fire Brigade)-4 Way Type. Supply, Installation and Testing of: Fire Service Inlet with necessary

hardware and consumables. MOC:-Body: Heavy-duty CI. Couplings/NRV: Gunmetal. Standard: -Made As per IS Standard- Heavy duty quality.

Five Thousand Seven Hundred Sixteen

374 3.00 Size:-Couplings: 63 mm, 150 mm E-table Flange End. UOM:-Price Per Each No. 5716.60 No. ₹

Rupees And Paise Sixty Only

Sprinkler Head/ Nozzle. Supply, Installation and Testing of: K 5.6 Pendent type Standard Response Sprinkler rating of 57 deg.C. with required One Hundred Twenty Seven Rupees

accessories. MOC:-Brass Standard: UL Listed Size:-15 mm (1/2”) UOM:-Price Per Each No. And Paise Twenty Six Only

Flow Switch Supply, Installation and Testing of: Flow Switch with necessary pipe fitments, hardware and consumables. UOM:-Price Per Each No.

With all wiring/ cabling up to control panel and all electrification. Four Thousand Three Hundred Fifty

Eight Rupees And Paise Fifteen Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall FRLS type with

necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (a) 3 core 2.5Sq. mm One Hundred Eighty Six Rupees And

Paise Eighty Five Only

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (a) 2 to 4 core 2.5 Sq. mm Five Hundred Ninety Rupees And Paise

Eighty Five Only

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm Six Hundred Seventy Three Rupees And

Paise Sixty Seven Only

Providing and fixing, testing and commissioning of Drainning Valve 50mm dia with by pass drain connection as required. One Thousand Five Hundred Eighty

Rupees And Paise Sixty Five Only

Providing and fixing, testing and commissioning of CO2 type Fire Extinguisher of capacity 22.5 kg filled with Co2 Gas as per IS 15222 with

Twenty Six Thousand Four Hundred

controll discharge mechanism fitted with Hose, Horn & TROLLEY confirms to IS 2878 bearing ISI mark. Co2 Cylinder as per IS

381 3.00 26426.65 Twenty Six Rupees And Paise Sixty Five No. ₹

Fire Extinguisher- ABC Powder type, 6 kg. Supply, Installation and Testing of: ABC Powder Fire Extinguisher necessary hardware and

consumables. Stored Pressure Mechanism. Charged with MAP-50 % (ABC) Dry Powder. With wall mounting clamp. Size:-6 kg Powder. Two Thousand Six Hundred Seventy

UOM:-Price Per Each No. One Rupees And Paise Forty Five Only

Fire Extinguisher- CO2 Gas type, 4.5 kg. Supply, Installation and Testing of: CO2 Gas Fire Extinguisher with necessary hardware and

Five Thousand Five Hundred Nineteen

383 8.00 consumables. Standard: - Confirming to IS: 15683-2006 with ISI Mark. 5519.65 No. ₹

Rupees And Paise Sixty Five Only

Size:-4.5 kg UOM:-Price Per Each No.

Supplying FIRE bucket round bottom of 9 litres capacity made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside

and Red out side with FIRE mark, filled with dry-sand and kept on existing stand provided or hung on wall hook. Three Thousand Two Hundred Fifty

Two Rupees And Paise Twenty Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Supplying and erecting floor mounting stand for keeping four nos. of FIRE buckets comprising 1500 mm in length, 900 mm height frame made

out of 30mm X30 mm X 4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two Four Thousand Six Hundred Forty Six

385 1.00 coats of approved enamelled silver paint. 4646.00 No. ₹

Safety Signage- Night Glow Type: SIRC of: Single Side Printed Night Glow (Glow in Dark ) Safety Signage. Printed on PVC sticker sheet and Five Hundred Eighty Rupees And Paise

386 70.00 pasted on 3-5 mm thick PVC foam sheet. Size: 10” X 10”. 580.75 No. ₹

Seventy Five Only

RCC Hume Pipe – 300 mm: Providing and laying NP3 class RCC Hume Pipe of 300 mm dia at road crossings, including jointing, bedding,

necessary excavation, backfilling and all required materials and accessories, complete as specified. Eight Hundred Fifty Eight Rupees And

Paise Fifty Only

Approval of Fire Hydrant & Entire Fire Protection System from Local Fire Authority and any other relevant statutory authority at initial and

various other stages of work, including preparation of report/drawings as per fire authority requirement. Contractor shall include cost of all

388 1.00 101000.00 One Lac One Thousand Rupees Only No. ₹

liason work which are not explicitly mentioned above but are mandatory to have fire authority approval (any statutory charges will be paid

Medical Grade Copper Pipe – 42 mm OD × 1.2 mmThickness, seamless/deoxidized high-phosphorus copper tube, suitable for medical gas

pipeline systems, manufactured and supplied as per applicable medical gas standards, including all necessary testing, inspection, cleaning,

Two Thousand Six Hundred Twenty

389 20.00 capping and protection against contamination, complete as specified and approved by the Engineer/Consultant. 2,620.00 Rmt ₹

Medical Grade Copper Pipe : 28mm OD X 0.9mm thick seamless/deoxidized high-phosphorus copper tube, suitable for medical gas pipeline

systems, manufactured and supplied as per applicable medical gas standards, including all necessary testing, inspection, cleaning, capping and

One Thousand Two Hundred Eighty

390 460.00 protection against contamination, complete as specified and approved by the Engineer/Consultant. 1,280.00 Rmt ₹

Medical Grade Copper Pipe : 22mm OD X 0.9mm thick seamless/deoxidized high-phosphorus copper tube, suitable for medical gas pipeline

systems, manufactured and supplied as per applicable medical gas standards, including all necessary testing, inspection, cleaning, capping and

391 720.00 protection against contamination, complete as specified and approved by the Engineer/Consultant. 820.00 Eight Hundred Twenty Rupees Only Rmt ₹

Medical Grade Copper Pipe : 15mm OD X 0.9mm thick seamless/deoxidized high-phosphorus copper tube, suitable for medical gas pipeline

systems, manufactured and supplied as per applicable medical gas standards, including all necessary testing, inspection, cleaning, capping and

392 1740.00 protection against contamination, complete as specified and approved by the Engineer/Consultant. 650.00 Six Hundred Fifty Rupees Only Rmt ₹

Medical Grade Copper Pipe : 12mm OD X 0.7mm thick seamless/deoxidized high-phosphorus copper tube, suitable for medical gas pipeline

systems, manufactured and supplied as per applicable medical gas standards, including all necessary testing, inspection, cleaning, capping and

protection against contamination, complete as specified and approved by the Engineer/Consultant. Four Hundred Seventy Eight Rupees

Gas Outlet Points/ Terminal Unit : Oxygen Medical gas terminal outlet for Oxygen, wall-mounted type, suitable for medical gas pipeline system,

complete with gas-specific quick-release/terminal connection, isolation valve, face plate, identification marking and all necessary internal

components and accessories. The outlet shall be compatible with the specified medical gas pipeline and shall comply with applicable standards

for medical gas terminal units, including testing for gas tightness and functional performance, complete as specified and approved by the Five Thousand Five Hundred Rupees

Engineer/Consultant. Only

Gas Outlet Points/ Terminal Unit : Nitrous Oxide Gas-specific medical gas outlet, complete with terminal connection, isolation valve, face

plate, identification marking and accessories, suitable for medical gas pipeline system, as per applicable standards. Five Thousand Five Hundred Rupees

Gas Outlet Points/ Terminal Unit : Air 4 bar Gas-specific medical gas outlet, complete with terminal connection, isolation valve, face plate,

identification marking and accessories, suitable for medical gas pipeline system, as per applicable standards. Five Thousand Five Hundred Rupees

Gas Outlet Points/ Terminal Unit : Vacuum Gas-specific medical gas outlet, complete with terminal connection, isolation valve, face plate,

identification marking and accessories, suitable for medical gas pipeline system, as per applicable standards. Five Thousand Five Hundred Rupees

Gas Outlet Points/ Terminal Unit : AGSS Gas-specific medical gas outlet, complete with terminal connection, isolation valve, face plate,

identification marking and accessories, suitable for medical gas pipeline system, as per applicable standards.

398 6.00 10,000.00 Ten Thousand Rupees Only Nos ₹

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Gas Outlet Points/ Terminal Unit : CO2 Gas-specific medical gas outlet, complete with terminal connection, isolation valve, face plate,

399 15.00 identification marking and accessories, suitable for medical gas pipeline system, as per applicable standards. 10,000.00 Ten Thousand Rupees Only Nos ₹

Two gas Area Valve Service Unit Wall-mounted unit with two gas-specific isolation valves, pressure gauges, identification labels and accessories,

complete for medical gas pipeline system as per applicable standards. Fourteen Thousand Five Hundred

Three gas Area Valve Service unit Wall-mounted unit with three gas-specific isolation valves, pressure gauges, identification labels and

accessories, complete for medical gas pipeline system as per applicable standards. Eighteen Thousand Five Hundred

Five gas Area Valve Service Unit Wall-mounted unit with five gas-specific isolation valves, pressure gauges, identification labels and accessories,

complete for medical gas pipeline system as per applicable standards. Twenty Five Thousand Six Hundred

Medical Gas Area Alarm for 2 services : Digital area alarm panel for monitoring two medical gas services, complete with pressure sensors,

visual/audible alarms, service identification and accessories, as per applicable standards. Fourteen Thousand Five Hundred

Medical Gas Area Alarm for 3 services: Digital area alarm panel for monitoring three medical gas services, complete with pressure sensors,

visual/audible alarms, service identification and accessories, as per applicable standards. Eighteen Thousand Five Hundred

Medical Gas Area Alarm for 5 services: Digital area alarm panel for monitoring five medical gas services, complete with pressure sensors,

visual/audible alarms, service identification and accessories, as per applicable standards. Twenty Six Thousand Five Hundred

Forty Rupees Only

Oxygen Manifold (2×10): Automatic/semi-automatic Oxygen manifold for 2 banks of 10 cylinders, complete with tailpipes, NRVs, isolation

valves, pressure gauges, headers and all necessary fittings and accessories, as per applicable standards.

406 1.00 1,04,000.00 One Lac Four Thousand Rupees Only SET ₹

Oxygen Emergency Manifold (2×2): Emergency Oxygen manifold for 2 banks of 2 cylinders, complete with tailpipes, NRVs, isolation valves,

pressure gauges and all necessary fittings and accessories, as per applicable standards. Forty Seven Thousand Eight Hundred

BPC Flowmeter with Humidifier Bottle: Medical oxygen flowmeter with adjustable flow control, pressure gauge and humidifier bottle, complete

408 76.00 with necessary fittings and accessories, as per applicable standards. 1,050.00 One Thousand Fifty Rupees Only SET ₹

N₂O Manifold (2×3): Nitrous Oxide manifold for 2 banks of 3 cylinders, complete with tailpipes, NRVs, isolation valves, pressure gauges and all

necessary fittings and accessories, as per applicable standards. Forty Seven Thousand Eight Hundred

CO₂ Manifold (2×3): Carbon Dioxide manifold for 2 banks of 3 cylinders, complete with tailpipes, NRVs, isolation valves, pressure gauges and all

necessary fittings and accessories, as per applicable standards. Forty Seven Thousand Eight Hundred

600 ml Ward Vacuum Unit with Regulator: Medical vacuum collection unit of 600 ml capacity, complete with vacuum regulator, gauge,

collection bottle, necessary fittings and accessories, as per applicable standards. Three Thousand Two Hundred Fifty

Theatre Suction Trolley: Mobile medical suction trolley, complete with suction regulator, vacuum gauge, collection jars, tubing, fittings and

accessories, suitable for operation theatre use. Eighteen Thousand Five Hundred

Isolation Lockable Line Valve – 15 mm: Medical gas pipeline isolation valve, lockable type, 15 mm size, complete with fittings, identification

label and accessories, suitable for medical gas service. One Thousand Six Hundred Fifty Nine

Isolation Lockable Line Valve – 22 mm: Medical gas pipeline isolation valve, lockable type, 22 mm size, complete with fittings, identification

Two Thousand Two Hundred Fifty

414 17.00 label and accessories, suitable for medical gas service. 2,250.00 Nos ₹

Isolation Lockable line valves :28 mm: Medical gas pipeline isolation valve, lockable type, 28 mm size, complete with fittings, identification label

and accessories, suitable for medical gas service. Two Thousand Five Hundred Fifty

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Isolation Lockable line valves :42 mm: Medical gas pipeline isolation valve, lockable type, 42 mm size, complete with fittings, identification label

and accessories, suitable for medical gas service. Four Thousand Five Hundred Rupees

Supply, Installation, Testing and Commissioning of 50 mm thick Pre Fabricated Modular Operation Theater Panels (Walls and Ceiling) made out

Polyurethane foam injected at 40 Kg/m3 sandwiched between 0.8 mm thick GP and SP sheet on front side and 0.5 mm GP and SP/PPGI sheet

on back-side. The inner surface walls be fixed to the bricks wall with essential support. There will be minimum possible cavity/gap in between

solid and steel walls and will be variable to suit the architects lay out for the flush mounting of the equipments. The wall and ceiling panels

must comply with necessary provision of to JIS Z 2801/ISO 22196, BS EN 1363-1:2020, EN 1363-2:1999, EN 1364-1:2015, DIN 52210-2:1984-08,

DIN 4102-1, Class A2. Any Third-party compliance certificate mandatory. Panel should be covered with protective sheath of 300 d.f.t Anti-

bacterial Paint having undergone Washability/Water resistance Test JIS K 5663.7.12, permeability test less than 200 unit of permeability, Anti- Six Thousand Five Hundred Fifty

bacterial effect against staphyloccoccus aureus, Escherichia coli (via HALO test) and safety and causative agents such as formaldehyde, toluene, Rupees Only

xylene, paradichlorobenzene etc. Third party (NABL approved Lab) certification for EGP and thickness test certificate to be submitted at time of

Supply, Installation, Testing and Commissioning of Ceiling Filtration System - The ceiling filtration system in the surgical theatre should ensure a

unidirectional distribution of sterile air, covering all areas affected by the airflow. It should consist of a laminar flow system incorporated within

a frame made from thick extruded aluminum profiles, complete with a sealed gasket to prevent leaks. The system should incorporate "H 14"

class HEPA filters positioned in the ceiling plenum. These filters should achieve an MPPS average efficiency greater than 99.95% and a 3-micron

DOP efficiency greater than 99.99%. The filters should also be designed to handle a final pressure drop of no more than 600 Pa, operate at a

maximum temperature of 60 degrees Celsius, and function effectively within a relative humidity range of 40-50%. The filtration ceiling system

should be capable of maintaining a constant airflow velocity of 0.25 m/s at the diffuser. This should be accomplished through the use of a

diffuser or flow equalizer that ensures uniform and constant air distribution over the entire surface area. The structure holding the filtration

system, including the filter frames and top plenum, should be made from either aluminum or stainless steel. The system should be CE/UL

certified and designed to achieve an ISO 14644/1 classification of ISO 5, with a bacteriological class of B (5 CFU/m3) and particle

decontamination kinetics CP of 5 minutes. After installation, the system's performance should be validated by a third-party government- Three Lac Nineteen Thousand Nine

418 1.00 approved environmental lab to ensure compliance with specified standards. A positive pressure should be maintained inside the operating 3,20,000.00 Hundred Ninety Nine Rupees And Paise Nos. ₹

theatre to prevent contamination from external air sources. The supplier should provide test certificates for the HEPA filters and the laminar One Hundred Only

airflow systems from the original manufacturers. Furthermore, the size of the laminar airflow system should be a minimum of 8 feet by 8 feet.

Finally, the entire system should meet CE/BIS certification standards, ensuring it adheres to both European and Indian safety and performance

regulations and including validation.

The flooring within the surgical theatre should consist of a minimum of 2mm thick antistatic seamless PVC, ensuring durability and safety. This

floor should be smooth, non-slip, and made from an impervious material with sufficient conductivity to dissipate static electricity effectively,

yet not so conductive as to risk electric shock to personnel. The PVC used should be of very high quality, particularly designed for electrostatic

charge dissipation, and should not be less than 2 mm in thickness. The installation process should utilize continuous rolls, and joints should be

seamlessly welded using special PVC thermal welding units with welding bars of the same color to ensure uniformity and prevent

contamination. The sheets should be highly durable, capable of resisting shocks, indentations, and scratches. The conductive material should be

uniformly impregnated within the PVC as grains to enhance its antistatic properties. Additionally, the flooring should be inert to body fluids,

chemicals, and disinfectants, and remain unaffected by temperature variations typical within an operating theatre. It should efficiently

discharge electric charges up to 2 kV, and the electrical resistance (point to ground) should be maintained within 2.5x10^4 to 5x10^6 ohms,

ensuring no buildup of electrical charge beyond 100 volts. Floor installation should be performed by skilled workers from accredited agencies

authorized by the PVC sheet supplier. The installation should include a conductive copper grid beneath the PVC sheet, supported by liquid Four Thousand Two Hundred Forty

419 36.00 epoxy compounds to create a uniform and level surface. Copper strips should be made visible by grinding and not project more than 0.5mm 4,250.00 Nine Rupees And Paise One Hundred Smt ₹

above the floor level to prevent damage to the PVC sheet, with one earthing lead brought out from every 150 sq.ft area and attached to the Only

main earthing strip/ground. The flooring should also be mechanically shockproof, scratchproof, flame retardant, and antimicrobial. Corners of

the flooring should be uniformly curved, and a concealed cove-former (aluminium) should overlap the wall panel to a height of approximately

25mm and be sealed perfectly and uniformly. Before laying the PVC, suitable self-leveling compounds should be used to prevent any

undulations within the operating theatre. The final surface should be non-corrosive to biological fluids and detergents, with a color that is

uniform, pleasant, and matching with the ambience as approved by the respective consignee.

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

The door to the surgical theatre should be a hermetically sealed, single sliding door measuring 2.1 meters in height and 1.5 meters in width. The

door should be equipped with a controller capable of being operated by elbow switches, foot switches, and a touchless sensor, providing

multiple, accessible control options. The track for the door should be made from stainless steel or aluminum, with the running surface for the

top rollers angled appropriately to minimize resistance and facilitate smoother movement. The door leaf should be suspended using high-

quality hard plastic rollers with double bearings at the top. These rollers should run under the stainless steel or aluminum track to ensure

smooth and noiseless operation. The opening and closing mechanisms of the door should be controlled by a microprocessor for precise

electromechanical movement. The material of the door should be either SMS or HPL, with a color that matches the interior design. The door

should be designed to be strong yet lightweight for ease of use. In case the automatic mechanism fails, the door should still be able to open and

close effortlessly manually. The handle of the door should be made from stainless steel with a matte finish and equipped with a high-quality

cylindrical or ESPg lock for security. The door leaf should incorporate a high-quality synthetic rubber gasket with long durability to ensure

hermetic sealing and maintain a 99.99% air tightness at a minimum pressure of 75Pa. The floor on either side of the door should be perfectly

level, with a maximum permissible difference of +1mm, to avoid any tripping hazards or unsealed gaps. The overall thickness of the finished

Two Lac Sixty Five Thousand Rupees

420 1.00 door should range from 30-60mm, with the inner part of the door filled with CFC-free polyurethane foam, approximately 48mm thick, sealed 2,65,000.00 Nos. ₹

airtight to block any microbial ingress. The door and its controls should comply with IEE regulations, utilizing DC brushless or PMDC motors that

are effectively isolated from mains power to ensure safety and reliability. Additionally, the door should include a vision window measuring

300mm x 300mm, featuring double-glazed panels that are hermetically sealed to maintain the integrity of the seal. The movement of the door

should be as quiet as possible, and the time to start moving after receiving a signal should be adjustable between 0.5 to 20 seconds.The door

controller should be CE marked, BIS certified, or IEC 60601 certified to meet international and national safety standards. A test certificate for

the hermetically sealed door frame should be included in the pre-dispatch documents to verify compliance with the specified standards and

Supply, Installation, Testing and Commissioning of Membrane-Type Operation Switch and Communication Controller - The Operation Switch

and Comms Controller should encompass all necessary controls to ensure the proper operation and monitoring of equipment and services in

the operating room (OR). Positioned for optimal visibility in the surgeon's line of sight and the OT staff, the wall-mounted membrane-buttons

should be easily accessible to the nurse for operation and assistance. In addition to hosting a digital clock and elapsed time indicator, the panel

should feature a medical gas alarm, clearly indicating high and low gas pressures for each gas service, including vacuum, supported by an

audible alarm. The Operation Switch and Comms Controller should also provide an alarm mute option for fault annunciation, with pressure

sensors strategically located near isolation valves. Controls for general lighting, including ON/OFF and dimming, organized in groups for uniform

illumination, should be present. Furthermore, the panel should facilitate control over operating lights (major and satellite) and camera

One Lac Sixty Five Thousand Rupees

421 1.00 functions (on/off and intensity). A hands-free telephone set with memory should be conveniently situated, and temperature and humidity 1,65,000.00 Nos. ₹

controls for the room, linked to the AHU (+/5%) using NO/NC or Chilled Water/Hot Water Actuator Control Valve (whichever is applicable),

should be adjustable from the Operation Switch and Comms Controller. Real-time indicators, such as a digital room pressure indicator and

HEPA filter bank differential pressure indicator, are essential for monitoring and maintaining a safe and controlled environment in the operating

room. Telephone with Alpha-numeric keyboard is required with Speed-dialing option

Hatch boxes should be provided in each operating theater to facilitate the safe and efficient removal of waste materials to the dirty linen area

or adjacent corridor. Each hatch box should be equipped with two doors, operated electrically or motorized, designed such that only one door

can be opened at a time to prevent cross-contamination. UV lighting should be installed to ensure sterilization and should remain on when both

doors are closed, automatically turning off when either door is opened. Indicators should be provided on both sides of the operating theater to

422 1.00 monitor the door open/close status. The material of the hatch box should also be SS304 grade stainless steel, with a minimum size of 600mm x 1,05,000.00 One Lac Five Thousand Rupees Only Nos. ₹

In each operating theater, an operating list board should be installed. It should be made of ceramic with magnetic properties and should be

flush with the wall to maintain cleanliness and ease of use. LED type flat panel X-ray viewing panels should be provided, complying with

relevant electrical safety codes, and mounted flush with the wall to prevent dust accumulation and microbial growth. The body should be made

of extruded aluminum, powder-coated with a bacteria-resistant and disinfectant-resistant finish. The diffuser on the front panel should provide Twenty Eight Thousand Four Hundred

423 1.00 a uniformly lit screen, and dimming controls should be easily accessible. Additionally, a proper spring-loaded film clip with rollers should be 28,500.00 Ninety Nine Rupees And Paise One Nos. ₹

included to securely hold and easily remove films without causing scratches. Hundred Only

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

LED type flat panel X-ray viewing panel should be supplied. This should comply with relevant electrical safely codes. This should be a 2-panel

viewing screen. Mounting should be flush with the wall to avoid dust accumulation and growth or organisms between wall and panel. Body

should be of extruded aluminium powder coated black with bacteria resistant and disinfectant resistant finish. The diffuser on the front panel Forty One Thousand Five Hundred Five

424 1.00 should be a uniformly lit screen. Dimming electronic control should be enclosed at the bottom of the cabinet. Proper spring-loaded film clip 41,505.00 Nos. ₹

with rollers should be provided to hold the films firmly and to remove the film without scratches

Supply, Installation, Testing and Commissioning of Double-Bay Scrub Sink - The scrub station should be compact, designed for use in the OT

complex, and facilitate pre-procedural scrubbing. It should be made from heavy gauge type 304 stainless steel with a minimum thickness of

1.5mm and feature seamless welded construction polished to a satin finish. The scrub sink should have a front access panel for easy

maintenance of water control valves, waste connections, stoppers, and strainers. Hands-free operation should be enabled through infrared

sensors with programmable adjustments. Thermostatic mixing valve control should maintain constant water temperature and be located One Lac Twenty Six Thousand Rupees

425 1.00 behind the access panel. Timing should be adjustable to meet individual usage requirements, and units should have reduced anti-splash fronts. 1,26,000.00 Nos. ₹

An additional knee/foot-operated switch should also be provided for enhanced functionality.

Supply, Installation, Testing and Commissioning of Storage Units - Storage units should be constructed with same material, as wall and ceiling

panels. The shelves, made of glass and, should be removable for cleaning. The unit should be divided into two or more parts, each with

426 1.00 individual glass doors equipped with a high-quality locking system. The overall size of the storage unit should be approximately 200 cm (H) x 85,000.00 Eighty Five Thousand Rupees Only Nos. ₹

Supply, Installation, Testing and Commissioning of Peripheral Lighting - To enhance the operational environment of each operating theatre,

peripheral lighting and clean room luminaries should be installed, with a minimum of eight units per theatre. These lights should offer an

intensity of at least 500 Lux and be housed in highly specular anodized aluminum with an optical antiglare system to minimize visual fatigue

and glare. Each peripheral light should measure 2' x 1'. The covers for these luminaries should be constructed from highly resistant, disinfectant-

proof laminated safety glass or acrylic, featuring a stylish, fine-grained surface that complements the clean and sterile environment of the

operating theatre. The body of the luminaries should be made from sheet steel, perfectly powder-coated to resist contamination and facilitate

easy cleaning, and should be ready for connection either as individual units or within a series circuit. This setup should include digital electronic

control gear utilizing multilamp technology to optimize energy efficiency and light output. The installation of these luminaries should ensure

427 8.00 that the recess frames are gas tight. Each fitting should be flush with the ceiling and designed to be removable from either the top or bottom 12,000.00 Twelve Thousand Rupees Only Nos. ₹

for ease of maintenance. It is crucial that the light fittings are uniformly and aesthetically distributed across the ceiling to provide consistent

illumination throughout the OT, without interfering with visibility during procedures such as green mode endoscopy. Furthermore, the

peripheral lighting system should conform to IP65 or IP54 international protection ratings, ensuring that the fixtures are dust tight and

protected against water ingress, suitable for the demanding conditions of an operating theatre.

Supply, Installation, Testing and Commissioning of Electrical Wiring inside OT - Power distribution within each Operating Theatre (OT) should be

handled via distribution boards located locally to each theatre using Fire Resistance Low Smoke Wiring, layed in PVC conduits of reputed

brand. The sub mains power to these panels should be provided by the general electrical contractor, and all distribution services within the

departments should run from these panels. The power distribution unit should hold certifications such as EN, CE, FDA, IEC, and BIS to ensure

compliance with international safety and performance standards. Each wall of the MOT should have a minimum of two hybrid switch sockets

(6/16A) on each wall, in compliance with IEC standards. Light fittings within the clinical areas should be recessed LED types equipped with

control gear and sealed in accordance with the IP54 standard. This standard ensures that the fittings are protected against limited dust ingress

and water spray from all directions, suitable for clinical environments. All equipment should be fully and permanently labeled to clearly identify

and describe the function, operation, and voltage of the apparatus concerned. Upon completion of the electrical installation, tests should be

Two Lac Fifty Three Thousand Nine

carried out in accordance with the relevant sections of local wiring regulations, with results duly recorded. Each OT should have a distribution

428 1.00 2,53,996.82 Hundred Ninety Six Rupees And Paise job ₹

board (DBs) installed, with suitable wiring. A separate enclosure should house all high-voltage equipment to ensure safety and isolation. The

Eighty Two Only

remote cabinet should contain operating lamp transformers, mains failure relays, UPS, electrical distribution equipment, and circuit protection

equipment for all circuits within the operating theatre. All internal wiring within the DBs should terminate in connectors equipped with screws

and clamp springs. Connections should be of the clip-on type mounted on a rail approved by CE/IEC/BIS standards and labeled with indelible

proprietary labels. All internal circuits should be protected by individual fuses or miniature circuit breakers to ensure safety and manage

potential electrical faults effectively.

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

Double Dome OT Light with Ceiling mounted Double Dome LED OT lights having following features and enclosed technical specifications,

having Mobile App Connectivity, Battery Backup -Light intensity Ec - 160 000 & 160 000 lux, - Light intensity adjustment - 10 – 100% (using

Digital Capacitive Touch (Fully Remote Controlled) - Color temperature Tc (with adjustment) -3800 – 4800 K -Light field diameter d10 at Ec -

- 150 mm -Working range - 1 m -Color rendering index 93Ra - Focusing Preset: Adjustable - LED Average life - 50000-60000 hrs - Diameter of

Light - not less than 650 mm per dome - Power Consumption - not more than 120W OT Light should be BIS marked; manufacturer should have Three Lac Sixty Five Thousand Rupees

CDSCO License for this product under Class A, Compliant to IEC standards such as IEC60601-1:2005+A2:2020, IEC 60601-2-41:201 (Relevant Test Only

Certificates to be submitted with Bid) Clause-wise Technical Compliance to be.

Single-arm surgery/anesthesia pendant designed for Operating Theatres should feature a compact, modular configuration to meet the precise

requirements of hospitals, enabling customization to suit specific operational needs of both Operating Theatres and Intensive Care Units. It

should be equipped with robust ceiling support capable of mounting a selection of arms. The extension arm, pivotal for functionality, should

allow horizontal movement with a radius of 800-900mm and provide a level rotation ranging from 0 to 330/340 degrees, with both the

extension arm and terminal box designed to rotate together and independently for maximum versatility. The pendant should support a net

loading capacity of min. 100 kg, accommodating a variety of medical instruments and devices securely. For medical and electrical services, it

should offer configurations that include at least two oxygen outlets, two vacuum outlets, one medical air, one medical air at 7 bar, and an

optional nitrous oxide outlet (In-scope of MGPS vendor) Additionally, there should be six main sockets, each capable of supporting 5 to

amps, conforming to universal standards to facilitate the operation of various medical and electronic devices. In terms of materials and

Two Lac Twenty Four Thousand Nine

construction, the pendant should be crafted from high-strength aluminum alloy with a sealed design to enhance durability and maintain sterile

430 1.00 2,24,992.38 Hundred Ninety Two Rupees And Paise Nos. ₹

conditions. The arm itself should be made from high-density aluminum alloy extrusion, ensuring both strength and reliability. Installation of the

Thirty Eight Only

pendant should be ceiling-mounted to provide a reliable and firm setup, optimizing space usage in the Operating Theatre or ICU while

seamlessly integrating with existing medical systems for managing medical gas, electrical services, data communication, and equipment.

Additionally, the pendant should include practical features such as a stainless steel IV pole and a ward vacuum unit clamp to further enhance its

utility in a medical setting. With a net weight of approximately 105 kg, accessible by the equipment carrier, the pendant should be robust yet

manageable, ensuring it meets the rigorous demands of modern medical environments.

Quantities Estimate Rates

Item Total Amount According to

Item Total Amount According to

Estimated But may Be Item of Works Unit

No. Estimated Quantites Rs.Ps.

More Or Less In Figures Rs.Ps. In Words

In Wards: - Seventeen Crore Sixty Six Lac Eight Thousand Seven Hundred Rupees Only

Credit Value:….Less Value For Dismalnting Old Structure CHC Main Building & Staff Quarter, Mouje & Taluka - tarapur, Anand, Gujarat.

(This Item Nos. 431 Shall Nos.t quote less value than Credit Value in Tender I.e. Rs 4,20,000.00/-) ,(Up set Value of the salvaged items of .Rs Rupees Four Lakh Twenty Thousand

4,20,000.00/- the Credit Value to be quoted shall Nos.t be less then upset value mentioned above the quoted amount shall be deducted from Only.

the Contractor's First R.A.Bill) As Per Valuation Report

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which NO extra payment shall be made.

2 The labour cess and Testing charge will be deducted as per prevailing rules i.e. 1% (LC) and 1% (Tsting) of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost of

difference of cement consumption have been deducted from the rate of original item at the rate of input rate mentioned in all the tender. Input rate is Rs. 5234 MT.

5 GST extra applicable in case of work based on SOR 2024-25 only.

6 Must be Deduct the credit value of the demolition of the old structure, amounting to Rs. 4,20,000.00/- (Fix Amount, no tender deduction consider above / below), from the 1st Running Account (RA) Bill.

Deputy Executive Engineer Executive Engineer

P.I.U. Zone-5, Anand P.I.U. Zone-5, Anand

Deputy Executive Engineer (Ele.) Executive Engineer (Ele.)

P.I.U. Zone-5, Anand P.I.U. Zone-5, Anand